cognex 太阳能行业产品手册

DataMan®8050快速参考指南2017/11/15预防措施安装Cognex产品时请遵守这些注意事项，以降低受伤或设备损坏的风险︰l为了减少由于过电压、线路噪音、静电放电(ESD)、电涌或其他电源不正常原因造成的损害或故障风险，可以远离高电压电源来确定线缆电路。

l未经负责合规性一方的明确批准，擅自更改或修改可能使用户操作设备的权限失效。

l如果维修圈或折弯半径比电缆直径紧10倍，会降低电缆屏蔽效果或损坏电缆。

折弯半径必须在距接口至少六英寸处开始。

l应遵照本手册中的说明使用该设备。

l所有规格仅供参考，如有更改，恕不另行通知。

1LED瞄准器指南2触发器（按住读码）3通信模块插入点4挂绳钩5指示灯6RS-232连接7USB连接8电源插头（24伏，最大15瓦）9备用电源连接器（24伏，最大15瓦，连接器周围的塑料部件上标有极性）10以太网连接串行/USB滑件(DMCM-SERIALM-00)以太网滑件(DMCM-ENETM-00)蓝牙滑件(DMCM-BTM-00)无线滑件(DMCM-WLESSM-00)充电基站(DMA-CBASE-01)智能基站(DMA-IBASE-01)智能蓝牙基站(DMA-IBASE-BT-01)智能蓝牙基站(DMA-IBASE-BT-02)基站电源(DMA-24VPWR-xx)读码器电源(DM100-PWR-00)无线读码器电池(DMA-HHBATTERY-01)多电池充电器(DMA-MBC-xx)POE适配器(CPS-24V-POE1)POE适配器(CPS-24V-POE4)壁挂支架(DMA-WALL-8000-00)基站壁挂支架(DMA-IBASE-WALL-00)POE适配器(CPS-AC-POE1A-xx)支架(DM-STAND-00)电缆读码器RS-232螺旋电缆，2.5米(DM8000-RS232-02)读码器RS-232工业电缆，2.5米(DM8000-RS232IND-02)读码器RS-232螺旋电缆，5米(DM8000-RS232-05)USB螺旋电缆，2.5米(DM8500-USBC-02)以太网电缆，2.5米(DM8000-ECABLE-02)以太网电缆，30米(DM8000-ECABLE-30)以太网电缆，5米(DM8000-ECABLE-05)USB电缆，2.5米(DM8500-USB-00)以太网螺旋电缆，5米DM8000-ECABLEC-05*基站的RJ25(RJ12)至DSUB9电缆，5米DMA-RS232RJ-05*包括DM8000-ECABLE-X的校准电缆长度不应超过50米。

