单片机交通灯
中英文资料对照外文翻译文献
原文
题目：DESIGN OF TRAFFIC LIGHT BASED ON MCU
Because of the rapid development of our economy resulting in the car number of large and medium-sized cities surged and the urban traffic, is facing serious test, leading to the traffic problem increasingly serious, its basically are behaved as follows: traffic accident frequency, to the human life safety enormous threat, Traffic congestion, resulting in serious travel time increases, energy consumption increase; Air pollution and noise pollution degree of deepening, etc. Daily traffic jams become people commonplace and had to endure. In this context, in combination with the actual situation of urban road traffic, develop truly suitable for our own characteristics of intelligent signal control system has become the main task.
Preface
In practical application at home and abroad, according to the actual traffic signal control application inspection, planar independent intersection signal control basic using set cycle, much time set cycle, half induction, whole sensor etc in several ways. The former two control mode is completely based on planar intersection always traffic flow data of statistical investigation, due to traffic flow the existence of variable sex and randomicity, the two methods have traffic efficiency is low, the scheme, the defects of aging and half inductive and all the inductive the two methods are in the former two ways based on increased vehicle detector and according to the information provided to adjust cycle is long and green letter of vehicle, it than random arrived adaptability bigger, can make vehicles in the parking cord before as few parking, achieve traffic flowing effect
In modern industrial production,current,voltage,temperature, pressure, and flow rate, velocity, and switch quantity are common mainly controlled parameter. For example: in metallurgical industry, chemical production, power engineering, the papermaking industry, machinery and food processing and so on many domains, people need to transport the orderly
control. By single chip microcomputer to control of traffic, not only has the convenient control, configuration simple and flexible wait for an advantage, but also can greatly improve the technical index by control quantity, thus greatly improve product quality and quantity. Therefore, the monolithic integrated circuit to the traffic light control problem is an industrial production we often encounter problems.
In the course of industrial production, there are many industries have lots of traffic equipment, in the current system, most of the traffic control signal is accomplished by relays, but relays response time is long, sensitivity low, long-term after use, fault opportunity increases greatly, and adopts single-chip microcomputer control, the accuracy of far greater than relays, short response time, software reliability, not because working time reduced its performance sake, compared with, this solution has the high feasibility.
About AT89C51
1.function characteristics description:
AT89C51 is a low power consumption, high performance CMOS8 bit micro-controller, has the 8K in system programmable Flash memory. Use high-density Atmel company the beltpassword nonvolatile storage technology and manufacturing, and industrial 80S51 product instructions and pin fully compatible. Chip Flash allow program memory in system programmable, also suitable for conventional programmer. In a single chip, have dexterous 8 bits CPU and in system programmable Flash, make AT89C51 for many embedded control application system provides the high flexible, super efficient solution. AT89C51 has the following standard function: 8k bytes Flash, 256 bytes RAM, 32-bit I/O mouth line, the watchdog timer, two data pointer, three 16 timer/counter, a 6 vector level 2 interrupt structure, full-duplex serial port, piece inside crystals timely clock circuit. In addition, AT89C51 can drop to 0Hz static logic operation, support two software can choose power saving mode. Idle mode, the CPU to stop working, allowing the RAM, timer/counter, serial ports, interruption continue to work. Power lost protection mode, RAM content being saved, has been frozen, microcontroller all work stop, until the next interruption or hardware reset so far. As shown in figure 1 for the AT89C51 pins allotment.
Figure 1 the AT89C51 pins allotment
2.interrupt introduction
AT89C51 has six interrupt sources: two external interruption, (and), three timer interrupt (timer 0, 1, 2) and a serial interrupts. Each interrupt source can be passed buy bits or remove IE the relevant special register interrupt allow control bit respectively make effective or invalid interrupt source. IE also includes an interrupt allow total control bit EA, it can be a ban all interrupts. IE. Six is not available. For AT89C51, IE. 5 bits are also not be used. User software should not give these bits write 1. They AT89 series for new product reserved. Timer 2 can be TF2 and the T2CON registers EXF2 or logical triggered. Program into an interrupt service, the sign bit can be improved by hardware qing 0. In fact, the interrupt service routine must determine whether TF2 or EXF2 activation disruption, the sign bit must also by software qing 0. Timer 0 and 1 mark a timer TF0 and TF1 has been presented in the cycle count overflow S5P2 074 bits. Their value until the next cycle was circuit capture down. However, the timer 2 marks a TF2 in count overflow of the cycle of S2P2 074 bits, in the same cycle was circuit capture down
3.external clock driving characteristics
Table 1
4.leisure and power lost pattern external pins state
Table 2
About 8255 chip
1.8255 features:
(1)A parallel input/output LSI chips, efficacy of I/O devices, but as CPU bus and peripheral interface.
(2)It has 24 programmable Settings of I/O mouth, even three groups of 8 bits I/O mouth to mouth, PB mouth and PA PC mouth. They are divided into two groups 12 I/O mouth, A group including port A and C mouth (high four, PC4 ~ PC7), including group B and C port B mouth (low four, PC0 ~ PC3). A group can be set to give basic I/O mouth, flash control (STROBE) I/O flash controlled, two-way I/O3 modes, Group B can only set to basic I/O or flash controlled the I/O, and these two modes of operation mode entirely by controlling registers control word decision.
