海洋工程技术词汇中英文对照

Electric heating cable 加热电缆field development 油田开发flexible riser 挠性隔水管heating line 加热管线…host‟ platform “主”平台…surface‟ conductor “表层”导管“dual bore” type tree “双筒”型采油树“temporary” guide base “临时”导向基座“two stack” approach “双防喷器组”法Abandonment and Recovery 弃置与回收acceptance criteria 验收标准Acceptance Test 验收测试accumulator bottle 蓄能器瓶alignment 找正alternating current 交流电ambient seawater temperature 周围海水温度ambient temperature 环境温度ancillary equipment 辅助设备annular space 环形空间annulus bore 环空孔annulus master valve 环空主阀annulus seal assembly 环空密封总成anti-rotation pin 防旋转销armour wire 铠装线armours layer 铠装层artificial lift 人工举升artificial lift method 人工举升法Asgard project Asgard项目Atmospheric Diving Suit 常压潜水服atmospheric pressure 大气压力attachement point 固着点Austenitic Stainless Steel 奥氏体不锈钢austenitic-ferric steel 奥氏体-铁素体钢auto depth 自动定深automatic connector 自动连接器average unevenness height 平均不均匀高度axial tension 轴向拉力backing steel 背钢backup function 备份功能barrier coating 防护涂层barrier protection 隔层保护basic oxygen furnace 碱性氧气转炉basket storage carousel 篮式存管盘bend limiter 弯曲限幅器bend radius 弯曲半径bend restrictor 弯曲限制器bend stiffener 弯曲加强杆bending loads 弯曲载荷bending moment 弯曲力矩bending reaction ring 弯曲止推环bending stiffness 抗弯刚度bending stress 弯曲应力Billet piercing process 坯板料穿孔工艺bleed valve 泄放阀blind cap 盲帽block valves 断流阀bypass valves 旁通阀Blowout Preventer 防喷器bollard pull 系缆拉力bolt flange connection 螺栓法兰连接bolted flange connection 螺栓法兰连接BOP connector 防喷器连接器BOP pipe ram 防喷器管闸板BOP Stack 防喷器组Bore Protector 井筒保护器bottom crawling vehicle 海底爬行车Buckle propagation 弯曲传播buckle propagation 弯曲传播Bull Nose 圆头管堵bundle 管束buoyancy module 浮力块Campos basin Campos盆地carbon steel 碳钢Carbon steel tube 碳钢管Carbon-Manganese steel pipe 碳锰钢管carrier pipe 输送管Casing Hanger 套管悬挂器casing pup joint 套管短节catenary curve 悬链曲线catenary shape 悬链线型cathodic protection 阴极保护detection system 检测系统Centrifugation Process 离心工艺Check Valve 止回阀chemical fluids 化学流体chemical injection 化学剂注入choke actuator 油嘴促动器choke insert 油嘴嵌件choke position 油嘴位置circuit breaker 断路器circuit length 电路长度circulate hot water 循环热水clad corrosion resistant alloy 复合防腐合金Clad Metal 复合金属clad pipe structure 复合管结构Clad pipe system 复合管系统clamp connector 紧固连接器clamp hub 卡箍Class I 第一类Class II 第二类Class III 第三类Class IV 第四类C-Mn steel pipe 碳锰钢管coating defect 涂层缺陷Coil tubing 连续油管coiled skelp 挠性管材collet connection 套管连接collet connector 套管连接器Completion / Workover Riser System 完井/修井隔水管系统completion equipment 完井设备completion guide base 完井导向基座Completion Guidebase 完井导向基座completion riser system 完井隔水管系统Component Change-Out tool 部件更换工具composite armour 复合铠装composite armour layer 复合铠装层composite material 复合材料compression force 压缩力compressive load 压缩载荷concentric tubing hanger 同心油管悬挂器Conductor Housing 导管头conductor resistance 导体电阻conductor string 导管柱Connection/reaction loads 连接/反作用载荷Connector profile 连接器剖面Continuous lamination 连续分层continuous length 连续长度continuous slab caster 板坯连铸机continuous strand caster 流坯连铸机control cabin 控制舱control fluid 压井液Control Function 控制功能Control junction plate 控制连接板control module 控制模块control pod 控制盒control room 控制室Control Station 控制站control umbilical 控制脐带管control valve 控制阀conventional style trees 常规型采油树Conventional Tree 常规采油树correct orientation 正确方向corrosion allowance 腐蚀裕量corrosion control 腐蚀控制corrosion inhibition 腐蚀抑制corrosion inhibitor 缓蚀剂CORROSION MONITORING 腐蚀监控corrosion protection 腐蚀防护corrosion protection system 腐蚀防护系统corrosion rate 腐蚀速度corrosion resistance 耐腐蚀corrosion resistant alloy 耐腐蚀合金corrosion resistant materials 耐腐蚀材料corrosive agent 腐蚀剂corrosive environment 腐蚀性环境coupler hydraulic 接头液压CROSS SECTION 截面cross sectional area 截面面积Cross Wound Polyethylene 交叉卷绕聚乙烯cross-flow oscillations 横流振动cross-section 截面crushing load 压碎载荷residual strain 残余应变Cumulative strain deformation 累积应变变形cumulative strain 累积应变current drag 海流阻力Current Limiter 限流器current loads 海流载荷current saturation 当前饱和current velocity 海流速度cylindrical billet 圆柱坯料data collection 数据采集data sheets 数据表data transmission 数据传输DC conductor resistance 直流导体电阻Dead Weight 船舶载重量debris cap 岩屑帽deck level 甲板水平面deck load 甲板载荷Deck space 甲板空间deep water 深水deepwater developments 深水开发deepwater field development 深水油气田开发DEEPWATER FIELD DEVELOPMENT REFERENCE BOOK 深水油气田开发参考手册deepwater flowline 深水出油管线deepwater pipeline 深水管道DEEPWATER REFERENCE BOOK 深水参考手册deepwater riser 深水隔水管Destructive Examination 破坏性检验development option 开发方案Differential Global Positioning System 差分全球定位系统Differential Pressure 压力差Digging chain 开挖链direct current 直流Direct Heating System 直接加热系统Directional Control Valve 方向控制阀Distributed Control System 分布式控制系统distribution piping systems 分配管道系统distribution system 配电系统Distribution Unit 分配装置Diving Support Vessel 潜水供应船Dolly base 转管滚座downhole gauges 井下压力计Downhole Pressure 井下压力Downhole Safety Valve 井下安全阀drag loads 拉力载荷drill pipe string 钻杆柱drilling operation 钻井作业drilling riser 钻井隔水管Driving wheel 驱动轮Dual Bore Split Body Tree 双筒拼合本体采油树dual bore subsea tree 双筒水下采油树dual bore tree 双筒采油树dual redundant 双冗余dual SEMs 双SEMDual Systems 双机系统Duplex stainless pipe 双相不锈钢管Duplex stainless steel 双相不锈钢Dynamic analysis 动态分析Dynamic positioning 动力定位dynamic positioning (DP) system 动力定位系统dynamic positioning system 动力定位系统dynamic response 动态响应dynamic riser 动力隔水管dynamically positioned lay vessel 动力定位铺管船Earth continuity test 接地连续性试验Edge trimming 切边edge-crimping 卷边Effective tension 有效张力electric cable 电缆electric current 电流electric heating 电加热electric power 电力Electric Power Unit 电力装置electric pump 电动泵electric resistance welded 电阻焊Electric resistance welded pipe 电阻焊管electric submersible pump 电动潜油泵electrical cable 电缆electrical component 电气部件electrical conductor 电气导线Electrical connection 电气连接electrical connector 电气连接件electrical current 电流Electrical Distribution Unit 配电装置Electrical electrode 电极Electrical Flying Lead 电引线Electrical isolation 电气隔离Electrical Jumper 电气跨接线Electrical junction box 电气接线盒electrical motor 电动机electrical noise 电噪音Electrical penetrators 电动穿孔器Electrical Power Unit 电力装置ELECTRICAL POWER UNIT 电力装置（EPU）electrical pump 电动泵Electrical signal 电信号Electrical Umbilical 电气脐带管electric-arc furnace 电弧炉electric-welded pipe 电焊接管electro-hydraulic control systems 电动液压控制系统electro-hydraulic multiplexed subsea control system 电动液压多路复用水下控制系统Electro-hydraulic umbilical 电动液压脐带管electronic components 电子元件Emergency Shut Down 应急关断empirical curve 经验曲线empirical uplift coefficient 经验上提系数end fitting 端部配件end riser termination 端部隔水管终端environment loads 环境载荷environmental condition 环境条件environmental loads 环境载荷ERW line pipe 电阻焊管线ESD sequence 应急关断顺序ESD signal 应急关断信号export line 输送管线external corrosion 外部腐蚀external diameter 外径external hydrostatic pressure 外部静水压力external pressure 外部压力External Welding 外部焊接Extrusion Process 挤压工艺Extrusion throat 挤压式喉管fabrication 制造fabrication times 制造时间Factory Acceptance Test 工厂验收试验fatigue damage 疲劳损坏fatigue life 疲劳寿命female connector 母连接器female couplers 母接头female couplings 母接头fibre optic 光纤fibre optic cables 光纤电缆fibre optic technology 光纤技术field development 油气田开发field joint 现场连接接头field life 油田寿命Field Signature Method (FSM) stations FSM技术检测点（备注：FSM是挪威CorrOcean公司开发的一种新型无损检测技术）final position 最终位置Firing line 流水作业线first-line barrier protection 一级隔层保护Flex joint 挠性接头flexible flowline 挠性出油管线flexible jumper 挠性跨接管flexible laying system 挠性管铺设系统flexible line 挠性管线flexible pipe flowlines 挠性出油管线flexible pipe structure 挠性管结构Flexible pipe system 挠性管系统flexible riser 挠性隔水管Flexible storage carousel 挠性管存管盘flexible structure 挠性结构flexible subsea pipe 挠性水下管道Flexible technology 挠性技术floating production 浮式采油floating production platform 浮式采油平台floating production system 浮式采油系统Flow Line 出油管flow meter 流量计Flowbase 出油基座fluid barrier 流体隔层fluid characteristics 流体特性fluid compatibility 流体相容性fluid level 流体液位fluid samples 流体样本fluid temperature 流体温度FPS motion FPS运动Free Hanging 自由悬挂free standing 自由竖立Frequency Shift 频移friction coefficient 摩擦系数full bore annulus circulation 全井筒环空循环Functional requirements 功能要求fusion-bonded epoxy 热熔结环氧Gas compressor 气体压缩机gas export line 天然气输出线路gas export line 天然气输出线路gas lift 气举Gas lift line 气举管线Gas Metal Arc Welding 气体保护金属极电弧焊gas pipeline 天然气管道Gas pipeline system 天然气管道系统gas trunkline 天然气干线Gas Tungsten Arc Welding 钨极气体保护电弧焊general arrangement 总体布局general arrangement 总体布置general corrosion 全面腐蚀Gimbal 常平架Girth welds 管道环形焊缝Global Positioning System 全球定位系统gravel pack 砾石充填green canyon Green峡谷grit blasting 喷钢砂guide frame 导向架guide funnel 漏斗形导向承口guide pin 导向销guide pin 导向销guide pin 导向销guide post 导向柱guide sleeve 导向套guide wires 导向绳Guideline Drilling 导向绳钻井Guiding roller 导向滚轮hammer unions 锤击由任hand valve 手动阀Hazardous Area 危险区Heat Affected Zone 热影响区Heat soak tests 热浸试验Heat tracing 伴热heat tracing 伴热heat transfer 热传导heat transfer 热传导heat transfer 热传导heat treatment 热处理heating lines 加热管线heating system 加热系统heating technique 加热技术helical strake 螺旋箍条High Collapse Resistance 高抗挤毁（性）high collapse resistance hose 高抗挤毁（HCR）软管high cost 高成本High Density 高密度High Density Polyethylene 高密度聚乙烯high frequency alternative current 高频交流电流high lay tensions 高敷设张力high pressure 高压high pressure jets 高压喷射装置high procurement cost 高采购成本HIGH TEMPERATURE 高温high-density 高密度hollow glass micospheres 空心玻璃微球hollow glass microsphere 空心玻璃微球hoop strength layer 环向强度层horizontal 水平horizontal connection 水平连接Horizontal Connector 水平连接器horizontal plane 水平面horizontal position 水平位置Horizontal powered reel 水平动力卷轴horizontal reel 水平卷轴horizontal subsea Christmas tree 水平水下采油树horizontal subsea tree 水平水下采油树horizontal tree 水平采油树Horizontal Tree stinger 水平采油树插入管hose liner 软管内衬hose liner 软管内衬Host' platform “主”平台Hot fluid 热流体Hot rolling clad pipe 热轧复合管Hot rolling process 热轧工艺hot stab 热入扣hot-rolling mill 热轧机hot-stab 热入扣hybrid riser 复合隔水管hybrid riser system 复合隔水管系统hybrid riser tower 复合隔水管塔hybrid riser tower 复合隔水管塔hydrate formation 水合物形成hydrate formation temperature 水合物形成温度hydraulic 液压Hydraulic Analysis 液压分析hydraulic connection 液压连接部分hydraulic connectors 液压连接器Hydraulic coupler 液压接头Hydraulic Couplers 液压接头hydraulic couplings 液压接头hydraulic couplings 液压接头Hydraulic cylinder 液压缸Hydraulic Distribution 液压分配Hydraulic Distribution Module 液压分配模块hydraulic expansion method 液压膨胀法hydraulic fluid 液压油hydraulic fluid 液压液Hydraulic fluid cleanliness 液压液清洁度hydraulic flying leads 液压引线hydraulic function 液压功能hydraulic galleries 液压坑道Hydraulic Hoses 液压软管hydraulic interface 液压接口hydraulic jet pump 水力喷射泵hydraulic line 液压管线hydraulic line 液压管线Hydraulic lock 液压锁hydraulic motor 液压马达Hydraulic oil 液压油Hydraulic output 液压输出Hydraulic Power Unit 液压动力装置hydraulic press 液压机hydraulic pressure 水压hydraulic pressure 水压hydraulic supplies 液压供应hydraulic supply 液压供应Hydraulic Supply 液压供应Hydraulic System 液压系统Hydraulic tubes 液压管hydraulic umbilicals 液压脐带管hydrodynamic load 水动力载荷hydrogen embrittlement 氢脆变hydrogen embrittlement 氢脆变Hydrogen Induced Cracking 氢致开裂hydrostatic collapse 静水压挤毁hydrostatic pressure 静水压力I.D. punch 内径穿孔Indicator rod 指示杆Induction cable 感应电缆Induction current 感应电流induction heating 感应加热Induction Welded pipe 感应焊管Induction Welding 感应焊接In-house experience 内部经验In-house technical database 内部技术数据库injection fluids 注入流体injection line 注入管线injection of chemicals 化学剂注入injection point 注入点injection point 注入点injection point 注入点Injection Valves 注入阀injection well 注入井in-line oscillations 平行振动inner pipe 内管Insert choke 嵌入式油嘴installation 安装installation 设备（一般大型设备，注意文中是否有出现）installation method 安装方法installation methods / sequences 安装方法/安装顺序installation parameters 安装参数installation phase 安装阶段installation procedure 安装程序installation process 安装过程installation processes 安装过程installation technique 安装技术installation tolerances 安装公差Installation tolerances 安装公差Installation Vessel 安装船Installation vessels 安装船instrument unit 测量装置instruments 仪器insulating properties 绝热性质Insulation foam 隔热泡沫Insulation Foam 保温泡沫insulation layer 隔热层Insulation resistance 绝缘电阻Integral Valves 集成阀Integration Test 完整性试验interaction model 相互作用模型interface area 接口区interface flange 接口法兰INTERFACE REQUIREMENT 接口要求interface with Xmas tree flanges 与采油树法兰的接口interfaces 接口interfaces 接口internal carcass 内部架构internal corrosion 内部腐蚀internal diameter 内径internal pressure 内压Internal pressure containment 内压限制Internal Profile 内剖面Internal Profile Datum 内剖面基准internal sealing profile 内部密封剖面internal service pressure 内部工作压力internal temperature 内部温度internal tree cap 内部采油树帽Internal welding 内部焊接International Electrotechnical Commission 国际电工委员会Intervention 干预intervention 干预INTERVENTION PHILOSOPHY 干预原理Intervention System 干预系统intervention task 干预任务isolation test tool 绝缘试验工具isolation valve 隔离阀J lay ramp J型敷管滑道J Lay semi-submersible J型铺管半潜式平台J-Lay J型铺管J-Lay method J型铺管法junction 连接junction box 接线盒junction box 接线盒junction plate 连接板keel joint 龙骨接头Key issues 关键问题Kvaerner integrated service umbilical Kvaerner综合功能脐带管Kvaerner umbilical Kvaerner脐带管landing shoulder 坐放台肩landing string system 坐放式管柱系统large diameter 大直径large diameter 大直径Latch Mechanism 锁紧机构Latching mechanism 锁紧机构lateral loads 侧向荷载Lay ramp 敷管滑道laying parameters 铺管参数Lazy S 低弯度S型Lazy Wave 低弯度波形Lazy Wave 低弯度波形Lazy wave 低弯度波形Leading Tug 首拖船leak path 渗漏通道level indicator 液面指示器life cycle cost 寿命周期成本Life Cycle Costing 寿命周期成本Life Cycle Costing 寿命周期成本（LCC）Line Insulation Monitor 管道保温监控line pipe 输送管Linear pullin winch 直线式引入绞车Linear Variable Differential Transformers (LVDT) 线性差动变压器（LVDT）linear winch 直线状绞车liner material 内衬材料liner tube 衬管liner tube 衬管Load ring 承载环load transfer 载荷转移load transfer 载荷转移local buckling criteria 局部折皱标准local control 本地控制器local panel control 本地面板控制盘Lock ring 锁环locking mechanism 锁定机构long beam 长臂long term 长期longitudinal seam 纵向缝longitudinal seam welding 纵向缝焊接low-alloy carbon-steel 低合金碳钢Lower Marine Riser Package 下部海洋隔水管插件（LMRP）Lower tool joint 下部工具接头major component 主要组件major subsea components 主要海底组件male hub 公卡箍Man Machine Interface 人机接口management system 管理系统Management System 管理系统Mandrel 工作筒manipulator 机械手manipulator arm 操作手臂manipulator arm 机械手臂manipulator arms 机械手臂manipulators 机械手manipulators 机械手manual valves 手动阀manufacturer 制造商marginal field 边际油田Marine Drilling Riser 海洋钻井隔水管marine environment 海洋环境marine growth 海生物聚集marine riser 海洋隔水管Master Control Station 主控台mechanical properties 机械性能Mechanised Pulsed Gas Metal Arc Welding 机械脉冲气体保护金属极电弧焊Medium size flowline 中等尺寸出油管线Melting steel 熔融钢水messenger line 引缆metal to metal seals 金属对金属密封metal tube 金属管Metallic Materials 金属材料metallic sealing