PCB常见工程咨询中英文对照总结

PCB专业用语一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfacescopper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance。

PCB 中英文对照词汇一、综合词汇序号中文英文1印刷电路Printed circuit2印制线路Printed wiring3印刷板Printed board4印制板电路Printed circuit board(pcb)5印制线路板Printed wiring board(pwb)6印制元件Printed component7印制接点Printed contact8印制板装配Printed board assembly9板board10单面印制板Single-sided printed board(ssb) 11双面印制板Double-sided printed board(dsb) 12多层印制板Multilayer printed board(mlb) 13多层印制电路板Multilayer printed circuit board 14多层印制线路板Multilayer printed wiring board 15刚性印制板Rigid printed board16刚性单面印制板Rigid single-sided printed board 17刚性双面印制板Rigid double-sided printed board 18刚性多层印制板Rigid multilayer printed board 19挠性多层印制板Flexible multilayer printed board20挠性印制板Flexible printed board21挠性单面印制板Flexible single-sided printed board22挠性双面印制板Flexible double-sided printed board23挠性印制电路Flexible printed circuit(fpc)24挠性印制线路Flexible printed wiring25刚性印制线路Flex-rigid printed board 、 rigid-flexprinted board26刚性双面印制板Flex-rigid double-sided printed board、rigid-flex double-sided printed27刚性多层印制板Flex-rigid multilayer printed board、rigid-flex double-sided printed28齐平印制板Flush printed board29金属芯印制板Metal core printed board30金属基印制板Metal base printed board31多重布线印制板Mulit-wiring printed board32陶瓷印制板Ceramic substrate printed board33导电胶印制板Electroconductive paste printed board34模塑电路板Molded circuit board35模压印制板Stamped printed wiring board36顺序层压多层印制板Sequentially-laminated multilayer37散线印制板Discrete wiring board38微线印制板Micro wire board39积层印制板Build-up printed board40积层多层印板Build-up multilayer printed board (bum) 41积层挠性印制板Build-up flexible printed board42表面层合电路板Surface laminar circuit(slc)43埋入凸块连印制板B2it printed board44多层膜基板Mutil-layered film substrate(mfs) 45层间全内导通多层印Alivh multiplayer printed board制板46载芯片板Chip on board (cob)47埋电阻板Buried resistance board48母板Mother board49子板Daughter board50背板backplane51裸板Bare board52键盘板夹心板Copper-invar-copper board53动态挠性板Dynamic flex board54静态挠性板Static flex board55可断拼板Break-away planel56电缆cable57挠性扁平电缆Flexible flat cable (ffc)58薄膜开关Membrance switch59混合开关Hybrid circuit60厚膜Thick film61厚膜电路Thick film circuit62薄膜Thin film63薄膜混合电路Thin film hybrid circuit 64互连interconnection65导线Conductor trace line 66齐平导线Flush conductor 67传输线Transmission line 68跨交crossover69板边插头Edge-board contact 70增强板stiffener71基底Substrate72基板面Real estate73导线面Conductor side74元件面Component side 75焊接面Solder side76印制Printing77网格Grid78图形Pattern79导电图形Conductive pattern 80非导电图形Non-conductive pattern 81字符legend82标志mark二、基材序号中文英文1基材Base material2层压板Laminate3覆金属箔基材Metal-clad bade material4覆铜箔层压板Copper-clad laminate(ccl)5单面覆铜箔层压板Single-sided copper-clad laminate 6双面覆铜箔层压板Double-sided copper laminate 7复合层压板Composite laminate8薄层压板Thin laminate9金属芯覆铜箔层压板Metal core copper-clad laminate 10金属基覆铜层压板Metal base copper-clad laminate 11挠性覆铜箔绝缘薄膜Flexible copper-clad dielectric film 12基体材料Basis material13预浸材料Prepreg14粘结片Bonding sheet15预浸粘结片Preimpregnated bonding sheet 16环氧玻璃基板Epoxy glass substrate17加成法用层压板Laminate for additive process 18预制内层覆箔板Mass laminate panel19内层芯板Core material20催化板材Catalyzed board21涂胶催化层压板Adhesive-coated catalyzed laminate 22涂胶无催化层压板Adhesive-coated uncatalyzed laminate 23粘结层Bonding layer24粘结膜Film adhesive25涂胶粘剂绝缘薄膜Adhesive coated dielectric film26无支撑胶粘剂膜Unsupported adhesive film27覆盖层Cover layer28增强板材Stiffener material29铜箔面Copper-clad surface30去铜箔面Foil removal surface31层压板面Unclad laminate surface32基膜面Base film surface33胶粘剂面Adhesive face34原始光洁面Plate finish35粗面Matt finish36纵向Length wise direction37横向Cross wise direction38剪切板Cut to size panel39酚醛纸质覆铜箔板Phenolic cellulose paper copper-cladlaminates(phenolic paper ccl)40环氧纸质覆铜箔板Epoxide cellulose paper copper-cladlaminates(epoxy paper ccl)41环氧玻璃布基覆铜箔Epoxide woven glass fabric copper-clad 板laminate42环氧玻璃布纸复合覆Epoxide cellulose paper core glass cloth 铜箔板surfaces copper-clad laminate43环氧玻璃布玻璃纤维Epoxide non woven glass reinforced 复合覆铜箔板copper-clad laminate44聚酯玻璃布覆铜箔板Polyester wovenglass fabric copper-clad laminate45聚酰亚胺玻璃布覆铜Polyimide woven glass fabric copper-clad箔板laminate46双马来酰亚胺三嗪环Bismaleimide triazine epoxide woven 氧玻璃布覆铜板glass fabric copper-clad laminate47环氧合成纤维布覆铜Epoxide synthetic fiber copper-clad箔板laminates48聚四乙烯玻璃纤维覆Teflon fiber glass copper-clad laminate铜箔板49超薄型层压板Ultra thin laminate50陶瓷基覆铜箔板Ceramincs base copper-clad laminate 51紫外线阻挡型覆铜箔Uv blocking copper-clad laminates板三、基材的材料序号中文英文1 a 阶树脂a-stage resin2 b 阶树脂b-stage resin3 c 阶树脂c-stage resin4环氧树脂Epoxy resin5酚醛树脂Phenolic resin6聚酯树脂Polyester resin7聚酰亚胺树脂Polyimide resin8双马来酰亚胺三嗪树Bismaleimide-triazine resin脂9丙烯酸树脂Acrylic resin10三聚氰胺甲醛树脂Melamine formaldehyde resin 11多功能环氧树脂Polyfunctional epoxy resin 12溴化环氧树脂Brominated epoxy resin 13环氧酚醛Epoxy novolac14氟树脂fluroresin15硅树脂Silicone resin16硅烷silane17聚合物polymer18无定形聚合物Amorphous polymer19结晶现象Crystalline polamer20双晶现象dimorphism21共聚物copolymer22合成树脂synthetic23热固性树脂Thermosetting resin24热塑性树脂Thermoplastic resin25感光性树脂Photosensitive resin26环氧当量Weight per epoxy equipvalent(wpe) 27环氧值Epoxy value28双氰胺dicyandiamide29粘结剂binder30固化剂Curing agent31胶粘剂adesive32阻燃剂Flame retardant33遮光剂opaquer34增塑剂plasticizers35不饱和聚酯Unsatuiated polyster36聚酯薄膜polyester37聚酰亚胺薄膜Polyimide film(pi)38聚四氟乙烯Polytetrafluoetylene(ptfe)39聚四氟乙烯丙烯薄膜Perfluorinated ethylene-propylenecopolymer film(fep)40增强材料Reinforcing material41玻璃纤维Glass fiber42 E 玻璃纤维e-glass fiber43 D 玻璃纤维d-glass fiber44S 玻璃纤维s-glass fiber45玻璃布Glass fabric46非织布Non-woven fabric 47玻璃纤维垫Glass mats48纱线yarn49单丝filament50胶股strand51纬纱Weft yarn52经纱Warp yarn53但尼尔denier54经向Warp-wise55纬向Weft-wise 、 filling-wise 56织物经纬密度Thread count57织物组织Weave structure58平纹组织Plain structure59坏布Grey fabric60稀松织物Woven scrim61弓纬Bow of weave62断经End missing63缺纬Mis-picks64纬斜bias65折痕crease66云织waviness67鱼眼Fish eye68毛圈长Feather length69厚薄段mark70裂缝spilt71捻度Twist of yarn72浸润剂含量Size content73浸润剂残留量Size residue74处理剂含量Finish leval75浸润剂size76偶联剂Couplint agent77处理织物Finished fabric78聚酰胺纤维Polyarmide fiber79聚酯纤维非织布Non-woven polyester fabric 80浸渍绝缘纵纸Impregenating insulation paper 81聚芳酰胺纤维纸Aromatic polyamide paper 82断裂长Breaking length83吸水高度Height of capillary rise84湿强度保留率Wet strength retention85白度whitenness86陶瓷ceramics87导电箔Conductive foil88铜箔Copper foil89电解铜箔Electrodeposited copper foil (ed copperfoil)90压延铜箔Rolled copper foil91退火铜箔Annealed copper foil92压延退火铜箔Rolled annealed copper foil (ra copperfoil)93薄铜箔Thin copper foil94涂胶铜箔Adhesive coated foil95涂胶脂铜箔Resin coated copper foil(rcc)96复合金属箔Composite metallic material97载体搏Carrier foil98殷瓦invar99箔（剖面）轮廓Foil profile100光面Shiny side101粗糙面Matte side102处理面Treated side103防锈处理Stain proofing104双面处理铜箔Double treated foil四、设计序号中文英文1原理图Shematic diagram2逻辑图Logic diagram3印制线路布设Printed wire layout4布设总图Master drawing5可制造性设计Design-for-manufacturability6计算机辅助设计Computer-aided design(cad)7计算机辅助制造Computer-aided manufacturability(cim) 8计算机集成制造Computer integrat manufacturing 9计算机辅助工程Computer-aided engineering(cae) 10计算机辅助测试Computer-aided test (cat)11电子设计自动化Electric design automaton(eda) 12工程设计自动化Engineering design automaton(eda2) 13组装设计自动化Assemnly aided architecturaldesign(aaad) 14计算机辅助制图Computer aided drawing15计算机控制显示Computer controlled display(ccd) 16布局placement17布线routing18布图设计layout19重布rerouting20模拟simulation21逻辑模拟Logic simulation22电路模拟Circit simulate23时序模拟Timing simulation24模块化modularization25布线完成率Layout effeciency26机器描述格式Machine descriptionm format(mdf) 27机器描述格式数据库Mdf database28设计数据库Design database29设计原点Design origin30优化（设计）Optimization(design)31供设计优化坐标轴Predominant axis32表格原点Table origin33镜像Mirroring34驱动文件Drive file35中间文件Intermediate file36制造文件Manufacturing documentation 37队列支撑数据库Queue support database38元件安置component positioning 39图形显示Graphics display40比例因子Scaling factor41扫描填充Scan filling42矩形填充Rectangle filling43填充域Region filling44实体设计Physical design45逻辑设计Logic design46逻辑电路Logic design47层次设计Hierarchical design48自顶向下设计Top-down design49自顶向上设计Bottom-up design50线网net51数字化digitzing52设计规则检查Design rule checking53走（布）线路Router(cad)54网络表Net list55计算机辅助电路分析Computer-aided circuit analysis 56子线网Subnet57目标函数Objective function58设计后处理Post design processing(pdp) 59交互式制图设计Interactive drawing design 60费用矩阵Cost metrix61工程图Engineering drawing62方块框图Block diagram63迷宫Moze64元件密度Component density65巡回售货员问题Traveling salesman problem 66自由度Degrees freedom67入度Out going degree68出度Incoming degree69曼哈顿距离Manhatton distance70欧几里德距离Euclidean distance71网络Network72阵列Array73段Segment74逻辑Logic75逻辑设计自动化Logic design automation 76分线Separated time77分层Separated layer78定顺序Definite sequence79对准度registration80孔环Annular ring81公差Tolerance82同心Concentricity83样片coupon84变色discolorations85污点Stains86试样Specimen 87钻孔Drilling88剪裁Shearing 89切外型Routing90刮线Scoring91倒角Chamfering 92切空Blanking 93适应性suitability 94板弯Bow95板扭Twist96应力Stress97防焊膜Solder mask 98阻焊膜Solder resist 99文字标记Legend 100版本代字Revision letter 101料号Part No 102跳漏Skipping 103浮空Soda strawing 104流动Flow 105整平Leveling 106FPR First pass yield ‘。