2. 8255 pins efficacy:
(1). RESET: RESET input lines, when the input outside at high levels, all internal registers (including control registers) were removed, all I/O ports are denoting input methods.
(2). CS: chip choose a standard lamp line 1, when the input pins for low levels, namely/CS = 0, said chip is selected, allow 8255 and CPU for communications, / CS = 1, 8255 cannot with CPU do data transmission.
(3). RD: read a standard lamp line 1, when the input pins for low levels, namely/RD = 0 and/CS = 0, allow 8255 through the data bus to the CPU to send data or state information, namely the CPU 8255 read from the information or data.
(4). The WR: write a standard lights, when the input pins for low levels, namely/WR = 0 and/CS = 0, allows the CPU will data or control word write 8255.
(5). D7: three states D0 ~ two-way data bus, 8255 and CPU data transmission channel, when the CPU execution input/output instruction, through its realization 8 bits of data read/write operation, control characters and status information transmitted through the data bus.
(6). PA0 ~ PA7: port A input and output lines, A 8 bits of data output latches/buffers, an 8 bits of data input latches.
(7). PB0 ~ PB7: port B input and output lines, a 8 bits of I/O latches, an 8 bits of input and output buffer.
(8). PC0 ~ PC7: port C input and output lines, a 8 bits of data output latches/buffers, an 8 bits of data input buffer. Port C can through the way of working setting into two four ports, every 4 digit port contains A 4 digit latches, respectively with the port A and port B cooperate to use, can be used as control standard lights output or state standard lights input ports.
(9). A0, A1: address selection line, used to select the PA 8255 mouth, PB mouth, PC mouth and controlling registers.
When A0=0, A1= 0, PA mouth be chosen;
When A0=0, A1 = 1, PB mouth be chosen;
When A0=0, A1 = 1, PC mouth be chosen;
When A0=1, A1= 1, control register is selected.
Concerning seven section LED display introduction
Through light emitting diode chip appropriate link (including series and parallel) and
appropriate optical structure. May constitute a luminous display light-emitting segments or shine points. By these luminous segments or shine point can be composed digital tube, symbols tube, m word pipe, tube, multilevel matrix display tube etc. Usually the digital tube, symbols tube, m word tube were called stroke display, but the stroke displays and matrix tube collectively referred to as character displays.
1. The LED display classification
(1) by word high marks: stroke monitors word high least 1mm (monolithic integrated type more digital tube word high in commonly 2 ~ 3mm). Other types of stroke display tiptop
1.27 mm (0.5 inch) even up to hundreds of mm.
(2) color-coded score red, orange, yellow, green and several kinds.
(3) according to the structure points, reflecting cover type, a single point-elastic and monolithic integrated type.
(4) from the luminous section electrode connection mode of points of anode and cathode two kinds.
2. LED display parameters
Due to the LED display is LED based, so its light, and the electrical characteristics and ultimate meaning of the parameters with most of the same light emitting diode. But because the LED monitor containing multiple light emitting diode, it must has the following specific parameters:
(1) the luminous intensity ratio
Due to the digital tube paragraphs in the same driving voltage, each are not identical, so positive current each different. The luminous intensity All segments of the luminous intensity values the ratio of the maximum and minimum values for the luminous intensity ratio. The ratio between 2.3 in 1.5 ~, the maximum cannot exceed 2.5.
(2) pulse positive current
IF each segment of typical strokes displays for positive dc working current IF, then the pulse, positive current can be far outweigh.someotherwordpeopledontthinkoffirst. Pulse 390v smaller, pulse positive current can be bigger.
Traffic signal control type
The purpose of the traffic signal control are three: first,in time and space space intersection traffic in different directions,control traffic operation order; Second, make on
planar cross the road network on the people and objects of transport at the highest efficiency, Third, as the road users to provide necessary information, and help them to effectively use the traffic facilities. Road traffic signal control of basic types have many points method.
According to the control geometry characteristic is divided into: single intersection control - point control, the traffic trunk lines of coordinated control - wire, traffic network coordination control surface controlling; -- According to the control principle differentiates: timing control, induced control and adaptive control.
About watch-dog circuit
By single-chip computers.the micro computer system, because of single chip work often can be affected by external electromagnetic interference, causing program run fly while into dead circulation, the program's normal operation be interrupted by single chip microcomputer control system was unable to work, can cause the whole system of come to a standstill, happen unpredictable consequences, so out of microcontroller running status real-time.according consideration, they generate a specially used for monitoring microcontroller program running state of the chip, commonly known as "watchdog" (watchdog).
MAX692 was slightly system monitoring circuit chip, have back-up battery switching, power lost discriminant functions monitoring, the watchdog. The encapsulation and pin instructions as figure2shows.
