常用机械密封专有英文词汇
inner circulation--内循环
outer circulation--外循环
self circulation--自循环
flush--冲洗
flush fluid--冲洗流体
quench--阻封
quench fluid--阻封流体
buffer fluid--隔离流体
temperature adjustable fluid--调温流体
coolant--冷却流体
heating fluid--加热流体
sealed medium--被密封介质
sealant--密封流体
pv --pv值(密封流体压力P与密封端面平均滑动速度V的乘积) limiting pv --密封达到失效时的PV值.它表示密封的水平
working pv --极限PV值除以安全系数
PcV--端面比压Pc与密封端面平均滑动速度V的乘积
limiting PcV --密封达到失效时的PcV值.它表示密封材料的工作能力working PcV --许用PcV值.极限PcV值除以安全系数
leakage rate-- 泄漏量
run out--跳动
wear rate--磨损率
operating life--工作寿命
operating period--使用期
abortive failure--早期失效
Operating limits:工作参数
Speed/velocity:转速
Combination of material:材料组合
Halted ring:弹簧挡圈
Bellows:波纹管
Retainer:传动套，传动座
Drive ring:压圈
Cup gasket:静环套
Spring retainer:弹簧座
O-ring: O形圈
Tension spring:拉簧
Stationary seat:静环形式/静环基座
Rotary seat:动环座
Drive screw:传动螺钉
Wave spring/Bellow spring:波形弹簧
Rotary o-ring:动环O形圈
Stationary o-ring:静环O形圈
Collar:定位套
Snap ring/clamp ring:卡环
Disc/thrust ring:止推环
Wedge ring:楔形环
Mating ring:静止环/静环
Primary ring:动止环/动环
Inventory:存货
Agitator:搅拌器
Cryogenics:低温学
Mixer:搅拌机
Refinery:炼油
Petrochemical:石化
Pulp:纸浆
Paramecia:配药
Desalination:脱盐
Wastewater:污水
Impeller:叶轮
Fit:安装
Lead:石墨，铅
Edge:边缘
Grade:等级
Secondary sealing element:辅助密封材质Hydrostatic:流体静力学的
Cross-section:横截面
Material code:材料代码
Seal size:密封轴径尺寸
Assembly number:装配代码
Sulphuric:硫酸
Nitric acid:销酸
Phosphoric acid:磷酸
Hydrochloric:盐酸
PV—pressure/velocity:压力与转速
RS—rotating seat:动环座
Multiplier:增效器
TC—tungsten carbide:硬质合金
Pin:销
Engage:接合,啮合
Pro剖面/侧面
Adapter:适配器
1.secondary sealing element 辅助密封, 一般指是橡胶材料
2.primary ring 动环
3.hardware 结构件
4.mating ring 静环
5.mechanical loading device 一般是指弹簧的材料
1.Type 密封类型
2.direction of the spring 弹簧旋向(RH-右旋,LH-左旋)
3.type of seat 静环形式(例如G9,G6,G60...)
