3M Scotchcast双组分环氧阻燃型电缆修复灌封胶Scotchcast 2131 TDS

4[ 30 ]GASKETINGadhesives & sealants guide [ volume 5 ]LOCTITE ® GASKET SEALANT 1 –HARD SETTING Reliable, paste-like gasket sealant/dressing/coating. Dries quickly to a hard set. Recommended for rigid, permanent assemblies. Temperature range: -65°F to 400°F (-54°C to 204°C); resists common shop fluids and fuels.Typical Applications: Anti-freeze plugs, threaded connections, manifold gaskets.Item Container Size Pack 37541 1.5 oz. tube 12375423 oz. tube12LOCTITE ® GASKET SEALANT 2 –NON-HARDENING Reliable, paste-like gasket sealant/dressing/coating. Sets more slowly to a pliable film. Best suited for non-rigid, vibrating assemblies. Allows for easy disassembly if required. Temperature range: -65°F to 400°F (-54°C to 204°C); resists common shop fluids and fuels. Typical Applications: Valve cover gaskets, oil pan gaskets.Item Container Size Pack 37543 1.5 oz. tube 12375443 oz. tube12LOCTITE ® COPPER GASKET ADHESIVE – HI-TEMP ADHESIVE SEALANTFast-drying, metallic copper sealant helps dissipate heat, prevents gasket burnout and improves heat transfer.Seals instantly. Fills hot spots and surface imperfections. Temperature range: -50°F to 500°F (-46°C to 260°C); resists all types of automotive fluids, especially gasoline.Typical Applications: Cylinder head gaskets, carburetor gaskets, exhaust manifold gaskets and other high temperature applications.Item Container Size Pack 375839 oz. aerosol can12LOCTITE ® AVIATION GASKET SEALANT – GASKET DRESSINGSlow-drying, non-hardening brushtop sealant approved for use in aviation as well as automotive applications. Temperature range: -65°F to 400°F (-54°C to 204°C); resists gasoline, oil and grease.Typical Applications: Close-fitting machined surfaces, sealing hoses, solid gaskets.Item Container Size Pack 37559 4 oz. brushtop can 123755816 oz. brushtop can12LOCTITE ® HI-TACK GASKET SEALANT – GASKET DRESSINGFast-drying sealant dries to a highly tacky, non-brittle film that holds gaskets in place during assembly. Temperature range: -65°F to 500°F (-54°C to 260°C); resists gasoline, oil, antifreeze, axle lube.Typical Applications: Valve covers, fuel pumps, carburetors, manifold gaskets.Item Container Size Pack 37554 4 oz. brushtop can 1237555 9 oz. aerosol can 123755316 oz. brushtop can12PERFORMANCE GASKET TYPEGasketing Selector ChartsProperties Chart: Gasketing* Uncured liquid adhesives may cause stress cracking of certain thermoplastics (e.g., polycarbons, acrylic and polysulfone).4[ 32 ] GASKETINGat 200 mphthere are no second choices.M&M‘S, M and the M&M‘S Characters are trademarks of Mars, Incorporated and its affiliates. © Mars, Inc. 2007. Manufactured and distributed underlicense by Henkel Corporation. Robert Yates Racing is used under license. Loctite is a registered trademark of Henkel Corporation, U.S.A. © Copyright 2007. Henkel Corporation. All rights reserved.At speeds exceeding 190 mph, we can’t afford to have anyleaks or loose fasteners on our cars. To survive the brutal stress and vibration that each race throws at us, we depend on Loctite® gasketing products to keep us on track.”– Robert Yates“THERE IS NO SECOND CHOICE.。

002623M™ Scotchcast™ Electrical Resin 262 One-Part, Class B, General PurposeEpoxy Powder ResinProduct Description3M™ Scotchcast™ Electrical Resin 262 is a widely used, well-known general purpose epoxy powder resin. A one-part, red pigmented, rapid heat-curing product, it is designed to provide a continuous, tough moisture and chemical resistant dielectric coating to a variety of substrates.• Fast curing• Excellent electrical properties• Excellent thermal shock and impact resistance• Excellent heat, chemical and moisture resistance• Good cut-through resistance• Excellent flow Scotchcast Electrical resin 262 is manufactured by a fusion blend process, insuring that each individual particle of powder contains all the components necessary to effect a complete cure and attain stated performance properties.Scotchcast electrical resin 262 is applied to an object that has been heated to a temperature above the melting point of the resin. On contact with the preheated application surface, the resin melts, flows to a controlled extent, then cures, bonding to the substrate and coalescing into a smooth, continuous, essentially uniform, thick coating. It effectively coats flat surfaces and corners, as well as, high points. Uses for Scotchcast 262 include moisture proofing and insulating armatures, stators, buss bars and toroid cores.Scotchcast™ Electrical Resin 262 – Typical PropertiesColor RedSpecific Gravity1 (cured) 1.34Dielectric Strength3 12 to 15 mil coating1000 v/milThermal Shock2 10 cycles-75°C to 155°C12 -15 mil coating 1/8’’ sandblasted steel PassesImpact Resistance212-15 mil coating 1/8’’ sandblasted steel panel Gardner 5/8’’ RadiusImpact Tester100 inch-lbsCut-Through Resistance2 – 1lb wt: 1/8 AWG wire130°C (266° F)Edge Coverage2 12-15 mil coating on flat38-48%Gel time2 @ 193°C hot plate12-16 seconds*Not recommended for specification purposes. Product specifications will be provided upon request.Test Methods1 ASTM D-7922 3M Test Method3 ASTM D-14933Corrosion Protection Products Division6801 River Place Blvd. Austin, TX 78726-9000 /corrosion Please recycle. Printed in USA.© 3M 2010. All rights reserved. 80-6111-0945-7 Rev AHandling and Safety PrecautionsRead all Health Hazard, Precautionary and First Aid,Material Safety Data Sheet, and/or product label prior to handling or use.Ordering Information/Customer ServiceFor ordering technical or product information, or a copy of the Material Safety Data Sheet, call:Phone: 800/722-6721 or 512/984-9393Fax: 877/601-1305 or 512/984-6296Important NoticeAll statements, technical information, and recommendations related to 3M’s prod-ucts are based on information believed to be reliable, but the accuracy or com-pleteness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.Warranty; Limited Remedy; Limited Liability. Because conditions of product use are outside of our control and vary widely, the following is made in lieu of all express or implied warranties: this product will conform to 3M’s published product specifications and be free from defects in material and manufacture on the date of your purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective upon your receipt, your exclusive remedy shall be, at 3M’s option, to replace the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.Usage InformationMethod of ApplicationThe rapid cure of 3M™ Scotchcast™ Electrical Resin 262 permits the use of highspeed production methods. The powder can be readily applied by spraying techniques as well as through the use of fluid bed dipping of preheated parts. Automated and manual types of application equipment are both available. Equipment manufacturers’ names can be suggested upon request.CuringThe cure of Scotchcast 262 to a thermoset condition involves a time-temperature relationship. The retained heat in application units having high heat capacity is sufficient in many casesto effect a cure of the resin without the need for post-curing facilities. For example, if an application surface can retain a temperature of 204° C (400° F) for 60 seconds after coating, it will be fully cured. Small articles, or those with a large surface-to-mass ratio, lose heat rapidly and may require a higher preheat temperature and/or additional oven- curing.The figures below represent nominal guidelines for obtaining the resin’s adhesion, impact and chemical resistance characteristics.149° C (300° F)40 minutes177° C (350° F)20 minutes204° C (400° F)60 seconds232° C (450° F)30 secondsThe user must determine the time required for the coated substrate to reach listed temperatures.Preheat Temperature RangePrior to applying Scotchcast electrical resin 262, the part must be preheated to a temperature ranging from 150° C (302° F) to 260° C (500° F). The optimum preheat temperature depends upon the size, heat capacity and configuration of the object to be coated, as well as the method of application. The ideal coating temperature will vary for each application and is best determined by experimentation.StorageLaboratory evaluation indicates that the usable shelf life of the product is twenty four (24) months from the date of manufacture when stored at temperatures not exceeding 27° C (80° F), providing the material is stored in its original container. Care should be taken when removing the resin from the original container to prevent inclusion of foreign material. After the resin removal, the bag should be retied immediately. This will help to avoid agglomeration caused by excess moisture. For best results, store in a cool, dry place.00262。

