外语文献翻译
摘自: 《制造工程与技术（机加工）》（英文版）
《Manufacturing Engineering and Technology —Machining 》
机械工业出版社 2004年3月第1版 页—564560P
美 s. 卡尔帕基安(Serope kalpakjian)
s.r 施密德(Steven R.Schmid) 著
原文：
20.9 MACHINABILITY
The machinability of a material usually defined in terms of four factors:
1、
Surface finish and integrity of the machined part; 2、
Tool life obtained; 3、
Force and power requirements; 4、 Chip control.
Thus, good machinability good surface finish and integrity, long tool life, and low force And power requirements. As for chip control, long and thin (stringy) cured chips, if not broken up, can severely interfere with the cutting operation by becoming entangled in the cutting zone.
Because of the complex nature of cutting operations, it is difficult to establish relationships that quantitatively define the machinability of a material. In
manufacturing plants, tool life and surface roughness are generally considered to be the most important factors in machinability. Although not used much any more, approximate machinability ratings are available in the example below.
20.9.1 Machinability Of Steels
Because steels are among the most important engineering materials (as noted in Chapter 5), their machinability has been studied extensively. The machinability of steels has been mainly improved by adding lead and sulfur to obtain so-called free-machining steels.
Resulfurized and Rephosphorized steels. Sulfur in steels forms manganese sulfide inclusions (second-phase particles), which act as stress raisers in the primary
shear zone. As a result, the chips produced break up easily and are small; this improves machinability. The size, shape, distribution, and concentration of these inclusions significantly influence machinability. Elements such as tellurium and selenium, which are both chemically similar to sulfur, act as inclusion modifiers in resulfurized steels.
Phosphorus in steels has two major effects. It strengthens the ferrite, causing increased hardness. Harder steels result in better chip formation and surface finish. Note that soft steels can be difficult to machine, with built-up edge formation and poor surface finish. The second effect is that increased hardness causes the formation of short chips instead of continuous stringy ones, thereby improving machinability.
Leaded Steels. A high percentage of lead in steels solidifies at the tip of manganese sulfide inclusions. In non-resulfurized grades of steel, lead takes the form of dispersed fine particles. Lead is insoluble in iron, copper, and aluminum and their alloys. Because of its low shear strength, therefore, lead acts as a solid lubricant (Section 32.11) and is smeared over the tool-chip interface during cutting. This behavior has been verified by the presence of high concentrations of lead on the
tool-side face of chips when machining leaded steels.
When the temperature is sufficiently high-for instance, at high cutting speeds and feeds (Section 20.6)—the lead melts directly in front of the tool, acting as a liquid lubricant. In addition to this effect, lead lowers the shear stress in the primary shear zone, reducing cutting forces and power consumption. Lead can be used in every grade of steel, such as 10xx, 11xx, 12xx, 41xx, etc. Leaded steels are identified by the letter L between the second and third numerals (for example, 10L45). (Note that in stainless steels, similar use of the letter L means “low carbon,” a condition that improves their corrosion resistance.)
However, because lead is a well-known toxin and a pollutant, there are serious environmental concerns about its use in steels (estimated at 4500 tons of lead consumption every year in the production of steels). Consequently, there is a continuing trend toward eliminating the use of lead in steels (lead-free steels). Bismuth and tin are now being investigated as possible substitutes for lead in steels.
Calcium-Deoxidized Steels. An important development is calcium-deoxidized steels, in which oxide flakes of calcium silicates (CaSo) are formed. These flakes, in turn, reduce the strength of the secondary shear zone, decreasing tool-chip interface
and wear. Temperature is correspondingly reduced. Consequently, these steels produce less crater wear, especially at high cutting speeds.
Stainless Steels. Austenitic (300 series) steels are generally difficult to machine. Chatter can be s problem, necessitating machine tools with high stiffness. However, ferritic stainless steels (also 300 series) have good machinability. Martensitic (400 series) steels are abrasive, tend to form a built-up edge, and require tool materials with high hot hardness and crater-wear resistance. Precipitation-hardening stainless steels are strong and abrasive, requiring hard and abrasion-resistant tool materials.
The Effects of Other Elements in Steels on Machinability. The presence of aluminum and silicon in steels is always harmful because these elements combine with oxygen to form aluminum oxide and silicates, which are hard and abrasive. These compounds increase tool wear and reduce machinability. It is essential to produce and use clean steels.
Carbon and manganese have various effects on the machinability of steels, depending on their composition. Plain low-carbon steels (less than 0.15% C) can produce poor surface finish by forming a built-up edge. Cast steels are more abrasive, although their machinability is similar to that of wrought steels. Tool and die steels are very difficult to machine and usually require annealing prior to machining. Machinability of most steels is improved by cold working, which hardens the material and reduces the tendency for built-up edge formation.
Other alloying elements, such as nickel, chromium, molybdenum, and vanadium, which improve the properties of steels, generally reduce machinability. The effect of boron is negligible. Gaseous elements such as hydrogen and nitrogen can have particularly detrimental effects on the properties of steel. Oxygen has been shown to have a strong effect on the aspect ratio of the manganese sulfide inclusions; the higher the oxygen content, the lower the aspect ratio and the higher the machinability.
In selecting various elements to improve machinability, we should consider the possible detrimental effects of these elements on the properties and strength of the machined part in service. At elevated temperatures, for example, lead causes embrittlement of steels (liquid-metal embrittlement, hot shortness; see Section 1.4.3), although at room temperature it has no effect on mechanical properties.
Sulfur can severely reduce the hot workability of steels, because of the formation of iron sulfide, unless sufficient manganese is present to prevent such formation. At
room temperature, the mechanical properties of resulfurized steels depend on the orientation of the deformed manganese sulfide inclusions (anisotropy). Rephosphorized steels are significantly less ductile, and are produced solely to improve machinability.
