模具名称英文对照表

模具英文缩写对照表模具 Mould tooling模芯 Parting Core局部视图 Partial View冷料# Cold Slag线切割 Wire E.D.M轮廊 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press 水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leaderd Pin镶件 Mold Insert加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary名称块表 Title Block版本标识 Revision Level材料清单 Stock List制模 Build Mold手动滑块 Hand Slide漏水测试 Leak Test流道排气 Runner Vents抛光 Draw Polish侧抽芯 Side Action加强筋 Reinforcing三角撑 Gusset柱子 Bossed出模斜度 Draft外廊 Contour落单会议 Kick-Off Meeting装卸孔 Handling Hole运输安全带 Moldstrap码模槽 Clamp Slot撑头 Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位 Leader Pin Location耐落胶 Teflon Paste偏移量 Offset水塞 Water Line Plug撬模脚 Ppy Slot重新加工 Reworked配件 Components补偿 Compensation平面度 Parallel倒角 Chamfer模胚 Mold Base热嘴 Hotnozzle火花机 Edm熔接线 Weildline压机 Press晒纹 Texturing梯形 Trapezoid凸缘(法兰) Flange方铁 Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate后模镶针 Core Pin拉圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴 Extension Nozzle Bushing水口板导套 Runner Stripper Plate Bushing 定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速项 Accelerated Ejector客户 Client产品名 Part Name产品编号 Part No缩水 Shrinkage版本 Rev模胚 Mold Base下模镶件 Core Block上模镶件 Cavity Block小镶件 Sub-Insert下模小镶件 Core Sub-Insert上模小镶件 Cavity Sub-Insert行位 Slide行位镶件 Slide Insert压条 Gib压紧块（铲机） Jaw硬片（摩擦片） Wear Plate水口铁 Runner Bar上模水口铁 Upper Runner Bar下模水口铁 Lower Runner Bar弹簧 Spring水口勾针 Sprue Puller Pin顶针 Ejector Pin撑头 Support Pillar直身锁 Side Lock斜度锁 Interlock锁模板 Safety Bar‘O’形圈（密封圈） O'Ring喉塞 Plug隔水片 Baffle波子螺丝（行位定位螺丝） Ball-Catch 斜顶 Lifter控制开关 Switch回针 Return Pin斜导柱 Angle Pin推板 Stripper PlateA’板 A'PlateB’板 B'Plate方铁（垫铁） Spacer Block顶针板 Ejector Plate顶针底板 Ejector Retainer Plate垫板 Retainer Plate垃圾钉 Stop Pin有托顶针 Shoulder Ejector Pin顶针板导套 Guided Ejection Bushing针板导柱 Guided Ejection Leader Pin唧嘴 Sprue Bushing三板模延伸式唧嘴 Extension Nozzle Bushing水口板导套 Runner Stripper Plate Bushing 定位圈（法兰） Locating Ring管钉（定位销） Dowel Pin管状管钉 Tubular Dowel吊环 Safety Hoist Ring日期印 Dating Insert环保印 Recycling Insert气顶 Air Poppet Valve截水口镶件 Runner Shut-Off Insert早回 Early Ejector Return加速顶 Accelerated Ejector扁顶 Blade出模斜波 Draft手动滑块模具 Hand Slide-In Type Mold回针板 Backup合模 Shutoff空隙槽 Clearance Slot导柱及导套 Leader Pin Bushing水口拉钩 Spuer Puller模框镶件 Pocket Insert成型热固性塑胶模具 Thermoset Mold三板模 3-Plat Mold分型面 Parting Line司筒 Ejector Sleeve垫圈 Washer熔接线（夹水纹） Weldline吸针 Sucker Pin回针板 Retainer Plate顶出板 Knock -Out Plate电动安全开关 Electrical-Safety Switch 脱开 Cut Of Position预先决定 Preload缓冲器 Bumper衬垫 Cushion公差 Tolerance突然性动作 Slam销针 Dowel钩槽 Gib精磨 Finished通框 Through Window粘后模 Sticking Core粘水口 Sticking Sprue夹水纹 Weld Line变形 Warpage走水不平均 Filling Uneven走不齐 Short Shot挂成品 Part Hanging漏水 Water Leakage刮花（擦伤） Galling漏电 Ele Leakage困气 Air Trapping温度 Temperature注塑模 Injection Mold 入水 Gate试板 Sampling压力 Pressure倒圆 Fillet顶棍 Ejector顶白 Stress Mark粘前模 Sticking Cav名称块表 Title Block版本标识 Revision Level材料清单 Stock List斜导柱（斜边） Angle PinA板 A'plateB板 B'plate倒扣 Under-Cut披峰 Flash缩水 Sink Mark氮化 Nitride不规则四边形Trapezoid缩水 Shrinkage连续的 Consecutive雕刻 Engrave出模角 Draft分模面 Parting Surface 擦位 Shut-Off(S/0)导套 Bushing回针 Return Pin加硬 Harden唧嘴 Sprue设计筒图 Design Preliminary丝印 Silkprint不干胶 Adhesive Sticker导向针 Guide Din公差 Tolerance线切割 Wire-Cut电火花 Edm抛光 Polishing蚀纹 Texture探热针 Thermocouple三打螺丝毫（限螺丝） Stripper Bolt盖板 Cover Plate齿轮 Gear油唧 Hydraulic Cylinder司筒 Ejector Sleeve导柱 Leader Pin冷料# Cold Slag线切割 Wire E.D.M.轮廓 Contour螺纹孔 Tapping Hole连接件 Fittings斜针 Angle Pin接合 Engage替换镶件 Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press水嘴接头 Water Fittings螺纹 Eyebolt Thread回针 Stop Pin二级顶出针 Sub-Leader Pin镶件 Mold Insert锁定位 Lock楔子(铲鸡) Wedge高产量模量 High Volume Running Mold剖面图 Cross Section 模具结构 Mold Construction 模芯 Parting Core局部视图 Partial View热流道 Manifold热嘴 Hot Nozzle型腔数 Cav No 模号 Mold No胶料 Material尺寸 Dimension重要尺寸 Critical Dimension 雕刻 Engrave托司 EJ.GUIDE PIN。

