TDK联机电脑使用必备说明书(doc 19页)

• 基于现有TDK-Lambda 产品，增加外围线路或机械结构设计来满足特定需求，提供优化的整体电源解决方案。

• 增值电源方案同样保持标准品所拥有的可靠性。

• 例如：增加机箱机架、特别的线束、开关、保险丝、风扇或散热器、额外的功能、模块电源的评估板。

• 根据客户的需求完全定制。

• 基于现有的技术平台或新的技术。

• 例如：多路输出、高功率密度、先进技术、严酷的温度范围、超低的噪声等。

医疗轨道交通半导体机器人科研测试与测量智能电网楼宇定制品增值服务标准AC-DC 电源标准DC-DC 电源CVCC 可编程电源电子负载行业应用图标电源+安全使用说明使用本公司产品前，请注意下示所有的警告和提醒。

不正确的使用可能会导致触电，产品损坏或者火灾的危险。

警告•请勿改装，拆解或取下产品外壳。

否则，可能会引起触电、烫伤或火灾。

本公司不承担相应的责任。

•产品运行时，某些内部元件会产生高压和高温。

如果触摸这些内部元件，可能会引起触电或烫伤。

•产品运行时，手和脸请勿靠近。

否则，可能会造成意外伤害。

提醒•使用本公司产品前，请仔细阅读并确认产品目录及使用说明书的内容。

•在进行输入输出接线时，请切断输入电源。

•输入电压、输出电流、输出功率、环境温度和环境湿度都应符合规定范围，否则产品可能会损坏。

•为了安全与降低噪音，请把本产品的机壳地与设备地连接在一起。

否则，可能会有触电的危险。

•如果产品内部保险丝开路，请不要自行更换保险丝，因为可能有其它元件损坏。

请联系本公司的维修中心。

•应当定期更换使用寿命有限的元件（例如电解电容器、内部风扇）。

请根据使用环境确定合适的检修期。

•本公司竭尽全力提高产品的质量和可靠性。

但是，产品也可能偶尔会出现故障或异常。

因此，在需要高可靠性的设备（例如核反应控制、航空航天、生命保障、医疗、交通控制等设备）中使用本公司产品时，应确保产品失效安全的功能。

•如果将产品用于存在水份、湿气、粉尘、强电磁场、腐蚀性（包括硫化等）气体或者有外来导电物质进入的环境中，可能会导致产品内部元件故障。

TDK联机电脑使用说明书一、使用准备1、电脑主机、显示器电源要求接:220V 50/60 Hz；2、将数据线9针口连接在PC COM1接口，25针接TDK机器主控箱外接口，外接口如图：机器接口位置3、打开电脑主机及显示器。

※注意：数据线连接好后，再开电脑主机，COM1串口和TDK机器外接口不支持热插拔！否则有烧坏接口的情况发生！※4、将TDK设备系统OPTIONAL PARAMETER WORD N0.2=8 N0.21=1 N0.22=0。

OPTIONAL PARAMETER BIT N0.1=01010011 N0.2=00000001。

a、OPTIONAL PARAMETER WORD设定方法：按操作面板上MODEL SELECT之SYSTEM DATA 灯亮，按F4（ITEM）直至出现OPTIONAL PARAMETER WORD画面，把光标移至N0.2后的数字上，按F1（SET）在键盘上按8然后按，N0.2设定完成。

使用键翻页，找到N0.21、N0.22所在页，把光标移至N0.21后的数字上，按F1（SET）在键盘上按1然后按，把光标移至N0.22后的数字上，按F1（SET）在键盘上按0然后按。

b、OPTIONAL PARAMETER BIT设定方法：按操作面板上MODEL SELECT之SYSTEM DATA 灯亮，按F4（ITEM）直至出现OPTIONAL PARAMETER BIT画面，把光标移至N0.1后的数字上，按F1（SET）在键盘上按01010011然后按，再把光标移至N0.2后的数字上，按F1（SET）在键盘上按00000001然后按。