PCB专业用语-英汉对照：一、综合词汇:1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board 10、单面印制板：single-sided printed board(ssb) 11、双面印制板：double-sided printed board(dsb) 12、多层印制板：mulitlayer printed board(mlb) 13、多层印制电路板：mulitlayer printed circuit board 14、多层印制线路板：mulitlayer prited wiring board 15、刚性印制板：rigid printed board 16、刚性单面印制板：rigid single-sided printed borad 17、刚性双面印制板：rigid double-sided printed borad 18、刚性多层印制板：rigid multilayer printed board 19、挠性多层印制板：flexible multilayer printed board 20、挠性印制板：flexible printed board 21、挠性单面印制板：flexible single-sided printed board 22、挠性双面印制板：flexible double-sided printed board 23、挠性印制电路：flexible printed circuit (fpc) 24、挠性印制线路：flexible printed wiring 25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed 27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board 28、齐平印制板：flush printed board 29、金属芯印制板：metal core printed board 30、金属基印制板：metal base printed board 31、多重布线印制板：mulit-wiring printed board 32、陶瓷印制板：ceramic substrate printed board 33、导电胶印制板：electroconductive paste printed board 34、模塑电路板：molded circuit board 35、模压印制板：stamped printed wiring board 36、顺序层压多层印制板：sequentially-laminated mulitlayer 37、散线印制板：discrete wiring board 38、微线印制板：micro wire board 39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board 42、表面层合电路板：surface laminar circuit (slc) 43、埋入凸块连印制板：b2it printed board 44、多层膜基板：multi-layered film substrate(mfs) 45、层间全内导通多层印制板：alivh multilayer printed board 46、载芯片板：chip on board (cob) 47、埋电阻板：buried resistance board 48、母板：mother board 49、子板：daughter board 50、背板：backplane 51、裸板：bare board 52、键盘板夹心板：copper-invar-copper board 53、动态挠性板：dynamic flex board 54、静态挠性板：static flex board 55、可断拼板：break-away planel 56、电缆：cable 57、挠性扁平电缆：flexible flat cable (ffc) 58、薄膜开关：membrane switch 59、混合电路：hybrid circuit 60、厚膜：thick film 61、厚膜电路：thick film circuit 62、薄膜：thin film 63、薄膜混合电路：thin film hybrid circuit 64、互连：interconnection 65、导线：conductor trace line 66、齐平导线：flush conductor 67、传输线：transmission line 68、跨交：crossover 69、板边插头：edge-board contact 70、增强板：stiffener 71、基底：substrate 72、基板面：real estate 73、导线面：conductor side 74、元件面：component side 75、焊接面：solder side 76、印制：printing 77、网格：grid 78、图形：pattern 79、导电图形：conductive pattern 80、非导电图形：non-conductive pattern 81、字符：legend 82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-cladlaminate 7、复合层压板：composite laminate 8、薄层压板：thin laminate 9、金属芯覆铜箔层压板：metal core copper-clad laminate 10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material 13、预浸材料：prepreg 14、粘结片：bonding sheet 15、预浸粘结片：preimpregnated bonding sheer 16、环氧玻璃基板：epoxy glass substrate 17、加成法用层压板：laminate for additive process 18、预制内层覆箔板：mass lamination panel 19、内层芯板：core material 20、催化板材：catalyzed board ,coated catalyzed laminate 21、涂胶催化层压板：adhesive-coated catalyzed laminate 22、涂胶无催层压板：adhesive-coated uncatalyzed laminate 23、粘结层：bonding layer 24、粘结膜：film adhesive 25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film 26、无支撑胶粘剂膜：unsupported adhesive film 27、覆盖层：cover layer (cover lay) 28、增强板材：stiffener material 29、铜箔面：copper-clad surface 30、去铜箔面：foil removal surface 31、层压板面：unclad laminate surface 32、基膜面：base film surface 33、胶粘剂面：adhesive faec 34、原始光洁面：plate finish 35、粗面：matt finish 36、纵向：length wise direction 37、模向：cross wise direction 38、剪切板：cut to size panel 39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl) 40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl) 41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates 42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates 43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates 44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates 45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates 46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates 47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates 48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates 49、超薄型层压板：ultra thin laminate 50、陶瓷基覆铜箔板：ceramics base copper-clad laminates 51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料:1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin 4、环氧树脂：epoxy resin 5、酚醛树脂：phenolic resin 6、聚酯树脂：polyester resin 7、聚酰亚胺树脂：polyimide resin 8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin 9、丙烯酸树脂：acrylic resin 10、三聚氰胺甲醛树脂：melamine formaldehyde resin 11、多官能环氧树脂：polyfunctional epoxy resin 12、溴化环氧树脂：brominated epoxy resin 13、环氧酚醛：epoxy novolac 14、氟树脂：fluroresin 15、硅树脂：silicone resin 16、硅烷：silane 17、聚合物：polymer 18、无定形聚合物：amorphous polymer 19、结晶现象：crystalline polamer 20、双晶现象：dimorphism 21、共聚物：copolymer 22、合成树脂：synthetic 23、热固性树脂：thermosetting resin 24、热塑性树脂：thermoplastic resin 25、感光性树脂：photosensitive resin 26、环氧当量：weight per epoxy equivalent (wpe) 27、环氧值：epoxy value 28、双氰胺：dicyandiamide 29、粘结剂：binder 30、胶粘剂：adesive 31、固化剂：curing agent 32、阻燃剂：flame retardant 33、遮光剂：opaquer 34、增塑剂：plasticizers 35、不饱和聚酯：unsatuiated polyester 36、聚酯薄膜：polyester 37、聚酰亚胺薄膜：polyimide film (pi) 38、聚四氟乙烯：polytetrafluoetylene (ptfe) 39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep) 40、增强材料：reinforcing material 41、玻璃纤维：glass fiber 42、 e玻璃纤维：e-glass fibre 43、 d玻璃纤维：d-glass fibre 44、 s玻璃纤维：s-glass fibre 45、玻璃布：glass fabric 46、非织布：non-woven fabric 47、玻璃纤维垫：glass mats 48、纱线：yarn 49、单丝：filament 50、绞股：strand 51、纬纱：weft yarn 52、经纱：warp yarn 53、但尼尔：denier 54、经向：warp-wise 55、纬向：weft-wise, filling-wise 56、织物经纬密度：thread count 57、织物组织：weave structure 58、平纹组织：plain structure 59、坏布：grey fabric 60、稀松织物：woven scrim 61、弓纬：bow of weave 62、断经：end missing 63、缺纬：mis-picks 64、纬斜：bias 65、折痕：crease 66、云织：waviness 67、鱼眼：fish eye 68、毛圈长：feather length 69、厚薄段：mark 70、裂缝：split 71、捻度：twist of yarn 72、浸润剂含量：size content 73、浸润剂残留量：size residue 74、处理剂含量：finish level 75、浸润剂：size 76、偶联剂：couplint agent 77、处理织物：finished fabric 78、聚酰胺纤维：polyarmide fiber 79、聚酯纤维非织布：non-woven polyester fabric 80、浸渍绝缘纵纸：impregnating insulation paper 81、聚芳酰胺纤维纸：aromatic polyamide paper 82、断裂长：breaking length 83、吸水高度：height of capillary rise 84、湿强度保留率：wet strength retention 85、白度：whitenness 86、陶瓷：ceramics 87、导电箔：conductive foil 88、铜箔：copper foil 89、电解铜箔：electrodeposited copper foil (ed copper foil) 90、压延铜箔：rolled copper foil 91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil 94、涂胶铜箔：adhesive coated foil 95、涂胶脂铜箔：resin coated copper foil (rcc) 96、复合金属箔：composite metallic material 97、载体箔：carrier foil 98、殷瓦：invar 99、箔（剖面）轮廓：foil profile 100、光面：shiny side 101、粗糙面：matte side 102、处理面：treated side 103、防锈处理：stain proofing 104、双面处理铜箔：double treated foil四、设计:1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae) 10、计算机辅助测试：computer-aided test.(cat) 11、电子设计自动化：electric design automation .(eda) 12、工程设计自动化：engineering designautomaton .(eda2) 13、组装设计自动化：assembly aided architectural design. (aaad) 14、计算机辅助制图：computer aided drawing 15、计算机控制显示：computer controlled display .(ccd) 16、布局：placement 17、布线：routing 18、布图设计：layout 19、重布：rerouting 20、模拟：simulation 21、逻辑模拟：logic simulation 22、电路模拟：circit simulation 23、时序模拟：timing simulation 24、模块化：modularization 25、布线完成率：layout effeciency 26、机器描述格式：machine descriptionm format .