GROUP产品说明书带封面

PRODUCTS10R EGOP R O D UC TS10YEA RW A R RAN T YNew 3” Swing-Check ESV for Bulk Plants 6024Redesigned G8475 ASME Multivalves ® with Pressure Gauge Port New A3209PAF ActuatorRedesigned Internal Valve A3217FA & A3217DFA New 8475-50L Extended Fill AdapterProduct Updates2008LApplicationThese Multivalves® are designed for use in single opening ASME containers equipped with a 21⁄2” M. NPT riser. They can be used with underground ASME containers up to 639 sq. ft. surface area, and above ground ASME containers up to 192 sq. ft. surface area. A separate opening is required for liquid withdrawal. The MultiBonnet® is standard on this valve.Features• The most complete Multivalve® assembly in the LP-Gas industry.• Combines double back check filler valve, vapor equalizing valve with excess flow, pressure relief valve with protective cap and chain, service line shut-off valve, fixed liquid level gauge, “junior” size float gauge flange opening and plugged pressure gauge opening in one unit.• Designed for installation of a 1/8” FNPT pressure gauge or pressure gauge connection. The pressure test port will communicate to the downstream side of the service valve.• Double back check filler valve has filling capacities matched to the high capacity pumps and meters on modern delivery trucks.• Vapor equalizing valve with excess flow has increased capacity matched to the filler valve.• Internal threads accommodate 21⁄2” M. NPT riser pipe connection and a 3⁄4” F. NPT connection for a customer furnished liquid baffle tube.• MultiBonnet® allows quick and easy repair of bonnet.MaterialsBody .............................................................................. Forged Brass Handwheel ........................................................... Aluminum Die Cast Valve Stems ............................................................................... Brass O-Rings .................................................................... Resilient Rubber Seat Disc (shut-off valve) .......................................................... Nylon Seat Disc (other) ...................................................... Resilient Rubber Relief Spring ............................................................... Stainless SteelOrdering InformationG8475RU L3⁄4" NPT thd.for standardweight baffle pipe.Length to suit tank(furnished by customer).21⁄2" NPT riser pipe connection30"With the service valve closed the pressure port will be isolated from the container. This will allow a high pressure leak test to be conducted without disconnecting the pigtail from the service valve.ApplicationThis actuator permits the A3209 internal valve to be opened and closed remotely. It can be used with the air brake system on a bobtail, or can be used at a dispenser or bulk plant.Features• All necessary hardware for installing the actuator is included • A 212°F thermal element is included to meet requirements of NFPA 58 or 49CFR.MaterialsMounting Bracket ....................................................... Stainless Steel Connecting Rod .......................................................... Stainless Steel Return Spring ............................................................. Stainless SteelA3209PAFA3217FAU LApplicationDesigned primarily for LP-Gas and anhydrous ammonia filling and/or withdrawal on MC331 bobtail delivery trucks, transports and stationary storage tanks with flanged pumps or piping. Installation is quick and easy, and the valve may be operated manually by cable or pneumatically.Lever available on right or left side to allow for installation without the use of an extra pulley.FeaturesProvides More Efficient Operation• Flow passages designed to allow substantially higher without cavitation or loss of efficiency--saving time and money.• Simple operating lever facilitates easy adaptation of all cable controls.• Lever available on right or left side to allow for installation without the use of an extra pulley.• Nylon bearing supported operating shaft provides smooth, easy operation.Less Frequent-Easier Maintenance• Stainless steel screws resist rusting and are easily removed during valve disassembly.• Heavy duty rod wiper helps minimize dirt and foreign material from entering operating shaft and hampering operation.Durable Construction• Cadmium plating helps resist corrosion during storage and use.• All ferrous materials with a temperature range of -40° F. to +130° F. and a pressure rating of 400 psi.• Sturdy retaining ring secures operating cam to provide for more durable, slack-free operation.• Built-in excess flow valve.• Specify RegO® Internal Valves on your next new tank or when your truck is rebuilt.8475-50L Repair Kit for 8475 & 8477 Multivalves with 1 3/4- 6 ACME Filler ValveWARNING: Installation, disassembly, repair and maintenance must be performed only by qualified personnel.MAINTENANCE ON THE UPPER BODY OF THE ABOVE VALVES SHOULD BE PERFORMED AFTER ALL GAS IS EVACUATED FROM THE CONTAINER AND THE VALVE REMOVED. EMERGENCY SERVICE MAY BE CARRIED OUT WITH THE VALVE INSTALLED BUT ONLY UNDER THE SAME CONDITIONS REQUIRED FOR RELEASING LP-GAS (see caution).Installation, usage and maintenance of this product must be in compliance with all Engineered Controls International, Inc. instructions as well as requirements and provisions of NFPA #54, NFPA #58, DOT, ANSI, all applicable federal, state, provincial and local standards, codes, regulations and laws. Inspection and maintenance on a periodic basis is essen-tial. Be sure all instructions are read and understood before installation, operation and maintenance. These instructions must be passed along to the end user of the product.CAUTION: Contact or inhalation of liquid propane, ammonia and their vapors can cause serious injury or death! NH3 and LP-Gas must be released outdoors in air currents that will in-sure dispersion to prevent exposure to people and livestock. LP-Gas must be kept far enough from any open flame or other source of ignition to prevent fire or explosion! LP-Gas is heavier than air and will not disperse or evaporate rapidly if released in still air.Disassembly and Repair ProcedureCAUTION: READ THROUGH ALL OF THESE INSTRUC-TIONS, INCLUDING THE NOTICE ANDTHE BACK OF THIS SHEET, BEFORE DISASSEMBLY OR REPAIR.ponent parts and valves.2. Depress upper check to assure assembly is functioning properly. If check assembly is not functioning properly, then additional repairs maybe necessary after gas is removed from container.3. Use a 7/8” allen wrench or a suitable wrench to loosen filler valvebody by turning counterclockwise. Remove filler valve body and seal gasket and discard.4. Remove old gasket from the main body and discard.If valve is repaired with gas in the container(Emergency Service), go to step A2. If the valve is repaired with all gasevacuated from the container,proceed to stepA. Disassembly - See Figure 11. Remove cap and save for reassembly.B. Reassembly - See Figure 2NOTE: If tank is under