Figure 2 MAX692 encapsulation and pins
Watch-dog circuit application, make SCM can in no condition to achieve continuous work, its working principle is: the watchdog chip and MCU an I/O pins are linked together, the I/O pins through program control it regularly to the watchdog of the pins on into high level (or the low level), this program statement is scattered on SCM other control statements,
once among single-chip due to the interference makes application run into a fly after the procedures section into dead circulation state, write the watchdog pins program cannot be executed, this time, the watch-dog circuit will be without microcontroller sent signals, then at it and MCU reset pin connected pin reset signal give out a a, make SCM reposition occurs, namely the program from program memory splittext started, so we realized the MCU automatic reset.
Infrared detection circuit
The infrared radiation photon in semiconductor materials stimutes the non-equilibrium carriers (electronic or holes), cause electrical properties change. Because carrier does not escape in vitro, so called within the photoelectric effect. Quantum photoelectric effect high sensitivity, response speed heat detectors much faster, is optional detectors. In order to achieve the best performance, generally need worked in low temperature. Photoelectric detector can be divided into:
(1) optical type: also called photoconductive resistance. The incident photon stimulate the valence band uniform semiconductor electronic across forbidden band into the conduction band and left in valence band, cause cavitation increases, for electric conductance eigen light conductivity. From the band gaps of impurity level also can stimulate light into the conduction band or born carriers valence band, and for impurities light conductivity. The cutoff wavelength by impurity ionization energy (ie) decision. Quantum efficiencies below eigen optical and require lower working temperature.
(2) photovoltaic type: mainly p - n knot of light born volts effect. Energy more than the width of infrared photonic band gaps in "area and its nearby of electrons cavitation. Existing "electric field make hole into p area, electronic into n area, two parts appear potentials. Deoxidization device have voltage or current signal. Compared with optical detectors, pv detector detect rate more than forty percent of figure limit, Don't require additional bias electric field and load resistance, no power consumption, having a high impedance. These characteristics of preparation and use of the focal plane array bring great benefits.
(3) light emitting - Schottky potential barrier detector: metal and semiconductor contact, typically include PtSi/Si structure and form was Schott potential barrier, infrared photon through Si layer for PtSi absorption, electronic Fermi level, obtain energy leap over left cavitation potential barrier into the Si substrate, PtSi layer of electronic was collected,
