Declaration of Conformity

declaration of conformity模板Declaration of Conformity[Your Company Logo]Declaration of ConformityDate: [Insert date]To whom it may concern,Subject: Declaration of Conformity for [Product Name/Model Number]We, [Your Company Name], hereby declare that the product [Product Name/Model Number] complies with all relevant regulations, standards, and directives.1. Identification of the Product:- Product Name: [Product Name]- Model Number: [Model Number]- Serial Number: [Serial Number]- Brand: [Brand]- Manufacturer: [Your Company Name]- Address: [Your Company Address]2. Relevant Standards and Directives:- The product [Product Name/Model Number] has been designed, manufactured, and tested in accordance with the following applicable standards and directives:- [List all relevant standards and directives]- The conformity assessment procedures in accordance with the relevant standards and directives have been carried out by [Your Company Name].3. Description of the Product:- [Provide a brief description of the product, its features, and its intended use.]4. Technical Specifications:- [List the technical specifications of the product, such as dimensions, weight, power requirements, etc.]5. Test Reports and Certification:- [Describe any test reports or certifications obtained for the product and their corresponding reference numbers.]6. Compliance with Safety Regulations:- [Explain how the product complies with safety regulations and any safety features implemented.]7. Compliance with Environmental Regulations:- [Explain how the product complies with environmental regulations, including proper disposal and recycling instructions.]8. Authorization:- [Insert the name and position of the authorized person signing the declaration.]- [Add the signature of the authorized person.]- [Include the company seal or stamp, if applicable.]9. Contact Information:- For further information or inquiries regarding this Declaration of Conformity, please contact:[Your Company Name][Contact Person][Address][Phone Number][Email Address]We hereby confirm the compliance of the product [Product Name/Model Number] with the relevant regulations, standards, and directives. This Declaration of Conformity remains valid unless any modifications are made to the product that might affect its compliance.Yours sincerely,[Your Company Name][Authorized Person's Name and Position]。

ce自我声明型证书流程CE自我声明型证书流程CE自我声明型证书是指根据《欧洲共同体实施规则》（EU implementation regulations）的要求，企业自行对产品进行符合CE认证要求的自我审查，并签署自我声明（Declaration of Conformity）证明产品符合相关的欧洲指令和标准。