LP-Gas pressure, wear gloves to complete remaining reassembly procedures. Stand aside from top of valve.1. Place new gasket in main body.2. Center the filler valve extension assembly over the disc retainer assembly (Upper Check) and turn into threads. Torque to 1500-1800 in/lbs.3. Pressurize tank if necessary and check all seal joints with a high quality leak detection solution.4. Replace cap.And we know how important it is to select the highest quality components from suppliers you know and trust- suppliers right here in America, just like us.When you select an American made RegO Regulator, you are supporting sixteen other American manufacturers whosupply our components-suppliers who are not always thecheapest but are always the best.Reliable products from trusted suppliers you have known for years- that is how we are able to keep supplying you the best-built propane regulators. Still made in America with a 25-Year Service Life and 10-Year Warranty.Still Your First Choice...Do You Care About What’sIn Your PropaneRegulator?WE DO.PRODUCTS10R EGOP R O D UC TS10YEA RW A R RAN T YR EGO R E G U L A T O R S2525 YE AR S I L VE R SE RV I CE LI F EStill Your First Choice... Still Made in America.100 RegO Drive, Elon NC 27244 USA Phone: (336) 449-7707 Fax: (336) 449-6594Do You Care About What’s In Your Propane Regulator?WE DO.from suppliers you know and trust.And we know how important it is to select the highest quality componentsfrom suppliers you know and trust.Suppliers right here in America, just like us.When you select an American made RegO Regulator, you are supporting sixteen other American manufacturers who supply our components.Suppliers who are not always the cheapest but are always the best.Reliable products from trustedsuppliers you have known for years- that is how we are able to keepsupplying you the best-builtpropane regulators.Still made in America with a 25-Year Service Lifeand 10-Year Warranty.UNITED STATESAlabamaDealers LP Equipment Co. Dothan, ALTel: (334) 793-8293 or (800) 433-8925 Fax: (334) 671-3805ArkansasGas Equipment Co., Inc.Little Rock, ARTel: (501) 376-7141 or (800) 643-8222 Fax: (501) 376-0917CaliforniaTeeco Products, Inc.Irvine, CATel: (949) 261-6295 or (800) 854-3463 Fax: (949) 474-8663 or (888) 854-3463 Email: info@ Teeco Products, Inc. Sacramento, CATel: (916) 688-3535 or (800) 225-6621 Fax: (916) 689-1219 or (888) 225-6621 Email: info@ ColoradoGas Equipment Co. of Denver Wheat Ridge, COTel: (303) 422-3403 or (800) 525-2054 Fax: (303) 422-7842ConnecticutVictor/Divison of F.W. Webb Co. Hartford, CTTel: (860) 289-4223 or(800) 228-0508 (Inside CT)(800) 243-9360 (Outside CT)Fax: (800) 274-2004 or (860) 289-2457 Email: customerservice@ FloridaGas Equipment Co., Inc.Orlando, FLTel: (407) 843-6536 or (800) 821-0631 Fax: (407) 648-1546Peter Skop IndustriesOcala, FLTel: (352) 873-9641 or (800) 241-9880 Fax: (352) 873-9683Email: propane@ Tarantin Tank & Equipment Company Hastings, FL 32145Tel: (866) 837-1810Fax: (904) 692-1068GeorgiaGas Equipment Co., Inc. Lawrenceville, GATel: (770) 995-1131 or (800) 241-4155 Fax: (770) 995-1216Peter Skop IndustriesNorcross, GATel: (770) 449-4141 or (800) 241-9880 Fax: (800) 685-1052Email: propane@ IndianaGas Equipment Co., Inc.Indianapolis, INTel: (317) 541-1971 or (800) 241-1971Fax: (317) 541-8352IowaDealers LP Equipment Co.Davenport, IATel: (563) 386-3874 or (800) 544-2191Fax: (563) 386-3924KansasFairbank Equipment, Inc.Wichita, KSTel: (316) 943-2247 or (800) 666-5764Fax: (316) 943-6510Email: fairbank@KentuckyDealers LP Equipment Co.Louisville, KYTel: (502) 957-5630 or (800) 467-7541Fax: (502) 957-5631MichiganIPS Equipment, Inc.Byron, MITel: (810) 266-4687 or (800) 621-4137Fax: (810) 266-5554Email: ipsequip@MinnesotaLP Gas Equipment, Inc.St. Paul, MNTel: (651) 646-1177(800) 652-9072 (Inside MN)(800) 328-9222 (Outside MN)Fax: (651) 646-1676Email: lpgas@LPG & NH3 Supply, Inc.Buffalo, MNTel: (763)746-0540 or (800)328-0314.Fax: (763)746-0548MississippiDealers LP Equipment Co.Jackson, MSTel: (601) 353-2267 or (800) 844-0267Fax: (601) 353-2268Email: websales@MissouriGas Equipment Co., Inc.Kansas City, MOTel: (816) 746-9555 or (800) 821-5062Fax: (816) 746-8522Gas Equipment Co., Inc.Earth City, MOTel: (314) 298-8219 or (800) 423-4685Fax: (314) 298-7753NebraskaFairbank Equipment, Inc.Grand Island, NETel: (308) 381-4266 or (800) 441-7550Fax: (888) 505-2975 or (308) 384-9470New HampshireF.W. Webb CompanyAmherst, NHTel: (603) 882-1945Fax: (603) 883-4256Email: cps@Tarantin Tank and EquipmentBrentwood, NHTel: (603) 679-4617 or (800) 895-8265Fax: (603) 679-4605Email: tte@New JerseyTarantin Tank and EquipmentFreehold, NJTel: (732) 780-9340 or (800) 922-0724Fax: (732) 780-5173Email: tte@New YorkF.W. Webb CompanyClyde, NYTel: (315) 923-7819 or (800) 828-8824Fax: (315) 923-3794North CarolinaDealers LP Equipment Co.Hickory, NCTel: (828) 324-4469 or (800) 330-1738Fax: (828) 322-4466Gas Equipment Co., Inc.Fayetteville, NCTel: (910) 323-3747 or (800) 447-1625Fax: (910) 323-3879OklahomaFairbank Equipment, Inc.Chandler, OK877-258-2802405-258-2402Fax: 1-405-258-6704PennsylvaniaTarantin Tank and EquipmentCamp Hill, PATel: (717) 972-8750 or (888) 972-6323Fax: (717) 972-8737Email: tte@South DakotaTeeco Products, Inc.Rapid City, SDTel: (605) 342-2802 or (800) 843-8660Fax: (605) 342-4942 or (888) 843-8660Email: info@Fairbank Equipment, Inc.Yankton, SDTel: (605) 665-3041 or (800) 843-7913Fax: (605) 665-8737 or (888) 843-7913TennesseeDealers LP EquipmentMemphis, TNTel: (901) 386-8780 or (800) 238-3284Fax: (901) 386-8786Dealers LP EquipmentKnoxville, TNTel: (866) 384-4190Fax: (865) 212-3645TexasGas Equipment Co., Inc.Dallas, TXTel: (972) 241-2333 or (800) 821-1829Fax: (972) 620-1403Gas Equipment Co., Inc.Houston, TXTel: (713) 896-1077 or (800) 334-7816Fax: (713) 896-9299VirginiaGas Equipment Co., Inc.Richmond, VATel: (804) 226-7827 or (800) 368-4013Fax: (804) 226-8278Tarantin Tank & EquipmentRichmond, VATel: (804) 279-0203Fax: (804) 279-0206WashingtonTeeco Products, Inc.Auburn, WATel: (253) 735-0222 or (800) 426-9456Fax: (253) 735-1008 or (888) 426-9456Email: info@CANADAAlbertaDiversco Supply, Inc.Calgary, AlbertaTel: (403) 236-4494 or (800) 661-3139Fax: (403) 236-5561MaX-Quip Inc.Calgary, ABTel: 403-258-3685 or 866-629-7847Fax: 403-279-3099MaX-Quip Inc.Edmonton, ABTel: 780-442-3320 or 800-661-7770Fax: 780-451-5810British ColumbiaMax-Quip, Inc.Kelowna, BCTel: (604) 308-9430 or (866) 629-7847Fax: (604) 854-5450ManitobaMax-Quip, Inc.Winnipeg, MBTel: (204) 781-6574 or (866) 629-7847Diversco Supply Inc.Winnipeg, ManitobaPhone: 204-981-0881Fax: 204-284-0431New BrunswickDiversco Supply Inc.Moncton, New BrunswickPhone: 506-382-7376Fax: 506-382-7872OntarioDiversco Supply, Inc.Cambridge, OntarioTel: (519) 740-1210 or (800) 661-9955Fax: (519) 740-7303QuebecDiversco Supply, Inc.Pointe Claire, QuebecTel: (514) 693-0933 or (800) 465-3557Fax: (514) 693-0899SaskatchewanMax-Quip Inc.Saskatoon, SKTel: (306)-242-8900Fax: (306)-242-7878PRODUCTS。