complete infrared detection. Make full use of Si integration technology, facilitate production, with lower cost and good uniformity wait for an advantage, but make it mass (1024 x 1024 even greater) focal plane array to make up for the defect of quantum low efficiency. Have strict low temperature requirements. With this kind of detector, both at home and abroad has already produced as qualitative good thermography. Pt Si/Si structure made of FPA is the earliest IRFPA.
Timing counting and traffic calculation
Using MCS - 51 internal timer/counter for timing, cooperate software delay realizes the timer. This method hardware cost saving, cut allows the reader in timer/counter use, disruptions and programming get exercise and improve. Computation formula is as follows: TC = M - C
Type in, M for counter touch value, the value and the counter working way concerned.
For a traffic intersection, it can in the shortest possible time to achieve maximum traffic, even reached the best performance, we call in unit of time to achieve the maximum flow multi-energy for cars.
Use the equation: (traffic = traffic/time) to represent.
译文
题目：基于单片机的交通灯设计
我国经济快速发展，汽车数量猛增，大中型城市的城市交通正面临着严峻的考验，交通问题日益严重，其主要表现如下：交通事故频发，对人类生命安全造成极大威胁；交通拥堵严重，导致出行时间增加，能源消耗加大；空气污染和噪声污染程度日益加深等。日常的交通堵塞成为人们司空见惯而又不得不忍受的问题。在这种背景下，结合我国城市道路交通的实际情况，开发出真正适合我们自身特点的智能信号灯控制系统已经成为当前的主要任务。
前言
在实际应用上，根据对国内外实际交通信号控制应用的考察，平面独立交叉口信号控制基本采用定周期、多时段定周期、半感应、全感应等几种方式。前两种控制方式完全是基于对平面交叉口既往交通流数据的统计调查，由于交通流存在的变化性和随机性，这两种方式都具有通行效率低、方案易老化的缺陷，而半感应式和全感应式这两种方式是在前两种方式的基础上增加了车辆检测器并根据其提供的信息来调整周期长和绿信比，它对车辆随机到达的适应性较大，可使车辆在停车线前尽可能少停车，达到交通流畅的效果。
在现代化的工业生产中，电流、电压、温度、压力、流量、流速和开关量都是常用的主要被控参数。例如：在冶金工业、化工生产、电力工程、造纸行业、机械制造和食品加工等诸多领域中，人们都需要对交通进行有序的控制。采用单片机来对交通进行控制，不仅具有控制方便、组态简单和灵活性大等优点，而且可以大幅度提高被控制量的技术指标，从而能够大大提高产品的质量和数量。因此，单片机对交通灯的控制问题是一个工业生产中经常会遇到的问题。
在工业生产中，有很多行业有大量的交通灯设备，在现行系统中,大多数的交通控制信号都是用继电器来完成的,但继电器响应时间长,灵敏度低,长期使用之后,故障机会大大增加,而采用单片机控制,其精度远远大于继电器,响应时间短,软件可靠性高,不会因为工作时间缘故而降低其性能,相比而言,本方案具有很高的可行性。
关于AT89C51
1.功能特征描述:
AT89C51是一种低功耗、高性能CMOS8位微控制器，具有8K 在系统可编程Flash 存储器。使用Atmel 公司高密度非易失性存储器技术制造，与工业80S51 产品指令和引脚完全兼容。片上Flash允许程序存储器在系统可编程，亦适于常规编程器。在单芯片上，拥有灵巧的8 位CPU 和在系统可编程Flash，使得AT89C51为众多嵌入式控制应用系统提供高灵活、超有效的解决方案。AT89C51具有以下标准功能： 8k字节Flash，256字节RAM，32 位I/O 口线，看门狗定时器，2 个数据指针，三个16 位定时器/计数器，一个6向量2级中断结构，全双工串行口，片内晶振及时钟电路。另外，AT89C51 可降至0Hz 静态逻辑操作，支持2种软件可选择节电模式。空闲模式下，CPU停止工作，允许RAM、定时器/计数器、串口、中断继续工作。掉电保护方式下，RAM内容被保存，振荡器被冻结，单片机一切工作停止，直到下一个中断或硬件复位为止。如图1为8051引脚分配图。
图-1 8051引脚分配图
2.中断介绍
AT89C51有6个中断源：两个外部中断（INT0和INT1），三个定时中断（定时器0、1、2）和一个串行中断。每个中断源都可以通过置位或清除特殊寄存器IE 中的相关中断允许控制位分别使得中断源有效或无效。IE还包括一个中断允许总控制位EA，它能一次禁止所有中断。IE.6位是不可用的。对于AT89C51，IE.5位也是不能用的。用户软件不应给这些位写1。它们为AT89系列新产品预留。定时器2可以被寄存器T2CON 中的TF2和EXF2的或逻辑触发。程序进入中断服务后，这些标志位都可以由硬件清0。实际上，中断服务程序必须判定是否是TF2 或EXF2激活中断，标志位也必须由软件清0。定时器0和定时器1标志位TF0 和TF1在计数溢出的那个周期的S5P2被置位。它们
的值一直到下一个周期被电路捕捉下来。然而，定时器2的标志位TF2 在计数溢出的那个周期的S2P2被置位，在同一个周期被电路捕捉下来。