3M胶⽔规格说明书TDS3M ? Scotch-Weld ? Structural AdhesivesLoad-bearing formulations for metals,rubber, glass and more.As an alternative to mechanical or fusion fastening, the reasons for Scotch-Weld Adhesives are many: greater design latitude, cleaner lines, material sub-stitution, less machining, lighter weight, more dura-bility, and often less cost.To meet application and end-use requirements you can select from one-part heat-curing epoxies, and two-part room-temperature curing epoxies, acrylics and urethanes. There are formulations for bonding steel, aluminum, copper, low surface energy plas-tics, rubber, glass, wood, masonry and more.Whatever properties you need–durable adhesion, flexibility, creep resistance, heat and environmental resistance, void-filling —you’ll likely find a Scotch-Weld product to meet your requirements and expectations.3M has long been recognized as a pioneer in struc -tural strength adhesives. But to meet end use perfor -mance requirements doesn’t just mean providing the right chemical formula. Which is why 3M also develops dispensing systems to facilitate production in low and high volume assembly. Many two-part 3M formulations are available in Duo-Pak cartridges for dispensing with a manual or pneumatic 3M ?EPX ? Applicator.Aircraft entry steps – Brush-applied 2-part Bicycle frame assembly – 3M ? Sco tch-Weld ? Bonding magnets to steel rotor –Bonds 3M ? Sco tch-Weld ? Adhesive 2216 B/A provides a Epoxy Adhesive DP-420 bonds steel couplings made with 2-part 3M ? Sco tch-Weld ? Epoxytough, flexible bond between honeycomb and the into aluminum tubing of the frame. Couplings are Adhesive DP-460 cure at room temperature and framework in entry step panels of commuter air-threaded for easy assembly and disassembly. The reach 4500 psi in overlap shear strength. Void-fill-craft.toughened epoxy bonds for the long run in ing properties secure loose fitting surfaces.high stress areas.Ellsworth Adhesives 1-800-888-0698Product Information: 3M? Scotch-Weld?Adhesives in Duo-Pak CartridgesWe are on the web@ /doc/d89c2de49b89680203d8250d.html Product Information: 3M ?Scotch-Weld ?Two-Part StructuralProduct Information: 3M ? Scotch-Weld ?Adhesives in Duo-Pak Cartridges (cont.) Average Overlap Mix Approximate Approximate T-Peel PSI Ratio Viscosity Worklife At 75°F Product(Volume) 75°F (24°C) At 75°F (24°C) -67°F 75°F 180°F 250°F (Color)FeaturesB:A (CPS) (24°C) PIW (-55°C) (24°C) (82°C) (121°C)DP-8005 ? Structurally bonds polyolefins without 10:127,5002.5-3 Min.16–2000340– Off-White, surface preparation ? Excellent Black environmental resistance ? 2-3 hourhandling strengthD u o -P a k C a r t r i d g e sSizes 35ml 250mlGal Pail DrumAverage Overlap Shear StrengthMix Approximate Approximate T-Peel PSI Ratio Viscosity WorklifeAt 75°FProduct (Volume) 75°F (24°C) At 75°F (24°C) -67°F 75°F180°F 250°F(Color) FeaturesB:A (CPS) (24°C) PIW (-55°C) (24°C) (82°C) (121°C) 1751 B/A ? Long worklife adhesive ? Rigid epoxy 3:2700,00045 Min.414002000500300Gray8-12 hrs. handling strengthExcellent void filler and machinable for many "Body Solder" applications 1838 B/ALong worklife adhesive Rigid epoxy 4:5 400,000 60 Min. 4 1500 3000 500 300Green8-12 hrs. handling strength Meets MIL-A-23941AExcellent Environmental Resistance 1838 B/A Long worklife adhesive Rigid epoxy 6:5 250,000 60 Min. 5 1500 3000 500 300Tanof B/A 1838 Green Adhesive1838-L B/A ? Long worklife adhesive ? Rigid epoxy 1:1 10,000 60 Min. 5 2000 3000 400 200Translucent ? 8-12 hrs. handling strengthTranslucent, low viscosity version of 1838 B/A Green Adhesive 2158 B/A Long worklife adhesive Rigid epoxy 1:1 375,000 120 Min. 4 1700 2000 400 300Gray ? 8-12 hrs. handling strength ? General purpose product2216 B/A ? Long worklife adhesive? Flexible epoxy 2:3 80,000 90 Min. 25 2000 2500 400 200Gray8-12 hrs. handling strengthCan bond plastic, metal and other dissimilar materials2216 B/A ? Long worklife adhesive? Flexible epoxy 2:3 350,000 90 Min. 252000 2500 400 200Tan ? 8-12 hrs. handling strengthNon sag2216 B/A ? Long worklife adhesive? Flexible epoxy 1:1 10,000 120 Min. 25 3000 2000 200 100Translucent ? 16-20 hrs. handling strengthTranslucent versionof 2216 B/A Gray Adhesive 3501 B/A ? Fast cure adhesive ? Rigid epoxy 1:1 500,000 7 Min. 5 1500 2400 300 200 Gray20-30 minutes handling strengththat can bond metal, wood, most plastics and masonry products 3532 B/A ? Fast cure adhesive1:1 30,000 7 Min. 25 2500 2000 300 150Brown20-30 min. handling strength Semi-rigid urethaneRapid cure for flexible bonds of many plastics, wood, and rubber 3535 B/A Very fast cure adhesive1:1 30,000 3 Min. 25 2500 2000 300 150Off-White15-20 min. handling strength Semi-rigid urethane Faster setting version of 3532 B/A Adhesive 3549 B/A Long worklife adhesive 1:1 30,000 60 Min. 25 2500 2000 300 150Brown2-4 hrs. handling strength Semi-rigid urethane Longer worklife version of 3532 B/A AdhesiveT w o -P a r t U r e t h a n e A d h e s i v e sT w o -P a r t E p o x y A d h e s i v e sSizes 2oz, Pt Qt, Gal Pail 2oz, Pt, Qt Gal, PailQt, Pail2oz, Pt, Qt Gal, Pail2oz, Pt, Qt Gal, Pail Pail2oz, Pt, Qt Gal, Pail Pail2oz, Pt, Qt Gal, Pail2oz, Pt Gal2oz, Pt Pail2oz, Pt2oz, Pt PailS h ear Strengt h8-12 hrs. handling strength Tan version Tan version of 2216 B/A Gray Adhesive Rapid room temperature curing material Ellsworth Adhesives 1-800-888-0698 Product Information: 3M? Scotch-Weld? One-Part Epoxy Adhesives; Metal PrimersWe are on the web@ /doc/d89c2de49b89680203d8250d.html3M? Scotch-Weld? Electronic Grade Epoxy AdhesivesHigh-performance specifically for demanding electronics applications.For assembly of sophisticated electronics where outgassing and corrosion of adhesive bonds are a concern, Scotch-Weld Electronic Grade (EG) epoxies are the advanced alternative to mechanical fasteners and lower-grade adhesives. These 2-part epoxies produce far lower contamination levels of ionic and outgassing impurities than typical epoxy adhesives. Chloride content is lower than standard industrial counterparts.Targeted dispensing is easy with the3M? EPX? Applicator System. Duo-Pak cartridges with long shelf life are stored at room temperature for added convenience in many oper-ations.17Component rigidization –3M? Scotch-Weld? Voice coil assembly – Controlled flow ofEpoxy Adhesive DP-125EG reaches handling 3M? Scotch-Weld? Epoxy Adhesive DP-460EG strength within 3 hours at room temperature. provides a clear, targeted application in bonding Stabilizes board components with 1500 psi the coil into the head gimble assembly.shear strength and 20 piw.Ellsworth Adhesives 1-800-888-06983M? Scotch-Weld? Film AdhesivesFilm adhesives for the best combination of fatigue resistance and highest performance.Film adhesives can be formulated with the highest performance level of all structural strength adhesives available. Scotch-WeldFilm Adhesives offer the best combinationof shear and peel strength, plus shock and fatigue resistance. They also provideseveral other advantages:Uniform adhesive thicknessthroughout joints for an even, securebond line.Adhesive confined to immediatebonding area for a clean operationand less waste.Simple application for fast assembly.Stability for extended usability andshelf life.Precise fit – Available in various thicknesses Simultaneously seal and bond – In metal-and widths, 3M? Scotch-Weld? Film Adhesive to-metal lamination 3M? Scotch-Weld? Film can be die-cut into shapes to facilitate bonding of Adhesives bond with up to 4800 psi shear complex parts. strength and provide a barrier against water,fuels, and oil.We are on the web@ /doc/d89c2de49b89680203d8250d.html3M? Pronto? Instant AdhesivesFast bonding with the rightcombination of strength, curetime and viscosity.For speed and performance, you’ll likely find a product in this line with precisely the right combination of bond strength, cure time and viscosity.These one-part cyanoacrylate adhesives rapidly reach handling strength at room tem-perature without a catalyst. On many applica-tions, bonds reach handling strength in 5–10seconds and 80% of full strength in an hour.A single drop per square inch can bond manyplastics, rubber, metal and more with tensilestrength up to 5000 PSI.Depending on the specific formulation, youhave the following features: resistance tofuels, lubricating oils and other chemicals from-40°F to 200°F (-40°C to 93°C); gap filling;extended cure rates for repositionability; highpeel and impact strength; conformance toMIL-Spec A-46050C.With 3M? Pronto? Instant Adhesives appli-cation is easy from their own containers orthrough intermediate manual dispensers or auto-mated systems. Curing requires no expensiveequipment or fixturing.A single drop of 3M? Pronto? Instant To bond a flexible PVC mat into a high 3M? Pronto? Instant Adhesive CA-8 is an Adhesive quickly bonds many plastics, rubber, impact polystyrene turntable, 3M? Pronto? Instant excellent multi-purpose product for use in a variety metal and more. Adhesive CA-40H provides high viscosity and a of assembly applications. slower set time to meet handling requirements.Architectural pottery – For repair of fiber-3M? Pronto? Instant Adhesive CA-40 works Veneer and wood repair – 3M? Pronto? glass/ concrete cast pottery, 3M? Pronto? Instant on many problem surfaces where other adhesives Instant Adhesive CA-40H is a high viscosity Adhesive CA-50 Gel bonds with high tensile and may fail, such as bonding EPDM rubber. liquid for void filing between veneer and core. A shear strength. Non-sagging formulation applies light spray of 3M? Pronto? Surface Activator over neatly when bonding curved surfaces. the adhesive before assembly accelerates curingspeed.Product Information: 3M? Pronto? Instant AdhesivesEllsworth Adhesives“Your One- Stop Shop”Adhesive & chemical products from allthe top manufacturersDispensing equipment-manual to fully automaticComplete tech support (inside and out) An outside sales staff that is very willing to serve (most are degreed engineers) Custom packaging to your specification We are easy to reach:in person-check the location nearestyou on the phone -1-800-888-0698over the internet @/doc/d89c2de49b89680203d8250d.html Have an application problem? CallEllsworth Adhesives at 1-800-888-0698We are on the web@ /doc/d89c2de49b89680203d8250d.html3M? Jet-Weld? Thermoset Adhesive SystemHot melt speed and structuralstrength performance in thepalm of your hand.This single system combines many production benefits typical of hot melt adhesives and bond performance usually associated with 2-part structural adhesives.Fast initial set can help you reduce costs. Fast handling strength helps eliminate or minimize fixturing and speed assembly.One-component, moisture-curingformulation eliminates metering, mixing and curing equipment. And 100% solids give you a low-VOC adhe-sive system with no drying equipment and no attack on plastics.With the long bonding range and initial repositionability, assembly of complex parts is easier. Bond lines are thin, flexible and tough for improved part fit, appearance and rugged performance.Combine this versatility with the applicator's portability, and you have a system that can adapt readily to many of your production requirements.The 3M? Jet-Weld? II Applicator and moisture-curing urethane adhesives put a powerful production capability in your assembly operation. Bond strength approaches the high end of the performance range, exceeding many con-ventional hot melts and PVA (polyvinyl acetate) adhesives. Bond wood, plastics, rubber, dissimilar materials, plasti-cized vinyls, and more.Decorator tables – 3M?Jet-Weld?Adhesive Trade show booths –3M?Jet-Weld?Adhesive Speaker assemblies – Flexible, tough bond performs multiple tasks including V-groove bonds extruded aluminum bracket to laminate lines of 3M?Jet-Weld? Adhesive holdbonding at the table joints. covering of honeycomb panel. Bracket is for dissimilar materials and multiple components. hanging graphics.High performance gliding windows – With Bent wood furniture – With 100% solids 3M? Wood furniture – 3M? Jet-Weld? Adhesive is fast handling strength, 3M?Jet-Weld?Adhesive Jet-Weld?Adhesive, a manufacturer holds the aes-easily applied as a bead for bonding wood helps speed the bonding of interior wood trim thetic contours of unique bentwood furniture. furniture and cabinet components. Fastto the vinyl sash. handling strength helps speed production. Ellsworth Adhesives 1-800-888-0698Product Information: 3M? Jet-Weld?Adhesives1 234Job-matched tips –1) Threaded cap for sealing tip after use.2) Extension tip for improved sight linein hard-to-reach areas.3) .062" tip for low flow applications.4) .125" tip for high flow applications. .090" tip standard on 3M?Jet-Weld?II Applicator. Container sizes to meet your production volume – ? 10 fl.oz. cartridges 2k foil packsGallon pail5 gallon pail55 gallon drumWe are on the web@ /doc/d89c2de49b89680203d8250d.html3M Light Cure AdhesivesSelect UV curing versions for thin films and coatings, and bonding heat-sensitive substrates. For curing through thicker sections, visible light formulations cure to depths of 2" to almost 4".For visible light, the 3M Curing Light VL1 (at right) is a compact and convenient hand tool for spot curing.Wire tacking – To reduce processing time, Potting – All 3M ?Light Cure Adhesives feature 3M ? Light Cure Adhesives cure on demand superior depth of cure for potting applications.with exposure to UV or visible light.Precision bonding, potting, encap-sulation, tacking, andmore at the speed of light.With cure speeds generally less than 5 seconds, you can raise the speed limit for many electronics assem-bly applications. These specialized acrylate formula-tions cure on demand when exposed to UV or visible light. And for precision targeting and placement, each adhesive in the line is available in 3, 5, 10, and 30ml EFD ?-compatible syringes.Use with manual, semi-automatic, or fully automatic dispensing systems to meet your production require-ments for encapsulation, potting, fixturing, wire tacking, sealing, conformal coating, and lens bonding.Ellsworth Adhesives 1-800-888-06983M ? Fastbond ? and Scotch-Grip ? Contact AdhesivesA tradition of 40 years and the performance you’ll want for a long time to come.This line offers a wide range of choices for con-tact adhesive applications. Select from bonding ranges, strengths, solids content, and solvent or water-based formulations to meet requirements for bonding laminate, foam, and more. In the line, you’ll find the water-basedpioneer 3M ? Fastbond ? Contact Adhesive 30 NF – proven for almost 40 years in cabinet shops and still in compliance with current and current-ly proposed air quality regulations. Plus, there’s the latest innovation – 3M ? Fastbond ? Contact Adhesive 2000-NF with handling speed exceed-ing most solvent-based systems and up to 350 psi in overlap shear.The Fastbond Water-Based StoryWhile competition pressures you to improve productivity, regulatorylegislation demands that you move toward more environmentally-responsible tech-nologies. Some local and regional regula -tions have made traditional solvent-based contact adhesives virtually obsolete. Fastbond is the 3M trademark on a contin-ually growing line of water-based adhesives that are helping many industries meet the challenge right now and aim for the fore-seeable future. By replacing solvent-based adhesives, compliance is getting easier in Tabletop lamination – With 3M ? Fastbond ?Foam fabrication –In compound cushion more and more applications.Contact Adhesive 2000-NF, you get three times the cov-assembly, high tack 3M ? Fastbond ? Foam erage of a typical solvent-based system. For produc-Adhesive 100 holds curves in seconds. Lighter tion speed, you go from spray to trim in seconds.density foam is adhered around the higher density core with a smooth rounded edge.Buy only the quantity you need – Depending on the specific 3M ? Fastbond ? Adhesive, you can select quart or gallon jugsfor convenient handling, or 5-gallon pails and 55-gallon drums for largebulk dispensing.Upholstered household furniture – 3M ? Fastbond ? Foam Adhesive 100 quickly bonds substrates throughout chairs and couches. Bond foam to foam and fiber fill, foam to wood, fiber fill to fabric, and more. Cabinet assembly – 3M ? Fastbond ? Contact Adhesive 30-NF is a formulation proven in shops for four decades. Combines open time of up to 4 hours with high immediate bond strength. Apply with roller, brush, or spray gun.Marine carpeting – In bonding carpet to fiberglass flooring and steps, 3M ? Fastbond ?Contact Adhesive 2000-NF helps withstand the foot traffic and moisture in boat cabins.Product Information: 3M ? Fastbond ? Contact Adhesives, Water-BasedProduct Information: 3M ? Scotch-Grip ? Contact Adhesives************************************/minuteseparationrate.*********************************/minuteseparationrate.Note: 3M ? Hi-Strength 90 Adhesive, a Note: Flash Point (closed cup) in all Fastbond Adhesives: None. popular 3M aerosol adhesive, is now also available in bulk form.We are on the web@/doc/d89c2de49b89680203d8250d.html3M ? Fastbond ? and Scotch-Grip ?AdhesivesInnovative answers toa wide variety of non-struc-tural bonding challenges.3M ? Scotch-Grip ? Adhesives are industrial tools designed to provide innovative answers to a wide variety of non-structural bonding problems.Some formulations are tailored to specific types of applications such as Scotch-Grip Plastic Adhesives. These high strength, fast drying elastomers bond polycarbonate, vinyl, and many other plastics to themselves and materials such as wood or metal. With Scotch-Grip Rubber and Gasket Adhesives you can easily bond neoprene, EPDM, and many more.Other Scotch-Grip Adhesives are multi-purpose and used worldwide in hundreds of different product assembly operations. If you’re looking for a reliable non-structural adhesive, you’re likely to find just what you need in the Scotch-Grip Adhesives line backed with more than 50 years of 3M adhesives research and engineering.Containers to meet your production requirements – Depending on the specific 3M ? Scotch-Grip ? Adhesive, you can select drums, cans, pails, or handy tubes.These collapsible tubes are self-containedlightweight applicators to give you “take-it-to-the-job” convenience for multi-station or low volume assembly and field repairs.Pinball machine refurbishing – 3M ? Scotch-Grip ? Plastic Adhesive 4693H bonds and seals decorative translucent plastic inserts into the underside of the playing surface. Up to 60 minutebonding range with contact bond properties.Light fixture assembly – To prevent moisture Chemical drum gasket – With excellent penetration, a pressure flow gun applies 3M ?resistance to fuel and oil, 3M ? Scotch-Grip ?Scotch-Grip ? Rubber and Gasket Adhesive to bond a Rubber and Gasket Adhesive 847 bonds and seals rubber gasket into a commercial light fixture cover.drum gaskets in place. Very low VOC formulation.Display board – 3M ? Scotch-Grip ? Plastic Adhesive 1099 bonds wood flooring samples to a plastic display board with overlap shear strength ofmore than 385 psi. Very low VOC formulation.Washing machine repair – 3M ? Scotch-Grip ? Rubber and Gasket Adhesive 1300 bonds with high immediate strength and seals the doughnut ring seal in the outer tub. Bond line resists up to 300°F (149°C).Sporting goods – In bonding plastic feathers and nocks onto arrow shafts, fast-tacking 3M ?Scotch-Grip ? Plastic Adhesive 4475 dries quickly to a firm bond. Resists plasticizers, water, and heat up 200°F (93°C). Product Information: 3M? Scotch-Grip? Plastic AdhesivesEllsworth Adhesives 1-800-888-0698Product Information: 3M Insulation and Light DutyAdhesivesHVAC duct insulation – Easy and economicalto apply, 3M? Fastbond? Insulation Adhesive 49 is asingle-component water-based pressure sensitiveformulation with instant tack to speed assembly. We are on the web@ /doc/d89c2de49b89680203d8250d.htmlNote: 3M? Super 77? Adhesive, a popular aerosol adhesive, is now available in bulk form for high vol-ume applications on many light-weight materials.3M Sealant TechnologiesSolutions for the elements from windows to ductwork.Air, water, dirt, fuel, cold, heat – keeping these or other elements in or out is a challenge in applications as varied as windows and doors, truck lap seams, HVAC ductwork, vinyl siding, and livestock troughs. With 3M ? Scotch-Seal ? and Weatherban ? Sealants, you have a wide selection of solutions based on more than 50 years of development and innovation. Meeting your volume requirements – Depending on the formulation, 3M sealants are To meet your requirements, you’ll find formulations available in caulking cartridges, collapsible from acrylic to polyurethane, and forms from self-applicator tubes, pails, drums, or rolls. liquids to tapes.Ductwork – 3M ? Scotch-Seal ? Duct Sealer 900 fills gaps and cures quickly to a firm rubbery seal on medium and high pressure ductwork for heat-ing, ventilating, and air conditioning.Product Information: 3M ? Scotch-Seal ? and Weatherban ? SealantsProduct Information: 3M Aerosol AdhesivesProduct Information: 3M ? Hi-Strength 90 and Super 77?Adhesives in Bulk3M’s most popular aerosol adhesives are now available in bulk form. The following char-acteristics of interest to higher volume users supplement the chart above.We are on the web@/doc/d89c2de49b89680203d8250d.html 3M ? Shipping-Mate ? Aerosols for PackagingThe convenient system to help your package do its full job.A package performs three functions –containment, protection, and communication. The Shipping-Mate aerosol family can help you save time and effort for the full job. For containment in shipping and handling, rely on Shipping- Mate case sealing adhesive for neat, clean bonds with carton- tearing strength. For protection, you have fewer worries with Shipping-Mate palletizingadhesive stabilizing coated cartons or bags. For communica -tions, Shipping-Mate labeling adhesive bonds to even difficult sur- faces, and Shipping-Mate Box Re-nu covers unwanted printing to provide a new looking surface.3M aerosol chemicals contain no methylene chloride, chlorofluo -rocarbons (CFCs), or 1,1,1-trichlorethane (methyl chloroform).3M ? Shipping-Mate ? Case Sealing Adhesive3M ? Shipping-Mate ? Labeling Adhesive – 3M ? Shipping-Mate ? Box Re-nu Coating – – Helps save time and money if you fill miscellaneous Clear spray adhesive permanently bonds labels to To save the cost of new corrugated cartons, this orders, have cartons that come unglued, fill by hand, many problem surfaces such as glass, rubber, or easy- to-use aerosol covers most printing and or open and close for inspection. Quick drying to metal where other adhesives or gummed labels labels with permanent tan color for carton reuse. keep pace with your operation. may fail. Moisture-resistant formulation. Quick drying and long lasting.N/R = Not recommended AdhD T.M. C-700: 1/8" birch veneer bonded to 1/8" birch AdhD T.M. C-483; 500 g load for 1 hr. at noted temp. N/A = Not applicableveneer.All container sizes 24-fl. oz. except Box Re-nu AdhD T.M. C-449. Coating.Ellsworth Adhesives 1-800-888-0698。