顶级的研发中心完善的资质保证稳定的产品供应能力我们的优势Our advantageTop R & D centerPerfect qualification guarantee Stable product supply capacityBHM网站二维码 关于我们专注于研发与制造一体化集成水处理装备Focus on R & D and manufacturingIntegrated integrated water treatment equipment产品型号以反渗透的英文字头和装置的日产水量、规格代号和工艺级数组合而成。

拥有6种规格，单套装置标准产水量为20t/d、50t/d、100t/d、200t/d、500t/d、1000 t/d。

AIWS系列集装箱式反渗透装置分为SW型和BW型。

AIWS series container type reverse osmosis device is divided into SW type and BW type.With 6 specifications, the standard water production is 20t / d, 50t / d, 100t / d, 200t / d, 500t / d, 1000t / d.Product model to reverse osmosis English prefix and device Nissan water, specification code and the combination of the process level.Product two codeReverse osmosis module code产品代号（用英文字母的字头表示）Product code (in English alphabet)SW - suitable for high salinity type; BW - suitable for ordinary salt type.The scale of the unit is expressed in terms of standard daily water production, in m³ / dSW——适用于高含盐量型；BW——适用于普通含盐量型。

产品手册文字英\俄文翻译PRODUCTION CATALOGUE封面：产品手册目录：目录CATALOGUE、集团公司简介BRIEF INTRODUCTION、质量造就品牌、研发与创新、主要产品、未来产业园简介集团公司简介：新疆中泰化学（集团）股份有限公司是新疆维吾尔自治区重点支持的优势资源转换企业，属自治区国资委控股的上市公司。

主要从事聚氯乙烯树脂（PVC）、离子膜烧碱、工业盐、电石、焦炭等化工产品的生产和销售。

公司的产品广泛用于石油、化工、轻工、纺织、建材、国防等20余个大行业。

产品主要供应西北、华东、华南和华中地区，向西出口俄罗斯、哈萨克斯坦、乌兹别克斯坦以及巴基斯坦、印度、越南等中亚、南亚地区，并远销南美洲和非洲。

Xinjiang Zhongtai Chemical (Group) Co., Ltd is an important resource advantaged enterprise as the state focusing on supporting and it is a listed company by Autonomous Regions of the State-owned Assets Supervision holding. It mainly produces chemical products such as Polyvinyl Chloride Resin (PVC), Ion-Exchange Membrane Caustic Soda,Industrial Salt, Calcium Carbide and Coke. Its products widely used in more than 20 industries such as Petroluem Industry, Chemical Industry, Light Industry, Textile Industry, building materials and national defense. Its main domestic market is North-west China, East China, Southern part of China and Central China. It also exports products to Central Asia such as Russia, Kazakhstan , Uzbekistan from West Port of China, and to South Asia such as India, Viet Nam, Pakistan, and also find a good sale in South America and Africa.公司自2001年12月设立以来，连续10年保持年均40％以上的经济发展速度，生产能力已达到年产90万吨聚氯乙烯树脂、65万吨烧碱，跻身全国氯碱行业前三位。

LXCARDINAL LUXURY PACKAGE• Buffet Dinette with 32” Exterior TV • Frameless Automotive Windows • One Piece Molded Rear Cap • Hidden Hinge Cabinetry• 1.5 CU FT Convection Microwave • Ceiling Fan• Winegard 360+ (FM, TV Antenna W/ 4G & Wifi Extender Prep)• Dual Awnings with LED Light Strip (Most Models)• Firefly Command Center• Farmhouse 60/40 Kitchen Sink• Powered Theater Seat with Massage (N/A 390FBX)• Fiberglass Shower • Power Cord Reel• 24” Oven with 4-Burner Cast Iron Stove• Hardwood, Raised Panel Cabinet Doors and Slide Fascia • Flip-Up Night Stands • 17 CU FT 12V Refrigerator• Solid Surface Kitchen Countertops• Huge Pantry with Drawers (Most Models)LUXURY EXTENDED SEASONS CAMPING PACKAGE• 12v Heat Pads with Underbelly Ducted Heat • 35k BTU Furnace• 27k BTU A/C Output with Energy Management • Girard Tankless Water Heater• Exterior Ventilated Attic For Breathable Roof• Cadet Wall Mounted Heater With Circulation Fan (Bedroom)• Underbelly Armor ABS Underbelly PanelsCARDINAL LX FEATURE PACKAGES• (2) Ceiling Vents with Fan • Tufflex PVC Roof Membrane • Electric Fireplace in Living Area• Full Pass Thru Front Storage with Forced Air Heat • Sidewalls: 2” High Density Block Foam Insulation (R-9)• Roof: Fiberglass and Foil Insulation (ER38)• Floor: Residential and Foil Insulation (ER38) with 5/8” Tongue and Groove PlywoodLUXURY ESSENTIALS PACKAGE• Vacuum Bonded, Welded Aluminum Structure • Z-Frame Construction with Massive Storage • Flush Floor Galley Slide-Out• Massive Walk-In Closet with Stackable Washer/Dryer Prep • 100% Linoleum Interior• Quad, Lift-Assist Solid Step at Entry• Portable Ladder Prep Bracket For On-The-Go Portable Ladder • 7,000 Lb Axles with G-Rated Tires • Rear Observation Camera Prep • Aluminum Roof Wrap• Zero Floor Ducting (In-Wall And Cabinets)• TPMS (Tire Pressure Monitoring System)• Curt Rota-Flex Pin Box• Hydraulic 6 Point Automatic Leveling & Slide-Outs with Unity Pump • Road Armor Suspension with Wet Bolts And Shackles • Keyed Alike, Metal Slam Latch Baggage Doors • 2” Accessory Receiver• 32” Friction Hinged Entry Door• 72” x 80” King Bed with 110 Outlets On Sides2023 OFF THE GRID PACKAGECARDINAL LX CONSTRUCTIONEXTERIOR FEATURES1. Exterior Ventilated Attic for Breathable Roof2. PVC Roof Membrane w/ lifetime warranty3. 3/8” Plywood roof decking for Fully Walkable Roof Construction4. LCI Next Gen “Z” Frame 12” Main I-beam to 10” drop I-beam5. Front Windshield on select Floorplans6. 2” Thick Vacuum Bonded Main sidewalls and Slide Boxes7. Aluminum Framed Window, Door & Slide openings for Max Strength 8. Metal Slam Latch Compartment Doors 9. 32” x 76” Extra Large Entry Door10. 5/8” Tongue and Groove Plywood Main and Upper Floor Decking 11. Two Layers Batten insulation & Radiant Foil in Roof, Floor & Caps 12. Solid 4 Step Entry Steps Hinged to Lock in Door Frame 13. Forced Air Furnace Heat & 12V Tank Heaters in Subfloor 14. Road Armor Suspension15. Underbelly Armor for Best in Class Protection (4’ ABS Panels) 16. 7,000 lbs Easy Lube Dexter Axles w/ Never Adjust Brakes 17. G Range Tires Standard on All Cardinals 18. 6-Point Hydraulic Leveling 19. 21,000 lbs Pin Box20. Roof Mounted Solar Panel1234567891011121314151617181920CARDINAL LX FLOORPLANS320RLX360RLX380RLXSPECIFICATIONS 320RLX 360RLX 380RLX 390FBX Hitch Weight 2,105 lb.2,380 lb.2,555 lb.2,315 lb.UVW 11,379 lb.12,039 lb.12,294 lb.12,844 C 4,121 lb.3,461 lb.3,206 lb.2,656 lb.Length 36’ 1”41’ 9”42’ 2”43’ 3”Height 13’ 3”13’ 3”13’ 3”13’ 3”Fresh Water 60 gal.60 gal.60 gal.64 gal.Gray Water 45 gal.45 gal.84 gal.79 gal.Black Water 45 gal.45 gal.46 gal.79 gal.Awnings11’ & 12’13’ & 14’17’ & 11’11’ & 17’390FBX390FBX380RLX360RLXScan for additional specs, photos, videos, and more!GVWR (Gross Vehicle Weight Rating) - is the maximum permissible weight of the unit when fully loaded. It includes all weights, inclusive of all fluids, cargo, optional equipment and accessories. For safety and product performance do NOT exceed the GVWR.GAWR (Gross Axle Weight Rating) - is the maximum permissible weight, including cargo, fluids, optional equipment and accessories that can be safely supported by a combination of all axles.UVW (Unloaded Vehicle Weight)* - is the typical weight of the unit as manufactured at the factory. It includes all weight at the unit’s axle(s) and tongue or pin and LP Gas. The UVW does not include cargo, fresh potable water, additional optional equipment or dealer installed accessories.CCC (Cargo Carrying Capacity)** - is the amount of weight available for fresh potable water, cargo, additional option-al equipment and accessories. CCC is equal to GVWR minus UVW. Available CCC should accommodate fresh potable water (8.3 lbs per gallon). Before filling the fresh water tank, empty black and gray tanks for more cargo capacity.*Estimated Average based on standard build optional equipment. ** Estimated average based on standard build optional equipment. Values estimated at time of printing.Each Forest River RV is weighed at the manufacturing facility prior to shipping. A label identifying the unloaded vehicle weight of the actual unit and the cargo carrying capacity is applied to every Forest River RV prior to leaving our facili-ties. The load capacity of your unit is designated by weight, not by volume, so you cannot necessarily use all available space when loading your unit.All information contained in this brochure is believed to be accurate at the time of publication. However, during the model year, it may be necessary to make revisions and Forest River, Inc., reserves the right to make all such changes without notice, including prices, colors, materials, equipment and specifications as well as the addition of new models and the discontinuance of models shown in this brochure. Therefore, please consult with your Forest River, Inc., dealer and confirm the existence of any materials, design or specifications that are material to your purchase decision.©2023 Cardinal, a division of Forest River Inc., a Berkshire Hathaway company.Download our Forest River mobile app or visit our dynamic online manual to enhance your ownership experience. These interactive options provide incredible ease and insight into use, maintenance and enjoyment of your Forest River product.Ranging from “How-To” videos, pictures and illustrations of various components, systems and features,to fully searchable content and downloadable PDFs for individual component owner’s manuals, answers are always just a click away. View the online manual at /OnlineManual or download ourFREE app from the App Store or Google Play!320RLX。