(mdf) 27、机器描述格式数据库：mdf databse 28、设计数据库：design database 29、设计原点：design origin 30、优化（设计）：optimization (design) 31、供设计优化坐标轴：predominant axis 32、表格原点：table origin 33、镜像：mirroring 34、驱动文件：drive file 35、中间文件：intermediate file 36、制造文件：manufacturing documentation 37、队列支撑数据库：queue support database 38、元件安置：component positioning 39、图形显示：graphics dispaly 40、比例因子：scaling factor 41、扫描填充：scan filling 42、矩形填充：rectangle filling 43、填充域：region filling 44、实体设计：physical design 45、逻辑设计：logic design 46、逻辑电路：logic circuit 47、层次设计：hierarchical design 48、自顶向下设计：top-down design 49、自底向上设计：bottom-up design 50、线网：net 51、数字化：digitzing 52、设计规则检查：design rulechecking 53、走（布）线器：router (cad) 54、网络表：net list 55、计算机辅助电路分析：computer-aided circuit analysis 56、子线网：subnet 57、目标函数：objective function 58、设计后处理：post design processing (pdp) 59、交互式制图设计：interactive drawing design 60、费用矩阵：cost metrix 61、工程图：engineering drawing 62、方块框图：block diagram 63、迷宫：moze 64、元件密度：component density 65、巡回售货员问题：traveling salesman problem 66、自由度：degrees freedom 67、入度：out going degree 68、出度：incoming degree 69、曼哈顿距离：manhatton distance 70、欧几里德距离：euclidean distance 71、网络：network 72、阵列：array 73、段：segment 74、逻辑：logic 75、逻辑设计自动化：logic design automation 76、分线：separated time 77、分层：separated layer 78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.1 7、圆形盘：round pad 8、方形盘：square pad 9、菱形盘：diamond pad 10、长方形焊盘：oblong pad 11、子弹形盘：bullet pad 12、泪滴盘：teardrop pad 13、雪人盘：snowman pad 14、 v形盘：v-shaped pad 15、环形盘：annular pad 16、非圆形盘：non-circular pad 17、隔离盘：isolation pad 18、非功能连接盘：monfunctional pad 19、偏置连接盘：offset land 20、腹（背）裸盘：back-bard land 21、盘址：anchoring spaur 22、连接盘图形：land pattern 23、连接盘网格阵列：land grid array 24、孔环：annular ring 25、元件孔：component hole 26、安装孔：mounting hole 27、支撑孔：supported hole 28、非支撑孔：unsupported hole 29、导通孔：via 30、镀通孔：plated through hole (pth) 31、余隙孔：access hole 32、盲孔：blind via (hole) 33、埋孔：buried via hole 34、埋/盲孔：buried /blind via 35、任意层内部导通孔：any layer inner via hole (alivh) 36、全部钻孔：all drilled hole 37、定位孔：toaling hole 38、无连接盘孔：landless hole 39、中间孔：interstitial hole 40、无连接盘导通孔：landless via hole 41、引导孔：pilot hole 42、端接全隙孔：terminal clearomee hole 43、准表面间镀覆孔：quasi-interfacing plated-through hole 44、准尺寸孔：dimensioned hole 45、在连接盘中导通孔：via-in-pad 46、孔位：hole location 47、孔密度：hole density 48、孔图：hole pattern 49、钻孔图：drill drawing 50、装配图：assembly drawing 51、印制板组装图：printed board assembly drawing 52、参考基准：datum referance。

一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board(pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit(fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board,rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board,rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board,rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board(bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit(slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board(cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable(ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate(ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer(cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core,glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent(wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film(pi)38、聚四氟乙烯：polytetrafluoetylene(ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film(fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise,filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil(ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil(ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil(rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation.(eda)12、工程设计自动化：engineering design automaton.(eda2)13、组装设计自动化：assembly aided architectural design.(aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display.(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format.(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization(design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router(cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing(pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction(track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole(pth)31、余隙孔：access hole32、盲孔：blind via(hole)33、埋孔：buried via hole34、埋/盲孔：buried/blind via35、任意层内部导通孔：any layer inner via hole(alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance整理自快点PCB学院。

PCB行业最常用术语之中英文对照(按字母检索)A/W (artwork) 底片Ablation 烧溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蚀accelerated test 加速试验acceleration 速化反应accelerator 加速剂acceptable 允收activator 活化液active work in process 实际在制品adhesion 附着力adhesive method 黏着法air inclusion 气泡air knife 风刀amorphous change 不定形的改变amount 总量amylnitrite 硝基戊烷analyzer 分析仪anneal 回火annular ring 环状垫圈;孔环anode slime (sludge) 阳极泥anodizing 阳极处理AOI ( automatic optical inspection ) 自动:光学检测applicable documents 引用之文件AQL sampling 允收水准抽样aqueous photoresist 液态光阻aspect ratio 纵横比(厚宽比)As received 到货时back lighting 背光back-up 垫板banked work in process 预留在制品base material 基材baseline performance 基准绩效batch 批beta backscattering 贝他射线照射法beveling 切斜边;斜边biaxial deformation 二方向之变形black-oxide 黑化blank controller 空白对照组blank panel 空板blanking 挖空blip 弹开blister 气泡;起泡blistering 气泡blow hole 吹孔board-thickness error 板厚错误bonding plies 黏结层bow ; bowing 板弯break out 从平环内破出bridging 搭桥;桥接BTO (Build To Order) 接单生产burning 烧焦burr 毛边(毛头)camcorder 一体型摄录放机carbide 碳化物carlson pin 定位梢carrier 载运剂catalyzing 催化catholic sputtering 阴极溅射法caul plate 隔板;钢板calibration system requirements 校验系统之各种要求center beam method 中心光束法central projection 集中式投射线certification 认证chamfer 倒角(金手指)chamfering 切斜边;倒角characteristic impedance 特性阻抗charge transfer overpotential 电量传递过电压chase 网框checkboard 棋盘chelator 蟹和剂chemical bond 化学键chemical vapor deposition 化学蒸着镀circumferential void 圆周性之孔破clad metal 包夹金属clean room 无尘室clearance 间隙coat 镀外表coating error 防焊覆盖错误coefficient of thermal expansion (CTE) 热澎胀系数cold solder joint 冷焊点cold-weld 金属粉末冷焊color 颜色color error 颜色错误compensation 补偿competitive performance 竞争力绩效complex salt 错化物complexor 错化物component hole 零件孔component side 零件面concentric 同心conformance 密贴性consumer products 消费性产品contact resistance 接触电阻continuous performance 连续发挥效能contract service 协力厂controlled split 均裂式conventional flow 乱流方式conventional tensile test 传统张力测试法conversion coating 转化层convex 突出coordinate list 数据清单copper claded laminates (CCL) 铜箔基板copper exposure 线路露铜copper mirror 镜铜copper pad 铜箔圆配copper residue (copper splash) 铜渣corrosion rate numbering 腐蚀速率计数系统corrosion resistance 抗蚀性coulombs law 库伦定律countersink 喇叭孔coupon 试样coupon location 试样点covering power 遮盖力CPU 中央处理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交联聚合cross talk 呼应作用crosslinking 交联crystal collection 结晶收集curing 聚合体current efficiency 电流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 学习循环cycle-time reduction 交期缩短date code 周期deburring 去毛头dedicated 专用型degradation 退变delamination 分层dent / pin hole 凹陷/ 针孔department of defense 国防部designation 字码简示法de-smear 除胶渣developing 显影dewetting 缩锡dewetting time 缩锡时间dimension error 外形尺寸错误dielectric constant 介质常数difficulty 困难度difunctional 双功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸与公差dirty hole 孔内异物discolor hole 孔黑;孔灰;氧化discoloration 变色disposable eyelet method 消耗性铆钉法distortion factor 尺寸变形函数double side 双面板downtime 停机时间drill 钻孔drill bit 钻头drill facet 钻尖切萷面drill pointer 钻尖重(研)磨机drilled blank board 已钻孔之裸板drilling 钻孔dry film 干膜ductility 延展性economy of scale 经济规模edge spacing 板边空地edge-board contact ( gold finger ) 金手指efficiency 能量效率electric test 电测electrical testing 电测;测试electrochemical machine ECM 电化学加工法electrochemical reactor 电化学反应器electroforming 电铸electroless plate 化学铜electroless-deposition 无电镀electropolishing 电解拋光electrorefining 电解精炼electrowinning 电解萃取elliptical set 椭圆形embrittlement 脆性entitlement performance 可达成绩效entrapment 电镀夹杂物epoxy 环氧树酯equipotential 电位线error data file 异常情形etch rate 蚀铜速率etchants 蚀刻液etchback 回蚀evaluation program 评估用程序exposure 曝光external pin method 外部插梢法eyelet hole 铆钉孔Eyeletting 铆眼fabric 网布failure 故障fast response 快速响应fault 瑕庛;缺陷fiber exposure 纤维显露fiber protrusion 纤维突出fiducial mark 光学点,基准记号filler 填充料film 底片filtration 过滤finished board 成品fixing 固着fixture 电测夹具(治具)flaking off 粹离flammability rating 燃性等级flare 喇叭形孔flat cable 并排电缆feedback loop 回馈循环first-in-first-out (FIFO) 先进先出flexible manufacturing system (FMS) 弹性制造系统flux 助焊剂foil distortion 铜层变形fold 