下载文档原格式
产品规格书(SPEC.)产品名称重量模块产品说明重量模块目录1.0Revision History (3)2.0General Description (4)3.0Selection Table (5)4.0Application Circuit and Description (5)5.0Pin Assignment (6)6.0Pin Description (8)7.0Electrical Characteristics (8)8.0Function Description (10)8.1IIC interface: (10)读取重量 (10)去皮&标定 (11)休眠118.2UART interface: (12)9.0Tool Information (14)1.0 Revision History2.0 General DescriptionBMH01xxx是Holtek推出的高精度称重模块。
BMH011xx为全桥双孔悬臂平行梁应变片传感器搭配Holtek专为高精度称重传感器而设计的24位A/D转换芯片，可做到1g或者更低的称重精度。
称重范围为1.5kg、5kg。
常应用于智能水杯，咖啡机等产品。
BMH012xx为半桥山型应变片传感器搭配Holtek专为高精度称重传感器而设计的24位A/D转换芯片，可做到5g或者更低的称重精度。
称重范围为20kg。
常应用于榨汁机、咖啡机等智能产品。
与同类型模块相比其主要优势是：1.内部集成稳压电源，宽电源输入范围2.待机功耗低：<1uA3.PCBA Size:12mm*13mm（BMH011XX）;16mm*16mm(BMH012XX)4.直接输出重量值，不需要用户在做AD转换，降低开发成本5.标准IIC/UART接口6.针对不同量测范围，提供不同模块选型7.IIC/UART命令动态去皮功能BMH011xx BMH012xx Application:3.0 Selection Table4.0 Application Circuit and DescriptionIIC接口UART接口注:1.若对精度及抗干扰效果有要求建议保留0.1uF及47uF电容。
G125-MV12005M3 P G125-MV12605M1PG125-FC11605F1-0150LG125-FC12605F1-0450LG125-FC13405F1-0150LG125 Series: 1.25mm Pitch High Reliability ConnectorsComponent SpecificationJune 2020Contents1. Description of Connector (2)2. Ratings (2)2.1. Materials (2)2.2. Electrical Characteristics (2)2.3. Mechanical Characteristics (3)2.4. Environmental Characteristics (3)2.5 Wire Termination information – Signal crimp products (3)2.6 Wire Termination information – Power crimp products (4)Appendix 1 (5)Appendix 1.1. – Gecko-SL Contact numbering (5)Appendix 1.2. – Gecko with Latches Contact numbering (5)Appendix 1.3. – Gecko-MT Part Numbering (6)The G125 series of connectors (branded “Gecko”) comprises of: barrel crimp contacts and crimp housings available in Male and Female genders; Vertical and Horizontal PC-Tail Connectors and Vertical Surface Mount Connectors; all on a 1.25mm pitch. Connectors are fully shrouded, unsealed connectors for interconnecting cable-to-cable, cable-to-board and board-to-board applications.The Gecko Crimp variants are fully shrouded, unsealed connectors with replaceable contacts. They are designed for interconnecting cable-to-cable and cable-to-board. The housings have a low profile potting wall to allow back potting for additional strain relief and improved sealing where required. All pre-made cable assemblies are supplied back-potted for customer convenience, and individually crimped contacts are also available.There are three variants of the range, the ranges are not intermateable:•Gecko-SL – Screw-Lok version. Female connectors have floating screws for secure, robust interconnection to the male counterpart. Male Screw-Loks can also have board-mount studs forsecure PCB connection.•Gecko with Latches (original design). Male variants can be equipped with locking latches for secure interconnection with easy to release features. Latches can be specified with through board locking features or surface mount pads for additional security.