SOLAR KITA SUSTAINABLE BATTERY CHARGING GEAR User ManualWSBC-50Contents1. General Information (1)1.1 Key Design Features (1)1.2 Warnings (2)2. Components and accessories (3)2.1 Accessories (3)3. Specifications (4)3.1 Module electrical specifications (4)3.2 Module mechanical specifications (4)3.3 Charge controller specifications (4)3.4 Rooftop box specifications (5)4. Packaging information (6)5. Installation (7)5.1 Wiring guidelines (7)5.2 Kit fixation guidelines (8)6. Operating Instructions (9)6.1 Charge controller (9)6.2 Features of charge controller (9)6.3 Display symbols (9)6.4 Special Instructions (10)7. Troubleshooting (10)8. Frequently Asked Questions (11)9. Limited Warranty (11)User manual – Ceyone solar kit1.General InformationPlease read this user manual carefully before using the product.Dear Customer,Thank you for purchasing Ceyone solar kit.We hope that you get best results from our product which has been manufactured with high quality and state of the art technology. Please read this entire user manual and all its accompanying documents carefully before using the product. Keep this manual and its accompanying documents safe/stored to refer them in the future.1.1 Key Design FeaturesSuperior product efficiencies as per international benchmarksOur high quality components are designed for best in class product durabilityMaximizes the state of charge of the battery which ensures that the lifetime ofbattery is extendedAdequate protection ensuring hazard free operationDesigned for off-grid applications1.2 WarningsPlease read all the warnings carefully before operating the product. It is necessary to understand and keep them in mind when the system is in use. Any negligence may lead to severe damage to you and your surroundings.Disconnect all the operating battery Exceeding current and voltage rating Use in presence ofponents and accessories2.1 Accessories3.Specifications3.1 Module electrical specificationsThe figure below shows the performance curve of 50Wp module under Standard Test Conditions (STC): 1000 W/m 2 irradiance, Air Mass 1.5 and 25°C cell temperature.3.2 Module mechanical specifications3.3 Charge controller specifications3.4 Rooftop box specifications3.5 Mounting kit specifications4.Packaging information1.Rooftop box2.Charge controller3.Mounting bracket & fixing ancillariesNote: These additional inclusions are kept in position by utilizing double sided tape. Exercise caution whenremoving/ detaching the accessories.5. Installation5.1 Wiring guidelinesIn order to achieve optimized output, it is recommended to that the electrical connections are made in the correct manner using 14 gauge wire. Verify that the connections are secure to ensure safe operation of the kit. It is recommended to use a 10 amp rated fuse before the battery for enhanced safety. As a precaution use properly insulated tools & appropriate PPE’s.Line Diagram Of ConnectionExterior Wiring Guide10 Amp Fuse 14 GaugeWire5.2 Kit fixation guidelinesThe following steps should be adhered to for kit installation/ fixation.1.Connecting the rooftop box: The solar panel need to be connected to the rooftop box as shown in wiringdiagram. Please use appropriate mating connectors between the inter-connecting wire(s) to ensure safe operation.2.Fixing rooftop box atop vehicle: The rooftop box should be fixed atop the vehicle. It is recommended touse appropriate sealant & dispenser for this operation. Kindly allow the sealant to dry for minimum of 6~8 hours in a moisture free environment to obtain a permanent bond.3.Fixing the mounting structure on solar module: Use the 4 mounting clamps and fix each of themalongside the mounting hole as provided in the rear side of the module.4.Fixing ancillaries: Follow the mounting process by utilizing M6 bolt, M6 split lock washer, M6 flat washeron one side of the mounting clamp Lock the bolt by in position by utilizing M6 flat washer and M6 nut on the other side. Use appropriate tools like Spanner, Plier, etc. for obtaining a perfect fit. Connecting the rooftop box Fixing rooftop box atop vehicleModule fixation guide Mounting kit fixation guide6.Operating Instructions6.1 Charge controllerBefore making initial connections, please ensure thatthe battery has enough charge or is at adequatevoltage level such that the controller can sense thebattery.The controller is only suitable for LEAD ACIDBATTERIES: OPEN, AGM, and GEL type. It is notsuited for nickel metal hydride, lithium ions or otherbatteries. Charge controller is only suitable ofcontrolling solar PV modules as input. Never connectanother charging source to the charge controller.6.2 Features of charge controller1.The PMW charge controller is IP 68 with built-in open circuit and reverse protection2.It is equipped with