20.9.2 Machinability of Various Other Metals
Aluminum is generally very easy to machine, although the softer grades tend to form a built-up edge, resulting in poor surface finish. High cutting speeds, high rake angles, and high relief angles are recommended. Wrought aluminum alloys with high silicon content and cast aluminum alloys may be abrasive; they require harder tool materials. Dimensional tolerance control may be a problem in machining aluminum, since it has a high thermal coefficient of expansion and a relatively low elastic modulus.
Beryllium is similar to cast irons. Because it is more abrasive and toxic, though, it requires machining in a controlled environment.
Cast gray irons are generally machinable but are. Free carbides in castings reduce their machinability and cause tool chipping or fracture, necessitating tools with high toughness. Nodular and malleable irons are machinable with hard tool materials.
Cobalt-based alloys are abrasive and highly work-hardening. They require sharp, abrasion-resistant tool materials and low feeds and speeds.
Wrought copper can be difficult to machine because of built-up edge formation, although cast copper alloys are easy to machine. Brasses are easy to machine, especially with the addition pf lead (leaded free-machining brass). Bronzes are more difficult to machine than brass.
Magnesium is very easy to machine, with good surface finish and prolonged tool life. However care should be exercised because of its high rate of oxidation and the danger of fire (the element is pyrophoric).
Molybdenum is ductile and work-hardening, so it can produce poor surface finish. Sharp tools are necessary.
Nickel-based alloys are work-hardening, abrasive, and strong at high temperatures. Their machinability is similar to that of stainless steels.
Tantalum is very work-hardening, ductile, and soft. It produces a poor surface
finish; tool wear is high.
Titanium and its alloys have poor thermal conductivity (indeed, the lowest of all metals), causing significant temperature rise and built-up edge; they can be difficult to machine.
Tungsten is brittle, strong, and very abrasive, so its machinability is low,
although it greatly improves at elevated temperatures.
Zirconium has good machinability. It requires a coolant-type cutting fluid,
however, because of the explosion and fire.
20.9.3 Machinability of Various Materials
Graphite is abrasive; it requires hard, abrasion-resistant, sharp tools.
Thermoplastics generally have low thermal conductivity, low elastic modulus, and low softening temperature. Consequently, machining them requires tools with positive rake angles (to reduce cutting forces), large relief angles, small depths of cut and feed, relatively high speeds, and
proper support of the workpiece. Tools should be sharp.
External cooling of the cutting zone may be necessary to keep the chips from becoming “gummy” and sticking to the tools. Cooling can usually be achieved with a jet of air, vapor mist, or water-soluble oils. Residual stresses may develop during machining. To relieve these stresses, machined parts can be annealed for a period of time at temperatures ranging from C ?80 to C ?160 (F ?175to F ?315), and then cooled slowly and uniformly to room temperature.
Thermosetting plastics are brittle and sensitive to thermal gradients during
cutting. Their machinability is generally similar to that of thermoplastics.
Because of the fibers present, reinforced plastics are very abrasive and are
difficult to machine. Fiber tearing, pulling, and edge delamination are significant problems; they can lead to severe reduction in the load-carrying capacity of the component. Furthermore, machining of these materials requires careful removal of machining debris to avoid contact with and inhaling of the fibers.
The machinability of ceramics has improved steadily with the development of nanoceramics (Section 8.2.5) and with the selection of appropriate processing parameters, such as ductile-regime cutting (Section 22.4.2).
Metal-matrix and ceramic-matrix composites can be difficult to machine, depending on the properties of the individual components, i.e., reinforcing or whiskers, as well as the matrix material.
20.9.4 Thermally Assisted Machining
Metals and alloys that are difficult to machine at room temperature can be machined more easily at elevated temperatures. In thermally assisted machining (hot machining), the source of heat—a torch, induction coil, high-energy beam (such as laser or electron beam), or plasma arc—is forces, (b) increased tool life, (c) use of inexpensive cutting-tool materials, (d) higher material-removal rates, and (e) reduced tendency for vibration and chatter.
It may be difficult to heat and maintain a uniform temperature distribution within the workpiece. Also, the original microstructure of the workpiece may be adversely affected by elevated temperatures. Most applications of hot machining are in the turning of high-strength metals and alloys, although experiments are in progress to machine ceramics such as silicon nitride.
SUMMARY
Machinability is usually defined in terms of surface finish, tool life, force and power requirements, and chip control. Machinability of materials depends not only on their intrinsic properties and microstructure, but also on proper selection and control of process variables.