模具术语中.英文对照1. MOULD BASE 模架2. TOP CLAMP PLATE 水口板3. STRIPPER PLATE 水口推板4.A PLATE A板5. B PLATE B板6.SUPPORT PLATE 托板7. SPACER BLOCK 方铁8.EJECTOR RETAIMER PLATE 顶针面板9. EJECTOR PLATE 顶针底板10. BOTTOM CLAMP PLATE 底板11. RETURN PIN 回针12. SUPPORT PIN 拉杆13. GUIDE PIN 导柱14. SHOULDER GUIDE BUSH 托司15. STRAIGHT GUIDE BUSH 直司16. EJECTOR GUIDE PIN 中托司17. EJECTOR GUIDE BUSH中托边18. CA VITY-1~2 型腔1~219. CA VITY-INSERT-1~2 型腔镶件1~220. CA VITY-INSERT-PIN1~2型腔镶针21. CORE-1~2 模钶1~222. CCORE –INSERT 1~2模钶镶件1~223. CORE -INSERT-PIN1~2模钶镶针24. LOCA TING RING 定位川25. SPRUE-BUSHING 唧咀26. SLIDES BLOCK 行位(滑块)27. SLIDE-INSERT 行位镶件28. SLIDER-PLATE-BLOCK 压块29. SLIDE ADJUSTMENT PLATE行位镶件30. SLOPING WEDGE 铲鸡31. INCLINED BLADE 斜顶32. EJECTOR- BLOCK顶块33. EJECTOR-POLE 顶杆34. EJECTOR-PIN 顶针35. STEPPED EJECTOR-PIN有托顶针36. EJECTOR BLADE扁顶针37. EJECTOR SLEEVE 司筒38. ANGULS GUIDE-PILLAR 司筒针39. RUNNER LOCK PIN 水口钩针40. ANGLAR GUIDE-PILLAR 斜导柱41. LIMIT-PIN 限位柱42. SUPPORT-PILLAR 支撐柱43. SUPPORT-BLOCK 支撐块44. SPRING 弹簧45. STRAIGHT-INTERLOCK扣鸡46. NYLON PLUG 尼龙胶塞47. SCREW PLUG 螺丝堵48. COPPERY PLUG 铜堵49. LOCK 管位50. ISOLATION PLATE 隔水片51. SCREW 螺丝52. LIMIT SCREW 拉杆螺丝53. PEG NAIL 销钉54. LAYSTALL NALL 垃圾钉55. A VERT SCREWS 防转钉。