https://www.doczj.com/doc/977346435.html,bination of material 材料组合
a.rotary ring (primary ring ) 动环
b.stationary ring (mating ring ) 静环
c.secondary mech.seals 辅助密封一般指橡胶
d.spring 弹簧
e.other metal parts 其他金属部件
常有的橡胶材料
1.丁晴橡胶NBR--Nitrile butadiene rubber
2.乙丙橡胶EPR/EPDM--ethylene propylene rubber
3.氟橡胶FPM/FKM--fluoroelastomer
4.硅橡胶MVQ--silicon rubber
5.氯丁橡胶CR--neoprene/chloroprene rubber
6.氢化丁晴HNBR--hydrogen NBR
7.全氟橡胶Kalrez / FFKM --perfluorocarbon rubber
四氟类材料
1.纯聚四氟乙烯PTFE--polytetrafluoroethylene (Teflon和TEF也可以表达)
2.四氟填充玻璃纤维glassfibre filled PTFE
3.四氟填充碳纤维carbonfibre filled PTFE
4.四氟包覆氟橡胶FPM coated PTFE
5.四氟包覆乙丙橡胶EPDM coated PTFE
6.四氟包覆硅橡胶MVQ coated PTFE
7.柔性石墨fexible graphite, 像比较有名的是GRAFOIL?? fexible graphite
国外客户常要的碳化硅(silicon carbide)材料
1.无压烧结碳化硅sintered pressureless bonded sic (S-SIC)
2.无压烧结碳化硅镶装shrink-fitted /inserted S-SIC
3.反应烧结碳化硅sintered reaction bonded sic (R-SIC)
4.反应烧结碳化硅镶装shrink-fitted /inserted R-SIC
5.表面硅化石墨surface silicated sic
常用氧化铝材料:
1.含99%白色氧化铝.99% AL2O3
2.含95%白色氧化铝.95% AL2O3
3.金属陶瓷cermet
石墨材料:
1.浸锑石墨antimony filled carbon
2.浸巴氏合金石墨carbon-graphite impregnated babbit
3.浸呋喃树脂石墨carbon-graphite impregnated Furan resin
4.浸环氧树脂石墨carbon-graphite impregnated Epoxy resin
5.浸酚醛树脂石墨carbon-graphite Phenol Aldehyde resin
6.热压石墨,hot pressing carbon graphite
金属材料
stainless steel (S.S)--不锈钢--(国外客户经常需要的牌号是304,316,316L)
Ni-resist iron = cast iron--高镍铸铁，现在客人对这个材料需要的比较多
Hast. alloy--合氏合金
AM350--沉淀硬化不锈钢
brass--黄铜
CDMCu--双相钢（用在铸件上比较多）
机械密封分类术语...
1.机械端面密封-mechanical face seal
2.流体动压式机械密封-hydrodynamic mechanical seal
3.切向作用流体动压式机械密封-tangential acting hydrodynamic mechanical seal
4.径向作用流体动压式机械密封-radial acting hydrodynamic mechanical seal
5.流体静压式机械密封-hydrostatic mechanical seal
6.外加压流体静压式机械密封-outside pressurized hydrostatic mechanical seal
7.自加压流体静压式机械密封-self pressurized hydrostatic mechanical seal
8.非接触式密封-non contacting (free contacting) mechanical seal
9.内装式机械密封-internally mounted mechanical seal
10.外装式机械密封-externally mounted mechanical seal
11.弹簧内置式机械密封-mechanical seal with inside mounted spring
12.弹簧外置式机械密封-mechanical seal with outside mounted spring
13.背面高压式机械密封-mecanical seal with high back pressure
14.背面低压式机械密封-mechanical seal with low back pressure
15.内流式机械密封-mechanical seal with inward leakage
16.外流式机械密封-mechanical seal with outward leakage
17.弹簧旋转式机械密封-spring rotating mechanical seal
18.弹簧静止式机械密封-spring standing mechanical seal
19.单弹簧式机械密封-single-spring mechanical seal
20.多弹簧式机械密封-multiple-spring mechanical seal
21.非平衡式机械密封-unbalanced mechanical seal
22.平衡式机械密封-balanced mechanical seal
23.单端面机械密封-single mechanical seal
24.双端面机械密封-double mechanical seal
25.轴向双端机械密封-axial double mechanical seal
26.径向双端面机械密封-radial double mechanical seal
27.串联机械密封-tandem mechanical seal
28.橡胶波纹管机械密封-rubber-bellows mechanical seal
29.聚四氟乙烯波纹管机械密封-PTFE-bellows mechanical seal
30.金属波纹管机械密封-metal bellows mechanical seal
31.焊接金属波纹管机械密封-welded metal bellows mechanical seal
32.压力成型金属波纹管机械密封-formed metal bellows mechanical seal
33.带浮动间隔环的机械密封-mechanical seal with floating intermediate ring
34.磁力机械密封-magnetic mechanical seal
机械密封零件术语的常用词汇....