dual mosfet for reverse current and low heat protection3.It has enhanced size of display for clearly observing and recording the dataDisplay the battery voltageIndication that the solar panel is charging the batteryDisplays the battery state of chargeonce its voltage is above 12.6V6.4 Special Instructions3.To obtain maximum output it is suggested that the panel’s direction is adjusted such that it faces the sun.4.Locate a clear sunlit area, free from overhanging branches, wires or obstructions to ensure maximumgeneration5.Broken modules cannot be repaired and contact with any module surface or frame can lead to electricalshock. Do NOT use a module with broken glass or torn substrate6.Do not disassemble the modules or remove any part of the module7.Do not drop Module or allow objects to fall on the Module. Do not stand or step on the Module8.Ensure the battery clamps/ connectors do not come in contact with one another to avoid short circuiting9.Ensure that all the electrical connections are secured before using the kit. Verify that the battery is beingcharged by the kit10.V erify the tightness of mechanical connections before using the kit11.P lease connect any type of load via the battery only7.TroubleshootingThe common problems are listed below. For any additional technical support, please get in touch with the local sales coordinator.1)PV Array Short CircuitIn case of array short circuit, check all the interconnections. In case of fault, immediately disconnect the faulty connection. Please take help of local sales coordinator if you find it difficult to repair the fault.2)Load Short CircuitCheck the continuity of fuse placed before battery. If blown, replace the faulty fuse and the faulty wire as necessary.3)Battery Reverse PolarityThe controller has protection against battery reverse polarity. It is however suggested to immediately correct the wiring to prevent any mishap.4)Overheating ProtectionIf the temperature of the controller heat sink exceeds 85 °C, the controller will automatically start overheating protection. However in case the system temperature rises, please keep in cool place such that its temperature drops before re-using it.5)High Voltage TransientsIf you are using this system in lightning prone areas, it is suggested that additional externalsuppression (such as using the system in range of lightening arrestor, etc.) is used.Question 1: Can the kit charge two or more 12 V batteries connected in parallel?Answer: Yes, it is possible if the batteries have the same type & capacity and are wired in parallel as a single 12V battery bank.Question 2: Is there any risk that the solar kit will over charge my battery?Answer: One of the functions of the solar charge controller is to ensure that your battery is not over charged. Question 3: Do I need to clean the solar panels?Answer: Yes, it is recommended for better performance. Dust and dirt should first be swept off the panel surface using a soft brush. When the sweeping is complete, use a wet cloth to wipe the panel surface to remove remaining dirt and/or stains.Question 4: Can I place my solar panels anywhere?Answer: To maximize generation, ensure that the tilt angle of system resembles the latitude of the place. If this is not possible, kindly ensure that the module is facing the sun and receives maximum irradiation. Further the solar module should not be operated under shadow.9.Limited WarrantyThe solar module of the kit has a 5 years of limited warranty and 10 years of power output warranty. The controller & rooftop box comes with a 1 year limited warranty. This warranty is valid against defects in materials and workmanship. It is not valid against defects resulting from, but not limited to:•Misuse and/or abuse, neglect or accident.•Improper installation, including but not limited to, improper environmental protection and improper hook-up•Damage in handling, including damage encountered during shipment or installation•Acts of God, including lightning, floods, earthquakes, fire, high winds, etc.•Exceeding the unit’s design limitNote:1.Warranty would stand void for module(s) whose type or serial numbers appears to be changed, erased,removed, illegible or in any manner altered or tampered.2.This warranty does not cover any cost associate with on-site labour and any cost associated with theinstallation, removal, reinstallation, shipping or transportation of the kit(s), any customs clearance or any other cost of return or re-shipment of kit(s).3.Any damages caused by abrasion, artificial damage or animals are exempt from this warranty.4.Defects and/or failures caused by unauthorized maintenance, operation or modification regardless ofwhether such act is wilful misconduct or negligence are exempted from warranty。