空泡foreign include 异物foreign material 基材内异物free radical chain polymerization 自由基连锁聚合fully additive 加成法fully annealed type 彻底回火轫化之类形function 函数fundamental and basic 基本fungus resistance 抗霉性funnel flange 喇叭形折翼galvanized 加法尼化制程gap 钻尖分开gauge length 有效长度gel time 胶化时间general resist ink 一般阻剂油墨general 通论general industrial 一般性(电子)工业级geometrical levelling 几何平整glass transition temperature (Tg) 玻璃态转换温度Gold 金gold finger 金手指gold plating 镀金golden board 标准板gouges 刷磨凹沟gouging 挖破grain boundary 金属晶体之四边green 绿色grip 夹头ground plane 接地层ground plane clearance 接地空环hackers 骇客HAL ( hot air leveling ) 喷锡haloing 白边;白圈hardener 硬化剂hardness 硬度hepa filter 空气滤清器high performance industrial 高性能(电子)工业级high reliability 高可靠度high resolution 高分辨率high temperature elongation (HTE) 高温延展性铜箔high temperature epoxy (HTE) 高温树酯hit 击hole counter 数孔机hole diameter 孔径hole diameter error 孔径错误hole location 孔位hole number 孔数hole wall quality 孔壁品质hook 外弧hot dip 热浸法hull cell 哈氏槽hybrid 混成集成电路hydrogen bonding 氢键hydrolysis 水解hydrometallurgy 湿法冶金法image analysis system 影像分析系统image transfer 影像转移immersion gold 浸金(化镍金) immersion plating 浸镀法impedance 阻抗infrared reflow 红外线重熔inhibitor 热聚合抑制剂injection mold 射模ink 油墨innerlayer & outlayer 内外层insulation resistance 绝缘电阻intended position 应该在的位置intensifier 增强器intensity 强度inter molecular exchange 交互改变interconnection 互相连通ionic contaminants 离子性污染物ionic contamination testing 离子污染试验IPA 异丙醇5I : inspiration (启蒙)identification 确认计划目标implementation 改善方案information 数据internalization 制度化invisible inventory 无形的库存knife edges 刀缘Knoop 努普(硬度单位)kraft paper 牛皮纸laminar flow 层流laminate 基层板laminating 压合lamination 压合laminator 压膜机land 焊垫lay back 刃角磨损lay up 组合叠板layout 布线;布局lead screw 牵引螺丝leakage 漏电learning curve 学习曲线legend 文字标记leveling 平整levelling additive 平整剂levelling power 平整力life support 维系生命limiting current 极限电流line space 线距line width 线宽linear variable differential transformer(LVDL) 线性可变差动:转换器liquid 液状(态)liquid crystal resins 液晶树脂liquid photoimageable solder resist ink 液态感光防焊油墨liquid photoresist ink 液态光阻剂油墨lot size 批量lower carrier 底部承载板mechanical plating 机祴镀法machine scrub 刷磨清洁法macrothrowing power 巨分布力margin 钻头刃带market share 市场占有率marking error 文字错误masked leveling 儰装平整mass lamination 大型压板mass transfer 质量传送效应mass transfer overpotential 质量传递过电压mass transportation 质传master drawing 主图;蓝图material use factor 材料使用率mealing 泡点;白点memory 记忆装置meniscograph solderability measurement 新月型焊锡效果microetch 微蚀microetching 微蚀microfocus 微焦距microfocus system 微焦距系统microprofile 微表面microsectioning 微切片法microthrowing power 微分布力migration 迁移mini-tensile tester 迷你拉力测试仪mis hole location 孔位错误misregistration 焊锡面与零件面对位偏差misregsitration 对不准moisture and insulation resistance test 湿气与绝缘电阻试验molded circuit board (MCB) 模制电路板monoethanal amine 单乙醇氨monohydrate state 水化物monomer 单分子膜;单体mouse bite 锯齿;蚀刻缺口msec 毫秒muffle furnace 高温焚火炉multichip 超大IC型(多芯片模块)mylar 保护膜nail head 钉头NC drill 数字钻孔机negative etchback 反回蚀negative film 负片negative rake angle 负抠耙角network 回路;网络neutralization 中和nick 缺口nickel 镍nodule 铜瘤;瘤粒no flow resin 不流树脂noise 噪声nominal 标示nominal dimension 标定长度nominal gel time 标示胶性时间nominal resin content 标示胶含量nominal resin flow 标示胶流量nominal scaled flow thickness 标示比例流量厚度OA equip 办公室自动:化设备obsolescence factor 报废因素OEM 原设备制造商offset-list 补偿数据清单ohmmeter 欧姆计open 断路open circuits 断路open short testing 断短路测试opening 开口original art work (A/W) 原稿底片Others 其它outgrowth 增出over design 牛刀杀鸡overlap 钻尖重叠overlay entry 盖板overpotential 过电压oxidation 氧化oxide treatment 黑化处理oxided cytochrome 氧化性之细包色素oxygen evolution 氧气发生反应packed bed 充填床式pad 锡垫;圆配pad copper exposure pad露铜panel 小型板面;母板panel plating 一次铜电镀parasitic 寄生的part no. 料号pattern plating 二次铜电镀PCB ( print circuit board ) 印刷电路板pcs 片peel strength 抗撕强度peeling off 剥离(剥落) performance specification 性能规范permittivity 透电率perspectives on experience 经验透视PET 聚酯photodiode detector 发光二极管侦测器photo initiator 感光启始剂photoresist 光阻phototool 光具(指工作底片)piece 子板面pinceton applied research 腐蚀测定仪pink ring 粉红圈pit 凹点pitch 脚距planar 平面plating 电镀plating exposure 下镀层露出plug gauge 插规plug hole 孔塞PNL (panel) 排板polar-polar interaction 极性之间的吸力polyester 聚酯类polyglycols 聚乙二醇polyimide 聚亚醯氨poor bevelling 磨边加工引起突起,剥离poor drill 孔形不良poor HAL 喷锡不良poor marking 字体不良poor pad 锡垫不良poor printed 印刷偏差poor solderability 焊锡性不良poor touch-up 补线不良position control system 位置控制系统positive rake angle 正抠耙角power curve model 幕次曲线模式practice 工艺惯例preferred 良好premature tearing 提前撕裂prepolymer 预聚合物prepreg 胶片pre-process ( front-end) 制前press 压床press cycle 压合周期primary current distribution 一次电流分布primary 主要product lifetimes 生命周期product process 制程promoter 促进剂protocal 初步资料prussic acid 普鲁士酸PTF-based process 厚膜糊法PTH (plating though hole) 导通孔pull away 拉开pumice 浮石粉pumice scrub 喷砂清洁法pyrometallurgy 火烧法冶炼QC ( quality control) 品管QFP (quad flat pack ) 扁方型封装体qualification inspection 资格审查检验qualification testing 资格检定quality classification 品质等级quantitative 计量式测试rack 挂架radiometer 能量剂rake angle 抠耙角RAM [Random Access Memory 随机存取内存real time 关键时刻recessed trace process 凹槽线路法recovery tank 回收槽reduction 还原re-eninforcement 强化refraction 折光率reinforcement style 补强材料的型式register mark 对位用标记registration hole 对位孔registration pattern 长方形铜地REJ ( reject ) 退货;拒收rejectable 拒收release agent 脱模剂relief angle 浮离角remark 备注repair 修理resin content 树脂含量(胶含量)resin flow 胶流量resin flow percentage 树脂流量之百分率resin recession 树脂下陷resin smear 胶渣resist strippers 剥干膜剂resistor network 排列电阻resolution 解像度return on assets 资产报酬率reversibility 可逆性rework 重工rosin 天然松香rotating cylinder 旋转圆柱形roughtness 孔壁粗糙;粗慥routing 切外形,成型routing bit 铣刀runout 偏转S/L on hole 孔内沾文字S/M ( solder mask ), S/L 防焊文字S/M (solder mask) 防焊S/M error 防焊种类错误S/M on hole 孔内绿漆salt spray test 盐水喷雾试验sampling size 抽样数scope 范围scored 刻痕scoring 枢槽;刮线scrap 废框scratches 刮伤screen printing 网版印刷scum 透明残膜sealing 封孔处理secondary 次要semi-additive 半加成法sensitize 敏化sensitizer 敏化液separator 钢隔板sequential lamination 渐成式压法serrated edges 毛边shatter 破碎short 短路shunt 分路silane treatment 硅烷处理silicone coupling agent 硅烷偶合剂silk screen 文字印刷simulator 仿真器single axis 单轴sizing 底片之伸缩补偿skip 漏印skip printing 跳印;漏印sliver 丝条slot 开槽slotting 开槽SMD ( surface mount device ) 表面黏着组件smear 胶渣SMT ( surface mount technology )表面黏着技术sodium carbonate monohydrate 结晶水碳酸钠soft tooling 软性工具solder 焊锡; 锡铅solder bridge 锡桥solder bump 锡突solder float 漂锡solder mask adhesion 绿漆附着力solder on G/F 金手指沾锡solder on trace 线路沾锡solder plug 锡塞solder side 焊锡面solderability 焊锡性solid carbide 实质碳化物spacing 间距spacing nonenough 间距不足SPC ( Statistical Process Control ) 统计生管specification 规范special considerations 特别考虑spin coating 旋转涂布spindle 钻轴spiral contractometer 螺旋收缩仪spot face 铣靶spray coating 喷涂Squeegee 刮刀stacking structure 叠板结构stamping 冲压standard hydraulic lamination标准液压法standardizing 标准化starvation 缺胶step tablet 格片数stock option 认股选择权strain 应度strength 强度stressmeter 应力计subtractive 减除法surface convex 表面突起surface examination 表面检查surface insulation resistance (SIR) 表面绝缘电阻surface mount 表面黏着方式surface roughness 表面粗慥度surges 突波switch circuit 开关线路tab 金手指tack free 不黏taped hole gauge 锥形孔规target hole 靶孔task force 任务编组tensile strength 抗拉强度tensile stress 张性应力tent 浮盖terms and definitions 术语与定义termination load 抗匹配负载test circuit 测试线路test method 试验方法test point 测试点thermal shock 热震荡试验thermal stress 热应力试验thermistor 热电感应式thermo cycling 热循环试验theoretical cycle time 理论性周期时间thickness 厚度time to market 上市时机thickness distribution 厚度分布thief 补助阴极thin core 薄基板;内层板throwing power 分布力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之负载total quality program 全面的品质计划toughness 坚度trace error 线路错误trace nick & pin hole 线路缺口及针孔trace peeling 线路剥离trace pin-hole 线路针孔trace surface roughness 线路表面粗糙tarnish and oxide resist 抗污抗氧化剂transmittance 透光度trim line 裁切线true levelling 真平整true position 真正位置的孔;真位twist 板翘type 种类umbra 本影undercut 侧蚀uneven coating 喷锡厚镀不平整universal 万用型universal tensile tester 万用拉力试验机universal tester 泛用型测试机upper carrier 顶部承载钢uptime 稼动:时间vacuum deposition 真空蒸镀法vacuum hydraulic lamination真空液压法vaporizer 气化室V-cut V形槽vertical microsection 垂直微切片via hole 导通孔visible inventory 有形的库存vision inspection 目视检查V oid 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 随身听warehouse 仓库warp 板弯warp , warpage 板弯water absorption 吸水性wear resistance 耐磨度weave exposure 纤纹显露weave texture 织纹隐现wedge angle 契尖角week 周wet chemistry 湿式化学制程wet film 湿膜wet lamination 湿膜压膜法wet process 湿制程wetting 沾锡wetting balance 沾锡平衡法wicking 渗铜;渗入;灯蕊效应width 宽度width reduce 线细width-to-thickness ratio 宽度与厚度的比值window 操作范围work-in-process 在制品work order 工单working film 工作片working master 工作母片year 年yellow 金黄色yield 良率。