低热膨胀系数环氧胶
低热膨胀系数环氧胶粘剂是一种特殊类型的胶粘剂，具有较低的热膨胀系数。

这使得它在粘接不同材料时能够保持更好的尺寸稳定性，特别是在复杂温度环境下。

低热膨胀系数环氧胶粘剂通常用于精密部件的粘接，如光学仪器部件、传感器、特种电机灌封、微波天线反射盘等。

这种类型的胶粘剂在制造过程中通常需要特殊的配方和技术，以实现较低的热膨胀系数。

它们通常由环氧树脂、固化剂、填料和其他添加剂组成。

通过选择合适的配方和填料，可以降低胶粘剂的热膨胀系数。

此外，低热膨胀系数环氧胶粘剂还需要在粘接过程中采取一些特殊措施。

例如，在粘接之前对被粘材料进行预处理，如表面清洁和粗糙化，以提高粘接效果。

在粘接过程中，还需要控制温度和压力，以确保胶粘剂能够充分填充被粘材料之间的间隙，并实现良好的粘接。

总的来说，低热膨胀系数环氧胶粘剂是一种重要的工程材料，在许多领域都有广泛的应用。

它们能够提供可靠的粘接效果，并保持被粘材料在复杂温度环境下的尺寸稳定性。

Battery Bonding GuidePushing beyond limitsis what bonds us.3M™ Scotch-Weld™ Structural Adhesives are what bond thousands of diverse and demanding applications in hundreds of industries, spanning more than 60 years. From aerospace to automotive, from electronics and appliances, manufacturing industries of transformative innovation have been fueled in part with the assured reliability of 3M™ Scotch-Weld™ Structural Adhesives.As a global provider and innovator of adhesive and tape bondingsolutions, 3M remains uniquely positioned to help solve evolvingdesign challenges. Our 3M Global Adhesive Solution Labs allowus to help our customers with development, modeling, testingand technology for bonding solutions, and dispensingapplications for manufacturability.Advancing next-generation power supplies.As technologies converge, requiring greater capacity, connectivity, transportability and sustainability, the demands for high-density portable power have never been greater. 3M understands the challenges facing customers, including reducing battery weight, enhancing reliability and life, managing thermal requirements, ensuring safety, and facilitating manufacturability. With decades of experience and a leading array of solutions, 3M is equipped to help deliver on your innovation.Elevate your design with proven bonding solutions.3M solutions for battery bonding offer:• Product formulations ranging from low-viscosity adhesives, non-sag options, gap fillers, sealants,thin bond tapes and 3M™ VHB™ Tapes.• High-performance characteristics such as faster cure times including no-heat cure cycles, reducedor zero surface preparation, low odor and non-flammable bonding. • Application engineering, automation knowledge and testing capabilities, design lab resources tocreate better products, plus global supply chain availability to keep production flowing smoothly.From next-generation electrochemical cells for increasingly powerful mobile products to large-scale, high-voltage battery systems for Electric and Hybrid Electric Vehicles, few application areas are as demanding for adhesives as battery bonding. 3M™ Scotch-Weld™ Structural Adhesives offer advanced solutions for bonding dissimilar materials, and our expertise helps you apply them.3M TMVHB TM T ape3MTMScotch-Weld TM Structural Adhesives3M TM High Performance Label Materials3M TM Sealants3M TMScotch-Weld TM Structural Adhesives3M TMVHB TM T ape3M TM Thin Bond T apesThermally Conductive Gap FillerA p p l i c a t i o nP r o d u c t s3M™ Scotch-Weld™ Structural Adhesives Urethane: DP6310NS/DP6330NSFlexible epoxy: DP1253M™ Scotch-Weld™ Structural Adhesives Flexible epoxy: DP1253M™ Scotch-Weld™ Structural AdhesivesT oughened epoxy: DP420/DP4603M™ Scotch-Weld™ Structural Adhesives Urethane: DP6310NS/DP6330NSKey Markets/Industries (Industrial/Electronics/Portable)-General Industrial global battery/charger manufacturing-Transportation: automotive, commercial vehicles, specialty vehicles (i.e. agricultural, forklifts, etc.)-Telecommunications -Energy Storage Systems -Lawn, Garden & T ools-Electronics: laptops, mobile, tablets Type of applicationsAcross battery pack and module designs for a variety of configurations, applications andoperating conditions, 3M™ Scotch-Weld™ Structural Adhesives meet the most demanding bonding, filling and sealing requirements.3M offers specialized understanding and experience for bonding of cells in cylindrical, prismatic and pouch configurations, and we meet requirements specific to your unique application and substrates to ensure reliable operation, durability and bond integrity.Key markets and applications.-Tension rod & pressure or end plate bonding-Battery box bonding (from reinforcement bars to entire box)-Crash box bonding-Lid to battery box sealing -Cell to frame bonding -Battery tray bondingPrismatic Cell BondingCylindrical Cell BondingBattery assembly to housingBattery assembly to cooling plateBattery cell ormodule to side plate-Bonding & encapsulating cells -Potting cells-Cell to cell bonding-Bonding of thermal runaway materials -Cell to cooling plate bondingApplicationPossible 3M Solutions Features & BenefitsBattery AssemblyCell to cell (prismatic)DP6310NS/DP6330NS• High strength bonds • E xcellent water, humidity and chemical resistance• Room temperature or accelerated heat cure • E xcellent elongation & stress strain properties • Non-sag option• Bulk options for automated dispenseModule to module DP125• H igh strength bonds under expansion, contraction and limited movement • F lexible bond for vibration and shock resistance • E xcellent water, humidity and chemical resistance• Bulk options for automated dispenseBattery Box AssemblySide plate and cover attachmentDP6310NS/DP6330NS• High strength bonds • E xcellent water, humidity and chemical resistance• Room temperature or accelerated heat cure • Excellent elongation & stress strain properties • Non-sag option• Bulk options for automated dispense DP8010/DP8010NS• Limited surface prep• Low surface energy bonding • R esists many chemicals, water, humidity and corrosion• Non-sag option• Bulk options for automated dispenseTS230• Fast set time • H igh strength bonds that are plasticizer resistant • Bulk options for automated dispenseBattery cover trim assembly TS230• Fast set time • H igh strength bonds that are plasticizer resistant • Bulk options for automated dispense DP8010/DP8010NS• Limited surface prep• Low surface energy bonding • R esists many chemicals, water, humidity and corrosion• Non-sag option• Bulk options for automated dispenseStiffener and tension rod bonding DP125• H igh strength bonds under expansion, contraction and limited movement • F lexible bond for vibration and shock resistance • E xcellent water, humidity and chemical resistance • B ulk options for automated dispensePerformance characteristics you can count on.3M structural adhesive products offer industry-leading selection and the largest levels of consistent, reliable performance to satisfy a host of essential characteristics in battery bonding applications.Application Possible 3M Solutions Features & BenefitsStiffener and tension rod bonding DP420/DP420NS/DP420LH•E xcellent environmental, vibration and shockresistance•H igh peel & shear strength for lasting bond in highand low temp•R oom temperature or accelerated heat cure•N on-sag & low halogen options•B ulk options for automated dispenseDP8407NS•L imited surface preparation•S trong bonds with broad temperature range•F ast cure time•B ulk options for automated dispenseCell to Frame BondingPrismatic cells DP420/DP420NS/DP420LH•E xcellent environmental, vibration and shockresistance•H igh peel & shear strength for lasting bond in highand low temp•R oom temperature or accelerated heat cure•N on-sag & low halogen options•B ulk options for automated dispenseDP125•H igh strength bonds under expansion, contractionand limited movement•F lexible bond for vibration and shock resistance•E xcellent water, humidity and chemical resistance•B ulk options for automated dispense Cylindrical cells DP125•H igh strength bonds under expansion, contractionand limited movement•F lexible bond for vibration and shock resistance•E xcellent water, humidity and chemical resistance•B ulk options for automated dispenseThermal Management SystemsBattery tray bonding DP420/DP420NS/DP420LH•E xcellent environmental, vibration and shockresistance•H igh peel & shear strength for lasting bond in highand low temp• Room temperature or accelerated heat cure• Non-sag & low halogen options• Bulk options for automated dispenseDP8407NS•L imited surface preparation•S trong bonds with broad temperature range•F ast cure time•B ulk options for automated dispenseDP8010/DP8010NS• Limited surface prep• Low surface energy bonding•R esists many chemicals, water, humidity andcorrosion• Non-sag option• Bulk options for automated dispenseBattery Bonding Product SelectionProduct Name Product #Color Approx.Viscosity at 75° F Approx.MixedWork Lifeat 75°CSize UPC Stock #3M™ Scotch-Weld™ Multi-Material Composite Urethane DP6310NS Green Non-sag paste9 mins48.5 mL400 mL5 gal - Part A5 gal - Part B50 gal - Part A50 gal - Part B00-076308-86407-100-076308-86398-200-076308-86782-900-076308-86748-500-076308-86783-600-076308-86749-27100109829710010983071001439607100143915701041531670104121993M™ Scotch-Weld™ Multi-Material Composite Urethane DP6330N S Green Non-sag paste30 min s48.5 mL400 mL5 gal - Part A5 gal - Part B50 gal - Part A50 gal - Part B00-076308-86431-600-076308-86433-000-076308-86780-500-076308-86701-000-076308-86781-200-076308-86727-07100109828710010982771001439617100143701701040961170103661453M™ Scotch-Weld™ T oughened Epoxy DP420Black30,00020 mins50 mL200 mL400 mL1 gal kit5 gal - Part A5 gal - Part B55 gal - Part A55 gal - Part B00-638060-08966-800-021200-41530-200-021200-41529-600-051115-25796-400-021200-41532-600-021200-41531-900-021200-41534-000-021200-41533-3710014873171000079567100077148700004638170000008347000000827701036596770103097503M™ Scotch-Weld™ T oughened Epoxy DP420NS Black180,00020 mins50 mL200 mL400 mL5 gal - Part A5 gal - Part B55 gal - Part A55 gal - Part B00-638060-08987-300-021200-39286-300-021200-39287-000-021200-31309-700-021200-56587-800-048011-58133-000-048011-58132-371001487587100036943710001068070000008577000000853710016035271001603343M™ Scotch-Weld™ T oughened Epoxy DP420Off-White30,00020 mins50 mL200 mL400 mL5 gal - Part A5 gal - Part B00-638060-08978-100-021200-87832-900-021200-87833-600-021200-82239-100-021200-82238-4710014873671000771367100002516710000114471000011453M™ Scotch-Weld™ T oughened Epoxy DP420LH Off-White30,00020 mins200 mL400 mL00-051111-07697-200-051111-07696-5701032955071000753363M™ Scotch-Weld™ Flexible Epoxy DP125Gray52,50025 mins48.5 mL200 mL400 mL5 gal - Part A5 gal - Part B00-638060-08985-900-032300-87844-200-021200-87845-900-021200-87218-100-021200-87217-4710014873570001212647100076727710008458871000845383M™ Scotch-Weld™ Flexible Epoxy Clear DP125Trans-lucent15,00025 mins48.5 mL200 mL400 mL00-638060-08983-500-021200-87842-800-021200-87843-57100148734710002541970001212623M™ Scotch-Weld™ Acrylic Adhesive DP8407Gray20,0007 mins45 mL490 mL1 gal - Part A1 gal - Part B55 gal - Part A55 gal - Part B00-638060-14631-600-638060-14643-900-638060-14658-300-076308-86306-700-638061-14659-000-076308-98878-47100179482710017948071001792647100105384710017944271001049873M™ Scotch-Weld™ Acrylic Adhesive DP8410NS Green70,00010 mins45 mL490 mL1 gal - Part A5 gal - Part A5 gal - Part B55 gal - Part B00-051115-70994-400-051115-70995-100-051115-68981-900-051115-70997-500-051115-68980-200-051115-71101-5710002405571000240457100102180710008453271001015067100084535Continued on next pageIndustrial Adhesives & Tapes Division3M CenterBuilding 225-3S-06St. Paul, MN 55144-10001-800-362-3550/structuraladhesives3M and Scotch-Weld are trademarks of 3M Company. Please recycle. Printed in USA.© 2020 3M. All rights reserved.Product Selection and Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.Warranty, Limited Remedy, and Disclaimer: Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXP RESS OR IMP LIED, INCLUDING, BUT NOT LIMITED TO, ANY IMP LIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A P ARTICULAR P URP OSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of Liability: Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.The 3M legacy in structural adhesives is built upon listening and problem-solving. Our bonding solutions can help provide greater design freedom, reduce parts and weight, enhance performance while reducing labor and material costs.3M supports our customers with the testing, technology, and training needed to create better products. Our worldwide support staff has the experience you can rely on for everything from structural adhesive selection and process improvement to help with automation and dispensing.These are just a few of the ways we connect our technology to your ideas. Science is what bonds us. Let us show you how 3M can help make your products better.Science. The 3M Difference.Battery Bonding Product Selection, cont.April 2020。

3M#Scotch-Weld结构胶粘剂3M长期以来一直被公认为结构型强力胶粘剂领域里的先导厂商。

为了满足应用和最终使用的需求，您可以选择单组份热固环氧树脂、双组份室温固化环氧树脂、丙烯酸和聚氨酯。

有多种配方可应用于粘接钢、铝、铜低表面能级的塑料、玻璃、木材、砖石及其他一些材料。

环氧树脂胶:3MDP105,DP110透明/灰色，DP100,DP100NS,DP100FR,DP125,DP190透明/灰色,DP270透明/黑色,,DP420黑/灰白,DP460,DP460EG，DP460NS,DP810,DP810NS,DP818,DP80053MDP818灰色特性：对许多种金属塑料和许多其他材料具有优良的粘接性能，室温快速固化，较好韧性，可粘接轻微油污的金属表面，不必表面处理。

混合比（容积）B：A：1：1粘度近似值（2）750F（240C）（CPS）：600750F（240C）时的操作时间近似值（3）：15-20分钟750F（240C）时的T型剥离（4）（PIW）：22重叠剪切强度（5）（PSI）：1．-670F（-550C）：31002．750F（240C）：31503．1800F（820C）：19004．2500F（1210C）：1450（6）规格：50ml/支包装：12支/箱3MDP420灰白色特性：中等操作时间的坚韧型环氧树脂，1~2小时达到操作强度，高性能混合比（容积）B：A：2：1粘度近似值（2）75℉（24℃）（CPS））：4500075℉（24℃）时的操作时间近似值（3）：20分钟75℉（24℃）时的T型剥离（4）（PIW）：503MDP460灰白色特性：长操作时间的坚韧型环氧树脂，2~4小时达到操作强度，满分足MIL-A-23941A标准。

混合比（容积）B：A：2：1粘度近似值（2）75℉（24℃）（CPS）：4500075℉（24℃）时的操作时间近似值（3）：60分钟75℉（24℃）时的T型剥离（4）（PIW）：603MDP100为快速固化胶水，共有4种，DP100透明，DP100PLUS透明（超透明），DP100NS半透明流动性弱型，DP100FR满足UL94V-0自熄型胶水！快速固化粘胶剂，硬质环氧树脂15-20分钟达到操作强度可机械施工产品混合比（容积）B：A：1：1粘度近似值（2）75℉（24℃）（CPS）：1300075℉（24℃）时的操作时间近似值（3）：4分钟75℉（24℃）时的T型剥离（4）（PIW）：23MDP105清澈透明特性：清澈透明,快速固化，极其柔性,优异的剥离强度，适用于金属，塑料，橡胶等的粘接。

