乙炔气物质安全数据表(MSDS)

MSDS化学品安全数据表化学品名称：甲醛编号： MSDS-08CAS号：50-00-0危险品编号：83012分子式：CH2O;CH2O;HCHO熔点：-92沸点：闪点：85( 30% 工业用溶液相对密度：0.815(-20)溶解度：122外观及性状：无色、拥有刺激性气味 , 含 15% 甲醇中文又名：福尔马林 ; 蚁醛空气中同意极限：美国 TWA：水中同意极限：美国： 41.4 μ g/l 前苏联 MAC：μ g/l ( 生活用水 )禁忌物 / 禁忌：强氧化剂、强碱强酸 , 苯酚、尿素危险性 / 症状：火／爆炸 : 易燃侵入门路 : 吸入 , 食入 , 皮肤及眼睛接触健康危害 : 短时过分裸露刺激和灼伤皮肤、眼睛和粘膜 , 哭泣、恶心、呕吐 ( 呕血 ) 、腹痛、腹泻、呼吸困难、咳嗽、肺炎、肺水肿、敏感者会出现气喘反响。

在心血管瘫痪前可能出现低血压和体温降低 , 及嗜眠、头昏、惊风和昏倒、肾炎、血尿、肝中毒抢救举措：火／爆炸 : 喷水或使用、泡沫灭火剂 ; 若无危险 , 可将容器移出现场 ; 喷水冷却火中容器 , 免得爆炸 , 但容器内勿进水眼接触 : 马上用清水冲刷皮肤接触 : 马上用清水冲刷吸入 : 将患者移至新鲜空气处 , 实行人工呼吸其余 :误服后,就医,让患者大批饮水,使其呕吐(昏倒者例外)防备举措：穿专用防备服 , 戴护目镜 , 戴防毒面具或呼吸器 , 皮肤沾染后 , 马上冲刷 ; 改换并转移被污染的防备器具 ; 装备应急喷淋设施和眼药水 ; 按期检查肺功能储藏：存于密闭容器内 ,置于凉快、通风处;隔热,避氧化剂、碱;禁止烟火泄露办理：切断点火源 , 禁止烟火 ; 不得触摸泄露物 , 安全前提下尽量堵漏 ; 喷水减少泄露物挥发量 ; 禁止容器进水 ; 少许泄露 , 使用砂土或其余不吸附剂汲取至容器内待办理 ; 大批泄露, 围堤办理，运输无需贴标签 , 航空、铁路限量运输。

危险化学品安全技术手册MSDS（化学品清单）制定: 2003-07-01氨俗称：分子式：NH3危险毒害，易燃易爆，强刺激性，避免接触危险性泄漏处理∙毒害∙撤离现场无关人员，切断火源∙具强烈刺激性∙戴呼吸器，穿特定化学防护服∙与空气混合有燃烧爆炸的危险∙切断气源∙与卤素发生剧烈反应∙高浓度泄漏时，喷含盐酸的雾状水∙强力通风储运要求急救∙储存于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与卤素（氟、氯、溴）酸类等分储∙脱离污染环境至空气新鲜处，必要时∙禁止使用易产生火花的工具∙输氧或人工呼吸∙灌装适量，不可超压超量∙就医∙按运输路线行驶，中途勿停∙灭火方法∙雾状水、二氧化碳、泡沫∙切断气源，喷水冷却容器防护措施废弃处理参阅国家和地方法规，用控制焚烧法或分解法处理。

盐酸俗称：分子式：HCl危险强腐蚀性，避免接触金属、氰化物危险性泄漏处理∙具腐蚀性∙撤离现场无关人员∙与金属反应，放出氢气∙戴防毒面具，穿化学防护服∙遇氰化物产生剧毒的气体∙禁止直接喷水∙用砂土、干石灰等混合，收集处理∙大量泄漏，围堤收容处理储运要求急救∙储存于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与碱类、金属粉末、卤素（氟、氯∙脱离污染环境至空气新鲜处∙溴）易（可）燃物等分储∙误服后，喝蛋清或牛奶∙搬运时注意个人防护∙就医∙轻装轻卸，防止破损∙按规定路线运输行驶灭火方法∙∙雾状水、砂土防护措施废弃处理参阅国家和地方法规，处理后排下水道。