A world of reliable rotation Alrik Danielson, President & CEOWelcome to Schweinfurt!Our vision: a world of reliable rotationStrategic prioritiesCreate and capture customer value Applicationdriven innovation World class manufacturing Cost competitivenessMaximize cash flow over timeDevelopments since we last metAutomotiveturn-aroundBalance sheet Pricing Focus on costs Application-specific performanceFactoryinvestmentsGrowth▪Fast and customer focused▪Refocused on the core business (8 divestments in 3 years)▪Strengthened financial position ▪Lowered cost level=> market share growth, record sales & record high profitSKF –in business for 111 years, fit and ready for the future!6.9%Organic growth:Target: 5%12.2%Operating margin:Target: 12%60%Net debt / equity:Target: <80%16.5%Return on capital employed:Target: 16%29.0%Net working capital:Target: 25%SKF’s value propositions around the rotating shaftCustomer valueInsightHindsight ForesightUnplanned downtime impacts cost and competitiveness ➢It’s not about predicting failure, it is alsoabout maximise production and plannedmaintenance➢Performance contracts are not new to SKF➢Our value propositions make us unique:Detect, Analyse & Fix➢Digitalization makes it exciting right now!➢Fee-based contracts enable us to capturevalue in a much better waySKF Digital PlatformSKF’s digital platform connects the value chainConnected devicesPartner networksAPIAsset statusAPIMachine health reports to SKF’s REP CenterAPISales leads to SKFAPISales leads to distributorsAPI Asset statusCustomer applicationSKF engineering tools and product developmentThe REP journey –from a customer’s perspectiveC u s t o m e r v a l u e c r e a t e d a n d c a p t u r e dManual processes; simplistic business modelsAutomated processes; Level 1TransactionalLevel 2Service ModelLevel 3PerformanceLevel 4Disruptive1980’s2000’sProgress follow-up▪ 4 million measuring points ▪Of which 1.5 million connected to our centers▪Strong growth –# measuring points more than doubled in two yearsREP centersSupporting further growth of REP businessSwedenGermanyREP in practice: Fibria pulp mills, Brazil© SKF GroupDevelopment of REP business models with FibriaBrazilian pulp manufacturer2000200720122018Performance-based service contractUnplanned downtime reduced by 50%Remote analysis introduction continues to increase productivityCloud-based wireless monitoring solutions4 s i t e s3 s i t e s2 s i t e s1 s i t e➢Four long-term contracts signed since 2000➢Fee based transaction model with bonus for improved output ➢x6 increase in annual revenue ➢Direct link between # of CoMo points; reduction in needed manpowerREP in practice: Big River Steel Hot Mill, Arkansas© SKF Group▪Monthly fee arrangement: ▪Bearings ▪Seals ▪CoMo▪Leveraging SKF technology to connect asset health to the supply chain improving reliability of component supply.Big River Steel✓Improve reliability✓Reduce unplanned downtime✓Reduce costsDigital solutions as an enabler in other industriesSKF Insight™ Rail▪Updated product launched in Q1 2018▪10+operators already using system in Europe, Asia and Australia ▪Enables new business models in the rail industry▪Partnership signed with train control systems supplierHighlights for the rest of the day▪Financial performance and importance in continuing to strengthen SKF▪Product development connected to REP and Product value proposition▪Automotive –turnaround success and future focus areas▪Manufacturing footprint and world-class technology development© SKF Group。

COMPONENTS AND FEATURES/OPTIONS COULD BE SUBSTITUTED, CHANGED OR ELIMINATED WITHOUT NOTICE DUE TOSUPPLY CHAIN ISSUESWE HAVE A DIVERSE, FEATURE-RICH, FLASHY ANDINNOVATIVE FLOOR PLAN LINEUP . WHETHER YOU ARE AMORE WEIGHT/LENGTH CONSCIOUS INDIVIDUAL, AWEEKEND WARRIOR, OR A MORE PERMANENTRESIDENT…WE HAVE WHAT YOU NEED.22SW-L 23DBH-L26DBH-L 26RL-L26RB-L30DBH-L 26RK-L28FK-L30RDB-L33BH-LSALES FEATURE GUIDEIn order to make purchasing our product easy…and we all like easy, we have divided our features up in to two differentcategories. First and foremost are the “Twelve Pack”features. These are our most important features as it pertains to othercompetitive brands. They set us apart and they will provide youwith the information you need to make a well educated buyingdecision.We don’t stop at just 12…this product is also packed with “Other Outstanding Features” . They are illustrated in the slides that follow. They are important and do a great job at illustrating why we are the fastest growing fifth wheel in North America.*Not all features may be available on all models. Recent market conditions may require componentchanges/substitutions/deletions –consult your sales representative for any exclusions*123456781491112141315“TWELVE PACK FEATURES” (EXTERIOR 6)1.One Piece Fiberglass, Gel-Coated, Front Cap with LED Strip Lights 2.Alpha “Step Above” Entry Step(s)3.Juice Pack Solar Power (50W Roof Panel, Series 27 Batt and Box, Batt Disconnect, Volt Meter, 30AMP Solar Charger.4.Wireless Rear Observation Camera 5.Power Tongue Jack 6.Tufflex PVC Roof Membrane with 20 Year Warranty OTHER OUTSTANDING EXTERIOR FEATURES 7.Dual 20# LP Bottles with Cover 8.100% Dark Tinted, Safety Glass Entry Door(s) with Friction Hinge, Viewing Window and Shade Prep 9.Exterior Backlit Speakers and TV Mount Located Under Awning 10.Tire Pressure Safety Sensors 11.Armored Underbelly Tank Enclosure and Forced Air to All Holding Tanks.12.Aluminum Rims with Radial Tires and Tire Pressure Safety Sensors.OTHER OUTSTANDING EXTERIOR FEATURES 13.Leash Latch Exterior Pet Safety Tether.14.Full Size Pass Thru Basement with LED Motion Lights, Slam Latches and Magnetic Holdbacks. 15.Outside Kitchen (Contents of Kitchen Vary by Model) with LP Quick Connect 16.Extendable Entry Grab Handle (Main Entry).17.20’ Awning Length (Excludes 22SW @ 18’)18.Fully Walkable Roof Decking (3/8”)19.Outside Shower with Hot and Cold Water 20.Quick Clean Waste Tank Sprayer 21.Convenience Light At Utility Center161718192021“TWELVE PACK FEATURES” (INTERIOR 6)1.Cannon, 12V High Efficiency, 11 Cu. Ft. Residential Refrigerator.2.Total Control Smart RV Technology.3.Smart Monitor Panel 4.Zebra Shades In main Living Area 5.Oversized 15,000 BTU Ducted Air Conditioner 6.200W Ceiling Mounted Sub Woofer 13OTHER OUTSTANDING INTERIOR FEATURES 7.High Rise Kitchen Faucet with Sprayer Head, Farm Style Sink and Hand Sanitizing Station.8.Backlit Range with Glass Cover 9.Removable Butcher Block Kitchen Backsplash.10.Double Port USB/110V Charging Station (Multiple Locations Throughout Units).11.Full Main Floor Lino Covering with Clean Sweep Design (No Heat Vents in Floor).12.5/8” Tongue and Groove Plywood Floor Decking.13.Pots and Pans Drawers with All Booth Style Dinettes 14.Seamless, High Impact, laminate Countertops.15.Laser Blue Ambient Interior Accent Lighting 16.Dual Zone, Bluetooth Stereo, Optimized for USB Flash Drives, IPOD’s and Other MP3 Players 17.5200 BTU Electric Fireplace with Multiple Heat Settings.87651011131415249121617OTHER OUTSTANDING INTERIOR FEATURES18.High Power, Multi-Speed Bath Fan.19.Oversized Shower with Skylight 20.Motion Sensing Night Light.21.Residential Size Bath Sink.22.Porcelain, Foot Flush Stool.23.Pleated Shades in Bedroom/Bunkroom 24.Dual Bed Side Night Stands with 110V Outlet and Dual Port USB.25.Deluxe Bedding Package with Oversized Pillow Shams 26.Individual reading lights.27.Full Under Bed Storage with Strut Lift Assist.28.LED Lighting Throughout Unit.2419211820222326252728THANK YOU!COMPONENTS AND FEATURES/OPTIONS COULD BE SUBSTITUTED, CHANGED OR ELIMINATED WITHOUT NOTICE DUE TOSUPPLY CHAIN ISSUES。