1.sealing ring --密封环
2.seal face--密封端面
3.seal interface--密封界面
4.rotating ring--动环/旋转环
5.stationary ring--静环/静止环
https://www.doczj.com/doc/977346435.html,pensated ring--补偿环
7. un-compensated ring--非补偿环
8. seal head--补偿环组件
9.primary seal--主密封
10.secondary seal--副密封
11.auxiliary seal--辅助密封
12.auxiliary seal ring--辅助密封圈
13.bellows--波纹管
14.pushing out ring--撑环
15.back-up ring--挡圈
https://www.doczj.com/doc/977346435.html,pensated ring adaptor--补偿环座
17.un-compensated ring adaptor--非补偿环座
18.spring adaptor--弹簧座
19.seal adaptor--波纹管座
20.retainer--传动座
21.driving screw--传动螺钉
22.set screw--紧定螺钉
23.snap ring--卡环
24.clamp ring--夹紧环
25.anti-rotating pin--防转销
26.annular seal space--密封腔
27.seal chamber--密封腔体
28.end cover--密封端盖
29.elastic component--弹性元件
30.a pair of friction components--摩擦副
机械密封常用英语表达词汇
inner circulation--内循环
outer circulation--外循环
self circulation--自循环
flush--冲洗
flush fluid--冲洗流体
quench--阻封
quench fluid--阻封流体
buffer fluid--隔离流体
temperature adjustable fluid--调温流体
coolant--冷却流体
heating fluid--加热流体
sealed medium--被密封介质
sealant--密封流体
pv value--pv值(密封流体压力P与密封端面平均滑动速度V的乘积) limiting pv value--密封达到失效时的PV值.它表示密封的水平working pv value--极限PV值除以安全系数
PcV--端面比压Pc与密封端面平均滑动速度V的乘积
limiting PcV value--密封达到失效时的PcV值.它表示密封材料的工作能力working PcV value--许用PcV值.极限PcV值除以安全系数
leakage rate-- 泄漏量
run out--跳动
wear rate--磨损率
operating life--工作寿命
operating period--使用期
abortive failure--早期失效
Operating limits:工作参数
Speed/velocity:转速
Combination of material:材料组合
Halted ring:弹簧挡圈
Bellows:波纹管
Retainer:传动套，传动座
Drive ring:压圈
Cup gasket:静环套
Spring retainer:弹簧座
O-ring: O形圈
Tension spring:拉簧
Stationary seat:静环形式/静环基座
Rotary seat:动环座
Drive screw:传动螺钉
Wave spring/Bellow spring:波形弹簧
Rotary o-ring:动环O形圈
Stationary o-ring:静环O形圈
Collar:定位套
Snap ring/clamp ring:卡环
Disc/thrust ring:止推环
Wedge ring:楔形环
Mating ring:静止环/静环
Primary ring:动止环/动环
Inventory:存货
Agitator:搅拌器
Cryogenics:低温学
Mixer:搅拌机
Refinery:炼油
Petrochemical:石化
Pulp:纸浆
Paramecia:配药
Desalination:脱盐
Wastewater:污水
Impeller:叶轮
Fit:安装
Lead:石墨，铅
Edge:边缘
Grade:等级
Secondary sealing element:辅助密封材质Hydrostatic:流体静力学的
Cross-section:横截面
Material code:材料代码
Seal size:密封轴径尺寸
Assembly number:装配代码Sulphuric:硫酸
Nitric acid:销酸
Phosphoric acid:磷酸
Hydrochloric:盐酸
PV—pressure/velocity:压力与转速RS—rotating seat:动环座
Multiplier:增效器
TC—tungsten carbide:硬质合金
Pin:销
Engage:接合,啮合
Profile:剖面/侧面
Adapter:适配器
Titled:倾斜的
Weld/welt:焊接
Nested:嵌套的,镶装的
Configuration:配置,构造
Axial:轴向的,轴的
Working height/length:工作高度Tolerance:公差,容差
Operating pressure:工作压力
FIM—full indicator movement: Lubricity:光滑
Gravity:重力
Face material:密封面材料
Insert/shrink-fitted:镶装的
Primary ring adapter:动环座
Mating ring adapter:静环座
Delivery period:交货期
Set screw:固定螺钉
Cap screw:帽螺钉
Gland:填料函盖
Drive retainer:传动套
Plate:镀金
Gland plate:密封座
Mean time:平均时
Durability:耐用性
Thrust ring:推环
Clamp ring:卡环
Eccentricity:偏心率/度,偏心距Deflection:偏斜,偏差
Runout:偏转,溢流
Pilot pins: 定位销
Bolt:螺栓
Screw:螺钉
Nut:螺母
Washer:垫圈
Pin:销
Rivet:铆钉
Anchor:壁虎
Machine screw:机械螺钉
Wooden screw:木螺钉
Threaded rod螺杆
Wire rope clamps:玛卡
Hex head pipe plugs:六角形螺塞Phillip:十字槽
Spring-loaded pluger: 弹簧销
Hex head:六角形头
Flange:法兰
Seal component materials:密封材料成分
Secondary sealing element:辅助密封材料
Primary ring:动环
Mating ring:静环
Hardware:结构件