译文：
20.9 可机加工性
一种材料的可机加工性通常以四种因素的方式定义：
1、分的表面光洁性和表面完整性。
2、刀具的寿命。
3、切削力和功率的需求。
4、切屑控制。
以这种方式，好的可机加工性指的是好的表面光洁性和完整性，长的刀具寿命，低的切削力和功率需求。关于切屑控制，细长的卷曲切屑，如果没有被切割成小片，以在切屑区变的混乱，缠在一起的方式能够严重的介入剪切工序。
因为剪切工序的复杂属性，所以很难建立定量地释义材料的可机加工性的关系。在制造厂里，刀具寿命和表面粗糙度通常被认为是可机加工性中最重要的因素。尽管已不再大量的被使用，近乎准确的机加工率在以下的例子中能够被看到。
20.9.1 钢的可机加工性
因为钢是最重要的工程材料之一（正如第5章所示），所以他们的可机加工性已经被广泛地研究过。通过宗教铅和硫磺，钢的可机加工性已经大大地提高了。从而得到了所谓的易切削钢。
二次硫化钢和二次磷化钢硫在钢中形成硫化锰夹杂物（第二相粒子），这些夹杂物在第一剪切区引起应力。其结果是使切屑容易断开而变小，从而改善了可加工性。这些夹杂物的大小、形状、分布和集中程度显著的影响可加工性。化学元素如碲和硒，其化学性质与硫类似，在二次硫化钢中起夹杂物改性作用。
钢中的磷有两个主要的影响。它加强铁素体，增加硬度。越硬的钢，形成更好的切屑形成和表面光洁性。需要注意的是软钢不适合用于有积屑瘤形成和很差的表面光洁性的机器。第二个影响是增加的硬度引起短切屑而不是不断的细长的切屑的形成，因此提高可加工性。
含铅的钢钢中高含量的铅在硫化锰夹杂物尖端析出。在非二次硫化钢中，铅呈细小而分散的颗粒。铅在铁、铜、铝和它们的合金中是不能溶解的。因为它的低抗剪强度。因此，铅充当固体润滑剂并且在切削时，被涂在刀具和切屑的接口处。这一特性已经被在机加工铅钢时，在切屑的刀具面表面有高浓度的铅的存在所证实。
当温度足够高时—例如，在高的切削速度和进刀速度下—铅在刀具前直接熔化，并且充当液体润滑剂。除了这个作用，铅降低第一剪切区中的剪应力，减小切削力和功率消耗。铅能用于各种钢号，例如10XX，11XX，12XX，41XX等等。铅钢被第二和第三数码中的字母L所识别（例如，10L45）。（需要注意的是在不
锈钢中，字母L的相同用法指的是低碳，提高它们的耐蚀性的条件）。
然而，因为铅是有名的毒素和污染物，因此在钢的使用中存在着严重的环境隐患（在钢产品中每年大约有4500吨的铅消耗）。结果，对于估算钢中含铅量的使用存在一个持续的趋势。铋和锡现正作为钢中的铅最可能的替代物而被人们所研究。
脱氧钙钢一个重要的发展是脱氧钙钢，在脱氧钙钢中矽酸钙盐中的氧化物片的形成。这些片状，依次减小第二剪切区中的力量，降低刀具和切屑接口处的摩擦和磨损。温度也相应地降低。结果，这些钢产生更小的月牙洼磨损，特别是在高切削速度时更是如此。
不锈钢奥氏体钢通常很难机加工。振动能成为一个问题，需要有高硬度的机床。然而，铁素体不锈钢有很好的可机加工性。马氏体钢易磨蚀，易于形成积屑瘤，并且要求刀具材料有高的热硬度和耐月牙洼磨损性。经沉淀硬化的不锈钢强度高、磨蚀性强，因此要求刀具材料硬而耐磨。
钢中其它元素在可机加工性方面的影响钢中铝和矽的存在总是有害的，因为这些元素结合氧会生成氧化铝和矽酸盐，而氧化铝和矽酸盐硬且具有磨蚀性。这些化合物增加刀具磨损，降低可机加工性。因此生产和使用净化钢非常必要。
根据它们的构成，碳和锰钢在钢的可机加工性方面有不同的影响。低碳素钢（少于0.15%的碳）通过形成一个积屑瘤能生成很差的表面光洁性。尽管铸钢的可机加工性和锻钢的大致相同，但铸钢具有更大的磨蚀性。刀具和模具钢很难用于机加工，他们通常再煅烧后再机加工。大多数钢的可机加工性在冷加工后都有所提高，冷加工能使材料变硬并且减少积屑瘤的形成。
其它合金元素，例如镍、铬、钳和钒，能提高钢的特性，减小可机加工性。硼的影响可以忽视。气态元素比如氢和氮在钢的特性方面能有特别的有害影响。氧已经被证明了在硫化锰夹杂物的纵横比方面有很强的影响。越高的含氧量，就产生越低的纵横比和越高的可机加工性。
选择各种元素以改善可加工性，我们应该考虑到这些元素对已加工零件在使用中的性能和强度的不利影响。例如，当温度升高时，铝会使钢变脆（液体—金属脆化，热脆化，见1.4.3节），尽管其在室温下对力学性能没有影响。
因为硫化铁的构成，硫能严重的减少钢的热加工性，除非有足够的锰来防止这种结构的形成。在室温下，二次磷化钢的机械性能依赖于变形的硫化锰夹杂物的定位（各向异性）。二次磷化钢具有更小的延展性，被单独生成来提高机加工性。
20.9.2 其它不同金属的机加工性
尽管越软的品种易于生成积屑瘤，但铝通常很容易被机加工，导致了很差的表面光洁性。高的切削速度，高的前角和高的后角都被推荐了。有高含量的矽的锻铝合金铸铝合金也许具有磨蚀性，它们要求更硬的刀具材料。尺寸公差控制也许在机加工铝时会成为一个问题，因为它有膨胀的高导热系数和相对低的弹性模数。
铍和铸铁相同。因为它更具磨蚀性和毒性，尽管它要求在可控人工环境下进行机加工。
灰铸铁普遍地可加工，但也有磨蚀性。铸造无中的游离碳化物降低它们的可机加工性，引起刀具切屑或裂口。它需要具有强韧性的工具。具有坚硬的刀具材料的球墨铸铁和韧性铁是可加工的。
钴基合金有磨蚀性且高度加工硬化的。它们要求尖的且具有耐蚀性的刀具材料并且有低的走刀和速度。
尽管铸铜合金很容易机加工，但因为锻铜的积屑瘤形成因而锻铜很难机加工。黄铜很容易机加工，特别是有添加的铅更容易。青铜比黄铜更难机加工。
镁很容易机加工，镁既有很好的表面光洁性和长久的刀具寿命。然而，因为高的氧化速度和火种的危险（这种元素易燃），因此我们应该特别小心使用它。
钳易拉长且加工硬化，因此它生成很差的表面光洁性。尖的刀具是很必要的。
镍基合金加工硬化，具有磨蚀性，且在高温下非常坚硬。它的可机加工性和不锈钢相同。
钽非常的加工硬化，具有可延性且柔软。它生成很差的表面光洁性且刀具磨损非常大。
钛和它的合金导热性(的确，是所有金属中最低的)，因此引起明显的温度升高和积屑瘤。它们是难机加工的。
钨易脆，坚硬，且具有磨蚀性，因此尽管它的性能在高温下能大大提高，但它的机加工性仍很低。
锆有很好的机加工性。然而，因为有爆炸和火种的危险性，它要求有一个冷却性质好的切削液。
20.9.3 各种材料的机加工性
石墨具有磨蚀性。它要求硬的、尖的，具有耐蚀性的刀具。
塑性塑料通常有低的导热性，低的弹性模数和低的软化温度。因此，机加工热塑性塑料要求有正前角的刀具（以此降低切削力），还要求有大的后角，小的切削和走刀深的，相对高的速度和工件的正确支承。刀具应该很尖。
切削区的外部冷却也许很必要，以此来防止切屑变的有黏性且粘在刀具上。有了空气流，汽雾或水溶性油，通常就能实现冷却。在机加工时，残余应力也许