PCB行业最常用术语之中英文对照(按字母检索)A/W (artwork) 底片Ablation 烧溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蚀accelerated test 加速试验acceleration 速化反应accelerator 加速剂acceptable 允收activator 活化液active work in process 实际在制品adhesion 附着力adhesive method 黏着法air inclusion 气泡air knife 风刀amorphous change 不定形的改变amount 总量amylnitrite 硝基戊烷analyzer 分析仪anneal 回火annular ring 环状垫圈;孔环anode slime (sludge) 阳极泥anodizing 阳极处理AOI ( automatic optical inspection ) 自动:光学检测applicable documents 引用之文件AQL sampling 允收水准抽样aqueous photoresist 液态光阻aspect ratio 纵横比(厚宽比)As received 到货时back lighting 背光back-up 垫板banked work in process 预留在制品base material 基材baseline performance 基准绩效batch 批beta backscattering 贝他射线照射法beveling 切斜边;斜边biaxial deformation 二方向之变形black-oxide 黑化blank controller 空白对照组blank panel 空板blanking 挖空blip 弹开blister 气泡;起泡blistering 气泡blow hole 吹孔board-thickness error 板厚错误bonding plies 黏结层bow ; bowing 板弯break out 从平环内破出bridging 搭桥;桥接BTO (Build To Order) 接单生产burning 烧焦burr 毛边(毛头)camcorder 一体型摄录放机carbide 碳化物carlson pin 定位梢carrier 载运剂catalyzing 催化catholic sputtering 阴极溅射法caul plate 隔板;钢板calibration system requirements 校验系统之各种要求center beam method 中心光束法central projection 集中式投射线certification 认证chamfer 倒角(金手指)chamfering 切斜边;倒角characteristic impedance 特性阻抗charge transfer overpotential 电量传递过电压chase 网框checkboard 棋盘chelator 蟹和剂chemical bond 化学键chemical vapor deposition 化学蒸着镀circumferential void 圆周性之孔破clad metal 包夹金属clean room 无尘室clearance 间隙coat 镀外表coating error 防焊覆盖错误coefficient of thermal expansion (CTE) 热澎胀系数cold solder joint 冷焊点cold-weld 金属粉末冷焊color 颜色color error 颜色错误compensation 补偿competitive performance 竞争力绩效complex salt 错化物complexor 错化物component hole 零件孔component side 零件面concentric 同心conformance 密贴性consumer products 消费性产品contact resistance 接触电阻continuous performance 连续发挥效能contract service 协力厂controlled split 均裂式conventional flow 乱流方式conventional tensile test 传统张力测试法conversion coating 转化层convex 突出coordinate list 数据清单copper claded laminates (CCL) 铜箔基板copper exposure 线路露铜copper mirror 镜铜copper pad 铜箔圆配copper residue (copper splash) 铜渣corrosion rate numbering 腐蚀速率计数系统corrosion resistance 抗蚀性coulombs law 库伦定律countersink 喇叭孔coupon 试样coupon location 试样点covering power 遮盖力CPU 中央处理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交联聚合cross talk 呼应作用crosslinking 交联crystal collection 结晶收集curing 聚合体current efficiency 电流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 学习循环cycle-time reduction 交期缩短date code 周期deburring 去毛头dedicated 专用型degradation 退变delamination 分层dent / pin hole 凹陷/ 针孔department of defense 国防部designation 字码简示法de-smear 除胶渣developing 显影dewetting 缩锡dewetting time 缩锡时间dimension error 外形尺寸错误dielectric constant 介质常数difficulty 困难度difunctional 双功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸与公差dirty hole 孔内异物discolor hole 孔黑;孔灰;氧化discoloration 变色disposable eyelet method 消耗性铆钉法distortion factor 尺寸变形函数double side 双面板downtime 停机时间drill 钻孔drill bit 钻头drill facet 钻尖切萷面drill pointer 钻尖重(研)磨机drilled blank board 已钻孔之裸板drilling 钻孔dry film 干膜ductility 延展性economy of scale 经济规模edge spacing 板边空地edge-board contact ( gold finger ) 金手指efficiency 能量效率electric test 电测electrical testing 电测;测试electrochemical machine ECM 电化学加工法electrochemical reactor 电化学反应器electroforming 电铸electroless plate 化学铜electroless-deposition 无电镀electropolishing 电解拋光electrorefining 电解精炼electrowinning 电解萃取elliptical set 椭圆形embrittlement 脆性entitlement performance 可达成绩效entrapment 电镀夹杂物epoxy 环氧树酯equipotential 电位线error data file 异常情形etch rate 蚀铜速率etchants 蚀刻液etchback 回蚀evaluation program 评估用程序exposure 曝光external pin method 外部插梢法eyelet hole 铆钉孔Eyeletting 铆眼fabric 网布failure 故障fast response 快速响应fault 瑕庛;缺陷fiber exposure 纤维显露fiber protrusion 纤维突出fiducial mark 光学点,基准记号filler 填充料film 底片filtration 过滤finished board 成品fixing 固着fixture 电测夹具(治具)flaking off 粹离flammability rating 燃性等级flare 喇叭形孔flat cable 并排电缆feedback loop 回馈循环first-in-first-out (FIFO) 先进先出flexible manufacturing system (FMS) 弹性制造系统flux 助焊剂foil distortion 铜层变形fold 空泡foreign include 异物foreign material 基材内异物free radical chain polymerization 自由基连锁聚合fully additive 加成法fully annealed type 彻底回火轫化之类形function 函数fundamental and basic 基本fungus resistance 抗霉性funnel flange 喇叭形折翼galvanized 加法尼化制程gap 钻尖分开gauge length 有效长度gel time 胶化时间general resist ink 一般阻剂油墨general 通论general industrial 一般性(电子)工业级geometrical levelling 几何平整glass transition temperature (Tg) 玻璃态转换温度Gold 金gold finger 金手指gold plating 镀金golden board 标准板gouges 刷磨凹沟gouging 挖破grain boundary 金属晶体之四边green 绿色grip 夹头ground plane 接地层ground plane clearance 接地空环hackers 骇客HAL ( hot air leveling ) 喷锡haloing 白边;白圈hardener 硬化剂hardness 硬度hepa filter 空气滤清器high performance industrial 高性能(电子)工业级high reliability 高可靠度high resolution 高分辨率high temperature elongation (HTE) 高温延展性铜箔high temperature epoxy (HTE) 高温树酯hit 击hole counter 数孔机hole diameter 孔径hole diameter error 孔径错误hole location 孔位hole number 孔数hole wall quality 孔壁品质hook 外弧hot dip 热浸法hull cell 哈氏槽hybrid 混成集成电路hydrogen bonding 氢键hydrolysis 水解hydrometallurgy 湿法冶金法image analysis system 影像分析系统image transfer 影像转移immersion gold 浸金(化镍金) immersion plating 浸镀法impedance 阻抗infrared reflow 红外线重熔inhibitor 热聚合抑制剂injection mold 射模ink 油墨innerlayer & outlayer 内外层insulation resistance 绝缘电阻intended position 应该在的位置intensifier 增强器intensity 强度inter molecular exchange 交互改变interconnection 互相连通ionic contaminants 离子性污染物ionic contamination testing 离子污染试验IPA异丙醇5I : inspiration (启蒙)identification 确认计划目标implementation 改善方案information 数据internalization 制度化invisible inventory 无形的库存knife edges 刀缘Knoop 努普(硬度单位)kraft paper 牛皮纸laminar flow 层流laminate 基层板laminating 压合lamination 压合laminator 压膜机land 焊垫lay back 刃角磨损lay up 组合叠板layout 布线;布局lead screw 牵引螺丝leakage 漏电learning curve 学习曲线legend 文字标记leveling 平整levelling additive 平整剂levelling power 平整力life support 维系生命limiting current 极限电流line space 线距line width 线宽linear variable differential transformer(LVDL) 线性可变差动:转换器liquid 液状(态)liquid crystal resins 液晶树脂liquid photoimageable solder resist ink 液态感光防焊油墨liquid photoresist ink 液态光阻剂油墨lot size 批量lower carrier 底部承载板mechanical plating 机祴镀法machine scrub 刷磨清洁法macrothrowing power 巨分布力margin 钻头刃带market share 市场占有率marking error 文字错误masked leveling 儰装平整mass lamination 大型压板mass transfer 质量传送效应mass transfer overpotential 质量传递过电压mass transportation 质传master drawing 主图;蓝图material use factor 材料使用率mealing 泡点;白点memory 记忆装置meniscograph solderability measurement 新月型焊锡效果microetch 微蚀microetching 微蚀microfocus 微焦距microfocus system 微焦距系统microprofile 微表面microsectioning 微切片法microthrowing power 微分布力migration 迁移mini-tensile tester 迷你拉力测试仪mis hole location 孔位错误misregistration 焊锡面与零件面对位偏差misregsitration 对不准moisture and insulation resistance test 湿气与绝缘电阻试验molded circuit board (MCB) 模制电路板monoethanal amine 单乙醇氨monohydrate state 水化物monomer 单分子膜;单体mouse bite 锯齿;蚀刻缺口msec 毫秒muffle furnace 高温焚火炉multichip 超大IC型(多芯片模块)mylar 保护膜nail head 钉头NC drill 数字钻孔机negative etchback 反回蚀negative film 负片negative rake angle 负抠耙角network 回路;网络neutralization 中和nick 缺口nickel 镍nodule 铜瘤;瘤粒no flow resin 不流树脂noise 噪声nominal 标示nominal dimension 标定长度nominal gel time 标示胶性时间nominal resin content 标示胶含量nominal resin flow 标示胶流量nominal scaled flow thickness 标示比例流量厚度OA equip 办公室自动:化设备obsolescence factor 报废因素OEM 原设备制造商offset-list 补偿数据清单ohmmeter 欧姆计open 断路open circuits 断路open short testing 断短路测试opening 开口original art work (A/W) 原稿底片Others 其它outgrowth 增出over design 牛刀杀鸡overlap 钻尖重叠overlay entry 盖板overpotential 过电压oxidation 氧化oxide treatment 黑化处理oxided cytochrome 氧化性之细包色素oxygen evolution 氧气发生反应packed bed 充填床式pad 锡垫;圆配pad copper exposure pad露铜panel 小型板面;母板panel plating 一次铜电镀parasitic 寄生的part no. 