assemble mould合箱assembling mould装配铸型baked mould干型bar mould多穴压模big-end-up mould上大下小钢锭模black mould of rice 黑变病blank mould turnover 雏型模翻转blowing mould吹模blue mould of citrus 柑桔青霉病cap mould压顶线脚car type mould conveyor 小车式铸型输送机case mould plaster 母模用石膏casting mould铸型centrifugal casting mould离心铸造铸型ceramic mould casting 陶瓷模注法channel mould槽模chill mould冷铸型(模)close mould封闭铸型close mould (铸造用) 合箱closed mould闭式模; 闭式压模cold-punching mould冷冲模collapsible mould分室模composite ceramic mould复合陶瓷型composite mould casting 复合型铸造copper mould base 铜模底copper mould wall 铜坩埚壁corrugated mould波形铸模cover mould压缝线脚covered floor mould盖箱地面铸型cylinder mould machine 圆网造纸机double-mould-broad ridging plough 双壁起垄犁draw mould薄壁模子driel mould干型drip mould滴水线脚dry sand mould干型ear mould耳模electric pole mould hanger 电杆模型吊架end mould端模Erical mould可压锭模; 挤压锭模evacuated mould空腔模face mould面模fall wheat snow mould冬小麦雪霉病falling mould曲型线条female mould阴模fixed mould固定模flaskless mould无箱铸型floating-point mould浮点模型floor mould地铸模fluted mould波形模foam sponge mould泡沫胶硫化模footed mould压印底圈的模型forging mould锻模front mould前模full-mould casting process 实型铸造gang mould成组模; 成组模板garden mould园土get in the mould垫平铸型glass mould玻璃型; 玻璃铸型glass mould diode 玻璃模二极管graphite mould石墨型grass mould腐草土gray mould灰霉green mould绿霉病green mould of citrus 柑桔绿霉病ground mould地面铸型; 堆土木模gypsum mould石膏型hair mould毛霉hair mould sprout 毛霉芽half mould半型hoist for mould board carrier 模板车升降机hump mould压坯用阳模ice mould冰铸ingot mould钢锭模; 铸锭模; 铸锭型; 锭模ingot mould milling machine 钢锭模铣床ingot slab mould扁钢锭模insulating mould coating 隔热涂料integral mould整模型invested mould熔模铸型iron mould铁锈迹leaf mould叶霉; 腐叶土loam mould泥型lower mould half 下模; 凹模male mould凸模; 阳模master mould母型; 原模mismatch in mould铸型错箱mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型mould addition 钢锭模添加剂mould and die milling machine 模具铣床mould assembling 合箱mould assembling and closing 铸型合箱mould assembly 合型mould blower 吹型机mould board 造型板; 样板mould boardless plough 无壁犁mould buggy 钢锭模车mould case 模制壳mould clamp 卡具mould clamps 模型紧固夹mould cleaner 模具清洁剂mould closer 合箱机; 合箱装置mould coating material 钢锭模涂料mould core 模芯mould cover 腐殖质层mould cure 模塑硫化; 模型硫化mould dam aged sweet potato poisoning 黑斑甘薯中毒mould dimension 铸型尺寸mould drag 下半箱mould drying 铸型烘干mould efficiency 模塑效率mould emptier 脱模机构mould erosion 铸型冲蚀mould facing 涂料mould fitter 合箱工mould flat gauge 样板mould form 模型型腔mould fungus 霉菌mould growth test 长霉试验mould half 半型mould hardness 铸型硬度mould impression 模型内腔; 模型型腔; 模穴mould in a snap flask 无箱造型mould in the pit 地坑造型mould inoculation 型内孕育mould jacket 型套mould kernel 模芯mould life 模型寿命mould lifting 铸型起模mould lining 坩埚衬里mould loft 放样间mould loft floor 放样台mould lofter 放样工; 放样工人mould loftsman 放样工; 放样工人mould machine 模塑机mould machine of cereal