materials 金属密封材料Module Replacement Tool (MRT) 模块更换工具（MRT）monitoring system 监控系统Mono Bore Tree 单筒采油树moon pool 月池mooring line 系泊绳Mounting Base 安装基座Mudline Conversion System 泥线转换系统mudline suspension system 泥线悬挂系统Mudline Tree 泥线采油树Mudline Wellhead 泥线井口Multi Mode Running Tool (MMRT) 多模式下送工具（MMRT）multi-phase flow meters 多相流量计multiphase flows 多相流体Multiple load shoulder profile 多载荷台肩剖面National Aerospace Standard 国家宇航标准natural period 固有周期navigation system 导航系统neutrally buoyant 中和浮力normal operating 正常操作normal operation 正常操作North Sea 北海offshore hydrocarbon pipeline 海上油气管道offshore installation 海上安装Offshore Installations 海上设备offshore pipeline 海洋管道offshore production platform 海上生产平台offshore production platform piping system 海上生产平台管道系统Offshore Technology Conference 海洋技术会议Oil pipeline transportation systems 石油管道运输系统oil/gas production rate 油/气生产速度open-hearth steelmaking 平炉炼钢operating conditions 作业条件operating cost 运营成本operating cost 运营成本operating pressure 操作压力operating temperature 操作温度operation 作业operational temperatures 操作温度operator skill 操作者技能operators 操作者optical fibre 光纤optical fibres 光纤orbital welding 轨道焊接Orientation device 定向仪orientation system 定向系统O-Ring seals O环密封圈O-rings seals O环密封圈outboard hub 外侧轮毂outer pipe 外管outer sheath 外部护套outer sheath 外部护套outer sheath 外部护套outer surface 外表面outer thermoplastic sheath 热塑外部护套overall length 总长overall System 整个系统Overboard chute 船外下降溜槽overboarding chute 船外下降溜槽override functions 优先功能pack off retrieval tool 封隔收回工具Packoff 封隔Pack-Off 封隔Pack-Off Assembly 封隔总成paraffin deposits 结蜡parallelepipedic billets 立方坯板料parking position 停放位置partial pressure 分压performance verification 性能验证permanent guide base 永久导向基座Piercing of billets 坯板料穿孔Pig Detection 清管器检测Pig Detector 清管器检测器pig launcher 清管器发送筒pig receiver 清管器接收筒pilot valves 先导阀pin connection 销连接pin connector 销连接器PIPE DIAMETER 管道直径Pipe dimensions 管道尺寸Pipe expansion calculations 管道膨胀计算pipe in pipe system 管中管系统Pipe inside diameter 管道内径pipe joints 管接头pipe joints 管接头pipe layer dimensions 管层尺寸pipe material 管道材料pipe outside diameter 管道外径pipe section 管道截面Pipe storage Reel 存管卷筒pipe strings 管柱pipe structure 管道结构pipe structure 管道结构pipe system 管道系统pipe wall 管壁Pipe wall thickness 管道壁厚Pipe-in-pipe system 管中管系统pipelay vessel 铺管船pipeline 管道pipeline 管道Pipeline bundle system 管束系统pipeline burial 管道埋设pipeline design 管道设计Pipeline Design Method 管道设计方法Pipeline End Manifold 管道末端管汇Pipeline end manifold (PLEM) 管道末端管汇（PLEM）Pipeline end terminations 管道端部终端设备pipeline systems 管道系统Pipeline Valve 管道阀piping system 管道系统plastic deformation 塑性变形plastic deformation 塑性变形Poisson coefficient 泊松系数Polyurethane Foam 聚氨酯泡沫Polyvinylidene Fluoride 聚偏氟乙烯position indicators 位置指示器Position Reference System 定位参考系统positioning system 定位系统Positive mechanical lockdown mechanism 正向机械锁定机构post-weld heat treatment 焊后热处理power cable 电缆power cables 电源电缆power channel 电力通道power management 电源管理power source 电源power source 电源power supplies 电力供应Power Supply 电源power supply 电源Power Supply 电源Power System 动力系统pressure balance 压力平衡pressure balanced 压力平衡pressure drop 压降Pressure Drop 压降pressure drops 压降pressure gauges 压力表pressure integrity 压力完整性pressure monitoring 压力监测Pressure Sensor 压力传感器pressure test 压力测试Pressure Vessel 压力容器pressure-drop 压降primary pressure 原始压力Product Flow 产品流动product leaflets 产品说明书production and annulus master valve 生产和环空总阀production bore 生产井筒production casing 生产套管production control system 生产控制系统Production Deck 生产甲板production facilities 生产设施production flow rate 生产流量production flowline 生产出油管线production flowline 生产出油管线production flowline system 生产出油管线系统production fluids 生产流体production gathering 生产集输Production line 生产管线production lines 生产管线Production Master Valve 采油主阀production mode 生产模式production phase 生产阶段production platform 生产平台production rate 采油速度production rates 采油速度Production Riser 生产隔水管production riser 生产隔水管production riser 生产隔水管production risers 生产隔水管Production String 生产管柱Production System 生产系统production system 生产系统Production Template 采油基盘production tree 采油树production tubing 生产油管Project Management 项目管理Project Manager 项目经理project specification 项目规范propagation buckling 延伸折皱propagation pressure 延伸压力propulsion system 推进系统protection cap 保护帽protective structure 防护结构pull force 拉力pull in cable 牵引线缆Pull in winch 牵引绞车pull-in and connection tool 牵引和连接工具pull-in cable 牵引线缆pull-in head 拉入头pull-in operation 引入作业pull-in winch 牵引绞车pull-in/connection method 牵引/连接法Pump Down System 泵送系统pump systems 泵系统qualification 资质Qualification 资质qualification test 合格性测试Quality Assurance 质量保证quality control 质量控制Quality Plan 质量计划Quality System 质量体系Quenching 淬火Quick Connect 快速连接radial forces 径向力reaction loads 反作用载荷real time 实时Reel-Lay 卷管式铺管法Reference Book 参考手册reliability analysis 可靠性分析relief valves 安全阀removable guide posts 活动导向柱reservoir 油藏reservoir 油藏reservoir 油藏reservoir 油藏reservoir pressure 储集层压力residual axial tension 残余轴向拉力residual strains 残余应变resin binder 树脂粘合剂resistance factor 阻力系数Response time 响应时间Retrieval Tool 收回工具return line 回油管线return line 回油管线return lines 回油管线return tank 回油罐rigid line 刚性管道rigid pipe 刚性管道Rigid Pipe 刚性管rigid pipeline 刚性管道rigid production riser 刚性生产隔水管rigid reeled gas line 刚性卷筒式天然气管道rigid steel pipe 刚性钢管rigid steel riser 刚性钢质隔水管ring grooves 环形槽riser 隔水管riser base 隔水管基座riser connector 隔水管连接器riser joint 隔水管接头Riser joints 隔水管单根Riser Pressure 隔水管压力riser system 隔水管系统riser tension 隔水管张力riser tensioner 隔水管张紧器rolling process 轧制工艺rotary table 转盘ROV 水下机器人（ROV）ROV 水下机器人ROV 水下机器人ROV AND TOOLS 水下机器人和潜水工具ROV control cabin ROV控制舱ROV deck equipment ROV甲板设备ROV interface ROV接口ROV intervention ROV修井ROV locking interface ROV锁紧接口ROV manufacturers and subsea contractor ROV制造商和水下承包商ROV panels ROV面板ROV system ROV系统ROV vehicles ROV装置ROVs and Tools 水下机器人和潜水工具running sequence 送入顺序running tool 下入工具running tool 下入工具running tools 下入工具Safe Area 安全区safety factor 安全系数Safety Valve 安全阀safety valve control 安全阀控制Sand Detector 测砂器sand monitor 测砂器sand monitoring 防砂监控Sand Monitors 测砂器Satellite tree 卫星采油树satellite well 卫星井saturation diving 饱和潜水scan cycle time 扫描周期scan time 扫描时间sea bed 海床sea bed 海床sea bottom 海底sea bottom 海底sea level 海平面Sea level 海平面sea state 海况sea states 海况sea surface level 海面sea water 海水sea-bed 海底sea-bed level 海底水位seafloor wellhead 海底井口Seal area 密封区seal assembly 密封总成Seal Elements 密封元件SEAL Engineering SEAL工程seal material 密封材料Seal plate 密封板seal pocket 密封腔seal surfaces 密封表面Sealines 海下管线sealing system 密封系统seam welding process 管缝焊接工艺seamless pipe 无缝管seamless tube 无缝钢管sea-states 海况seawater tolerance 耐海水Seaway Condor Seaway Condor selector valve 选择阀semiconductor device 半导体装置sensing element 传感元件sensing pins 感应针sensor systems 传感器系统serial number 序列号service life 使用寿命service line 维修管线Service line 维修管线seven-function 七功能seven-function 七功能seven-function 七功能severe weather 恶劣天气shallow water 浅水shear pins 剪切销钉sheave package 滑轮组件side valve tree 旁阀采油树Signal Pair 信号线对signal transmission line 信号传输线silicate microspheres 硅酸盐微球体Single Bore Tree 单筒采油树Skin Effect Current Tracing 集肤电伴热sled piping 滑车管道sleeve pipe 套管soft soil 软土soil conditions 土壤条件solenoid valve 电磁阀Span calculations 跨度计算spare parts 备件special tools 专用工具specific project 指定项目Spirally-oriented seam welded pipe 螺旋焊缝管splash zone 飞溅区splash zones 飞溅区Split lock ring 开口锁环Spool Piece 短管Spool tree 四通采油树spooling 缠绕spooling system 缠卷系统spray cooling 喷淋冷却法stab plate 插板stainless steel 不锈钢stainless steel strips 不锈钢带static analysis method 静态分析法steel armoured pipe 钢质铠装管道steel catenary riser 钢质悬链线隔水管Steel Flying Lead 钢引线steel jacket pipe 钢质夹套管steel pipe 钢管steel riser 钢质隔水管steel tube umbilical 钢管脐带管steel tube umbilical 钢管脐带管steel tube umbilical 钢管脐带管Steelmaking process 炼钢工艺Steep S-Lay 陡S型铺管法Steep S-Lay vessel 陡S型铺管船Steep Wave 高弯度波形Steep Wave 高弯度波形Steep wave 高弯度波形Steep wave 高弯度波状Stepwise Cracking 阶式断裂storage reel 存储盘架storage reel 存储盘架straight line 直线strength members 强度元件Stress Corrosion Cracking 应力腐蚀开裂strong currents 强电流strong seawater currents 海水强流Submarine pipeline code 海底管道规范submarine pipeline system 海底管道系统Submerged Arc Weld 埋弧焊Submerged arc welded pipe 埋弧焊管submerged weight of the pipeline 管道浮重submerged weight of the soil 土壤浮重submerged-arc welded 埋弧焊submerged-arc welded seam 埋弧焊缝subsea blowout preventer 水下防喷器subsea christmas tree 水下采油树Subsea Christmas Tree System 水下采油树系统Subsea cluster manifold 水下丛式管汇Subsea cluster well system 水下丛式井系统subsea contractor 水下承包商Subsea Control Module 海底控制模块subsea control module mounting base 海底控制模块安装基座（SCMMB）Subsea Control Module Running Tool 海底控制模块下入工具Subsea Control Systems 水下控制系统subsea drilling system 水下钻井系统Subsea Electronics Module 水下电子装置模块subsea field 海底油气田subsea intervention tree 水下修井采油树subsea manifold 水下管汇Subsea Production Control System 海底生产控制系统SUBSEA PRODUCTION EQUIPMENT 海底采油设备Subsea Production Manifold 海底采油管汇Subsea Production System 海底生产系统Subsea Production Template 海底生产基盘subsea system 水下系统Subsea tree single-piece spool body construction 水下采油树单件四通本体结构Subsea wellhead 海底井口装置Subsurface Safety Valve 水下安全阀Suction Pile 吸力桩Suction Piles 吸力桩Sulphide Stress Corrosion Cracking 硫化物应力腐蚀开裂super duplex 超双相super-duplex 超双相Supply Tank 供应罐supply voltage 电源电压supply voltage 电源电压support frame 支撑框架surface area 表面积surface BOP 地面防喷器surface casing string 表层套管柱Surface Conductor 地面导管Surface Controlled Sub-Surface Safety Valve 地面控制水下安全阀surface production processing facilities 地面生产处理设施Surface Safety Valve 地面安全阀surface support vessel 水面供应船surface tree 地面采油树Surface Tree 地面采油树survey vessel 测量船swab valve 抽汲阀syntactic foam 复合泡沫syntactic foam 复合泡沫Tag Number 标号target area 目标区域temperature sensor 温度传感器Temporary Guidebase 临时导向基座tensile armours 抗拉铠装tensile strength 拉伸强度tension capacity 张力大小Tension Leg Platform 张力脚平台tension leg platforms 张力腿平台tension load 张力载荷tension loads 拉伸载荷terminal head 终端头termination 终端termination 终端termination point 终端点termination unit 终端装置test cap 测试帽Test Electrical Power Unit 试验电源装置test method 测试方法test pressures 测试压力Test Tool 试验工具Teta profile T形剖面Teta spiral T形螺旋层thermal expansion 热膨胀thermal expansion coefficient 热膨胀系数thermal insulation 隔热thermal insulation 隔热thermal insulation 隔热thermal insulation and Aluminium-sacrificial anode system 隔热和牺牲铝阳极系统thermal insulation material 隔热材料thermal insulation system 隔热系统thermal insulation system 隔热系统thermal shrink-fit method 热收缩-配合法Thermo-hydraulic fit method 热-液压配合法Thermo-Mechanical Controlled Processing 热机械控制工艺Thermoplastic friction sheath 热塑耐磨护层thermoplastic hose 热塑软管。

海洋工程专业英语词汇AA-60 fire door A-60级防火门a-hundred-year return period百年一遇abrasive (喷砂用的)磨料abrasive paper砂纸AC generator交流发电机AC motor交流电动机accelerated corrosion testing加速腐蚀试验acceptance criteria 合格准则access hole (for welding)=cope hole焊接工艺孔accommodation and power platform (APP) 生活动力平台according to =in accordance with =in line with =as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂adhere to 遵守(动词)adherence to 遵守(名词)adjacent columns 相临立柱adverse combination of loads荷载的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction) 建造批准Aforementioned 上述的aft winch 船艉绞车agitator 搅拌器air blower 鼓风机air compressor 空压机air drive pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验air-hose 风带aircraft obstruction beacon 航空障碍灯alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨酯漆allowable (working) stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮ambient air temperature 环境气温ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺栓anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂装表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method 超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anti-electrostatic floor 防静电地板anticorrosive paint 防锈漆antipollution measures 防污染措施API specified requirement API规定的要求apparent batter 视斜度applicable API specification API适用规范approach-departure sector 直升飞机起落扇形区appurtenance =attachment =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 绞接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态assemble 组装(动词)assembly 组装(名词)associated gas 伴生气at the option of A 按A的意愿atmospheric diving system=unpressurized diving system 常压潜水系统atmospheric vent 防空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统B(to be) buttered (焊接的)长肉back chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator(self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash purge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布氏硬度ball valve 球阀bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性barrel (管件的)加厚段base metal 母材, 基本金属basic design 基本设计basic electrode =lime type covered electrode 碱性焊条battery room 蓄电池间blowout preventer system (BOP system) 防喷器系统beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending moment 弯矩bending stress 弯曲应力bevel 坡口bevel angle 坡口面角度beveling/chamfering 开坡口bid drawing 招标图纸bilge /fire pump 舱底污水—消防两用泵bilge alarm system 污水报警系统bid/tender for 投标blast cleaning 喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow countn 打桩的锤击数blowdown vessel 排放罐blowhole; gas pore 气孔blowout preventer stack 防喷器组buoyant turret mooring 浮筒转塔式系泊boat landing 登船平台bolt, nut and washer 螺栓, 螺母及垫片bolted connection 螺栓连接boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joint 箱形节点brace 拉筋bracelet anode 手鐲式阳极branch member 支杆breathing apparatus, respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带bulb angle 球扁钢build-up girder 组合梁bulk head 隔板, 舱壁burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and management 经营管理butt-welded seam 对接焊缝butterfly valve 蝶阀Ccable layer 敷缆船cable rack tray 电缆托架caisson 沉箱caisson washing pump 洗舱泵caisson-type platform 沉箱式平台can (管件的)段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment =overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon dioxide (CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机carrier (搬运) 小车carry out =perform =conduct =execute 进行catenary anchor leg mooring (CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel (CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room (CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵centrifuger 离心机ceramic fibres 防火陶棉ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链chair with arm-rests 带扶手的半软椅chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击实验chart datum 海图基准面check randomly 抽检check valve 止回阀checkered plate 花纹板chemical composition 化学成分chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤chisel 风铲chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐clearance 间隙client 业主, 顾客close drain tank 闭式排放罐closed /open circuit 闭/开路closed drain pump 闭式排放泵closed drain tank 闭式排放罐clustered well heads 丛式井口CO2 cylinder unit CO2 气瓶组CO2 extinguisher CO2 灭火器coal tar epoxy paint 含焦油环氧涂料coaming 档水扁钢coating 涂装coating interval 涂漆间隔coefficient 系数cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工collapse ring 加强环板column 立柱combustible gas detector 可燃气体探测器come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊completion riser 完井立管complex joint 复杂节点compliance with 符合(名词)comply with 符合(动词)composite rockwool ceiling 复合岩棉天花板composite rockwool panel 复合岩棉板concentric reducer 同心大小头conceptual design 概念设计concrete platform 混凝土平台condensate drum 冷凝液罐condensing water 冷凝水conductor 隔水套管conductor guide 套管导向cone 大小口, 锥体conform to =stick to =adhere to 符合, 遵守connection 节点, 连接consumption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld 双面连续贴角焊continuous welding 连续焊contract 合同contraction stress 收缩应力contractor 承包商control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole (焊接)工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀片corrosion protection 防腐corrugated plate interceptor 斜板分离器couplant UT用的耦合剂coupling 连轴器, 管箍crack 裂纹crane barge, crane vessel 起重船crane support 吊机支撑crater 焊口crawler crane 履带吊车criteria (验收)标准cross angle 交叉角cross section 横截面crow bar 撬杠cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat exchanger 原油换热器crude loading/export pump 原油外输泵crude loading pump 原油装载泵crude oil drain tank 原油排放舱crude preheat exchanger 原油预热器crude suction strainer 原油吸入滤器crude transfer pump 原油输送泵cup support 垫墩curing time (油漆的)固化时间current capacity (阳极的)电流容量current density (阳极的)电流密度current direction 海流方向curvature radius 曲率半径customer (试比较purchaser需方)客户(签合同后, 客户变需方)cut by torch 以火焰切割cut off 割除, 割除物cutoff allowance 切割裕量cutting plan 排板图cutting sheet 单件图D(in) duplicate 一式两份(to) drive piles 打桩DAC curves 距离—振幅曲线daily diesel filter 日用柴油滤器damage-prone connection 易破坏的节点damper, dampener 减振器DC generator 直流发电机Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊机deck floor plate 甲板板deck water seal unit 甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defeat /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater 脱水预热器dehydrator feed pump 电脱水供给泵delivery of materials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design parameters 设计参数detail 详图detail design 详细设计develop /establish a document 编制文件dew point 露点DFT (dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve 隔膜阀die stamp 钢印diesel daily tank 柴油日用罐diesel filter coalescer 柴油过滤净化装置diesel generator set 柴油发电机组diesel oil daily tank with heater 柴油日用罐(带加热器)diesel pump 柴油泵diesel storage tank 柴油储罐diesel storage tank with heater 柴油储罐(带加热器)diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风器dihedral angle 二面角dimensional checks 尺寸检验direct /alternating currentarc welding 直/交流电弧焊direct current emergency supply 直流应急电源disassembling 拆除discontinuity 缺陷displacement oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel 潜水作业船document approval and issue 文件的批准和下发documentation 文件编制dog 组装用的刀把dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bed 双层床double bevel groove K形坡口double bollard 双柱带缆柱double groove 双面坡口double probe method 双探头法double V groove 双面V形坡口(X形坡口) double plate 垫板, 包板down hill welding 下向焊drain pit 排放池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类图纸种类有:conceptual drawing 概念图纸basic drawing 基本设计图bid drawing 招标图纸design drawing 详细设计图fabrication drawing 加工设计图shop drawing 车间加工图as-built drawing 完工图dredger 挖泥船drift pin 心轴, 销子drift test 管流试验, 管线试通drill 钻头drilling module 钻井模块drilling platform 钻井平台drilling template 钻井基盘drillship, drilling ship 浮式钻井船driving voltage 驱动电压dry chemical extinguisher 干粉灭火器dry-type tree 干式采油树dryer 烘箱during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynamic-positioning rig 动力定位钻井船Eearth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping (卷管的)压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electric-hydraulic valve 电—液操作阀electrical connection 导电连接electro-slag welding 电渣焊接electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把, 焊钳electrolyte 电解质elevation (EL) 标高, 立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system (ESD)应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱, 机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW (electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipment 防爆设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surface of brace 拉筋的外表面extra margin of stress 应力裕量Ffabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物(又临时吊点) fabrication design 加工设计fabrication phase 制造阶段fabrication sequence 顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组对, 现场组对field mating point 海上对接点(如导管架与组块对接点) field splice 现场拼接field weld 现场焊缝fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gas detecting system 火灾—可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer, fire proof door 防火门fire extinguishing system 消防系统fire fighting water, fire water 消防水fire foam hydrant 消防泡沫栓fire hose station, hose box 消防箱fire monitor 消防炮fire panel 火灾—可燃气报警显示盘fire proof wall, fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire water /foam monitor 消防炮(水或泡沫)fire water deluge system 大水量灭火系统fire water hose rock 消防水软管fire water hydrant 消防水栓fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire-fighting vessel, fire boat 消防船fireman box 消防员箱first aid kit 急救箱first coat 底漆first stage hydrocyclone 一级水力旋流器first stage separator 一级分离器fit-up 坡口组对fitter 组装工fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台fixed platform 固定式平台fixed tower SPM 塔系泊flame arrester 组火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 翼缘, 法兰flare assembly 火炬总成flare boom 火炬臂flow indicator (FI) 流量显示器flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat welding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose 浮式输油软管floating loading hose 浮式装油软管floating oil production andstorage unit (FPSO) 浮式生产储油装置floating oil storage unit 浮式储油装置floating production platform 浮式生产平台floating production, storageand off-loading tanker 浮式生产储油外输轮floating state 漂浮状态flooding 注水floppy disk 软盘flow chart 流程图frame structure 梁格结构flow quantity recorder (FQ) 累计流量计flow switch 流量开关flux 焊药flux cored arc welding (FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam monitor 泡沫泡foam station 泡沫站fog horn, fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置。

船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区building basin 船台 bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船 buoyancy 浮力buoyancy 浮力Bureau Veritas (法国)船级社burning machine 烧割机 butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例，按约定3、C类camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量，货舱容量，舱容cargo cubic 货舱舱容，载货容积cargo handling 货物装卸 cargo owner 货主carpenter 木匠 carriage of grain cargoes 谷类货物输运机cascading of waves upon…海浪跌落于… casualty 事故，死伤，灾难catamaran 双体船categorize 分类centroid 形心，重心，质心，矩心 chine 舭，舷，脊chock 木楔 circumscribe 外接，外切circumsection 外切Coast Guard cuttle(美国）海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船compartment 舱室 concave 凹，凹的，拱conceive 设想，想象concept design 概念设计configuration 构形，配置configuration安排，构型，配置conspicuous 显着的，值得注意的containerized 集装箱化 contract design 合同设计contract design 合同设计 contracted scale 缩尺core box 型芯 corrosion 锈蚀，腐蚀couple 力矩，力偶crest (of wave) 波峰crew quarters 船员居住舱 Critical Path Method (CPM) 关键路径法cross section 横剖面 cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element 重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫4、D类damage stability 破损稳性 damp out 阻息，逐渐降低dead load 恒(静)载荷 deadweight 总载重量(吨)deballast 卸除压载(压舱)deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿 deckhouse 舱面室，甲板室declivity 坡度，斜度 deep V hull 深V型船体deformation 变形 delivery 交船Department of Trade (英国)贸易部 deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深 design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离，偏差 devious 曲折的diagram 图，原理图，设计图，流程图 dimension 尺度，元，维displacement 排水量distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员 drag 阻力Drainage 排(泄)水draught(=draft) 吃水，草图，设计图，牵引力drawing office 绘图室 dredge 挖泥船drift 飘移，偏航drilling rig 钻架 dry dock 干船坞5、E类eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工 elevations 高度，高程，船型线图的侧面图、立视图，纵剖线图 enclosed fabrication shop 封闭式装配车间end on 端对准 endurance 续航力endurance 续航性 entrance 进流段 erection (船体)组装erection 装配，安装 expedient 权宜之计extrapolate 外插f. p. = forward perpendicular 艏柱fair 光顺 fair 光顺fastening 坚固件,紧固法fatigue 疲劳 feasibility study 可行性研究 fender 护舷ferry 渡轮，渡口，渡运航线ferry 轮渡(载运) fillet weld connection 贴角焊连接fine fast ship 纤细(细长)高速船 fine form 瘦长(细长)船形Flank 侧面, 侧翼, 侧攻flanking rudders 侧翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队 flexural 挠曲的float 浮动时间 floating drydock 浮船坞 flood 进水，泛滥floodable length curve 可浸长度曲线 flow pattern 流型，流线谱flow of materials 物流 flush 平贴，磨光forging 锻件，锻造 form coefficient 船形系数forming operation 成型加工 forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩 foundry casting 翻砂铸造 foundryman 铸造翻砂工 frame 船肋骨，框架，桁架frame 框架 freeboard 干舷freeboard 干舷freeboard 干舷freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社 girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船) ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入 immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination 小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布)iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。

一词汇(be)subject to…经受…(in) duplicate 一分两式(to be) buttered (焊接的)长肉(to) drive piles 打桩4:1 taperd transition bevel 四比一过渡坡口A resulting formB 由B导致AA-60 fire door A-60级防火门abrasive （喷砂用的）磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流发动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则access hole(for welding) =cope hole （焊接）工艺孔accommodation and power platform(APP) 生活动力平台according to=in accordance with=in line with =as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂adhere to 遵守（动词）adherence to 遵守（名词）adjacent columns 相邻立柱adverse combination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system航空无线电AFC(approved for construction) 建造批准aforementioned 上述的aft winch 船艉绞车agitator 搅拌器a-hundred-year return period 百年一遇air blower 鼓风机air compressor 空压机air driven pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethanel 脂肪族聚氨脂漆allowable(working)stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮ambient air temperature 环境气度ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺拴anchor ground 锚地anchor pile 锚桩anchor profile/pattern 涂桩表面的粗糙度anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anticorrosive paint 防锈漆anti-electrostatic floor 防静电地板antipollution measures 防污染措施API specified requirements API规定的要求apparent batter 视斜度applicable API specification API适用范围approach-departure sector 直升飞机起落扇行区appurtenance =attachment =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 铰接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-built drawing 完工图as-rolled 轧制状态assemble 组装(动词)assembly 组装(名词)associated gas 伴生气at the option of A 按A的意愿Atmospheric diving system =unpressurized diving system 常压潜水系统atmospheric vent 放空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统back chipping 清根back gouging 反面气刨backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash surge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布式硬度ball valve 球阀bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性barrel (管件的)加厚段base metal 母材、基本金属basic design 基本设计basic drawing 基本设计图basic electrode =lime type covered electrode 碱性焊条battery room 蓄电池间beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前bending moment 弯矩bending stress 弯曲应力bevel 坡口bevel angle 坡口面角度beveling/chamfering 开坡口bid / tender for …投标bid ddrawing 招标图纸bid drawing 招标图纸bilge / fire pump 舱底污水-消防两用泵bilge alarm system污水报警系统blast cleaning喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数blow out preventer system(BOP system) 防喷器系统blowdown vessel 排放罐blowhole;gas pore 气空blowout preventer stack 防喷器组boat landing 登船平台bolt,nut and washer 螺栓、螺母及垫片bolted connection 螺栓连接boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船boundary condition 边界条件bow 船艏box beam 箱形梁box type joinnt 箱形节点brace 拉筋bracelet anode 手镯式阳极branch member 支杆breathing apparatus , respirator 防毒面具bridge 栈桥bridge (overhead) crane 天车吊brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带build-up girder 组合梁bulb angle 球扁钢bulk head 隔板，舱壁buoyant turret mooring 浮筒转塔式系泊burn through 烧穿burner 气焊工burr and flashing 飞边毛刺business and management 经营管理butterfly valve 蝶阀butt-welded seam 对接焊缝cable layer 敷缆船cable rack / tray 电缆托架caisson 沉箱caisson washing pump 洗船泵caisson-type platform 沉箱式平台can （管件的）段cantilever beam 悬臂梁cantilever jack-up rig 悬臂自升式钻井船cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment = overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机carrier （搬运）小车carry out = perform = conduct =execute 进行、执行catenary anchor leg mooring(CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel(CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room(CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链chair with arm-rests 带扶手的半软椅chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击试验chart datum 海图基准面chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤chisel 风铲chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐coefficient 系数cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板column 立柱combustible gs detector 可燃气体探测器come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊completion riser 完井立管complex with 符合（名词）comply with 符合（动词）composite rockwool ceiling复合岩棉天花板composite rockwool panel复合岩棉板concentric reducer同心大小头conceptual design 概念设计cone 大小口、锥体conform to = stick to = adhere to符合、遵守connection 节点、连接consumption rate 阳极消耗率continuous beam 连续梁continuous double fillet weld双面连续贴角焊continuous weldings连续焊contract合同contraction stress收缩应力contractor 承包商contractor（合同供方）control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole （焊接）工艺孔corrective and preventive action 纠正和预防措施correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐corrugated plate interceptor 斜板分离器couplant UT用的耦合剂coupling 连轴器、管箍crack 裂纹crane barge,crane vessel起重机crane support吊机支撑crater 焊口crawler crane履带吊车criteria（验收）标准cross angle 交叉角cross section横截面crow bar撬杆cruciform bollard 单十字带缆柱crude cooler 原油冷却器cup support 垫墩curing time （油漆的）固化时间current capacity （阳极的）电流容量current