The original, now better than ever!3M ™ Scotchbond ™ Universal Plus AdhesiveThe benchmark adhesive you trust …Added radiopacitycaries-affected dentinAdvanced bonding to dentaland restorative substrates, includingFull dual- and self-curewithout additionaldual-cure activator bottlev a t i v e-freel a t i o n…Added radiopacityRadiolucency under an existing restoration could lead tomisdiagnosis and invasive overtreatment. 3M™ Scotchbond™Universal Plus Adhesive is the first radiopaque universaladhesive with dentin-like radiopacity, helping to overcomethis issue.“These doubtful X-rays happen every day; most often critical step in bitewing radiograph, class II in proximal box.”– Prof. Dr. Angelo Putignano, University of Marche-Ancona, ItalyIntentional adhesive pooling under Class I restorations –X-rays of extracted human molars, filling material 3M™ Filtek™ One Bulk Fill Restorative. K. Dede et al., J Dent Res 99 (Spec Iss A): 192 IADR, 2020 – 3M internal data, H. Loll et al., J Dent Res 99 (Spec Iss A): No. 757, 2020“Radiolucent adhesive pooling underneath a restoration doubles the risk of restoration replacement.”– Dr. John O. Burgess, University of Alabama, USABrasilia (UnB), Brazilan Experimental Universal Adhesive with Caries-Affected Dentin, J Dent Res 99 (Spec Iss A): 191 IADR, 2020➀➁➂➃➄➅Non-RadiopaqueAdhesive3M™ Scotchbond™Universal Plus Adhesive3M, Filtek, RelyX and Scotchbond are trademarks of 3M Company or 3M Deutschland GmbH.© 3M 2020. All rights reserved.3M Oral Care2510 Conway AvenueSt. Paul, MN 55144-1000 USAPhone 1-800-634-2249/dentalFully aligned system with3M ™ RelyX ™ Universal Resin CementExcellent bond strength for virtually all dual-cure resin cement indications. Simplified workflows – adhesive cured by RelyX Universal Resin Cement.Ordering InformationVialwith smooth and even surface – easy to wipe off excessUnit Dosefor efficient hygiene management –reduces the risk of cross contaminationItem no.Product information3M ™ Scotchbond ™ Universal Plus Adhesive – Vial41293Intro Kit Vial1 Vial 5ml, 50 Disposable Brushes, 1 Etchant Syringe 3ml, 25 Dispensing Tips 41294Refill Vial – 1 x 5ml 41295Refill Vial – 3 x 5ml412633M ™ Scotchbond ™ Universal Etchant Etching Gel 2 Syringes x 3ml, 50 Dispensing Tips3M ™ Scotchbond ™ Universal Plus Adhesive – Unit Dose 41297Intro Kit Unit Dose50 Unit Doses, 1 Etchant Syringe 3ml, 25 Dispensing Tips 41298Unit Dose 100100 Unit Doses, 1 Etchant Syringe 3ml, 25 Dispensing Tips 41299Unit Dose 200200 Unit Doses, 1 Etchant Syringe 3ml, 25 Dispensing Tips 41304Unit Dose 400400 Unit Doses, 1 Etchant Syringe 3ml, 25 Dispensing TipsAdvanced bonding to glass ceramicScotchbond Universal Plus Adhesive reaches the gold standardReport conclusion:3M ™ Scotchbond ™ Universal Plus Adhesive performed better than 3M ™ Scotchbond ™ Universal Adhesive for glass ceramic(IPS e.max ® CAD, Ivoclar Vivadent) bonding. After the glass ceramic was etched with HF acid, a favorable ‘immediate’ and ‘aged’ share bond strength were recorded.。

33M ™ Scotchkote ™ Epoxy Coating 323/323iApplication GuideProduct Description3M ™ Scotchkote ™ Liquid Epoxy Coating 323/323i is a two part system designed to protect steel pipe and other metal substrates from the harsh affects of corrosion.Hand Application1. Mix part A and part B separately.2. Pour part B into part A completely.3. Thoroughly mix using mix stick until color consistencyis achieved.70°F/20°C 28 minutes Recommendations• Prepare only the quantity of coating that can be appliedwithin given pot life.• A ¼ in (6 mm) nap, lint free roller is suggested.• For the speed of application, and to extend the working timeof the product, pour mixed product directly on to substrate/pipe, then pull the mixture down around pipe with brush or roller.• Because of the high viscosity of this product, we suggestmixing parts A & B together at temperatures above 60°F/15°ing a brush or roller, apply Scotchkote 323/323i to a minimum thickness of 25 mils/625 microns or as specified.As an ARO, apply Scotchkote 328 to a minimum thickness of 40 mils/1000 microns. Overlap the pipe coating no less than 1 in /25 mm. Allow coating to properly cure before handling.General Application StepsFor use as a joint coating, a refurbishing coating, or as pipe coating.1. Remove oil, grease, and loosely adhering deposits.2. Verify the air temperature is 5°F/3°C above the dew point.3. Abrasive blast clean surface to NACE #2/SSPC-SP10, ISO8501:1 SA-2 1/2 near white metal.4. With air hose, clean blasted surface of any abraded debristhen verify anchor profile is 2-4 mils/50-100 microns.5. With the substrate between 41°F/5°C and 200°F/93°C dewpoint 5°F/3°C below air temperature, apply Scotchkote™ Liquid Epoxy Coating 323/323i at minimum film of 25 mil/ 625 microns.6. Apply Scotchkote 323/323i as soon as possible afterblasting but no more than 4 hours.7. Allow to cure per time & temperature chart below.8. Visually or electrically inspect the coating for defects.9. Repair all defects using Scotchkote 323/323i as repairmaterial.Repair Process1. Remove oil, grease, and loosely adhering deposits.2. Abrade the coating surface with medium grit sandpaper (80grit). Ensure that the surrounding coating is abraded on all sides of the holiday.3. Ensure abraded surface is cleaned of any debris with airblast or clean lint free cloth.4. With the substrate between 41°F/5°C and 200°F/93°C dewpoint 5°F/3°C below air temperature, apply Scotchkote ™ Liquid Epoxy Coating 323/323i at minimum film of 25 mil/ 625 microns.Cold Weather Repair Process1. Follow steps 1–3 from “Repair Process” above.2. Using a butane torch heat the surface to be repaired.3. *CAUTION*: Do not make contact with flame to coatingor allow existing coating to brown.4. Apply 3M ™ Scotchkote ™ Liquid Epoxy Coating 323/323i tothe damaged area at minimum of 25 mils/625 microns.5. Using the butane torch, apply heat to the patch toaccelerate cure process.6. *CAUTION*: Do not make contact with flame to coatingor allow existing coating to brown.Coverage in Quart/0.95 Liter Kit per WeldPipe Diameter (inches)Total Length to Coat (inches) 68101260.060.080.100.13120.130.170.210.25200.210.280.350.42240.250.330.420.50300.310.420.520.63360.380.50.630.75420.440.590.730.88480.50.670.84 1.00— Assume no waste. Based on 25 mil thickness.— F or dimensions, please see our coverage calculator on our web site (/corrosion)3M™ Scotchkote™ Spray System HSS-450 The application of Scotchkote™ Liquid Epoxy Coating 323/323i has been simplified using 3M™ Scotchkote™ Spray System HSS-450. The HSS-450 system utilizes a dual-cartridge setup along with unique application equipment designed specifically to sprayapply Scotchkote 323/323i.For more information and additional literature on the 3M™Scotchkote™ Spray System HSS-450 system, please visit our web site at /corrosion or contact our Customer Service Center at 1-800-722-6721.450 ml Cartridge Heating ProcessThis process makes use of microwave oven to heat the 450ml cartridges. Do not open cartridge at any time during this process. Proper PPE is recommended which includes but limited to: safety glasses, coverall, and chemical resistance gloves. 1. Verify power output of microwave as higher power will heatcartridge quicker.2. Place 450 ml cartridge in microwave oven.3. You heat in 30 second intervals until you can verify howlong your microwave oven takes to heat to 120°-140°F. 4. Use a Pyrometer to verify that the outside of cartridge hasreached 120°-140°F.5. *CAUTION*: Do not allow cartridge temperature to exceed140°F as the back plunger will soften and material will leak Helpful Plural Component Spray Information• Suggested tip size of 625• Tip pressure 2,500 – 3,500 psi/18 – 22 MPa• Preheat Part A to 140°-160°F/60°-70°C• Preheat Part B to 130°-150°F/55°-65°C• Mix ratio of pumps is 2:1Equipment Clean-upMEK or toluene may be used to clean spray equipment, rollers, and brushes. Utilize proper safety guidelines when working with solvent.Product Temperature Pot Life Dry To Touch Time Back Fill Time 40°F/5°C45 minutes6-7 hours10-12 hours 60°F/16°C30 minutes3-4 hours4-6 hours 75°F/23°C22 minutes2-3 hours2-4 hours 85°F/29°C14 minutes70-90 minutes1-2 hours 100°F/38°C10 minutes40-70 minutes40-60 minutes 120°F/49°C8 minutes20-40 minutes20-40 minutes*It is very important to note that times listed above are approximation and will vary due to ambient and substrate temperature or a combination of both.3Infrastructure Protection Division6801 River Place Blvd.Austin, TX /corrosionPlease recycle. Printed in USA.© 3M 2013. All rights reserved.80-6111-8644-8Handling & Safety PrecautionsRead all Health Hazard, Precautionary, and First Aid statements found in the Material Safety Data Sheet, and/or product label prior to handling or use.Ordering Information/Customer ServiceFor ordering technical or product information, or a copy of the Material Safety Data Sheet, call:Phone: 800/722-6721Fax: 877/601-13053M and Scotchkote are trademarks of 3M Company.Important NoticeAll statements, technical information and recommendations related to 3M Products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using the 3M Product, you must evaluate it and determine if it is suitable for your intended application. Because conditions of Product use are out-side of our control and vary widely you assume all risks and liability associated with such use. Any Product-related statements not contained in current 3M publications, or any contrary statements contained in your purchase order, shall have no force or effect unless expressly agreed to in writing by an authorized officer of 3M.Warranty; Limited Remedy; Limited Liability.3M warrants that Product will conform to 3M published specifications upon shipment. If Product is proven not to have met the specifications your exclusive remedy and 3M’s sole obligation will be, at 3M’s option, to replace the Product or to refundthe purchase price of the Product. EXCEPT WHERE PROHIBITED BY LAW, THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY , FITNESS FOR A PARTICULAR PURPOSE OR THOSE ARISING FROM A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE . Buyer is an expert in its field and is responsible for determining if Products are suitable for a particular purpose or application. 3M has no obligation under this warranty with respect to any Product that has failed due to inadequate or improper storage, handling, surface preparation, application, or main-tenance; failure to follow Product instructions; or alteration or damage to the Product caused by accident, neglect, or misuse. EXCEPT WHERE PROHIBITED BY LAW, IN NO EVENT SHALL 3M BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES (INCLUDING LOST PROFITS) ARISING FROM THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ASSERTED.Multiple CoatsScotchkote ™ Liquid Epoxy Coating 323/323i has been formulated to achieve a coating thickness of 45 mils/1150 microns in one coat. If additional thickness is required, apply the additional coats within 4 hours of the initial coat at temperature of 70°F/20°C. This coating may be applied in any thickness consistent with producing an acceptable surface finish.RECOAT WINDOWAir Temperature Recoat Window60° F/15°C 4 hours 75°F/23°C 3 hours 85°F/28°C 2 hours 100°F/36°C1 hour。