Mechanical loading device (spring):弹簧材料
Ovality:椭圆
Letter of intent:意向书
Rotary ring is whole part or shrink-fitted:动环是整体还是镶装的Leaf:金属薄片
End play:轴向间隙
Pad:衬垫
Asymmetric:不对称的
Seal adapter:密封座
T andem:前后的，串联的
Inlet:进口
Outlet:出口
Inboard:内侧/介质端
Outboard:外侧/大气端
Convection:传送，对流
Port:端口，
Slot:狭槽
Reducing agent:还原剂
Notch:槽口，凹口
Band:镶边
Clogging:堵塞
Tune 弹簧)圈数
Foul:淤塞
Flatness:平面度
Downtime:检修时间
Alternative methods:替代方法
Wear ring:磨损环
Torsion:扭距
Cast:铸件
Confining:狭窄的
Spring seat:弹簧座
Plug-proof:防转销
Drive ring:推环
Push ring: 推环
Halted ring: 挡圈
Cup gasket: 静环套
Rotary ring holder/adapter/carrier: 动环座
Axial pipe:轴套
Drive ring/plunger collar:压圈
Spring retainer/seat: 弹簧座
Impeller:叶轮
Outside cup gasket: 静环外套
Inside cup gasket: 动环内套
Spring holder:弹簧垫
Seal ring:密封环
Framework:骨架
Square ring:方型圈
Wave spring:波形弹簧
Cylinder spring:圆柱弹簧
Coil spring:锥形弹簧
Integral seal case:整体密封盒
Purity:纯度
Density:密度
HS—hardness:硬度
Tensile strength:抗拉强度
Bending strength:抗弯强度
Compression strength:抗压强度
Thermal conductivity:传热导系数
Coefficient of thermal expansion:热膨胀系数
Heat resistance:耐热
Thermal impact coefficient:热冲击系数
Acid resistance:耐酸
Medium:介质
Porosity:显气孔率
Rockwell hardness:洛式硬度
Breaking strength:抗析强度
Stability of thermal vibration: 抗震稳定性
Optical flatness:工作面平整度
Roughness:粗糙度
Lightbrand:光带
Classification:分类
Model:型号
Thore hardness: 肖氏硬度
Feature:特性
Stamping:冲压
Lobe pump:凸轮泵
Step:台阶
1、防转销Anti-Rotating Pin 16、螺栓Bolt
2、静环密封圈Stationary Seal Ring 17、螺钉Screw
3、下静环Lower Stationary Ring 18、轴套螺母Bushing nut
4、动环密封圈Rotating Seal Ring 19、0形密封圈0-ring
5、下动环Lower Rotating Ring 20、紧定套Set Bushing
6、小弹簧Small Spring 21、紧定螺母Set Nut
7、螺钉Screw 22、调节套Adjust Bushing
8、弹簧座Spring Adater 23、毡封油圈Oil seal
9、推环Thrust Ring 24、滚动轴承Bearing
10、轴套Shaft Sleeve 25、垫板Gasket Plate
11、螺栓Bolt 26、J形油封Seal Ring
12、密封箱体Seal Box 27、推环Thust Ring
13、密封垫Gasket 28、上静环Upper Stationary Ring
14、密封箱盖Seal Box Cover 29、上动环Upper Rotating Ring
15、轴承盖Bearing Cover
accredited 官方认可的；鉴定合格的 advantage 优势； agency 代理处；行销处；经售店 agenda 议事日程；事项 analog 模拟 APEC ( = Asia Pacific Economic Cooperation Forum) Appetize r 开胃食品 Appliances 家用）电器 常用词汇表 (the) Americas 北美洲、中美洲和南美洲的总称 a la carte 照菜单点 菜 abstrac t 摘要， 概 要 academic conference 学术研讨 会 accessory 附属 附 件 accident report 事故报 告 Apparel 衣服；服 装 acknowledge 承认；感谢 ad hoc committee 临时成立的工作委员会 advance funds 预支货款 amplifier 扩音器 animation 动画 亚太经合组织
Application service provider (ASP) 应用软件服务商 Arc light 弧光 Arrival pattern 团队抵达时间 Arrogan t 自大的，傲慢的 Artic le 物品：商品 Artist ic 艺术的；美术的 Assemble 集合，聚集；装 配 Assimilat e 同化；消化；吸收；彻底了解 Assistant stage manager 助理展台经 理 Associated firm 联号 Associatio n 协会 Attendance 观众；出席者，出席人 数 Attendee 参加会议或展览的人；出席 者 Attracti on 景点；引人注意之物 Au lait 加牛奶 Auction 拍卖 Audio conference 电话会议 Audiovisual (AV) 视听设备 Audiovisual aids 视听辅助设备 Authorized signature 授权签字 Automaker 汽车制造 商 Automation 自动化，自动 机
机械工业专业英语词汇 金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist 弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 几何形状 geometrical 精度 precision 正弦形的 sinusoid 交流电路 AC circuit 机械加工余量 machining allowance 变形力 deforming force 变形 deformation 应力 stress 硬度 rigidity 热处理 heat treatment