Polycom, Inc.1SAFETY AND REGULATORY NOTICES Polycom ® RealPresence ® Group SeriesThis document covers the following products:● Polycom ® RealPresence ® Group 300 System (Model: Group 300; Type: P001)● Polycom ® RealPresence ® Group 310 (Model: Group 310; Type: P001)● Polycom ® RealPresence ® Group 500 System (Model: Group 500; Type: P001)● Polycom ® RealPresence ® Group 700 System (Model: Group 700; Type: P002)● Polycom ® RealPresence ® Digital Brkout - Camera● Polycom ® RealPresence ® Digital Brkout - Codec● Polycom ® RealPresence ® Immersive Studio™ Camera (Model: P005)● Polycom ® EagleEye™ III (Model: MPTZ -9)● Polycom ® EagleEye™ IV 4x (Model: MPTZ -11)● Polycom ® EagleEye™ IV 12x (Model: MPTZ-10)● Polycom ® EagleEye™ IV -L● Polycom ® EagleEye™ Acoustic (Model: EPTZ -2)● Polycom ® EagleEye™ Digital Extender● Polycom ® EagleEye™ Producer● Polycom ® Touch Control● Polycom ® RealPresence Touch™ DeviceJuly 2019 | 3728-64323-014APlug Acts as Disconnect Device: The socket outlet to which this apparatus is connected mustbe installed near the equipment and must always be readily accessible.Follow existing safety instructions and observe all safeguards as directed. Installation must beperformed in accordance with all relevant national wiring rules.We recommend that you install an AC surge arrestor in the AC outlet to which this device is connected. This action will help to avoid damage to the equipment caused by local lightning strikes and other electrical surges.Class A Statements JapanChinaKoreaPolycom RealPresence Group 300 System (Model: Group 300; Type: P001)Polycom RealPresence Group 310 System (Model: Group 310; Type: P001)Polycom RealPresence Group 500 System (Model: Group 500; Type: P001)Polycom RealPresence Group 700 System (Model: Group 700; Type: P002)Polycom RealPresence Digital Brkout - CameraPolycom RealPresence Digital Brkout - CodecPolycom EagleEye III (Model: MPTZ-9)Polycom EagleEye IV 4x (Model: MPTZ-11)Polycom EagleEye IV 12x (Model: MPTZ-10)Polycom EagleEye Digital ExtenderPolycom EagleEye Producer Polycom RealPresence Touch주의또는경고문구(Caution or Warning)-콘센트에삽입된플러그에무거운물건을올리거나, 힘을가하지말것.-습기가많은장소및물이튈염려가있는장소에서사용하지말것.-젖은손으로플러그를만지지말것.-분해및개조하지말것.-기기근처에콘센트가있어야하고그콘센트에쉽게접근할수있어야할것.-제품을화기가까이에두지말것.TaiwanWarning!This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.Mexico Regulatory NoticesRussia Regulatory InformationCustoms Union (Russia, Belarus, Kazakhstan) Regulatory InformationInstallation InstructionsInstallation must be performed in accordance with all relevant national wireing rules.Battery UsageBefore its first use, charge the remote control battery. Insert the USB plug of the battery into a USB 2.0 port such as the one on your system. When the battery is charged, the LED light on the battery turns green.Do not short circuit batteries.Batteries should be treated and used in accordance with the battery manufacturer's guidance.Battery Caution and DisposalCAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.When the remote control battery has reached the end of its working life, remove it and take it to acollection point where it can be recycled or disposed of in an environmentally friendly manner. Donot dispose of the battery in a fire or in unsorted municipal waste.Details on recycling and disposal of batteries can be found at /batteries.Copyright Information© Polycom, Inc. 2019. All Rights Reserved.No part of this work may be copied for any purpose without the prior written permission of Polycom, Inc. Polycom, Inc. retains title to, and ownership of, all proprietary rights with respect to the software contained within its products. The software is protected by United States copyright laws and international treaty provision.Patent InformationThe accompanying product may be protected by one or more U.S. or foreign patents and/or pending patent applications held by Polycom, Inc.DisclaimerThis software is provided 'as is' with no explicit or implied warranties in respect of its properties, including, but not limited to, correctness and fitness for purpose.Trademark InformationPolycom®, the Polycom logo design, and the names and marks associated with Polycom’s products are trademarks and/or service marks of Polycom, Inc., and are registered and/or common-law marks in the United States and various other countries.All other trademarks are the property of their respective owners.。

实用标准视频会议系统安装施工工艺Group550安装操作手册二〇一三年九月目录一、设备环境安装要求 (4)1、硬件规格 (4)2、网络需求 (4)二、设备安装步骤 (5)1、 GROUP 550介绍-设备组成： (5)2、 GROUP 550介绍-背板连线示意： (5)3、实物展示 (5)4、物理连接 (6)三、加电测试 (15)1、设备开机 (15)2、电源指示灯状态 (15)3、主屏幕显示状态 (15)四、设备系统配置 (16)1、系统开机配置 (16)2、遥控器操作方法 (21)3、呼叫对方 (22)4、高级进阶设置 (23)五、系统功能测试 (28)1、终端点对点呼叫是否能够联通 (29)2、终端多点呼叫是否能够联通 (29)3、终端输出内容画面是否为1080P (29)4、终端画面和音频是否唇音同步 (29)5、终端双流输入是否正常 (29)六、设备常见故障处理 (29)1、遥控器的充电 (29)2、设置预设位和调用 (30)3、麦克风状态指示灯 (31)4、双流的发送 (31)5、诊断： (32)6、会议常见问题 (33)7、系统维护 (35)一、设备环境安装要求1、硬件规格2、网络需求视频会议系统传输使用专用IP网，由于MCU是整个视频会议系统的汇聚中心，为了保证视频会议画面清晰、声音逼真，并确保网与视频会议系统的安全、稳定运行，建议如下：1)为视频设备单独划分内网，使用单独Vlan。