Scotch-W eld TMEpoxy AdhesiveDP420 Black •DP420 NS Black •DP420 Off-White •DP420 LH2022Product Description 3M™Scotch-Weld™Epoxy Adhesives are high performance, two-part epoxyadhesives offering outstanding shear and peel adhesion, and very high levels ofdurability.Features •High shear strength•High peel strength•Outstanding environmentalperformance•Easy mixing•20 minute worklife •Controlled flow (3M™ Scotch-W eld™ Epoxy Adhesive DP420 NS Black)•Recognized as meeting UL 94 HB – Underwriters Laboratory Horizontal Burn Flammability Test (3M™ Scotch-W eld™ Epoxy Adhesive DP420 Off-White)•Low halogen content (3M™ Scotch-W eld™Epoxy Adhesive DP420 LH)Typical Uncured Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.3M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHTypical Cured Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.The properties of cured 3M™ Scotch-W eld™ Epoxy Adhesive DP420 NS Black and 3M™ Scotch-W eld™ Epoxy Adhesive DP420 LH are expected to be similar to the properties of 3M™ Scotch-W eld™ Epoxy Adhesive DP420 Black and 3M™Scotch-W eld™Epoxy Adhesive DP420 Off-White, respectively as described by data in the following sections of this technical data sheet.An exception to this is the concentration of halogens in 3M™ Scotch-Weld™ Epoxy Adhesive DP420 LH. 3M™ Scotch-Weld™ Epoxy Adhesive DP420 LH is a form of 3M™ Scotch-Weld™ Epoxy Adhesive DP420 Off-White that can be considered “lo w halogen”. Low halogen is defined by the Electrotechnical Commission (IEC) 61249-2-21 standard as having less than 900 ppm chlorine, 900 ppm bromine, and less than 1500 ppm total chlorine and bromine.3M™ Scotch-Weld™ Epoxy Adhesive DP420 LH Test ResultsPage 2 of 103M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHTypical Curing Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Rate of Strength Build-UpAluminum, Overlap Shear (7 mil Bondline) (ASTM D 1002-72)Bonds Tested at 73°F (23°C)3M™ Scotch-Weld™ Epoxy Adhesive DP420 Black1This represents the oven temperature to which the bonds were subjected for the prescribed time. The average bondline temperature during the cure time will be somewhat lower than the oven temperature.NOTE: The data in this data sheet were generated using the 3M™ EPX Applicator System equipped with an EPX static mixer, according to manufacturer’s directions. Thorough hand-mixing will afford comparable results.Page 3 of 103M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHTypical Adhesive Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Substrates and TestingA.Overlap Shear (ASTM D 1002-72)Overlap shear (OLS) strengths were measured on 1 in. wide 1/2 in. overlap specimens. These bonds were made individually using 1 in. x 4 in. pieces of substrate except for aluminum. Two panels 0.063 in. thick, 4 in. x 7 in. of 2024T-3 clad aluminum were bonded and cut into 1 in.wide samples after 24 hours. The thickness of the bondline was 0.005-0.008 in. All strengths were measured at 73°F (23°C) except where noted.The separation rate of the testing jaws was 0.1 in. per minute for metals, 2 in. per minute for plastics and 20 in. per minute for rubbers. The thickness of the substrates were: steel, 0.060 in.;other metals, 0.05-0.064 in.; rubbers, 0.125 in.; plastics, 0.125 in.B.T-peel (ASTM D 1876-61T)T-peel strengths were measured on 1 in. wide bonds at 73°F (23°C). The testing jaw separation rate was 20 inches per minute. The substrates were 0.032 in. thick.C.Bell Peel (ASTM D 3167)Bell peel strengths were measured on 1/2 in. wide bonds at the temperatures noted. The testing jaw separation rate was 6 in. per minute. The bonds are made with 0.064 in. bonded to 0.025 in.thick adherends.D.Cure CycleWith the exception of Rate of Strength Build-Up Tests, all bonds, were cured 7 days at 73°F (23°C) at 50% RH before testing or subjected to further conditioning or environmental aging.Aluminum, Overlap Shear, at Temperature (PSI)1Represents time in test chamber oven before test.Metals, Overlap Shear, Tested @ 73°F (23°C) (PSI)3M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LH NT: Not testedTypical Adhesive Performance Characteristics (continued)Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Substrates and Testing (continued)Aluminum, T-Peel (PIW), at TemperatureMetals, T-Peel, Tested @ 73°F (23°C) (PIW)Aluminum, Bell Peel (PIW), at TemperatureOther Substrates, Overlap Shear Tested @ 73°F (23°C) (PSI)1Isopropyl Alcohol Wipe. See Surface Preparation Section D for additional information.2Isopropyl Alcohol/Abrade/Isopropyl Alcohol: See Surface Preparation Section E for additional information.3Substrate failure.3M ™ Scotch-W eld ™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHTypical Adhesive Performance Characteristics (continued)Note: The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.Substrates and Testing (continued) Environmental Resistance Aluminum (Etched)Measured by Overlap Shear Tested @ 73°F (23°C) (PSI)1 (ASTM D 1002-72)1Data reported are actual values from the lots tested and may be higher than values published elsewhere in this data sheet.2 d = days3i = immersion3M ™ EPXPneumatic Applicator Delivery Rates200 ml Applicator – Maximum Pressure 58 psi*Tests were run at a temperature of 70°F ± 2°F (21°C ± 1°C) and at maximum applicator pressure.3M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHHandling/Application Information Directions for Use3M™ Scotch-Weld™ Epoxy Adhesive DP420 is supplied in dual syringe plastic duo- pak cartridges as part of the 3M™ EPX Applicator System. The duo-pak cartridges are supplied in 50 ml, 200 ml and 400 ml configurations. To use the EPX cartridge system simply insert the duo-pak cartridge into the EPX applicator. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If simultaneous mixing of Part A and Part B is desired, attach the EPX mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive.When mixing Part A and Part B manually the components must be mixed in the ratio indicated in the typical uncured properties section of this data sheet. Complete mixing of the two components is required to obtain optimum properties.Two-part mixing/proportioning/dispensing equipment is available for intermittent or production line use. These systems are ideal for line uses because of their variable shot size and flow rate characteristics and are adaptable to most applications.Apply adhesive to clean, dry surfaces, joint parts and secure until adhesive sets (see rate of strength build up).Surface Preparation The following surface preparations were used for substrates described in this TechnicalData Sheet.A.Aluminum EtchOptimized FPL Etch - 3M (test method C-2803)1.Alkaline degrease – Oakite 164 solution (9-11 oz./gallon water) at 190°F ±10°F (88°C ± 5°C) for 10-20 minutes. Rinse immediately in large quantitiesof cold running water (3M test method C-2802).2.Optimized FPL Etch Solution (1 liter):Material AmountDistilled Water 700 ml plus balance of liter (see below)Sodium Dichromate 28 to 67.3 gramsSulfuric Acid 287.9 to 310.0 gramsAluminum Chips 1.5 grams/liter of mixed solutionTo prepare 1 liter of this solution, dissolve sodium dichromate in 700 ml ofdistilled water. Add sulfuric acid and mix well. Add additional distilled waterto fill to 1 liter. Heat mixed solution to 66 to 71°C (150 to 160°F). Dissolve1.5 grams of 2024 bare aluminum chips per liter of mixed solution. Gentleagitation will help aluminum dissolve in about 24 hours.To FPL etch panels, place them in the above solution at 150 to 160°F (66 to71°C) for 12 to 15 minutes.Note: Review and follow precautionary information provided by chemicalsuppliers prior to preparation of this etch solution.3.Rinse immediately in large quantities of clear running tap water.3M™Scotch-W eld™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White • DP420 LHSurface Preparation (continued)4.Dry – air dry approximately 15 minutes followed by force dry at 140°F(60°C) maximum for 10 minutes (minimum).5.Both surface structure and chemistry play a significant role in determining thestrength and permanence of bonded structures. It is therefore advisable tobond or prime freshly primed clean surfaces as soon as possible after surfacepreparation in order to avoid contamination and/or mechanical damage.Please contact your 3M sales representative for primer recommendations.B.Oakite DegreaseOakite 164 solutions (9-11 oz./gallon of water) at 190°F ± 10°F (88°C ± 5°C) for 2 minutes. Rinse immediately in large quantities of cold running water.C.MEK/Abrade/MEKWipe surface with a methyl ethyl ketone (MEK) soaked swab, abrade and wipe with a MEK soaked swab.* Allow solvent to evaporate before applying adhesive.*Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.D.Isopropyl Alcohol Wipe Only Surface PreparationWipe surface with an isopropyl alcohol soaked swab.* Allow solvent to evaporate before applying adhesive.*Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.E.Isopropyl Alcohol/Abrade/Isopropyl Alcohol Surface PreparationWipe surface with an isopropyl alcohol soaked swab, abrade using clean fine grit abrasives, and wipe with an isopropyl alcohol soaked swab.* Then allow solvent to evaporate before applying adhesive.*Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use.3M ™ Scotch-W eld ™Epoxy AdhesiveDP420 Black • DP420 NS Black • DP420 Off-White •DP420 LHStorageStore products at 60-80°F (15-27°C) for maximum shelf life.Shelf LifeThese products have a shelf life of 24 months from date of manufacture in original containers at room temperaturePrecautionary InformationRefer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.Technical InformationThe technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information.Product Selection and Use Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the useand performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.Warranty,Limited Remedy, and DisclaimerUnless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of LiabilityExcept for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2008 standards.Industrial Adhesives and Tapes Division3M Center, Building 225-3S-06St. Paul, MN 55144-1000800-362-3550 • 877-369-2923 (Fax) /structuraladhesives 3M and Scotch-Weld are trademarks of 3M Company. ©3M 2012 78690097106Automotive Disclaimer Automotive Applications: This product is an industrial product and has not been designed or tested for use in certain automotive applications, including, but not limited to, automotive electric powertrain battery or high voltage applications. This product does not fully adhere to typical automotive design or quality system requirements, such as IATF 16949 or VDA 6.3. This product may not be manufactured in an IATF certified facility and may not meet a Ppk of 1.33 for all properties. The product may not undergo an automotive production part approval process (PPAP). Customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s automotive application and for conducting incoming inspections before use of the product. Failure to do so may result in injury, death, and/or harm to property. No written or verbal statement, report, data or recommendation by 3M related to automotive use of the product shall have any force or effect unless in an agreement signed by the Technical Director of 3M’s Automotive Division. Customer assumes all responsibility and risk if customer chooses to use this product in an automotive electric powertrain battery or high voltage application, and 3M will not be liable for any loss or damage arising from or related to the 3M product or customer’s use of the product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity or recall costs), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability. In no event shall 3M be liable for any damages in excess of the purchase price paid for the product.NOTWITHSTANDING ANY OTHER STATEMENT TO THE CONTRARY, 3M MAKES NO REPRESENTATIONS, WARRANTIES OR CONDITIONS WHATSOEVER, EXPRESS OR IMPLIED, REGARDING THE PRODUCT IF USED IN AN AUTOMOTIVE ELECTRIC POWERTRAIN BATTERY OR HIGH VOLTAGE APPLICATION, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY ON PERFORMANCE, LONGEVITY, SUITABILITY, COMPATIBILITY, OR INTEROPERABILITY, OR ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE.。

Instructions for Dispensing and Troubleshooting3M™ Scotch-Weld™ Structural AdhesivesGeneral Instructions for Use of 3M™ EPX™ ApplicatorsAlmost invariably, the cause of incomplete curing of a structural adhesive is highly off-ratio dispensing. The following steps should be practiced minimizing occurrence of this off-ratio dispensing.To ensure proper mix ratio with 3M™ Scotch-Weld™ Duo-Pak adhesives and 3M™ EPX™ applicators, the following steps are recommended:1)Store cartridges cap end up and feet end down —do not leave them lying on their sides. This will allowany air bubbles to work up to the tip of the cartridge.2)Remove and discard cap from cartridge.3)Place cartridge in applicator and begin dispensing; visually ensure that adhesive is flowing from bothsides of the cartridge. This will remove any air bubbles that may be present in the cartridge, and also equalize the pistons if they were not precisely level.4)Once material is flowing from both sides of the cartridge, attach mix nozzle.5)Dispense and discard approximately one mL of adhesive.6)Begin applying adhesive to part to be bonded.When done using adhesive, do not remove nozzle. Store material with the nozzle attached. When ready to use more adhesive, remove and discard nozzle with gelled adhesive and begin following steps above with step 3.If the exit orifice of the mix nozzle is larger than desired for dispensing, Luer lock adapters and a large variety of dispensing needle tips can be purchased from sources such as Ashby Cross or Nordson EFD.NOTE: Use of a dispensing tip can provide significant additional backpressure and, in some cases, lead to off-ratio dispensing. Validate all tips by comparing to material dispensed without a tip.Additional NotesMix nozzles are designed to work with adhesive at room temperature. Adhesive that is very cold (below60°F/15°C) may be hard to dispense. Adhesive that is very warm (above 90°F/32°C) may flow very easily. Care should be taken to visually ensure that material exiting the mix nozzle is uniform in color (no streaks).To dispense material more rapidly, mix nozzles may have the tips cut back, or adhesive may be gently warmed (to as high as 120°F/50°C) using an oven, warming pad or lamp. DO NOT place adhesive cartridges in a microwave oven.If the adhesive is difficult to dispense, remove and replace mix nozzle. DO NOT try to force gelled material through the mix nozzle, or the cartridge and/or applicator may become damaged.Instructions for Dispensing and Troubleshooting 3M™ Scotch -Weld™ Structural AdhesivesPage 2 of 2 Mix nozzles are intended for one-time use. DO NOT attempt to flush a mix nozzle with solvent and reuse it later.Do not attempt to express material with a pneumatic applicator at pressures higher than recommended (50 PSI for the 45 and 50mL dispensers; 58 PSI for 200 mL dispenser, 70 PSI for 400 and 490mL dispensers) or cartridge damage may occur.Storing the used cartridges tip up will encourage any entrapped air bubbles to float to the tip of the cartridge, where they can be expelled prior to attaching a nozzle.T echnical Information The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Suchinformation is intended for people with knowledge and technical skills sufficient to assess and applytheir own informed judgment to the information. No license under any 3M or third party intellectualproperty rights is granted or implied with this information.Product Selection and Use Many factors beyond 3M’s control Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property. Warranty, Limited Remedy, and DisclaimerUnless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liablefor any loss or damage arising from or related to the 3M product, whether direct, indirect, special,incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless ofthe legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strictliability.This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2008 standards.Industrial Adhesives and Tapes Division 3M Center, Building 225-3S-06 St. Paul, MN 55144-1000 3M and Scotch-Weld are trademarks of 3M Company. 800-362-3550 • 877-369-2923 (Fax)©3M 2014/structuraladhesives。

Project:2006-053M电力系统防火封堵3M中国有限公司2006年05月一．3M公司简介3M公司全称为明尼苏达矿业制造股份有限公司（由英文全名M innesota M ining & M anufacturing Corporation中前三个英文单词的首字母组成），多年来一直是全球500强企业之一，并名列全球“最受崇敬企业”前十位，也是美国华尔街道琼斯30种工业股票成分指数的公司。

公司创建于1902年，总部设立在美国明尼苏达州圣保罗市。

3M生产制造的产品在世界二百多个国家及地区进行销售。

一百年来，3M针对客户的需求发明了多不胜数的创新产品。

“3M创意全为您”的企业精神已成为3M公司服务客户的真实写照。

3M中国有限公司在中国由外商投资的独资企业，并在国内建有自己的工厂和技术中心，可更好地为中国的客户提供全面的技术服务。

3M防火封堵材料产品是基于其核心技术---精密陶瓷材料开发出来的创新产品，产品完全符合市场需求。

得到全球范围内广大客户的充分信赖。

3M卓越的产品质量，严格的质量控制，让全世界的客户感到放心。

今天，3M防火延烧产品已广泛应用在核电站、高层建筑、化工厂、电信大楼、变电站、发电厂、医院、半导体芯片厂、钢铁厂、军工厂、船舶工业、银行、大型公众场所等等。

全系列的防火封堵材料组成了3M的具有创新意义的完善的建筑物被动防火保护系统，这些系统有助于阻止火焰、烟雾及有毒气体的蔓延和传播。

产品被许多权威机构如UL、FM、Warnock-Hersey、Omega Point及中国国家防火材料检测中心NCFM检测认证为合格的被动防火保护系统。

事实上3M公司是世界上目前为止唯一的能够制造出如此众多的被认证的被动防火材料的公司。

本资料介绍使用的3M公司防火封堵材料已通过国家防火建筑材料质量监督检验中心检测合格。

所使用的3M公司防火封堵材料通过了美国UL：Underwriters,Inc.保险商实验所（又称美国安全检测实验室）和美国FM：Factory Mutual Researcdh 美国ＦＭ保险公司研究中心检测合格。

美国3M公司绝缘与防护产品一级授权代理商一、Scotchcast™电气绝缘涂料525BG无溶剂双组分液体聚氨酯涂料1、产品描述• 3M Scotchcast™ 525BG专门为各种金属底材的电气绝缘防护而设计，在各种严酷的腐蚀条件下为金属底材提供持续的绝缘防护。

• 3M Scotchcast™ 525BG分为基料和固化剂两个组分，具备很高的反应活性，能够实现室温固化。

从而降低能源消耗，并免去加热设备的投资。

• 3M Scotchcast™ 525BG拥有刷涂和其他灵活高效的施工方法，能够为各种结构复杂的金属提供长久的绝缘防护，能通过不同涂层厚度满足不同绝缘要求。

• 3M Scotchcast™ 525BG的应用包括母线槽、开关柜及变电站的绝缘防护等。

2、产品性能•室温固化• 100%固含量，零VOC •专为人工刷涂开发，也可用于双泵无气喷涂•高膜厚，一次成膜厚度可达0.5mm-1.0mm •与各种金属具备良好的粘结性能•耐老化性能突出•优良的柔韧性和抗机械损伤性能•优良的耐化学品和耐湿热性能3、Scotchcast™电气绝缘涂料525BG －主要特性4、3M 母排绝缘液体涂料解决方案二、521+ 电气绝缘树脂1、产品描述• 3M 521+电气绝缘树脂是加热固化的单组分环氧树脂粉末，可应用于各类被保护物体表面，使其形成连续的、坚硬的、耐潮性和耐化学溶剂性优异的绝缘涂层。