能生成并发展。为了解除这些力，已机加工的部分要在C
C ??16080—（F F ??315175—）的温度范围内冷却一段时间，然而慢慢地无变化地冷却到室温。
热固性塑料易脆，并且在切削时对热梯度很敏感。它的机加工性和热塑性塑料的相同。
因为纤维的存在，加强塑料具有磨蚀性，且很难机加工。纤维的撕裂、拉出和边界分层是非常严重的问题。它们能导致构成要素的承载能力大大下降。而且，这些材料的机加工要求对加工残片仔细切除，以此来避免接触和吸进纤维。
随着纳米陶瓷（见8.2.5节）的发展和适当的参数处理的选择，例如塑性切削（见22.4.2节），陶瓷器的可机加工性已大大地提高了。
金属基复合材料和陶瓷基复合材料很能机加工，它们依赖于单独的成分的特性，比如说增强纤维或金属须和基体材料。
20.9.4 热辅助加工
在室温下很难机加工的金属和合金在高温下能更容易地机加工。在热辅助加工时（高温切削），热源—一个火把，感应线圈，高能束流（例如雷射或电子束），或等离子弧—被集中在切削刀具前的一块区域内。好处是：（a ）低的切削力。（b ）增加的刀具寿命。（c ）便宜的切削刀具材料的使用。（d ）更高的材料切除率。（e ）减少振动。
也许很难在工件内加热和保持一个不变的温度分布。而且，工件的最初微观结构也许被高温影响，且这种影响是相当有害的。尽管实验在进行中，以此来机加工陶瓷器如氮化矽，但高温切削仍大多数应用在高强度金属和高温度合金的车削中。
小结
通常，零件的可机加工性能是根据以下因素来定义的：表面粗糙度，刀具的寿命，切削力和功率的需求以及切屑的控制。材料的可机加工性能不仅取决于起内在特性和微观结构，而且也依赖于工艺参数的适当选择与控制。
红外数据通信技术外文翻译文献(文档含中英文对照即英文原文和中文翻译) Infrared Remote Control System Abstract Red outside data correspondence the technique be currently within the scope of world drive extensive usage of a kind of wireless conjunction technique, drive numerous hardware and software platform support. Red outside the transceiver product have cost low, small scaled turn, the baud rate be quick, point to point SSL, be free from electromagnetism thousand Raos
etc. characteristics, can realization information at dissimilarity of the product fast, convenience, safely exchange and transmission, at short distance wireless deliver aspect to own very obvious of advantage. Along with red outside the data deliver a technique more and more mature, the cost descend, red outside the transceiver necessarily will get at the short distance communication realm more extensive of application. The purpose that design this system is transmit customer’s operation information with infrared rays for transmit media, then demodulate original signal with receive circuit. It use coding chip to modulate signal and use decoding chip to demodulate signal. The coding chip is PT2262 and decoding chip is PT2272. Both chips are made in Taiwan. Main work principle is that we provide to input the information for the PT2262 with coding keyboard. The input information was coded by PT2262 and loading to high frequent load wave whose frequent is 38 kHz, then modulate infrared transmit dioxide and radiate space outside when it attian enough power. The receive circuit receive the signal and demodulate original information. The original signal was decoded by PT2272, so as to drive some circuit to accomplish customer’s operation demand. Keywords: Infrared dray；Code；Decoding；LM386；Red outside transceiver 1 Introduction 1.1 research the background and significance Infrared Data Communication Technology is the world wide use of a wireless connection technology, by the many hardware and software platforms supported. Is a data through electrical pulses and infrared optical pulse switch between the wireless data transceiver technology.