•Gecko-MT. Connectors are equipped with both signal and power contacts and are available in crimped or through-board configurations. Screw-Lok technology is used to secure the connectors,and board-mount studs for PCB fastening are available.All contacts are gold plated all over for high performance and long service life; the contact plating is hard acid gold of 98% purity.The Gecko-SL and latched ranges cover 06, 10, 12, 16, 20, 26, 34 and 50 total number of contacts in a dual row configuration. Connector housings are polarised to prevent mis-matching and have contact position one indicated on the outside of the housings. Metal backshells are available for sizes 06, 10, 12 and 16 cable variants in the Gecko-SL range, to provide mechanical, RF and EMC protection. Gecko-MT connectors are available in ’01-08-01’ and ’02-08-02’ configurations, with 2 power contacts and 8 signal contacts or 4 power contacts and 8 signal contacts respectively.2. RATINGS2.1. MATERIALSAll materials are also listed on individual drawings.All Power Contacts ..................................................................... B eryllium CopperAll Female Signal Contacts ......................................................... B eryllium CopperMale PCB Signal contacts ........................................................... P hosphor BronzeMale Crimp Signal Contacts ........................................................ B rassContact plating finish ................................................................. H ard Gold over NickelHousing ....................................................................................... 30% Glass Filled Thermoplastic UL94 V-0 Latches ........................................................................................ C opper-Nickel-Tin alloy, Tin over NickelfinishScrew-Lok fixings ....................................................................... S tainless SteelMetal Backshells ......................................................................... A luminium 6061-T6, High PhosphousNickel finishPotting Compound ...................................................................... S tycast 2651MM with Catalyst 92.2. ELECTRICAL CHARACTERISTICSEIA-364-70A: 1998 – Current – per individual signal contact, 25°C ambient .................. 2.8A max(When only one contact per connector is electrically loaded)EIA-364-70A:1998 – Current – per track for Flex Circuits, 25°C ambient…………………….0.4A maxEIA-364-70A: 1998 – Current – per signal contact through all contacts, 25°C amb. ....... 2.0A maxEIA-364-70A: 1998 – Current – per power contact through all contacts ......................... 10.0A max2.2. ELECTRICAL CHARACTERISTICS (CONT.)EIA-364-20C: 2004 – Voltage Proof (at 1013mbar, sea level) .............................. 600V DC or AC peak EIA-364-20C: 2004 – Voltage Proof (at 44mbar, 21,336m/70,000ft) ................... 350V DC or AC peak Working Voltage (at 44mbar, 21,336m/70,000ft)…………………………. .................. 250V DC or AC peakWorking Voltage (at 1006mbar, sea level)………………………………. ....................... 450V DC or AC peakEIA-364-06C: 2006 – Contact Resistance (initial) ................................................. 