• 3M 521+环氧粉末可应用于热浸涂工艺，首先加热被涂工件到3M熔点以上温度，然后浸涂上粉。

粉末粘附到被加热工件表面后开始熔化并产生流动，然后固化并与被涂物体表面粘连形成一层光滑、连续、厚薄均匀的涂层。

该涂层能有效包裹被涂物体的平面和拐脚处，甚至是凹凸点。

• 3M 521+电气绝缘树脂广泛用于各类中高压及密集型母排，作为其绝缘和防潮保护层。

2、产品性能•施工快速方便，中温快速固化，涂层均匀，外形美观。

•极好的电气特性。

•极好的耐热振和耐机械冲击性能。

Scotch-W eld TMEpoxy Potting Compound/AdhesiveDP270 Clear and BlackTechnical Data March 2019Product Description 3M TM Scotch-Weld TM Epoxy Potting Compound/Adhesive DP270 (or 3M™ Scotch-Weld™ Epoxy Potting Compound/Adhesive 270 B/A) is a two-part, low viscosityepoxy resin system designed primarily for potting, sealing, and encapsulation ofmany electronic components and is available in clear or black. 3M™ Scotch-Weld™epoxy potting compound/adhesive DP270 is noncorrosive to copper and offers goodthermal shock resistance and excellent retention of electrical insulation propertiesunder high humidity conditions.3M™ Scotch-Weld™ epoxy potting compound/adhesive DP270 has a work lifeof approximately 70 minutes, a tack-free time of about 3 hours and is fully curedafter 48 hours at 73°F (23°C). This product produces no exotherm in 5-10 grammasses and a very slight exotherm in larger masses.3M™ Scotch-Weld™ epoxy potting compound/adhesive DP270 is ideal for thepotting and encapsulation of many heat sensitive or delicate components such asglass diodes and sensors as well as for transformers, coils, chokes, relays, etc. It isavailable in the convenient 3M™ EPX Applicator System for multi-station usageand in bulk containers for larger volume applications.Available in bulk containers as Scotch-Weld epoxy potting compound/adhesive270 B/A.Features •Good Thermal Shock Resistance •Excellent Electrical Properties•Meets UL 94 HB (File No. E61941) •Noncorrosive to Copper•Long Worklife •Negligible ExothermTypical Uncured Properties Note: The following technical information and data should be considered representative3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 2 -Typical Cured PropertiesNote: The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 3 -D i s s i p a t i o n F a c t o rL o g o f R e s i s t a n c e (1 x 10 o h m s )*D i e l e c t r i c C o n s t a n tAdditional Electrical PropertiesNote: The following technical information and data should be considered representative ortypical only and should not be used for specification purposes.Dissipation Factor Versus Frequency Dielectric Constant Versus Frequency.030.025.020.015 3.83.63.43.2.010100Hz1 KHz10 KHz 100 KHz1 MHzFREQUENCY 3.0100Hz1 KHz10 KHz 100 KHz1 MHzFREQUENCYInsulation Resistance .8 mm/.8 mm Comb Pattern 60°C (140°F)/95% RH/100 V d.c.15141312112004006008001000HOURS1200*The numbers on the vertical axis represent the exponential power onthe 1 x 10 ohm notation.3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 4 -Typical CuredProperties (continued)Note: The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.Corrosion:Per ASTM D-3482(35°C/95°F/96% R.H./45V d.c./15 days) Pass - No copper corrosion Per 3M T est Method C-708(45°C/113°F/96% R.H./250V d.c./5 days) Pass - No copper corrosion (65°C/149°F/96% R.H./250V d.c./4 days) Pass - No copper corrosion Per Mil S-46163(10 days/50% R.H./23°C/73°F)Pass - No aluminum, brass or steel discoloration or corrosionSolvent Resistance:(Visual check after immersion in specified solvent at 23°C (73°F)Acetone1 Hour B 1 Month C Isopropyl Alcohol A B Freon TF A A Freon TMCB C 1,1,1-T richloroethane A C RMA FluxA BKey: A - UnaffectedB - Slight AttackC - Moderate/Severe AttackTypical Adhesive Performance CharacteristicsNote: The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.Although 3M ™ Scotch-Weld ™ Epoxy Potting Compound/Adhesive DP270 and 270 B/A can be used for many potting and encapsulation applications, they can also be used as adhesives. The following shows typical shear and peel values determined on several common substrates:Overlap Shear Adhesion (ASTM D-1002-72)90° T-Peel Adhesion (ASTM D-1876-61T)Compression Strength (ASTM D-695-68T)3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 5 -3M ™ EPXPneumatic Applicator Delivery Rates200 ml Applicator – Maximum Pressure 58 psi48.5/50 ml Applicator – Maximum Pressure 50 psi*Tests were run at a temperature of 70°F ± 2°F (21°C ± 1°C) and at maximum applicator pressure.Handling/Curing InformationDirections for Use1. For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, the amount of surface preparation directly depends on the required bond strength and the environmental aging resistance desired by user. For specific surface preparations on common substrates, see the section on surface preparation.2. These products consist of two parts.MixingFor Duo-Pak Cartridges3M™ Scotch-Weld ™ epoxy potting compound/adhesive DP270 Clear and Black are supplied in a dual syringe plastic duo-pak cartridge as part of the 3M ™ EPX Applicator systems. To use, simply insert the duo-pak cartridge into the EPX applicator and start the plunger into the cylinders using light pressure on the trigger. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If mixing of Part A and Part B is desired, attach the EPX applicator mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of material and mix thoroughly to obtain a uniform color.For Bulk ContainersMix thoroughly by weight or volume in the proportions specified in the typical uncured properties section to obtain a uniform color.3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 6 -Handling/CuringInformation (continued)3. For maximum bond strength apply product evenly to both surfaces to be joined.4. Application to the substrates should be made within 70 minutes. Larger quantities and/or higher temperatures will reduce this working time.5. Join the adhesive coated surfaces and allow to cure at 60°F (16°C) or above until firm. Heat up to 200°F (93°C) will speed curing.6. The following times and temperatures will result in a full cure of these products.23°C (73°F) 48 Hours 50°C (122°F) 4 Hours 80°C (176°F) 60 Minutes 100°C (212°F)30 Minutes7. Keep parts from moving during cure. Contact pressure necessary. Maximum shear strength is obtained with a 3-5 mil bond line. 8. Excess uncured adhesive can be cleaned up with ketone type solvents*.*Note: When using solvents, extinguish all ignition sources, including pilot lights,and follow the manufacturer ’s precautions and directions for use.Adhesion Coverage: A 0.005 in. thick bondline will yield a coverage of320 sq. ft./gallonApplication andEquipment SuggestionsThese products may be applied by spatula, trowel or flow equipment.Two part mixing/proportioning/dispensing equipment is available for intermittent or production line use. These systems are ideal because of their variable shot size and flow rate characteristics and are adaptable to most applications.3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 7 -Surface PreparationFor high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed. However, theamount of surface preparation directly depends on the required bond strength and the environmental aging resistance desired by user.The following cleaning methods are suggested for common surfaces:Steel1. Wipe free of dust with oil-free solvent such as acetone, isopropyl or alcohol solvents.*2. Sandblast or abrade using clean fine grit abrasives.3. Wipe again with solvent to remove loose particles.4. If a primer is used, it should be applied within 4 hours after surface preparation.Aluminum1. Alkaline Degrease: Oakite 164 solution (9-11 oz./gallon water) at 190°F ± 10°F (88°C ± 5°C) for 10-20 minutes. Rinse immediately in large quantities of cold running water.2. Acid Etch: Place panels in the following solution for 10 minutes at 150°F ± 5°F (66°C ± 2°C). Sodium Dichromate 4.1 - 4.9 oz./gallon Sulfuric Acid, 66°Be 38.5 - 41.5 oz./gallon 2024-T3 aluminum (dissolved) 0.2 oz./gallon minimum Tap water as needed to balance3. Rinse: Rinse panels in clear running tap water.4. Dry: Air dry 15 minutes; force dry 10 minutes at 150°F ± 10°F (66°C ± 5°C).5. If primer is to be used, it should be applied within 4 hours after surface preparation.Plastics/Rubber1. Wipe with isopropyl alcohol.*2. Abrade using fine grit abrasives.3. Wipe with isopropyl alcohol.*Glass1. Solvent wipe surface using acetone or MEK.*2. Apply a thin coating (0.0001 in. or less) of 3M ™ Scotch-Weld ™ Metal Primer EC3901 to the glass surfaces to be bonded and allow the primer to dry 60 minutes before bonding.*Note: When using solvents, extinguish all ignition sources, including pilot lights,and follow the manufacturer ’s precautions and directions for use.3M ™ Scotch-W eld ™Epoxy Potting Compound/Adhesive DP270 Clear and Black- 8 -StorageStore product at 60-80°F (16-27°C) for maximum storage life.Shelf LifeThese products when stored in original, unopened container have a shelf life of 18 months from date of manufacture.Precautionary InformationRefer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.Technical InformationThe technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information.Product Selection and UseMany factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to propertyWarranty,Limited Remedy, and DisclaimerUnless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3Mwarrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR APARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of LiabilityExcept for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.ISO 9001: 2000This Industrial Adhesives and T apes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards.Industrial Adhesives and Tapes Division3M Center, Building 225-3S-06 St. Paul, MN 55144-1000800-362-3550 • 877-369-2923 (Fax) /structuraladhesives3M and Scotch-Weld are trademarks of 3M Company. ©3M 2015。

3M™ Scotch-Seal™ Metal Sealant 2084Last Revision Date:July, 2014Product Features• 3M™ Scotch-Seal™ Metal Sealant 2084 is a one-part aluminum colored sealant which air dries to a tough, flexible film that resists water, oils and fuel.• Retains sealing properties after extended aging when painted.• Can be used to bond and seal aluminum to glass; also adheres well to many other metals and woods. Painting after curing is recommended, especially if sealed area will be subjected to UV exposure.Technical Information NoteThe following technical information and data should be considered representative or typical only and should not be used for specification purposes.Typical Physical PropertiesProperty Values Additional InformationSolids Content by Weight40 to 47 %Flash Point0 °F (-18 °C)ViewSolvent Resistance AcetoneViscosity7,000-22,500 cP ViewTypical Uncured Physical PropertiesProperty Values Additional InformationTypical Mixed Physical PropertiesProperty Values Additional InformationTack Free Time 5 minTypical Performance CharacteristicsProperty Values Additional Information180° Peel Adhesion43.8 N/cm (400 oz/in)ViewStorage and Shelf LifeFor optimum storage 3M™ Scotch-Seal™ Metal Sealant 2084 should be stored at 60-80°F (15-26°C). Higher temperatures reduce normal storage life. Lower temperatures cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.When stored at recommended temperature in original, unopened container, this product has a shelf life of 15 months from date of manufacture.Bottom Matter3MIndustrial Adhesives and Tapes Division3M Center, Building 225-3S-06 St. Paul, MN 55144-1000800-362-3550 • 877-369-2923 (Fax)TrademarksKenmar is a registered trademark of Kenmar, Inc. Graco is a registered trademark of Graco, Inc.Pyles is a registered trademark of Pyles, Inc.3M and Scotch-Seal are trademarks of 3M.Handling/Application InformationApplication EquipmentNote: Appropriate application equipment can enhance adhesive performance. We suggest the following application equipment for the user’s evaluation in light of the user’s particular purpose and method of application.Pump – 9 to 1 ratio double acting ball check type pump, 11.0 cu. inch per cycle with 41/4" air motor with single wiper follower plate. Packings, hoses and pail wiper must be compatible with acetone.Hose – Nylon lined, 500 psi working pressure.Reference InformationMaterial Temperature – 58°F (14°C)Note: Material pressure = operating air pressure x pump ratio.Flow Gun – Tip seal type.Manual Caulking Gun Filling – Kenmar® caulking gun loader with acetone resistant wiper; Graco® Model 225-975 gun loader with acetone resistant wiper; Pyles®Vaculoader.Chemical Resistance Requirements – Synthetic materials in contact with 3M™ Scotch-Seal™ Metal Sealant 2084 must be resistant to acetone. Polysulfide, butyl, nylon and PTFE are compatible.Directions for UseSurface Preparation: Best results are obtained on clean, dry surface. Oil, grease and other contaminants may be removed by wiping with a solvent such as isopropyl alcohol, MEK, acetone, or other locally compliant solvent.*Application: Production dispensing is best achieved with pressure-flow equipment. Hand caulking guns may also be used.Cleanup: Equipment and excess sealer may be cleaned with solvent such as isopropyl alcohol, MEK, acetone, or other locally compliant solvent.**Note: When using solvents for clean-up, extinguish all ignition sources and follow manufacturer’s precautions and directions for use when handling such materials. ReferencesProperty ValuesSafety Data Sheet SDS https:///3M/en_US/company-us/SDS-search/results/?gsaAction=msdsSRA&msdsLocale=en_US&co=ptn&q=2084Family GroupLink Tags:2084Precautionary InformationRefer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.InformationTechnical Information:The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information.Product Selection and Use:Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.Warranty, Limited Remedy, and Disclaimer:Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or Limitation of Liability:related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.Disclaimer:3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and limitations, and the user must take any action required under any recall, field action or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, or death. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert. For additional product information, visit .。

L2 Product Name (variable)Quick LinksFacilities WebsiteSafety Data Sheets (SDS)Some of these links lead to web-based resources that are not product-specific.Product DescriptionThe Scotch-Brite™ Clean & Shine Pad is a low-speed (175-600 RPM) scrubber pad for daily cleaning and virtually dustless polishing.•Cleans and shines in the same step, using only a low-speed scrubber.•Increases shine with repeated use and may result in reduction or elimination of burnishing.•Designed with contrasting color to provide visible wear indication.•Usable on both sides with the same proprietary coating.Special Features•Exceptional cleaning, mark removal and shine improvement (gloss and/or distinctness of image) with water only.•Designed for use on both sides for ease of use and extended life.•Compatible with water, detergents, or cleaners normally used for floor maintenance.•Color contrast between pad interior and surface coating provides wear indication.ApplicationsThis product is used for routine cleaning or light scrubbing under an auto scrubber or other standard low speed (175-600 RPM) floor cleaning equipment using water or detergent solution.For use on most finish-coated or uncoated flooring including; vinyl, sheet vinyl, LVT, VCT, rubber, linoleum, ceramic tile, marble, terrazzo, granite and concrete.Packaging and MarkingEach carton shall be labeled to identify the contents by product name, size, quantity and manufacturer. Each pad shall be printed with the product name.Standard SizesCircular discs and rectangles are available in a variety of common sizes. Pads are nominally one inch thick.Pad Use and CleaningDust mop entire floor prior to cleaning. Install appropriate sized Clean & Shine pad/s on your cleaning equipment. If using a rotary auto scrubber, a center hub attachment is required. Fill the scrubber tank with water or properly diluted cleaning solution. Clean floor.Pads may be rinsed with water to remove soil and debris as needed.StorageStore indoors in original packaging and under normal facility conditions.Product CharacteristicsThe Scotch-Brite™ Clean & Shine Pad is certified by Green Seal® for EnvironmentalInnovation based on a design for significantly improved initial performance compared to competitive products, extending the useful lifeof the floor pad and reducing solid waste generationScotch-Brite™ Clean and Shine Test Method Fiber TypePolyester N/A Weight (4 in. by 6 in.)22 gN/A O.D. Dimension Designated Size ± 1/16 in.N/A Thickness 1 in. nominal CCD0002Aggressiveness N/ACCD0020Packaging Recycle Content50-100% postconsumer recycled materialN/A© 3M 2021. All rights reserved.3M and Scotch-Brite are the trademark of 3M. Used under license in Canada.All other trademarks are property of their respective owners.Revision C, September 2021 Please recycle.Commercial Solutions3M Center, Building 220-12E-04St. Paul, MN 551441-800-626-8578/Facilityresult in serious injury or death.result in serious injury or deathexposure to contaminants:• DO NOT use this product on any asbestos-containing material.exposure to contaminants:• Ensure this product is used in the recommended applications with the suggested equipment.• Do not allow this product to be used by untrained operators.• Always follow standard safety practices, includingwearing appropriate protective apparel and eye protection, while using this product.Health and Safetymanufacturers' container labels and the Safety Data Sheets (SDS) for important health, safety and environmental information. To obtain SDS sheets for 3M products go to /SDS , or by mail or in case of an emergency, call 1- 888-364-3577 or 1-651-737-6501.When using any equipment, always follow the manufacturers' instructions for safe operation.Technical InformationThe technical information, guidance, and other statementscontained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information. If you have questions about this Product, contact the Customer Service Department at 1-800-626-8578.Product Selection and UseMany factors beyond 3M's control and uniquely within user'sknowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer's application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.Warranty, Limited Remedy, and DisclaimerUnless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES ORCONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price.Limitation of LiabilityExcept for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss ordamage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.。

