XXXXIsilon IQ集群安装和维护手册
XXXX
Isilon 集群安装和维护手册
目录
1. XXXX安装设定总览表 (3)
2. Isilon 的硬件安装 (4)
2.1. 前面板和铰链的安装 (4)
2.2. 滑轨的安装 (6)
3. 构建Isilon 集群 (8)
3.1. 配置集群初始节点 (8)
3.2. 将新节点加入构建好的集群 (14)
4. Isilon 后期设置 (16)
4.1. 增加所需用户和组 (16)
4.2. 设置NFS导出（共享） (17)
4.3. 设置CIFS导出（共享） (18)
4.4. DNS服务器设定修改 (20)
4.5. 客户端设置 (22)
5. Isilon 日常维护手册 (24)
5.1. 关闭节点/集群 (24)
5.2. 替换硬盘 (25)
5.3. 替换电源 (28)
5.4. 替换电池 (28)
5.5. 长期断电电池电量不足的处理方法 (29)
6. Isilon 后续添加节点说明 (30)
1. XXXX安装设定总览表集群部分
网络设定部分
文件共享部分
2. Isilon 的硬件安装2.1. 前面板和铰链的安装安装左，右铰链支架到机器上
将前面板和左右铰链支架用螺丝固定
连接显示线缆和前面板的PC板
2.2. 滑轨的安装
抽出滑轨最内侧的轨道
将内侧滑轨安装到Isilon 节点上
将导轨固定在机柜上
安装Isilon 节点到滑轨上
给Isilon 节点加电
3. 构建Isilon 集群
3.1. 配置集群初始节点
用串口线连接一台电脑和Isilon 节点的管理端口
在电脑上打开“超级终端”程序
配置串口连接的设置
Transfer rate: 9600 bps — IQ 1440/2250 models
115,200 bps — IQ 1920/3000/6000/9000 and IQ Accelerator models
115,200 bps — IQ 1920x/3000x/6000x/9000x
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware
提示符下创建root和admin账户和密码
接下来，将被询问是否收集报警信息
“Would you like to allow Isilon Systems, Inc. to receive critical alerts from
this cluster? [no]”
Isilon 的配置向导自动打开
Do you wish to
[1] create a new cluster.
[2] join an existing cluster.
[3] exit wizard and configure manually.
Wizard >>>
创建集群
Do you wish to
[1] create a new cluster.
[2] join an existing cluster.
[3] exit wizard and configure manually.
Wizard >>> 1
>>> 1 create a new cluster.
按提示配置集群
1）Type a new name for the cluster.
Set Name >>> isilon
Cluster name set to 'isilon'
2）Cluster Encoding:
[1] Windows-SJIS
[2] Windows-949
[3] Windows-1252
[4] EUC-KR
[5] EUC-JP
[6] EUC-JP-MS
[7] UTF-8-MAC
[8] UTF-8
[9] ISO-8859-1 (Latin-1)
[10] ISO-8859-2 (Latin-2)
[11] ISO-8859-3 (Latin-3)
[12] ISO-8859-4 (Latin-4)
[13] ISO-8859-5 (Cyrillic)
[14] ISO-8859-6 (Arabic)
[15] ISO-8859-7 (Greek)
[16] ISO-8859-8 (Hebrew)
[17] ISO-8859-9 (Latin-5)
[18] ISO-8859-10 (Latin-6)
[19] ISO-8859-13 (Latin-7)
[20] ISO-8859-14 (Latin-8)
[21] ISO-8859-15 (Latin-9)
[22] ISO-8859-16 (Latin-10)
[Enter] Use default encoding: UTF-8 Set Encoding >>>
3）Configure interface int-a:
[1] Configure Netmask
[2] Modify IP Ranges
[Enter] Keep the current configuration:
Netmask: unset
IP Ranges: No ranges set. Configure Interface int-a >>> 1
4）Type a new netmask.
Set int-a Netmask >>> 255.255.255.0
int-a Netmask set to '255.255.255.0'
5）Configure interface int-a:
[1] Configure Netmask
[2] Modify IP Ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP Ranges: No ranges set.
Configure Interface int-a >>> 2
6）Manage cluster IP ranges
[ 1] Add an IP range.
[ 2] Delete an IP range.
[Enter] Keep current IP ranges: No ranges set.
Modify int-a IP Ranges >>> 1
7）Enter the low IP address of the range to add.
Low IP Address (Add) >>> 10.10.10.1
Enter the high IP address of the range.
High IP Address (Add) >>> 10.10.10.3
IP range added.
8）Manage cluster IP ranges
[ 1] Add an IP range.
[ 2] Delete an IP range.
[Enter] Keep current IP ranges: '10.10.10.1 – 10.10.10.3' Modify int-a IP Ranges >>>
int-a IP ranges configured.
9）Configure interface int-a:
[ 1] Configure Netmask
[ 2] Modify IP Ranges
[Enter] Keep the current configuration:
Netmask: 255.255.255.0
IP Ranges: '10.10.10.1 – 10.10.10.3' Configure Interface int-a >>>
10）Select the internal interface to configure.