料号pattern plating 二次铜电镀PCB ( print circuit board ) 印刷电路板pcs 片peel strength 抗撕强度peeling off 剥离(剥落) performance specification 性能规范permittivity 透电率perspectives on experience 经验透视PET 聚酯photodiode detector 发光二极管侦测器photo initiator 感光启始剂photoresist 光阻phototool 光具(指工作底片)piece 子板面pinceton applied research 腐蚀测定仪pink ring 粉红圈pit 凹点pitch 脚距planar 平面plating 电镀plating exposure 下镀层露出plug gauge 插规plug hole 孔塞PNL (panel) 排板polar-polar interaction 极性之间的吸力polyester 聚酯类polyglycols 聚乙二醇polyimide 聚亚醯氨poor bevelling 磨边加工引起突起,剥离poor drill 孔形不良poor HAL 喷锡不良poor marking 字体不良poor pad 锡垫不良poor printed 印刷偏差poor solderability 焊锡性不良poor touch-up 补线不良position control system 位置控制系统positive rake angle 正抠耙角power curve model 幕次曲线模式practice 工艺惯例preferred 良好premature tearing 提前撕裂prepolymer 预聚合物prepreg 胶片pre-process ( front-end) 制前press 压床press cycle 压合周期primary current distribution 一次电流分布primary 主要product lifetimes 生命周期product process 制程promoter 促进剂protocal 初步资料prussic acid 普鲁士酸PTF-based process 厚膜糊法PTH (plating though hole) 导通孔pull away 拉开pumice 浮石粉pumice scrub 喷砂清洁法pyrometallurgy 火烧法冶炼QC ( quality control) 品管QFP (quad flat pack ) 扁方型封装体qualification inspection 资格审查检验qualification testing 资格检定quality classification 品质等级quantitative 计量式测试rack 挂架radiometer 能量剂rake angle 抠耙角RAM [Random Access Memory 随机存取内存real time 关键时刻recessed trace process 凹槽线路法recovery tank 回收槽reduction 还原re-eninforcement 强化refraction 折光率reinforcement style 补强材料的型式register mark 对位用标记registration hole 对位孔registration pattern 长方形铜地REJ ( reject ) 退货;拒收rejectable 拒收release agent 脱模剂relief angle 浮离角remark 备注repair 修理resin content 树脂含量(胶含量)resin flow 胶流量resin flow percentage 树脂流量之百分率resin recession 树脂下陷resin smear 胶渣resist strippers 剥干膜剂resistor network 排列电阻resolution 解像度return on assets 资产报酬率reversibility 可逆性rework 重工rosin 天然松香rotating cylinder 旋转圆柱形roughtness 孔壁粗糙;粗慥routing 切外形,成型routing bit 铣刀runout 偏转S/L on hole 孔内沾文字S/M ( solder mask ), S/L 防焊文字S/M (solder mask) 防焊S/M error 防焊种类错误S/M on hole 孔内绿漆salt spray test 盐水喷雾试验sampling size 抽样数scope 范围scored 刻痕scoring 枢槽;刮线scrap 废框scratches 刮伤screen printing 网版印刷scum 透明残膜sealing 封孔处理secondary 次要semi-additive 半加成法sensitize 敏化sensitizer 敏化液separator 钢隔板sequential lamination 渐成式压法serrated edges 毛边shatter 破碎short 短路shunt 分路silane treatment 硅烷处理silicone coupling agent 硅烷偶合剂silk screen 文字印刷simulator 仿真器single axis 单轴sizing 底片之伸缩补偿skip 漏印skip printing 跳印;漏印sliver 丝条slot 开槽slotting 开槽SMD ( surface mount device ) 表面黏着组件smear 胶渣SMT ( surface mount technology )表面黏着技术sodium carbonate monohydrate 结晶水碳酸钠soft tooling 软性工具solder 焊锡; 锡铅solder bridge 锡桥solder bump 锡突solder float 漂锡solder mask adhesion 绿漆附着力solder on G/F 金手指沾锡solder on trace 线路沾锡solder plug 锡塞solder side 焊锡面solderability 焊锡性solid carbide 实质碳化物spacing 间距spacing nonenough 间距不足SPC ( Statistical Process Control ) 统计生管specification 规范special considerations 特别考虑spin coating 旋转涂布spindle 钻轴spiral contractometer 螺旋收缩仪spot face 铣靶spray coating 喷涂Squeegee 刮刀stacking structure 叠板结构stamping 冲压standard hydraulic lamination标准液压法standardizing 标准化starvation 缺胶step tablet 格片数stock option 认股选择权strain 应度strength 强度stressmeter 应力计subtractive 减除法surface convex 表面突起surface examination 表面检查surface insulation resistance (SIR) 表面绝缘电阻surface mount 表面黏着方式surface roughness 表面粗慥度surges 突波switch circuit 开关线路tab 金手指tack free 不黏taped hole gauge 锥形孔规target hole 靶孔task force 任务编组tensile strength 抗拉强度tensile stress 张性应力tent 浮盖terms and definitions 术语与定义termination load 抗匹配负载test circuit 测试线路test method 试验方法test point 测试点thermal shock 热震荡试验thermal stress 热应力试验thermistor 热电感应式thermo cycling 热循环试验theoretical cycle time 理论性周期时间thickness 厚度time to market 上市时机thickness distribution 厚度分布thief 补助阴极thin core 薄基板;内层板throwing power 分布力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之负载total quality program 全面的品质计划toughness 坚度trace error 线路错误trace nick & pin hole 线路缺口及针孔trace peeling 线路剥离trace pin-hole 线路针孔trace surface roughness 线路表面粗糙tarnish and oxide resist 抗污抗氧化剂transmittance 透光度trim line 裁切线true levelling 真平整true position 真正位置的孔;真位twist 板翘type 种类umbra 本影undercut 侧蚀uneven coating 喷锡厚镀不平整universal 万用型universal tensile tester 万用拉力试验机universal tester 泛用型测试机upper carrier 顶部承载钢uptime 稼动:时间vacuum deposition 真空蒸镀法vacuum hydraulic lamination真空液压法vaporizer 气化室V-cut V形槽vertical microsection 垂直微切片via hole 导通孔visible inventory 有形的库存vision inspection 目视检查V oid 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 随身听warehouse 仓库warp 板弯warp , warpage 板弯water absorption 吸水性wear resistance 耐磨度weave exposure 纤纹显露weave texture 织纹隐现wedge angle 契尖角week 周wet chemistry 湿式化学制程wet film 湿膜wet lamination 湿膜压膜法wet process 湿制程wetting 沾锡wetting balance 沾锡平衡法wicking 渗铜;渗入;灯蕊效应width 宽度width reduce 线细width-to-thickness ratio 宽度与厚度的比值window 操作范围work-in-process 在制品work order 工单working film 工作片working master 工作母片year 年yellow 金黄色yield 良率。

PCB专业用语一、综合词汇1、 E印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、E印制元件：printed component7、E印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayerprited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、I刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、E印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material28、覆铜箔层压板：copper-clad laminate (ccl)29、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、力口成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板： phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates(epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板： epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板:bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料I、a 阶树脂：a-stage resin2、b 阶树脂：b-stage resin3、c 阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resinII、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e 玻璃纤维：e-glass fibre43、d 玻璃纤维：d-glass fibre44、s 玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷： ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔(剖面)轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdfdatabse28、设计数据库：design database29、设计原点：design origin30、优化(设计)：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走(布)线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction （track）2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、 v 形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孑L环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孑L位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、E印制板组装图：printed board assembly drawing52、参考基准：datum referance。

1影響電性及外觀Affect upon electrical performance or appearance 2過度的Excessively3異常Abnormal4規格不符specification is below standard5品質異常quality is below standard6嚴格按照QC規定Strictly according to QC regulation7定期研磨To make regularly re-sharpen8設備device(另義:主動零件) \ machine \ equipment9參數設置錯誤parameters setting error10依保養計劃According to the maintaining plan11壓力過小lack of pressure12曝光不全\過度exposure-energy insufficient\excessive13間距不足spacing nonenough14線細width reduce15光強度Light Intensity16缺口nick\chipping17氣泡Bubble\blister\air inclusion18異物foreign particle \ foreign material（壓合異物）\dust(灰塵) 19被污染contaminated20干膜附著力不足 Poor adhesion of dry film21固定點開路fixed position open22固定點短路fixed position short23線路針孔trace pin-hole24孔破void in PTH hole\Barrel Crack25斷脖子Open near pad26靜置時間Holding time27識別方法identify method28膜屑反粘Contrary to adhere of scum29碎屑,殘材 Debris30顯影不潔Developing uncleanness31外觀不良Appearace defective32傳動\傳送速度convey speed33偏離deviation\shifted34單軸single axis35底片漲縮A/W expand or contract 36漏失率Loss Rate37補償compensation\balancing 38零件孔\面component hole\side39覆铜箔层压板\銅箔基板copper clad laminates (CCL)40線路露銅copper exposure 41織紋顯露weave exposure42光學點\基準標記fiducial mark43環氧樹脂epoxy44蝕刻速率etch rate45網布fabric46助焊劑不均勻flux coating uneven 47過濾filtration48電測治具fixture49鉆尖分離gap50標準板golden board1影響上件及外觀affect upon mounting or appearance2銅厚測量儀Copper thickness Measuring Instrument3佐證evidence4微蝕量microetching quantity5 濕度humidityinternal proofread cycle\calibration system cycle 6內部校正周期(校驗矯正)7板面刮傷Surface Scratch8制定handling 標準Define standard of handling9目視檢查\目檢visual inspection10規定頻率defined frequency11壓力計\表pressure gauge12工程程式designed program13超規格out of the tolerance14毛頭\去毛頭burr\deburring15影響下工序製作difficult to product in the following process16化學銅electroless plating17除膠速率desmearing rate18電流current19分層delamination\bulge20濕潤Damped21預浸Pre-dipped22活化液activator23速化accelerator24漂錫solder float25熱應力測試thermal