3.外部时钟驱动特性
表2
关于8255芯片
1.8255特性：
(1) 一个并行输入/输出的LSI芯片,多功效的I/O器件,可作为CPU总线与外围的接口.
(2) 具有24个可编程设置的I/O口,即使3组8位的I/O口为PA口,PB口和PC口.它们又可分为两组12位的I/O口,A组包括A口及C口(高4位,PC4~PC7),B组包括B口及C口(低4位,PC0~PC3).A组可设置为基本的I/O口,闪控(STROBE)的I/O闪控式,双向I/O3种模式；B组只能设置为基本I/O或闪控式I/O两种模式,而这些操作模式完全由控制寄存器的控制字决定.
2.8255引脚功效：
(1).RESET：复位输入线，当该输入端外于高电平时，所有内部寄存器(包括控制寄存器)均被清除，所有I/O口均被置成输入方式。
(2).CS：芯片选择旌旗灯号线，当这个输入引脚为低电平时,即/CS=0时,表示芯片被选中，允许8255与CPU进行通讯；/CS=1时,8255无法与CPU做数据传输。
(3).RD：读旌旗灯号线，当这个输入引脚为低电平时,即/RD=0且/CS=0时,允许8255通过数据总线向CPU发送数据或状态信息，即CPU从8255读取信息或数据。
(4).WR：写入旌旗灯号，当这个输入引脚为低电平时,即/WR=0且/CS=0时,允许CPU 将数据或控制字写入8255。
(5).D0~D7：三态双向数据总线，8255与CPU数据传送的通道，当CPU执行输入输出指令时，通过它实现8位数据的读/写操作，控制字和状态信息也通过数据总线传送。
(6).PA0~PA7：端口A输入输出线，一个8位的数据输出锁存器/缓冲器，一个8位的数据输入锁存器。
(7).PB0~PB7：端口B输入输出线，一个8位的I/O锁存器，一个8位的输入输出缓冲器。
(8).PC0~PC7：端口C输入输出线，一个8位的数据输出锁存器/缓冲器，一个8位的数据输入缓冲器。端口C可以通过工作方式设定而分成2个4位的端口，每个4位的端口包含一个4位的锁存器，分别与端口A和端口B配合使用，可作为控制旌旗灯号输出或状态旌旗灯号输入端口。
(9).A0,A1：地址选择线,用来选择8255的PA口,PB口,PC口和控制寄存器。
当A0=0,A1=0时,PA口被选择；
当A0=0,A1=1时,PB口被选择；
当A0=1,A1=0时,PC口被选择；
当A0=1,A1=1时,控制寄存器被选择。
有关七段LED显示器的介绍
通过发光二极管芯片的适当连接（包括串联和并联）和适当的光学结构。可构成发光显示器的发光段或发光点。由这些发光段或发光点可以组成数码管、符号管、米字管、矩阵管、电平显示器管等等。通常把数码管、符号管、米字管共称笔画显示器，而把笔画显示器和矩阵管统称为字符显示器。
1.LED显示器分类
（1）按字高分：笔画显示器字高最小有1mm（单片集成式多位数码管字高一般在2～3mm）。其他类型笔画显示器最高可达12.7mm（0.5英寸）甚至达数百mm。
（2）按颜色分有红、橙、黄、绿等数种。
（3）按结构分，有反射罩式、单条七段式及单片集成式。
（4）从各发光段电极连接方式分有共阳极和共阴极两种。
2.LED显示器的参数
由于LED显示器是以LED为基础的，所以它的光、电特性及极限参数意义大部分与发光二极管的相同。但由于LED显示器内含多个发光二极管，所以需有如下特殊参数：
(1) 发光强度比
由于数码管各段在同样的驱动电压时，各段正向电流不相同，所以各段发光强度不同。所有段的发光强度值中最大值与最小值之比为发光强度比。比值可以在 1.5～2.3间，最大不能超过2.5。
(2) 脉冲正向电流
若笔画显示器每段典型正向直流工作电流为IF，则在脉冲下，正向电流可以远大于IF。脉冲占空比越小，脉冲正向电流可以越大。
交通信号控制类型
交通信号控制的目的有三点：第一，在时间上和空间上分隔交叉口不同方向的车流，控制车流的运行秩序；第二，使在平面交叉的道路网络上人和物的运输达到最高效率；第三，为道路使用者提供必要的信息，帮助他们有效地使用交通设施。道路交通信号控制的基本类型有多种分法。
按控制区几何特性划分为：单个交叉口的控制——点控、交通干线的协调控制——线控、交通网络的协调控制——面控；按控制原理划分：定时控制、感应控制、自适应控制。
关于看门狗电路
在由单片机构成的微型计算机系统中,由于单片机的工作常常会受到来自外界电磁
场的干扰,造成程序的跑飞,而陷入死循环,程序的正常运行被打断,由单片机控制的系统无法继续工作,会造成整个系统的陷入停滞状态,发生不可预料的后果,所以出于对单片机运行状态进行实时监测的考虑,便产生了一种专门用于监测单片机程序运行状态的芯片,俗称"看门狗"(watchdog)。
MAX692是微系统监控电路芯片，具有后备电池切换、掉电判别、看门狗监控等功能。其封装和引脚说明如图2所示。
图-2 MAX692封装和引脚
看门狗电路的应用，使单片机可以在无人状态下实现连续工作,其工作原理是:看门狗芯片和单片机的一个I/O引脚相连,该I/O引脚通过程序控制它定时地往看门狗的这个引脚上送入高电平(或低电平),这一程序语句是分散地放在单片机其他控制语句中间的，一旦单片机由于干扰造成程序跑飞后而陷入某一程序段进入死循环状态时,写看门狗引脚的程序便不能被执行,这个时候,看门狗电路就会由于得不到单片机送来的信号,便在它和单片机复位引脚相连的引脚上送出一个复位信号,使单片机发生复位,即程序从程序存储器的起始位置开始执行,这样便实现了单片机的自动复位。
红外检测电路
红外辐射光子在半导体材料中激发非平衡载流子(电子或空穴)，引起电学性能变化。因为载流子不逸出体外，所以称内光电效应。量子光电效应灵敏度高，响应速度比热探测器快得多，是选择性探测器。为了达到最佳性能，一般都需要在低温下工作。光电探测器可分为：
(1) 光导型：又称光敏电阻。入射光子激发均匀半导体中的价带电子越过禁带进入导带并在价带留下空穴，引起电导增加，为本征光电导。从禁带中的杂质能级也可激发光生载流子进入导带或价带，为杂质光电导。截止波长由杂质电离能决定。量子效率低于本征光导，而且要求更低的工作温度。