[ 1] int-a - Primary Internal Interface
[ 2] int-b - Secondary Internal Interface (Failover)
[Enter] Finished with internal interfaces Configure Internal Interfaces >>>
11）Configure External Subnet
[ 1] Configure ext-1
[Enter] Finished configuring External Subnet Configure External Subnet >>> 1
12）Configure ext-1
Configure ext-1 settings
[ 1] Set Netmask
[ 2] Set MTU
[ 3] Set IP Ranges
[Enter] Keep the current settings:
Netmask: unset
MTU: 1500
IP Ranges: No ranges set
Configure ext-1 settings >>> 1
13) Set Netmask for ext-1
Type the netmask:
ext-1 netmask >>> 255.255.255.0
14) Configure ext-1 settings
[ 1] Set Netmask
[ 2] Set MTU
[ 3] Set IP Ranges
[Enter] Keep the current settings:
Netmask: 255.255.255.0
MTU: 1500
IP Ranges: No ranges set
Configure ext-1 settings >>> 3
15) Set IP Ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep current IP ranges: No ranges set
Set IP Ranges for ext-1 >>> 1
16) Add an IP range
Type the low IP address of the range to add:
>>> 10.1.0.201
Type the high IP address of the range to add:
>>> 192.168.1.205
17) Set IP Ranges
[ 1] Add an IP range
[ 2] Delete an IP range
[Enter] Keep current IP ranges: 10.1.0.201 - 192.168.1.205 Set IP Ranges for ext-1 >>>
18）Configure ext-1 settings
[ 1] Set Netmask
[ 2] Set MTU
[ 3] Set IP Ranges
[Enter] Keep the current settings:
Netmask: 255.255.255.0
MTU: 1500
IP Ranges: 10.1.0.201 - 192.168.1.205 Configure ext-1 settings >>>
19）onfigure default gateway
[ 1] Set Default Gateway
[Enter] Keep current default gateway: '192.168.1.254' Configure default gateway >>>
20）Configure SmartConnect settings
[ 1] SmartConnect Zone Name
[ 2] SmartConnect Service IP
[Enter] Keep current SmartConnect settings:
SmartConnect Zone Name: 'https://www.doczj.com/doc/8a3824442.html,'
SmartConnect Service IP: '192.168.0.208' Configure SmartConnect settings >>>
21) Configure DNS settings
[ 1] Domain Name Servers
[ 2] DNS Search List
[Enter] Keep current DNS settings:
Domain Name Servers: not set
DNS Search List: not set
Configure DNS settings >>>
22) Configure External Subnet
[ 1] Configure ext-1
[Enter] Finished configuring External Subnet
Configure External Subnet >>>
23)Manage cluster date and time
[ 1] Set timezone
[ 2] Set day and time
[Enter] Keep current date and time: “not set”
Modify Date >>>
24) Manage the cluster add node setting
[ 1] Manual join
[ 2] Secure join
[Enter] Keep current add node setting: 'Manual'
Modify Add Node Setting >>>
Join mode kept as 'Manual'.
25) You have made the following configuration changes:
- Cluster name changed from unset to 'isilon'.
- Interface int-a netmask changed from unset to 255.255.255.0.
- Interface int-a IP ranges have changed from None defined.
to 10.1.0.201 - 192.168.1.205
- Encoding information changed from unset to UTF-8
- External network changed.
Do you wish to commit these changes? [yes]
Commit Changes? >>>
系统启动，进入图形界面
https:\\10.1.0.201:8080
3.2. 将新节点加入构建好的集群选择加入集群
Cluster->Hardware Configuration->add node
选择加入集群
4. Isilon 后期设置
4.1. 增加所需用户和组
Cluster->Access Management->Users /Groups
Create a user
用户没有NIS或者LDAP，增加用户wxx（uid=361，group proc, gid=592）和wzz（uid=1000，group proc, gid=592）使用Isilon集群存储上的空间
使用ssh登陆到Isilon 集群上，执行如下命令
#pw groupadd proc –g 592
#pw useradd wxx –u 361 –g proc
#pw useradd wzz –u 1000 –g proc
4.2. 设置NFS导出（共享）
在WebUI管理界面菜单栏“PROTOCALS”下的“NFS”项中配置export目录/ifs/data，将“Map root users to”设定为wxx，“Assign Groups”设定为proc
删除系统默认的/ifs的NFS导出，增加安全性
NFS共享设置
4.3. 设置CIFS导出（共享）
在WebUI管理界面菜单栏“PROTOCALS”下的“Windows Sharing”项中配置add a share目录/ifs/data，将“Map root users to”设定为wxx，“Assign Groups”设定为proc
删除系统默认的/ifs的CIFS共享，增加安全性
新建Share
4.4. 文件系统管理
在原有的/ifs/data目录下新建目录data1、data2、data3 点击File System Explorer
在data目录下新建data1、data2、data3