THE NAME OF ASSY PARTS 部件中英文名对照
1.top-plt顶板
2.stripper-plt：水口板
3.a-plt：Ａ板
4.b-plt：Ｂ板
5.eje-top-plt顶针面板
6.eje-bottom-plt顶针底板
7.bottom-plt底板
8.spacer-plt方铁
9.cav前模
10.cav-sub前模镶件
11.core后模
12.core-sub后模镶件
13.locating定位圈
14.sprue唧嘴
15.sprue-pin防转梢
16.lif-acc斜顶杂件
17.lifter斜顶
18.lif-leg斜顶腿
19.lif-guide斜顶压块20.fix-acc前模杂件
21.mov-acc后模杂件
22.eje-pins顶针全图
23.fix-mb前模模胚
24.mov-mb后模模胚
25.assy 总装图
26.pro-1.00x 产品缩水图
27.pull-block拉杆
28.sleeve司筒
29.stopper限位柱
30.support撑头
31.sld-acc行位杂件
32.sld-sub行位镶件
33.sld-body行位体
34.sld-guide行位压块
35.sld-cam行位铲咀
36.sld-wear行位油板
37.angle-pin斜导柱
38.pull-pin 钩针
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
常用模具零件中英文对照表 2005-12-19 14:51:17中国注塑网 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin
外文翻译及原文 (文档含英文原文和中文翻译) 【原文一】 CONCURRENT DESIGN OF PLASTICS INJECTION MOULDS Abstract The plastic product manufacturing industry has been growing rapidly in recent years. One of the most popular processes for making plastic parts is injection moulding. The design of injection mould is critically important to product quality and efficient product processing. Mould-making companies, who wish to maintain the competitive edge, desire to shorten both design and manufacturing leading times of the by applying a systematic mould design process. The mould industry is an important support industry during the product development process, serving as an important link between the product designer and manufacturer. Product development has changed from the traditional serial process of design, followed by manufacture, to a more organized concurrent process where design and manufacture are considered at a very early stage of design. The concept of concurrent engineering (CE) is no longer new and yet it is still applicable and relevant in today’s manuf acturing environment. Team working spirit, management involvement, total design process and integration of IT tools are still the essence of CE. The application of The CE process to the design of an injection process involves the simultaneous consideration of plastic part design, mould design and injection moulding machine selection, production scheduling and cost as early as possible in the design stage.
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具零件名称中英文对照一览表 零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY 母模板CAVITY PLATE 公模仁CORE 公模板CORE PLATE 母模入子CAVITY INSERT 模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN 上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT 下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN 隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT 母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN 公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN 流道板RUNNER PLATE 流道开关RUNNER SHUT OFF 定位环LOCATING RING T 形块T GIB 注口衬套SPRUE BUSHNG U 形块U GIB 导柱LEADER PIN 拉料销SPRUE PULLER PIN 导套LEADER BUSHING 定位销DOWEL PIN 顶板导柱GUIDE PIN 顶针EJECTOR PIN 顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE 小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK 支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER 定位块INTERLOCKS 斜销座ANGLE LIFTER BASE 定位柱LOCATION PILLAR 引导块GUIDE BLOCK 开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER 弹簧SPRING 冷却棒THERMAL PIN 运输板PL LOCK O 形环O RING