机器设定完成。

二、电脑操作1、打开电脑出现c:\＞提示，c:\＞TDK 回车（Enter）出现如下画面：2、按任意键出现出现如下主菜单画面：菜单说明：（F1）DOWN LOAD 程序从电脑发送到机器(F2) UP LOAD 程序从机器保存到电脑（F3）DATA EDIT 程序编辑（F4）CONFIGURATION 连接软件系统设定（F5）M/C MODEL CHANGE 机器型号更换（F6）DATA AND PRINTER 数据文件列表打印（ESC）END OFF SYSTEM 退出三、程序从电脑发送到机器1、电脑操作，按（F1）DOWN LOAD出现画面：a、写入程序所在路径，如下画面：b、回车（Enter），出现如下画面，打开文件所在文件夹：c、输入要传送到机器的程序名, 程序名后缀“.VC5”必须写上，如下画面：d、回车（Enter）出现如下画面：e、输入传送到机器文件名，文件名名后缀“.VC5”必须写上，如下画面：注意：※1、在输入程序名和文件名时后缀的.VC5必须写全否则机器可能无法识别程序，可能造成无法传输的情况发生！※※2、PROGRAM NAME: 与:输入的名字后缀必须一样，否则可能造成无法传输的情况发生！※f、回车（Enter）出现如下画面：2、电脑操作完成，接下来还要进行TDK设备上的操作。

May 2023B U Z Z E R SCaution插针端子型SDC1610SDC1614电磁蜂鸣器带电路型插针端子SDC 系列REACHSVHC-FreeRoH S电磁蜂鸣器带电路型插针端子产品阵容SDC系列的概要类型型号外形尺寸特点额定电压外径(mm)高度(mm)端子间距(mm)音压dB(A)/10cm 频率(Hz)Eo-p (V)SDC1610SDC1610M5-01ø16105852400±20%5SDC1610MT -01ø16105852400±20%12SDC1614SDC1614L5-01ø16145851900±20%5SDC1614LT -01ø16145851900±20%12RoHS 指令对应产品指令对应产品：详细内容查看这里。

https:///info/zh/environment/rohs/index.htmlSDC1610MT-01 /ø16mm特点用途电脑，办公设备，家电产品等。

形状与尺寸特性· 规格* 驱动条件：额定电压- 电流特性型号SDC1610M5-01SDC1610MT-01额定电压Edc(V)512工作电压Edc(V) 4 to 88 to 16频率(Hz)*2400±20%2400±20%音压(dB(A)/10cm)min.*8585平均电流最大(mA)*3025端子结构插针端子插针端子使用温度范围–10 to +70°C 保存温度范围–20 to +80°CSDC1614LT-01 /ø16mm特点1900Hz 的低频振荡型产品，音质柔和。

用途电脑，办公自动化设备，医疗设备，办公设备（电子打火机， ECR 等），家电产品（微波炉，电饭锅等）形状与尺寸特性· 规格* 驱动条件：额定电压- 电流特性型号SDC1614L5-01SDC1614LT-01额定电压Edc(V)512工作电压Edc(V) 4 to 88 to 16频率(Hz)*1900±20%1900±20%音压(dB(A)/10cm)min.*8585平均电流最大(mA)*3025端子结构插针端子插针端子使用温度范围–10 to +70°C 保存温度范围–20 to +80°C使用注意事项在使用本产品前，请务必随附采购规格书。

TDK-LambdaDC-DCTrusted • Innovative • ReliableTDK 株式会社总部位于日本东京，是一家为智能社会提供电子解决方案的全球领先的电子公司。

TDK 建立在精通材料科学的基础上，始终不移地处于科技发展的最前沿并以“科技，吸引未来”，迎接社会的变革。

公司成立于1935年，主营铁氧体，是一种用于电子和磁性产品的关键材料。

TDK 全面 和创新驱动的产品组合包括无源元件，如陶瓷电容器、铝电解电容器、薄膜电容器、磁性产品、高频元件、压电和保护器件、以及传感器和传感器系 统（如：温度和压力、磁性和MEMS 传感器）。