20mΩ maxEIA-364-06C: 2006 – Contact Resistance (after conditioning) ............................. 25mΩ maxEIA-364-21C: 2000 – Insulation Resistance (initial) .............................................. 10GΩ min at 500V DCEIA-364-21C: 2000 – Insulation Resistance (after conditioning*) ........................ >1GΩ min at 500V DCCreepage Distance (contact-to-contact) ................................................................ 0.15mm minClearance Distance (contact-to-contact) ............................................................... 0.15mm min*excluding Salt Mist conditioning2.3. ENVIRONMENTAL CHARACTERISTICSEIA-364-31B: 2000 - Humidity ................................................... 65/150/56 days at 93% RHEIA-364-32C: 2000– Temperature Range ................................. T est Condition IV, Dwell 30mins, 5 cyclesat -65°C to +150°CEIA-364-17B: 1999– Temperature Life ...................................... T est Condition X, 150°C±5°C, Method A,without loadEIA-364-26B: 1999 – Salt Mist .................................................. T est Condition B, 48 hours continuousexposureEIA-364-28D: 1999 – Vibration Severity ◊● .............................. T est Condition IV: 10Hz to 2000Hz,1.5mm,198m/s² (20G) Duration = 2 Hours EIA-364-27B: 1996 – Shock Severity ◊ ●............................... T est Condition E: 981m/s² (100G) for 6msin Z axis, 490m/s² (50G) for 11ms in X & YaxesBump Severity ◊......................................................................... 390m/s² (40G), 4,000±10 BumpsEIA-364-01A: 2000 – Acceleration Severity .............................. 490m/s² (50G)◊Latches or Screw-Loks fully utilizedX&Y tested at lower levels due to shaker limitations● It is recommended that back-potting compound is applied to crimp assemblies for vibration athigher frequencies2.4. MECHANICAL CHARACTERISTICSDurability ................................................................................................................. 1000 operationsDurability (Latches) ................................................................................................ 100 operations By hand or with Z125-926XX00 tools. Minimum added retention of 20NScrew-Lok Torque ................................................................................................... 16 to 18 cmNScew-Lok Retention in Housing ............................................................................. 20.0N minContact Retention in Housing (all contact types) ................................................. 6.0N minSignal Insertion Force (per contact, using mating contact) .................................. 2.8N maxSignal Withdrawal Force (per contact, using mating contact) ............................. 0.2N minPower Insertion Force (per contact, using mating contact) ................................. 7.0N maxPower Withdrawal Force (per contact, using mating contact) ............................. 0.2N minLatch Retention in Housing .................................................................................... 