CE自我声明型证书的发放是为了方便企业自身的产品审核，而无需通过第三方认证机构的参与。

下面将一步一步回答CE自我声明型证书流程。

1. 了解CE认证要求和相关指令CE认证是指根据欧洲联盟制定的一系列的产品安全、环保和技术要求进行的认证。

在开始自我声明流程之前，企业应首先了解与其产品相关的CE 认证要求和相关的指令，确保对产品的技术规范和测试方法有清晰的了解。

2. 自我评估和检查企业接下来需要对其产品进行自我评估和检查，确保其符合CE认证要求。

这涉及到对产品的结构、性能、材料、安全性、电磁兼容性、环境影响等多个方面进行评估和检查。

此外，还需要对产品进行必要的实验室测试和技术文件的准备。

3. 编写技术文件技术文件是CE自我声明型证书的重要组成部分，它记录了产品的技术规范、测试结果、制造过程、品质控制等信息。

企业应编写完备、准确的技术文件，确保其符合相关指令的要求。

4. 编写自我声明自我声明是企业对产品的自我证明，它包含了产品符合相关CE指令和标准的声明。

自我声明需要简洁、明确地声明产品的相应符合情况，并由企业负责人或授权的代表签名确认。

5. 发布CE自我声明型证书当所有准备工作完成后，企业可以将自我声明和技术文件整理成电子或纸质形式，并发布CE自我声明型证书。

企业应确保该证书的真实性、准确性和可追溯性，以满足相关的合规要求。

6. 产品上市和市场监管一旦获得CE自我声明型证书，企业就有资格将其产品投放市场。

然而，需要注意的是，CE标志仅表示产品符合欧洲标准，而不代表质量、品牌或可靠性的保证。

因此，企业应继续对其产品进行监管，确保符合相关法规和标准的要求。

declaration of conformity模板Declaration of Conformity Template[Your Company Name][Your Company Address][City, State, Zip Code][Country][Email Address][Phone Number][Website]DECLARATION OF CONFORMITYProduct Information:Product Name: [Product Name]Model Number: [Model Number]Serial Number: [Serial Number]Batch Number: [Batch Number]Manufacturer: [Your Company Name]Intended Use: [Brief description of the product's intended use] Standard: [Applicable standard or regulation]We, [Your Company Name], declare under our sole responsibility that the above-mentioned product is in conformity with the essential requirements of the applicable standard or regulation as stated above.This declaration is based on the following:1. Testing and examination of representative samples.2. Collecting technical documentation and specifications of the product.3. Evaluating and assessing the conformity of the product.4. Ensuring compliance with relevant provisions of the applicable standard or regulation.This product complies with the essential requirements related to safety, electromagnetic compatibility, and environmental protection, as defined in the applicable standard or regulation.Technical Documentation:The technical documentation regarding the design, manufacturing, and operation of the product is available at our premises. It includes the following information:1. Product design specifications, including drawings and schematics.2. Bill of materials (BOM) with the list of components, materials, and their specifications.3. Manufacturing processes, including quality control procedures.4. Test reports and test results conducted to assess compliance with the applicable standard or regulation.5. User manual and relevant instructions for safe and proper use of the product.6. Warranty and support information.This Declaration of Conformity remains valid as long as no changes are made to the product design, manufacturing processes, or components that could affect its compliance with the applicable standard or regulation.[Your Company Name] is committed to maintaining the conformity of this product and taking the necessary measures to address any non-conformities that may arise. We ensure that all products placed on the market under our brand name meet the required standards and regulations.Date:[Date of declaration]Signature:[Authorized signature]Printed Name:[Printed name of the authorized person]Title:[Job title of the authorized person]Note: This document is provided in English [or language of choice]. In case of any discrepancies or ambiguities arising from translations, the English version shall prevail.Please note that this is a suggested template for a Declaration of Conformity. It is important to consult the applicable regulations and standards specific to your industry and product to ensure compliance.。

declaration of conformity模板Declaration of Conformity[Your Company Name][Your Company Address][City, State, ZIP Code][Date]Subject: Declaration of Conformity for [Product Name/Model Number]To whom it may concern,We, [Your Company Name], hereby declare that the [ProductName/Model Number], manufactured and supplied by us, complies with all relevant regulations and standards according to the following:1. Product Information:- Product Name: [Product Name/Model Number]- Manufacturer: [Your Company Name]- Manufacturing Date: [Date]- Batch/Serial Number: [Batch/Serial Number]2. Applicable Standards:- [List of applicable standards and regulations that the product complies with]3. Technical Specifications:- [Detailed technical specifications and features of the product]4. Testing and Certification:- The product has been tested in accordance with [relevant testing methods] to ensure compliance with the applicable standards.- [Certification Body] has issued the necessary certifications and test reports, which are available upon request.5. Compliance with Regulations:- The [Product Name/Model Number] complies with all relevant regulations and directives, including but not limited to:a) [List applicable regulations and directives, e.g., European Union CE marking]b) [Specify any specific requirements or certifications, if applicable]6. Safety and Environmental Considerations:- The [Product Name/Model Number] has been designed, manufactured, and tested to meet all safety requirements and minimize any potential environmental impact.- [Provide details of any safety features or eco-friendly initiatives implemented in the product]7. Responsible Party:- [Your Company Name] assumes full responsibility for the design, manufacturing, and conformity of the [Product Name/Model Number].- Point of Contact: [Name], [Job Title]- Email: [Email Address]- Phone: [Contact Number]This Declaration of Conformity is issued under our sole responsibility and in accordance with the relevant regulations and standards. It is valid for the specified product and remains in effect until any significant changes occur, or the product is discontinued from production.We hereby declare that all the information provided in this declaration is true, accurate, and complete to the best of our knowledge.Sincerely,[Your Name][Your Title/Position][Your Company Name]。