生效日期2003-7-1 编号GJ-HF-MSDS-003硫酸俗称：分子式：H2SO4危险强腐蚀性，有害，避免接触易燃物危险性泄漏处理∙强腐蚀性∙撤离现场无关人员∙毒害∙戴面罩，穿化学防护服∙接触易燃物和有机物能引起燃烧∙避免泄漏物接触可燃物∙与活性金属反应，放出氢气∙用砂土、干石灰等混合，收集处理∙大量泄漏，围堤收容处理储运要求急救∙储于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与易（可）燃物、碱类、金属粉末∙脱离污染环境至空气新鲜处∙等分储∙如灼伤，按酸灼伤处理∙搬运时注意个人防护∙误服后，喝蛋清或牛奶∙轻装轻卸，防止破损∙就医∙灭火方法∙砂土，禁止用水防护措施废弃处理参阅国家和地方法规，用纯碱或石化中和后，冲入下水道。

危险化学品安全技术手册MSDS（化学品清单）制定: 2003-07-01氨俗称：分子式：NH3危险毒害，易燃易爆，强刺激性，避免接触危险性泄漏处理∙毒害∙撤离现场无关人员，切断火源∙具强烈刺激性∙戴呼吸器，穿特定化学防护服∙与空气混合有燃烧爆炸的危险∙切断气源∙与卤素发生剧烈反应∙高浓度泄漏时，喷含盐酸的雾状水∙强力通风储运要求急救∙储存于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与卤素（氟、氯、溴）酸类等分储∙脱离污染环境至空气新鲜处，必要时∙禁止使用易产生火花的工具∙输氧或人工呼吸∙灌装适量，不可超压超量∙就医∙按运输路线行驶，中途勿停∙灭火方法∙雾状水、二氧化碳、泡沫∙切断气源，喷水冷却容器防护措施废弃处理参阅国家和地方法规，用控制焚烧法或分解法处理。

盐酸俗称：分子式：HCl危险强腐蚀性，避免接触金属、氰化物危险性泄漏处理∙具腐蚀性∙撤离现场无关人员∙与金属反应，放出氢气∙戴防毒面具，穿化学防护服∙遇氰化物产生剧毒的气体∙禁止直接喷水∙用砂土、干石灰等混合，收集处理∙大量泄漏，围堤收容处理储运要求急救∙储存于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与碱类、金属粉末、卤素（氟、氯∙脱离污染环境至空气新鲜处∙溴）易（可）燃物等分储∙误服后，喝蛋清或牛奶∙搬运时注意个人防护∙就医∙轻装轻卸，防止破损∙按规定路线运输行驶灭火方法∙∙雾状水、砂土防护措施废弃处理参阅国家和地方法规，处理后排下水道。

生效日期2003-7-1 编号GJ-HF-MSDS-003硫酸俗称：分子式：H2SO4危险强腐蚀性，有害，避免接触易燃物危险性泄漏处理∙强腐蚀性∙撤离现场无关人员∙毒害∙戴面罩，穿化学防护服∙接触易燃物和有机物能引起燃烧∙避免泄漏物接触可燃物∙与活性金属反应，放出氢气∙用砂土、干石灰等混合，收集处理∙大量泄漏，围堤收容处理储运要求急救∙储于阴凉、干燥、通风处∙脱去污染衣着，用清水洗污染部位∙应与易（可）燃物、碱类、金属粉末∙脱离污染环境至空气新鲜处∙等分储∙如灼伤，按酸灼伤处理∙搬运时注意个人防护∙误服后，喝蛋清或牛奶∙轻装轻卸，防止破损∙就医∙灭火方法∙砂土，禁止用水防护措施废弃处理参阅国家和地方法规，用纯碱或石化中和后，冲入下水道。