4.0N min2.5 WIRE TERMINATION INFORMATION – SIGNAL CRIMP PRODUCTSWire Type (recommended) .............................................BS 3G 210 type A, MIL-W-16878/6 type ET orNEMA HP3 type ETMaximum Insulation Diameter .......................................Ø0.80mmInsulation Strip Length ....................................................1.50-1.75mmRecommended Hand Crimp Tooling ...............................Hand Crimp Tool Z125-900, Positioner Z125-901,Insertion/Removal Tool Z125-902 Recommended potting compound is Stycast 2651MM with Catalyst 9.Wire Size (AWG)Stranding(No. x Ømm)Diameter(mm) Area (mm²)Circular MILArea (CMA)Crimp ToolSettingCrimp Height(mm)Min. pull-offforce (N)26 7 x 0.15 Ø0.533 0.128 253 60.95-1.10 1828 7 x 0.13 Ø0.381 0.072 159 5 1330 7 x 0.10 Ø0.305 0.057 100 5 1232 7 x 0.08 Ø0.203 0.035 62 5 6For information on crimping Gecko signal contacts refer to Tooling Instruction Sheet IS-37. Forinformation on insertion/removal of Gecko signal cable contacts refer to Tooling Instruction Sheet IS-38. There is also a Video on crimping and inserting Gecko contacts: https:///harwintv2.6 WIRE TERMINATION INFORMATION – POWER CRIMP PRODUCTSWire Type (recommended) .............................................M22759/11-18 PTFE (MIL-W-22759/11)Maximum Insulation Diameter .......................................Ø1.35mmInsulation Strip Length ....................................................1.90-2.30mmRecommended Hand Crimp Tooling ...............................Hand Crimp Tool Z125-903, Positioner Z125-904,Insertion/Removal Tool Z125-905 Recommended potting compound is Stycast 2651MM with Catalyst 9.Wire Size (AWG) Stranding(No. x Ømm) Diameter(mm)Area(mm²)Circular MILArea (CMA)Crimp ToolSetting (N)18 19 x 0.25 Ø1.250 0.930 1624 8 85 For information on crimping Gecko-MT power contacts refer to Tooling Instruction Sheet IS-44. For information on insertion/removal of Gecko power contacts refer to Tooling Instruction Sheet IS-47. There is also a Video on crimping and inserting Gecko contacts: https:///harwintvAPPENDIX 1 APPENDIX 1.1. – GECKO-SL CONTACT NUMBERING Female Crimp Housing Male Crimp Housing Female PCB mounted Male PCB mounted APPENDIX 1.2. – GECKO WITH LATCHES CONTACT NUMBERING Female Crimp Housing Male Crimp Housing Female PCB mounted Male PCB mounted No. 1 Contact mark15 1 1 1 5 5 56 6 6 6 10 10 10 10 No. 1 Contact markNo. 1 Contact mark 1 6 7 12 1 6 7 12 1 6 7 12 1 6 7 12APPENDIX 1.3. – GECKO-MT CONTACT NUMBERING Female PCB mounted (01-08-01) No. 1 Contact mark 1 4 5 8 A B Female Crimp Housing(01-08-01) 1 4 5 8 A B Male PCB mounted (02-08-02) A 4 1 85 B C DMale Crimp Housing (02-08-02) 4 1 8 5 A B C DG125-FS12005F3P G125-3241096M2G125-FS11005F3PG125-MV12005M3 P G125-MV12605M1PG125-FC11605F1-0150LG125-FC12605F1-0450LG125-FC13405F1-0150L。
