常用塑料英文单词嵌件---insert嵌件销---insert pin气胀真空成形---air assist forming空气隙---air gap空气顶出---air ejection永久伸长---permanent elongation,tension set永久变形---permanent set,permanent deformation蚀刻,侵蚀---etching应力---stress应力松弛---stress relaxation应力龟裂---stress cracking应力集中---stress concentration应力断裂,应力破坏---stress rupture应力.应变曲线---stress-strain curve应力.应变图---stress-strain diagram托板,模板---retainer plate硬度---hardness合模机构---mold clamping mechanism合模力,闭模力---locking force,clamping force开模力---mold opening force悬臂梁---cantilever beam润滑剂---lubricant模具---mold,Tools,Tooling模温度控制器---mold temperature controller模具尺寸---mold size加热管套(料筒)---heating cylinder加热板---heating plate凸轮---cam玻璃纤维---glass fiber,fibrous glass玻璃纤维强化热塑塑料---fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP玻璃纤维强化塑料---glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP.感光聚合物---photopolymer,photo-sensitive polymer镜面抛光---mirror polishing龟裂---cracking龟裂---crack颗粒料---granule石墨---graphite石墨纤维---graphite fiber间隙, 隙距---clearance模蕊,蕊片,蕊线,蕊孔---core成孔销,模蕊销---core pin成孔销托板---core pin plate公差,容差---tolerance冷料---cold slug冷料井,冷料窝---cold slug well回程销,覆归销---surface pin冷热骤变试验---thermal shock test热应力龟裂---thermal stress cracking,TSC 侧向浇口---side gate侧向模蕊(心型)销---side draw pin砂磨---sanding喷砂,打砂---sand blast修饰,涂饰,打光---finishing自断浇口,剪切浇口---shear gate紫外线---ultraviolet, UV紫外线稳定剂---UV stabilizer紫外线吸收剂---UV absorber压花---embossing压花机---embossing machine喷霜,起霜---blooming exudation鲨皮斑---shark skin射出压力---injection pressure射出成形---injection molding射出成形机---injection molding machine 射出成形模具---injection mold射出装置---injection unit射出速度---injection speed射出喷嘴,注料嘴---injection nozzle射出容量---machine shot capacity射出率(量)---injection rate煮沸试验---boiling test充填不足,缺料---short shot手动模具---hand mold,loose mold手动油压机---hand press缩窝,凹孔---shrinkage pool冲击试验---inpact test冲击强度---impact strength烧结法,粉铸法---sintering烧结成形法---sinter molding模板---mold plate注射,射料---shot硅橡胶---silicone rubber真空成形---vacuum forming珠光颜料---pearlescent pigment浸渍涂装---dip coating人造皮革---artificial leather废料粉碎机---scrap grinder顶出板,脱模板---stripper plate应力龟裂---stress cracking环境应力龟裂试验---environmental stress cracking test行程,冲程---stroke注道,注道料---sprue注道衬套,浇口衬套---sprue bush成形压力,模制压力---molding pressure成形温度,模制温度---molding temperature成形循环,成形周期---molding cycle成形时间,模制时间---molding time成形收缩,模压收缩---mold shrinkage, molding shrinkage窄浇口,限制形浇口---restricted gate剪切强度,抗剪强度---shear strength增亮剂---brightening agent,optical brightener,optical whitening agent 加速试验---accelerated test加速老化---accelerated ageing塑性变形---plastic deformation塑性流动---plastic fiow翘曲---warp(ing),warpage抗臭氧性---ozone resistance抗臭氧试验---ozone resistance test耐天侯性---weatherability,weather resistance耐旋光性---light resistance,light fastness天侯老化试验---weathering test耐酸性---acid resistance耐冲击性---impact resistance褪色---fading,discoloration耐蚀性---corrosion resistance拉杆,导柱---tie-bar拉杆间距---tie-bar distance多模穴模具---multi-cavity mold双色射出成形---double-shot molding超音(声)波镶嵌---ultrasonic inserting超音(声)波焊接---ultrasonic welding顶出,脱模---ejection顶出组合---ejector顶出板---ejector plate,knock-out plate顶出杆,脱模杆---knock-out bar,ejector rod无光面---dull surface低压射出成形法---low pressure injection molding硬度计---durometer电镀---electroplating,electrodeposition电铸模具---electroformed mold尼龙,(聚酰胺树脂之俗称)---nylon尼龙纤维---nylon fiber扭曲试验---torsion test扭力矩---torsion moment喷嘴,注嘴---nozzle喷嘴接触---nozzle touching喷嘴止流---nozzle shut-off支管形喷嘴---nozzle manifold脱模销,顶出销---knock-out pin脱模销托板,顶出销托板---knock-out pin plate背压---back pressure止回阀,止逆阀---back pressure valve发泡剂---blowing agent,expanding agent发泡塑料,泡沫塑料---plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge抛光布轮---buff,buffing wheel布轮抛光---buffing毛边,整纹,溢料---flash,fin修边,除边---deflashing,definning修边机,修毛边机---deflasher手工脱模,手工顶出---hand ejection剥离,剥皮加工---peeling剥离试验---peeling test拉出成形---pultrusion凹痕,缩痕---sink mark,shrink mark抗刮硬度,刮痕硬度---scratch hardness非破坏性试验---non-destructive testing起泡,气泡---blister疲劳试验---fatigue test疲劳寿命---fatigue life疲劳强度---fatigue strength针眼,针孔---pinhole玻璃纤维强化,热塑塑料射出成形---fiberfil molding 起泡,气泡---blister底漆,底胶,引发剂---primer溢料---flash溢料缝,毛边槽---flash groove流痕---flow mark冷却线---frost line原型模,试验模---prototype mold环境温度---ambient temperature止流阀---shut-off valve孔隙,空洞,气泡---void放电---discharge全压式模具---positive mold辅助压缸---auxiliary cylinder烫印---hot stamping,roll leaf stamping弯曲龟裂---flex cracking磨损---abrasion,wear磨耗---abrasion loss莫斯硬度---Mohs’hardness退火---annealing回火---tempering杨氏弹性系数---Young’s modulus of elasticity油压增压器---hydraulic intensifier油压机---hydraulic press油压马达---hydraulic motor焊接---welding内衬,衬套,衬垫---liner流道,流道料---runner合模销,导销---leader pin合模销套,导销衬套---leader pin bushing回程销, 覆归销---return pin冷却水通路---cooling channel常温成形,冷模压---cold molding老化试验---ageing test对位圈,定位环---locating ring熔合线,结合线---weld line肉厚---wall thickness脱模斜度---draft angle母模---cavity side顶出销,顶针---ejector pin分模线---parting line浇口,灌点---gate竖浇道---sprue浇道,流道---runner模仁,雄模,模心---core side浇口白晕---gate bush凹痕,缩痕,缩水---sink mark银线---silver line隧道形浇口---tunnel gate沉陷式浇口,潜入式浇口---submarine gate针孔形浇口---pin point gate注道形浇口,直接浇口---sprue gate毛边形浇口,薄膜形浇口---flash gate,external ring gate,internal ring gate 喷流,喷射现象---jetting剥料板---stripper plate。