density（阳极的）电流密度current direction 海流方向curvature radius 曲率半径customer (比较purchaser) 客户（签合同后，客户变需方）cut by torch 以火焰切割cut off 割除、割除物cutoff allowance 切割裕量cutting plan 排版图cutting sheet单件图DAC curves 距离-振幅曲线daily diesel filter日用柴油滤器damage_prone connection 易破坏的节点damper , dampener 减振器DC generator 直流发电机ddry chemical extinguisher 干粉式灭火器Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊车deck floor plate 甲板板deck water seal unit甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater脱水预热器dehydrator feed pump电脱水供给泵delivery of materials 材料交货derrick barge 回转式起重船desander 除砂罐design basis 设计基准design drawing详细设计图design parameters 设计参数detail 详图detail design详细设计develop /establish a document编制文件dew point露点DFT(dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表diaphragm 隔板diaphragm valve隔膜阀die stamp 钢印diesel filter coalescer 柴油过滤净化装置diesel generator set柴油发动机diesel oil daily tank with heater 柴油日用罐（带加热器）diesel pump 柴油泵diesel storage tank with heater 柴油储罐（带加热器）diesel storage tank 柴油储罐diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀diffuser 布风器dihedral angle 二面角dimensional checks 尺寸校验direct /alternating current arc welding 直/交流电弧焊direct current emergency supply直流应急电源disassembling拆除discontinuity缺陷displacement oil tank 置换油罐distortion from welding 焊接变形distress signals 遇险呼救信号diver 潜水员diver support vessel潜水作业船document approval and issue 文件的批准和下发documentation文件编制dog 组装用的刀把dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bevel groove K形坡口double bollard 双柱带缆柱double groove 双面坡口double plate 垫板、包板double probe method 双探头法doulbe bed 双层床doulbe V groove 双面V形坡口（X形坡口）down hill welding 下向焊drain pit 排水池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通drill 钻头drilling module 钻井模块drilling platform 钻井平台drilling template 钻井基盘drillship ,drilling ship 浮式钻井船driving voltage 驱动电压dryer 烘箱dry-type tree 干式采油树during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection 着色检验dynamic-positioning rig 动力定位钻井船earth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping （卷管的）压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electrical connection 导电连接electric-hydraulic valve 电-液操作阀electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把、焊钳electrolyte 电解质electro-slag welding 电渣焊接elevation(EL) 标高、立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system(ESD) 应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱、机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW(electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipment 防暴设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surfaceof brace 拉筋的外表面extra margin of stress 应力裕量fabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物（如临时吊点）fabrication design 加工设计fabrication drawing 加工设计图fabrication phase 制造阶段fabrication sequence 制造顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组队、现场组对field mating point 海上对接点（如导管架与组块对接点）field splice 现场拼接field weld 现场焊缝fiexed platform 固定式平台fiexed tower SPM 塔系泊fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆first coat 底漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gs detecting system 火灾-可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer,fire proof door 防火门fire extinguishing system 消防系统fire fighting water, fire water 消防水fire foam hadrant 消防泡沫拴fire hose station ,hose box 消防箱fire monitor 消防炮fire panel 火灾-可燃气报警显示盘fire proof wall ,fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire waater hose rock 消防水软管fire water deluge system 大水量灭火系统fire water hydrant 消防水拴fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire water/foam monitor 消防炮（水或泡沫）fire-fighting vessel ,fire boat 消防船fireman box 消防员箱first aid kit 急救箱first stage hydrocyclone 一级水力旋转器first stage separator 一级分离器fitter 组装工fit-up 坡口组对fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台flame arrester 阻火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 冀缘、法兰flare assembly 火炬总成flare boom 火炬臂flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat position / downhand welding 平焊flat wekding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose浮式输油软管floating loading hose浮式装油软管floating oil production and storage unit(FPSU)浮式生产储油装置floating oil storage unit 浮式储油装置floating production ,storage and off-loading tanker 浮式生产储油外输轮floating production platform 浮式生产平台floating state 漂浮状态flooding 注水floppy disk 软盘flow chart 流程图flow indicator(FI) 流量显示器flow quantity recorder(FQ) 累计流量计flow swith 流量开关flux 焊药flux cored arc welding(FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam monitor 泡沫炮foam station 泡沫站fog horn ,fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼foreman 领班forged steel(FS) 锻钢fork lift 铲车，叉车forming 压制成型forming of plates into tubular 由板卷成管formula /equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性frame structure 梁格结构free water knockout vessel 流离水分离器fresh water pressure vessel 淡水压力罐fresh water pump 淡水泵fresh water tank pump 淡水罐fresh water tank with electric heater 淡水罐（带加热器）friction coefficient 摩擦系数fuel gas compressor packge 燃气压缩机撬fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatment package燃料气处理撬fuel oil drain tank燃料油排放罐fuel pump 燃油泵full coupling 全螺纹的接头full penetration weld 全溶透焊缝funnel-shaped guide喇叭口状导向furnace熔炉、加热炉fusible plug 异熔塞fusion/bond line 熔合线gantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting machine with magnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas injection module 注气组块gas metal arc welding 熔化极气体保护焊gas metal arc welding (GMAW) 熔化极气体保护焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊（含氩弧焊）gas turbine generator set 燃汽轮机发电机组gas turbine power generator 燃汽轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平绗材和垂直绗材girth weld 环缝global positioning system (GPS) 全球定位系统globe valve (normally clsoed) 截止阀（常闭）glycerin 甘油gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity damper 重力风闸gravity platform 重力式平台gravity type foundation 重力式基础grease 黄油、润滑油grind 打磨grinder 砂轮机grinding 打磨（名词）grinding machine 砂轮机grit 石英砂grit blasting 喷丸除锈groove 熔池groove angle 坡口角ground flush 磨平gs export facility天然气外输设备guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构gusset 节点板、筋板guyed tower platform拉索塔平台half nipple 一端带螺纹的接头halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon cylinder local panel 卤化烃就地控制盘halogenated hydrocarbon fire extinguishing system 卤化烃灭火系统hammer 锤子hand operated pump 手动泵hand winch 手动缆绳车handrail 栏杆hard hat 安全帽hardener 固化剂hauling to the front 牵引至码头前沿hazardous area 危险区heat affected zones(HAZ) 热影响区heat detector 热探测器heat exchanger 热交换气heat medium drain tank 热介质排放罐heat number 炉号heat traced pipeline 伴热管线heat treater 加热热处理器heat treatment 热处理heater 加热器heater treater 热处理器heater treater feed pump 热处理器供热泵heating medium boiler package 热介质锅炉撬heating medium circulating package 热介质循环撬heating medium collection tank 热介质收集罐heating medium diesel daily tank 热介质从柴油日用罐heating medium drain pump 热介质排放泵heating medium drain tank 热介质排放罐heating medium expansion vessel 热介质膨胀罐heating medium make-up pump 热介质再启动泵heating medium oil , thermal oil 传热介质油heating medium storage tank 传热介质油储存罐heating,ventilation and air conditioning system(HAV) 采暖、通风、空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板high pressure separator(HP separator) 高压分离器high strength steel 高强度钢high-low 错皮histogram （统计用）直方图hold 待定hold point （检验的）停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal position welding 横焊horizontal welding横焊hose 软管hose assembly 软管总成hose connection 软管接头hose handling crane软管起升吊机hose reel 软管轮hot dip galvanizing热浸锌hot water pressure vessel with electric heater 热水压力罐（带加热器）hot work 明火作业H-shape H型钢human life and property 人民生命财产hydrant 消火栓hydraulic pile_driving hammer 液压打桩锤impact resistance 耐冲击性impressed-current protection system 外加电流保护系统in accordance with 按照in any jacket plane 在任意导管架平面内in line with 按照in the light of 按照inclined stair 斜梯include but not limited to 包括但不限于included /groove angle 坡口角度inclusion 夹杂物incomplete fusion 未熔合incomplete penetration 未焊透inflatable liferaft气胀式救生筏inlet gas generator package 惰性气体发生器撬inorganic Zine primer 无机锌底漆in-process inspection 工序间的检验inside diameter(ID) 内径instrument master control room 仪表总控制室insulating flange 绝缘法兰insulation 保温insulation(heat traced) 保温加伴热intact / damage stability interference 完整/破损稳性（杆件之间的）相碰，打架intergranular corrosion 晶间腐蚀intermediate strength steel 中强度钢intermittent welding 断续焊internal and external beveling 内外坡口internal diameter 内径internal quality audits 内部质量审核internal stress 内应力interpass temperature 层间温度intersected pipe 被交管intersection line 相贯线invitation for bid =call for bid 招标jack 千斤顶jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending 导管架下水及竖立jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge 吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket modification 导管架改造jacking state 升降状态jacking system 升降系统jack-up rig 自压式钻井船jockey pump 供消防水干管的补给水泵joint can 节点加厚joint detail 节点详图J-tube J形管junction box(explosion proof) 接线箱（防暴型）key plan 总图、索引图killed steel 镇静钢kingpost 将军柱lack of fusion 未融合lack of penetration 未焊透launch way and rocker 滑道和摇臂launching and uprighting of a jacket 导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead sections and subsequent add-ons of piles 首桩及后续桩段leak test 密封性试验（试漏）leg 桩腿、导管leg of a fillet weld （角焊缝）焊角高度level 水平仪level gauge (with drain) 液位仪（带排放）life boat 救生艇life boat davit ,davit 吊艇架life buoy 救生圈life jacket 救生衣light type combustible gas detector 轻质可燃气体探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier ,LNG tanker 液化天然气运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deformation 局部变形local stress 局部应力longitudinal seam / weld 纵焊缝low explosion limit(LEL) 爆炸下限low heat input 底热量输入low hydrogen type electrode 底氢型焊条low pressure scrubber 底压气净化器low stress round nosed die stamp 底应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐（带加热器）main generator set 主发电机组main process line 主要工艺管线main switch room 主变电间main transformer room 主变压器室make-up drawing 造管图manhole 人孔manifold 管汇manned platform 驻人平台manual / hand welding 手工焊manufacture's instruction 产品使用说明marine growth 海生物marine radio system 海事通讯系统material substitution 材料代用material take off 材料估算单material traceability 材料跟踪maximun iperating water depth 最大工作水深may 可以（任意性的）mean sea level(MSL) 平均海平面mechanical property 机械性能mechanical test 机械性能试验medium pressure separator (MP separator) 中压分离器member 杆件member drawing （杆件的）单件图member number 杆件号metacenter 稳心metal lash 钢板网mezzanine deck 夹层甲板，半甲middle deck 中甲板mild steel 底碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous items 附件mismatch = high-low 错皮mobile drilling platform / rig 移动式钻井平台mobile radio system 移动式无线电系统model test 模型试验module 组块mold 模具mold lofting 放样moment 力矩moment of inertia 惯性矩moment of longitudinal inclination 纵倾力矩moment of transverse inclination 横倾力矩mooring bit 系缆柱mooring cable 系泊缆绳mooring dolphin 系缆柱mooring head 系泊头mooring template 系泊基盘mooring yoke 系泊刚臂motor operated valve 电动阀needle valve 针阀nipple对丝node can接点段nominal diameter公称直径non-combustible不可燃物质non-conformance不一致事项nondestructive examination(NDE) 无损检验nondestructive testing 无损检验nonskid ceramic mosaic 外观检验normal practice 通常作法normalize 正火normally open /close valve 常开／常闭阀notch toughness 缺口韧性NRL(naval research laboratory) drop weight test NRL落锤试验nut 螺母obsolete document 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设备offshore drilling rig 海上钻井装置offshore hook-up 海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration （污水）含油浓度oil depot 油库oil fence reel 围油栅卷筒oil moisture content 油雾含量onshore fabrication 陆上预制open drain pump 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐（带加热器）open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计original 原稿out of roundness 椭圆度outside diameter(OD) 外径ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊overboard 舷外overhanging beam 悬臂梁overhead position welding 仰脸焊overhead welding 仰脸焊overlap 焊瘤packer 封隔器padeye 吊点paint brush 油刷子paint roller 油漆滚子painter 油漆工panel assembling 平面组对，单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique 渗透检验polyurethane paint 聚氨酯涂料porosity 密集气孔port 左舷port hole 舷窗portable extinguisher 手提式灭火器portable two-way radio 双向无线电话positioner 定位器positioning 定位positive displacement flow meter 容积式流量计positive flow meter 正位流量计postweld heat treatment 焊后热处理pot life （油漆的）混合期限power wire bruch 电动钢丝刷preheat temperature 预热温度preheater 预热器pressure differential flow meter 差压流量计pressure gauge 压力表pressure regulation valve 压力调节阀pressure regulator(external tap) 压力调节阀（阀外引压）pressure relief valve 压力释放阀pressure safety valve 压力安全阀pressure vessels 压力容器primary structrural member 主结构杆probe 探头procedure qualification record(PQR) 焊接工艺评定process 工序process drain 工艺排放process module 工艺模块product identification and traceability 产品标识和跟踪production manifold 生产管汇production platform 生产平台production process and equipment 生产工艺及设备production shutdown panel(PSDP) 应急系统关断盘production welding 生产性焊接professional skill 专业技能protractor 量角器provision 条款，规定，措施punch marks 冲眼punching shear 冲剪应力purchase 采购purchase order number 订货合同号purge / pilot gas package 吹扫/引燃器撬块quality assurance 质量保证quality audit 质量审核quality awareness 质量意识quality check in process 工作中自检quality control(QC) 质量控制quality evaluation 质量评估quality loop 质量环quality manual 质量手册quality objectives 质量目标quality plan 质量计划quality planing 质量策划quality policy 质量方针quality related costs 质量成本quality review/assessment 质量评审quality surveillance 质量监督quality system 质量体系quasi-static loading 准静力荷载quay 码头quenched and tempered steel 淬火加回火钢quick coupling 快接管箍quick release hook(QRH) 快速解脱钩quiver 焊条筒radial offset of abutting edges of longitudinal weld seam 纵缝对接口的经向错皮radio equipment 无线电设备radio positioning system 无线电定位系统radiographic examination 射线检验radiographic interpretion 射线探伤的评片radiographic technique 射线探伤radiographic technique (RT) 射线探伤radius of operation 作业半经receipt and storage of materials receipt to /dispatch form a warechhouse 材料的接受和储存入/出库receiving inspection 到货检验reciprocating pump 往复泵recommended practice 推荐作法recovered oil tank 回收油罐red lead 红丹reducer 大小头，变经头reducer concentric 同心大小头reducer eccentric 偏心大小头refinery /petrochemical works 炼油/石化厂reinforcement 加强筋rejected or scrapped 拒收或报废relative humidity 相对湿度relaxation of rejection criteria 拒收标准的放宽release=issue =distribution （文件的）发放removable hatch 活动舱盖removable spool piece 可拆短管remove rate 返修率remove rust 除锈repair welding 补焊，返修焊缝rescue boat 救助艇residual stress 残余应力retention of documents 