人脸门禁一体机目录第1章注意事项 (7)第2章概述 (10)2.1产品简介 (10)2.2产品功能 (10)第3章外观介绍 (12)3.1尺寸（mm） (12)3.2外观图 (13)第4章安装说明 (14)4.1安装环境 (14)4.2安装步骤 (14)第5章接线说明 (16)5.1 接线端子说明 (16)5.2 接口应用说明 (17)第6章设备激活 (18)6.1 通过本地设备激活 (18)6.2 WEB激活 (18)6.3 修改设备IP (19)第7章WEB端操作说明 (20)7.1 登录 (20)7.2 预览 (20)7.3 回放 (23)7.4 日志查询 (26)7.5 配置 (26)7.5.1 常用设置 (27)7.5.2.1 音视频参数-视频参数 (30)7.5.2.2 音视频参数-音频参数 (32)7.5.2.3 音视频参数-图像设置 (33)7.5.3 网络设置 (37)7.5.3.1 基本设置 (37)7.5.3.2 高级设置 (40)7.5.4 报警设置 (47)7.5.4.1 报警管理 (47)7.5.5 门禁管理 (50)7.5.5.1 人员管理 (50)7.5.5.2 数据管理 (57)7.5.5.3 计划模板 (59)7.5.6 存储 (61)7.5.6.1 录像策略 (61)7.5.6.3 磁盘管理 (63)7.5.6.4 网络存储 (64)7.5.7 系统设置 (67)7.5.7.1 系统设置 (67)7.5.7.2 用户管理 (69)7.5.7.3 系统维护 (70)7.5.7.4 本地设置 (73)第8章设备本地操作 (75)8.1 激活及管理员登录 (75)8.1.1激活 (75)8.1.2管理员登录 (76)8.2 通讯设置 (78)8.2.2 韦根设置 (80)8.3 用户管理 (80)8.3.1 添加用户 (80)8.3.2 添加用户卡片 (82)8.3.3密码设置 (83)8.3.4 添加用户人脸 (84)8.3.5设置认证方式 (84)8.4 数据管理 (86)8.5 记录查询 (87)8.5.1 记录查询 (87)8.5.2 事件查询 (88)8.6 门禁设置 (89)8.7 系统设置 (90)8.7.1 系统信息 (91)8.7.2 人脸参数 (92)8.7.3 时间设置 (93)8.8 系统信息 (94)8.8.1 记录容量 (95)8.8.2 设备信息 (95)第9章人脸录入注意事项 (96)9.1 人脸照片录入要求 (96)9.2 人脸姿态 (96)9.3 人脸录入位置 (97)第十章公司声明 (98)附录一外置读卡器使用说明 (99)第1章 注意事项欢迎您选购我司的产品，如果您在使用中遇到任何疑问，请向经销商或我司售后服务咨询。
lssued date: 2014/05/30 Model NO: EYA-01200010开关电源供应器承认规格书Switching power supply specification1.总则2.电气特性2.1输入特性2.1.1输入电压2.1.2输入频率2.1.3输入电流2.1.4输入冲击电流2.1.5功率因数2.1.6保护功能2.1.7保护功能2.2 输出特性2.2.1输出电压2.2.2输出负载2.2.3输出功率2.2.4输出调整率2.2.5保护功能2.2.6输出电压纹波及噪音2.2.7过冲3.环境要求3.1 温度范围3.1.1工作温度3.1.2储存温度4.安全要求4.1 高压测试4.2 漏电流4.3 电磁兼容5.机械特性5.1 外型尺寸1.总则本规格书定义数码技术设备采用的12W交流适配器规格的要求，该电源适配器是将交流市电变换为连续稳定的直流电压+12V的开关电源，具有输入电压范围宽，输出过压短路保护功能2.电气特性2.1 输入特性2.1.1输入电压范围额定输入电压范围：100-240V AC工作输入电压范围：90-260V A2.1.2输入频率电压频率：47-63HZ2.1.3输入电流最大输入电流≤0.3A2.1.4输入冲击电流冲击电流≤10A2.1.5功率因数功率因数≥0.52.1.6整机效率效率≥75%2.1.7保护功能2.1.7.1欠压保护当电压低于2.1.1部分规定的最小输入电压，不会导致适配器任何损坏2.1.7.2突发性故障保护适配器的任何元件失效，均不产生下列现象A.巨大爆炸的响声B.火焰C.浓烟D.引发人身安全的漏电2.2 输出特性2.2.1输出电压输出电压范围：12V±5%2.2.2输出负载最少负载：0A额定负载：1A最大负载：1.2A2.2.3输出功率额定功率：12W最大功率：14.5W2.2.4输出电压调整率在2.1.1所叙输入条件下，2.2.2部分所叙输出电压均符合2.2.1部分规定。
EXC1414 x 38 mm EV fuseProduct features• 14 x 38 mm fuse• Current rating: 50 A to 80 A• 800 Vdc rating• High breaking capacity for high energy applications• Designed to JASO D622, ISO8820-8,GB/T31465• Produced in a factory with ISO9001 &IATF16949 certification• Minimum breaking capacity 300% In at rated DC voltage• Bolt-down terminal and PCB terminal options Applications• Automotive and commercial grade on-board chargers• Uninterruptible power supplies (UPS)• 3-phase EVSE and charging infrastructure • Motor protection• Rectifiers and inverters• Energy storage systems• On-board electric vehicle powertrain and distributionAgency informationUL (RU) recognition file number: E532712Environmental complianceHALOGENHFFREEOrdering part numberPbEXC14-50-SCTFamily codeAmpere rating (50 = 50 A)Option codeOption code3P=3 pin PCB terminalSCT= Bolt down single cap2Technical Data ELX1311Effective May 2023EXC1414 x 38 mm EV fuse/electronicsElectrical characteristicsAmps (A)Minimum (seconds)Maximum (seconds)3.0 In 0.115Product specificationsRated current Typical cold resistance 1Typical voltage drop ***************Part number Rated voltage (A)Breaking capacity(mΩ)(mV)(W)EXC14-50800 Vdc 50800 Vdc/50 kA 1.95150 1.6EXC14-60800 Vdc 60800 Vdc/50 kA 1.59140 1.65EXC14-70800 Vdc 70800 Vdc/50 kA 1.24160 1.8EXC14-80800 Vdc80800 Vdc/50 kA1.051502.0SCT: Bolt-down terminal single cap3P: 3 