stress test26孔環(焊墊)Lifted land\annular ring27熱水洗Hot water rinsing28震動馬達vibrating motor29銅渣copper residue (copper splash)\cosmetics island獨立銅渣30清潔濾網purifying filters31定期換水replace water regularly32回收槽recovery tank33加強管控to strengthen the control of sth.34酸洗\鹼洗acid\alkali rinse35定期分析濃度Analyze Conc. regularly36金屬雜質污染Contamination of metal impurities37碳化物carbide38碳處理carbon treatment39整流器(電流矯正)Current rectifier40銅厚測量儀Copper Thickness Measuring Instrument 41刷磨速度Brush Speed42速度控制器velocity controller43電流控制器current controller44吸水滾輪破舊water-absorptive roller worn-out45新水補充不足Insufficient for water replenishment46濾芯Filter element47化學藥液chemicals liquid48孔塞(孔內異物)dirty hole49多與\少與1mil厚Less\More than 1 mil Thickness 度50色差color variation1板面粘油墨屑(顯影段)sticky ink debris2擋水滾輪water apart roller3網板高度Screen height4網板張力不足Screen tension insufficient5刮刀行程Squeegee distance6刮刀刃鈍化Squeegee edge blunt7油墨黏度過大viscosity of ink too thick8張力應力tensile stress9后烤Post cure10印C面Printing Top(COMP) Side11印S面Printing (SOLD)Bottom Side12靜電噴涂Spray Coating13印可剝膠Peelable Solder Mask14風刀air knife15隔離環clearance16燒焦burning17化鎳金immersion nickel and gold18銅鎳層接著不良Poor combination the copper and nickel 19刷磨滾輪brush roller20刷幅測試brush breadth\width test21脫脂溫度Defatting Temp.22流量計flowmeter23執行\導電Conduct24助焊劑\熔合液rosin(天然松香)\flux\fusing fluids25錫粗Tin roughness26焊料中銅離子含量過高The cu2+ content out of upper in solder 27機臺異常machine-motion error28缺點標示卡nominal card of defects29程序\程式錯誤Programbug30人員疏忽operator's carelessness31日保養daily maintainance32人員技能不熟練Operator is not skilled33口頭考核examine orally34阻抗異常Impedance Abnormal35阻抗測量儀impedance measuring instrument36漏氣puncture37受潮moisture absorption38膜面污染film surface contaminated39漏檢Leaking inspection40二次元 2D(biaxial) dimension-measuring instrument 41工單run card\work order42飛針Flying Probe43目檢Visual Inspection44專用治具測試Dedicated Tester45特殊特性Critical Feature46重要特性Important Feature47銅箔厚度Copper foil Thickness48板彎翹Bow and Twist(warp)49尺寸(含對角)Size(Diagonal)\dimensions(成型)50拉力計\張力計tensile meter1棕化\黑化Brow\black oxide2循環水洗circulating water rinsing3PP膠片Prepreg4物理性質\化學性質physical\chemical character5暫存時間Temporary store time6鉚釘組合Eyelet7疊板結構stacking(lay up) structure8鉚釘rivet9熱熔機heat-melting machine10有用壽命useful life11印製電路板Printed Circuit Board(PCB)12根本原因\真因Root Cause13圍堵措施Containment Plan14現狀Current Status15原因分析Gap Analysis16內部稽核\外部稽核Internal\outside Audit17修改\變更Modify18無鹵素Halogen Free19更新\修訂Update/Revise20改進措施ure Plan21長期異常Chronic22突發異常Excursion23陶爾(壓力單位)Torr24靶孔距Space between target holes25層偏misalignment26組合線Combined producing line27鋼板\隔板steel plate\caul plate\separator28板厚測量儀Board-thickness measuring instrument 29鋼印機 steel seal machine30品質檢驗 quality examination31介質厚度dielectric thickness32吸水性moisture absorbability33耐磨性wear resistance34剝離強度stripping strength35焊錫耐熱性heat-resistant of solder36抗麻斑測試spot-resistant test37信賴性測試reliability test38介電常數測量儀dielectric constant measuring device 39包裝標籤packing tag40電子天平electrical balances41焊錫爐solder furnace42孔徑規calliper gauge43比色計color comparing meter44密度計density meter45蝕刻均勻性Etching uniformability46化驗單 laboratory list47出貨單manifest48雙面板\多層板 Reversible Board\Multi layer board 49定位孔 Location Hole50疊板數stack boards count1硝基戊烷amylnitrite2陽極泥anode slime (sludge)3液態光阻aqueous photoresist4縱橫比aspect ratio5預留在製品banked work in process 6貝他射線照射法beta backscattering7斜邊beveling8吹孔blow hole9黏結層bonding plies10焊橋solder bridge11接單生產Build To Order(BTO) 12金手指斜邊\倒角chamfering13網框chase14螯合劑chelator15化學鍵chemical bond16熱膨脹Thermal Expansion17同心圓concentric circle18密貼性conformance19消費類產品consumer products20庫倫定理coulombs law21喇叭孔countersink22試樣coupon\sample23覆蓋力covering power24挖空cut-outs25交期縮短cycle-time reduction 26專用型dedicated27縮錫dewetting28介質常數dielectric constant29孔黑\孔灰discolor hole30停機\稼動時間downtime\uptime31鉆針切削面drill facet32鉆針研磨機drill pointer33裸板(未鍍銅) blank board34延展性ductility\Elongation35留邊寬度edge spacing36金手指edge-board contact ( gold finger )\tab 37電化學反應器electrochemical reactor38脆性embrittlement39植PIN法\外部插梢法external pin method40織維突出fiber protrusion41成品final board42固著fixing43燃燒等級flammability rating44抗菌性\抗酶性fungus resistance45膠化時間gel time46一般阻焊油墨general resist ink47玻璃態轉換溫度glass transition temperature (Tg)48多孔\少孔Extra/Missing Hole49硬化劑hardener50空氣濾清器\過濾器hepa filter1規範specification\standard2銑靶spot face3衝壓\鋼印stamping4標準液壓法standard hydraulic lamination 5缺膠starvation6應力\應度strain7應力計stress meter8板面突起surface convex\swelling9板面檢查surface examination10板面粗糙度surface roughness11熱震蕩試驗thermal shock12厚度不均uneven thickness distribution 13抗污抗氧化劑tarnish and oxide resist14透光度transmittance15裁切線trim line16測試undercut17萬用型universal18有形庫存visible inventory19倉庫warehouse20濕化學制程wet chemistry process21燈芯\滲銅wicking22縱橫比width-to-thickness ratio23良率yield24點燈次數Times of Light switch25真空延遲時間Vacuum delayed time26+/-2 周The front or rear two weeks 27無塵室clean room28上噴壓Upper spray pressure29下噴壓Lower spray pressure30顯影劑developer31主軸轉速(RPM) Spindle Revolution Speed\Revolution Per MinuteRPM32光電耦合器(Charge Couple Device) CCD3390° 孔切破90 degree breakage34缺點偵測\檢測defect detection35聚焦focus36光校正calibration37極性Polarity38正極\陽極Positive39負極\陰極Negative40下鉆點\下刀點entry41量杯measuring cup42微切片Microsection43爆孔hole breakout(鑽孔)\hole overflow(防焊油墨) 44溫差temperature difference45文字不清marking(symbol) blurred46文字白點S/L white point47補充顯影additional developing48烘烤baking49確認檢修系統Visual Repair System(VRS)50圖表Diagram1腐蝕Corrosive2致癌物carcinogenic3有機體突變的Mutagenic4染色體錯位chromosome aberration5畸形teratogenic6有害氣體poisonous gas7易燃性Inflammability8爆炸性explosion9吸入\吸入劑inhalation10護目鏡goggle11棉手套Cotton glove12化學特性Chemical properties13熔點Melting point14抽樣檢查spot check15沸水boiling water16沖模Punching17氫溴化物hydrochloride18醇\酒精alcohol19持續改進continual improvement20糾正措施corrective action21環境因素\影響\方針environment aspect\impact\policy 22環境管理體系environment management system 23污染預防prevention of pollution24品質關鍵點critical to quality(CTQ)25客戶需求分析Customer Needs Mapping(CNM) 26質量功能分布Quality Function Deployment(QFD)27失效模式及後果分析Failure Mode & Effects Analysis(FMEA)28跨功能小組Cross-functional involvement 29傳感器sensor30點陣圖tally chart31全面品質管理Total Quality Management(TQM)如QC七大手法32柏拉圖Pareto Chart33因果圖\魚骨圖Cause and Effect diagrams34腦力激蕩Brainstorming35散布圖Scatter diagrams36全面設備保養Total Productive Maintenance(TPM)37控製圖Conttrol Chart38測定系統分析Gage Repeatability&Reproducibility(GRR)39印製電路板協會Institute of printed circuit(IPC)40有機保焊膜Organic Solderability Preservative(OSP)41進刀Feed42金鹽Potassium Gold Cyanide(金氰化鉀PGC)43輻射式紅外線焊Radiation(輻射) Infrared Rays(IR) Reflow(焊接)接44錫膏熔焊Reflow Soldering45縮錫Dewetting46錫爐浮渣Dross47錫尖Solder Icicle48錫球Solder Ball49電容器capacitor50波峰焊Wave Soldering1石油petroleum2線圈\纏繞coil3代理商agency4自由基Free Radical5鍍金Golden Plating6防焊阻劑Polymer coating(solder resistent) 7內層(外層)孔環Internal(external) Annular ring 8隧道式烤箱transmission toaster9直立式烤箱vertical toaster10光面\霧面油墨glossy\matte ink11晶片直接組裝Chip On Board(COB)12組裝密度packaging density13球狀陣列Ball Grid Array(BGA)14焊膏solder paste\solder cream15焊料粉末(焊粉)solder powder16觸變性thixotropy(粘度變化特性)17儲存壽命shelf life18網版(脫網)高度snap off distance19拉絲stringing20平移偏差shifting deviation21貼裝幾Placement equipment22虛焊點(焊點不佳)colder solder connection23焊盤起翹lifted land24錫珠solder ball25波峰焊wave soldering26迴流焊reflow soldering27離子清潔度ion cleaning28印製電路元件printed circuit assembly(PCA) 29特采Accept on Deviation\Use As It 30首件检验报告First Piece Inspection Report31工序变更通知Process Chang Notice（PCN）32孔銅厚度Barrel Copper thickness\Hole Copper Thickness 33面銅厚度Surface Copper Thickness34皺折wrinkle35置信區間Confidence interval36相關性Correlation37相關矩陣Correlation Matrix38任意抽樣法Haphazard Sampling39不合格品Nonconforming units40不合格Nonconformity41正態分布Normal Distribution42排列圖(柏拉圖)Pareto Chart43預測區間Prediction IntervalProbability Based Chart44基於概率的控制圖45制程能力Process Capability46二次函數Quadratic47隨機抽樣Random sampling48極差Range49合理子組Rational Subgroup50回歸控製圖Regression control chart1故障failure\breakdown2夾頭grip holder3解析度\解像度resolution4可靠度reliability5孔位錯誤(孔偏)mis hole location6孔徑\鉆孔直徑錯誤Hole Diameter error7離子污染度試驗ionic contamination testing8線距line space9線寬line width\trace width10感光油墨liquid photoimageable solder resist ink 11批batch\lotcrazing\mealing(白點)\Haloing(白邊) 12 裂痕\白斑\白點\白邊13對位不准misregistration14釘頭nail heading15數位鉆孔機NC drill16原稿底片original art work (A/W)17鉆針重疊overlap18氧化oxidation19剝離\抗撕強度peel strength20感光起始劑photo initiator21凹陷dent22塞孔plug hole\stuffing23補線不良poor touch-up24循環周期Periodically cycle25初始資料protocal26噴砂pumice scrub27對位孔registration hole28文字印刷silk screen printing\printing of legend 29膠渣resin smear30孔壁粗糙度roughtness31防焊文字S/L32毛邊serrated edges 33跳印skip printing34漂錫solder float35噴涂spray coating36刮刀Squeegee37孔規taped hole gauge 38薄基板\內層板thin core39工作片工作母片working gerberworking master gerber40粗化abrade41電流密度Current Density42風刀Air Knife43獲取資格的Qualify/qualified + n. or + to44現場locality(PD)45濃度偏低Conc. Lower46濃度偏高Conc. Higher47人員疏忽Operator careless48經緯向錯誤longitude and latitude contrary49上件不良failed componmt mounting50防呆孔Poka-Yoke hole\ mistake proofing hole1假性露銅unreal copper exposure2積墨ink accumulation3印偏ink printing deviated4遵照現場作業規範comply with the handling standardization 5放置時間Holding time6烘乾溫度不足Insufficient in dry temperature7設備故障breakdown of machine8壓膜滾輪 D/F laminated roller9sth. 