退火 anneal 正火 normalizing 脱碳 decarburization 渗碳 carburization 电路 circuit 半导体元件 semiconductor element 反馈 feedback 发生器 generator 直流电源 DC electrical source 门电路 gate circuit 逻辑代数 logic algebra 外圆磨削 external grinding 内圆磨削 internal grinding 面磨削 plane grinding 变速箱 gearbox 离合器 clutch 绞孔 fraising 绞刀 reamer 螺纹加工 thread processing 螺钉 screw 铣削 mill 铣刀 milling cutter 功率 power 工件 workpiece 齿轮加工 gear mechining 齿轮 gear 主运动 main movement 主运动方向 direction of main movement 进给方向 direction of feed 进给运动 feed movement 合成进给运动 resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向 direction of resultant movement of cutting 切削深度 cutting depth 前刀面 rake face 刀尖 nose of tool 前角 rake angle
【essay】常用academic词汇来源：谭希的日志 1.增补(Addition) in addition另外, furthermore此外, again, also, besides, moreover此外, similarly, fi nally最后 2.比较(Comparison) in the same way, likewise同样地, similarly, equally, in comparison比较起来, just as 同样地 3.对照(Contrast) whereas然而, in contrast与此相反, on the other hand, instead同样, however然而, nevertheless然而, unlike, even though即使, on the contrary, while 4.因果(Cause and effect) because, because of, for, since, due to, owing to, thanks to, as a result(of), accor dingly, hence, so, thus 5.强调(Emphasis) certainly, above all, indeed, of course, surely, actually, as a matter of fact, chiefly, especially, primarily, in particular, undoubtedly, absolutely, most imprtant 6.让步(Concession) although, though, after all, in spite of, nevertheless, still, provided, while it is tru e.... 7.例证(Exemplification) for example, for instance, that is, namely, such as, in other words, in this case, b y way of illustration. 8.总结(Conclusion) to sum up, to conclude, in a word, in short, in brief, all in all, in all, to put it in a nutshell, in summary 9.推断(Inference) therefore, as a result(of), consequently, accordingly, so, otherwise 10.时间和空间(Time and space) afterward, after, first, later, then, soon, outside, near, beyound, above, below, on the right(left), in the middle, opposite, in front of
常见手机零配件及电子产品中英文对照
零件中英文对照Replacement Parts / Repair Parts 备用零件 LCD Screen 液晶 Touch Screen / Digitizer 触摸屏 LCD Assembly 液晶总成 Battery 电池 Flex Cable 排线 Keypad / Keypad Flex Cable 按键排线 Audio Earphone Flex Cable 音频排线 Charging Port Dock Connector Flex Cable 尾插排线Proximity Light Sensor Flex Cable 感应排线 Home button 返回键 Power Button 开关键 Mute/Silent Button 静音键 Housing / Back Cover 后盖 Metallic / Metal Brushed Housing 金属拉丝后盖Middle Plate 中板 Middle Bezel / Frame 中框 Motor / Vibration Motor 马达 Full Housing / Faceplates 全套壳 Front Facing Camera 前置摄像头 Back Camera 后置摄像头 Speaker / Loud Speaker 喇叭 Earpiece speaker 听筒 Microphone 麦克风 Ringer Buzzer 振铃器 SIM Card Tray 卡托 Headphone Jack Hole 耳机孔 Glass Screen Lens 镜面 SIM Card Holder / Connector SIM卡座 Memory Card Holder 内存卡卡座 Battery FPC Plug 电池座 Screw 螺丝 Anti-dust Mesh 防尘网 Adhesive Strip Sticker 贴纸 Ejection Pin 取卡针 Mainboard / Motherboard 主板