文件的保管review point 审核点revolving derrick barge 全回转式起重船rework 返工rib plate 肋板rigger 组装工人rigger 起重工right angle squaure 直角尺righting moment 回复力矩rimmed steel 沸腾钢ring stiffener 补强用环板riser clamps 立管卡子riser template 立管基盘riveter 铆工rock wool penel 岩棉板rock wool shell （保温用的）岩棉管rockwell hardness 洛氏硬度rod bar 圆钢rod electrode 电焊条rod stub 焊条头rolled shape / section 轧制型钢rolled steel plate 轧制钢板rolled tubular 卷制管roller bearing 滚珠轴承rolling direction （钢板的）轧制方向roll-up support 翻身垫墩root face 坡口的钝边root gap /opening 焊根间隙root run 根部焊道rope reel 缆绳卷筒rotary oil burner 旋转燃烧器rotary pump 旋转泵routine installation 一般性安装ROV(remote operated vehicle) 水下机器人row -up 立片，单片起立rubber gasket 像皮垫run -off tab 熄弧板run-on tab 引弧板sacrificial anode 牺牲阳极sacrificial anode 牺牲阳极saddle 垫墩saddle end 马鞍口safe working load (SWL) 安全工作荷载safety cap 安全帽safety factor 安全系数safety valve 安全阀safety zone 安全区sag 下垂salt spray test 盐水噴雾腐蚀试验salvage vessel 救援船sand blasting 喷砂除锈sand filter unit 砂滤装置sand hopper 喷砂砂罐sand jack 砂墩sandpaper 砂纸satellite navigation system 卫星导航系统satellite platform 卫星平台saturation diving 饱和潜水scaffolding 脚手架scanning speed 扫查速度screw driver 螺丝刀，改锥scriber 划线针s-curve （统计用）S曲线sea chest 海水柜sea current 海流sea state 海况sea water life pump 海水提升泵seafastening /tie down of jeckets （导管架装船的）固定seafloor bearing capacity 海床承载力seal weld 密封焊道seal welding 密封焊seamless pipe 无缝管seawater lift pump 海水提升泵second coating 二遍漆second gas scrubber 二级气体洗涤器second stage hydrocyclone 二级水力旋流器secondary /primary brace 次要/主要拉筋section 剖面图，一段segment 一段self shielded welding 自保护焊self tapping screw 自攻螺丝self weight 自重self-contained pressure regulator 自给式压力调节阀self-elevating drilling platform 自升式钻井船self-inspection 自检semi-automatic welding 半自动焊semifinshed/intermediate product 半成品semisub drilling unit 半潜式钻井装置semisubmersible rig 半潜式钻井船separator/urge vessel 分离/缓冲器serrated 锯齿形service after sales 售后服务sewage treatment unit 生活污水处理装置sewage unit 排污罐shall 必须（强制性的）shape cutting 仿形切隔shape steel 型钢shear stress 剪切应力sheet pile 钢板桩sheet piling 板桩shelf life 油漆的储存期限shielded metal arc welding (SMAW) 手工电弧焊shielded metal arc welding (SMAW）手工电弧焊shim plate 间隙条，导向块shop design 加工设计shop drawing 车间加工图shop drawing 车间加工图shop primer 车间底漆shot blast 噴丸除锈should 应该、最好、宜（建议性的）shower bath 淋浴器shrinkage strains 收缩应变shutdown switch 关断开关shutdown valve 关断阀shuttle tanker 穿梭油轮side bend test 侧弯试验silencer 消音器silver/silver Chloride(Ag/Ag Cl) reference cell 银/氯化银参比电池simple beam 简支梁simple joint 简单节点simply supported beam 简支梁single anchor leg mooring (SALM) 单锚腿系泊single berth with chest and drawers 有柜和抽屉的单人床single buoy mooring (SBM) 单点系泊single groove 单面坡口single point mooring (SPM) 单点系泊single V groove 单面V形坡口site assembly 空间组装，现场组装site installed 现场安装site representative 驻厂代表sit-on bottom stability 坐底稳性sitting on the sea bed 坐底skidded loadout 滑道式装船skip weld 跳焊skirt pile 裙桩skirt plate 裙板skirt sleeve 裙装套筒slag 溶渣slag catcher 捕集器slag inclusion 夹渣slag removal 清渣slate pencil 石笔slide door 滑动门slide down the launch way 沿滑道滑动slide shoe=lunch cradle 滑靴sling 吊索slip way 滑轨slop tank 污油罐slope 坡度slot welding 槽焊slotted member 开槽杆件。

海洋工程词汇（二）[TE-]Thermo/Couple(2) |热电偶Panel|屏Control Panel|控制盘Crude Oil|原油Chemical Injection 化学注入12-Port Dual-Speed Hub12 口双速集线器Explosion-Proof Speaker 防暴扬声器 1-Person RM 一人间 1-Person Room|1 人间 1st After Cooler 一级后冷却器 Fuel Gas Compressor 燃气压缩机 Gas Compressor 天然气压缩机 Gas Scrubber 天然气洗涤器 1st Level1st Level Separator 分离器 1st Stage Hydrocyclone 一级水利旋流器 1st Stage Separator 一级分离器 1st Stage Suction Scrubber 一级入口缓冲器 1st Warm Gas/Gas Exchanger 一级燃气热交换器 I-Beam TrackI 型梁轨迹 2 DA Bus Motor Space Heater 马达空间加热器 Floodlight (High Intensity Dischange)| 照明灯 2:Reserve 30 KVA2:Reserve 30 KVA Person Life Raft 救生筏 201(4-Man Room)4 人间 220V Small Power Distribution Panel For Living Quarter 220V 小功率配电盘（生活模块） 2nd After Cooler 二级后冷器 2nd Gas Compressor 二级天然气压缩机 2nd Gas Scrubber 二级天然气洗涤器 2nd Separator 二级分离器 2nd Separator Heaters 二级分离器加热器 2nd Stage Hydrocyclone 水力旋流器2nd Stage Separator 二级分离器 2nd Stg S Scrub 二级入口缓冲器 2nd Warm Gas/Gas Exchanger 二级热交换器 2P Chemical Injection Skid 化学注入撬 2-Position, 2-Way Solenoid Valve 两位两通电磁阀 2-Position, 2-Way Valve 两位两通阀 2-Position, 3-Way Solenoid Valve 两相三通电磁阀 3 DA Bus Motor Space Heater 马达空间加热器3Floodlight(High Intensity Dischange) Closing Life Boat(Fire Protect)封闭救生艇（火灾保护） Life /Pescue Boat 救生艇 4/2 Directional Control Valve 4 通/2 通控制阀 400V Emergency Switch gear/MCC 400v 应急配电盘和马达控制中心 400V Feeder Panel|400v 供电盘 400V Switchgear/MCC 400v 配电盘和马达控制中心 4-Way Solenoid Valve 四通电磁阀 500W ISB Transmitter 500w 多边带变送器 Lube Oil Storage Tank 润滑油储罐 Tank 罐 Explosion-Proof Speaker 防爆扬声器 Speaker 扬声器 High Pressure Wellhead ProductionHigh Pressure Wellhead Production 72 Lines Automatic Branch Exchange72 路/门自动交换分机 800W SSB Transmitter Emergency800w 应急单边带变送器A Zone Switch Room A 区控制开关间 A.P.TA.P.T Well 井 Water Injection Well|注水井 Submersible Well|潜水井 Abandon Platform Station|弃平台控制站 AC Contactor|交流接触器 AC Motor |交流马达 AC Motor Driver Mix|交流马达驱动搅拌器 AC Starting Motor|交流启动马达 AC Transformer Box|交流变压器箱 AC UPS Unit With Battery|带电池的交流 UPS 装置 ACB|空气断路器 ACB/MVB Panel|空气断路器/多频振荡器盘 Acc. Blocks|Acc. Blocks Access Cover|舱口盖 Accommodation Ladder Winch|舷梯绞车 Accu1 CCR AC Unit|中控室交流单元 Accu2 MSB Room AC Unit Accu2 MSB Room AC Unit Accumulator|累加器、蓄电池 Accumulator|蓄电池 Accumulator Cabinet|蓄电池箱Accumulator|储能器Acknowledge|Acknowledge Actuator BRC|Actuator BRC AFFF Tank|AFFF Tank Afffsolution Storage Tank|存储罐 Aftercooler|后冷却器 Aftercooler Assembly|后冷却器总成Aftercooler Housing|后冷却器壳Afterfilter|后过滤器Aft-Filt. / Hi Diff. Press.|高差压后过滤器 Agitator|搅拌器 Ail/Oil Cooler|油气冷却器 Ail/Oil Separator|油气分离器 Air After Cooler|空气后冷却器 Air After filter|空气后过滤器 Air Assist Filter|空气辅助滤器 Air Blower|鼓风机 Air Breaker|空气断路器 Air Breather Filter (H14)|过滤器呼吸器 Air Cases|Air Cases Air Circuit Breaker|空气断路器Air Cleaner Different Pressure Indicator| 空气过滤差压指示器 Air Compressor|空压机 Air Compressor Control Panel|空压机控制盘 Air Compressor Drive|空气压缩机驱动器 Air Compressor Instrument Skid|空压机仪表撬 Air Compressor LCP|空压机就地控制盘 Air Compressor Module|空压机模块 Air Compressor Package|空压机撬 Air Compressor RM.|空压机房 Suction Filter|入口过滤器 Air Condition Room|空调室 Air Conditioner|空调 CCR|中央控制室 E.S.R.|E.S.R. EMER Switch RM|应急开关间 Main Switch RM.|主开关间 MCC RM.|马达控制中心 Rest RM.|休息室 Sub.Pump Con.Rm.|电潜泵控制室 Air Conditioning Sea Water Pump Of Floor|空调海水冷却泵 Air Cooler|空气冷却器 Air Cylinder|空气瓶 Air Damper|调节风闸 Air Dryer|空气干燥器 Air Dryer Package|空气干燥器撬 Air Fan Cooler|空气冷却器 Air Filter|空气过滤器 Air Flow Control Damper|气流控制风闸 Air Foam Chamber|泡沫间 Air Foam Unit Skid|泡沫撬 Air Handling Unit|气动装置 Air Heater Filter|气体加热过滤器 Silencer|消音器 Air Inlet Filter|进气滤器 Air Inlet Silencer|进气消音器 Air Intake Filter|进气滤器 Air Middle Filter|空气中间过滤器Air Motor|气动马达Air Operated Regulating Valve|气动调节阀Air Pressure Regulator|空气压力调节器 Air Pressure Switch|空气压力开关 Air Receiver|空气瓶Air Reservoirs|空气存储器/空气瓶 Air Reservoirs For Accom. Ladder Winch|舷梯绞车的空气瓶 Air Separator|气体分离器 Air Shutoff Relay|空气关断继电器 Air Switch|气动开关 Air System|空气系统 Air Temperature Indicator|空气温度指示器 Air Ventilation|通风Air/gas Separator|空气/燃气分离器Air-Conditioner|空调机Air-Conditioner Panel|空调控制盘 Aircraft Warning Light Control Cabinet| 直升机报警信号灯控制柜 Aircraft Warning Light With Battery|带电池的直升机信号灯Air-heating Unit|加热器单元 Alarm Bell|警铃 Alarm Control Panel|报警控制盘 Alarm Horn|报警笛 Alarm Light|报警灯 Alarm Siren/Release Indicator Light|警报/解除指示灯Alarm Siren/Release Push Button|警报/ 解除按钮Alarm System|报警系统Alternator|交流发电机Amber Rotation Lamp|浅黄色旋转灯Ammeter|电流表Amperemeter Of Charge|充电电流表 Analog Input Card|模拟输入卡 Analog Output Card|模拟输出卡 Analysis Element|分析元件 Analysis Transmitter|分析变送器 Analyzer Element|分析元件 Analyzer Gas Warning Light|气体分析器报警灯Analyzer House|分析器房间 Analyzer Monitor System|分析器监控系统 Analyzer Switch High|分析器高开关 Analyzer Transmitter|分析变送器 Anchor Light|锚灯 Ancillary Skid|辅助撬 Angle Relief Valve|角安全阀 Annunciator|报警器 Annunciator Unit Arrangement|报警器装置 Antenna|天线Antenna Changing Switch|天线转换开关Antifoam INHIB. Storage Tank|消泡剂储罐 Antifoam Injection Pump|消泡剂注入泵Apision-Contr. Valve|Apision-Contr. Valve Artificial Lift Manifold|人工提升管汇Atmospheric Vent|通风口 Audible Alarm|报警器 Audio/Visual|Audio/Visual Auto Air Switch|气动开关 Auto. Shift Alarm|自转换报警 Aux. Lube Oil Pump|辅助润滑油泵 AUX. MCC For T/G|透平机组辅助电盘 Aux. Oil Pump|辅助油泵 Auxiliary Fuel Control Relay|辅助燃料控制继电器 Auxiliary Machine Control Panel|辅机控制盘 Auxiliary Relay|辅助继电器Auxiliary Terminal Strip|辅助端子排Auxilliary System|辅助系统Aviation Ligh|航空障碍灯 AVR-1 Out 24V 总电源 |AVR-1 Out 24V 总电源 AVR-1|电源自动调压器 AVR-2 220V 电源|自动调压器 AVR-2 24V 总电源|自动调压器 AVR-3 24V|自动调压器AVR-3 输出 24V|自动调压器 Axial Blower|轴流式风机 Axial Fan|轴流式风机 Axial Piston Motor|轴向柱塞马达 B Zone Operation Room|B 区控制开关间 B.O.P Control Unit|B.O.P 控制装置 Backup Lube Oil Pump|备用润滑油泵 Backwash Motor On Coase Filter Package|过滤器撬的反冲洗马达 Backwash Pump|反冲洗水泵 Backwash Return Pump|反洗水回转泵 Backwash Return Tank|反冲洗回转罐 Backwash Surge Tank Heater|反冲洗罐加热器 Backwash Tank|反冲洗水罐 Ball Valve|球阀 Ballast Pump|压载泵Bars Of Emergency Switchboard|应急配电盘的母排 Basket Strainer|篮式滤器 Bath RM|浴室 Battery|电池 Battery Box|电池箱 Battery Case|电池箱 Battery Charger|充电器Generator Control Panel|发电机控制盘 Battery For Navigation Aids System(Battery Bank For Navigation Aids System)|航行障碍灯系统的蓄电池 UPS|UPS Battery Light Panel|蓄电池灯配电盘 Battery Light Panel Distribution Board| 蓄电池分电箱 Battery Room|电池室 Battery Room Ex Fan|EX(EXHAUST) 电池间排风机 Battery System 电池系统Battery Tank 电池箱 Batteryroom 电池间 Analyzer 分析仪 Bed Light 床头灯 Bed RmBed Rm Normal Lighting|房间正常照明 Bell|铃 Bilge /Fire Pump Control Station|舱底/ 消防泵控制站 Bilge G.S. Pump Control Station|舱底气体泵控制站 Bilge Pump|舱底泵 Bilge/Fire Pump|舱底/消防泵 Bilge/Fire Pump Of Floor|底层的舱底/ 消防泵Bilge/General Serv Pump Of Floor|底层的舱底/总用泵 Biocide Injection Pump|生物杀灭剂注入泵 Biocide/Filter Aid Inj.Package|生物杀灭滤器辅助撬 Black & Jacket Heater For Emer.Generator|应急发电机缸套水加热器 Bleed Valve|泄放阀Block With Stop Vavles and Quick Conn.|Block With Stop Vavles and Quick Conn. Blow Down Valve|扫气阀Blowdown Orifice|孔Blowdown Pilot Valve|先导阀Blowdown Postion Switch|扫气位置开关 Blowdown Switch|扫气开关 Blowdown Vessel|扫气罐Blowdown Vessel Skid|扫气罐撬 Blower|风机 Blower Motor|风机电机 Blower Skid|风机撬 Blue Alarm Lamp|蓝色报警灯 Boat Lamp|艇灯 Boat Landing Platform|靠船平台 Boat Winch|艇绞车 Boat Winches|艇绞车 Boiler|锅炉 Boiler Control Box|锅炉控制箱Boiler Feed Pump|锅炉进水泵 Boiler Feed Tank|锅炉进水罐Boiler Make-up Pump 锅炉补水泵 Boiler Room 锅炉房 Boiler Room Ventilator 锅炉房通风装置 Boilers Area 锅炉区 Boom 吊臂 Hydraulic Motor 液压马达 Hoist Winch 提升绞车变幅系统 Boom Luffing System Boom Winch 变幅绞车 Boost Filter 辅助滤器Border Lights 边界灯 Both Side Type Speaker 双向型扬声器船舶绞盘 Bow Winch Bow Windlass 船舶绞盘 Bow Windlass Port 船舶绞盘端口 Bow Windlass Stbd|Bow Windlass Stbd Box For Emergency Generator 应急发电机接线箱救生衣箱 Box of Life Jackets Bracket Type Incadescent Light 支架型白炽灯 Bracket Type Incandescent Emergency Light W/Battery 带电池的支架型应急白炽灯 Bracket Type Incandescent Emergency Light W/Battery(Explosion-Proof) 40W 防爆带电池的支架型应急白炽灯 Bracket Type Mercury Vapour Light 支架型汞蒸气灯Bracket Type Mercury Vapour Light (Explosion-Proof) 200W 防爆型壁挂式汞蒸汽灯 Breath Apparatus 呼吸器 Breather Filter 呼吸过滤器 Bridge Between DRPW And GCP|DRPW 和 GCP 之间的桥 Bridge Walk Way (Between U/A Platform and D/P Platform)|架桥通道（生产平台和生活平台之间） Bulgy Valve Of Heat 热膨胀阀 Buoy 救生圈 Burner 燃烧器燃烧器控制器 Burner ControlBurner Element|燃烧器元件 Burner Flame Detector|燃烧器火焰探测器 Burner Motor|燃烧器马达 Burner Switch Low|燃烧器低压开关 Burner Trip Off&Alarm|燃烧器跳闸和警告 Burning Reposition Button|燃烧复位按钮 Burnre Trouble Show|燃烧器故障指示 Bus Tie|汇流排 Bus Tie & Syhchro Panel|母联和同步盘 Bus Tie ACB Panel|母联 ACB 盘 Bus Tie Panel|母联盘 Busbar Junctions|汇流排连接 Bush Buttom Key|钥匙型按钮 Bus-Tie 母联蝶阀 Butterfly Valve Buzzer 蜂鸣器 Bypass Seal Integrity 旁路密封完全 Bypass Transformer & Voltage Regulator & AC Distribution|旁路变压器、电压调节器和 AC 配电盘 Bypass Valve 旁通阀 Bypass Valve Actuator 旁通阀执行器 C Zone ESP Control Room C 区电潜泵控制间中央控制室 C.C.R Cabin heater 舱室加热器 Cabinet Air Conditioner 柜式空调 Cabinet Control Console 驾驶室控制台 Cabinet Control Panel 驾驶室控制盘柜式通风机 Cabinet Ventilation Fan Caisson 沉箱 Calibrated Sight Gauge to Indicate Lube Oil Level 液位计 Call Gas Bottle|Call Gas Bottle Camshaft|凸轮轴Camshaft Bearing 凸轮轴轴承Canopy Top Light 起航灯Capstan 绞盘Caretaker's Room 管理员房间 Ceiling Lamp Incandescent Light 吸顶灯（白炽）Ceiling Light With Emergency Bulb|带应急灯的吸顶灯 Ceiling Type Incandescent Emergency Light W/Battery 100W|吊顶式带电池应急白炽灯 Ceiling Type Mercury Vapour Light|吊顶式水银灯 Ceiling Type Mercury Vapour Light 200W|吊顶式汞蒸汽灯 Cellar Deck|底甲板 Cellar Shutdown Control Panel|底甲板关断控制盘 Celling Light With Emergency Bulb|应急球形天花板照明 Center Air Conditioner Sets|中央空调机组Central A/C Unit 400/400A|Central A/C Unit 400/400A Central Control Panel|中央控制盘 Central Control Room|中央控制室 Central Cooler|中心冷却器 Central Group Panel|中央组合盘 Central Group Panel CCR|Central Group Panel CCR Central Group Panel NAV Light|中央组合盘航行障碍灯 Centrifugal Blower|离心式风机 Centrifugal Brake|离心刹车器 Centrifugal Fan|离心式风机 Centrifugal Pump|离心泵 CGP|CGP CH4 Explosion-proof Detector|防爆、甲烷探测器 Change Box|更衣箱 Change room|更衣室Changing Room|更衣室 Charge Air Cooler|空气冷却器充电器 Charger|充电器 Check Valve|止回阀 Chemical Tank|化学罐Chemical Dosing Tank|药物添加罐Chemical Filling Pump|化学灌注泵 Chemical Injection Package|化学注入撬Chemical Injection Pump|化学注入泵 Chemical Injection Pump Of DEMULSIFIER|破乳剂注入泵 Chemical Injection Pump Of METHANOL|甲醇注入泵 Chemical Injection Pump Skid|化学注入泵撬 Chemical Injection Skid|化学药剂注入撬 Chemical Injection Storge Skid Heater| 化学注入存储撬加热器 Chemical Skid|化学撬 Chemical Storage Tank Heater|化学储油罐加热器 Chemical Storage Unit|化学存储装置 Chemical System Skid|化学系统撬 Chemical Tank Agitator|化学药剂罐搅拌器 Chemical Tank Heater|化学罐加热器 Chemical Transfer Pump|化学输送泵 Chengbei Oil Field Drilling And Production Platform|埕北油田钻井生产平台CHENGBEI Oil Field Utility And Accommodation Platform|埕北油田生活平台 Chill-Water Thermostat|冷水温度调节装置Chock Valve|节流阀Chock Valve(Manually Operated)|节流阀手动操作Choke Manifold|节流阀 Christmas Tree|采油树 Circulation Pump|循环泵 Clamp|夹具 Clean Water Booster Pump|清洁水增压泵 Clean Water Injection Pump|清洁水注入泵 Clean Water Injection Pump Skid|清洁水注入泵撬 Clean Water Surge Tank|清洁水缓冲罐Clean Water Surge Tank Heater|清洁水缓冲罐加热器Clean Water Surge Tank Skid|清洁水缓冲罐撬 Close Drain Vessel Heater|闭式排放罐加热器 Close Drain Vessel Pump|闭式排放泵 Close/Open Station Indicate Switch Of BDS|BDS 的开/关位置指示开关 Close/Open Station Indicate Switch Of MSSV|MSSV 的开/关位置指示开关 Close/Open Station Indicate Switch Of WSSV|WSSV 的开/关位置指示开关 Close/Open Station Indicate Swith Of ESDV|应急关断阀的开/关位置指示开关Closed Drain Heater|闭排加热器 Closed Drain Pump|闭式排放泵 Closed Drain Vessel|闭式排放罐 Closed Drain Vessel Heater|闭式排放罐加热器 Closed Drain Vessel Skid|闭式排放罐撬 Closed Drain/Diesel Injection Pump|闭式排放/柴油注入泵 Closed Drains Vessel Heater|闭式排放罐加热器 Closed Drains Vessel Pump|闭式排放泵Closed Drains Vessel Skid|闭式排放罐撬 Closing Life-Rescue Boat(Fire Protect)| 封闭式救生艇（防火型） CO2 Actuating Cylinder|二氧化碳启动罐 CO2 Area|二氧化碳区CO2 Bottle|二氧化碳气瓶 CO2 Control Panel|二氧化碳控制盘 CO2 Cylinder|二氧化碳瓶CO2 Discharge Nozzle(2)|二氧化碳喷嘴CO2 Extinguisher|二氧化碳灭火器CO2 Extinguisher Nozzle|二氧化碳灭火器喷嘴 CO2 Local Control Panel|二氧化碳现场盘CO2 Manual Release Control Box|二氧化碳手动释放控制盒CO2 Package|二氧化碳撬 CO2 Panel|二氧化碳盘 CO2 Portable Extinguisher|手提式二氧化碳灭火器 CO2 Release Box|二氧化碳释放盒 Coalescer|凝聚器 Coalescer Separator|凝聚器分离器 Coalescer Skid|凝聚器撬 Coarse & Fine Filter|粗&细滤清器 Coarse Filter|粗滤器 Coarse Filter Skid|粗滤器撬 COIC|COIC Cold Gas/Gas Exchanger|换热器Cold Gas/NGL Exchanger|冷煤气/液态天然气换热器Cold Room|冷藏室Cold Separator|冷分离器 Combustible Gas Detector|可燃气体探测器 Combustion Air and Exhaust Gas System|燃气和排气系统 Combustion Air Blower|助燃风机 Combustion Chamber|燃烧室Combustor 燃烧器Communicating Skid 通讯撬Communication & Fire/Gas Detection CONT. System 通讯&火灾/气体探测控制系统Communication Equipment 通信设备 Communication System| 通信系统 COMMUNICATIONS CONSOL| 通讯模块 Community Aerial Equipment|共用天线装置 Compass|罗经 Compound Gauge With Cock|带开关复式仪表 Compr.Lube Oil Filter.