seed selection 谷物选种机mould mark 模缝条痕mould matrix cathode 模制阴极mould oil 脱模油mould on end 垂直分型造型mould pig iron 型铁mould plaster 模型用石膏mould plate 模型板mould plunger 阳模mould plunger force plug 凸模mould preparation bay 钢锭模准备跨mould press 模压机mould pressing 旋压成形mould proofing 防霉mould rains 梅雨mould release 分型粉mould relese 脱模mould rollover unit 翻箱装置mould sand 型砂mould seam 模缝mould setting-and-stripping bay 钢锭模准备和脱锭跨mould shift 错箱mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩mould splits 模组分mould stripping 铸型起模; 拆模mould susceptibility 感霉性mould test chamber 霉菌试验箱mould train 模组mould turnover 翻箱mould unloading 出模; 脱模; 卸模mould veining 铸型裂纹mould vibrator 模板振动器mould vulcanization 模塑硫化mould wash 脱模涂料mould wash mixer 涂料搅拌机multiple cavity mould多型腔铸型; 多巢模multiple mould多件石膏模multiple-part mould多箱铸型needle mould针模one-piece mould整体铸型open bottom mould底开式钢锭模open mould明浇铸型; 敞口铸型open sand mould明浇砂型optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪ornamental mould艺术造型pallet conveyer mould machine 滑板输送式造型机paper mould纸型paste mould衬碳模paste mould ware 衬碳模成形的制品peat mould泥炭土permanent mould永久铸型pig mould锭模plural mould operation 多模操作porous mould多孔模型positive mould阳模; 阳压模press mould压模press mould ware 模压器皿pressing mould压模process of unconventional heat treatment of mould模具非常规热处理工艺quadrant mould四开木压条real mould实模型rectal suppository mould肛门栓剂模refractory shell mould耐火材料壳型removal of the mould拆模reverse mould倒模; 倒型revesing permanent mould双面金属型ring mould瓶颈模ring-shaped mould环型铸模risk of mould发霉险roast sand mould干砂型rubber mould橡胶皮模running mould模筛样板; 模饰样板saccharifying mould糖化霉sealing of a mould铸型密封section mould型模sectional mould镶合砂型semi-automatic mould半自动模; 半自动塑模semi-chilled mould casting 半金属型铸造; 半冷模铸造semi-permanent mould半永久型; 半永久性模semiclosed top mould半封顶锭模shell mould machine 壳型造型机shiftable mould-board 可拆换的刀片sign mould符号模型single cavity mould整体铸型single mould单件模型skin dried mould面干铸型skin drying mould表干型sleeper steel mould轨枕钢模slime mould粘菌slip flask mould脱箱铸型snap flask mould活箱造型; 无箱铸型snapflask mould脱箱造型snow mould雪霉病; 雪疫病soap mould皂模sooty mould烟霉; 煤污病sooty mould of rice plant 水稻煤病sooty mould of tea 茶叶煤污病spacing mould隔膜split mould对开模stagnant mould不动模型standard steel ingot mould标准钢锭模steel mould钢锭模; 钢模steel mould for electric pole 电杆钢模stock mould定型模stripper-plate mould脱模板塑模sweeping loam mould刮泥型swell of a mould胀砂symbol mould符号模型tape of mould模型锥度thin-walled metal mould薄壁金属型thin-walled mould薄壁结晶器three-cavity mould三开箱铸型tilt-mould billet 可倾模锭坯tire recapping mould轮胎翻修硫化机tomato leaf mould番茄叶霉病top mould half 凸模two-cavity mould双型腔铸型variable-point-mould变点模型vegetable mould腐殖土verge mould山墙檐口线脚waste mould gypsum 废模石膏watch-case mould表壳式压模water mould水霉wood casting mould木质铸造模型X-mould machine 多模成型机。