附录A1（中英文对照表-零件类1） 中文名称英文名称中文别称 1. 零件类（模板） 模架mold base 模胚 隔热板thermal insulation board 定模座板top clamping plate 定模底板、面板 热流道板hot runner manifold 分流板 推流道板runner stripper plate 脱料板、水口推板、水口板型腔固定板cavity plate 定模板、定模框、A板、母模推件板stripper plate 脱模板 型芯固定板core plate 动模板、动模框、B板、公模支承板support plate 垫板、托板 垫块spacer block 模脚、方铁、登仔 推杆固定板ejector retainer plate 顶针固定板、面针板推板ejector plate 推顶杆板、顶针垫板、底针板动模座板bottom clamping plate 动模底板、底板 2. 零件类（浇注系统） 定位圈locating ring 定位环、法蓝 浇口套sprue bushing 浇口衬套、唧咀、唧嘴 浇口镶块gating insert 入水镶件 拉料杆sprue puller 拉料销、水口勾针 热流道系统hot runner system 流道板runner plate 温流道板warm runner plate 分流锥sprue spreader 二级喷嘴secondary nozzle 鱼雷形组合体torpedo body assembly 管式加热器cartridge heater 筒式加热器热管heat pipe 导热管 加热圈heating ring 热电偶thermocouple 探针、探温针 阀式热嘴valve gating nozzle 阀针式热嘴、阀节喷嘴阀针valve pin 热嘴hot nozzle 热喷嘴 热嘴垫圈nozzle seat 3. 零件类（顶出系统） 推杆ejector pin 顶杆、顶针 带肩推杆shouldered ejector pin 阶梯推杆、台阶顶针扁推杆flat ejector pin 扁顶杆、扁顶针 推管ejector sleeve 司筒、顶管、套筒 推管芯子ejector sleeve pin 中心销、司筒针
Landed plunger mold有肩柱塞式模具Burnishing die 挤光模 Landed positive mold 有肩全压式模具Button die镶入式圆形凹模 Loading shoe mold料套式模具Center-gated mold中心浇口式模具Loose detail mold 活零件模具 Chill mold 冷硬铸模 Loose mold 活动式模具 Cold hobbing冷挤压制模 Louvering die百叶窗冲切模Composite dies 复合模具 Manifold die分歧管模具 Counter punch反凸模 Modular mold 组合式模具 Double stack mold 双层模具 Multi-cavity mold多模穴模具Electroformed mold电铸成形模 Multi-gate mold复式浇口模具Expander die 扩径模 Offswt bending die双折冷弯模具Extrusion die 挤出模 Palletizing die 叠层模 Family mold反套制品模具 Plaster mold 石膏模 Blank through dies漏件式落料模Porous mold 通气性模具Duplicated cavity plate复板模Positive mold全压式模具 Fantail die扇尾形模具 Pressure die压紧模 Fishtail die鱼尾形模具 Profile die轮廓模 Flash mold 溢料式模具Progressive die顺序模 Gypsum mold 石膏铸模 Protable mold 手提式磨具 Hot-runner mold热流道模具Prototype mold 雏形试验模具 Ingot mold钢锭模 Punching die 落料模 Lancing die 切口模 Raising (embossing) 压花起伏成形Re-entrant mold 倒角式模具
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
Mold & die components 模具单元 Mold changing systems 换模系统 Mold core 模芯 Mold heaters/chillers 模具加热器/冷却器 Mold polishing/texturing 模具打磨/磨纹 Mold repair 模具维修 Molds 模具 Pressing dies 压模 Quick die change systems 速换模系统 Quick mold change systems 快速换模系统三、模具 塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base 定模座板Top clamping plate Top plate Fixed clamp plate 水口推板stripper plate A板A plate B板B plate 支承板 support plate 方铁 spacer plate 底针板 ejector plate 面针板 ejector retainer plate 回针 Return pin 导柱 Guide pin 有托导套 Shoulder Guide bush 直导套 Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin 单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss 合模力mould clamping force
DFM常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但 在浇口附近可以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点（银色斑点） 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。 16.Make sure the core float plate was closed before lifter completely return to correct position 确认 lifter完全回位时core侧浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确 位置。 19.Propose to add draft on slider side wall and draw polish. 建议增加 slider的角度和抛光角度。 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该 处壁厚过薄而造成很难去填充完整，薄壁将会有产品功能上的风险。 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印， 建议在该处减胶。 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否
