Banner Slider 用户手册说明书

NISSAN蓝鸟汽车说明书

-1- 前 言

一、车辆使用过程中的重要注意事项

承蒙您选购本公司的汽车，谨表谢意。

欢迎您加入驾驶本公司车辆的行列。

我们确信，您一定会对自己的选择感到满意。

本车辆是集中了东风汽车有限公司最先进的技术而制造的，我们为了使各位驾驶员更好地了解本公司车辆的正确使用方法及保养方法，同时为了既能安全、经济驾驶又能延长车辆的使用寿命，在各车辆上配各了汇集使用注意事项的车辆使用说明手册。

请您在驾驶之前。务必阅读本车辆的使用说明手册，熟悉车辆的正确使用方法。如果对本车辆的装置及其操作方法、车辆的维修保养等有不明之处时 请您向东风NISSAN专营店询问，他们一定会高兴地为您服务。

1、关于起动发动机

1）确实拉紧驻车制动器。确认变速杆是否在空档的位置（自动变速器的变速杆放到P或N的位置）。为了减少发动机转动时的阻力，把离合器踩到底后再起动发动机。

2）为延长起动机和蓄电池的寿命，起动机的连续起动时间请不要超过10秒钟。需要再次起动时把点火钥匙转回OFF的位置，等待10秒钟以后再起动。

3）冬季使用车辆时必须预热发动机，当水温表的指针开始移动时，方可驾驶。

NISSAN蓝鸟汽车说明书

-2- 2、关于经济驾驶方法

1）离合器的连接要缓慢，车辆起步要平稳。在发动机高转速的状态下起步，会使燃料的消耗量增加，离合器的寿命也会缩短。

2）绝对禁止二档起步。二档起步会给发动机、离合器、变速器、齿轮等带来不必要的负荷而加速损坏。

3）为了节省燃料和延长发动机的使用寿命，一档起步以后，请务必按照说明手册所推荐的车速来进行换挡。比如四档，车速必须在50公里以上使用；低速（如30公里）时，若过早换到高速档，发动机会发生爆震。运行中发生爆震，除了使发动机的动力下降以外，燃料消耗量也会极端恶化；另外，严重爆震会成为发生汽缸密封垫冲坏、曲轴瓦烧接等重大故障的原因；当然，在低速档运转车辆在推荐速度以上行驶，这也会成为发动机超速运转而造成轴瓦、活塞环烧接等的原因，且在这种情况下燃料消耗量也必然会增加。

1

美的展厅信息发布系统

用户手册

二零一一年五月

2

目录

1． 引言.................................................................................................................................................... 1

1.1编写目的 ........................................................................................................................................ 1

1.2阅读对象 ........................................................................................................................................ 1

2． 软件使用说明 .................................................................................................................................... 2

2.1主界面 ............................................................................................................................................ 2

2.1.1用户登录 .................................................................................................................................. 2

Series MXFø8, ø12, ø16, ø20

20161281020305075100MXF20MXF16MXF12MXF8MXF8MXF12MXF16MXF2016 x 5818.5 x 6821 x 8027 x 92Low Profile Slide Table

Low-profile and compact type, air slide table with the construction of guide and cylinder aligned in parallel.Low-profile and compactness have been achieved with the construction of guide and cylinder aligned in parallel.ModelHeight x Width (mm)Height comparison to MXS

Stronger thread for mounting workHigh rigidityOptional portingReproducibility for mounting and dismountingAuto switch is mountableSlim bodyStandard stroke adjustment

Reproducibility for mounting anddismountingNeat appearanceStroke can be adjusted at each stroke end within 5 mm each end and 10 mm is total.

Insert thread for mounting work.Cross roller guide allows smooth operation without teral and axial piping from 2 directions is possible.Pin holes for positioning on bottom of slide allows precise and accurate mounting of actuator.Body mounting (Body tapped)Auto switch is recessed in the groove to save space.Low-profile has been achieved with the construction of guide and cylinder aligned in parallel.Body mounting (Body tapped)Protecting stopper section with cover realizes neat appearance.

Datasheet

Class 1 and 2 lasers for use with Banner modulated photoelectric receivers.•Self-contained Class 1 or Class 2 modulated visible laser diode emitters permithigher gain than LEDs and extended range in opposed-mode sensing systems•Narrow effective beam provides small-object detection and precise positioncontrol•Bright spot and multiple shapes provide great visual marking of objects•10 V dc to 30 V dc operation•Laser beam enabled by white wire (pin 2)

WARNING: Not To Be Used for Personnel ProtectionNever use this device as a sensing device for personnel protection. Doing so could lead to serious injury ordeath. This device does not include the self-checking redundant circuitry necessary to allow its use inpersonnel safety applications. A sensor failure or malfunction can cause either an energized or de-energizedsensor output condition.Models1Laser ClassLaser Spot ShapeExcess Gain at 15 m (50 ft) 2Typical Beam Size