ARALDITE®2011SAFETY DATA SHEETProduct name ARALDITE®2011:1.1Product identifier 1.3Details of the supplier of the safety data sheet e-mail address of person responsible for this SDS:Global_Product_EHS_AdMat@Product description:1.2Relevant identified uses of the substance or mixture and uses advised against Product code:000573301.4Emergency telephone number SupplierTelephone number :EUROPE:+3235751234France ORFILA:+33(0)145425959ASIA:+656336-6011China:+862039377888Australia:1800786152New Zealand:0800767437USA:+1/800/424.93002-Component adhesive system Product use :Supplier :Huntsman Advanced Materials (Europe)BVBAEverslaan 453078Everberg /Belgium Tel.:+41612992041Fax:+41612992040Classification Xi;R36/38R43N;R51/53::Human health hazards Irritating to eyes and skin.May cause sensitisation by skin contact.:Environmental hazardsToxic to aquatic organisms,may cause long-term adverse effects in the aquatic environment.See Section 11for more detailed information on health effects and symptoms.2.1Classification of the substance or mixture Product definition :Working pack (preparation)See Section 16for the full text of the R phrases or H statements declared above.Classification according to Directive 1999/45/EC [DPD]The product is classified as dangerous according to Directive 1999/45/EC and its amendments.2.2Label elementsHazard symbol orsymbols:Irritant,Dangerous for the environmentIndication of danger ::Other hazards which do not result in classificationNot available.Containers to be fitted with child-resistant fasteningsNot applicable.Tactile warning of danger Not applicable.::Special packaging requirements Safety phrasesS2-Keep out of the reach of children.S24-Avoid contact with skin.S29-Do not empty into drains.S37-Wear suitable gloves.S46-If swallowed,seek medical advice immediately and show this container or label.S61-Avoid release to the environment.Refer to special instructions/safety data sheet.R36/38-Irritating to eyes and skin.R43-May cause sensitisation by skin contact.R51/53-Toxic to aquatic organisms,may cause long-term adverse effects in the aquatic environment.Risk phrasesHazardous ingredients:::reaction product:bisphenol A-(epichlorhydrin);epoxy resin (number average molecular weight <700)N(3-dimethylaminopropyl)-1,3-propylenediamine bisphenolF-epoxy resinbisphenol A -epoxy resins,number average MW >700-<11002.3Other hazardsSupplemental label elements:Contains epoxy constituents.See information supplied by the manufacturer.Substance/mixture Working pack (preparation):Occupational exposure limits,if available,are listed in Section8.There are no additional ingredients present which,within the current knowledge of the supplier and in theconcentrations applicable,are classified as hazardous to health or the environment and hence require reporting in this section.[1]Substance classified with a health or environmental hazard [2]Substance with a workplace exposure limit[3]Substance meets the criteria for PBT according to Regulation (EC)No.1907/2006,Annex XIII [4]Substance meets the criteria for vPvB according to Regulation (EC)No.1907/2006,Annex XIII TypeWash out mouth with water.Remove dentures if any.Remove victim to fresh air and keep at rest in a position comfortable for breathing.If material has been swallowed and the exposed person is conscious,give small quantities of water to drink.Stop if the exposed person feels sick as vomiting may be dangerous.Do not induce vomiting unless directed to do so by medical personnel.If vomiting occurs,the head should be kept low so that vomit does not enter the lungs.Get medical attention if adverse health effects persist or are severe.Never give anything bymouth to an unconscious person.If unconscious,place in recovery position and get medical attention immediately.Maintain an open airway.Loosen tight clothing such as a collar,tie,belt or waistband.Skin contactImmediately flush eyes with plenty of water,occasionally lifting the upper and lowereyelids.Check for and remove any contact lenses.Continue to rinse for at least 10minutes.Get medical attention.Flush contaminated skin with plenty of water.Remove contaminated clothing and shoes.Wash contaminated clothing thoroughly with water before removing it,or wear gloves.Continue to rinse for at least 10minutes.Get medical attention.In the event of any complaints or symptoms,avoid further exposure.Wash clothing before reuse.Clean shoes thoroughly before reuse.4.1Description of first aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing.If not breathing,if breathing is irregular or if respiratory arrest occurs,provide artificial respiration or oxygen by trained personnel.It may be dangerous to the personproviding aid to give mouth-to-mouth resuscitation.Get medical attention if adverse health effects persist or are severe.If unconscious,place in recovery position and get medical attention immediately.Maintain an open airway.Loosen tight clothing such as a collar,tie,belt or waistband.In case of inhalation of decompositionproducts in a fire,symptoms may be delayed.The exposed person may need to be kept under medical surveillance for 48hours.IngestionInhalationEye contact ::::Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training.It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.Wash contaminated clothing thoroughly with water before removing it,or wear gloves.4.2Most important symptoms and effects,both acute and delayed Potential acute health effects Inhalation :Exposure to decomposition products may cause a health hazard.Serious effectsmay be delayed following exposure.Irritating to mouth,throat and stomach.:Ingestion Skin contact :Irritating to skin.May cause sensitisation by skin contact.Irritating to eyes.:Eye contactNotes to physician In case of inhalation of decomposition products in a fire,symptoms may be delayed.The exposed person may need to be kept under medical surveillance for 48hours.:Specific treatments Over-exposure signs/symptoms Skin contactIngestionInhalation No specific data.No specific data.Adverse symptoms may include the following:irritation redness:::Eye contact :Adverse symptoms may include the following:irritationwatering redness 4.3Indication of any immediate medical attention and special treatment needed :Symptomatic treatment and supportive therapy as indicated.Following severeexposure the patient should be kept under medical review for at least 48hours.Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire.No action shall be taken involving any personal risk or without suitable training.This material is toxic to aquatic organisms.Fire water contaminated with this material must be contained and prevented from being discharged to any waterway,sewer or drain.Hazardous thermaldecomposition productsHazards from the substance or mixture Decomposition products may include the following materials:carbon dioxide carbon monoxide nitrogen oxideshalogenated compoundsIn a fire or if heated,a pressure increase will occur and the container may burst.Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA)with a full face-piece operated in positive pressure mode.Clothing for fire-fighters (including helmets,protective boots and gloves)conforming to European standard EN 469will provide a basic level of protection for chemical incidents.Special protectiveequipment for fire-fightersUse an extinguishing agent suitable for the surrounding fire.5.1Extinguishing media :::None known.Suitable extinguishing media:Unsuitable extinguishing media:5.2Special hazards arising from the substance or mixture 5.3Advice for firefighters Special precautions for fire-fighters:6.2Environmental precautionsStop leak if without risk.Move containers from spill area.Approach the release from upwind.Prevent entry into sewers,water courses,basements or confined areas.Wash spillages into an effluent treatment plant or proceed as follows.Contain and collect spillage with non-combustible,absorbent material e.g.sand,earth,vermiculite or diatomaceous earth and place in container for disposalaccording to local regulations.Dispose of via a licensed waste disposal contractor.Contaminated absorbent material may pose the same hazard as the spilt product.Avoid dispersal of spilt material and runoff and contact with soil,waterways,drains and rm the relevant authorities if the product has caused environmental pollution (sewers,waterways,soil or air).Water polluting material.May be harmful to the environment if released in large quantities.Large spill:Stop leak if without risk.Move containers from spill area.Dilute with water and mopup if water-soluble.Alternatively,or if water-insoluble,absorb with an inert dry material and place in an appropriate waste disposal container.Dispose of via a licensed waste disposal contractor.Small spill :6.3Methods and materials for containment and cleaning up 6.1Personal precautions,protective equipment and emergency procedures For non-emergency personnel:For emergency responders :6.4Reference to other sectionsSee Section 1for emergency contact information.See Section 8for information on appropriate personal protective equipment.See Section 13for additional waste treatment information.No action shall be taken involving any personal risk or without suitable training.Evacuate surrounding areas.Keep unnecessary and unprotected personnel from entering.Do not touch or walk through spilt material.Avoid breathing vapour or mist.Provide adequate ventilation.Wear appropriate respirator when ventilation is inadequate.Put on appropriate personal protective equipment.If specialised clothing is required to deal with the spillage,take note of anyinformation in Section 8on suitable and unsuitable materials.See also Section 8for additional information on hygiene measures.::The information in this section contains generic advice and guidance.The list of Identified Uses in Section 1should be consulted for any available use-specific information provided in the Exposure Scenario(s).7.1Precautions for safe handling Protective measures :Advice on general occupational hygiene:Put on appropriate personal protective equipment (see Section 8).Persons with ahistory of skin sensitization problems should not be employed in any process in which this product is used.Do not get in eyes or on skin or clothing.Do not ingest.Avoid breathing vapour or mist.Avoid release to the environment.Refer to special instructions/safety data sheet.Keep in the original container or an approved alternative made from a compatible material,kept tightly closed when not in use.Empty containers retain product residue and can be hazardous.Do not reuse container.Eating,drinking and smoking should be prohibited in areas where this material is handled,stored and processed.Workers should wash hands and face before eating,drinking and smoking.Remove contaminated clothing and protective equipment before entering eating areas.See also Section 8for additional information on hygiene measures.accordance with local regulations.Store in original container protected from direct sunlight in a dry,cool and well-ventilated area,away from incompatible materials (see section 10)and food and drink.Keep container tightly closed and sealed until ready for use.Containers that have been opened must be carefully resealed and kept upright to prevent leakage.Do not store in unlabelled e appropriate containment to avoid environmentalcontamination.storage,including any incompatibilities7.3Specific end use(s)Recommendations::Industrial sector specific solutionsNot available.Not available.Storage hazard class Huntsman Advanced Materials:Storage class 10,Environmentally hazardous liquidsRecommended monitoring proceduresOccupational exposure limits If this product contains ingredients with exposure limits,personal,workplaceatmosphere or biological monitoring may be required to determine the effectiveness of the ventilation or other control measures and/or the necessity to use respiratory protective equipment.Reference should be made to European Standard EN 689for methods for the assessment of exposure by inhalation to chemical agents and national guidance documents for methods for the determination of hazardous substances.Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes,mists or dusts.Eye/face protection::No exposure limit value known.Skin protectionAppropriate engineering controls:No special ventilation requirements.Good general ventilation should be sufficient to control worker exposure to airborne contaminants.If this product containsingredients with exposure limits,use process enclosures,local exhaust ventilation or other engineering controls to keep worker exposure below any recommended or statutory limits.Wash hands,forearms and face thoroughly after handling chemical products,beforeeating,smoking and using the lavatory and at the end of the working period.Appropriate techniques should be used to remove potentially contaminated clothing.Contaminated work clothing should not be allowed out of the workplace.Wash contaminated clothing before reusing.Ensure that eyewash stations and safety showers are close to the workstation location.8.2Exposure controls Hygiene measures :No DELs available.Predicted effect concentrations No PECs available.The information in this section contains generic advice and guidance.The list of Identified Uses in Section 1should be consulted for any available use-specific information provided in the Exposure Scenario(s).8.1Control parametersDerived effect levels Individual protection measuresIn case of inadequate ventilation wear respiratory protection.Respirator selection must be based on known or anticipated exposure levels,the hazards of the product and the safe working limits of the selected respirator.be worn at all times when handling chemical products if a risk assessment indicates this is necessary.Respiratory protection:Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.:Environmental exposure controls:Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation.In some cases,fume scrubbers,filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.Body protection:Other skin protectionAppropriate footwear and any additional skin protection measures should beselected based on the task being performed and the risks involved and should be approved by a specialist before handling this e gloves approved to relevant standards e.g.EN 374(Europe),F739(US).Suitabilityand durability of a glove is dependent on usage,e.g.frequency andduration of contact,chemical resistance of glove material and dexterity.Always seek advice from glove suppliers.Additional information can be found for instance at www.gisbau.de.Not available.Physical state Melting point/freezing point Initial boiling point and boiling rangeVapour pressure Relative density Vapour density Solubility(ies)Liquid.Not available.Not available.Not available.Not available.Not available.Odour pH Not available.Colour Evaporation rateNot available.Auto-ignition temperature Flash pointNot available.Closed cup:110°C [DIN 51758EN 22719(Pensky-Martens Closed Cup)]Not available.Not available.Not available.Not available.Odour threshold Partition coefficient:n-octanol/waterUpper/lower flammability or explosive limits :::::::::::::::9.1Information on basic physical and chemical properties Appearance Burning time Not applicable.Burning rateNot applicable.::Decomposition temperature:Not available.Flammability (solid,gas):Not available.Water solubility:Not available.Explosive properties :Not available.Oxidising properties :9.2Other information Density: 1.05g/cm 3[25°C (77°F)]10.6Hazardousdecomposition products10.4Conditions to avoid No specific data.Under normal conditions of storage and use,hazardous decomposition products should not be produced.The product is stable.10.2Chemical stability No specific data.:::10.5Incompatible materials :10.3Possibilityof hazardous reactions :Under normal conditions of storage and use,hazardous reactions will not occur.10.1Reactivity :No specific test data related to reactivity available for this product or its ingredients.Acute toxicityIrritation/Corrosion Conclusion/Summary:Not available.11.1Information on toxicological effectsmolecular weight<700):Slightly irritating to the skin.bisphenol F-epoxy resin:Slightly irritating to the skin.Eyes:reaction product:bisphenol A-(epichlorhydrin);epoxy resin(number averagemolecular weight<700):Slightly irritating to the eyes.bisphenol F-epoxy resin:Non-irritating to the eyes.Conclusion/Summary:Not available.Conclusion/Summary:Not available.CarcinogenicityPotential chronic health effectsPotential acute health effects Inhalation :Exposure to decomposition products may cause a health hazard.Serious effectsmay be delayed following exposure.Irritating to mouth,throat and stomach.:Ingestion Skin contact :Irritating to skin.May cause sensitisation by skin contact.Irritating to eyes.:Eye contact TeratogenicityReproductive toxicity Symptoms related to the physical,chemical and toxicological characteristics Skin contact Ingestion Inhalation No specific data.No specific data.Adverse symptoms may include the following:irritation redness:::Eye contact :Adverse symptoms may include the following:irritation watering rednessNot available.Information on the likely routes of exposure:Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure Long term exposure Potential immediate effects Potential delayed effects ::Potential immediate effectsPotential delayed effects ::Not available.Not available.Not available.Not available.Once sensitized,a severe allergic reaction may occur when subsequently exposed to very low levels.General:No known significant effects or critical hazards.Carcinogenicity :No known significant effects or critical hazards.Mutagenicity :No known significant effects or critical hazards.Teratogenicity:Conclusion/Summary :Not available.Developmental effects :No known significant effects or critical hazards.Fertility effects :No knownsignificant effects or critical hazards.Other information :Not available.12.1ToxicityMobilityNot available.:12.3Bioaccumulative potential 12.6Other adverse effectsNo known significant effects or critical hazards.12.2Persistence and degradability Conclusion/Summary :reaction product:bisphenol A-(epichlorhydrin);epoxy resin (number average molecular weight <700):Not readily biodegradable.12.4Mobility in soil Soil/water partition coefficient (K OC )Not available.:12.5Results of PBT and vPvB assessment :12.7Other ecological informationNot applicable.The generation of waste should be avoided or minimised wherever possible.Significant quantities of waste product residues should not be disposed of via the foul sewer but processed in a suitable effluent treatment plant.Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.Disposal of this product,solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements.Waste packaging should be recycled.Incineration or landfill should only be considered when recycling is not feasible.This material and its container must be disposed of in a safe way.Care should be taken :Methods of disposal The information in this section contains generic advice and guidance.The list of Identified Uses in Section 1should be consulted for any available use-specific information provided in the Exposure Scenario(s).13.1Waste treatment methods ProductEuropean waste catalogue (EWC)Yes.Hazardous waste :containers or liners may retain some product residues.Avoid dispersal of spilt material and runoff and contact with soil,waterways,drains and sewers.PackagingMethods of disposal:Special precautions:The generation of waste should be avoided or minimised wherever possible.Waste packaging should be recycled.Incineration or landfill should only be considered when recycling is not feasible.This material and its container must be disposed of in a safe way.Care should betaken when handling emptied containers that have not been cleaned or rinsed out.Empty containers or liners may retain some product residues.Avoid dispersal of spilt material and runoff and contact with soil,waterways,drains and sewers.Environmentally hazardous substance,liquid,n.o.s.BISPHENOL A EPOXY RESINEnvironmentally hazardous substance,liquid,n.o.s.(BISPHENOL A EPOXY RESIN)Marine pollutant (reaction product:bisphenol A-(epichlorhydrin);epoxy resin (number average molecular weight <700),bisphenol F-epoxy resin)Environmentally hazardous substance,liquid,n.o.s.(BISPHENOL A EPOXY RESIN)UN3082not available UN3082UN308214.1UN number14.2UN proper shipping nameADN/ADNR IMDG IATA ADR/RID14.7Transport in bulk according to Annex II of MARPOL 73/78and the IBC Code:Not applicable.National regulations Other EU regulations Not applicable.Annex XVII -Restrictions on the manufacture,placing on the market and use of certain dangerous substances,mixtures and articles :Europe inventory :All components are listed or exempted.Black List Chemicals :Not listed Priority List Chemicals :Not listed Integrated pollution prevention and control list (IPPC)-Air :Not listedIntegrated pollution prevention and control list (IPPC)-Water :Not listedChemical WeaponsConvention List Schedule I Chemicals:Not listedChemical WeaponsConvention List Schedule II Chemicals:Not listedChemical WeaponsConvention List Schedule III Chemicals:Not listedInternational regulationsReferences:The provision of Safety Data Sheets comes under Regulation 6of CHIP (CHIP is the recognised abbreviation for the Chemicals Hazard Information and Packaging Regulations).This is an addition to the Health and Safety at Work Act 1974.15.1Safety,health and environmental regulations/legislation specific for the substance or mixture EU Regulation (EC)No.1907/2006(REACH)Annex XIV -List of substances subject to authorisation 15.2Chemical Safety Assessment This product contains substances for which Chemical Safety Assessments are still required.Substances of very high concern :None of the components are listed.16November 2011Date of printingDate of issue/Date of revisionVersionNotice to readerDate of previous issue ::::R21/22-Harmful in contact with skin and if swallowed.R34-Causes burns.R38-Irritating to skin.R36/38-Irritating to eyes and skin.R43-May cause sensitisation by skin contact.R51/53-Toxic to aquatic organisms,may cause long-term adverse effects in the aquatic environment.:Full text of abbreviated R phrasesC -Corrosive Xn -Harmful Xi -IrritantN -Dangerous for the environment :Full text of classifications[DSD/DPD]Indicates information that has changed from previously issued version.16November 2011No previous validation.1Full text of abbreviated H statements:Abbreviations and acronyms:ATE =Acute Toxicity EstimateCLP =Classification,Labelling and Packaging Regulation [Regulation (EC)No.1272/2008]DNEL =Derived No Effect LevelEUH statement =CLP-specific Hazard statement PNEC =Predicted No Effect Concentration RRN =REACH Registration Number Classification according to Regulation (EC)No.1272/2008[CLP/GHS]Procedure used to derive the classification according to Regulation (EC)No.1272/2008[CLP/GHS]Full text of classifications [CLP/GHS]:H302Harmful if swallowed.H312Harmful in contact with skin.H314Causes severe skin burns and eye damage.H315Causes skin irritation.H317May cause an allergic skin reaction.H318Causes serious eye damage.H319Causes serious eye irritation.H411Toxic to aquatic life with long lasting effects.Acute Tox.4,H302ACUTE TOXICITY:ORAL -Category 4Acute Tox.4,H312ACUTE TOXICITY:SKIN -Category 4Aquatic Chronic 2,H411AQUATIC TOXICITY (CHRONIC)-Category 2Eye Dam.1,H318SERIOUS EYE DAMAGE/EYE IRRITATION -Category 1Eye Irrit.2,H319SERIOUS EYE DAMAGE/EYE IRRITATION -Category 2Skin Corr.1B,H314SKIN CORROSION/IRRITATION -Category 1B Skin Irrit.2,H315SKIN CORROSION/IRRITATION -Category 2Skin Sens.1,H317SKIN SENSITIZATION -Category 1Skin Corr.1B,H314Eye Dam.1,H318Skin Sens.1,H317Aquatic Chronic 2,H411MSDS no.:00057330and belief accurate at the date of publication,NOTHING HEREIN IS TO BE CONSTRUED AS A WARRANTY, EXPRESS OR OTHERWISE.IN ALL CASES,IT IS THE RESPONSIBILITY OF THE USER TO DETERMINE THE APPLICABILITY OF SUCH INFORMATION AND RECOMMENDATIONS AND THE SUITABILITY OF ANY PRODUCT FOR ITS OWN PARTICULAR PURPOSE.THE PRODUCT MAY PRESENT HAZARDS AND SHOULD BE USED WITH CAUTION.WHILE CERTAIN HAZARDS ARE DESCRIBED IN THIS PUBLICATION,NO GUARANTEE IS MADE THAT THESE ARE THE ONLY HAZARDS THAT EXIST.Hazards,toxicity and behaviour of the products may differ when used with other materials and are dependent upon the manufacturing circumstances or other processes.Such hazards,toxicity and behaviour should be determined by the user and made known to handlers,processors and end users.ARALDITE®is a registered trademark of Huntsman Corporation or an affiliate thereof in one or more countries, but not all countries.NO PERSON OR ORGANIZATION EXCEPT A DULY AUTHORIZED HUNTSMAN EMPLOYEE IS AUTHORIZED TO PROVIDE OR MAKE AVAILABLE DATA SHEETS FOR HUNTSMAN PRODUCTS.DATA SHEETS FROM UNAUTHORIZED SOURCES MAY CONTAIN INFORMATION THAT IS NO LONGER CURRENT OR ACCURATE. NO PART OF THIS DATA SHEET MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM,OR BY ANY MEANS,WITHOUT PERMISSION IN WRITING FROM HUNTSMAN.ALL REQUESTS FOR PERMISSION TO REPRODUCE MATERIAL FROM THIS DATA SHEET SHOULD BE DIRECTED TO HUNTSMAN,MANAGER, PRODUCT SAFETY AT THE ABOVE ADDRESS.。