(STD)|压缩机滑油滤器 Compressed Air System|压缩空气系统 Compressoer B Starter Panel|压缩机 B 起动盘 Compressor|空气压缩机 Compressor Auto Prelube Pump|压缩机预润滑泵 Compressor Control And Annunciator Panel(VF)|压缩机控制仪表盘 Compressor Control Panel|压缩机控制盘Compressor Crankcase|压缩机曲轴箱Compressor Diffuser|扩压器 Compressor Lube Oil System|压缩机滑油系统 Compressor Motor|压缩机电动机 Compressor Oil Cooler|压缩机滑冷却器油 Compressors Area|压缩机区Compund Control Unit|Compund Control Unit Computer For Data Logger|数据记录计算机 Condensate Drum Skid|冷凝罐撬 Condensate Pump|冷凝泵 Condensate Sep|Condensate Sep Condensate/Gas Filed|Condensate/Gas Filed Condensator|冷凝器 Condenser|冷凝器 Conductor Installation Deck|隔水套管安装甲板 Cone Type Speaker|锥型扬声器Connecting Rod|连杆 Connecting Rod Bearings|连杆轴承 Contactor|接触器 Contactor Tank|接触器箱 Control Ball Valve|控制球阀 Control Box|控制箱 Control Butterfly Valve|控制蝶阀 Control Cabinet|控制室 Control Console,Local|就地/现场控制箱Control Logic Module|控制逻辑模块 Control Panel|控制盘 Control Panels|控制盘Control Power Board|控制动力盘 Control Room|控制室 Control Valve|控制阀 Coolant Filter|冷却剂滤器Coolant Heater|冷却剂加热器Coolant System|冷却系统Cooler|冷却器Cooler Assembly|冷却器总成 Cooler Core (Air)|冷却器芯（气） Cooler Core(Oil)|冷却器芯（油）Cooler Motor|冷却器马达 Cooling Fan|冷却风机 Cooling System|冷却系统 Cooling Water Pump|冷却水泵 Cooling Water Pump For Methanol Injection Pump|甲醇注入泵的冷却水泵 Cooling Water Pump For Open Drain Pump|开式排放泵的冷却水泵 Cooling Water Skid|冷却水撬 Cooling Water System|冷却水系统 Corresion Inhibiter Injection Pump|防腐剂注入泵 Corresion Inhibiter Mixer|防腐剂搅拌器 Corresion Inhibiter Storage Tank|防腐剂储存罐 Corresion Inhibiter Tank Heater|防腐剂罐加热器 Corridor|走廊Corrugated Plate Interceptor|波纹板收集器 Corrugated Plate Interceptor Skid|波纹板收集器撬Coupling|连轴器Coupling Guard|连轴器护罩Cran Termination Relay|Cran Termination Relay Crane|吊机 Crank|曲轴 Crankcase|曲轴箱 Crankshaft|曲轴 Crankshaft Front Seal And Wear Sleeve|Crankshaft Front Seal And Wear Sleeve Crankshaft Main Bearings|曲轴主轴承Crankshaft Rear Seal And Wear Sleeve|Crankshaft Rear Seal And Wear SleeveCrankshaft Vibration Damper|曲轴减震器 Crash Pump|曲轴泵 Crude Cooler|原油冷却器 Crude Cooler Skid|原油冷却器撬 Crude Drain Tank|原油排放罐 Crude Export Pump|原油外输泵 Crude Filter Skid|原油过滤器撬 Crude Heat Exchanger|原油热交换器 Crude Heat Exchanger Skid|原油热交换器撬 Crude Loading Pump|原油外输泵 Crude Loading Pump Skid|原油外输泵撬 Crude Offloading Metering Package And Meter Prover|原油外输计量撬和计量仪表 Crude Oil Export Pump|原油外输泵 Crude Oil Filter|原油滤器Crude Oil Filter Skid|原油滤器撬 Crude Oil Transfer Pump|原油输送泵 Crude Oile Export Pump & Water Injection Pump|原油外输泵和注水泵 Crude PIC Valve PIC|阀 Crude Preheater|原油预热器 Crude Service Tank|原油储存罐 Crude Storage Caisson Heater|原油沉箱加热器 Crude Storage Caissons|原油沉箱 Crude Transfer Pumps Control Panel(P-101A)|原油输送泵控制盘 CTREE|采油树 Cu-Al Electrolyzer|铜－铝电解装置Current Transformers|电流互感器 Cyclone Appliance Nozzle|旋流喷嘴 Cyl. Weight Scale|Cyl. Weight Scale Cylinder|(汽,气,油,水)缸组件 Cylinder Head|缸头 Cylinder Liner|缸套 Cylinder Pin|缸销 Cylinder Selection Switch|气缸选择开关 D Zone ESP Transformer Room|D 区电潜泵变压器间D.E. Main Fire Pump Room|柴油机驱动主消防泵间 D.O. Preheater|柴油预热器 D.O. Pump For Main Burner|主燃烧器的柴油泵 D.O. Pump For Pilot Burner|预燃烧器柴油泵 D.O. Purifier Of A Deck A| 甲板柴油净化器 D.O. TK For Boiler|锅炉的柴油罐 D.O. TK. For Thermal Oil Heaters|热介质炉柴油罐 . For I.G.G|惰气发生器柴油罐 D/G Control Panel|D/G 控制盘 Daily Diesel Filter|日用柴油过滤器 Daily Diesel Filter Skid|日用柴油过滤器撬 Daily Diesel Pump Skid|日用柴油泵撬 Daily Diesel Tank|日用柴油罐Daily Diesel Tank Heater|日用柴油罐加热器Damper|Damper Damper Snap-acting Switch|风闸动作开关 Damper Solenoid Valve|风闸电磁阀 Danger Signal Light(Red)(P. Side)|危险信号灯（红） Davit And Winch For Survival Craft|救生艇机和绞车 Davit For Rescue Boat|救生艇的起艇机 Davit For Survival Craft|救生艇的起艇机DC Motor|直流马达Deaerating Valve|脱气阀Debutanizer|脱丁烷塔Debutanizer Reboiler|脱丁烷塔再沸器 Debutanizer Reflux Condenser|脱丁烷塔回流冷凝器 Debutanizer Reflux/Product Pump Skid| 脱丁烷塔回流/生产泵撬 Debutanizer Rflux Drum|脱丁烷塔回流罐 Deck -Mounter Fixed Tank Washing Machine|Deck -Mounter Fixed TankWashing Machine Deck Seal Heater|甲板水封加热器 Deck Seal Tank|甲板水封罐 Deck Seal Tank Skid|甲板水封罐撬 Deethanizer|脱乙烷塔 Deethanizer Reboiler|脱乙烷塔再沸器 Deethanizer Reflux Condenser|脱乙烷塔回流冷凝器 Deethanizer Reflux Drum|脱乙烷塔回流罐 Deethanizer Reflux Pump Skid|脱乙烷塔回流泵撬 Defoamer Injection Pump|消泡剂注入泵 Defoamer Mixer|消泡剂搅拌器 Defoamer Storage Tank|消泡剂储存罐 Defoamer Storage Tank Heater|消泡剂储存罐加热器 Degasser|脱气装置 Dehydrator Feed Pump|脱水器进给泵Dehydrator Feed Pump Skid|脱水器给水泵Dehydrator Preheater|脱水预热器 Dehydrator Preheater Skid|脱水预热器撬 Deluge Nozzle|水喷淋头 Deluge Nozzle System|水喷淋系统 Deluge Release Solenoid Valve|水喷淋释放电磁阀 Deluge System|喷淋系统 Deluge Valve|水喷淋阀 Deluge Valve Station|水喷淋阀站Demethanizer|脱甲烷塔Demethanizer Bottoms Pump Skid|脱甲烷塔底泵撬Demethanizer Reboiler|脱甲烷塔再沸器 Demister|除雾器 Demulsfier "B" Mixer|破乳剂 B 搅拌机 Demulsifer "B" Injection Pump|破乳剂 B 注入泵 Demulsifier Storage Tank|破乳剂储存罐 Demulsifier Storage Tank Heater|破乳剂储存罐加热器Demulsifier Injection Pump|破乳剂注入泵Demulsifier Pump|Demulsifier Pump Demulsifier Storage Tank|破乳剂储存罐 Demulsifier Tank|破乳剂罐 Demulsifier Tank Heater|破乳剂罐加热器 Demulsifier Tank Mixer|破乳剂罐搅拌器 Density Elevent|Density Elevent Density Transmitter|密度传送器 Deposit Tank|沉淀罐Depropanizer|脱丙烷塔Depropanizer Reboiler|脱丙烷重沸器Depropanizer Reflux Condenser|脱丙烷逆流冷凝器 Depropanizer Reflux Drum|脱丙烷逆流罐Depropanizer Reflux/Product Pump|脱丙烷逆流/生产泵Depropanizer Reflux/Product Pump Skid|脱丙烷逆流/生产泵撬 Desander|除沙器 Desander Package|除沙器撬 Desk Top Telephone|台式电话 Diesel Boiler|燃油锅炉 Diesel Daily Tank|柴油日用柜/罐 Diesel Day Tank Heater|柴油日用罐加热器 Diesel Day Tank Module|柴油常用柜/ 罐模块 Diesel Day Tank Skid|柴油日用柜/罐撬 Diesel Engine|柴油发电机Diesel Filter|柴油滤器 Diesel Filter Skid|柴油滤器撬 Diesel Holding Tank Heater|柴油柜加热器 Diesel Oil Heater|柴油加热器 Diesel Oil Pump|柴油泵 Diesel Oil Pump Manual(Automatic) Control|柴油泵手动(自动)控制 Diesel Oil Pump Motor|柴油泵电动机Diesel Oil System|柴油系统 Diesel Oil TK. For Fire Pump|消防泵的柴油柜 Diesel Storage Tank|柴油存储罐 Diesel Storage Tank Heater|柴油储存罐加热器 Diesel TRANS. Pump|柴油输送泵Diesel Transfer Pump Skid|柴油输送泵撬Different Pressure Indicator|差压指示器 Different Pressure Switch High|高差压开关 Differentia Pressure Gage|差压表Differential Current Transformer|差动电流互感器Differential Pressure Converter|差压转换器Differential Pressure Indicating Controller|差压指示控制器 Differential Pressure Regulator Valve|差压调节阀Differential Pressure Self Contained Regulator|自力式差压调节阀 Differential Pressure Switch|差压开关Differential Pressure Switch High|高差压开关Differential Pressure Transducer|差压传感器 Differential Pressure Transmitter|差压变送器Dining Room|餐厅Air-Condition|空调Discharge Louver|卸货天窗Discharge Louver/Damper|排气百叶窗/ 风闸Discharge Muffler|排气消声器Discharging Indicator|放电指示表 Discrete Input Card|离散输入卡 Discrete Output Card|离散输出卡 Disel Engine|柴油发动机 Dispersed Gas Floatation|气体浮选器Dispersed Gas Floatation Skid|气体浮选器撬 Displacement Oil Pump|置换油泵Disposal Well Pump|井处理泵 Disposed Gas Floator (Rotor)|处理气浮选器（转子） Dist Panel|Dist Panel Dist Panel (A/C Handing NO.1)|Dist Panel (A/C Handing NO.1) Dist Panel Air/C Comp|Dist Panel Air/C Comp Dist Panel Cooking Equipment|Dist Panel Cooking Equipment Dist Panel Egg|Dist Panel Egg Dist Panel Laboratory Room AC Unit|Dist Panel Laboratory Room AC Unit Dist Panel Metering Unit|Dist Panel Metering Unit Dist Panel Seivage Treat|Dist Panel Seivage Treat Dist. Panel|分电盘 Dist. Panel For Communication(In Radio Room)|报房通讯分电箱Dist. Panel For Fire Dampers(W2-DP-DP1)| 防火风闸分电箱 Dist. Panel For Galley|楼道分电箱 Dist. Panel For Living Quarter Fire Dampers(W2Q-DP-DP2)|生活模块防火风闸分电箱Distribution Box|分电箱 Distribution Panel|配电盘 Distribution Panel For Main Generator| 主机分电盘 Distribution Panel For Normal Communication System|正常通讯系统分电盘 Do Not Enter Warning|禁止进入警告 Do Not Enter Warning Light|禁止进入警灯 Door Closer|闭门器 Door Switch|门开关 Double Fire Indicator|双精度型火灾指示器 Double Pilot Operated Non Return Valve|双作用止回阀DP I Distribution Panel DP I| 分配电盘 Drain Pit|泄放池 Drain Pit Skid|泄放池撬 Drain Plug Arrangement|排放塞子布置 Drain Pump|排放泵 Drain Valve|排放阀 Drier Package|干燥器撬 Drilling & Accommodation Wellhead Platform|钻井&生活井口平台Drilling Deck|钻井甲板 Drilling Machine|钻机 Drive Board|驱动控制板 Drivers Cabin|驾驶舱 H.M. Drain Pump|热介质排放泵 Dry Chemical Cylinder|干粉瓶 Dry Chemical Extinguisher|干粉灭火器 Dry Chemical Extinguisher Skid|干粉灭火器撬 Dry Chemical Hand Extinguisher|干粉手动灭火器 DRY CHEMICAL TANK|干粉箱 Dry Gas Dust Filter Skid|干燥气除尘过滤器撬Dry Goods RM|储物间Drychemical Portable Extinguisher|手提干粉灭火器 Dryer Ctl Panel|干燥器控制盘 Dryer Filter|干燥器过滤器 Dryer Package|Dryer Package Dryer Tower|干燥器塔 Drying Oven|干燥器 DS-7 Conductivity Meter|DS-7 型电导计 DSC/Watch Receiver|DSC/Watch 接受器 DSC-60 DSC/WATCH Receiver|DSC-60 DSC/WATCH 接受器 Dual Agent Nozzle|双介质喷嘴 Dual Fuel System|双燃料系统 Hydraulic Pump|液压泵 Duct Nozzle|管型喷嘴 Duplex Filter|双联过滤器Duplex Oil Filter|双联油过滤器 Duplex Stainer|双联滤器 Duty Room|值班室 E & I Room|电气仪表间 E.S.B Feeder Panel|电潜泵供电开关盘 E.S.P Control Room|电潜泵控制室 E.S.P Transformer Package|电潜泵变压器撬 E/P Positioner|E/P Positioner Economizer|节料装置 Effluent Watertank|污水储存罐 Ele.Bath Heater|洗澡水电加热器ELE.Test|电测 Elec. Heater|电加热器 Elec. Lube Oil Heater|润滑油电加热器 Elec. Main Fire Pump|电动主消防泵 Elec-magn. Valve|电磁阀 Elect.Room|电气室 Electical Horn For Fire|火灾报警电笛 Electric Bath Heater Control Panel|洗澡水电加热器控制盘 Electric Bell|电铃 Electric Control Box|电控箱 Electric Dehydrator|电脱水器Electric Dehydrator Skid|电脱水器撬 Electric Desalter|电脱盐器 Electric Desalter Skid|电脱盐器撬 Electric Glycol Pumps|三甘醇电泵 Electric Modulating Valve|电调幅阀 Electric Starter|电启动器 Electric Submersible Pump Control Room|电潜泵控制室 Electric Submersible Pump Transformer| 电潜泵变压器 Electric Welder|电焊机Electrical Heater Box|电加热控制盘 Electrical Lighting Skid|照明撬 Electrical Room|电气室Electrical Switch Room|电气开关间Electro Static Treter Transformer|Electro Static Treter Transformer Electromagnetic oil valves|电磁阀Electronic Governor|电子调速器 Electronic Governor Relay|电子调速器继电器 Electronic Pressure Transmitter|电子压力变送器 Electrostatic Treater|静电处理器 Element.Inlet Filt.|入口过滤器元件 Emengency Incandescent Lamp With Battery Explosion-Proof Type(40w)|防爆型带电池的应急白帜灯 Emengency Light Skid|应急照明撬 EMER Generator Block Heater|应急发电机缸套水加热器 Emer. Generator Control Panel|应急发电机控制盘 Emer. Lighting & Small Power Switchboard|应急照明和小功率配盘 Emer.Gen.RM|应急发电机间 Emerg Heat Tracing Switchboard|应急电伴热配电盘 Emergency 220V Heat Tracing Switchboard|220 伏应急电伴热配电盘 Emergency 220V Heating Tracing Switchboard|220 伏应急电伴热配电盘 Emergency 220V Power & Lighting Switchboard|220 伏应急照明和小功率配电盘Emergency AC220V Feeder Panel|220 伏 AC 应急供电开关盘 Emergency Day Tank|应急日用罐 Emergency Diesel Generator|应急柴油发电机 Emergency Diesel Generator Skid|应急柴油发电机撬Emergency Displace Pump|应急置换泵 Emergency Displace Pump Skid|应急置换泵撬Emergency Explosion-proof Project Light|应急防爆投光灯 Emergency Fire Pump Area|应急消防泵区 Emergency Fire Pump Room Draft Fan| 应急消防泵室风机 Emergency Fuel Control Relay|应急燃油控制继电器 Emergency Generator & LE/LC BusPanel|应急发电机和 LE/LC 母联盘 Emergency Generator Remote Control Panel|应急发电机遥控盘 Emergency Generator Room Ventilator| 应急发电机房通风机 Emergency Genset AC Junct Box|应急发电机组交流接线箱 Emergency Heat Tracing Distribution Board|应急电伴热配电盘 Emergency Heat Tracing Switchboard| 应急电伴热配电盘Emergency Heat Tracing Transformer|应急电伴热变压器 Emergency Incandescent Lamp With Battery|带电池的应急白炽灯Emergency Incandescent Lamp With Battery Explosion-Proof Type|带电池的防爆应急白炽灯 Emergency Incandescent Lamp With Battery Of DN|带 DN 电池的应急白炽灯 Emergency Incandescent Lamp With Battery Of Down|带电池的应急白炽灯 Emergency Light|应急灯 Emergency Light Dist Panel|应急照明分电箱Emergency Light Panel|应急照明盘Emergency Light Skid|应急灯撬Emergency Lighting|应急照明Emergency Lighting Fixture Pendant Mount (High Intensity Dischange)|固定垂挂装配的应急灯 Emergency Lighting Self Contained Battery Type Indoor Use Explosion-Proof|自带电池室内防爆应急灯Emergency Lighting System|应急照明系统 Emergency Lighting Transformer|应急照明变压器Emergency Lighting Transformer|应急照明变压器 Emergency Lighting/Utilities|应急照明/ 公用设施Emergency Lighting/Utility Trans.|应急照明/公用设施变压器 Emergency Lights Distribution Panel|应急照明分电盘 Emergency MCC|应急马达控制中心 Emergency Motor Control Center|应急马达控制中心 Emergency Position Swtich|应急限位开关Emergency Power Generator Engine Control Box|应急发电机发动机控制盒 Emergency Radar Transducer|应急雷达应答器 Emergency Radar Transponder Sart 9,2-9,5GHz|应急雷达应答器 Emergency Sb Room Ex Fan|应急 SB 室排风机 Emergency Shutdown|应急关断 Emergency Shutdown Button|应急关断按钮 Emergency Shutdown Valve|应急关断阀Emergency Stop Value|应急关闭阀 Emergency Supply System|应急供电系统 Emergency Switch Board|应急开关板 Emergency Switch Room|应急开关间 Emergency Switchboard|应急开关板 Emergency Transformer|应急变压器 Emergency Trip Off Alarm|应急跳闸报警 Enclosure|撬 Enclosure Exhaust Gas Sensor|撬排气传感器 Enclosure Exhaust Transmitter|围栏排气变送器 Enclosure Inlet Gas Sensor|撬进气传感器 Enclosure Vent Fan|撬排风机 Engine|发动机 Engine Driven Cooling Water Pump(Engine-Mounted Coolant Pump)| 机带冷却水泵 Engine And Gear Box|发动机和齿轮箱Engine Compressor Discharge Pressure Gage|压缩机压力表 Engine Control Switch|发动机控制开关 Engine Controller|发动机控制器 Engine Cooling System|冷却系统Engine Driven Fuel Pump|机带燃油泵 Engine Driven Lube Oil Pump|机带滑油泵 Engine Failure Relay|发动机故障继电器 Engine Fuel System|燃油系统 Engine Liquid Fuel Pressure Gage|机油压力表 Engine Lube Oil System|滑油系统 Engine Oil Pressure Indicator|发动机油压指示计Engine Oil Temperature Indicator|发动机温度计Engine Sabb Motor|发动机 Sabb 电动机 Enlcosure Standby Light|撬备用灯 Entire Enclose Refrigerant Compressor| 整体围栏冷冻压缩机EP-12 0.36Kw W2-M-101/102|EP-12 0.36Kw W2-M-101/102 Equipment Skid|设备撬 Equipment Tank|装备箱 ESD|ESD ESP Control Room|电潜泵控制间 ESP Control Room CO2 Manifold|电潜泵间二氧化碳管汇 Esp Transfermer Room|电潜泵变压器间 Evacute Immediate Warning|即时警报 Evacute Immediate Warning Light|即使警报灯 Evaporator|蒸发器 EX Fan|排气风机 Excitation Panel|励磁控制盘 Exciter|励磁器 Exhaust Bellows And Silencers|膨胀接头和消声器 Exhaust Diffuser|扩散器 Air Comperssor Room|空压机房 Battery Room|电池间。