模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。

模具常用名稱中英文對應表彈弓膠Rubber Spring R.S.斜邊釘Taper InterLock T.L.鋼公electrode熱膨脹系數thermal expanion coefficient拉膠Parting Lock PA.L.斜導柱Angular Pin A.P.加工程序secondary process粘度viscosity 頂針Ejector Pin E.J.P.定位扣"P" Lock P.K.翹曲warpage 扁頂針Ejector Blade E.J.B.銷釘Dowel Pin D.P.有托頂針Stepped Ejector Pin S.E.J.P.斜鎖位taper Block Set-ky TYPE T.B.S.唧嘴sprue bushings附針(導柱)guide pins司筒針Ejector Sleeves E.J.S.水口扣針butt joint司(導套,套司)guide pin bushings頂針ejector pins平行板parallels單頭柳釘blind rivet電阻焊接resistance welding頂板ejector plates壓板clamping plate平接butt joint固定圈retaining ring面針板ejector pin retainer plate墊片pressure電動螺絲批screw driver,electric螺絲批screw driver邊釘loader pins碼板mountingplates氣動螺絲批screwdriver,pneumatic點焊spot welding受力單位force units托板(固定器)retainers換能器energy converter彈簧夾spring clips受力板force plate勾針pot plungers 焊條filler rod彈簧墊圈spring washer模板cavity plates頂針pots磨擦焊接friction welding雙頭螺栓stud模塊cavity blocks頂針板pot retainers氣焊gas welding轉矩扳鉗torque wrench模鑲件cavity inserts托板backing plates膠glue觸針welding horn口哥塊core blocks頂針knockout pins熱壓封口heat sealing超聲焊接ultrasonic welding內口哥鑲件core inserts頂出條knockout bars搭接lap joint固定口哥鑲件fixed cores頂出板knockout pin plates保險螺絲lock nut/lock washer活動口哥鑲件moveable cores壓條,碼板gibs 螺母nut行位,滑動板slideslayout排位web impregnation網架浸漬release agent脫模劑knockout pin同"ejector pin"guaranteed tool life 制模公司保証啤數rotation spindle旋轉軸knockout plate同"ejector plate"spare part requested后補件ante chamber預接待室roving紗束locating ring定模環tech point checklist工程提點latch鎖模扣seamless無縫mould insert模型嵌件parting line分模線puller拉針solidify凝固化pinpoint submarinegate針狀隱蔽澆口gating point水口點oil grooves油坑spray gun噴漆槍port壓力筒cavity marking頭號sheet steel薄鋼squeegee涂刷劑punch plate沖孔板date code日期指示印mould ledge模架steam jacket汽套ribs肋條,骨位12NC marking12N印spray paint噴油surge tank溢水槽ring gate環形澆口mould marking模編號tempo print絲印transfer chamber傳送室round support block園托板sub-contracting item外判加工water circuit水路vacuume pump真空泵runner澆道sketch草圖vent通氣孔runner plate澆道板split mould裂開式模finishing表面處理mould stripping出模,胱模,下模spider gate=spoko gate輪輻澆口2 plate mould2板模polish磨光sprue gate豎澆口combined tool合作模grin磨床sprue bushing豎澆口？套lathe車床sprue puller澆口拉鉤mill銑床standard gate標准澆口wire cut線切割stripper plate脫模板support block托板milling銑flash/buns披鋒air vent inserts氣坑milling cutter銑刀flow mark/flow lines/silverstreak 射絞spare parts備用部分nitriding氮化finger marks/fingerstaing/finger print 手指印safety systems安全系統photo-engraving光刻improper degating/gate toolong 水口過長mould ability可注塑膠pitch節距mixed colour/off colour 顏色不對稱short moulding走膠不齊polishing磨光orientation移位sink marks凹痕,縮水reamer鉸刀、鉸床ripples波浪紋warpage彎曲變形reaming絞孔scratched刮花paint ability可噴油,絲印roller coating滾筒涂層short shot缺模no. of cpk dims控制尺寸數量sanding砂磨sink marks縮水痕sec.of cpk check 草圖控制尺寸位置scraper刮刀spray marks水花紋shaping修刨、成形string拖膠線mould polishing省模,模具拋(省) shear剪stress marks扯白痕EDM電火花,放電加工slotting立刨thickness out of spec./undersize 尺寸不合wire EDM線切割snips平頭剪unstretched未拉spanner扳手vent marks氣紋texture蝕紋spray painting噴漆warpage扭曲，熱變形water contamination水漬three-plate mould三層模two-plate mould雙層模。

工程部 / Design department:1) Designer - 设计师。

2) Assembly drawing - 模具组装图。

3) Mold layout - 模具结构图。

4) 2D product drawing - 2D产品图。

5) 3D product data - 3D产品数据。

6) Part drawing - 散件图。

7) Insert molding - 镶件模。

8) 2 color mold / Double injection tool - 双色模。

9) Hydraulic system - 油/水压系统。

10) Parting line - 分模线。

11) Air venting - 排气槽。

12) Cooling system - 冷却系统。

13) Screw - 镙丝。

14) Hot runner system - 热流道。

15) Valve gate - 伐针入水口。

16) Fan gate - 扇型入水口。

17) Pin point gate - 针点进胶。

18) Moon gate / Banana gate - 香蕉，象牙入水口。

19) Submarine gate - 潜水口。

20) Injection machine tonnage - 注塑机吨数。

21) Number of cavity - 穴数。

22) Steel - 钢材。

23) Copper - 铜。

24) Tungsten copper - 钨铜。

25) Beryllium copper - 铍铜。

26) Hardening - 加硬/淬火。

27) Tempering - 回火。

28) Chroming - 电镀。

29) Painting - 喷漆。

30) Resin - 胶材。

31) Printing - 丝印。

32) Texturing - 嗮纹/咬花。

33) Socket screw - 带肩镙丝。