组装、冲压、喷漆等专业词汇 Assembly line组装线 Layout布置图 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 repair修理 operator作业员 QC quality品管 supervisor 课长 section supervisor课长 deputy section supervisor =vice section superisor副课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 front plate前板 rear plate后板 chassis基座 bezel panel面板 power button电源按键 reset button重置键Hi-pot test of SPS高源高压测试 V oltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 punching machine 冲床 robot机械手 lathe车床 planer |'plein|刨床 miller铣床 grinder磨床 driller??床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 group leader/supervisor组长 line supervisor线长 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 iudustrial alcohol工业酒精 Tiana天那水 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏 大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head 螺丝滑头 speckle斑点 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 to return material/stock to退料 scraped |'skræpid|报废 (be)qualfied, up to grade合格 not up to grade, not qualified不合格
Academic Vocabulary Equipping yourself with the relevant academic vocabulary will give you a head start in your university studies. Especially if you’re a second language learner of English, studying in a foreign language can be very difficult and time-consuming. In order to do well, you may want to consider the following ways of learning academic vocabulary more effectively and relevantly. You will need: The General Service List. The GSL is a list of general and basic vocabulary of English used in order of frequency. It has been recognized and used quite extensively among second lan- guage learners of English for work and study. It was first created by West in 1953. The version used was then adapted by Baumann and Culligan in 1995. It contains almost 2,300 words. The GSL here is divided into smaller sublists. Sublist 1 has the first 500 words. Sublist 2 the next 500 words etc. For the complete word lists, refer to: https://www.doczj.com/doc/977346435.html,/~alzsh3/acvocab/wordlists.htm Subject-related Word List. This is a list of words which is specific to your discipline of studies, for example, finance, accounting, education and others. The index at the back of your textbook is generally the best guide to the terms, concepts that are widely used in the subject. The index is a valuable guide to understanding the key concepts and terms used in a subject. So make good use of the book index. You may also want to consult this site for some additional help and ideas. https://www.doczj.com/doc/977346435.html,/vocab/select/selframs.htm The Academic World List. The AWL is first developed by and compiled by Averil Coxhead Victoria University of Wellingtown, New Zealand. The AWL contains 10 sublists that include 570 word families which appeared most frequently in academic texts. There are 60 words in each sublist 1-9, and 30 in Sublist 10. Sublist one consists of the 60 mostly frequently ap- peared words in the academic texts and sublist two consists of the next 60 word families and so on. The academic corpus contained approximately3,500,000 active vocabulary taken from a variety of texts used and read across the faculties, spanning over more than 25 subject areas. The complete Academic Word list of 570 root words and their word families can be conveniently found in https://www.doczj.com/doc/977346435.html,/vocab/select/awl.htm with a quick link to their the dictionary meanings. A note to mention is that the list here is arranged in alphabetical order and NOT by sublists. Nevertheless, this is a great site to learn the meanings of the AWL words.
