Avionics common p
1.Aviation electronic maintenance personnel in daily work will come in contact with
welding Tools (Crimp Tools).Here are several kind of common pressure welding tools for introduction operation of tools will also make an introduction.
2.Basically, most of the pressure welding tools are through the control precision ratchet so as to contr
Common pressu
NO.Tool Name Version Diagram
1AF8M22520/1-01
2AFM8M22520/2-01 3Module 钳M10S-1
4 AD-1377 5AMP 59250 6AMP46063
7KTH1000
Introduction Operation method
AF8 is an accord with the us military standard MIL - DTL - 22520/1 of the adjustable pressure needle tool, by DMC production. Suitable for
AWG12 - and all kinds of common pin. 1. AF8 can and a variety of locating piece adapter (TH series, TM system column, TP series or general locating piece UH2-5), in order to adapt to different pin and the requirements of the conductor.
2. AF8 to pin the crimping strength (can determine its resistance to tension degree) is by itself with a eight choose knob to control. For different AWG wires, its corresponding pressure welding strength value can be read in locating piece.
It can be through the rotating tower type locating piece, to adapt to different types of pin or different sizes of pin, so as to avoid frequent replacement locating piece.1. Pressure welding, the tool handle must press to completely accept joint position, makes the ratchet complete a cycle, can loose open.
2. Tower type locating piece replacement:
2.1. Ensure that AF8 in full open position, use hex wrench screw pinecone type locating piece on the Allen screw (2), the tower type locating piece from the retaining ring release, remove the tower type locating piece when attention must be perpendicular to the fixed ring out.
2.2. Ensure that AF8 in full open position, and open tower type locating piece of loosen the trigger, make tower type locating piece in a shift position. 2.
3. The tower type locating piece fixed in the fixed ring after, with hex wrench will tower type locating piece of the Allen screw tightening.
mon pressure welding tool brief introduction t with all sorts of conductor and pin，and need to use all kinds of pressure ure welding tools for introduction，So that you know these tools.As for the specific
ol precision ratchet so as to control every pressure welding precision,belong to high essure welding Tools (Crimp Tools) profile
AFM8 is a kind of character close American army MIL - DTL - 22520/2 standard small adjustable voltage needle tool. Suitable for AWG20-32 various common pin. And AF8, AFM8 with various locating piece with work, so as to adapt to the requirements of different pin.
AFM8 to pin the crimping strength is the body with the one of the eight choose knob to control. For different AWG wires, which should be to the pressure welding strength value can be in the corresponding set a piece of a read.1. Pressure welding, the tool of the two handle must press to completely accept joint position, make ratchet complete a cycle, and then you can loosen the handle. 2. Replace locating piece, need to pin locating piece and rotate 90 degrees, then pulled out, can remove the locating piece.
3. Installation locating piece, must first will locate block insert fixed ring (note: fixed ring and locating piece two bayonet pin direction can be inserted before), and then press the locating piece and rotate 90 degrees, which can be installed good locating piece.
4.
AFM8 replacement locating piece, the tool must be in the fully open position.
5. Note: daily work, AF8 and AFM8 is the most commonly used pressing tools (CONTACT CRIMP TOOL). In each of the plug should be positioning block specific part number or type can be made by SWPM seized.
AF8 and AFM8 without special maintenance, need to pay attention to is not for the clean liquid or try to use the tool to lubrication oil.
M10S - 1 is also a kind of pressure needle tool, commonly known as Module forceps, just as its name implies, is used to pressure welding Module needle tool.
Module clamp is a relatively simple tools, so do not do this way is introduced.
Dedicated to pressure welding with MIL - S - 81824/1. / 2 & / 3 (such as: D436-36, 37, & and standard of the connection pipe, that is used for pressure welding figure 6 shows the sealing connection tube (the connection tube is mainly suitable for no shielding layer of wire or cable)When using must pay attention to: the chosen pressure welding groove color must and connection pipe is the same color. AD - 1377 also is to belong to through the control ratchet to achieve precision pressure welding tool. Pressure welding must be will handle press to full charge $location can loosen.
1. Because of its handle color is BLUE, one RED and the other is commonly known as RED and BLUE forceps (RED BLUE CRIMPER).
2. Mainly used for pressure welding all kinds of T type terminal lug (often used for grounding), waterproof connection tube (not seal), END CAP. AMP59250 is also through the ratchet to control pressure welding precision. only Upon completion of a pressure welding cycle (the handle press to full close upper set), can loosen the handle.
3. Parts is introduced: A: pressure welding strength choice (1-4 level) B: positioning device C: color code information D: trigger, under pressure to press the two handle 1. Pressure welding, must first press the red handle next to the trigger can't pressure welding. Suitable for AWG14-22 of the conductor. 2. Pressure welding finished, can from the pressure welding of lug or connection pipe outside Insulating layer on the identification of the corresponding point CODE (DOT CODE), thus judgment is no pressure welding correctly and in place. (see table 1)
Mainly used for END CAP pressure welding. AMP46063 head all pressure JieQiang corresponding scale There are red, blue, yellow point, and the pressure welding of the END CAP layer color mutual correspondence.
Used for pressure welding all kinds of coaxial cable BNC or TNC joint. KTH1000 need and pressure welding block (DIE) cooperate with work For. Different types of coaxial cable joint used pressure welding block is not the same. Pressure welding block side used to pressure welding coaxial cable joint In the central pin, the other side with to pressure welding K - GRIP casing.
on
Diagram
DOT CODE
DIE