中文参考文献格式 参考文献（即引文出处）的类型以单字母方式标识： M——专著，C——论文集，N——报纸文章，J——期刊文章，D——学位论文，R——报告，S——标准，P——专利；对于不属于上述的文献类型，采用字母“Z”标识。 参考文献一律置于文末。其格式为： （一）专著 示例 [1] 张志建.严复思想研究[M]. 桂林：广西师范大学出版社，1989. [2] 马克思恩格斯全集：第1卷[M]. 北京：人民出版社，1956. [3] [英]蔼理士.性心理学[M]. 潘光旦译注.北京：商务印书馆，1997. （二）论文集 示例 [1] 伍蠡甫.西方文论选[C]. 上海：上海译文出版社，1979. [2] 别林斯基.论俄国中篇小说和果戈里君的中篇小说[A]. 伍蠡甫.西方文论选：下册[C]. 上海：上海译文出版社，1979. 凡引专著的页码，加圆括号置于文中序号之后。 （三）报纸文章 示例 [1] 李大伦.经济全球化的重要性[N]. 光明日报，1998-12-27，（3） （四）期刊文章 示例 [1] 郭英德.元明文学史观散论[J]. 北京师范大学学报（社会科学版），1995（3）. （五）学位论文 示例 [1] 刘伟.汉字不同视觉识别方式的理论和实证研究[D]. 北京：北京师范大学心理系，1998. （六）报告 示例 [1] 白秀水，刘敢，任保平. 西安金融、人才、技术三大要素市场培育与发展研究[R]. 西安：陕西师范大学西北经济发展研究中心，1998. （七）、对论文正文中某一特定内容的进一步解释或补充说明性的注释，置于本页地脚，前面用圈码标识。 参考文献的类型 根据GB3469-83《文献类型与文献载体代码》规定，以单字母标识： M——专著（含古籍中的史、志论著） C——论文集 N——报纸文章 J——期刊文章 D——学位论文 R——研究报告 S——标准 P——专利 A——专著、论文集中的析出文献 Z——其他未说明的文献类型 电子文献类型以双字母作为标识： DB——数据库 CP——计算机程序 EB——电子公告
英文论文APA格式 英文论文一些格式要求与国内期刊有所不同。从学术的角度讲，它更加严谨和科学，并且方便电子系统检索和存档。 版面格式
表格 表格的题目格式与正文相同，靠左边，位于表格的上部。题目前加Table后跟数字，表示此文的第几个表格。 表格主体居中，边框粗细采用0.5磅；表格内文字采用Times New Roman，10磅。 举例： Table 1. The capitals, assets and revenue in listed banks
图表和图片 图表和图片的题目格式与正文相同，位于图表和图片的下部。题目前加Figure 后跟数字，表示此文的第几个图表。图表及题目都居中。只允许使用黑白图片和表格。 举例： Figure 1. The Trend of Economic Development 注：Figure与Table都不要缩写。 引用格式与参考文献 1. 在论文中的引用采取插入作者、年份和页数方式，如"Doe (2001, p.10) reported that …" or "This在论文中的引用采取作者和年份插入方式，如"Doe (2001, p.10) reported that …" or "This problem has been studied previously (Smith, 1958, pp.20-25)。文中插入的引用应该与文末参考文献相对应。 举例：Frankly speaking, it is just a simulating one made by the government, or a fake competition, directly speaking. (Gao, 2003, p.220). 2. 在文末参考文献中，姓前名后，姓与名之间以逗号分隔；如有两个作者，以and连接；如有三个或三个以上作者，前面的作者以逗号分隔，最后一个作者以and连接。 3. 参考文献中各项目以“点”分隔，最后以“点”结束。 4. 文末参考文献请按照以下格式：
外文文献： Knowledge of the stepper motor What is a stepper motor： Stepper motor is a kind of electrical pulses into angular displacement of the implementing agency. Popular little lesson: When the driver receives a step pulse signal, it will drive a stepper motor to set the direction of rotation at a fixed angle (and the step angle). You can control the number of pulses to control the angular displacement, so as to achieve accurate positioning purposes; the same time you can control the pulse frequency to control the motor rotation speed and acceleration, to achieve speed control purposes. What kinds of stepper motor sub-： In three stepper motors: permanent magnet (PM), reactive (VR) and hybrid (HB) permanent magnet stepper usually two-phase, torque, and smaller, step angle of 7.5 degrees or the general 15 degrees; reaction step is generally three-phase, can achieve high torque output, step angle of 1.5 degrees is generally, but the noise and vibration are large. 80 countries in Europe and America have been eliminated; hybrid stepper is a mix of permanent magnet and reactive advantages. It consists of two phases and the five-phase: two-phase step angle of 1.8 degrees while the general five-phase step angle of 0.72 degrees generally. The most widely used Stepper Motor. What is to keep the torque (HOLDING TORQUE) How much precision stepper motor? Whether the cumulative： The general accuracy of the stepper motor step angle of 3-5%, and not cumulative.
