880M 850M 等系统使用
机床螺距补偿参数：5016bit 1 and bit 2决定补偿功能
220* backlash
正向补偿指针点负向补偿指针点补偿点间隔补偿值
X轴3160=20 3200=20 3240=20000 3280=
Y轴3161=120 3201=120 3241=20000 3281=
Z轴3162=220 3202=220 3242=20000 3282=
12.6.5 Machine data for fictitious axes
MD 224* Software limit switch
MD 228* Software limit switch
MD 232* Software limit switch
MD 236* Software limit switch
The software limit switch need not be input if the fictitious working area is outside the real possible working area, as the control always restricts the fictitious software limit switch to the limit switch of the A1R axis (linear axis of transformation).
MD 276* Acceleration
The acceleration value must be calculated in such a way that the real axes of transformation are not overloaded (minimum acceleration value of A1R to A5R).
MD 280* Maximum speed
MD 288* JOG speed
MD 292* Rapid JOG
The speeds can be freely selected, as they are monitored by the control.
MD 304* IPO parameter
MD 360* Operating mode group of the axis
MD 564* Bit 6 Fictitious axes
The axis is declared as a ”fictitious axis”. Fictitious axes have no position control. The MD 200* measuring circuit assignment is therefore meaningless.
MD 564* Bit 7 Axis exists
MD 568* Encoding of the axis name
MD 576* Axis not permitted in channel
12.1.1 Corresponding data
? NC-MD 316* (Reference point pointer for + compensation)
? NC-MD 320* (Reference point pointer for - compensation)
? NC-MD 324* (Distance between 2 leadscrew error compensation points)
? NC-MD 328* (Compensation value)
? NC-MD 344* (Modulo value for rotary axis)
? NC-MD 6000 to 6249 (Leadscrew error compensation points)
Note carefully:
Changes to NC MD data for leadscrew error compensation do not go into effect until after
completion of POWER ON and reference point approach.
MPF 100（坐标测量程序，西门子系统使用）
R11=1 （测量轴号X=1，Y=2，Z=3）
R2=-6 反向量（起点反向量）
R3=-80 测量间距（间隔）
R4=5 暂停时间(间隔点)
R6=-560 （终点坐标量程）
R20=10 （测量次数）
R21=0 记次开始
N5 @714
R1=160 测量起点坐标值
R5=160 起点坐标
R1=R1-R2 （计算起点位置）绝对坐标
N10G0G53@440R11R1 （R11为定义轴，@440为R11轴移动到R1位置）G04 F=R4
N15R1=R5-R3
N20 R1=R1+R3
N25 G0G53@440R11R1
N30 G4F=R4
N35 @124R6R1K-20 （如果R6≥R1则向下执行，否则执行N20句）
N40 R1=R6
N45 R1=R1+R2
N50 G0G53@440R11R1
G04 F=R4
N55 R1=R1-R2
N60 G0G53@440R11R1
N65 G4F=R4
N70 R1=R1-R3
N75 @124R5R1K85（如果R5≥R1则向下执行，否则执行N85句）
N80 @100K-60 （绝对跳转至N60）
N85 @620R21 （R21的数字递增，至10停）
N90 @125R20R21K-5
N95 M30
Y轴补偿点表
Z轴补偿点表