译文资料： 机器人 首先我介绍一下机器人产生的背景，机器人技术的发展，它应该说是一个科学技术发展共同的一个综合性的结果，同时，为社会经济发展产生了一个重大影响的一门科学技术，它的发展归功于在第二次世界大战中各国加强了经济的投入，就加强了本国的经济的发展。另一方面它也是生产力发展的需求的必然结果，也是人类自身发展的必然结果，那么随着人类的发展，人们在不断探讨自然过程中，在认识和改造自然过程中，需要能够解放人的一种奴隶。那么这种奴隶就是代替人们去能够从事复杂和繁重的体力劳动，实现人们对不可达世界的认识和改造，这也是人们在科技发展过程中的一个客观需要。 机器人有三个发展阶段，那么也就是说，我们习惯于把机器人分成三类，一种是第一代机器人，那么也叫示教再现型机器人，它是通过一个计算机，来控制一个多自由度的一个机械，通过示教存储程序和信息，工作时把信息读取出来，然后发出指令，这样的话机器人可以重复的根据人当时示教的结果，再现出这种动作，比方说汽车的点焊机器人，它只要把这个点焊的过程示教完以后，它总是重复这样一种工作，它对于外界的环境没有感知，这个力操作力的大小，这个工件存在不存在，焊的好与坏，它并不知道，那么实际上这种从第一代机器人，也就存在它这种缺陷，因此，在20世纪70年代后期，人们开始研究第二代机器人，叫带感觉的机器人，这种带感觉的机器人是类似人在某种功能的感觉，比如说力觉、触觉、滑觉、视觉、听觉和人进行相类比，有了各种各样的感觉，比方说在机器人抓一个物体的时候，它实际上力的大小能感觉出来，它能够通过视觉，能够去感受和识别它的形状、大小、颜色。抓一个鸡蛋，它能通过一个触觉，知道它的力的大小和滑动的情况。第三代机器人，也是我们机器人学中一个理想的所追求的最高级的阶段，叫智能机器人，那么只要告诉它做什么，不用告诉它怎么去做，它就能完成运动，感知思维和人机通讯的这种功能和机能，那么这个目前的发展还是相对的只是在局部有这种智能的概念和含义，但真正完整意义的这种智能机器人实际上并没有存在，而只是随着我们不断的科学技术的发展，智能的概念越来越丰富，它内涵越来越宽。 下面我简单介绍一下我国机器人发展的基本概况。由于我们国家存在很多其
加工中心数控技术 出处：数控加工中心的分类以及各自特点 出版社:化学工业出版社; 第1版 (2009年3月16日) 作者：徐衡、段晓旭 加工中心是典型的集高技术于一体的机械加工设备，它的发展代表了一个国家设计制造的水平也大大提高了劳动生产率，降低了劳动成本，改善了工人的工作环境，降低了工人的劳动强度。本文经过对不同运动方案和各部件的设计方案的定性分析比较确定该教立式加工中心的进给传动方案为：采用固定床身，电主轴通过安装座安装在床身导轨的滑座上，床身导轨采用滚动导轨，可以实现Y 方向的进给运动。由X-Y双向精密数控工作台带动工件完成X，Y两个方向的进给运动;X，Y，Z三个方向的进给运动均滚珠丝杠，并由交流伺服电机驱动。导轨、滚珠丝杠有相应的润滑、防护等装置。 加工中心（英文缩写为CNC 全称为Computerized Numerical Control）：是带有刀库和自动换刀装置的一种高度自动化的多功能数控机床。在中国香港，台湾及广东一代也有很多人叫它电脑锣。 工件在加工中心上经一次装夹后，数字控制系统能控制机床按不同工序，自动选择和更换刀具，自动改变机床主轴转速、进给量和刀具相对工件的运动轨迹及其他辅助机能，依次完成工件几个面上多工序的加工。并且有多种换刀或选刀功能，从而使生产效率大大提高。 加工中心数控机床是一种装有计算机数字控制系统的机床，数控系统能够处理加工程序，控制机床完成各种动作。与普通机床相比，数控机床能够完成平面曲线和空间曲面的加工，加工精度和生产效率都比较高，因而应用日益广泛。 数控机床的组成 一般来说，数控机床由机械部分、数字控制计算机、伺服系统、PC控制部分、液压气压传动系统、冷却润滑和排泄装置组成。数控机床是由程序控制的，零件的编程工作是数控机床加工的重要组成部分。伺服系统是数控机床的驱动部分，计算机输出的控制命令是通过伺服系统产生坐标移动的。普通的立式加工中心有三个伺服电机，分别驱动纵向工作台、横向工作台、主轴箱沿X向、Y向、Z向运动。X、Y、Z是互相垂直的坐标轴，因而当机床三坐标联动时可以加工空
用于多跳认知无线电网络的分布式网络编码控制信道 Alfred Asterjadhi等著 1 前言 大多数电磁频谱由政府机构长期指定给公司或机构专门用于区域或国家地区。由于这种资源的静态分配，许可频谱的许多部分在许多时间和/或位置未使用或未被充分利用。另一方面，几种最近的无线技术在诸如IEEE802.11，蓝牙，Zigbee之类的非许可频段中运行，并且在一定程度上对WiMAX进行操作;这些技术已经看到这样的成功和扩散，他们正在访问的频谱- 主要是2.4 GHz ISM频段- 已经过度拥挤。为了为这些现有技术提供更多的频谱资源，并且允许替代和创新技术的潜在开发，最近已经提出允许被许可的设备（称为次要用户）访问那些许可的频谱资源，主要用户未被使用或零星地使用。这种方法通常被称为动态频谱接入（DSA），无线电设备发现和机会性利用未使用或未充分利用的频谱带的能力通常称为认知无线电（CR）技术。 DSA和CR最近都引起了无线通信和网络界的极大关注。通常设想两种主要应用。第一个是认知无线接入（CW A），根据该认知接入点，认知接入点负责识别未使用的许可频谱，并使用它来提供对次用户的接入。第二个应用是我们在这个技术中研究的应用，它是认知自组织网络（CAN），也就是使用 用于二级用户本身之间通信的无许可频谱，用于诸如点对点内容分发，环境监控，安全性等目的，灾难恢复情景通信，军事通信等等。 设计CAN系统比CW A有更多困难，主要有两个原因。第一是识别未使用的频谱。在CW A中，接入点的作用是连接到互联网，因此可以使用简单的策略来推断频谱可用性，例如查询频谱调节器在其地理位置的频谱可用性或直接与主用户协商频谱可用性或一些中间频谱经纪人另一方面，在CAN中，与频谱调节器或主要用户的缺乏直接通信需要二级用户能够使用检测技术自己识别未使用的频谱。第二个困难是辅助用户协调媒体访问目的。在CW A中存在接入点和通常所有二级用户直接与之通信（即，网络是单跳）的事实使得直接使用集中式媒体接入控制（MAC）解决方案，如时分多址（TDMA）或正交频分多址（OFDMA）。相反，预计CAN将跨越多跳，缺少集中控制器;而对于传统的单通道多跳自组织网络而言，这个问题的几个解决方案是已知的，因为假设我们处理允许设备访问的具有成
附录A Lathe fixture design and analysis Ma Feiyue (School of Mechanical Engineering, Hefei, Anhui Hefei 230022, China) Abstract: From the start the main types of lathe fixture, fixture on the flower disc and angle iron clamp lathe was introduced, and on the basis of analysis of a lathe fixture design points. Keywords: lathe fixture; design; points Lathe for machining parts on the rotating surface, such as the outer cylinder, inner cylinder and so on. Parts in the processing, the fixture can be installed in the lathe with rotary machine with main primary uranium movement. However, in order to expand the use of lathe, the work piece can also be installed in the lathe of the pallet, tool mounted on the spindle. THE MAIN TYPES OF LATHE FIXTURE Installed on the lathe spindle on the lathe fixture