DECLARATION OF CONFORMITY我，(制造商名称) xxxx电气有限公司公司声明，(生产厂名称) xxxx电气有限公司生产的(详细填写产品名称、规格/型号) 动力柜SDXL主母线:In=630A～100A,Icw=10kA;Ue=380V,Ui=660V;50Hz;IP30符合如下要求：a) 中华人民共和国国家标准：____GB7251.1-2005_b) 其它相关标准或规定：_____________________________________________我公司对上述声明完全负责。

We,(manufacturer’s name)_ _ declare under our sole responsibility that the product (detailed description of product including name type or model)_________ ______ product in (factory’s name and address): _ _________ to which this declaration relates is in conformity with:a) GB standards; _b) And ot her standards and/or regulation________________________ _____________________(签署时间及地点) (负责人签名)(Place & Date of issue) (Name & Signature)DECLARATION OF CONFORMITY我，(制造商名称) xxx电气有限公司公司声明，(生产厂名称) xxxx电气有限公司生产的(详细填写产品名称、规格/型号) GGD主母线:In=1600A～630A,Icw=30kA;配电母线:In=630A,Icw=30kA;Ue=380V,Ui=660V;50Hz;IP30符合如下要求：a) 中华人民共和国国家标准：____GB7251.1-2005 _b) 其它相关标准或规定：_____________________________________________我公司对上述声明完全负责。