Purp ose of this guideThis guide contains information regarding the installation and safe handling of Conergy photovoltaic modules (hereafter referred to as "modules"). All instructions should be read and understood before attempting installation. If there are any questions, please contact your dealer or Conergy for further information. The installer should conform to all safety precautions in the guide when installing modules. Before installing a solar photovoltaic system, the installer should become familiar with the mechanical and electrical requirements for photovoltaic systems. Keep this guide in a safe place for future reference.General|Installing solar photovoltaic systems requires specialized skills and knowledge.The installer assumes all risk of injury, including risk of electric shock. Module installation should be performed only by qualified persons.|All modules come with a permanently attached junction box and #12 AWG (4mm²) wire terminated in Multi Contact PV connectors. Your dealer canprovide additional extension cables to simplify module wiring.|Each individual module can generate DC voltages greater than 30 volts (V) when exposed to direct sunlight. Contact with a DC voltage of 30V or more is potentially hazardous. Exercise caution when wiring or handling modulesexposed to sunlight.|When disconnecting wires connected to a photovoltaic module that is exposed to sunlight, an electric arc may occur. Arcs can cause burns, start fires orotherwise create safety problems. Exercise caution when disconnecting wiring on modules exposed to sunlight.|Photovoltaic solar modules convert light energy to direct-current electrical energy, and are designed for outdoor use. Proper design of support structures is the responsibility of the system designer and installer.|Modules may be ground mounted, pole mounted, or mounted on rooftops.Do not attempt to disassemble the module, and donot remove any attached nameplates or components.Doing so will void the warranty.|Do not apply paint or adhesive to the module.Do not use mirrors or other hardware to artificiallyconcentrate sunlight on the module.|When installing modules, observe all applicable local, regional and national codes and regulations. Obtain a building and/or electrical permit where required.Safety precautions for installing a solar photovoltaic system|Solar modules produce electrical energy when exposed to sunlight.DC voltages may exceed 30V on a single exposed module.|Only connect modules with the same rated output current in series.If modules are connected in series, the total voltage is equal to the sum of the individual module voltages.|Only connect modules or series combinations of modules with the same voltage in parallel. If modules are connected in parallel, the total current isequal to the sum of individual module or series combination currents.|Keep children well away from the system while transporting and installing mechanical and electrical components.|Completely cover all modules with an opaque material during installation to prevent electricity from being generated.Do not wear metallic rings, watchbands, ear, nose, orlip rings or other metallic devices while installing ortroubleshooting photovoltaic systems.Use appropriate safety equipment (insulated tools,insulating gloves, etc) approved for use on electricalinstallations.|Observe the instructions and safety precautions for all other components used in the system, including wiring and cables, connectors, DC-breakers, mounting hardware, inverters, etc.|Use only equipment, connectors, wiring and mounting hardware suitable for use in a photovoltaic system.|Always use the same type of module within a particular photovoltaic system. |Under normal operating conditions, PV modules will produce currents and voltages that are different than those listed in the date sheet. Data sheetvalues are applicable at standard test data.|Short-circuit current and open-circuit voltages should be multiplied by a factor of 1.25 when determining component voltage ratings, conductor ampacity, fuse sizes and size of controls connected to the module or system output.Refer to Section 690-8 of the National Electrical Code (NEC) for an additional multiplying factor of 125 percent (80 percent de-rating) which may be applicable.General installation notes|Drainage holes must not be covered with parts of the mounting system. The junction box has a breather port which must be mounted facing downward and cannot be exposed to the rain. The junction box should be on the higher side of the module when it is mounted in order to orient the breather port correctly.|Do not lift the module by grasping the module's junction box or electrical leads. |Do not stand or step on module.|Do not drop the module or allow objects to fall on the module.|Do not place any heavy objects on the module.|Inappropriate transport and installation may damage the module glass or frame.Mechanical InstallationSelecting the location|Select a suitable location for installation of the module.For optimum performance, the module must be facing true south in northernlatitudes and true north in southern latitudes.For detailed information on optimal module orientation, refer to standard solarphotovoltaic installation guides or a reputable solar installer or systems integrator.|The module should not be shaded at any time of the day.|Do not install the module near equipment or in locations where flammable gasescan be generated or collected.Observe all instructions and safety precautions included with the mountingsystem to be used with the module.|Do not drill holes in the glass surface of the module. Doing so will void the warranty.|Do not drill additional mounting holes in the module frame. Doing so will void thewarranty.|Modules must be securely attached to the mounting structure using fourmounting points for normal installation. If heavy wind or snow loads areanticipated, additional mounting points should also be used. Please see thedrawing below.|Load calculations are the responsibility of the system designer or installer.