人工智能的形成及其发展现状分析 冯海东 （长江大学管理学院荆州434023） 摘要：人工智能的历史并不久远，故将从人工智能的出现、形成、发展现 状及前景几个方面对其进行分析，总结其发展过程中所出现的问题，以及发展现状中的不足之处，分析其今后的发展方向。 关键词：人工智能，发展过程，现状分析，前景。 一．引言 人工智能最早是在1936年被英国的科学家图灵提出，并不为多数人所认知。 当时，他编写了一个下象棋的程序，这就是最早期的人工智能的应用。也有著名的“图灵测试”，这也是最初判断是否是人工智能的方案,因此，图灵被尊称为“人工智能之父”。人工智能从产生到发展经历了一个起伏跌宕的过程，直到目前为止，人工智能的应用技术也不是很成熟，而且存在相当的缺陷。 通过搜集的资料，将详细的介绍人工智能这个领域的具体情况，剖析其面临的挑战和未来的前景。 二．人工智能的发展历程 1. 1956年前的孕育期 (1) 从公元前伟大的哲学家亚里斯多德(Aristotle)到16世纪英国哲学家培根(F. Bacon)，他们提出的形式逻辑的三段论、归纳法以及“知识就是力量”的警句，都对人类思维过程的研究产生了重要影响。 （2）17世纪德国数学家莱布尼兹(G..Leibniz)提出了万能符号和推理计算思想，为数理逻辑的产生和发展奠定了基础，播下了现代机器思维设计思想的种子。而19世纪的英国逻辑学家布尔（G. Boole）创立的布尔代数，实现了用符号语言描述人类思维活动的基本推理法则。 （3） 20世纪30年代迅速发展的数学逻辑和关于计算的新思想，使人们在计算机出现之前，就建立了计算与智能关系的概念。被誉为人工智能之父的英国天才的数学家图灵（A. Tur-ing）在1936年提出了一种理想计算机的数学模型，即图灵机之后,1946年就由美国数学家莫克利（J. Mauchly）和埃柯特（J. Echert）研制出了世界上第一台数字计算机，它为人工智能的研究奠定了不可缺少的物质基础。1950年图灵又发表了“计算机与智能”的论文，提出了著名的“图灵测试”，形象地指出什么是人工智能以及机器具有智能的标准，对人工智能的发展产生了极其深远的影响。 （4） 1934年美国神经生理学家麦克洛奇(W. McCulloch) 和匹兹(W. Pitts )建立了第一个神经网络模型，为以后的人工神经网络研究奠定了基础。 2. 1956年至1969年的诞生发育期 (1)1956年夏季，麻省理工学院（MIT)的麦卡锡（J．McCarthy）、明斯基（M. Minshy）、塞尔夫里奇（O. Selfridge)与索罗门夫(R. Solomonff)、 IBM的洛
Lathes Lathes are machine tools designed primarily to do turning, facing and boring, Very little turning is done on other types of machine tools, and none can do it with equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the work piece. Consequently, more lathes of various types are used in manufacturing than any other machine tool. The essential components of a lathe are the bed, headstock assembly, tailstock assembly, and the leads crew and feed rod. The bed is the backbone of a lathe. It usually is made of well normalized or aged gray or nodular cast iron and provides s heavy, rigid frame on which all the other basic components are mounted. Two sets of parallel, longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets, They are precision-machined to assure accuracy of alignment. On most modern lathes the way are surface-hardened to resist wear and abrasion, but precaution should be taken in operating a lathe to assure that the ways are not damaged. Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed. The headstock is mounted in a foxed position on the inner ways, usually at the left end of the bed. It provides a powered means of rotating the word at various speeds . Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission—through which the spindle can be rotated at a number of speeds. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical drives. Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through which long bar stock can be fed. The size of maximum size of bar stock that can be machined when the material must be fed through spindle. The tailsticd assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location, An upper casting fits on the lower one and can be moved transversely upon it, on some type of keyed ways, to permit aligning the assembly is the tailstock quill. This is a hollow steel cylinder, usually about 51 to 76mm(2to 3 inches) in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a hand wheel and screw. The size of a lathe is designated by two dimensions. The first is known as the swing. This is the maximum diameter of work that can be rotated on a lathe. It is approximately twice the distance between the line connecting the lathe centers and the nearest point on the ways, The second size dimension is the maximum distance between centers. The swing thus indicates the maximum work piece diameter that can be turned in the lathe, while the distance between centers indicates the maximum length of work piece that can be mounted between centers. Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power drive for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm(12 to 24 inches)swing and from 610 to 1219 mm(24 to 48 inches) center distances, but swings up to 1270 mm(50 inches) and center distances up
5G无线通信网络中英文对照外文翻译文献(文档含英文原文和中文翻译)
翻译： 5G无线通信网络的蜂窝结构和关键技术 摘要 第四代无线通信系统已经或者即将在许多国家部署。然而，随着无线移动设备和服务的激增，仍然有一些挑战尤其是4G所不能容纳的，例如像频谱危机和高能量消耗。无线系统设计师们面临着满足新型无线应用对高数据速率和机动性要求的持续性增长的需求，因此他们已经开始研究被期望于2020年后就能部署的第五代无线系统。在这篇文章里面，我们提出一个有内门和外门情景之分的潜在的蜂窝结构，并且讨论了多种可行性关于5G无线通信系统的技术，比如大量的MIMO技术，节能通信，认知的广播网络和可见光通信。面临潜在技术的未知挑战也被讨论了。 介绍 信息通信技术（ICT）创新合理的使用对世界经济的提高变得越来越重要。无线通信网络在全球ICT战略中也许是最挑剔的元素，并且支撑着很多其他的行业，它是世界上成长最快最有活力的行业之一。欧洲移动天文台（EMO）报道2010年移动通信业总计税收1740亿欧元,从而超过了航空航天业和制药业。无线技术的发展大大提高了人们在商业运作和社交功能方面通信和生活的能力无线移动通信的显著成就表现在技术创新的快速步伐。从1991年二代移动通信系统(2G)的初次登场到2001年三代系统（3G）的首次起飞，无线移动网络已经实现了从一个纯粹的技术系统到一个能承载大量多媒体内容网络的转变。4G无线系统被设计出来用来满足IMT-A技术使用IP面向所有服务的需求。在4G系统中，先进的无线接口被用于正交频分复用技术（OFDM），多输入多输出系统（MIMO）和链路自适应技术。4G无线网络可支持数据速率可达1Gb/s的低流度，比如流动局域无线访问，还有速率高达100M/s的高流速，例如像移动访问。LTE系统和它的延伸系统LTE-A，作为实用的4G系统已经在全球于最近期或不久的将来部署。 然而，每年仍然有戏剧性增长数量的用户支持移动宽频带系统。越来越多的