Material Safety Data SheetCopyright, 2014, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.PRODUCT NAME: 3M Scotchcast™Flame-Retardant Compound 2131 (Parts A and B)MANUFACTURER: 3MDIVISION: Electrical Markets DivisionADDRESS: 3M Center, St. Paul, MN 55144-1000, USATelephone:1-888-3M HELPS (1-888-364-3577)Issue Date: 02/19/14Supercedes Date: 11/19/12Document Group: 28-8293-4ID Number(s):80-6114-6812-7, 80-6114-6813-5, 80-6114-6814-3, 80-6114-6815-0, 80-6114-6816-8, 80-6114-6817-6, 80-6114-6818-4, 80-6114-6819-2, 80-6114-6820-0, 80-6114-6821-8, 80-6114-6822-6, 80-6114-6823-4, 80-6114-6824-2, 80-6114-6825-9, 80-6114-6826-7, 80-6114-6874-7,80-6114-6875-4, 80-6114-6876-2, 80-6116-0620-5, 80-6116-0621-3This product is a kit or a multipart product which consists of multiple, independently packaged components. An SDS for each of these components is included. Please do not separate the component SDSs from this cover page. The document numbers of the SDSs for components of this product are:28-7650-6, 28-7666-2Revision Changes:Section 16: Disclaimer (first paragraph) information was modified.Section 16: Disclaimer (second paragraph) information was modified.Kit: Component heading paragraph information was modified.Section 16: Web address information was modified.Section 1: Address information was modified.Copyright information was modified.Telephone header information was modified.Company Telephone information was modified.DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M3M USA SDSs are available at Safety Data SheetCopyright,2014,3M Company.All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group:28-7666-2Version Number: 2.00Issue Date:02/19/14Supercedes Date: 06/24/111.1. Product identifier3M™Scotchcast™Flame Retardant Resin 2131 (PART B)Product Identification Numbers80-6114-6841-61.2. Recommended use and restrictions on useRecommended useElectrical, Part B of two part electrical resin1.3. Supplier’s detailsMANUFACTURER: 3MDIVISION: Electrical Markets DivisionADDRESS: 3M Center, St. Paul, MN 55144-1000, USATelephone:1-888-3M HELPS (1-888-364-3577)1.4. Emergency telephone number1-800-364-3577 or (651) 737-6501 (24 hours)2.1. Hazard classificationSerious Eye Damage/Irritation: Category 1.Carcinogenicity: Category 2.2.2. Label elementsSignal wordDangerSymbolsCorrosion | Health Hazard |PictogramsHazard StatementsCauses serious eye damage.Suspected of causing cancer.Precautionary StatementsPrevention:Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves and eye/face protection.Response:IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.Immediately call a POISON CENTER or doctor/physician.IF exposed or concerned: Get medical advice/attention.Storage:Store locked up.Disposal:Dispose of contents/container in accordance with applicable local/regional/national/international regulations. Notes to Physician:Not applicable2.3. Hazards not otherwise classifiedNone.8% of the mixture consists of ingredients of unknown acute oral toxicity.52% of the mixture consists of ingredients of unknown acute dermal toxicity.*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret.4.1. Description of first aid measuresInhalation:Remove person to fresh air. If you feel unwell, get medical attention.Skin Contact:Wash with soap and water. If signs/symptoms develop, get medical attention.Eye Contact:Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue rinsing. Immediately get medical attention.If Swallowed:Rinse mouth. If you feel unwell, get medical attention.4.2. Most important symptoms and effects, both acute and delayedSee Section 11.1. Information on toxicological effects.4.3. Indication of any immediate medical attention and special treatment requiredNot applicable5.1. Suitable extinguishing mediaIn case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.5.2. Special hazards arising from the substance or mixtureNone inherent in this product.Hazardous Decomposition or By-ProductsSubstance ConditionCarbon monoxide During CombustionCarbon dioxide During CombustionOxides of Nitrogen During CombustionOxides of Antimony During Combustion5.3. Special protective actions for fire-fightersNo unusual fire or explosion hazards are anticipated.6.1. Personal precautions, protective equipment and emergency proceduresVentilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Refer to other sections of this SDS for informationregarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.6.2. Environmental precautionsAvoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water.6.3. Methods and material for containment and cleaning upContain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriatesolvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and followsafety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible.7.1. Precautions for safe handlingDo not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to the environment. Use personal protective equipment (gloves, respirators, etc.) as required.7.2. Conditions for safe storage including any incompatibilitiesKeep container tightly closed. Keep cool. Store away from heat. Store in a dry place.8.1. Control parameters Occupational exposure limitsAmerican Indust. Hygiene Assoc : American Industrial Hygiene AssociationChemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended GuidelinesUS Dept of Labor -OSHA : United States Department of Labor -Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling8.2. Exposure controls8.2.1. Engineering controlsUse with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers.8.2.2. Personal protective equipment (PPE)Eye/face protectionSelect and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended:Full Face ShieldIndirect Vented GogglesSkin/hand protectionSelect and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing.Gloves made from the following material(s) are recommended: Polymer laminateRespiratory protectionAn exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure:Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulatesFor questions about suitability for a specific application, consult with your respirator manufacturer.9.1. Information on basic physical and chemical propertiesGeneral Physical Form: LiquidOdor, Color, Grade: Smooth black liquid with pungent odor.Odor threshold No Data AvailablepH Not ApplicableMelting point Not ApplicableBoiling Point> 290 ºFFlash Point> 290 ºF [Test Method: Closed Cup]Evaporation rate No Data AvailableFlammability (solid, gas)Not ApplicableFlammable Limits(LEL)No Data AvailableFlammable Limits(UEL)No Data AvailableVapor Pressure< 27 psia [@ 131 ºF]Vapor Density No Data AvailableDensity No Data AvailableSpecific Gravity 1.29 [Ref Std: WATER=1]Solubility in Water NilSolubility-non-water No Data AvailablePartition coefficient: n-octanol/ water No Data AvailableAutoignition temperature No Data AvailableDecomposition temperature No Data AvailableViscosity5,500 centipoiseVolatile Organic Compounds No Data AvailableVOC Less H2O & Exempt Solvents No Data Available10.1. ReactivityThis material is considered to be non reactive under normal use conditions.10.2. Chemical stabilityStable.10.3. Possibility of hazardous reactionsHazardous polymerization will not occur.10.4. Conditions to avoidNone known.10.5. Incompatible materialsNone known.10.6. Hazardous decomposition productsSubstance ConditionNone known.Refer to section 5.2 for hazardous decomposition products during combustion.The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole.11.1. Information on Toxicological effectsSigns and Symptoms of ExposureBased on test data and/or information on the components, this material may produce the following health effects: Inhalation:Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing,nasal discharge, headache, hoarseness, and nose and throat pain.Skin Contact:Contact with the skin during product use is not expected to result in significant irritation.Eye Contact:Corrosive (Eye Burns): Signs/symptoms may include cloudy appearance of the cornea, chemical burns, severe pain, tearing, ulcerations, significantly impaired vision or complete loss of vision.Ingestion:May be harmful if swallowed.Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.Carcinogenicity:Contains a chemical or chemicals which can cause cancer.Toxicological DataIf a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification.Reproductive ToxicityTarget Organ(s)Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components.Ecotoxicological informationPlease contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components.Chemical fate informationPlease contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components.13.1. Disposal methodsDispose of contents/ container in accordance with the local/regional/national/international regulations.Incinerate uncured product in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. As a disposal alternative, utilize an acceptable permitted waste disposal facility. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities.EPA Hazardous Waste Number (RCRA): Not regulated15.1. US Federal RegulationsContact 3M for more information.311/312 Hazard Categories:Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -Yes Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA): Ingredient C.A.S. No% by WtANTIMONY PENTAOXIDE (ANTIMONY1314-60-9 5 -10COMPOUNDS)15.2. State RegulationsContact 3M for more information.15.3. Chemical InventoriesThe components of this product are in compliance with the chemical notification requirements of TSCA.Contact 3M for more information.15.4. International RegulationsContact 3M for more information.NFPA Hazard ClassificationHealth:2 Flammability:1 Instability:0 Special Hazards:NoneNational Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also includethe toxic properties of combustion or decomposition products that are known to be generated in significant quantities.HMIS Hazard ClassificationHealth:2 Flammability:1 Physical Hazard:0 Personal Protection:X -See PPE section.Hazardous Material Identification System (HMIS® III) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS® III ratings are to be used with a fully implemented HMIS® III program. HMIS® is a registered mark of the American Coatings Association (ACA).Document Group:28-7666-2Version Number: 2.00Issue Date:02/19/14Supercedes Date: 06/24/11DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M3M USA SDSs are available at Safety Data SheetCopyright,2014,3M Company.All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2)neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group:28-7650-6Version Number: 3.00Issue Date:02/12/14Supercedes Date: 05/09/111.1. Product identifierScotchcast™Flame-Retardant Compound 2131 (Part A)Product Identification Numbers80-6114-6840-81.2. Recommended use and restrictions on useRecommended useElectrical, Part A of two part electrical resin1.3. Supplier’s detailsMANUFACTURER: 3MDIVISION: Electrical Markets DivisionADDRESS: 3M Center, St. Paul, MN 55144-1000, USATelephone:1-888-3M HELPS (1-888-364-3577)1.4. Emergency telephone number1-800-364-3577 or (651) 737-6501 (24 hours)2.1. Hazard classificationAcute Toxicity (inhalation): Category 3.Serious Eye Damage/Irritation: Category 2A.Skin Corrosion/Irritation: Category 2.Respiratory Sensitizer: Category 1.Skin Sensitizer: Category 1.Specific Target Organ Toxicity (respiratory irritation): Category 3.Specific Target Organ Toxicity (repeated exposure): Category 1.2.2. Label elementsSignal wordDangerSymbolsSkull and crossbones | Exclamation mark | Health Hazard |PictogramsHazard StatementsToxic if inhaled.Causes serious eye irritation.Causes skin irritation.May cause allergy or asthma symptoms or breathing difficulties if inhaled.May cause an allergic skin reaction.May cause respiratory irritation.Causes damage to organs through prolonged or repeated exposure:respiratory system |Precautionary StatementsPrevention:Do not breathe dust/fume/gas/mist/vapors/spray.Use only outdoors or in a well-ventilated area.In case of inadequate ventilation wear respiratory protection.Wear eye/face protection.Wear protective gloves.Do not eat, drink or smoke when using this product.Wash thoroughly after handling.Contaminated work clothing must not be allowed out of the workplace.Response:IF INHALED: Remove person to fresh air and keep comfortable for breathing.If experiencing respiratory symptoms: Call a POISON CENTER or doctor/physician.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.If eye irritation persists: Get medical advice/attention.IF ON SKIN: Wash with plenty of soap and water.If skin irritation or rash occurs: Get medical advice/attention.Take off contaminated clothing and wash it before reuse.Call a POISON CENTER or doctor/physician if you feel unwell.Storage:Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with applicable local/regional/national/international regulations.2.3. Hazards not otherwise classifiedPersons previously sensitized to isocyanates may develop a cross-sensitization reaction to other isocyanates.21% of the mixture consists of ingredients of unknown acute oral toxicity.32% of the mixture consists of ingredients of unknown acute inhalation toxicity.*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret.4.1. Description of first aid measuresInhalation:Remove person to fresh air. Get medical attention.Skin Contact:Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention.Eye Contact:Immediately flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. Get medical attention.If Swallowed:Rinse mouth. If you feel unwell, get medical attention.4.2. Most important symptoms and effects, both acute and delayedSee Section 11.1. Information on toxicological effects.4.3. Indication of any immediate medical attention and special treatment requiredNot applicable.5.1. Suitable extinguishing mediaIn case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.5.2. Special hazards arising from the substance or mixtureClosed containers exposed to heat from fire may build pressure and explode.Hazardous Decomposition or By-ProductsSubstance ConditionCarbon monoxide During CombustionCarbon dioxide During CombustionHydrogen Cyanide During CombustionOxides of Nitrogen During Combustion5.3. Special protective actions for fire-fightersNo unusual fire or explosion hazards are anticipated.6.1. Personal precautions, protective equipment and emergency proceduresEvacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Observe precautions from other sections.6.2. Environmental precautionsAvoid release to the environment.6.3. Methods and material for containment and cleaning upContain spill. Pour isocyanate decontaminant solution (90% water, 8% concentrated ammonia, 2% detergent) on spill and allow to react for 10 minutes. Or pour water on spill and allow to react for more than 30 minutes. Cover with absorbent material. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a container approved for transportation by appropriate authorities, but do not seal the container for 48 hours to avoid pressure build-up. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Cover, but do not seal for 48 hours. Dispose of collected material as soon as possible.7.1. Precautions for safe handlingFor industrial or professional use only. Do not use in a confined area with minimal air exchange. Do not breathedust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before reuse.7.2. Conditions for safe storage including any incompatibilitiesStore in a well-ventilated place. Keep cool. Keep container tightly closed to prevent contamination with water or air. If contamination is suspected, do not reseal container. Protect from sunlight. Store away from heat. Store away from strong from areas where product may come into contact with food or pharmaceuticals. Store in a dry place.bases.Store awayOccupational exposure limitsAmerican Indust. Hygiene Assoc : American Industrial Hygiene AssociationChemical Manufacturer Rec Guid : Chemical Manufacturer's Recommended GuidelinesUS Dept of Labor -OSHA : United States Department of Labor -Occupational Safety and Health AdministrationTWA: Time-Weighted-AverageSTEL: Short Term Exposure LimitCEIL: Ceiling8.2. Exposure controls8.2.1. Engineering controlsUse general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. 8.2.2. Personal protective equipment (PPE)Eye/face protectionSelect and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended:Indirect Vented GogglesSkin/hand protectionSelect and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing.Gloves made from the following material(s) are recommended: Butyl RubberFluoroelastomerPolymer laminateIf this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an exposure assessment. The following protective clothing material(s) are recommended: Apron –Butyl rubberApron -polymer laminateRespiratory protectionAn exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure:Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulatesFor questions about suitability for a specific application, consult with your respirator manufacturer.。

CARTON SEALING TAPESCARTON SEALINGFor “problem” applicationslike high recycled contentsmooth cartons, dusty and/NATURAL RUBBER8TAPE DISPENSERSFor shipping, packing, sealingbags, bonding substrates or10Improves the overallappearance and impact ofyour packages by addingyour brand and marketingmessage.10Automation – it’s about time!IPG has a wide variety of cartonsealing machines available tohelp bring the speed to yourpackaging operation.IPG | 100 Paramount Drive | Suite 300 | Sarasota, FL 34232HOT MELTIntertape® brand Hot Melt Carton Sealing Tapes offer the widest range of application flexibility available. They offer excellent processing performance whether manually or automatically applied. Their superior adhesion properties, holding force, tensile strength and easy unwind ensure consistent, reliable seals to variety of corrugated and linerboard boxes.NATURAL RUBBERIPG®’s Natural Rubber Carton Sealing Tapes have the most aggressive adhesive available. They offer fast, positive bonding on “problem” applications such as high recycled content cartons, rough or ultra-smooth cartons, heavy ink coverage, dusty and/or dirty environments, humid conditions and temperature extremes.NATURAL RUBBER ADHESIVE* Limited sizes available in Tan as a non-stock, make-to-order item.Intertape® brand Acrylic Carton Sealing Tapes best suited for reliable, all-temperaturebox sealing performance (less than 40ºF and greater than 120ºF) where resistance toaging, weathering, UV light and yellowing are important. They also provide excellentclarity, high shear strength to prevent “flagging,” superior quick stick performance andcontrolled unwind to facilitate dispensing on manual or automatic case sealing machines. ACRYLIC ADHESIVEACRYLICFinding the right dispenser type for your needs has never been easier with our full line of tapedispensers from IPG ®. Our selection of dispensers ranges from general purpose to heavy-duty. Whether you’re shipping, packing, sealing bags, bonding substrates or dispensing labels, we have a solution of hand-held and desktop dispensers in many sizes and types for all your needs.Ergonomically designed to reduce fatigue and provides a comfort molded finger grip.ACRYLIC SIZESSTYLE 191300HAND LENGTHmm x m 48 x 10072 x 10048 x 5048 x 10072 x 10048 x 50rolls/carton362436362436MACHINE LENGTH mm x m 48 x 91448 x 137172 x 91448 x 91448 x 914rolls/carton66466TAPE DISPENSERSDesigned to fit tape with any size core and are excellent for applying carton sealing, filament, masking, flatback tapes and more. Reduces noise and is quieter on the tape unwind.STYLEDESCRIPTIONGRADECORE DIAMETER MAX WIDTH OF TAPEMAXDIAMETER OF TAPE COLOR inchesinches inches 1972Lightweight steel frame with high impact plastic; plastic roller; heavy gauge reversible steel blade; adjustable friction tension brake for the tape roll; spring loaded tape gate; flexible poly tape wiperUtility 33 5.5Blue TPX48NP XTRAtape™; Fit 1.5” ID core; reinforce steel frame with high impact plastic;plastic roller; adjustable brake for tension control; plastic wiperMedium1.524.76BluePISTOL GRIP HAND DISPENSERSCustom printed tape improves the overall appearance and impact of your packages by adding logos, QR codes, and messaging for your company and products. IPG ® offers a wide variety of cost-efficient custom printed and standard designs.CASE SEALING MACHINERYIPG is a major integrated provider of both pressure-sensitive tape and case sealing machinery. We are committed to providing timely system solutions and have wide variety of standard case sealing machinery for quick delivery.The modular design of each Interpack ™ case taper combined with superior features and materials will provide flawless performance for many years to come. Standard machines are available in most drive styles and can be outfitted with either 2" or 3" wide ET 2Plus or ET Xtreme taping heads. Heavy duty construction, oversized gearmotors, and low maintenance are the hallmarks of the Interpack ™ machinery line.Learn more about IPG’s machinery line: /interpackPRINTED CARTON SEALING TAPEFEATURES & BENEFITS **Lower carbon footprint than traditional carton sealing tapes170e Film for this tape is made with 30%R E C YC L E D MATERIALS• Same price, same performance, less carbon footprint • Water-based acrylic adhesive• Broad application temperature range• Excellent UV resistance• Quick adhesion to corrugate• Conformable film backing• Great for long term storage• In stock and availableNE W For tech data and size information see page 7CORPORATE PROFILEHeadquartered in Sarasota, Florida, IPG is a global provider of packaging and protective solutions across a diversified set of geographies and end-markets. The Company develops, manufactures, and sells a variety of solutions including paper and film-based pressure-sensitive and water-activated tapes, stretch and shrink films, protective。