海洋石油英语 Electric heating cable 加热电缆field development 油田开发flexible riser 挠性隔水管heating line 加热管线‘host’ platform “主”平台‘surface’ conductor “表层”导管“dual bore” type tree “双筒”型采油树 “temporary” guide base “临时”导向基座 “two stack” approach “双防喷器组”法 Abandonment and Recovery 弃置与回收 acceptance criteria 验收标准Acceptance Test 验收测试accumulator bottle 蓄能器瓶alignment 找正alternating current 交流电ambient seawater temperature 周围海水温度 ambient temperature 环境温度ancillary equipment 辅助设备annular space 环形空间annulus bore 环空孔annulus master valve 环空主阀 annulus seal assembly 环空密封总成anti-rotation pin 防旋转销armour wire 铠装线armours layer 铠装层artificial lift 人工举升artificial lift method 人工举升法 Asgard project Asgard项目Atmospheric Diving Suit 常压潜水服 atmospheric pressure 大气压力 attachement point 固着点Austenitic Stainless Steel 奥氏体不锈钢 austenitic-ferric steel 奥氏体-铁素体钢 auto depth 自动定深automatic connector 自动连接器average unevenness height 平均不均匀高度 axial tension 轴向拉力backing steel 背钢backup function 备份功能barrier coating 防护涂层barrier protection 隔层保护basic oxygen furnace 碱性氧气转炉basket storage carousel 篮式存管盘bend limiter 弯曲限幅器bend radius 弯曲半径bend restrictor 弯曲限制器bend stiffener 弯曲加强杆bending loads 弯曲载荷bending moment 弯曲力矩bending reaction ring 弯曲止推环 bending stiffness 抗弯刚度bending stress 弯曲应力Billet piercing process 坯板料穿孔工艺 bleed valve 泄放阀blind cap 盲帽block valves 断流阀bypass valves 旁通阀Blowout Preventer 防喷器bollard pull 系缆拉力bolt flange connection 螺栓法兰连接 bolted flange connection 螺栓法兰连接 BOP connector 防喷器连接器BOP pipe ram 防喷器管闸板BOP Stack 防喷器组Bore Protector 井筒保护器 bottom crawling vehicle 海底爬行车 Buckle propagation 弯曲传播buckle propagation 弯曲传播Bull Nose 圆头管堵bundle 管束buoyancy module 浮力块Campos basin Campos盆地carbon steel 碳钢Carbon steel tube 碳钢管Carbon-Manganese steel pipe 碳锰钢管 carrier pipe 输送管Casing Hanger 套管悬挂器casing pup joint 套管短节catenary curve 悬链曲线catenary shape 悬链线型cathodic protection 阴极保护 detection system 检测系统 Centrifugation Process 离心工艺 Check Valve 止回阀chemical fluids 化学流体chemical injection 化学剂注入choke actuator 油嘴促动器choke insert 油嘴嵌件choke position 油嘴位置circuit breaker 断路器circuit length 电路长度circulate hot water 循环热水clad corrosion resistant alloy 复合防腐合金Clad Metal 复合金属clad pipe structure 复合管结构Clad pipe system 复合管系统clamp connector 紧固连接器clamp hub 卡箍Class I 第一类Class II 第二类Class III 第三类Class IV 第四类C-Mn steel pipe 碳锰钢管coating defect 涂层缺陷Coil tubing 连续油管coiled skelp 挠性管材collet connection 套管连接collet connector 套管连接器Completion / Workover Riser System 完井/修井隔水管系统 completion equipment 完井设备completion guide base 完井导向基座 Completion Guidebase 完井导向基座 completion riser system 完井隔水管系统 Component Change-Out tool 部件更换工具 composite armour 复合铠装composite armour layer 复合铠装层 composite material 复合材料compression force 压缩力compressive load 压缩载荷concentric tubing hanger 同心油管悬挂器 Conductor Housing 导管头conductor resistance 导体电阻conductor string 导管柱Connection/reaction loads 连接/反作用载荷 Connector profile 连接器剖面Continuous lamination 连续分层continuous length 连续长度continuous slab caster 板坯连铸机 continuous strand caster 流坯连铸机 control cabin 控制舱control fluid 压井液Control Function 控制功能Control junction plate 控制连接板control module 控制模块control pod 控制盒control room 控制室Control Station 控制站control umbilical 控制脐带管control valve 控制阀conventional style trees 常规型采油树 Conventional Tree 常规采油树correct orientation 正确方向corrosion allowance 腐蚀裕量corrosion control 腐蚀控制corrosion inhibition 腐蚀抑制corrosion inhibitor 缓蚀剂CORROSION MONITORING 腐蚀监控corrosion protection 腐蚀防护corrosion protection system 腐蚀防护系统 corrosion rate 腐蚀速度corrosion resistance 耐腐蚀corrosion resistant alloy 耐腐蚀合金 corrosion resistant materials 耐腐蚀材料 corrosive agent 腐蚀剂corrosive environment 腐蚀性环境coupler hydraulic 接头液压CROSS SECTION 截面cross sectional area 截面面积Cross Wound Polyethylene 交叉卷绕聚乙烯 cross-flow oscillations 横流振动cross-section 截面crushing load 压碎载荷residual strain 残余应变Cumulative strain deformation 累积应变变形 cumulative strain 累积应变current drag 海流阻力Current Limiter 限流器current loads 海流载荷current saturation 当前饱和current velocity 海流速度cylindrical billet 圆柱坯料data collection 数据采集data sheets 数据表data transmission 数据传输DC conductor resistance 直流导体电阻Dead Weight 船舶载重量debris cap 岩屑帽deck level 甲板水平面deck load 甲板载荷Deck space 甲板空间deep water 深水deepwater developments 深水开发deepwater field development 深水油气田开发DEEPWATER FIELD DEVELOPMENT REFERENCE BOOK 深水油气田开发参考手册deepwater flowline 深水出油管线deepwater pipeline 深水管道DEEPWATER REFERENCE BOOK 深水参考手册deepwater riser 深水隔水管Destructive Examination 破坏性检验development option 开发方案Differential Global Positioning System 差分全球定位系统 Differential Pressure 压力差Digging chain 开挖链direct current 直流Direct Heating System 直接加热系统Directional Control Valve 方向控制阀 Distributed Control System 分布式控制系统 distribution piping systems 分配管道系统 distribution system 配电系统Distribution Unit 分配装置Diving Support Vessel 潜水供应船Dolly base 转管滚座downhole gauges 井下压力计Downhole Pressure 井下压力Downhole Safety Valve 井下安全阀drag loads 拉力载荷drill pipe string 钻杆柱drilling operation 钻井作业drilling riser 钻井隔水管Driving wheel 驱动轮Dual Bore Split Body Tree 双筒拼合本体采油树 dual bore subsea tree 双筒水下采油树dual bore tree 双筒采油树dual redundant 双冗余dual SEMs 双SEMDual Systems 双机系统Duplex stainless pipe 双相不锈钢管Duplex stainless steel 双相不锈钢Dynamic analysis 动态分析Dynamic positioning 动力定位dynamic positioning (DP) system 动力定位系统 dynamic positioning system 动力定位系统dynamic response 动态响应dynamic riser 动力隔水管dynamically positioned lay vessel 动力定位铺管船 Earth continuity test 接地连续性试验Edge trimming 切边edge-crimping 卷边Effective tension 有效张力electric cable 电缆electric current 电流electric heating 电加热electric power 电力Electric Power Unit 电力装置electric pump 电动泵electric resistance welded 电阻焊Electric resistance welded pipe 电阻焊管electric submersible pump 电动潜油泵electrical cable 电缆electrical component 电气部件 electrical conductor 电气导线Electrical connection 电气连接electrical connector 电气连接件electrical current 电流Electrical Distribution Unit 配电装置Electrical electrode 电极Electrical Flying Lead 电引线Electrical isolation 电气隔离Electrical Jumper 电气跨接线Electrical junction box 电气接线盒electrical motor 电动机electrical noise 电噪音Electrical penetrators 电动穿孔器Electrical Power Unit 电力装置ELECTRICAL POWER UNIT 电力装置（EPU）electrical pump 电动泵Electrical signal 电信号Electrical Umbilical 电气脐带管electric-arc furnace 电弧炉electric-welded pipe 电焊接管electro-hydraulic control systems 电动液压控制系统electro-hydraulic multiplexed subsea control system 电动液压多路复用水下控制系统Electro-hydraulic umbilical 电动液压脐带管 electronic components 电子元件Emergency Shut Down 应急关断empirical curve 经验曲线empirical uplift coefficient 经验上提系数 end fitting 端部配件end riser termination 端部隔水管终端 environment loads 环境载荷environmental condition 环境条件 environmental loads 环境载荷ERW line pipe 电阻焊管线ESD sequence 应急关断顺序ESD signal 应急关断信号export line 输送管线external corrosion 外部腐蚀external diameter 外径external hydrostatic pressure 外部静水压力 external pressure 外部压力External Welding 外部焊接Extrusion Process 挤压工艺Extrusion throat 挤压式喉管 fabrication 制造fabrication times 制造时间Factory Acceptance Test 工厂验收试验fatigue damage 疲劳损坏fatigue life 疲劳寿命female connector 母连接器female couplers 母接头female couplings 母接头fibre optic 光纤fibre optic cables 光纤电缆fibre optic technology 光纤技术field development 油气田开发field joint 现场连接接头field life 油田寿命Field Signature Method (FSM) stations FSM技术检测点（备注：FSM是挪威CorrOcean公司开发的一种新型无损检测技术）final position 最终位置Firing line 流水作业线first-line barrier protection 一级隔层保护Flex joint 挠性接头flexible flowline 挠性出油管线flexible jumper 挠性跨接管flexible laying system 挠性管铺设系统 flexible line 挠性管线flexible pipe flowlines 挠性出油管线 flexible pipe structure 挠性管结构 Flexible pipe system 挠性管系统flexible riser 挠性隔水管Flexible storage carousel 挠性管存管盘 flexible structure 挠性结构flexible subsea pipe 挠性水下管道Flexible technology 挠性技术floating production 浮式采油floating production platform 浮式采油平台 floating production system 浮式采油系统 Flow Line 出油管flow meter 流量计Flowbase 出油基座fluid barrier 流体隔层fluid characteristics 流体特性fluid compatibility 流体相容性fluid level 流体液位fluid samples 流体样本fluid temperature 流体温度 FPS motion FPS运动Free Hanging 自由悬挂free standing 自由竖立Frequency Shift 频移friction coefficient 摩擦系数full bore annulus circulation 全井筒环空循环 Functional requirements 功能要求fusion-bonded epoxy 热熔结环氧Gas compressor 气体压缩机gas export line 天然气输出线路gas export line 天然气输出线路gas lift 气举Gas lift line 气举管线Gas Metal Arc Welding 气体保护金属极电弧焊 gas pipeline 天然气管道Gas pipeline system 天然气管道系统gas trunkline 天然气干线Gas Tungsten Arc Welding 钨极气体保护电弧焊 general arrangement 总体布局general arrangement 总体布置general corrosion 全面腐蚀Gimbal 常平架Girth welds 管道环形焊缝Global Positioning System 全球定位系统 gravel pack 砾石充填green canyon Green峡谷grit blasting 喷钢砂guide frame 导向架guide funnel 漏斗形导向承口guide pin 导向销guide pin 导向销guide pin 导向销guide post 导向柱guide sleeve 导向套guide wires 导向绳Guideline Drilling 导向绳钻井Guiding roller 导向滚轮hammer unions 锤击由任hand valve 手动阀Hazardous Area 危险区Heat Affected Zone 热影响区Heat soak tests 热浸试验Heat tracing 伴热heat tracing 伴热 heat transfer 热传导heat transfer 热传导heat transfer 热传导heat treatment 热处理heating lines 加热管线heating system 加热系统heating technique 加热技术helical strake 螺旋箍条High Collapse Resistance 高抗挤毁（性）high collapse resistance hose 高抗挤毁（HCR）软管 high cost 高成本High Density 高密度High Density Polyethylene 高密度聚乙烯high frequency alternative current 高频交流电流 high lay tensions 高敷设张力high pressure 高压high pressure jets 高压喷射装置high procurement cost 高采购成本HIGH TEMPERATURE 高温high-density 高密度hollow glass micospheres 空心玻璃微球hollow glass microsphere 空心玻璃微球hoop strength layer 环向强度层horizontal 水平horizontal connection 水平连接Horizontal Connector 水平连接器horizontal plane 水平面horizontal position 水平位置Horizontal powered reel 水平动力卷轴horizontal reel 水平卷轴horizontal subsea Christmas tree 水平水下采油树 horizontal subsea tree 水平水下采油树horizontal tree 水平采油树Horizontal Tree stinger 水平采油树插入管hose liner 软管内衬hose liner 软管内衬Host' platform “主”平台Hot fluid 热流体Hot rolling clad pipe 热轧复合管Hot rolling process 热轧工艺hot stab 热入扣hot-rolling mill 热轧机hot-stab 热入扣hybrid riser 复合隔水管 hybrid riser system 复合隔水管系统hybrid riser tower 复合隔水管塔hybrid riser tower 复合隔水管塔hydrate formation 水合物形成hydrate formation temperature 水合物形成温度 hydraulic 液压Hydraulic Analysis 液压分析hydraulic connection 液压连接部分hydraulic connectors 液压连接器Hydraulic coupler 液压接头Hydraulic Couplers 液压接头hydraulic couplings 液压接头hydraulic couplings 液压接头Hydraulic cylinder 液压缸Hydraulic Distribution 液压分配Hydraulic Distribution Module 液压分配模块 hydraulic expansion method 液压膨胀法 hydraulic fluid 液压油hydraulic fluid 液压液Hydraulic fluid cleanliness 液压液清洁度 hydraulic flying leads 液压引线hydraulic function 液压功能hydraulic galleries 液压坑道 Hydraulic Hoses 液压软管 hydraulic interface 液压接口 hydraulic jet pump 水力喷射泵 hydraulic line 液压管线hydraulic line 液压管线Hydraulic lock 液压锁hydraulic motor 液压马达 Hydraulic oil 液压油Hydraulic output 液压输出 Hydraulic Power Unit 液压动力装置 hydraulic press 液压机hydraulic pressure 水压hydraulic pressure 水压hydraulic supplies 液压供应 hydraulic supply 液压供应 Hydraulic Supply 液压供应 Hydraulic System 液压系统 Hydraulic tubes 液压管hydraulic umbilicals 液压脐带管 hydrodynamic load 水动力载荷 hydrogen embrittlement 氢脆变 hydrogen embrittlement 氢脆变Hydrogen Induced Cracking 氢致开裂 hydrostatic collapse 静水压挤毁hydrostatic pressure 静水压力I.D. punch 内径穿孔Indicator rod 指示杆Induction cable 感应电缆Induction current 感应电流induction heating 感应加热Induction Welded pipe 感应焊管Induction Welding 感应焊接In-house experience 内部经验In-house technical database 内部技术数据库 injection fluids 注入流体injection line 注入管线injection of chemicals 化学剂注入injection point 注入点injection point 注入点injection point 注入点Injection Valves 注入阀injection well 注入井in-line oscillations 平行振动inner pipe 内管Insert choke 嵌入式油嘴installation 安装installation 设备（一般大型设备，注意文中是否有出现）installation method 安装方法installation methods / sequences 安装方法/安装顺序 installation parameters 安装参数installation phase 安装阶段installation procedure 安装程序installation process 安装过程installation processes 安装过程installation technique 安装技术installation tolerances 安装公差Installation tolerances 安装公差Installation Vessel 安装船Installation vessels 安装船instrument unit 测量装置instruments 仪器insulating properties 绝热性质Insulation foam 隔热泡沫Insulation Foam 保温泡沫insulation layer 隔热层 Insulation resistance 绝缘电阻Integral Valves 集成阀Integration Test 完整性试验interaction model 相互作用模型interface area 接口区interface flange 接口法兰INTERFACE REQUIREMENT 接口要求interface with Xmas tree flanges 与采油树法兰的接口 interfaces 接口interfaces 接口internal carcass 内部架构internal corrosion 内部腐蚀internal diameter 内径internal pressure 内压Internal pressure containment 内压限制Internal Profile 内剖面Internal Profile Datum 内剖面基准internal sealing profile 内部密封剖面internal service pressure 内部工作压力internal temperature 内部温度internal tree cap 内部采油树帽Internal welding 内部焊接International Electrotechnical Commission 国际电工委员会Intervention 干预intervention 干预INTERVENTION PHILOSOPHY 干预原理Intervention System 干预系统intervention task 干预任务isolation test tool 绝缘试验工具isolation valve 隔离阀J lay ramp J型敷管滑道J Lay semi-submersible J型铺管半潜式平台J-Lay J型铺管J-Lay method J型铺管法junction 连接junction box 接线盒junction box 接线盒junction plate 连接板keel joint 龙骨接头Key issues 关键问题Kvaerner integrated service umbilical Kvaerner综合功能脐带管Kvaerner umbilical Kvaerner脐带管 landing shoulder 坐放台肩landing string system 坐放式管柱系统 large diameter 大直径large diameter 大直径Latch Mechanism 锁紧机构Latching mechanism 锁紧机构lateral loads 侧向荷载Lay ramp 敷管滑道laying parameters 铺管参数Lazy S 低弯度S型Lazy Wave 低弯度波形Lazy Wave 低弯度波形Lazy wave 低弯度波形Leading Tug 首拖船leak path 渗漏通道level indicator 液面指示器life cycle cost 寿命周期成本Life Cycle Costing 寿命周期成本Life Cycle Costing 寿命周期成本（LCC） Line Insulation Monitor 管道保温监控 line pipe 输送管Linear pullin winch 直线式引入绞车Linear Variable Differential Transformers (LVDT) 线性差动变压器（LVDT）linear winch 直线状绞车liner material 内衬材料liner tube 衬管liner tube 衬管Load ring 承载环load transfer 载荷转移load transfer 载荷转移local buckling criteria 局部折皱标准local control 本地控制器local panel control 本地面板控制盘Lock ring 锁环locking mechanism 锁定机构long beam 长臂long term 长期longitudinal seam 纵向缝longitudinal seam welding 纵向缝焊接low-alloy carbon-steel 低合金碳钢Lower Marine Riser Package 下部海洋隔水管插件（LMRP）Lower tool joint 下部工具接头major component 主要组件 major subsea components 主要海底组件male hub 公卡箍Man