|The mounting structure and hardware must be made of durable, corrosion- andUV-resistant material.Mounting methods1.Mounting With Bolts|The module must be attached and supported by at least four bolts throughthe indicated mounting holes.|Most installations will use the four inner mounting holes on the module frame.Depending on the local wind and snow loads, additional mounting points maybe required.Please carefully read the following installation and safety instructions.Non-compliance with these instructions may void the module warranty.Page 1/22.Mounting With Clamping Hardware|If module clamps are used to secure the module, the torque on the clamp bolt should be around 8–10 Nm.| A minimum of four module clamps should be used, two on each long frame side,in the general clamping areas denoted by the wide arrows on the drawing.|Depending on the local wind and snow loads, additional module clamps may be required.All dimensions in mm3.Other|Other mounting methods are acceptable as long as the minimum requirement as described under 2. Mounting with clamping hardware are met.Electrical Installation Grounding|All module frames must be properly grounded.|Observe all local electric codes and regulations.| A bonding or toothed washer is required to make proper and reliable electrical grounding connection with the anodized aluminum frame.|Devices listed and identified for grounding metallic frames of PV modules are permitted to ground the exposed metallic frames of the module to grounded mounting structures. Per NEC 250.136, electrical equipment secured to and in electrical contact with a metal rack or structure provided for its support and grounded by one of the means indicated in 250.134 shall be considered effectively grounded.|Consider using a lay-in lug, rated for outdoor use (IllscoGBL4 DBT or equivalent),if the module grounding conductor is to be larger than #10 AWG.|When using lay-in lugs, the grounding conductor should be inserted into the opening indicated in the figure, and secured using the set screw.General electrical installation|Do not use modules of different configurations in the same system.|This module is supplied with Multi Contact connectors for electrical connections. |Refer to Section 690.31 of the NEC to determine appropriate types and temperature ratings of conductors. Wiring should be #12 AWG, 4mm² (minimum) and must be temperature rated at 90 °C (minimum).|Completely cover system modules with an opaque material to prevent electricity from being generated while disconnecting conductors.|Refer to Sections 690.8 and 310 of the NEC to determine overcurrent, conductor ampacity and size requirements.|In Canada, installation shall be in accordance with CSA C22.1, Safety Standard for Electrical Installations, Canadian Electrical Code, Part 1.|For best performance, ensure that positive and negative DC wires run closely together avoiding loops.WARNING!Electrical shock hazard! Do not touch bare conductors or other potentially energized parts.MaintenanceConergy recommends the following maintenance items to ensure optimum performance of the module:|Clean the glass surface of the module as necessary. Use water and a soft sponge or cloth for cleaning. A mild, non-abrasive cleaning agent can be used if necessary. Do not use dishwasher detergent.|Electrical and mechanical connections should be checked periodically by qualified personnel to verify that they are clean, secure and undamaged.|Check the electrical and mechanical connections periodically to verify that they are clean, secure and undamaged.|Problems should only be investigated by qualified personnel.|Observe the maintenance instructions for all other components used in the system.Shutting down the system|Completely cover system modules with an opaque material to prevent electricity from being generated while disconnecting conductors.|Disconnect system from all power sources in accordance with instructions for all other components used in the system.|The system should now be out of operation and can be dismantled. In doing so, observe the all safety instructions as applicable to installation.Electrical ratings of the concerned modules:S 180MU175MUQ 85MUMaximum Power (P MPP ) 180 W 175 W 85 W Output Tolerance –2/+ 3 %–2/+ 3 %+/- 5 %Rated Voltage (V MPP ) 35.6 V 35.2 V 17.6 V Rated Current (I MPP )5.05 A 4.95 A 4.83 A Open Circuit Voltage (V OC ) 44.4 V 44.2 V 21.9 V Short Circuit Current (I SC ) 5.4 A 5.2 A 5.14 A Maximum System Voltage 600 V 600 V 600 V Maximum Series Fuse Rating 15 A 15 A 15 A Fire ClassCCCThe electrical characteristics are within ±10 % of the indicated values of I , V , and P under Standard Test Conditions (irradiance of 1000 W/m , AM 1.5 spectrum, and a cell temperature of 25°C/77°F)Disclaimer of liabilityBecause the use of this manual and the conditions or methods of installation, operation, use and maintenance of photovoltaic products are beyond Conergy's control, Conergy does not accept responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way connected with such installation, operation, use or maintenance. No responsibility is assumed by Conergy for any infringement of patents or other rights of third parties, which may result from use of the PV product. No license is granted by implication or otherwise under any patent or patent rights.The information in this manual is based on Conergy's knowledge and experience and is believed to be reliable, but such information including product specification (without limitations) and suggestions does not constitute a warranty, expressed or implied. Conergy reserves the right to change the manual, the product, the specifications, or product information sheets without prior notice. Information about manufacturer:Conergy Inc.1730 Camino Carlos Rey, Suite 103Santa Fe, NM 87507USAPlease consult your dealer or the manufacturer concerning the warranty of your modules. If you have any further questions, your dealer will gladly assist you.Subject to technical modifications without notice. 2007 © Conergy, Inc.M O D U L _I n s t a l l a t i o n -U L -I M -E N G -0705 | 2007 © Conergy AGPage 2/2。

