Argentinean plug (2)
AU Plug (3)
Brazil plug (5)
BSMI Plug (7)
CN Plug (8)
EU Plug (9)
India plug (10)
Japan plug (11)
Korea plug (12)
South Africa Plug (13)
UK Plug (14)
US Plug (15)
France Plug (16)
Thailand Plug (17)
EU Plug防水 (18)
Argentinean plug
Plug dimensions(IRAM2063:2009)
Figure1Figure2
Figure3a Figure3b
Figure4
Location Requirement Measurement Verdict Distance from pins to external
min.8mm
perimeter of the plug(A in Fig.2)
Pin Angle1)115°-125°
Pin width(a–Fig.4)–LIVE6,15mm–6,35mm
Pin width(a–Fig.4)–NEUTRAL6,15mm–6,35mm
Pin thikness(e–Fig.4)–LIVE1,48mm–1,62mm
Pin thikness(e–Fig.4)–NEUTRAL1,48mm–1,62mm
Pin length(g–Fig.4)–LIVE18,0mm–18,4mm
Pin length(g–Fig.4)-NEUTRAL18,0mm–18,4mm
Pins ends should be rounded Figs3a or3b
The plug should fit on the standardized socket-outlet
The Neutral Pin should be marked with“N”(Fig.1)
The external perimeter of the plug should not exceed44mm.
The test finger should not reach pins when still energized
In case pins have insulating sleeves,pins dimensions should be checked over the sleeves
In case pins have insulating sleeves,tests on Clause24.7should be applied
In case pins have insulating sleeves,tests on Clause30should be applied
1):This measurement should be marked as PASS if the plug fits on the standardized socket-outlet
AU Plug
Dimension Checking for Two-pin plugs (Up to 10A rating,250V max.)According to AS/NZS 3112:2000
Symbol Requirement
(mm)
Measured (mm)Symbol Requirement
(mm)
Measured (mm)
A <21.9or >27.0H 1.58–1.78
B <21.9or >27.0I 16.66–17.46
C <21.9or >27.0J >8.6
D <21.9or >27.0
K G 7.92 Symbol Requirement (mm)Measured(mm)Symbol Requirement (mm) Measured(mm) For insulated pin type 8.2–9.28.8 Brazil plug per NBR14136/02–FIGURE13 Dimensions Plugs shall comply with Standard Sheet NBR14136/02–FIGURE13 Item no.Location Requirement Measurement A)Diagonal dimension of plug base 26±0.5mm Top③ mm B)Length of plug base 35.5±0.5mm Top③ mm C)Width of plug base14±0.5mm Top③mm D)Between two pins19±0.2mm mm E)Chamfer radius of plug base R5+1mm mm F)Angle of two diagonal surface90°+2° G)Chamfer radius of plug side face R1mm max.mm H)Diameter of pin(metallic part in sleeve)2.8mm min. mm I)Thickness of insulating sleeve 0.3mm min. mm J)No sharp edge K)Length of pin except metal part10+1.0mm mm L)Pin length19+0.7mm mm M)Diameter of pin(metallic part)4±0.05mm mm N)Radius of pin top R2+0.5mm mm ①The distance between the engagement face and the cord or cord guard,if any,shall be at least14mm 14mm min. mm ②Within this distance(5mm),the outline shall be not smaller than the engagement face ③Within this distance(13.5mm),the outline shall be not larger than the engagement face ④Insulating sleeves on the current-carrying pins are optional ⑤The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins ⑥To avoid damage to shutters,the ends of the pins shall show neither sharp edges nor burrs. They shall be of rounded shape as shown ⑦The angle of90°represents the maximum permissible area for the orientation of the entry of the flexible cable or cord BSMI Plug CNS 690(民國87年修訂版) 章節 要求—試驗 結果—備考 判定 3.種類、極數、極型及定額 依「表1」規定,附花線者應符合CNS 9827標準。 2極15A 125V 符合4.9刃片安裝部強度: —4.9.1以鉚釘或螺絲固定刃片,且其外型輪廓為圓形者,依CNS 3907第3.10.1節試驗,不得破壞刃片安裝部。 不適用4.9.2除上述品外,其外型輪廓亦應為符合圓型或平型者,依CNS 3907第3.10.1節試驗,刃片不得脫出安裝部。符合4.9.3 一體成型者,需符合下列規定: —(1)依CNS 3907第3.10.3(1)節試驗,刃片彎曲所需作用力應為4kgf 以上。 