2)MCU、录播服务器、会管服务器和设备管理服务器等设备需要连接在内网核心交换机上。

3)各个会议室视频终端到MCU之间尽量减少网络节点，避免受内网用户业务影响。

4)MCU、录播服务器、会管服务器和设备管理服务器及各个会议室视频终端均可与出资企业视频终端通信。

其间不经过防火墙、流量控制等设备。

如必需经过，需打开相关策略保证视频业务可通信。

二、设备安装步骤1、GROUP 550介绍-设备组成：称风实物图2、GROUP 550介绍-背板连线示意：3、实物展示4、物理连接4.1 摄像机连接HDCI镜头线-2头一样接口形状为梯形，对准镜头和终端插入4.2 双流输入双流输入口1（HDMI），如果笔记本同样具备HDMI接口，且连接距离不超过2米，可以接此接口，此接口具备将笔记本的视频和音频同时传输双流输入口2(VGA），最常用的接口，通用耳机接口且连接距离长，建议接此接口，如需要音频输出，请同时连接笔记本的耳机接口至“右侧接口”VGA接口（公头）4.3 音频输入接口为梯形，需对准mic ，两头一致后在插入原装MIC接口4.4 音频输出音频输出接口，双声道RCA接口（莲花）4.5 视频输出HDMI 输出1接口HDMI 输出2接口如果终端距离电视太远，也可以采用VGA 线缆输出第二路图像。

0304企业简介产品系列产品优势应用空间重点工程010302Company profile Product series Product advantages Application space Key projects p01-02p07-42施工说明Technical details p77-78p03-04工艺性能Process performance p05-06p43-67p68产品总览Product overview p69-76技术参数Technical parameters p79-80 4.5mm0506纯色 （釉面）Solid color(glazed)bSp05bbSp08a bSp03a bSp01bSp07abSp06a bSp05c bSp09bSp05e bSp10a 1000×2000mm / 1000×2400mm / 1000×3000mm 4.5mm every detail is coordinated, delicate design, make the whole space concise,bright, furniture and decoration layout, create such a delicate beautiful, warm andcomfortable space.每一处细节都协调统一，细腻的设计，使得整个空间简练、明亮，家具和装饰品布置其中，营造出如此精致美观、温馨舒适的空间。

Solid Color(GlAzed) / BSP09 / 1000×3000mmSolid Color(GlAzed) / BSP10A / 1000×3000mm 0708纯色（通体）pure color (full body)Pure Color (full Body) / BSf19+BSf29 /1000×3000mm bSf25bSf28bSf15bSf18bSf19bSf04bSf29bSf071000×2000mm / 1000×2400mm / 1000×3000mm 4.5mm 0910布纹wall paper WAll PAPer / BSz10 / 1000×3000mmWAll PAPer / BSz08 /1000×3000mm bSz08bSz09bSz10bSz051000×2000mm / 1000×2400mm / 1000×3000mm The excellent appearance of ceramic tiles with special materials to use, so thatthe texture of the space is very rich, but also reflects a variety of combined lifeexperience, adding special vitality to the space.外观效果出众的瓷砖搭配特别的材质来运用，使空间的质感非常丰富，也反映出多样结合的生活体验，为空间增添了特别的活力。

Field Modification Note075064500REFERENCE ECO: 194GEFFECTIVITY DATE: OCTOBER,2000 7500 NB OUTPUT MODULEA S S E MB L Y N U M B E R:671-4665-00Contacting Grass Valley GroupCopyright © Grass Valley Group. All rights reserved.This document may not be copied, in whole or in part, or otherwise reproduced, except as specifically permitted under U.S. copyright law, without the prior written consent of Grass Valley Group, P.O. Box 599000, Nevada City, CA 95959-7900 USA. GRASS VALLEY GROUP is a registered trademark and Grass Valley is a trademark of Grass Valley Group. All registered trademarks and trademarks are prop-erty of their respective holders. Grass Valley Group products are covered by U.S. and foreign patents, issued and pending. Product options and specifications subject to change without notice. The informa-tion in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Grass Valley Group. Grass Valley Group assumes no re-sponsibility or liability for any errors or inaccuracies that may appear in this publication.Region Voice FaxAddressWeb SiteNorth America (800) 547-8949530-478-4148(530) 478-3347Grass Valley Group P .O. Box 599000Nevada City, CA 95959-7900 USAPacific Operations+852-2585-6688Support: 852-2585-6579+852-2802-2996U.K., Europe, Asia, Middle East +44 1753 218 777+44 1753 218 757France +33 1 45 29 73 00Germany+49 221 1791 234+49 221 1791 235FMN 0750645007500 NB Output ModuleAssembly Number: 671-4665-00PurposeThis field modification corrects problems with the 7500 NB Outputmodule. It requires replacing firmware and cutting a leg on J5. The modulewill then provide the ability to invert channels before they are summed, thechannels can be summed in either 20 or 24 bit modes, and the digital valuewill not wrap.This modification applies only to 7500 NB Output modules with assemblynumber 671-4665-00.Parts ListPart Description Quantity163133201Firmware, 7500NB Output Module1Instructions1.Locate any 7500 NB output module which may need to be modifiedand remove it from the frame. The module can be removed with theframe powered up.2.Confirm that the module is a -00 version. The assembly number issilkscreened on the component side of the circuit board as illustrated inFigure 1. The dash version is written in the white box to the right of theassembly number.3.Locate the firmware, 163-1332-00, shown in Figure 1, and remove it.4.Install the new firmware, 163-1332-01.FMN 0750645001FMN 0750645002FMN 0750645007500 NB Output Module Assembly Number: 671-4665-00 FMN 0750645003FMN 0750645004FMN 0750645007500 NB Output Module Assembly Number: 671-4665-00 FMN 0750645005Grass Valley Group HeadquartersP.O. Box 599000075064500Nevada City, CA 95959-7900USAw w w.g r a s s v a l l e y g r o u p.c o m。

98139C REV. A (04/07)OVLMERQ*G OVLMSRQ*G OVLMESRQ*G OVLMSERQ*GUse with 97881C--Owners ManualMarblyte UnitsSUPPLEMENTAL SHEET DESCRIPTION 26990C 26988C 55836C 51544C 100322740560160270508640Not Req'd Not Req'd 11034622055010163745155016163730864045683C 45682C 10002334056016157080855061314C 50986C 55952C Not Req'd 70861C 55840C 55839C 27002C 27004C 28328C 15005C 40045C 27008C 70856C 70854C 50198C 51667C 28327C 28326C 22797C22799C26958C22795C26833C27026C55996C70683C70682C56092C70793C 12345678910111213141516171819202122232425262728293031323334353637NSP ART NO.Bottom Cover (OVL-S)Bottom Cover (OVL-E)Push Arm Actuator Bubbler Bubbler Gasket Strainer Plate Drain Gasket Packing Ring Drain Nut Friction Ring Drain Plug Waste Elbow (OVL-ER)Waste Elbow (OVL-SR)Waste Tube Gasket Slip Nut Regulator Regulator Holder Basin Blk Mrbl Basin Liner Screw # 10-24 x 2Top Plate - Actuator Bottom Plate - Actuator Arm w/Weldnuts (OVL-E)Arm w/Weldnuts (OVL-S)Regulator Mounting Bracket Nut - Retaining Nut Hex - UNPLTD Reaction Bracket Screw #10-24 x .38 PHMS Rod - Pivot Bushing Snap Bumper - Reg. Valve Assy Arm - Reg. Activating Arm - Reg. Adjustment Back Panel (OVL-ER)Back Panel (OVL-SR)Back Panel (OVL-SER)Back Panel (OVL-ESR)Bottom Panel (OVL-ER/SR)Bottom Panel (OVL-SER/ESR)Strainer Union - 1/4"Tee - 1/4"Poly Tubing - 1/4" (Cut To Length)Elbow - 1/4" x 90 Deg.ITEM NO.PARTS LISTCare and Maintenance of Halsey Taylor Marblyte FountainsMarblyte provides an extremely durable, nonporous surface which resists staining. Care is very simple.Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a soft cloth.Harsh abrasive cleaners are not required and should not be used.Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeperscratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite pad.To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products will keep the finish looking like new.91213118Arm Basin 105FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE 2222 CAMDEN COURTOAK BROOK, IL 60523630.574.3500PRINTED IN U.S.A.Drain Detail For Marblyte Fountains。