NumberK86656/02IssuedJuly 9th, 2015ValidJuly 10th, 2016Declaration of Conformity,based on parts of UL subject 2775, regardingDSPANon-Pressurized Condensed Aerosol Generators andComponentsKiwa Nederland B.V.Groningenweg 10Postbus 2562800 AG GoudaTel. +31-182-820460Fax +31-182-820465Internet www.kiwafss.nlCompanyDSPA B.V.Hulzenseweg 10-206534 AN NIJMEGENP.O. Box 65726503 GB NIJMEGENThe NetherlandsTel. +31 24 352 25 73Fax +31 24 37 87 583www.dspa.nlThis declaration consists of 11 pages.Publication of the declaration is allowed.Note: Publication of only this front page or parts of the declaration is considered as “not valid”.Underwriters Laboratories (or UL in short) was not involved with the performed tests asmentioned in this product declaration.STATEMENT BY KIWAWith this declaration, Kiwa declares that legitimate confidence exists that theproducts supplied byDSPA B.V.complying with the technical specifications as laid down in this productdeclaration and marked with the Kiwa®-mark in the manner as indicated inthis product declaration.Bouke MeekmaKiwaDeclarationThis product declaration by Kiwa is based on test protocol PRO10-001-AFG-nk rev 06 and parts of UL subject 2775.Please note that Underwriters Laboratories (or UL in short) was not involved with the performed tests as mentioned in this product declaration.Generator specificationsThe products mentioned below belong to this product declaration.DSPA 11-1, DSPA 11-2, DSPA 11-3, DSPA 11-4, DSPA 11-5, DSPA 11-6, DSPA 11-7 and DSPA 8-1.Type HousingRed coated steelActivationDSPA 11-1 Disk, radial, double shaped plate ElectricalDSPA 11-2 Disk, radial, double shaped plate ElectricalDSPA 11-3 Disk, radial, double shaped plate ElectricalDSPA 11-4 Disk, radial, double shaped plate ElectricalDSPA 11-5 Disk, radial, double shaped plate ElectricalDSPA 11-6 Disk, radial, double shaped plate ElectricalDSPA 11-7 Disk, axial, double shaped plate ElectricalDSPA 8-1 Cylindrical, axial ElectricalNon-pressurized generator.Application and useThis product declaration covers the construction and operation of condensed aerosol generators for total flooding applications when installed, inspected, tested, and maintained in accordance with the Standard for Fixed Aerosol Fire Extinguishing Systems, NFPA 2010. The fire extinguishing components shall be suitable for extinguishing fires of the following classes:•Class A according NFPA 2010•Class B according NFPA 2010•Class C according NFPA 2010Conditions for application•The numbers and types of the extinguishing components have to be determined in conformity with the guidelines and calculation methods of the supplier.•Distribution is to be done by supplier or companies authorised by the supplier.•Before usage an instruction is to be given by a trainer or instructor for this product authorized by the supplier.•The installation and maintenance of the fire extinguishing components have to take place according to the specifications of the supplier, NFPA 2010 or evaluation guideline BRL-K23003.Point of interest during use or limitation of useThe condensed aerosol extinguishing components should not be used on fires involving the following unless relevant testing by accredited testing laboratories has been carried out to the satisfaction of the Authority:•Deep seated fires in Class A materials•Certain chemicals or mixtures of chemicals material, such as cellulose nitrate and gunpowder, that are capable of rapid oxidation in the absence of air•Reactive metals such as lithium, sodium, potassium, magnesium, titanium, zirconium, uranium and plutonium.•Metal hydrides•Chemicals capable of undergoing auto thermal decomposition, such as certain organic peroxides and hydrazine•Condensed aerosol generators shall not be used to protect classified hazards or similar spaces containing flammable liquids or dusts that can be present in explosive air–fuel mixtures unless the generators are specifically listed for use in those environments. •Temperatures for use of aerosol extinguishing agents shall be within the supplier’s listed limits.•Unless specifically approved as an agent blend or mixture, systems employing the simultaneous discharge of different agents to protect the same enclosed space shall not be permitted.•Where unrelated extinguishing or suppression systems, such as a sprinkler system or a gaseous fire-extinguishing system are provided and can operate prior to or during the hold time of the aerosol system, the other agent shall not adversely affect the aerosol.The above list may not be exhaustive.•The design, installation, service, and maintenance of aerosol systems shall be performed by persons skilled in aerosol fire-extinguishing system technology.•Local applications 1) of condensed aerosol extinguishing systems are not covered by this product declaration.•Local applications require a pre-engineered and pre-designed system which has been tested and approved for a specific application by a authority such as Kiwa or by an accredited testing laboratory.1) a local application is used for the extinguishment of surface fires in flammable liquids, gasses, and shallow solids, where theenclosure does not conform to the requirements for total flooding.Owner’s manualAt delivery the product should be accompanied by an operation manual in the English language, known and authorized by Kiwa.Following minimum items shall be described according UL 2775:•Clear indication that it is not a detailed design, installation, operation, and maintenance instruction manual.•Clear reference to the availability of the design, installation, operation, and maintenance instruction manual by contacting the supplier.