毕业设计 外文翻译 题目曲轴的加工工艺及夹具设计学院航海学院 专业轮机工程 学生佟宝诚 学号 10960123 指导教师彭中波 重庆交通大学 2014年
Proceedings of IMECE2008 2008 ASME International Mechanical Engineering Congress and Exposition October 31-November 6, 2008, Boston, Massachusetts, USA IMECE2008-67447 MULTI-OBJECTIVE SYSTEM OPTIMIZATION OF ENGINE CRANKSHAFTS USING AN INTEGRATION APPROACH Albert Albers/IPEK Institute of Product Development University of Karlsruhe Germany Noel Leon/CIDyT Center for Innovation andDesign Monterrey Institute of Technology,Mexico Humberto Aguayo/CIDyT Center forInnovation and Design, Monterrey Institute ofTechnology, Mexico Thomas Maier/IPEK Institute of Product Development University of Karlsruhe Germany ABSTRACT The ever increasing computer capabilities allow faster analysis in the field of Computer Aided Design and Engineering (CAD & CAE). CAD and CAE systems are currently used in Parametric and Structural Optimization to find optimal topologies and shapes of given parts under certain conditions. This paper describes a general strategy to optimize the balance of a crankshaft, using CAD and CAE software integrated with Genetic Algorithms (GAs) via programming in Java. An introduction to the groundings of this strategy is made among different tools used for its implementation. The analyzed crankshaft is modeled in commercial parametric 3D CAD software. CAD is used for evaluating the fitness function (the balance) and to make geometric modifications. CAE is used for evaluating dynamic restrictions (the eigenfrequencies). A Java interface is programmed to link the CAD model to the CAE software and to the genetic algorithms. In order to make geometry modifications to
人工智能 【摘要】：人工智能是一门极富挑战性的科学，但也是一门边沿学科。它属于自然科学和社会科学的交叉。涉及的学科主要有哲学、认知科学、数学、神经生理学、心理学、计算机科学、信息论、控制论、不定性论、仿生学等。人工智能(Artificial Intelligence)，英文缩写为AI。它是研究、开发用于模拟、延伸和扩展人的智能的理论、方法、技术及应用系统的一门新的技术科学。人工智能是计算机科学的一个分支，它企图了解智能的实质，并生产出一种新的能以人类智能相似的方式做出反应的智能机器，该领域的研究包括机器人、语言识别、图像识别、自然语言处理和专家系统等1。 【关键词】：人工智能；应用领域；发展方向；人工检索。 1．人工智能描述 人工智能(Artificial Intelligence) ，英文缩写为AI。它是研究、开发用于模拟、延伸和扩展人的智能的理论、方法、技术及应用系统的一门新的技术科学2。人工智能是计 算机科学的一个分支，它企图了解智 能的实质，并生产出一种新的能以人 类智能相似的方式作出反应的智能 机器，该领域的研究包括机器人、语 言识别、图像识别、自然语言处理和 专家系统等。“人工智能”一词最初 是在1956 年Dartmouth学会上提出 的。从那以后,研究者们发展了众多 理论和原理,人工智能的概念也随之扩展。人工智能是一门极富挑战性的科学，从事这项工作的人必须懂得计算机知识，心理学和哲学。人工智能是包括十分广泛的科学，它由不同的领域组成，如机器学习，计算机视觉等等，总的说来，人工智能研究的一个主要目标是使机器能够胜任一些通常需要人类智能才能完成的复杂工作。但不同的时代、不同的人对这种“复杂工作”的理解是不同的。例如繁重的科学和工程计算本来是要人脑来承担的，现在计算机不但能完成这种计算, 而且能够比人脑做得更快、更准确，因之当代人已不再把这种计算看作是“需要人类智能才能完成的复 1.蔡自兴，徐光祐.人工智能及其应用.北京：清华大学出版社，2010 2元慧·议当人工智能的应用领域与发展状态〖Ｊ〗．2008
英文文献 Numerical control laser processing technology and application Pick to: as the main symbol of science and Technology development in the 20th century and the modern information society one of the pillars of optoelectronic Technology, Laser Technology, Laser Technology) and the development of Laser industry attaches great importance to by the advanced countries in the world. Numerical control and integrated the Laser and the optical system of the computer numerical control technology, advanced and high precision and automation of the workpiece positioning, the combination of formation, development and production of machining center has become a Laser machining, Laser Processing) is an important trend of development. Key words: CNC; Laser machining, Laser Processing); Level; application Before: laser is regarded as one of the most important scientific discoveries of the twentieth century, as soon as it was caused the great attention of materials scientists. In November 1971, gm pioneered the use of a 250 w CO2 laser to improve wear resistance materials using laser radiation test and research, and in 1974 successfully completed automobile redirector shell
中英文翻译 附件1：外文资料翻译译文 通用移动通信系统的回顾 1.1 UMTS网络架构 欧洲/日本的3G标准，被称为UMTS。 UMTS是一个在IMT-2000保护伞下的ITU-T 批准的许多标准之一。随着美国的CDMA2000标准的发展，它是目前占主导地位的标准，特别是运营商将cdmaOne部署为他们的2G技术。在写这本书时，日本是在3G 网络部署方面最先进的。三名现任运营商已经实施了三个不同的技术：J - PHONE 使用UMTS，KDDI拥有CDMA2000网络，最大的运营商NTT DoCoMo正在使用品牌的FOMA（自由多媒体接入）系统。 FOMA是基于原来的UMTS协议，而且更加的协调和标准化。 UMTS标准被定义为一个通过通用分组无线系统（GPRS）和全球演进的增强数据