SDS # 410HBC S afety Latest Revision: June 2015 D ata Page 1 of 7 S heet Hobart Brothers Co. 1. PRODUCT AND COMPANY IDENTIFICATION:PRODUCT NAME: Electrodes, 6011, 1lb (H112216-R01, H112232-R01, H112244-R01)SUPPLIER: Hobart Brothers Co.2200 Corporate DriveTroy, OH 45373 U.S.A.Phone: 937-332-4000E-mail:**********************Website: EMERGENCY TELEPHONE NUMBER: 1-800-424-9300 (Chemtrec CCN11662)___________________________________________________________________________________2. HAZARD IDENTIFICATION:Emergency Overview: This product is normally not considered hazardous as shipped. Avoid eye contact or inhalation of dust from the product. When this product is used in a welding process, the most important hazards are welding fumes, heat, radiation and electric shock.Classification of the Substance/MixtureCLP/GHS Classification (1272/2008):Skin Irritation, Category 2Eye Irritation, Category 2ACarcinogenicity, Category 2EU Classification (67/548/EEC):Harmful (Xn), Irritant (Xi), Carcinogen Category 3, R36/38, R40Hazardous Classification per 29CFR 1910.1200 (Rev. July 1, 2012):Skin Irritation, Category 2Eye Irritation, Category 2ACarcinogenicity, Category 2Labelling:Symbols:Signal Word: WarningHazard Statements:H315–Causes skin irritation.H319–Causes serious eye irritation.H351–Suspected of causing cancer.Precautionary Statements:P201 –Obtain special instructions before use.P202 –Do not handle until all safety precautions have been read and understood.P264 –Wash skin and hair thoroughly after handling.P280 –Wear Protective gloves/eye protection/face protection.P281 –Use personal protective equipment as required.P302+P352 –IF ON SKIN: Wash with plenty of soap and water.P304+P340 –IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.P305+P351+P358 –IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.8675803S heet Hobart Brothers Co. P308+P313 –IF exposed or concerned: Get medical advice/attention.P332+P313 –IF skin irritation occurs: Get medical advice/attention.P337+P313 –IF eye irritation persists: Get medical advice/attention.P362 –Take off contaminated clothing and was before reuse.P405 –Store locked up.P501 –Dispose of contents/container in accordance with local/regional/national/international regulations.___________________________________________________________________________________(Xn)Not Dangerous Not Hazardous Not Hazardous((H315) SkinIrrit.. 2(H319) Eye Irrit..2A(H315) Skin Irrit.. 2(H319) Eye Irrit..2A(C ((H314) Skin(H335) STOT SE(H314) Skin Corr.1B(H335) STOT SE 3 Not Hazardous Not HazardousImportant This section covers the materials of which the products manufactured. The fumes and gases produced during normal use of this product are covered in section 10. The term “Hazardous” in “Hazardous Material” should be interpreted as a term required and defined in OSHA Hazard Communicatio n Standard 29CFR 1910-1200 and it does not necessarily imply the existence of hazard. The chemicals or compounds reportable by Section 313 of SARA are marked by the symbol #.___________________________________________________________________________________4. FIRST AID MEASURES:Inhalation: Remove to fresh air immediately or administer oxygen. Get medical attention immediately.Skin: Flush skin with large amounts of water. If irritation develops and persists, get medical attention.Eye: Flush eyes with water for at least 15 minutes. Get medical attention.Ingestion: Obtain medical attention immediately if ingested. Rinse mouth.Electric Shock: Disconnect and turn off the power. Use a nonconductive material to pull victim away from contact with live parts or wires. Immediately contact a physician.___________________________________________________________________________________5. FIRE-FIGHTING MEASURES:Suitable Extinguishing Media: Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. Welding arcs and sparks can ignite combustible and flammable materials. Use the extinguishing media recommended for the burning material and fire situation.Unsuitable Extinguishing Media:Not applicableSpecific Hazards Arising From Chemical: Arcs and sparks can ignite combustibles and flammable products. Iron Oxides, Sodium oxides, Silicon oxidesProtective Equipment: Fire fighters should wear complete protective clothing including self-contained breathing apparatus. ___________________________________________________________________________________6. ACCIDENTAL RELEASE MEASURES:Personal Precautions: Refer to section 8.Environment Precautions: Refer to section 13.Cleaning Measures: Solid objects may be picked up and placed into a container. Liquids or pastes should be scooped up and placed into a container. Wear proper protective equipment while handling these materials. Do not discard as refuse.___________________________________________________________________________________S heet Hobart Brothers Co. 7. HANDLING AND STORAGE:Precautions for Safe Handling: Handle with care to avoid stings or cuts. Wear gloves when handling welding consumables. Avoid exposure to dust. Do not ingest. Some individuals can develop an allergic reaction to certain materials. Retain all warning and identity labels.Conditions for Safe Storage: Store in dry place in closed packages. Keep separate from chemical substances like acids and strong bases, which could cause chemical reactions.___________________________________________________________________________________8. EXPOSURE CONTROLS/ PERSONAL PROTECTION:Engineering Controls:Avoid exposure to welding fumes, radiation, spatter, electric shock, heated materials and dust. Ensure sufficient ventilation, local exhaust, or both, to keep welding fumes and gases from breathing zone and general area. Keep work place and protective clothing clean and dry. Train welders to avoid contact with live electrical parts and insulate conductive parts. Check condition of protective clothing and equipment on a regular basis.Exposure limits: Use industrial hygiene equipment to ensure that exposure does not exceed applicable national exposure limits. The limits defined under section 3 can be used as guidance. Unless noted, all values are for 8 hour time weighted average. For information about welding fume analysis refer to section 10.Biological limits: No available dataPersonal protection:Respiratory protection: Use an air purifying dust respirator when welding or brazing in a confined space, or when local exhaust or ventilation is not sufficient to keep exposure values within safe limits.Hands protection: Wear appropriate gloves to prevent skin contact.EN 12477: Protection gloves for weldersType B gloves are recommended when high dexterity is required as for TIG welding, while type A gloves are recommended for other welding processes. The contact temp (ºC) is 100 and the threshold time (seconds) >15. Eyes protection:Welder’s helmet or face shield with colour absorbing lenses. Shield and filter to provide protection from harmful UV radiation, infra red and molten metal approved to standard EN379. Filter shade to be a minimum of shade 9.Skin protection: Heat-resistant protective clothing. Wear safety boots, apron, arm and shoulder protection. Keep protective clothing clean and dry. Clothing should be selected to suit the level, duration and purpose of the welding activity.S heet Hobart Brothers Co.___________________________________________________________________________________9. PHYSICAL AND CHEMICAL PROPERTIES:Appearance:Solid.Color: BrownOdour:OdourlessOdour Threshold: Not AvailablepH Value: Not AvailableMelting Point/Melting Range:: 1560 - 2000° F, 850 - 1100° CFreezing Point: Not AvailableBoiling Point/Boiling Range: Not AvailableFlash point: Not AvailableEvaporation Rate: Not AvailableSelf-in flammability:Not AvailableExplosion limits: Not AvailableVapour pressure: Not AvailableVapour density: Not AvailableDensity at 20ºC: Not AvailableRelative density: 6-9 g/cm3S heet Hobart Brothers Co. Solubility:Insoluble in water.Partition coefficient: Not AvailableAuto-ignition temperature: Not AvailableDecomposition temperature: Not AvailableOther Information:No available data.