• A statement that periodic inspection is conducted by trained personnel.•Information regarding the essentials required to maintain the extinguishing system unit in operation both before and after a fire. •For extinguishing system units, a statement that no modifications are to be made to the extinguishing system unit without consultinga qualified designer who is to refer to the detailed design, installation, operation, and maintenance instruction manual. The statementshall include the following or equivalent wording: “This system is made up of units tested within limitations contained in the detailed design, installation, operation, and maintenance instruction manual.The designer must be consulted whenever changes are planned for the system or area of protection. An authorized installer or designer must be consulted after discharge”.Design, Installation, Operation, and Maintenance Instruction ManualAt delivery the product should be accompanied by an operation manual in the English language, known and authorized by Kiwa.Following minimum items shall be described according UL 2775:•Description of all variations of each unit, including the limitations for each variation;•Operating temperature range limitations;•Mass of aerosol-forming compound for each condensed aerosol generator size;•Discharge time for each condensed aerosol generator size;•Reference to the type of occupancy to be protected;•Reference to NFPA 2010, “Standard for Fixed Aerosol Fire Extinguishing Systems” for installation, inspection, testing, and maintenance requirements;•Material Safety Data Sheet (MSDS) information and cautionary instructions;•Description of the design procedure and typical layout with specific limitations and recommendations for correct installation and effective protection;•Specific information for condensed aerosol generator placement within the enclosure and orientation of discharge port(s); •Minimum safe distance between condensed aerosol generator discharge ports and personnel;•Minimum safe distance between condensed aerosol generator discharge ports and combustible materials;•Minimum safe distance between condensed aerosol generator casing and personnel;•Minimum safe distance between condensed aerosol generator casing and combustible materials;•Information on inspection after installation;•Description of requirements for maintenance of all equipment;• A list of part numbers for all replacement parts;•Useful life limitation for mandatory replacement of the condensed aerosol generators;•The name of the supplier or private labeller, or equivalent designation; and•Date and manual designation number on each page.•Description and operating details of each unit, mounting brackets, and all accessory equipment (as applicable), including identification by part or model number;•Degree and type of protection with associated design application densities for surface-type Class A and Class B fires including design application density limitations;•Condensed aerosol generator discharge port limitations, including maximum dimensional and area coverage, minimum and maximum height limitations, and location in the protected volume.•For extinguishing system units, reference to the specific types of detection and control panels (when applicable) intended to be connected to the extinguishing system unit;•For extinguishing system units, specifications and instructions for interconnection of multiple extinguishing system units; or when a means for interconnecting is unavailable, a caution statement to not use multiples of extinguishing system units;•Details on installation of each unit, mounting brackets, and all accessory equipment (as applicable);MarkingThe products should be marked with the Kiwa®-mark.Place of the mark Required specifications Method of marking•On the generator •Name of the product and supplier•Supplier’s type designation•Production date and serial number•Mass of aerosol-forming compound•Temperature range•Storage humidity range•Service life•Distances as specified in table 5•Reference to the applicationinstructions•Certification mark•Fire Class A according EN2•Fire Class B according EN2 •Non-erasable and non-detachable; •Non-flammable;•Permanent an legibleRecommendations for CustomersCheck at the time of delivery whether:•The supplier has delivered in accordance with the agreement;•The mark and the marking method are correct;•The products show no visible defects as a result of transport etc.If you should reject a product on the basis of the above, please contact:•DSPA B.V.and, if necessary,•Kiwa Nederland B.V.Consult the suppliers processing guidelines for the proper storage and transport methods.Cross referenceUL subject 2775, outline of investigation for fixed condensed aerosol extinguishing system units, November 5, 2008Chapter Description Demand 1)Result RemarksIntroduction1. Scope Implemented2. Components Implemented3 Units of measurements Implemented4 Undated references Implemented5 Glossary ImplementedConstruction6 General Implemented7 Electrically operating alarm N/A8 Control and indicators N/A9 Pneumatic control assembly pressure vessels N/A10 Pressure relief devices for pneumatic control assemblies N/A11 Gaskets and O-rings N/A12 Pressure gauges for pneumatic control assemblies N/A13 Puncturing mechanisms N/A14 Electrically operating devices N/A15 Condensed aerosol extinguishing agents A Pass See SNAP listing by USEnvironmental ProtectionAgency (EPA)16 Pneumatic control gases N/A17 Polymeric materials and nonmetallic parts N/A18 