化学物资安全数据表1.0 用语的定义1.1 理化性质：是对化学品外观和状态的直观描述。

主要包括常温床压下该物质的颜色、气味、存在的状态及溶解性。

溶解性指在常温堂压下该物质在常用溶济（以水为主）中的溶解性，分别用混溶、易溶、溶干、微溶、不溶等表示其溶解的程序。

1.2 危险特性：是指简要概述化学品燃烧爆炸的性能和一些简单的化学性质。

主要包括遇明火、高温、氧化剂等可能产生的危害，遇水、酸、碱和一些活性物质的反应，以及氧化性、腐蚀性等。

1.3 毒性：是指毒物引起机体损伤的能力。

化学毒物侵入机体引起伤害，主要有三种途径：吸入、食入和经皮肤吸收。

在生产作业条件下，化学物质主要通过呼吸道和皮肤进入人体，职业中毒时经口途径比较次要。

手册中收录的内容，主要是以有关专著中途述的毒物中毒典型临床表现为主，很少涉及化验和特殊检查，对一些人体中毒资料中记载较少和毒物，以动物毒性资料补充之。

1.4 急救措施：是指现场作业人员意外地受到化学毒物的伤害时，所需采取的自救或互救的简要的处理方法。

1.5 防护措施：分为组织措施（严格执行有关法令、法规，改善劳动组织，卫生宣传，建立群众性组织）；技术措施（工艺改革和技术革新，厂房设计的卫生要求，通风措施）和保健措施（对毒物的监测，个人卫生和个人防护，保健膳食和进行就业前及定期的健康检查）。