Machine Interface 人机接口management system 管理系统Management System 管理系统Mandrel 工作筒manipulator 机械手manipulator arm 操作手臂manipulator arm 机械手臂manipulator arms 机械手臂manipulators 机械手manipulators 机械手manual valves 手动阀manufacturer 制造商marginal field 边际油田Marine Drilling Riser 海洋钻井隔水管marine environment 海洋环境marine growth 海生物聚集marine riser 海洋隔水管Master Control Station 主控台mechanical properties 机械性能Mechanised Pulsed Gas Metal Arc Welding 机械脉冲气体保护金属极电弧焊Medium size flowline 中等尺寸出油管线Melting steel 熔融钢水messenger line 引缆metal to metal seals 金属对金属密封metal tube 金属管Metallic Materials 金属材料metallic sealing materials 金属密封材料Module Replacement Tool (MRT) 模块更换工具（MRT） monitoring system 监控系统Mono Bore Tree 单筒采油树moon pool 月池mooring line 系泊绳Mounting Base 安装基座Mudline Conversion System 泥线转换系统mudline suspension system 泥线悬挂系统Mudline Tree 泥线采油树Mudline Wellhead 泥线井口Multi Mode Running Tool (MMRT) 多模式下送工具（MMRT）multi-phase flow meters 多相流量计multiphase flows 多相流体Multiple load shoulder profile 多载荷台肩剖面 National Aerospace Standard 国家宇航标准natural period 固有周期navigation system 导航系统neutrally buoyant 中和浮力normal operating 正常操作normal operation 正常操作North Sea 北海offshore hydrocarbon pipeline 海上油气管道offshore installation 海上安装Offshore Installations 海上设备offshore pipeline 海洋管道offshore production platform 海上生产平台offshore production platform piping system 海上生产平台管道系统Offshore Technology Conference 海洋技术会议Oil pipeline transportation systems 石油管道运输系统 oil/gas production rate 油/气生产速度open-hearth steelmaking 平炉炼钢operating conditions 作业条件operating cost 运营成本operating cost 运营成本operating pressure 操作压力operating temperature 操作温度 operation 作业operational temperatures 操作温度 operator skill 操作者技能operators 操作者optical fibre 光纤optical fibres 光纤orbital welding 轨道焊接Orientation device 定向仪orientation system 定向系统O-Ring seals O环密封圈O-rings seals O环密封圈outboard hub 外侧轮毂outer pipe 外管outer sheath 外部护套outer sheath 外部护套outer sheath 外部护套outer surface 外表面outer thermoplastic sheath 热塑外部护套 overall length 总长overall System 整个系统Overboard chute 船外下降溜槽 overboarding chute 船外下降溜槽 override functions 优先功能pack off retrieval tool 封隔收回工具 Packoff 封隔Pack-Off 封隔Pack-Off Assembly 封隔总成paraffin deposits 结蜡 parallelepipedic billets 立方坯板料 parking position 停放位置partial pressure 分压performance verification 性能验证 permanent guide base 永久导向基座 Piercing of billets 坯板料穿孔Pig Detection 清管器检测Pig Detector 清管器检测器pig launcher 清管器发送筒pig receiver 清管器接收筒pilot valves 先导阀pin connection 销连接pin connector 销连接器PIPE DIAMETER 管道直径Pipe dimensions 管道尺寸Pipe expansion calculations 管道膨胀计算 pipe in pipe system 管中管系统Pipe inside diameter 管道内径pipe joints 管接头pipe joints 管接头pipe layer dimensions 管层尺寸pipe material 管道材料pipe outside diameter 管道外径pipe section 管道截面Pipe storage Reel 存管卷筒pipe strings 管柱pipe structure 管道结构pipe structure 管道结构pipe system 管道系统pipe wall 管壁Pipe wall thickness 管道壁厚Pipe-in-pipe system 管中管系统pipelay vessel 铺管船pipeline 管道pipeline 管道Pipeline bundle system 管束系统pipeline burial 管道埋设 pipeline design 管道设计Pipeline Design Method 管道设计方法Pipeline End Manifold 管道末端管汇Pipeline end manifold (PLEM) 管道末端管汇（PLEM） Pipeline end terminations 管道端部终端设备pipeline systems 管道系统Pipeline Valve 管道阀piping system 管道系统plastic deformation 塑性变形plastic deformation 塑性变形Poisson coefficient 泊松系数Polyurethane Foam 聚氨酯泡沫Polyvinylidene Fluoride 聚偏氟乙烯position indicators 位置指示器Position Reference System 定位参考系统positioning system 定位系统Positive mechanical lockdown mechanism 正向机械锁定机构post-weld heat treatment 焊后热处理power cable 电缆power cables 电源电缆power channel 电力通道power management 电源管理 power source 电源power source 电源power supplies 电力供应 Power Supply 电源power supply 电源Power Supply 电源Power System 动力系统 pressure balance 压力平衡 pressure balanced 压力平衡 pressure drop 压降Pressure Drop 压降pressure drops 压降pressure gauges 压力表 pressure integrity 压力完整性 pressure monitoring 压力监测 Pressure Sensor 压力传感器 pressure test 压力测试 Pressure Vessel 压力容器 pressure-drop 压降primary pressure 原始压力 Product Flow 产品流动 product leaflets 产品说明书production and annulus master valve 生产和环空总阀 production bore 生产井筒production casing 生产套管production control system 生产控制系统Production Deck 生产甲板production facilities 生产设施production flow rate 生产流量production flowline 生产出油管线production flowline 生产出油管线production flowline system 生产出油管线系统 production fluids 生产流体production gathering 生产集输Production line 生产管线production lines 生产管线Production Master Valve 采油主阀production mode 生产模式production phase 生产阶段production platform 生产平台production rate 采油速度production rates 采油速度Production Riser 生产隔水管production riser 生产隔水管production riser 生产隔水管production risers 生产隔水管Production String 生产管柱Production System 生产系统production system 生产系统Production Template 采油基盘production tree 采油树production tubing 生产油管Project Management 项目管理Project Manager 项目经理project specification 项目规范propagation buckling 延伸折皱propagation pressure 延伸压力propulsion system 推进系统protection cap 保护帽protective structure 防护结构pull force 拉力pull in cable 牵引线缆Pull in winch 牵引绞车pull-in and connection tool 牵引和连接工具 pull-in cable 牵引线缆 pull-in head 拉入头pull-in operation 引入作业pull-in winch 牵引绞车pull-in/connection method 牵引/连接法 Pump Down System 泵送系统pump systems 泵系统qualification 资质Qualification 资质qualification test 合格性测试Quality Assurance 质量保证quality control 质量控制Quality Plan 质量计划Quality System 质量体系Quenching 淬火Quick Connect 快速连接radial forces 径向力reaction loads 反作用载荷real time 实时Reel-Lay 卷管式铺管法Reference Book 参考手册reliability analysis 可靠性分析relief valves 安全阀removable guide posts 活动导向柱reservoir 油藏reservoir 油藏reservoir 油藏reservoir 油藏reservoir pressure 储集层压力residual axial tension 残余轴向拉力 residual strains 残余应变resin binder 树脂粘合剂resistance factor 阻力系数Response time 响应时间Retrieval Tool 收回工具return line 回油管线return line 回油管线return lines 回油管线return tank 回油罐rigid line 刚性管道rigid pipe 刚性管道Rigid Pipe 刚性管rigid pipeline 刚性管道rigid production riser 刚性生产隔水管rigid reeled gas line 刚性卷筒式天然气管道 rigid steel pipe 刚性钢管rigid steel riser 刚性钢质隔水管 ring grooves 环形槽riser 隔水管riser base 隔水管基座riser connector 隔水管连接器riser joint 隔水管接头Riser joints 隔水管单根Riser Pressure 隔水管压力riser system 隔水管系统riser tension 隔水管张力riser tensioner 隔水管张紧器 rolling process 轧制工艺rotary table 转盘ROV 水下机器人（ROV）ROV 水下机器人ROV 水下机器人ROV AND TOOLS 水下机器人和潜水工具 ROV control cabin ROV控制舱ROV deck equipment ROV甲板设备 ROV interface ROV接口ROV intervention ROV修井ROV locking interface ROV锁紧接口ROV manufacturers and subsea contractor ROV制造商和水下承包商ROV panels ROV面板ROV system ROV系统ROV vehicles ROV装置ROVs and Tools 水下机器人和潜水工具running sequence 送入顺序running tool 下入工具running tool 下入工具running tools 下入工具Safe Area 安全区safety factor 安全系数Safety Valve 安全阀safety valve control 安全阀控制Sand Detector 测砂器sand monitor 测砂器sand monitoring 防砂监控Sand Monitors 测砂器Satellite tree 卫星采油树satellite well 卫星井saturation diving 饱和潜水 scan cycle time 扫描周期 scan time 扫描时间sea bed 海床sea bed 海床sea bottom 海底sea bottom 海底sea level 海平面Sea level 海平面sea state 海况sea states 海况sea surface level 海面sea water 海水sea-bed 海底sea-bed level 海底水位 seafloor wellhead 海底井口 Seal area 密封区seal assembly 密封总成 Seal Elements 密封元件 SEAL Engineering SEAL工程 seal material 密封材料 Seal plate 密封板seal pocket 密封腔seal surfaces 密封表面Sealines 海下管线sealing system 密封系统seam welding process 管缝焊接工艺 seamless pipe 无缝管seamless tube 无缝钢管sea-states 海况seawater tolerance 耐海水 Seaway Condor Seaway Condor selector valve 选择阀 semiconductor device 半导体装置 sensing element 传感元件sensing pins 感应针sensor systems 传感器系统serial number 序列号service life 使用寿命service line 维修管线Service line 维修管线seven-function 七功能seven-function 七功能seven-function 七功能severe weather 恶劣天气 shallow water 浅水shear pins 剪切销钉sheave package 滑轮组件side valve tree 旁阀采油树Signal Pair 信号线对signal transmission line 信号传输线silicate microspheres 硅酸盐微球体Single Bore Tree 单筒采油树Skin Effect Current Tracing 集肤电伴热sled piping 滑车管道sleeve pipe 套管soft soil 软土soil conditions 土壤条件solenoid valve 电磁阀Span calculations 跨度计算spare parts 备件special tools 专用工具specific project 指定项目Spirally-oriented seam welded pipe 螺旋焊缝管 splash zone 飞溅区splash zones 飞溅区Split lock ring 开口锁环Spool Piece 短管Spool tree 四通采油树spooling 缠绕spooling system 缠卷系统spray cooling 喷淋冷却法stab plate 插板stainless steel 不锈钢stainless steel strips 不锈钢带static analysis method 静态分析法 steel armoured pipe 钢质铠装管道steel catenary riser 钢质悬链线隔水管 Steel Flying Lead 钢引线steel jacket pipe 钢质夹套管steel pipe 钢管steel riser 钢质隔水管steel tube umbilical 钢管脐带管steel tube umbilical 钢管脐带管steel tube umbilical 钢管脐带管 Steelmaking process 炼钢工艺Steep S-Lay 陡S型铺管法Steep S-Lay vessel 陡S型铺管船Steep Wave 高弯度波形 Steep Wave 高弯度波形Steep wave 高弯度波形Steep wave 高弯度波状Stepwise Cracking 阶式断裂storage reel 存储盘架storage reel 存储盘架straight line 直线strength members 强度元件Stress Corrosion Cracking 应力腐蚀开裂 strong currents 强电流strong seawater currents 海水强流 Submarine pipeline code 海底管道规范 submarine pipeline system 海底管道系统 Submerged Arc Weld 埋弧焊Submerged arc welded pipe 埋弧焊管 submerged weight of the pipeline 管道浮重 submerged weight of the soil 土壤浮重 submerged-arc welded 埋弧焊submerged-arc welded seam 埋弧焊缝subsea blowout preventer 水下防喷器subsea christmas tree 水下采油树Subsea Christmas Tree System 水下采油树系统Subsea cluster manifold 水下丛式管汇Subsea cluster well system 水下丛式井系统subsea contractor 水下承包商Subsea Control Module 海底控制模块subsea control module mounting base 海底控制模块安装基座（SCMMB）Subsea Control Module Running Tool 海底控制模块下入工具Subsea Control Systems 水下控制系统subsea drilling system 水下钻井系统Subsea Electronics Module 水下电子装置模块subsea field 海底油气田subsea intervention tree 水下修井采油树subsea manifold 水下管汇Subsea Production Control System 海底生产控制系统 SUBSEA PRODUCTION EQUIPMENT 海底采油设备Subsea Production Manifold 海底采油管汇Subsea Production System 海底生产系统Subsea Production Template 海底生产基盘subsea system 水下系统Subsea tree single-piece spool body construction 水下采油树单件四通本体结构 Subsea wellhead 海底井口装置subsea wellheads 水下井口Subsurface Safety Valve 水下安全阀Suction Pile 吸力桩Suction Piles 吸力桩Sulphide Stress Corrosion Cracking 硫化物应力腐蚀开裂 super duplex 超双相super-duplex 超双相Supply Tank 供应罐supply voltage 电源电压supply voltage 电源电压support frame 支撑框架surface area 表面积surface BOP 地面防喷器surface casing string 表层套管柱Surface Conductor 地面导管Surface Controlled Sub-Surface Safety Valve 地面控制水下安全阀surface production processing facilities 地面生产处理设施Surface Safety Valve 地面安全阀surface support vessel 水面供应船surface tree 地面采油树Surface Tree 地面采油树surface wellhead 地面井口survey vessel 测量船swab valve 抽汲阀syntactic foam 复合泡沫syntactic foam 复合泡沫Tag Number 标号target area 目标区域 temperature sensor 温度传感器 Temporary Guidebase 临时导向基座 tensile armours 抗拉铠装tensile strength 拉伸强度 tension capacity 张力大小 Tension Leg Platform 张力脚平台 tension leg platforms 张力腿平台 tension load 张力载荷tension loads 拉伸载荷terminal head 终端头termination 终端termination 终端termination point 终端点 termination unit 终端装置test cap 测试帽Test Electrical Power Unit 试验电源装置test method 测试方法test pressures 测试压力Test Tool 试验工具Teta profile T形剖面Teta spiral T形螺旋层thermal expansion 热膨胀thermal expansion coefficient 热膨胀系数thermal insulation 隔热thermal insulation 隔热thermal insulation 隔热thermal insulation and Aluminium-sacrificial anode system 隔热和牺牲铝阳极系统thermal insulation material 隔热材料thermal insulation system 隔热系统thermal insulation system 隔热系统thermal shrink-fit method 热收缩-配合法Thermo-hydraulic fit method 热-液压配合法Thermo-Mechanical Controlled Processing 热机械控制工艺。

船舶与海洋工程专业专业英语词汇船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船)ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布) iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。

IMO(Intergovernmental Maritime Organization)国际海事组织IMCO(Intergovernmental Maritime Consultative Organization)国际海事质询组织International Towing Tank Conference (ITTC) 国际船模试验水池会议International Association of Classification Society (IACS) 国际船级社协会ABS(American Bureau of Shipping) 美国船级社BV(Bureau Veritas) 法国船级社Lloyd's Register of shipping 英国劳埃德船级社RINA(Registo Italiano Navade) 意大利船级社Load Line Convention 载重线公约Lloyd's Rules 劳埃德规范Register （船舶）登录簿，船名录Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船Supervision of the Society's surveyor 船级社验船师的监造书Merchant Shipbuilding Return 商船建造统计表BSRA 英国船舶研究协会HMS 英国皇家海军舰艇CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程CAPP(computer -aided process planning) 计算机辅助施工计划制定IAGG(interactive computer graphics) 交互式计算机图像技术a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar/plate 角钢angle of attack 攻角angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船base line 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板爱beam knee 横梁肘板bearing 轴承bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli's law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船，双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow's nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量)design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力爱dredge 挖泥船drift 漂移，偏航drilling rig 钻架drill ship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架frame spacing 肋骨间距freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁爱gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞gross ton 长吨（1.016公吨，short for GT）group technology 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖（板）hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船living and utility spaces 居住与公用舱室load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向棱形系数longitudinal strength 总纵强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距ipitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架爱propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器9 rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder horn 挂舵臂rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数section 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shaft coupling 联轴节shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft/forward 艉/艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 总剖线，纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway/slipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板sloping bottom plate of topside tank 顶边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板爱stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面预处理与喷涂surge 纵荡sway 横荡yaw 首摇surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tender 交通小艇timber carrier 木材运输船tugboat 拖船tee T型构件，三通管tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器tip of a blade 桨叶叶梢toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率LCC 大型原油轮ULCC 超级大型原油轮VLCC 巨型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性V oith-Schneider propeller 外摆线直翼式推进器vortex 梢涡v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁--。