机械业内常用的中英文术语对照 1 管道组成件 Piping component 1.1 管子 Pipe 管子(按照配管标准规格制造的) pipe 管子(不按配管标准规格制造的其他用管) tube 钢管 steel pipe 铸铁管 cast iron pipe 衬里管 lined pipe 复合管 clad pipe 碳钢管 carbon steel pipe 合金钢管 alloy steel pipe 不锈钢 stainless steel pipe 奥氏体不锈钢管 austenitic stainless steel pipe 铁合金钢管 ferritic alloy steel pipe 轧制钢管 wrought-steel pipe 锻铁管 wrought-iron pipe 无缝钢管 seamless (SMLS) steel pipe 焊接钢管 welded steel pipe 电阻焊钢管 electric-resistance welded steel pipe 电熔（弧）焊钢板卷管 electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管 spiral welded steel pipe 镀锌钢管 galvanized steel pipe 热轧无缝钢管 hot-rolling seamless pipe 冷拔无缝钢管 cold-drawing seamless pipe 水煤气钢管 water-gas steel pipe 塑料管 plastic pipe 玻璃管 glass tube 橡胶管 rubber tube 直管 run pipe; straight pipe 1.2 管件 Fitting 弯头 elbow 异径弯头 reducing elbow 带支座弯头 base elbow k半径弯头 long radius elbow 短半径弯头 short radius elbow 长半径180巴渫?long radius return 短半径180巴渫?short radius return
闻报道常用英语词汇 accredited journalist n. 特派记者advertisement n．广告．advance n．预发消息；预写消息affair n．桃色新闻；绯闻anecdote n．趣闻轶事assignment n．采写任务attribution n. 消息出处，消息来源back alley news n. 小道消息backgrounding n．新闻背景Bad news travels quickly. 坏事传千里。banner n．通栏标题beat n．采写范围blank vt. "开天窗" body n. 新闻正文boil vt．压缩(篇幅) box n. 花边新闻brief n. 简讯bulletin n．新闻简报byline n. 署名文章caption n．图片说明caricature n．漫画carry vt．刊登cartoon n．漫画censor vt. 审查(新闻稿件)，新闻审查chart n．每周流行音乐排行版clipping n．剪报column n．专栏；栏目columnist n．专栏作家continued story 连载故事;连载小说contributing editor 特约编辑contribution n．(投给报刊的)稿件;投稿contributor n．投稿人copy desk n．新闻编辑部copy editor n．文字编辑correction n．更正(启事) correspondence column读者来信专栏correspondent n.驻外记者；常驻外埠记者cover vt．采访;采写cover girl n. 封面女郎covert coverage 隐性采访;秘密采访crop vt．剪辑(图片) crusade n．宣传攻势cut n．插图vt．删减(字数) cut line n．插图说明daily n．日报dateline n．新闻电头deadline n．截稿时间dig vt．深入采访；追踪(新闻线索)；“挖”(新闻) digest n．文摘editorial n．社论editorial office 编辑部daily 日报morning edition 晨报evening edition 晚报quality paper 高级报纸popular paper 大众报纸evening paper 晚报government organ 官报party organ 党报trade paper 商界报纸Chinese paper 中文报纸English newspaper 英文报纸vernacular paper 本国文报纸Japanese paper 日文报纸political news 政治报纸Newspaper Week 新闻周刊the front
机械英语 机加工专业(单词/词组)中英对照 A abrasion n. 磨料,研磨材料,磨蚀剂, adj. 磨损的,磨蚀的 abrasive belt n. 砂带 abrasive belt grinding n. 砂带磨削,用研磨带磨光 abrasive cut-off machine n. 砂轮切断机 abrasive dressing wheel n. 砂轮修整轮 abrasive grain n. 磨料粒度 abrasive grit n. 研磨用磨料,铁粒 abrasive lapping wheel n. 磨料研磨轮 accuracy of position n. 位置精度 accuracy to shape n. 形状精度 active cutting edge n. 主切削刃 adapter flange n. 连接器法兰盘 adjointing flanks n. 共轭齿廓 align n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准 angle milling cutter n. 角铣刀 angular grinding n. 斜面磨削,斜磨法 angular milling n. 斜面铣削 angular plunge grinding n. 斜向切入磨削 angular turning n. 斜面车削 arbour n. 刀杆,心轴,柄轴,轴,辊轴 attachment n. 附件,附件机构,联结,固接,联结法 automatic bar machine n. 棒料自动车床 automatic boring machine n. 自动镗床 automatic copying lathe n. 自动仿形车床 automatic double-head milling machine n. 自动双轴铣床 automatic lathe n. 自动车床 automatic turret lathe n. 自动转塔车床 B belt grinding machine n. 砂带磨床 bench lathe n. 台式车床 bevel n. 斜角，斜面，倾斜，斜切，斜角规，万能角尺，圆锥的，倾斜的，斜边，伞齿轮，锥齿轮 bevel gear cutting machine n. 锥齿轮切削机床 bevel gear tooth system n. 锥齿轮系，锥齿轮传动系统 borehole n. 镗孔，镗出的孔，钻眼 boring n. 镗孔，钻孔，穿孔 boring fixture n. 镗孔夹具 boring machine n. 镗床 boring tool n. 镗刀 boring, drilling and milling machine n. 镗铣床
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群（FOXTEQ）CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value（核心价值） Love 愛心