Anti-recoil devices N/A19 Pressure switches N/APerformance20 General Implemented21 Discharge test A See table 4.Discharge time of DSPA 8-1 isover 60 sec.Chapter Description Demand 1)Result Remarks22 Temperature measurement test A Pass See table 5.23 Mounting device test A Pass24 Rough Usage test A Pass25 Vibration test A Pass ImplementedDSPA 11-3, DSPA 11-6, DSPA11-7 and DSPA 8-1 were tested.DSPA 11-1, DSPA 11-2, DSPA11-4 and DSPA 11-5 aremembers of the same generatorfamily as DSPA 11-3 and DSPA11-6.DSPA 8-1 only at 0,5G26 Pyrotechnic reaction containment test Not Tested27 Fire exposure test Not Tested28 High humidity test A Pass29 Moist hydrogen sulfide air mixture corrosion test A Pass30 Moist carbon dioxide sulfur dioxide air mixture corrosionA Passtest31 Salt spray corrosion test A Pass32 Thirty day elevated temperature test A Pass33 Temperature cycling test A Pass34 One-year time leakage test N/A35 Hydrostatic pressure test N/A36 Pressure relief tests N/A37 Flexible hose assembly hose low temperature test N/A38 Calibration test gauges N/A39 Burst strength test gauges N/A40 Overpressure test gauges N/A41 Impulse test gauges N/A42 Pressure relief test gauges N/A43 Water resistance test gauges N/A44 Pneumatic operation test N/AChapter Description Demand 1)Result Remarks45 Pneumatic time delay verification test N/A46 Pressure operated alarm test N/AN/A47 Operation test of manual activators and manual pullstations48 500 cycle operation test Implemented48.1 Electrical initiators A Pass Aging test 116 days at 90 ºC =15 years and Temperature range-40°C and +75°C48.2 Other devices N/A49 Class A and B fire extinguishment tests Implemented49.1 General Implemented49.2 Class A fire extinguishment tests A Pass Not tested:Wood cribs according 49.2.2See table 1.49.3 Class B fire extinguishment tests A Pass See table 1.Implemented50 Distribution verification extinguishment tests withextinguishing system units50.1 General Implemented50.2 Test enclosure Implemented50.3 Maximum area coverage and minimum height testA Pass See table 3.arrangement procedure50.4 Maximum height test procedure A Pass See table 3.N/A51 Distribution verification extinguishment test with automaticextinguisher unit51.1 General N/A51.2 Test enclosure N/AN/A51.3 Maximum area coverage, minimum height and maximumvolume test arrangement procedure51.4 Maximum height and maximum volume test arrangementN/AprocedureN/A52 Automatic extinguisher unit automatic operationextinguishment unitChapter Description Demand 1)Result Remarks52.1 General N/A52.2 Test enclosures N/A52.3 Test arrangement procedure N/A53 Elastomeric parts test N/A54 Stress corrosion cracking test for brass parts A Pass Materials used in theconstruction are not susceptibleto ammonia stress corrosion.55 Aging test condensed aerosol generator Pass 116 days at 90 ºC = 15 years56 Aging test plastic materials N/A56.1 Air-oven aging test N/A56.2 Light and water test N/A57 Nameplate exposure test N/A58 Nameplate adhesion test N/A59 Nameplate abrasion test N/A60 Locking device and tamper indicator test N/AManufacturing and production tests61 General Implemented61.1 General Implemented61.2 Aerosol-forming compound A Pass61.3 Electrical initiators A PassN/A61.4 Hydraustatic pressure test – shells for pneumatic controlassemblies61.5 Gauge calibration test for pneumatic control assemblies N/A61.6 Leakage test for pneumatic control assemblies N/AMarkings62 General A PassInstructions63 General Implemented64 Owner’s manual A Pass See DSPA Manual V7.3 201565 Design, installation, operating and maintenance instruction A Pass See DSPA Manual V7.3 2015Chapter Description Demand 1)Result Remarks manual1) A = Applicable N/A = Not Applicable Not testedTests not performed (with requirements):•Aerosol generator explosive atmosphere test according to UL 2775 § 26•Fire Exposure test according to UL 2775 § 27•Wood cribs test according to UL 2775 § 49.2.2Page 10 of 11DSPA Non-Pressurized Condensed Aerosol Generators and Components Product specificationsTable 1Fire Class Listing AccordingUL 2775Pre burntimeSoak period Test room Density Material / fuel in seconds in seconds in m3in grams per m3A & C Polymethylmethacrylate 49.2.3 210 600 112.12 97 A & C Polypropylene 49.2.3 210 600 112.12 58A & C ABS 49.2.3 210 600 112.12 87B Heptane 49.3 30 30 112.12 34 Table 2Type Efficiency in %DSPA 11-1 100DSPA 11-2 88 - 100DSPA 11-3 90 - 100DSPA 11-4 100DSPA 11-5 94 - 100DSPA 11-6 100DSPA 11-7 100DSPA 8-1 100Table 3Type HousingType andDischargemethod Agent distribution according UL2775Minimum height /Maximum area coverage (in m)Maximum height /Maximum area coverage (in m)DSPA 11-1 Disk, radial 0.5 3.66 x 1.22 1.83 1.22 x 1.22 DSPA 11-2 Disk, radial0.5 3.66 x 2.44 2.44 1.22 x 1.22 DSPA 11-3 Disk, radial0.5 3.66 x 2.44 2.44 1.22 x 1.22 DSPA 11-4 Disk, radial 1.22 3.66 x 3.66 3.05 1.83 x 1.83 DSPA 11-5 Disk, radial 1.22 4.88 x 3.66 3.66 2.44 x 2.44 DSPA 11-6 Disk, radial 1.227.32 x 3.66 3.66 2.44 x 2.44 DSPA 11-7 Disk, axial 1.227.32 x 1.22 3.05 1.83 x 1.83 DSPA 8-1 Cylinder, axial 2.44 9.76 x 3.66 4.88 4.88 x 3.66Table 4Type Discharge timeIn SecDSPA 11-1 6 - 10DSPA 11-2 9 - 15DSPA 11-3 14 - 26DSPA 11-4 19 - 31DSPA 11-5 40 - 60DSPA 11-6 30 - 50DSPA 11-7 30 - 50DSPA 8-1 67 - 89Kiwa® product declaration K86656/02 Page 11 of 11DSPA Non-Pressurized Condensed Aerosol Generators and ComponentsTable 5Type Distance in m75°C 200°C 400°CDSPA 11-1 0.5 0.15 0.05DSPA 11-2 0.5 0.15 0.05DSPA 11-3 0.5 0.15 0.05DSPA 11-4 1.0 0.25 0.15DSPA 11-5 1.0 0.25 0.15DSPA 11-6 1.5 0.35 0.15DSPA 11-7 1.5 0.50 0.10DSPA 8-1 1.5 0.75 0.15。