受損或污染Damaged or contaminated10粘塵壓力sticky pressure11曝光燈管exposure fluorescent tube12光階 light step condition13曝偏Exposure misregistration14層間對準度alignment registration15吸氣不良vacuum treatment abnormal16曝光藏點Exposure shelter17人員動作不當improper handling18顯影Developing19蝕刻Etching20去膜stripping21Mylar 未撕Mylar non tearing off22教育訓練instruction and trainning23進行顯破點測試conduct developing point broken test 24噴壓Spraying pressure25蝕刻不潔Etching incompletely\underetch26蝕刻液Etchants27首件確認First article confirm28電性不良Electrical performance defective29去膜不凈Film stripping uncleanness30幾臺漏測Equipment test leaking31領班Foreman32主管Chief33穩定性Stability34誤判Misjudgement35混料Mixture36鋁粉濃度(火山灰)Aluminum percentage37超音波測試(錫箔Tin foil perforating test 紙)38水破測試water broken test39油墨黏度ink viscosity40黏度計viscosimeter41數孔機hole counter42振動馬達vibration motor43網版調偏net screen misregistration 44試印膜trial printing film45機臺未清潔worktable uncleaness46萬用塞孔墊板universal plugging back-up 47預烤Precure48上錫\焊錫性不良poor solderability49溫度均勻性Temp. uniformability 5010倍放大鏡10X magnifier1捲尺measuring tape2千分尺micrometer3剝離強度Peeling strength4尺寸安定性Dimensional stability5有害物質Hazardous substance6元素分析儀 element analyzing instrument7顯微鏡microscope8遊標卡尺vernier caliper9膜厚測量儀membrane thickness measuring intrument 10銑刀milling cutter\routing bit11鉆針drill bit12化學元素chemical elements13化學藥水chemical liquid14裁切刀具cutting tool15控制面板control panel16日點檢表daily check list17光面油墨glossy green ink\resist(阻焊劑防染劑) 18公差\誤差 tolerance\variance\bias(偏差)19量產mass production20白色文字white ident21成型外型routed outline22連片尺寸PNL drawing dimension23折斷邊break-away tabs24檢查表inspection sheet25記錄表data sheet\record chart26報表report forms27點檢表Check list28磨邊機Grind- edging machine\ Edger29打磨機polisher30板面光滑Board surface smooth31滴定法分析Titration analysis32溫度計Temp. meter\Thermograph33壓力計Pressure meter34能量格測試Energy-step tablet test35黏紙viscosity paper36六點測溫儀Six points Temp. uniformability test Instrument 37催化劑catalyst38穩定劑\安定劑stabilizer39硫酸銅回收機CuSO4 retrieve equipment40秒錶stopwatch41預熱preheat42計時器chronograph\timepiece43能量計energy meter44靶孔機target hole equipment45銅含量The contents of Cu46液體比重計hydrometer47比重測定法stereometry48殺菌劑sterilant49蝕刻因子Etching factor\value\element50自動光學檢測Automatical optical inspection(AOI)1精度Precision2棧板pallet3電動拖車\叉車electric trailer\fork lifter4針盤bit holder5放置架placement rack6靜止消泡時間static\rest defoaming time7轉板Transfer plate8水性筆Mark pen9尼龍\不織布\陶瓷nylon\non-woven fabric\ceramic10比色計chromo meter11濕度卡Humidity Indicator Cards12測溫儀Thermoscope13龍門吊gantry crane14搖擺\擺動swing15PIN孔重合pin hole superposing16首躺first cycle17中和洗neutralization cleaning18流量flow amount19除膠速率desmear rate20濕潤(電鍍)moisten21獲准供應商supplier warrant22供應商批准程序書Supplier Part Approval Process(SPAP) 23V-cut殘厚Remain thickness of V-cut24冷媒油refrigerant oil25壓力腳pressure foot26塊規block gauge27高度規vernier height gage28金剛砂carborundum\Emery29火山灰volcanic ash30高阻計high resistance meter31模具圖mold draw32支架Chassis33治具fixture34超音波浸洗ultrasonic dip35酸浸acid dipping36電流強度current amperage37化驗分析表Assay analysis report forms 38加壓水洗Pressurized water rinsing39酸洗acid rinsing40溢流水洗cascade water rinsing\overflow 41沉淀缸sediment tank42沖污水waste water rinsing43水柱式沖洗Jet cleaning44高壓水柱式沖洗High pressure rotating jet rinse 45清水洗Fresh water rinsing46干板組合Drying module47抗腐蝕測試accelerated corrosion test48速化反應acceleration49實際在製品active work in process50總量amount1高性能(電子)工業high performance industrial級2高延展性銅箔high temperature elongation copper(HTEC)3高溫樹脂high temperature epoxy (HTE)4孔數hole number5哈氏槽hull cell6水解hydrolysis7改善方案implementation8努普(硬度單位)Knoop(Hardness)9牛皮紙kraft paper10壓膜機laminator11刃角磨損lay back12牽引\定位螺絲lead screw13平整劑levelling additive14線性可變差動轉換器linear variable differential transformer(LVDL) 15 刷磨清潔法machine scrub16鉆頭刃帶margin17主圖\機構圖master drawing18基材利用率material use factor19濕度與絕緣電阻測試moisture and insulation resistance test20鋸齒\蝕刻缺口mouse bite21負片negative film22結瘤\銅瘤nodule23流膠量百分比resin flow percentage24膠含量resin content25報廢因素obsolescence factor26一銅panel plating27二銅pattern plating28透電率\介電常熟permittivity29極性吸引力polar-polar interaction30聚酯類polyester31孔變形poor drill32預聚合物prepolymer33原始資料protocal34噴砂清潔法pumice scrub35掛架rack36折光率refraction37對位元用標記register mark(對位點)38孔內沾文字S/L on hole39孔內防焊S/M on hole40干膜屑\透明殘膜scum41漏印\跳印skip printing42表面附著元件SMD ( surface mount device )43表面附著技術SMT ( surface mount technology ) 44錫突solder bump45漂錫solder float46油墨附著力solder mask adhesion47金手指上錫solder on G/F48線路沾錫solder on trace49錫塞solder plug50統計制程管控SPC ( Statistical Process Control )1自檢Self-examine2檸檬酸濃度Citric acid conc.3液位Liquid Level4析出物educt5垂直的perpendicular6噴砂能力pumice capability7閥門 Valve8外包加工contract-production 9退貨拒收REJ ( reject )10植PIN深度Depth of external pin 11上PIN beat PIN12精確度Precision13準確度accuracy14操作員技術不嫻熟operator technique unskilled15套环深度depth of sleeve-ring16精修(成型)finely couting17漏鉆\漏撈Leaking drilling\routing 18多鉆\多撈surplus drilling\routing 19排屑chip load20排屑槽flute21蜂鳴器check beeper22建立檔案資料(建檔)Archive data building 23合格qualified24電子稱Electronic scale25封口時間sealing time26超出範圍out of scope27微蝕速率Micro-etching ratio28變色\褪色discolor29破損breakage30電導率conductance ratio31履歷表biographic sketch32公式formula33擴孔針reaming drill bit34電木板bakelite board35允收水準general criteria36理想狀況Target Condition37模板\模具Template38基準孔reference holes39壓敏開關Piezo-switch40指示燈indicator41直方圖Histogram42并聯導體parallel conductors43導體連接處area of adjacent conductors44金屬導體Metal conductors45防焊側露(焊墊\線路)Adjacent isolated lands or conductors exposed 46有害物質公約Restriction of Hazardous Substances(RoHS) 47預防措施Precaution48生物可降解Biodegradability49生態環境ecologyDisposal50(垃圾\廢棄物)處理1浸焊Immersion Soldering2焊接點Solder Joint3焊錫絲Solder Wire4待工溫度Idle Temp.\+Time(空轉時間)5靜電釋放Electrostatic Discharge(ESD)6靜電壓力Electrostatic Overstress(ESO)7電阻係數Electrical Resistivity8內應力Internal Stress9導熱係數Thermal Conductivity10磷含量Phosphorous11顆粒大小Grain Size(μm)12X光測量X-ray Diffraction13抗拉強度Tensil Strength(N/mm2)14介面化合物Intermstallic Compound(IMC)15賈凡尼效應Galvanic Effect(不同金屬電位差加速腐蝕) 16高頻信號High Frequency Signal17肌膚效應Skin Effect(高頻線路沿道題表面傳輸)18阻隔效應Barrier Effect(合金層可有效減低離子遷移度) 19銀Silver20硫酸sulfuric acid21儀器Apparatus(測試用儀器)22拋光Polish23磨切片grind microsection24文件保存期限Documentation of age25內部管理政策Internal Policies26工資支付Salary payments27責任書Responsibility28法定最小年齡The legal minimum age29熟練\技能Facility30隱私權right to privacy31貪污\腐敗corruption32有效日期valid period33溫度循環實驗Temperature Cycling Test(TCT)34熱衝擊實驗Thermal Shock Test(TST)35離子遷移試驗Electrochemical Migration Test(ECM) 36絕緣電阻試驗Surface Insulation Resistance(SIR)37陽極燈絲Conductive Anode Filament(CAF)38爆板popcorn39生產車間Fabricating Plant40吊車crane41危隩物品hazardous substance42文字脫落symbol fading43鋸齒Worm-Eaten-Crack44經緯方向Grain Direction45V-cut Slit46幻燈片slide47預算budget48運輸工具transport49貨物cargo50容器vessel1殘差控製圖Residuals Control Chart2雙邊Bilateral3單邊(極致)unilateral4分布寬度Spread5標準差Standard Deviation6統計推斷Statistical Inference7變差Variation8區域分析Zone Analysis9可接受質量水平Accpet Quality Level(AQL)10物質安全品質表Material Safey Data Sheet(MSDS) 11錫渣Tin residue12外包商Subcontractor13結論conclusion14能力competence15工作關鍵表Job Element Sheets(JET)16目數mesh count171819202122232425262728293031 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50。