超详细中英文论文参考文献标准格式 1、参考文献和注释。按论文中所引用文献或注释编号的顺序列在论文正文之后，参考文献之前。图表或数据必须注明来源和出处。 （参考文献是期刊时，书写格式为： [编号]、作者、文章题目、期刊名（外文可缩写）、年份、卷号、期数、页码。参考文献是图书时，书写格式为： [编号]、作者、书名、出版单位、年份、版次、页码。） 2、附录。包括放在正文内过份冗长的公式推导，以备他人阅读方便所需的辅助性数学工具、重复性数据图表、论文使用的符号意义、单位缩写、程序全文及有关说明等。 参考文献（即引文出处）的类型以单字母方式标识，具体如下： [M]--专著,著作 [C]--论文集(一般指会议发表的论文续集，及一些专题论文集，如《***大学研究生学术论文集》[N]-- 报纸文章 [J]--期刊文章：发表在期刊上的论文，尽管有时我们看到的是从网上下载的（如知网），但它也是发表在期刊上的，你看到的电子期刊仅是其电子版 [D]--学位论文：不区分硕士还是博士论文 [R]--报告：一般在标题中会有"关于****的报告"字样 [S]-- 标准 [P]--专利 [A]--文章：很少用，主要是不属于以上类型的文章 [Z]--对于不属于上述的文献类型，可用字母"Z"标识，但这种情况非常少见 常用的电子文献及载体类型标识： [DB/OL] --联机网上数据(database online) [DB/MT] --磁带数据库(database on magnetic tape) [M/CD] --光盘图书(monograph on CDROM) [CP/DK] --磁盘软件(computer program on disk) [J/OL] --网上期刊(serial online) [EB/OL] --网上电子公告(electronic bulletin board online) 很显然，标识的就是该资源的英文缩写，/前面表示类型，/后面表示资源的载体，如OL表示在线资源 二、参考文献的格式及举例 1．期刊类 【格式】[序号]作者.篇名[J].刊名,出版年份,卷号(期号)起止页码. 【举例】 [1] 周融，任志国，杨尚雷，厉星星.对新形势下毕业设计管理工作的思考与实践[J].电气电子教学学报，2003(6):107-109. [2] 夏鲁惠.高等学校毕业设计(论文)教学情况调研报告[J].高等理科教育,2004(1):46-52. [3] Heider, E.R.& D.C.Oliver. The structure of color space in naming and memory of two languages [J]. Foreign Language Teaching and Research, 1999, (3): 62 67. 2．专著类
贯彻落实科学发展观大力发展节能与绿色建筑 （2005年2月23日） 中华人民共和国建设部 节能建筑是按节能设计标准进行设计和建造、使其在使用过程中降低能耗的建筑。 绿色建筑是指为人们提供健康、舒适、安全的居住、工作和活动的空间，同时在建筑全生命周期（物料生产，建筑规划、设计、施工、运营维护及拆除过程）中实现高效率地利用资源（能源、土地、水资源、材料）、最低限度地影响环境的建筑物。绿色建筑也有人称之为生态建筑、可持续建筑。 一、发展节能与绿色建筑的重要意义 建筑作为人工环境，是满足人类物质和精神生活需要的重要组成部分。然而，人类对感官享受的过度追求，以及不加节制的开发与建设，使现代建筑不仅疏离了人与自然的天然联系和交流，也给环境和资源带来了沉重的负担。据统计，人类从自然界所获得的50％以上的物质原料用来建造各类建筑及其附属设施，这些建筑在建造与使用过程中又消耗了全球能源的50％左右；在环境总体污染中，与建筑有关的空气污染、光污染、电磁污染等就占了34％；建筑垃圾则占人类活动产生垃圾总量的40％；在发展中国家，剧增的建筑量还造成侵占土地、破坏生态环境等现象日益严重。中国正处于工业化和城镇化快速发展阶段，要在未来15年保持GDP年均增长7％以上，将面临巨大的资源约束瓶颈和环境恶化压力。严峻的事实告诉我们，中国要走可持续发展道路，发展节能与绿色建筑刻不容缓。 绿色建筑通过科学的整体设计，集成绿色配置、自然通风、自然采光、低能耗围护结构、新能源利用、中水回用、绿色建材和智能控制等高新技术，具有选址规划合理、资源利用高效循环、节能措施综合有效、建筑环境健康舒适、废物排放减量无害、建筑功能灵活适宜等六大特点。它不仅可以满足人们的生理和心理需求，而且能源和资源的消耗最为经济合理，对环境的影响最小。 胡锦涛同志指出：要大力发展节能省地型住宅，全面推广节能技术，制定并强制执行节能、节材、节水标准，按照减量化、再利用、资源化的原则，搞好资源综合利用，实现经济社会的可持续发展。温家宝和曾培炎同志也多次指出，建筑节能不仅是经济问题，而且是重要的战略问题。 发展节能与绿色建筑是建设领域贯彻“三个代表”重要思想和十六大精神，认真落实以人为本，全面、协调、可持续的科学发展观，统筹经济社会发展、人与
Structure and function of the MCS-51 series Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have,such as 8051, 8031, 8751, 80C51BH, 80C31BH,etc., their basic composition, basic performance and instruction system are all the same. 8051 daily representatives- 51 serial one-chip computers . An one-chip computer system is made up of several following parts: ( 1) One microprocessor of 8 (CPU). ( 2) At slice data memory RAM (128B/256B),it use not depositting not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. ( 3) Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip computers, such as 8031 , 8032, 80C ,etc.. ( 4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction , may use as exporting too. ( 5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a timing way too, and can according to count or result of timing realize the control of the computer. ( 6) Five cut off cutting off the control system of the source . ( 7) One all duplexing serial I/O mouth of UART (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or one-chip computer and serial communication of computer to use for. ( 8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertas now at most. Every the above-mentioned part was joined through the inside data bus .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command centre, made up of such parts as arithmetic unit and controller , etc.. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 storing device temporarilies of 8, storing device 2 temporarily, 8's accumulation
中英文参考文献格式! (細節也很重要啊。。）来源：李菲玥的日志 规范的参考文献格式 一、参考文献的类型 参考文献（即引文出处）的类型以单字母方式标识，具体如下： M——专著C——论文集N——报纸文章J——期刊文章 D——学位论文R——报告S——标准P——专利 A——文章 对于不属于上述的文献类型，采用字母“Z”标识。 常用的电子文献及载体类型标识： ［ＤＢ/OL］——联机网上数据(database online) ［DB/MT］——磁带数据库(database on magnetic tape) ［Ｍ/CD］——光盘图书(monograph on CD ROM) ［ＣＰ／DK］——磁盘软件(computer program on disk) ［Ｊ／ＯＬ］——网上期刊(serial online) ［ＥＢ/OL］——网上电子公告(electronic bulletin board online) 对于英文参考文献，还应注意以下两点： ①作者姓名采用“姓在前名在后”原则，具体格式是：姓，名字的首字母. 如：Malcolm R ichard Cowley 应为：Cowley, M.R.，如果有两位作者，第一位作者方式不变，&之后第二位作者名字的首字母放在前面，姓放在后面，如：Frank Norris 与Irving Gordon应为：Norri s, F. & I.Gordon.； ②书名、报刊名使用斜体字，如：Mastering English Literature，English Weekly。二、参考文献的格式及举例 1．期刊类 【格式】[序号]作者.篇名[J].刊名，出版年份，卷号（期号）：起止页码. 【举例】 [1] 周融，任志国，杨尚雷，厉星星.对新形势下毕业设计管理工作的思考与实践[J].电气电子教学学报，2003(6)：107-109.