declaration of conformity模板Declaration of Conformity[Your Company Name][Address][City, State, ZIP][Phone Number][Email Address][Website]Declaration of ConformityProduct Information:Product Name: [Product Name]Model Number: [Model Number]Serial Number: [Serial Number]Manufacturer: [Manufacturer]Date of Manufacture: [Date of Manufacture]I, [Your Name], as a representative of [Your Company Name], hereby declare that the above-mentioned product complies with all applicable standards and regulations as set forth by the relevant authorities. This declaration is based on the conformity assessment procedure carried out byour company in accordance with the requirements specified in [applicable standards/reference documents].1. Description of the Product:[List a detailed description of the product.]2. Applicable Standards and Regulations:[List all applicable standards and regulations that the product conforms to.]3. Technical Documentation:[Describe the technical documentation that supports the product's conformity, including test reports, design specifications, and other relevant documents.]4. Manufacturing Process:[Describe the manufacturing process, including quality control measures implemented to ensure the product's compliance with applicable standards and regulations.]5. Testing and Certification:[List any third-party testing or certification received by the product, if applicable.]6. Storage and Transportation:[Explain any specific storage or transportation requirements necessary to maintain the product's conformity.]7. Warranty and Support:[Describe the warranty terms and after-sales support provided for the product.]8. Contact Information:[Provide contact information for inquiries or further information regarding the product's conformity.]I declare that the above information is true and accurate to the best of my knowledge. Any changes or modifications made to the product without the written consent of the manufacturer may void this declaration of conformity.[Your Name][Title/Position][Date]Please note that this is a template for a Declaration of Conformity and should be tailored to fit the specific requirements of your product and industry. It is important to consult with legal experts and regulatory bodies to ensure compliance with all relevant regulations and standards.。