ALL-BLACK High density MONO PERC modulePRODUCT CERTIFICATES*HiDM-BlackMORE POWERMaximize the light absorption area, module efficiency up to 20.16 %Low temperature coefficient (Pmax): -0.37 % / °CMORE RELIABLECANADIAN SOLAR INC.545SpeedvaleAvenueWest,Guelph,OntarioN1K1E6,Canada,,*************************ISO 9001:2015 / Quality management systemISO 14001:2015 / Standards for environmental management systemOHSAS 18001:2007 / International standards for occupational health & safetyMANAGEMENT SYSTEM CERTIFICATES*320 W ~ 340 WCS1H-320|325|330|335|340MSUP TO 20.16%Heavy snow load up to 5400 Pa,wind load up to 2400 Pa*Better shading toleranceLower internal current, lower hot spot temperatureCell crack risk limited in small region, enhance the module reliability IEC 61215 / IEC 61730: VDE / CE / MCSUL 1703 / IEC 61215 performance: CEC listed (US) / FSEC (US Florida)UL 1703: CSA / IEC 61701 ED2: VDE / IEC 62716: VDE Take-e-wayAs there are different certification requirements in different markets, please contact your local Canadian Solar sales representative for the specific certificates applicable to the products in the region in which the products are to be used.CANADIAN SOLAR INC. is committed to providing highquality solar products, solar system solutions and services to customers around the world. No. 1 module supplier for quality and performance/price ratio in IHS Module Customer Insight Survey. As a leading PV project developer and manufacturer of solar modules with over 38 GW deployed around the world since 2001.*According to the applicable Canadian Solar Limited Warranty Statement.linear power output warranty*enhanced product warranty on materials and workmanship** For detail information, please refer to Installation Manual.MECHANICAL DATA Specification Data Cell Type Mono-crystalline Dimensions 1700 ˣ 992 ˣ 35 mm (66.9 ˣ 39.1 ˣ 1.38 in)Weight 19.2 kg (42.3 lbs)Front Cover 3.2 mm tempered glass Frame Anodized aluminium alloy J-Box IP68, 3 bypass diodes Cable 4.0 mm² (IEC), 12 AWG (UL)Cable Length 1350 mm (53.1 in) (Including Connector) Connector T4 series or H4 UTX or MC4-EVO2 Per Pallet 30 pieces Per Container (40‘ HQ) 780 piecesTEMPERATURE CHARACTERISTICS SpecificationDataTemperature Coefficient (Pmax) -0.37 % / °C Temperature Coefficient (Voc) -0.29 % / °C Temperature Coefficient (Isc)0.05 % / °C Nominal Module Operating Temperature44±3 °CPARTNER SECTIONRear ViewFrame Cross Section A-AThe specifications and key features contained in this datasheet may deviate slightly from our actual products due to the on-going innovation and product enhancement. Canadian Solar Inc. reserves the right to make necessary adjustment to the information described herein at any time without further notice.Please be kindly advised that PV modules should be handled and installed by qualified people who have professional skills and please carefully read the safety and installation instructions before using our PV modules.CANADIAN SOLAR INC.545SpeedvaleAvenueWest,Guelph,OntarioN1K1E6,Canada,,*************************December 2019. All rights reserved, PV Module Product Datasheet V5.583_ENELECTRICAL DATA | STC*CS1H320MS 325MS 330MS 335MS 340MS Nominal Max. Power (Pmax)320 W325 W 330 W 335 W 340 W Opt. Operating Voltage (Vmp)36.2 V 36.6 V 37.0 V 37.4 V 37.8 V Opt. Operating Current (Imp)8.85 A 8.88 A 8.92 A 8.96 A 9.00 A Open Circuit Voltage (Voc)44.0 V 44.1 V 44.2 V 44.3 V44.5 VShort Circuit Current (Isc)9.41 A 9.45 A9.49 A 9.53 A 9.57 AModule Efficiency 18.98%19.27%19.57%19.86%20.16%Operating Temperature -40°C ~ +85°C Max. System Voltage 1000V (IEC/UL)Module Fire Performance TYPE 1 (UL 1703) or CLASS C (IEC 61730) Max. Series Fuse Rating 15 A Application Classification Class A Power Tolerance0 ~ + 5 W* Under Standard Test Conditions (STC) of irradiance of 1000 W/m 2, spectrum AM 1.5 and cell temperature of 25°C.ELECTRICAL DATA | NMOT*CS1H320MS 325MS 330MS 335MS 340MS Nominal Max. Power (Pmax)236 W240 W 243 W 247 W 251 W Opt. Operating Voltage (Vmp)33.4 V 33.7 V 34.1 V 34.5 V 34.8 V Opt. Operating Current (Imp)7.07 A 7.11 A 7.14 A 7.17 A 7.20 A Open Circuit Voltage (Voc)41.0 V 41.1 V 41.2 V 41.3 V41.5 VShort Circuit Current (Isc)7.60 A7.63 A7.66 A 7.70 A 7.73 A* Under Nominal Module Operating Temperature (NMOT), irradiance of 800 W/m 2, spectrum AM 1.5, ambient temperature 20°C, wind speed 1 m/s.ENGINEERING DRAWING (mm)CS1H-330MS / I-V CURVES5°C 25°C 45°C 65°C1000 W/m 800 W/m 600 W/m 400 W/m200 W/m A A V12111098765432105 10 15 20 25 30 35 40 45 50 V5 10 15 20 25 30 35 40 45 501211109876543210。