此外，TDK 还提供电源和 能源装置、磁头等产品。

产品品牌包括T D K 、爱普科斯(E P C O S )、 InvenSense 、Micronas 、Tronics 以及TDK-Lambda 。

TDK 重点开展如汽车、工业和消费电子、以及信息和通信技术市场领域。

公司在亚洲、欧洲、北美洲和南美洲拥有设计、制造和销售办事处网络。

在2020财年，TDK 的销售总额为125亿美元，全球雇员约为107,000人。

TDK-Lambda 是一家向全球提供值得信赖，创新的高可靠工业电源解决方案的行业领导公司。

TDK Lambda 公司在中国、日本、欧洲、美国和东南亚的全球5大区域均拥有研发、制造、销售，售后服务和应用技术支持等完整的体制，随时随地快速地对应客户的各种各样需求。

关于TDK 公司关于TDK-Lambda 公司COMPANYPROFILE公司简介长沙办事处武汉销售部成都销售部西安办事处北京销售部大连销售部杨梅销售部深圳销售部香港销售部青岛办事处南京办事处杭州办事处广州办事处无锡总部、销售上海 R&D 、市场部、销售部TDK-Lambda 中国支持网络Trusted•Innovative•Reliable目录电源模块●散热设计和安装方法 (1)PFE500F, 1000FA, 1200FA应用手册 (20)PFE300SA, 500SA应用手册 (33)PFE700SA应用手册 (41)PH-A应用手册 (48)PAF600F280, 750C280应用手册 (64)CPF-F280应用手册 (71)CN-A应用手册 (83)HQA应用手册 (93)GQA应用手册 (95)PF-A应用手册 (97)PAF-F24, -48应用手册 (108)PAH应用手册 (118)CCG应用手册 (129)CC-E应用手册 (141)i3A应用手册 (146)i6A应用手册 (148)i7C应用手册 (151)CHVM应用手册 (154)附录1●推荐连接线路图 (160)附录2●快速评估板 (164)附录3●CN-A系列打嗝保护方案 (165)1应用实例说明* 请注意本文所述的内容可能在未经事先通知的情况下发生更改，敬请谅解。

前面板上的控制器和指示器：
后面板拨码开关SW1（我们使用时1和9 UP）
SAF和AU7模式切换：
长按OUT键可以让电源在安全启动模式（SAF）和自动重启模式（AU7）之间切换，如果显示SAF时松开OUT，则为SAF模式；
安全启动模式：当电源处于安全启动模式下，使能/禁用故障解除后，可通过按下OUT按钮或发送“OUT 1”串行通信命令来恢复输出；
自动重启模式：使能/禁用故障解除后，输出将自动返回到 ON 状态
在SAF模式下，只能自动触发输出一次；而在AU7模式下，则不限次数；从SAF模式切换至AU7模式后，需手动按一下OUT键以后，电源才能正常工作。

电压源模式和电流源模式的切换：
按下PREW设置电流电压值，如10V，10A；如果负载为0.5欧姆，10V和10A 先到10A，则电源处于电流源模式；同样10V和10A的参数，如果负载大于1欧姆，则10V先到，此时电源处于电压源模式。

J1为25针插头，9和22引脚控制电压：
工控机—W1电路板—A1板卡—J1的9和22针（控制电压的信号）
J1的1和14脚与K21的常开触点连接，为ENABLE信号。

Dimensions: [mm]Scale - 4:174404084102BC74404084102T e m p e r a t u r eT pT L74404084102Cautions and Warnings:The following conditions apply to all goods within the product series of WE-LQS of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChrB.001.0042022-08-25DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404084102SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChrB.001.0042022-08-25DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404084102SIZE/TYPE BUSINESS UNIT STATUS PAGE。