___________________________________________________________________________________10. STABILITY AND REACTIVITY:Chemical Stability: This product is stable under normal conditions.Hazardous Reactions: Contact with chemical substances like acids or strong bases cause generation of gas. Conditions to Avoid: Not applicable.Incompatible Materials: Reacts with acid.Hazardous Decomposition Products: When this product is used in a welding process, hazardous decomposition product would include those from volatilization, reaction or oxidation of the material listed in section 3 and those from the base metal and coating. The amount of fumes generated from this product varies with welding parameters and dimensions.Refer to applicable national exposure limits for fume compounds, including those exposure limits for fume compounds found in section 3. Manganese has a low exposure limit, in some countries that may be easily exceeded. Reasonably expected gaseous products would include carbon oxides, nitrogen oxides and ozone. Air contaminants around the welding area can be affected by the welding process and influence the composition and quality of fumes and gases produced.___________________________________________________________________________________11. TOXICOLOGICAL INFORMATION:Signs and Symptoms of Overexposure: Inhalation of welding fumes and gases can be dangerous to your health. Classification of welding fumes is difficult because of varying base materials, coatings, air contaminants and processes. The Internal Agency for Research on Cancer has classified welding fumes as possible carcinogenic to humans (Group 2B).Acute Effects: Overexposure to welding fumes may result in symptoms like metal fume fever, dizziness, nausea, dryness or irritation of the nose, throat or eyes. May cause sensitisation by skin contactChronic Effects:Overexposure to welding fumes may affect pulmonary function and eyes. Prolonged inhalation of titanium dioxide (Classified 2B by IARC) above safe exposure limits can possibly cause cancer.___________________________________________________________________________________12. ECOLOGICAL INFORMATION:Toxicity: Welding rods contain metals which are considered to be very toxic towards aquatic organisms. Finely divided welding rods are therefore considered harmful to aquatic organisms.Persistence and Degradability: The welding rods consist of elements that can not degrade any further in the environment.S heet Hobart Brothers Co. Bio accumulative Potential: Welding rods contain heavy metals which bio accumulates in the food chain. The following figures are the bio concentration factor (BCF) for the substances on their own.BCF:Iron, BCF: 140000Mobility in Soil: Welding rods are not soluble in water or soil. Particles formed by working welding rods can be transported in the air.Other Adverse Effects: In massive form, welding rods present no hazards to the aquatic environment.Welding materials could degrade into components originating from the materials used in the welding process. Avoid exposure to conditions that could lead to accumulation in soils or groundwater. Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.___________________________________________________________________________________13. DISPOSAL CONSIDERATIONS:Product:For product elimination, consult recycling companies or appropriate local authority.USA RCRA: This product is not considered hazardous waste if discarded. Residue from welding consumables and processes could degrade and accumulate in soils and groundwater.Package:May be disposed in approved landfills provided local regulations are observed.___________________________________________________________________________________14. TRANSPORT INFORMATION:UN-number: Welding rods are not classified as dangerous goods for transport and has no UN number.UN proper shipping name: Welding rods are not classified as dangerous goods for transport and has no UN proper shipping name.Transport hazard class: Welding rods are not classified as dangerous goods for transport.Packing group: There are not any special precautions with which a user should or must comply or be aware of in connection with transport or conveyance either within or outside premises.Environmental hazards: Welding rods are not environmentally hazardous according to the criteria of the UN Model Regulations (as reflected in the IMDG Code, ADR, RID and AND) and/or a marine pollutant to the IMDG Code.Special precautions for users: There are not any special precautions which a user should or must comply or be aware of in connection with transport or conveyance either within or outside premises of the welding rod.Transport in Bulk According to Annex III MARPOL 73/78 and the IBC Code: Welding rods in massive form do not subject under MARPOL 73/78 and the IBC Code. Not applicable – product is transported only in packaged form.____________________________________________________________________________________15. REGULATORY INFORMATION:Safety, health and environment regulations/legislation specific for the substance or mixture: Read and understand the manufacturer’s instructions, your employer’s safety practices and the health and safety instructions on the label. Observe a ny federal and local regulations. Take precautions when welding and protect yourself and others.Warning: Welding fumes and gases are hazardous to your health and may damage lungs and other organs. Use adequate ventilation.Electric shock can kill. Arc rays and sparks can injure eyes and burn skin. Wear correct hand, head, eye and body protection.Chemical safety assessment: NoUSA: Under the OSHA Hazard Communication Standard, this product is considered hazardous. This product contains or produces a chemical known to the state of California to cause cancer and birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5 et seq.) United States EPA Toxic Substance Control Act: All constituents of this product are on the TSCA inventory list or are excluded from listing.EPCRA/SARA Title III Toxic ChemicalsThe following metallic components are listed as SARA 313 “Toxic Chemicals” and potential subject to annual SARA reporting. See Section 3 for weight percentage.___________________________________________________________________________________16. OTHER INFORMATION:S heet Hobart Brothers Co. The information in this document is believed to be correct as of the date issued. However, no warranty is expressed to be implied regarding the accuracy or completeness of this information. This information and product are furnished on the condition that the person receiving them shall make his own determinations as to the suitability of the product for his particular purpose and on the condition that he assumes the risk of his use thereof.This Material Safety Data Sheet complies with the EC directives 91/155/EEC and 93/112/EEC, including modifications 2001/58/EC.Complies with OSHA Communication Standard 29 CFR 1910.1200 and Superfund Amendments and Reauthorization Act (SARA) of 1986 Public Law 99-499Hazard Statements:H314– Causes severe skin burns and eye damage.H315 –Causes skin irritation.H319– Causes serious eye irritation.H335 –May cause respiratory irritation.H351– Suspected of causing lung cancer.R-Phrases:R34 –Causes burns.R36/38 –Irritating to eyes and skin.R37 –Irritating to respiratory system.R40 –Limited evidence of a carcinogenic effect.S-Phrases:S26 –In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.S36/37/39 –Wear suitable protective clothing, gloves and eye/face protection.S45 –In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible). .End of the document.。

Dimensions: [mm]Scale - 3:1Test Setup:Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermany CHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODIva007.0032023-04-12DIN ISO 2768-1mDESCRIPTIONWE-SL2 SMT Common Mode LineFilter ORDER CODE744223BUSINESS UNIT STATUS PAGEB CT e m p e r a t u r eT pT LCautions and Warnings:The following conditions apply to all goods within the product series of WE-SL2 of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the Würth Elektronik technical soldering specification. All other profiles will void the warranty. •All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODIva007.0032023-04-12DIN ISO 2768-1mDESCRIPTIONWE-SL2 SMT Common Mode LineFilter ORDER CODE744223BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODIva007.0032023-04-12DIN ISO 2768-1mDESCRIPTIONWE-SL2 SMT Common Mode LineFilter ORDER CODE744223BUSINESS UNIT STATUS PAGE。

Dimensions: [mm]Scale - 4:174404084120BC74404084120T e m p e r a t u r eT pT L74404084120Cautions and Warnings:The following conditions apply to all goods within the product series of WE-LQS of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChrB002.0002023-03-27DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404084120SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChrB002.0002023-03-27DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404084120SIZE/TYPE BUSINESS UNIT STATUS PAGE。