1.6 泄漏处置：是指由于在生产、储运过程中发生的破裂、倒洒事故，造成危险品的外漏。

1.7 储运要求：是指危险货物在储运和运输过程中的一般注意事项。

包括储存条件，禁忌物，分装和运输的一般要求，未涉及包装和储运的容器。

2.0 主要化学品及其相应的性质。

Material Safety Data Sheet(MSDS)according to(EC)1907/2022(REACH)物质安全数据表(MSDS)遵照(EC)1907/2022(REACH)(TRADE)NAME OF THE CHEMICAL化学品名SECTION1.IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY第一部份物质/配制品/公司名称1.1Identification of the chemical(substance or preparation)化学品(物质或者配制品)名称1.2Use of the chemical化学品用途1.3Company identification公司信息Company name公司名:Address 地址:Postal code 邮编:Country 国家:Telephone number 电话:Fax number 传真:E-Mail (person responsible for SDS)责任人邮箱:Date of latest version SDS 最新版日期:1.4Emergency Telephone应急电话In case of an emergency, please contact:紧急情况请联系：第二部份危（wei）险鉴定POSITION/INFORMATION ON INGREDIENTS第三部份成份组成信息3.1General Chemical Description总体化学品描述3.2Base Substances of Preparation配制品基本成份components 成份EC-No.CAS-No.Content(%or range)浓度(浓度范围)3.3Declaration of Ingredients according to EC1907/2022(REACH Regulation)(If necessary)遵照EC1907/2022(REACH)成份声明 (如果需要)Hazardous components 危（wei）险成份EC-No.CAS-No.Content(%or range)浓度(浓度范围)Classification分类Please refer to section 16 for an overview of all R-phrases mentioned here.涉及的所有风险分级(R-phrases)请参阅第十六部份。

化学危险品清单和安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（1 0）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂。

化学危险品清单和安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（1 0）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂化学物质安全数据表（MSDS清单）注：危害性：（1）爆炸性（2）易燃性（3）可燃性（4）自燃性（5）腐蚀刺激性（6）急性毒性（7）特定毒性（8）破坏臭氧层物质（9）氧化性（10）有机氯溶剂。

材料安全数据表(MSDS)1. 化学品及企业标识产品名称：甲基乙烯基硅橡胶混炼胶通用型模压胶系列： GA-1133、GA-1143、GA-1153、GA-1163、GA-1173、GA-1183 通俗名称：硅橡胶混炼胶公司名称：深圳市正安有机硅材料有限公司 / 东莞市正安有机硅科技有限公司公司地址：深圳市坪山新区碧岭社区沙坑路29号 / 东莞市横沥镇西城工业二区B3栋电话号码：86-755-89784381 / 86-769-81002333传真号码：86-755-89784382 / 86-769-81002888编制日期：2008年2月28日修改日期：2017年6月6日起草/修订部门：研发部2. 危险性概述分类名称：无适用的分类。

危险性：可燃性物质。

有害性：不慎入眼时：对眼睛有轻微刺激性。

粘附皮肤时：对皮肤刺激小。

吸入体内时：吸入体内后危险性小。

误饮入口时：危害性极小。

其它：无数据。

3. 成分/组成信息纯物质/混合物：混合物俗称化学名称含量 CAS编号生胶甲基乙烯基硅橡胶 50~80% 68083-18-1白炭黑二氧化硅 10~40% 7631-86-9结构化控制剂羟基硅油 1~6% 70131-67-8脱模剂硬脂酸 0~1% 57-11-44. 急救措施不慎入眼时：马上用流水冲洗眼睛15分钟以上，根据情况接受医生的诊断。

粘附皮肤时：马上用流水冲洗，用肥皂仔细清洗，并根据症状接受医生诊断。

吸入体内时：移至空气新鲜处，保持安静，并根据症状接受医生诊断。

误饮入口时：马上将本品吐出，并根据症状接受医生诊断。

5. 消防措施灭火方法：切断火势的燃烧源，使用下述灭火剂灭火。

另外，在不会扩大火势的条件下向周围的贮存罐和建筑物喷水，使它们冷却。

灭火作业时要顶风操作，根据情况戴上防护用具。

灭火剂：泡沫灭火剂、粉末灭火剂和二氧化碳灭火剂。

6. 泄漏应急处理：清扫干净并放入适当的容器中.7. 操作处置及存储操作时：严禁火种。