金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematics 静力学static 分析力学analysis mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarbonization 渗碳carboniz ation 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding
The Academic Word List (AWL) by Sublist Sublist 1 of the Academic Word List - Most frequent words in families This sublist contains the most frequent words of the Academic Word List in the Academic Corpus. The most frequent members of the word families in Sublist 1 are listed below. analysis approach area assessment assume authority available benefit concept consistent constitutional context contract create data definition derived distribution economic environment established estimate evidence export factors financial formula function identified income indicate individual interpretation involved issues labour legal legislation major method occur percent period policy principle procedure process required research response role section sector significant similar source specific structure theory variables
机械专业英语词汇 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck
电子公司常用英语术语一:常用术语 CMM Component module move 机动组件整合 CEM Contract Manufaction service 合约委托代工 IBSC Internet Business Solution Center 国际互联网应用中心 PCEG Personal Computer Enclosure group 个人计算机外设事业群（FOXTEQ）CCBG Connector&cable business group CPBG Competition business group ESBG Enterprise system business group 鸿富锦事业群 SABG system assembly business group 系统组装事业群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鸿准 Stamping tool shop I 冲模一厂 Stamping tool shop II 冲模二厂 Prototype workshop 样品中心 Steel factory 裁剪厂 PCE molding tooling workshop PCE塑模厂 Hua Nan test and measurement center 华南检测中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 镁合金 Engineer standard 工标 Document center (database center)数据中心
Sublist 1 of the Academic Word List analyse analysed analyser analysers analyses analysing analysis analyst analysts analytic analytical analytically analyze analyzed analyzes analyzing approach approachable approached approaches approaching unapproachable area areas assess assessable assessed assesses assessing assessment assessments reassess reassessed reassessing reassessment unassessed assume assumed assumes assuming assumption assumptions authority authoritative authorities available availability unavailable benefit beneficial beneficiary beneficiaries benefited benefiting benefits concept conception concepts conceptual conceptualisation conceptualise conceptualised conceptualises conceptualising conceptually consist consisted consistency consistent consistently consisting consists inconsistencies inconsistency inconsistent constitute constituencies constituency constituent constituents constituted constitutes constituting constitution constitutions constitutional constitutionally constitutive unconstitutional context contexts contextual contextualise contextualised contextualising uncontextualised contextualize contextualized contextualizing uncontextualized contract contracted contracting contractor contractors contracts create created creates creating creation creations creative creatively creativity creator creators recreate recreated recreates recreating data define definable defined defines defining definition definitions redefine redefined redefines redefining undefined derive derivation