符合(2)依CNS 3907第3.10.3(2)節試驗,刃片不得破裂,安裝部外殼不受破壞。 符合(3)依CNS 3907第3.10.3(3)節試驗,刃片不得破裂。 符合5.6 刃片與刃座之形狀及尺度:依附圖1~4規定(掛裝型除外)附圖1(1) 符合 ±單位:mm A B C (1) D E F G H I J K 標示值 6.3±0.3 1.5±0.1 8±0.2 14.6max 12.7 10.8min 17±1.311.7±0.4ψ3.5min ψ3 +0.3 0.9max -0.2 量測值 註(1):無極性之刃片寬度同A 尺寸要求。 A B C (1) D F E G H 附圖 1(1) 實心刃片 曲形刃片 I J K I J Symbol F t b E R Measured (mm) EN 50075 Dimensions –Standard Sheet 1 Symbol Requirement (mm) Measured (mm)Symbol Requirement (mm) Measured (mm) A ≥16.5H 1)≤3.8 B 25.6–26.6 J 3.94–4.06C 45?K 10.0–11.0D R 5.0–6.0L 18.5–19.5E 34.6–36.0M ≤90?F 13.0–14.4N 0.7–1.7G Engagement face 18.0–19.2 O ≤2.0 1)This dimension may be increased to 4mm within a distance of 4mm from the engagement face of the plug. G End of pins 17.0–18.0 Symbol Rated Current Measured(mm)Verdict ()8A()16A A22.228.6 B19.125.4 C7.010-7.0858.66-8.735 D 5.030-5.1057.010-7.085 E15.77-16.9420.47-21.64 F20.47-21.6428.47-29.64 G7.94min.9.52min. H2) 5.16-7.54 6.76-9.12 J3)27.232.3 Note: H:Distance between the base of plug and socket-outlet at position of first contact of live pins. Per JIS C8303or IEC60083 Measured dimensions of the plug portion(per JIS C8303or IEC60083) Location Measured dimensions(mm) Limit of dimensions(mm) Sample1Sample2Sample3 A Under14,6 B Over10,8 C1,5±0,1 D6,3±0,3 E8±0,2 F?3+0,3/-0,2 G Over?3,5 H11,7±0,4 J17±1,3 Notes: 1)In case of those without having distinction of polarity,the width of blade shall be6,3mm±0,3mm. (Two-pole plug for3A250V)According to KSC8305 Symbol Requirement(mm)Measured(mm)Symbol Requirement(mm)Measured(mm) A Max.90?Q 3.3~4.3? B Max.3R Min.6? C Max.φ2.5S25.6~26.6 Dφ36.0~φ37.0T13.0~14.4 E18.8~19.2U18.8~19.2 F R3.0~R3.3V34.6~36.0 G 3.5~4.5W R5~R6 H Min.5X45? I31.5~32.5Y Min.4 J9.9~10.1Z4 K9.9~10.1A110.0~11.0 L Min.16.5B118.5~19.5 M Min.17.5C1φ4.74~φ4.86 N18.5~19.5D1Max.4.3 O Min.15.5E1 4.4~4.8 Pφ4.794~φ4.806 South Africa Plug Drawing of Plug Symbol Rated Current Measured (mm) ()2A ()5A ()15A A 14.4822.2228.58B 14.4819.0525.4C 5.05-5.17.04-7.098.69-8.74D 3.53-3.58 5.05-5.17.04-7.09E 12.57-13.7415.75-16.9220.5-21.67F 15.75-16.92 20.5-21.6728.45-29.62 G 1) 6.357.949.52H 2) 3.58-5.94 5.16-7.54 6.76-9.12J 3) 19.3 27.2 32.3 Note: 1.“G”is the minimum distance between the pins and the periphery of the plug. 2.“H”is the distance between the front surface of the plug and the socket-outlet at position of first contact of live pins. 3.“J”is the radius of the maximum permissible plug contour.The radius is concentric with the pitch circle radius of the pins . Dimensions Check according to Figure 4of BS 1363-1 Symbol Requirement (mm)Measured (mm) Symbol Requirement (mm)Measured (mm) A 25.37max.21.42Q 17.2-18.217.85 B 25.37max.21.42R 6.22-6.48 6.36 C 34.6max.32.52S 3.90-4.05 4.18 D 11.05-11.1811.08T 6.22-6.48 6.42 E 11.05-11.1811.08U 6.35min. F R 15min.14.71 V 60?-80?G R 9.5min.W 1.35-1.85H R 9.5min.X 3.90-4.05 3.92 I 22.10-22.36Y 1.2-2.0J 22.23-23.2322.02Z R 0.1-1.0K 1.35-1.85a 58?-62?L 7.80-8.058.27b 1.35-1.85M 58?-62?c 58?-62?N 3.90-4.05 3.97d 1.35-1.85O 9.2max.8.40e 0.2max.P 9.5max. 9.45 f 1.35-1.85 Location Limited Measured (inch) Verdict A >=5.1mm B 0.625–0.718(inch)15.87-18.23(mm)C 0.240–0.260(inch)0.609-6.6(mm)D 0.055–0.065(inch)1.39-1.65(mm)E 0.307–0.322(inch)7.79-8.17(mm)F 0.500(inch)12.7(mm) B C D E A F France Plug Thailand Plug EU Plug防水