ce证书分类
CE证书主要分为以下三类：
1. 符合性CE证书（Certificate of
compliance/Certificate of compliance）：这是由第三方认证
机构或资质机构颁发的证书，证明产品已通过相关的CE认证测
试和评估，并符合欧洲指令和标准的要求。

必须附有测试报告等技术资料TCF，同时，企业也要签署《符合性声明书》。

2. 欧盟标准符合性CE证书（EC Attestation of conformity）：这是欧盟公告机构（Notified Body简写为NB）
颁发的证书，按照欧盟法规，只有NB才有资格颁发EC Type的CEE声明。

3. 符合性CE证书（Declaration of
conformity/Declaration of compliance）：这是由制造商或供
应商自行签发的声明，声明其产品符合CE认证的相关标准和要求。

可以用欧盟格式的企业《符合性声明书》代替。

这些证书都与CE认证相关，CE认证旨在确保产品符合欧洲经济区内的相关法律法规和标准，以保障产品的安全性和符合性。

CE证书的种类主要有以下三种：
1.Certificate of compliance/Certificate of compliance《符合性CE证书》，此为第三方机构（中介或测试认证机构）颁发的符合性声明，
必须附有测试报告等技术资料TCF，同时，企业也要签署《符合性声明书》。

2.EC Attestation of conformity《欧盟标准符合性CE证书》，此为欧盟公告机构（Notified Body简写为NB）颁发的证书，按照欧盟法规，
只有NB才有资格颁发EC Type的CEE声明。

3.Declaration of conformity/Declaration of compliance《符合性CE证书》，此CE证书属于自我声明书，不应由第三方机构（中介或测试
认证机构）签发，因此，可以用欧盟格式的企业《符合性声明书》代替。

以上信息仅供参考，如有需要，建议您咨询专业技术人员。

declaration of conformity模板Declaration of Conformity[Your Company Logo]Declaration of ConformityProduct Information:Product Name: [Product Name]Model Number: [Model Number]Serial Number: [Serial Number]Date of Manufacture: [Date of Manufacture]We, [Your Company Name], hereby declare that the aforementioned product is in conformity with the essential requirements and provisions set out in the relevant directives and standards.1. Identification of the Manufacturer:Manufacturer's Name: [Your Company Name]Manufacturer's Address: [Your Company Address]Contact Information: [Your Company Contact Information]2. Authorized Representative:Name: [Authorized Representative Name]Address: [Authorized Representative Address]Contact Information: [Authorized Representative Contact Information]3. Product Description:Description: [Product Description]Technical Specifications: [Technical Specifications]4. Standards and Directives:The product conforms to the following standards and directives:- [List of relevant standards and directives]5. Conformity Assessment:The conformity assessment procedure was carried out in accordance with the requirements of the applicable directives and standards. [Provide relevant details of the assessment procedure, such as testing, certification, or self-declaration.]6. Technical Documentation:All relevant technical documentation as required by the applicable directives is available and can be provided upon request.7. Declaration:We hereby declare that the above-mentioned product meets all applicable directives and standards and is in conformity with all essential requirements. It is safe for its intended use and does not pose any risk to health, safety, or the environment.Date: [Date]Signature: [Your Signature] [Your Name][Your Position][Your Company Name]。