pin PCB terminalPCB layout 3P: 3 pin PCB terminal1. Cold resistance is measured at <10% In and +25 °C ambient temperatureDimensions- mmTolerances unless otherwise specified One place x.x = ± 0.3 mm Two places x.xx = ± 0.13 mmPart markingNote: recommend tightening torque is 4.5+/-1.0 Nm for M5 screw3Technical Data ELX1311Effective May 2023EXC1414 x 38 mm EV fuse /electronics TerminalsInner packageShip packageSCT 12 pieces/box 324 pieces/box 3P10 pieces/box240 pieces/boxPackaging informationGeneral specificationsOperating temperature: -40 °C to +125 °C with proper derating factor applied Strength of terminals: JASO D622 6.3.9, mounting torque 4.5 +/-1 Nm, 3 timesTemperature humidity cycling: JASO D622 6.3.4.1,a) maintain the samples at standard conditions for 4 hours b) increase T to 55 +/-2 °C at 95% to 99% RH within 0.5 hours c) maintain T at 55 +/-2 °C at 95% to 99% RH for 10 hoursd) decrease T to -40 +/-2 °C within 2.5 hours; the humidity is uncontrolled e) maintain T at -40 +/-2 °C for 2 hours; the humidity is uncontrolledf) increase T to 120 +/-2 °C within 1.5 hours from -40 +/-2 °C; the humidity is uncontrolled g) maintain T at 120 +/-2 °C for 2 hours; the humidity is uncontrolledh) allow to return to RT within 1.5 hours; the humidity is uncontrolled 10 cycles.Thermal shock: ISO8820-8 GB/T31465.6, 48 cycles; -40 °C to 100 °C, each cycle 60 minutes Vibration: JASO D622 6.3.3, 10-55 Hz, 3 directions, 2 hours each directionTransient current cycling: JASO D622 6.3.2 (reference), The transient current start from 2.0 In for 0.25 seconds, then drop to 0.5 In and keep this cur-rent to 15 seconds to finish one cycle, total 50000 cyclesLubricant & fuel oil resistance: GB/T31465.1-5.4, Wipe the marking with lubricant or oil 30 seconds4Technical Data ELX1311Effective May 2023EXC1414 x 38 mm EV fuse/electronics0.40.50.60.70.80.911.11.21.3-50-40-30-20-10102030405060708090100110120130140T emperature derating curveCurrent vs. time curve 0.010.111010010100100010000T i m e (s )50A Current (A)80A70A 60A D e r a t i n g f a c t o rT emperature (°C)I 2T vs. time curve1001,00010,000100,0001,000,00010,000,000100,000,0000.0010.010.11101001000I 2t (A 2s )50ATime (s)70A 80A 60A5Technical Data ELX1311Effective May 2023EXC1414 x 38 mm EV fuse /electronics I 2t vs. current curve1001,00010,000100,00010010,000I 2t (A 2s )80A70A50A1,000Current (A)60AEatonElectronics Division 1000 Eaton Boulevard Cleveland, OH 44122United States/electronics© 2023 EatonAll Rights Reserved Printed in USAPublication No. ELX1311 BU-ELX22174May 2023EXC1414 x 38 mm EV fuseTechnical Data ELX1311Effective May 2023Life Support Policy: Eaton does not authorize the use of any of its products for use in life support devices or systems without the express writtenapproval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.Eaton reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Eaton also reserves the right to change or update, without notice, any technical information contained in this bulletin.T e m p e r a t u r eTimeT T T T Wave solder profile--PCB version