产品信息：Duo-Pak卡式胶筒装3M Scotch-Weld胶粘剂3MDP-100透明规格：50ML/支12支/盒(光纤跳线的固定，通用传感器的封装) 特性：●快速固化胶粘剂●硬质环氧树脂●15~20分钟达到操作强度●可机械施工产品混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：1300075°F （24°C）时的操作时间近似值：4分钟75°F （24°C）时的T型剥离（PIW）：2重叠剪切强度（PSI）：1．-67°F（-55°C）：9002．75°F （24°C）：15003．180°F（82°C）：3004．250°F（121°C）：2003M DP-100 Plus 透明规格：50ML/支12支/盒(光纤跳线的固定)特性：●清澈透明●快速固化硬质环氧树脂●良好的剥离和剪切强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：850075°F （24°C）时的操作时间近似值：4分钟75°F （24°C）时的T型剥离（PIW）：13重叠剪切强度（PSI）：1．-67°F（-55°C）：30002．75°F （24°C）：35003．180°F（82°C）：2004．250°F（121°C）：1503M DP-100NS 半透明规格：50ML/支12支/盒(连接器的接口的加强保护) 特性：●25~30分钟达到操作强度●半透明低流动性的DP-100胶粘剂混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：9500075°F （24°C）时的操作时间近似值：6分钟75°F （24°C）时的T型剥离（PIW）：2重叠剪切强度（PSI）：1．-67°F（-55°C）：9002．75°F （24°C）：15003．180°F（82°C）：3004．250°F（121°C）：2003M DP-100FR 白色规格：50ML/支12支/盒(变压器线圈的固定)特性：●25~30分钟达到操作强度●满足UL94V-0额定值●自熄型的DP100胶粘剂混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：5000075°F （24°C）时的操作时间近似值：6分钟75°F （24°C）时的T型剥离（PIW）：2重叠剪切强度（PSI）：1．-67°F（-55°C）：8002．75°F （24°C）：14003．180°F（82°C）：4004．250°F（121°C）：2003M DP-105 透明规格：50ML/支12支/盒(LED相关部件的密封保护)特性：●清澈透明●快速固化●极其柔性●优异的剥离强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：650075°F （24°C）时的操作时间近似值：5分钟75°F （24°C）时的T型剥离（PIW）：35重叠剪切强度（PSI）：1．-67°F（-55°C）：35002．75°F （24°C）：20003．180°F（82°C）：1504．250°F（121°C）：1003M DP-110灰色规格：50ML/支12支/盒特性：●快速固化胶粘剂●柔性环氧树脂●30分钟达到操作强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：55000 75°F （24°C）时的操作时间近似值：9分钟75°F （24°C）时的T型剥离（PIW）：15重叠剪切强度（PSI）：1．-67°F（-55°C）：20002．75°F （24°C）：25003．180°F（82°C）：2004．250°F（121°C）：1503M DP-110半透明规格：50ML/支12支/盒特性：●30分钟达到操作强度●DP-110灰色胶粘剂的半透明型混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：50000 75°F （24°C）时的操作时间近似值：9分钟75°F （24°C）时的T型剥离（PIW）：10重叠剪切强度（PSI）：1．-67°F（-55°C）：20002．75°F （24°C）：25003．180°F（82°C）：2004．250°F（121°C）：1503M DP-125灰色规格：50ML/支12支/盒特性：●中等操作时间●良好的剥离强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：52500 75°F （24°C）时的操作时间近似值：25分钟75°F （24°C）时的T型剥离（PIW）：35重叠剪切强度（PSI）：1．-67°F（-55°C）：34002．75°F （24°C）：43003．180°F（82°C）：4004．250°F（121°C）：2003M DP-125半透明规格：50ML/支12支/盒特性：●中等操作时间●良好的剥离强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：1500075°F （24°C）时的操作时间近似值：25分钟75°F （24°C）时的T型剥离（PIW）：35重叠剪切强度（PSI）：1．-67°F（-55°C）：40002．75°F （24°C）：25003．180°F（82°C）：1504．250°F（121°C）：1003M DP-190灰色规格：50ML/支12支/盒（连接器的封装，防水，防尘）特性：●长操作时间胶粘剂●柔性环氧树脂●8~12小时达到操作强度●可粘接金属、塑料和其他许多不同类的材料混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：8000075°F （24°C）时的操作时间近似值：90分钟75°F （24°C）时的T型剥离（PIW）：20重叠剪切强度（PSI）：1．-67°F（-55°C）：15002．75°F （24°C）：25003．180°F（82°C）：4004．250°F（121°C）：3003M DP-190半透明规格：50ML/支12支/盒（连接器的封装，防水，防尘）特性：●长操作时间●良好的剥离强度混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：1000075°F （24°C）时的操作时间近似值：90分钟75°F （24°C）时的T型剥离（PIW）：30重叠剪切强度（PSI）：1．-67°F（-55°C）：35002．75°F （24°C）：17003．180°F（82°C）：1604．250°F（121°C）：1003M DP-270 黑色规格：50ML/支12支/盒（医用传感器的封装，电子零件的封装）特性：●长操作时间封装化合物●8~12小时达到操作强度●硬质环氧树脂混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：1900075°F （24°C）时的操作时间近似值：70分钟75°F （24°C）时的T型剥离（PIW）：2重叠剪切强度（PSI）：1．-67°F（-55°C）：12002．75°F （24°C）：25003．180°F（82°C）：3004．250°F（121°C）：2003M DP-270 透明规格：50ML/支12支/盒特性：●DP-270胶粘剂的透明型●可用于许多电子应用场合混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：1900075°F （24°C）时的操作时间近似值：70分钟75°F （24°C）时的T型剥离（PIW）：2重叠剪切强度（PSI）：1．-67°F（-55°C）：12002．75°F （24°C）：25003．180°F（82°C）：3004．250°F（121°C）：2003M DP-420灰白色规格：37ML/支12支/盒特性：●中等操作时间的坚韧型环氧树脂●1~2小时达到操作强度●高性能混合比（容积）B：A：2：1粘度近似值75°F （24°C）（CPS）：4500075°F （24°C）时的操作时间近似值：20分钟75°F （24°C）时的T型剥离（PIW）：50重叠剪切强度（PSI）：1．-67°F（-55°C）：45002．75°F （24°C）：45003．180°F（82°C）：4504．250°F（121°C）：2003M DP-420黑色规格：37ML/支12支/盒（高尔夫球头的LOGO的粘接，传感器零部件的组装）特性：●DP-420灰白色胶粘剂的黑色派生型●牢固耐久的结构粘接混合比（容积）B：A：2：1粘度近似值75°F （24°C）（CPS）：2250075°F （24°C）时的操作时间近似值：15分钟75°F （24°C）时的T型剥离（PIW）：50重叠剪切强度（PSI）：1．-67°F（-55°C）：45002．75°F （24°C）：45003．180°F（82°C）：29804．250°F（121°C）：5703M DP-460灰白色规格：37ML/支12支/盒（碳纤维类运动器材的粘接）特性：●长操作时间的坚韧型环氧树脂●2~4小时达到操作强度●满分足MIL-A-23941A标准混合比（容积）B：A：2：1粘度近似值75°F （24°C）（CPS）：450075°F （24°C）时的操作时间近似值：60分钟75°F （24°C）时的T型剥离（PIW）：60重叠剪切强度（PSI）：1．-67°F（-55°C）：45002．75°F （24°C）：45003．180°F（82°C）：7004．250°F（121°C）：2003M DP-460NS 灰白色规格：37ML/支12支/盒特性：●不流挂型DP-460胶粘剂●可热固化●高性能混合比（容积）B：A：2：1粘度近似值75°F （24°C）（CPS）：125000 75°F （24°C）时的操作时间近似值：60分钟75°F （24°C）时的T型剥离（PIW）：60重叠剪切强度（PSI）：1．-67°F（-55°C）：49002．75°F （24°C）：46503．180°F（82°C）：26304．250°F（121°C）：4203M DP-4XL 灰白色规格：37ML/支12支/盒特性：●超长操作时间坚韧型环氧树脂，用于大型组件●250°F时F5分钟达到操作强度混合比（容积）B：A：2：1粘度近似值75°F （24°C）（CPS）：22500 75°F （24°C）时的操作时间近似值：5-6小时75°F （24°C）时的T型剥离（PIW）：60重叠剪切强度（PSI）：1．-67°F（-55°C）：28002．75°F （24°C）：48803．180°F（82°C）：12404．250°F（121°C）：2803M DP-605NS 灰白色规格：50ML/支12支/盒特性：●快速固化半硬质聚氨酯●15-20分钟达到操作强度●缝隙填充剂●用于木材和塑料时不流淌混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：15000075°F （24°C）时的操作时间近似值：4分钟75°F （24°C）时的T型剥离（PIW）：15重叠剪切强度（PSI）：1．-67°F（-55°C）：10002．75°F （24°C）：12503．180°F（82°C）：3254．250°F（121°C）：1003M DP-640棕色规格：50ML/支12支/盒特性：●不流挂●长操作时间●牢固而柔性的粘接混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：2500075°F （24°C）时的操作时间近似值：40分钟75°F （24°C）时的T型剥离（PIW）：25重叠剪切强度（PSI）：1．-67°F（-55°C）：25002．75°F （24°C）：20003．180°F（82°C）：3004．250°F（121°C）：1503M DP-805 淡黄色规格：50ML/支12支/盒特性：●高剥离强度和剪切强度●温度性能好●可粘接稍带油质的材料●优异的塑料粘接力混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：11000075°F （24°C）时的操作时间近似值：4分钟75°F （24°C）时的T型剥离（PIW）：35重叠剪切强度（PSI）：1．-67°F（-55°C）：25002．75°F （24°C）：35003．180°F（82°C）：22004．200°F（93°C）：2003M DP-810 透明，黑色规格：50ML/支12支/盒（电脑外壳的粘接，传感器的组装）特性：●可粘接许多种金属和塑料●无需表面预处理●能非常快速地达到粘接强度●6小时内完全固化混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：2000075°F （24°C）时的操作时间近似值：8-10分钟75°F （24°C）时的T型剥离（PIW）：30重叠剪切强度（PSI）：1．-67°F（-55°C）：12002．75°F （24°C）：42003．180°F（82°C）：5004．200°F（93°C）：3003M DP-818 灰色规格：50ML/支24支/盒（通讯机柜零件的粘接）特性：●对金属塑料和许多其他材料具有优良的粘结性能●室温快速固化，较好韧性●可粘接轻微油污的金属表面，不必表面处理混合比（容积）B：A：1：175°F （24°C）时的操作时间近似值：15分钟75°F （24°C）时的T型剥离（PIW）：26重叠剪切强度（PSI）：-67°F（-55°C）：14103M DP-820 黄色特性：●高剪切强度和剥离强度●可粘接稍带油质的金属●中等操作时间混合比（容积）B：A：1：1粘度近似值75°F （24°C）（CPS）：6000075°F （24°C）时的操作时间近似值：15-20分钟75°F （24°C）时的T型剥离（PIW）：22重叠剪切强度（PSI）：1．-67°F（-55°C）：31002．75°F （24°C）：31503．180°F（82°C）：19004．200°F（93°C）：14503M DP-8005 半透明规格：35ML/支12支/盒（用于比较难粘材料的粘接，如：尼龙，PP等）特性：●结构性粘接聚烯烃●无需表面预处理●优异的环境耐受能力●2~3小时达到操作强度混合比（容积）B：A：10：1粘度近似值75°F （24°C）（CPS）：2750075°F （24°C）时的操作时间近似值：2.5-3分钟75°F （24°C）时的T型剥离（PIW）：16重叠剪切强度（PSI）：1．-67°F（-55°C）：20002．180°F（82°C）：3403M DP-490 黑色规格：50ML/支12支/盒混合比（容积）B：A：2：13M DP-760 白色规格：50ML/支12支/盒混合比（容积）B：A：2：13M TM Scotch-Weld TM电子产品级环氧树脂胶粘剂高性能，专用于要求严格的电子产品应用对于关注胶粘剂粘接处的溢气和腐蚀情况的那些精密电子产品组装，可以用先进的Scotch-Weld电子级（EG）环氧树脂来替代机械式紧固件和低等级的胶粘剂，进行产品的组装。

Scotch®Performance Flatback Tape3M2525Technical DataProduct Description Scotch®Performance Flatback Tape 2525 is used in holding, splicing or masking applications where high adhesion strength, high temperature capability and high backing strength are required.Typical PhysicalPropertiesNote: The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.ASTM Test Method Adhesion to Steel: 69 oz./in. width (75 N/100 mm) D-3330Tensile Strength: 49 lbs./in. width (858 N/100 mm) D-3759 Elongation at Break: 2% D-3759Tape Thickness: 9.5 mils (0.241 mm) D-3652 Temperature Use Range: Up to 300°F (149°C)Feature•Has excellent adhesion and backing strength levels and is resistant to moistconditions.•Can be used for applications where a colored backing is desired and willwithstand a bake cycle of 300°F (149°C) for one hour.•Not recommended for outdoor applications or prolonged periods of sunlightexposure as tape may become very difficult to remove.Application Ideas•Can be used in many holding, masking and splicing applications where a highvisibility tape is desired. It can also be used for various types of edging andbinding applications.StorageStore under normal conditions of 70°F (21°C) and 50% R.H. in the original carton.Shelf LifeTo obtain best performance, use this product within 12 months from date ofmanufacture.Product UsAll statements, technical information and recommendations contained in this document are based upontests or experience that 3M believ es are reliable. However, many factors beyond 3M’s control can affectthe use and performance of a 3M product in a particular application, including the conditions underwhich the product is used and the time and environmental conditions in which the product is expected toperform. Since these factors are uniquely within the user’s knowledge and control, it is essential that theuser evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for theuser’s method of application.Warranty andLimited RemedyUnless stated otherwise in 3M’s product literature, packaging inserts or product packaging for individualproducts, 3M warrants that each 3M product meets the applicable specifications at the time 3M ships theproduct. Individual products may have additional or different warranties as stated on product literature,package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED,INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESSFOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OFDEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the 3M productis fit for a particular purpose and suitable for user’s application. If the 3M product is defective within thewarranty period, your exclusive remedy and 3M’s and seller’s sole obligation will be, at 3M’s option, toreplace the product or refund the purchase price.Limitation of LiabilityExcept where prohibited by law, 3M and seller will not be liable for any loss or damage arising from the3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theoryasserted, including warranty, contract, negligence or strict liabilityThis Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001:2000 standards。