Cognex视觉培训教程一、引言Cognex是一家专注于视觉技术的公司，其产品广泛应用于工业自动化领域。

Cognex视觉系统可以帮助企业提高生产效率、降低成本、提升产品质量。

为了更好地推广和应用Cognex视觉技术，本文将为您介绍Cognex视觉培训教程，帮助您快速掌握Cognex视觉系统的使用方法。

二、Cognex视觉系统简介1.Cognex视觉系统组成Cognex视觉系统主要由图像采集单元、图像处理单元和执行单元组成。

图像采集单元负责获取被测物体的图像信息；图像处理单元对采集到的图像进行处理和分析；执行单元根据图像处理结果进行相应的控制操作。

2.Cognex视觉系统特点（1）高精度：Cognex视觉系统具有高精度的图像处理能力，可满足各类高精度检测需求。

（2）高速度：Cognex视觉系统具有高速图像处理能力，可实时完成图像采集、处理和结果输出。

（3）易于集成：Cognex视觉系统可方便地与其他自动化设备集成，实现完整的自动化解决方案。

（4）强大的软件支持：Cognex提供了功能强大的视觉处理软件，支持用户进行二次开发，满足不同应用场景的需求。

三、Cognex视觉培训教程内容1.基础知识培训（1）视觉系统原理：介绍视觉系统的基本原理，包括图像采集、图像处理和图像分析等。

（2）视觉系统硬件：介绍Cognex视觉系统的硬件组成，包括相机、镜头、光源等。

（3）视觉系统软件：介绍Cognex视觉处理软件的使用方法，包括图像处理、算法设置、结果输出等。

2.实践操作培训（1）相机标定：教授如何对相机进行标定，确保图像采集的准确性。

（2）图像处理：教授如何对采集到的图像进行预处理，如滤波、二值化等。

（3）特征提取：教授如何从图像中提取目标特征，如边缘、面积、角度等。

（4）模板匹配：教授如何使用模板匹配算法进行目标识别。

（5）Blob分析：教授如何使用Blob分析算法进行目标检测和分类。

3.应用案例培训（1）介绍Cognex视觉系统在不同行业的应用案例，如电子制造、汽车制造、食品饮料等。