onlyReference EN 61760-1:2006Profile featureStandard SnPb solderLead (Pb) free solderPreheat • Temperature min. (T smin )100 °C 100 °C • Temperature typ. (T styp )120 °C 120 °C • Temperature max. (T smax )130 °C 130 °C • Time (T smin to T smax ) (t s )70 seconds 70 seconds ∆ preheat to max Temperature150 °C max.150 °C max.Peak temperature (T P )*235 °C – 260 °C 250 °C – 260 °C Time at peak temperature (t p )10 seconds max5 seconds max each wave 10 seconds max5 seconds max each wave Ramp-down rate~ 2 K/s min ~3.5 K/s typ ~5 K/s max ~ 2 K/s min ~3.5 K/s typ~5 K/s max Time 25 °C to 25 °C4 minutes4 minutesManual solder+350 °C (4-5 seconds by soldering iron), generally manual/hand soldering is not recommended.Eaton is a registered trademark.All other trademarks are property of their respective owners.Follow us on social media to get the latest product and support information.。
Sinteso™ 产品目录1. 火灾报警控制器 (1)FS1120 CI1142/S/H47 智能感知型系统控制器 (1)FS1120 CC114x-CT/S/H67 智能感知型系统控制器 (2)FS1120 CI1142/S/Rack 智能感知型系统控制器（上柜式） (3)FS1120 CC114x-/S/Rack 智能感知型系统控制器（上柜式） (4)S11/EU消防辅助设备扩充机柜（上柜式） (5)2. Sinteso智能感知型探测设备 (6)FDO221-CN 光电感烟探测器 (6)FDT241-CN 感温探测器 (7)FDOOT241-CN 烟温复合型探测器 (8)FDB221 探测器底座 (9)FDB222 探测器底座（薄型） (9)FDSB291-CN 蜂鸣器底座 (10)FDM229-CN 手动报警按钮（碎玻式） (11)FDM228-CN 手动报警按钮（可复位式） (12)FDHM228-CN 消火栓报警按钮（可复位式） (13)FDCI225-CN 输入模块（4路） (13)FDCO224-CN 输出模块（4路） (14)FDCIO223-CN 输入输出模块（2路） (15)FDCL221-CN 线路隔离模块 (16)3. 通用产品 (17)OP520光电感烟探测器 (17)HI520电子感温探测器 (17)SO520非编址探测器底座 (17)DO1101A-Ex 集合型光电感烟探测器（防爆型） (18)DT1101A-Ex 集合型电子感温探测器（防爆型） (18)DB1101A 集合型探测器底座 (18)FDL241-9-CN 线型光束感烟探测器 (19)FDLB291 线型光束感烟探测器底座 (19)DLR1191 三棱反射镜 (20)DLR1192 反射板 (20)DLR1193 反射板 (20)DLH1191A 三棱反射镜加热元件 (20)FDF241-9 红外火焰探测器 (21)FDFB291底座 (22)DF119X防雨罩 (22)MV1 红外火焰探测器安装支架 (22)MWV1 红外火焰探测器球窝铰链 (22)SB3 防爆隔离栅 (23)EOL22（EX）非编址回路终端电阻（防爆型） (23)4. 控制器功能扩展部件 (25)E3M140 FDnet回路卡 (25)E3M080 非编址回路卡 (25)E3L020 输入输出联动卡（16路） (25)E3I040 层显转换卡（LON总线） (26)E3I020 RS232通讯卡 (26)K3I050显示驱动卡 (26)E3G070 通用控制卡 (27)E3G080灭火控制卡 (27)E3H020 网络通讯卡 (28)E3X102 主CPU卡 (28)E3X103 主CPU卡 (28)B3Q565 操作显示终端 (29)TPS11R 打印机（用于上柜式控制器） (29)TPS11W 打印机（用于壁挂式控制器） (29)FC9342 联动控制盘 (30)5. 辅助设备 (31)HY2114 警铃 (31)HSG1010 声光报警器 (31)BN3002C 吸顶式音箱 (32)ZA2725A 壁挂式音箱 (32)HGM2100-24 应急广播控制器 (33)HGM2425 广播功率放大器（250W） (34)HD210 火警电话分机 (35)HD220 手提火警电话 (36)HD230 电话插孔 (36)HDM2100-24 多线式火警通讯盘24路 (37)HY5711B 总线式火警通讯盘 (38)HY5714B总线式火警电话插孔 (39)HY5716B总线式火警电话分机 (39)BCH1936 立柜（带玻璃门） (40)BCH1950 双琴台 (40)BCB8005壁挂电源8A (41)BCB8002上柜电源20A (41)BCB8003上柜电源30A (42)ZA1952/15浮冲备用电池 (42)ZA1952/24浮冲备用电池 (42)ZA1952/38浮冲备用电池 (42)NP24-12 24AH/12V 电池 (42)NP38-12 38AH/12V 电池 (42)附件1 Sinteso智能感知型火灾自动报警及联动控制系统设计参考 (43)附件2 火灾报警系统的安装指南 (52)型号功能描述/技术参数部件号设备外观1. 火灾报警控制器FS1120CI1142/S/H47100720588FS1120 CC114x-CT/S/H67100720589FS1120CI1142/S/Rack100720590FS1120 CC114x-/S/Rack100720591S11/EUBCH1950或BCH1936 100673990型号功能描述/技术参数 部件号 设备外观FDO221-CN-10... +60 -30... +75 2. Sinteso 智能感知型探测设备100718388型号功能描述/技术参数部件号设备外观FDT241-CN100718389200+50-25...-25...+70-30...+75FDOOT241-CN100718390280+70-25...-30...+751...20FDB221 FDB222FDB221 探测器底座（瑞士生产）●可编址探测器底座，明装或暗装形式均适用。