Dimensions: [mm]Scale - 7:1Product Marking:Marking330 (Inductance Code)7440404133074404041330BC74404041330T e m p e r a t u r eT pT L74404041330Cautions and Warnings:The following conditions apply to all goods within the product series of WE-LQS of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChriB001.0042023-02-28DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404041330SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODChriB001.0042023-02-28DIN ISO 2768-1mDESCRIPTIONWE-LQS SMT Semi-ShieldedPower Inductor ORDER CODE74404041330SIZE/TYPE BUSINESS UNIT STATUS PAGE。

Virtual Control Panel 安装和应用指南版本记录日期版本发行2022 年 3 月H - 初始版本目录1.简介 (1)一般信息 (1)简介 (1)通信接口 (1)软件要求 (1)最低硬件要求 (2)兼容设备 (2)2.首次安装 (3)3.修改软件包 (15)添加和删除软件包 (15)修复（重新安装）所有软件包 (18)升级软件包 (19)4.卸载 (22)卸载所有软件包 (22)取消安装 (26)5.VIRTUAL CONTROL PANEL 功能 (27)6.系列特定功能 (29)7.基本功能 (30)初始设置 (30)基本控制和监视 (34)终端 (35)波形生成器 (36)保护 (39)模拟量编程和数字信号 (40)全局命令 (41)太阳能电池阵列模拟器 (42)其他 (44)8.多电源模式 (46)功能 (46)连接说明 (47)9.高级功能 (50)序列发生器 (50)斜率控制 (55)内阻 (56)恒功率模式 (57)10.故障排除 (58)E THER CAT设备不显示 (58).NET F RAMEWORK 更新错误消息 (59)本页空白。

1.简介一般信息文档（包括本用户指南）如有更改，恕不另行通知。

最新文档请在TDK-Lambda 的技术数据网页进行下载，网页链接如下：/software简介Virtual Control Panel (VCP) 是一个图形用户界面，允许用户使用单个 PC 应用程序轻松地远程控制所有TDK-Lambda可编程电源。

使用软件安装工具 Package Manager 可以安装该应用程序。

该工具负责安装和更新用于TDK-Lambda可编程电源的驱动程序和工具。

该工具包含多个软件包，可简化在 PC 上安装这些软件包的过程。

通信接口Virtual Control Panel 可通过以下多种接口与电源通信：•RS-232/RS-485•USB•以太网 (LAN)•IEEE-488 (GPIB)•MODBUS-TCP•EtherCAT软件要求•Microsoft Windows 10（64 位）•.NET Framework 4.8（64 位）注1. VCP 正式兼容Windows 10（64 位）。

Dimensions: [mm]74477792227447779222BC7447779222T e m p e r a t u r eT pT L7447779222Cautions and Warnings:The following conditions apply to all goods within the product series of WE-PD of Würth Elektronik eiSos GmbH & Co. KG:General:•This electronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Electronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged.•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.•Strong forces which may affect the coplanarity of the components’ electrical connection with the PCB (i.e. pins), can damage the part, resulting in avoid of the warranty.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the wire insulation, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the wire due to its small diameter. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material may shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the core. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Electronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the components to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current will void the warranty.•Applying currents with audio-frequency signals may result in audible noise due to the magnetostrictive material properties.•The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient temperature and temperature rise of the component.•Temperature rise is highly dependent on many factors including PCB land pattern, trace size, and proximity to other components.Therefore, temperature rise should be verified in application conditions.The operating temperature of the component shall not exceed the maximum temperature specified.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODALa011.0002023-05-30DIN ISO 2768-1mDESCRIPTIONWE-PD Robust SMT ShieldedPower Inductor ORDER CODE7447779222SIZE/TYPE BUSINESS UNIT STATUS PAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODALa011.0002023-05-30DIN ISO 2768-1mDESCRIPTIONWE-PD Robust SMT ShieldedPower Inductor ORDER CODE7447779222SIZE/TYPE BUSINESS UNIT STATUS PAGE。