冲模stamping die 冲裁模blanking die 落料模blanking die 冲孔模piercing die 修边模trimming die 切口模notching die 切口模lancing die 剖切模parting die 精修模shaving die 精冲fine blanking die 切断模cut-off die 弯曲模bending die 预弯模pre-bending die 卷边模curling die 扭曲模twisting die 拉伸模drawing die 反拉伸模reverse redrawing die 正拉伸模obverse redrawing die 变薄拉伸ironing die 成形模forming die 胀形模bulging die 压筋模stretching die 翻边模flanging die 翻孔模burring die 缩口模necking die 扩口模flaring die 整形模restriking die 压印模printing die 复合模compound die 正装复合模obverse… 倒装复合模inverse… 级进模progressive die 单工序模single-operation die 无导向模open die 导板模guide plate die 导柱模guide pillar die 通用模universal die 自动模automatic die 组合冲模combined die 传递模transfer die 镶块模insert die 柔性模flexible die 多功能模multifunction die 简易模low-cost die 橡胶冲模rubber die 钢带模steel strip die 低熔点合金模low-melting-point al 薄板模laminate die 夹板模template die 校平模planishing die 齿形校平模roughed.. 硬质合金模carbide die 上模upper die 下模lower die 模架die set 通用模架universal die set 快换模架quick change die set 后侧导柱模架back-pillar die set 对角导柱模架diagonal-pillar die set 精冲模架fine blanking die set 滑动导向模架sliding guide die set 滚动导向模架ball-bearing die set 工作零件working component 凸模punch 定距侧刃pitch punch 凸凹模main punch 镶件insert 拼块section 软模soft die 定位零件locating component 定位销locating pin 定位板locating plate 挡料销stop pin 始用挡料销finger stop pin 导正销pilot pin 抬料销Lifter pin 导料板stock guide rail 侧刃挡块stop block for pitch punch 止退键stop key 侧压板Side-push plate . 限位块limit block 限位柱limit post 压料clamping 卸料stripping 送料feeding 卸料版stripper plate 固定卸料板fixed stripper plate 弹性卸料板spring stripper plate 推件块ejector block 顶件块kicker block 顶杆kicker pin 推板ejector plate 推杆ejector pin 连接推杆ejector tie rod 打料杆knock-out pin
模具名词中英文对照表 序号中文名英文名 1 一、水口gate 2 进水位gate location 3 水口形式gate type 4 大水口edge gate 5 细水口pin-point gate 6 水口大小gate size 7 转水口switching gate 8 唧嘴口径sprue diameter 9 二、流道runner 10 热流道hot runner 11 冷流道cold runner 12 唧嘴直流direct sprue gate 13 圆形流道round runner 14 模流分析mold flow analysis 15 流道平衡runner balance 16 热嘴hot sprue 17 热流道板hot manifold 18 发热管cartridge heater 19 探针thermocouples 20 插头connector plug 21 插座connector socket 22 密封/封料seal 23 三、运水water line 24 喉塞line pug 25 喉管tube 26 塑胶管plastic tube 27 快速接头jiffy quick connector plug 28 四、模具零件mold components 29 三板模three-plate mold
模具名词中英文对照表 序号中文名英文名 30 二板模two-plate mold 31 边钉/导边leader pin/guide pin 32 边司/导套bushing/guide bushing 33 顶针板ejector retainer plate 34 托板support plate 35 螺丝screw 36 管钉dowel pin 37 开模槽ply bar score 38 内模管位core/cavity inter-lock 39 顶针ejector pin 40 司筒ejector sleeve 41 司筒针ejector pin 42 推板stripper plate 43 缩呵movable core 44 扣机（尼龙拉勾）nylon latch lock 45 斜顶lifter 46 模胚（架）mold base 47 母模cavity insert 48 公模core insert 49 行位（滑块）slide 50 镶件insert 51 压座/斜鸡wedge 52 耐磨板/油板wedge wear plate 53 压条plate 54 撑头support pillar 55 唧嘴sprue bushing 56 挡板stop plate 57 定位圈locating ring 58 锁扣latch 模具名词中英文对照表 序号中文名英文名
模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level
材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner V ents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug
模具常用术语中英文对照 模具常用术语中英文对照 中文英文 模芯Parting Core 局部视图Partial View 冷料# ColdSllig 线切割Wire E.D.M 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针AnglePin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机SpecificPress 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-LeaderdPin 镶件Mold Insert 加硬Hapden 唧嘴Sprue 设计筒图DesignPreliminary 名称块表 Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试LeakTest 流道排气Runner Vents 抛光Draw Polish 侧抽芯SideAction 中文英文加强筋Reinforcing 三角撑Gusset 柱子Bosse 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handl Ing Hole 运输安全带Moldstrap 码
模槽ClampSlot
撑头Support Pillar 螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位LeaderPin Location 耐落胶Teflon Paste 偏移量Offset 水塞 Water Line Plig 撬模脚PpySlot 重新加工Reworked 配件Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer 模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline 压机 Press 晒纹 Texturing 梯形Trapezoio 凸缘、法兰Flange 模具常用术语中英文对照 中文英文 方铁 SpacerBlock 顶针板 Ejector Plate