技术（EDGE）从第二代GSM标准到UNTS的迁移，如图。这是一个广泛应用的基本原理，因为自2003年4月起，全球有超过847万GSM用户，占全球的移动用户数字的68％。重点是在保持尽可能多的GSM网络与新系统的操作。 我们现在在第三代（3G）的发展道路上，其中网络将支持所有类型的流量：语音，视频和数据，我们应该看到一个最终的爆炸在移动设备上的可用服务。此驱动技术是IP协议。现在，许多移动运营商在简称为2.5G的位置，伴随GPRS的部署，即将IP骨干网引入到移动核心网。在下图中，图2显示了一个在GPRS网络中的关键部件的概述，以及它是如何适应现有的GSM基础设施。 SGSN和GGSN之间的接口被称为Gn接口和使用GPRS隧道协议（GTP的，稍后讨论）。引进这种基础设施的首要原因是提供连接到外部分组网络如，Internet或企业Intranet。这使IP协议作为SGSN和GGSN之间的运输工具应用到网络。这使得数据服务，如移动设备上的电子邮件或浏览网页，用户被起诉基于数据流量，而不是时间连接基础上的数据量。3G网络和服务交付的主要标准是通用移动通信系统，或UMTS。首次部署的UMTS是发行'99架构，在下面的图3所示。 在这个网络中，主要的变化是在无线接入网络（RAN的）CDMA空中接口技术的引进，和在传输部分异步传输模式作为一种传输方式。这些变化已经引入，主要是为了支持在同一网络上的语音，视频和数据服务的运输。核心网络保持相对不变，主要是软件升级。然而，随着目前无线网络控制器使用IP与3G的GPRS业务支持节点进行通信，IP协议进一步应用到网络。 未来的进化步骤是第4版架构，如图4。在这里，GSM的核心被以语音IP技术为基础的IP网络基础设施取代。 海安的发展分为两个独立部分：媒体网关（MGW）和MSC服务器（MSS）的。这基本上是打破外连接的作用和连接控制。一个MSS可以处理多个MGW，使网络更具有扩展性。 因为现在有一些在3G网络的IP云，合并这些到一个IP或IP/ ATM骨干网是很有意义的（它很可能会提供两种选择运营商）。这使IP权利拓展到整个网络，一直到BTS(基站收发信台)。这被称为全IP网络，或推出五架构，如图五所示。在HLR/ VLR/VLR/EIR被推广和称为HLR的子系统（HSS）。 现在传统的电信交换的最后残余被删除，留下完全基于IP协议的网络运营，并
2604130359 CNC Cutting Technology Review Numerical control high speed cutting technology (High Speed Machining, HSM, or High Speed Cutting, HSC), is one of the advanced manufacturing technology to improve the machining efficiency and quality, the study of related technology has become an important research direction of advanced manufacturing technology at home and abroad. China is a big manufacturing country, in the world of industry transfer to accept the front instead of back-end of the transfer, to master the core technology of advanced manufacturing, or in a new round of international industrial structure adjustment, our country manufacturing industry will further behind. Imminent research on the theory and application of advanced technology. 1, high-speed CNC machining meaning High speed cutting theory put forward by the German physicist Carl.J.Salomon in the last century and early thirty's. He concluded by a lot of experiments: in the normal range of cutting speed, cutting speed if the increase, will cause the cutting temperature rise, exacerbating the wear of cutting tool; however, when the cutting speed is increased to a certain value, as long as more than the inflection point, with the increase of the cutting speed, cutting temperature can not rise, but will decline, so as long as the cutting speed is high enough, it can be solved very well in high cutting temperature caused by tool wear is not conducive to the cutting problem, obtained good processing efficiency. With the development of manufacturing industry, this theory is gradually paid more attention to, and attracted a lot of attention, on the basis of this theory has gradually formed the field of high-speed cutting technology of NC, relatively early research on NC High-speed Machining Technology in developed countries, through the theoretical basis of the research, basic research and applied research and development application, at present applications have entered the substantive stage in some areas. The high-speed cutting processing category, generally have the following several kinds of classification methods, one is to see that cutting speed, cutting speed over conventional cutting speed is 5-10 times of high speed cutting. Also has the scholar to spindle speed as the definition of high-speed processing standards, that the spindle speed is higher than that of 8000r\/min for high speed machining. And from the machine tool spindle design point of view, with the product of DN diameter of spindle and spindle speed, if the value of DN to (5~2000) * 105mm.r\/min, is considered to be of high speed machining. In practice, different processing methods, different materials, high speed cutting speed corresponding to different. Is generally believed that the turning speed of (700~7000) m\/min, milling speed reaches m\/min (300~6000), that is in the high-speed cutting. In addition, from the practical considerations, high-speed machining concept not only contains the high speed cutting process, integration and optimization also contains the process of cutting, is a