动脉粥样硬化所导致的心脑血管疾病是目前发病率和死亡率较高的疾病之一。在动脉粥样硬化的形成过程中, 内皮细胞病变是其中极其重要的因素，最显著的变化是动脉内皮功能紊乱, 血管内皮细胞的损伤和功能改变是动脉粥样硬化发生的起始阶段。 Cardiovascular and cerebrovascular disease caused by atherosclerosis is one of diseases with higher mortality and morbidity at present . In the formation of atherosclerosis, the endothelial cell lesion is one of the most important factors, in which, the most significant change is endothelial dysfunction. In addition, the injuries and the changes of vascular endothelial cells are the initial factors of atherosclerosis. 许多因素会导致血管内皮细胞受损, 主要包括脂多糖(Lipopolysaccharides , LPS)、炎症介质、氧自由基等。其中脂多糖因其广泛的生物学作用, 越来越引起研究者的关注。LPS 是一种炎症刺激物, 是革兰阴性杆菌细胞壁的主要组成成分，其通过刺激血管内皮细胞，引起其相关细胞因子和炎性因子的表达紊乱，尤其是Ca2+ 和活性氧簇(Reactive Oxygen Species , ROS的合成和释放发生改变诱导细胞氧化应激内环境紊乱。大量研究表明, LPS 直接参与动脉粥样硬化的形成过程, 特别是动脉粥样硬化血管炎症的初始阶段, LPS可通过直接作用或间接影响的方式激活并损伤内皮细胞，从而引 起血管内皮细胞形态与功能的改变。 Many factors induce vascular endothelial cell damage, including lipopolysaccharides (LPS), inflammatory mediators and oxygen free
英文引用及参考文献格式要求 一、参考文献的类型 参考文献（即引文出处）的类型以单字母方式标识，具体如下： M——专著C——论文集N——报纸文章 J——期刊文章D——学位论文R——报告 对于不属于上述的文献类型，采用字母“Z”标识。 对于英文参考文献，还应注意以下两点： ①作者姓名采用“姓在前名在后”原则，具体格式是：姓，名字的首字母.如：MalcolmRichardCowley应为：Cowley,M.R.，如果有两位作者，第一位作者方式不变，&之后第二位作者名字的首字母放在前面，姓放在后面，如：FrankNorris与IrvingGordon应为：Norris,F.&I.Gordon.； ②书名、报刊名使用斜体字，如：MasteringEnglishLiterature，EnglishWeekly。 二、参考文献的格式及举例 1.期刊类 【格式】[序号]作者.篇名[J].刊名，出版年份，卷号（期号）：起止页码. 【举例】 [1]王海粟.浅议会计信息披露模式[J].财政研究，2004,21(1)：56-58. [2]夏鲁惠.高等学校毕业论文教学情况调研报告[J].高等理科教育，2004(1):46-52. [3]Heider,E.R.&D.C.Oliver.Thestructureofcolorspaceinnamingandmemo ryoftwolanguages[J].ForeignLanguageTeachingandResearch,1999,(3):62–6 7. 2.专著类 【格式】[序号]作者.书名[M].出版地：出版社，出版年份：起止页码. 【举例】[4]葛家澍，林志军.现代西方财务会计理论[M].厦门：厦门大学出版社，2001：42. [5]Gill,R.MasteringEnglishLiterature[M].London:Macmillan,1985:42-45. 3.报纸类 【格式】[序号]作者.篇名[N].报纸名，出版日期（版次）. 【举例】 [6]李大伦.经济全球化的重要性[N].光明日报，1998-12-27(3). [7]French,W.BetweenSilences:AVoicefromChina[N].AtlanticWeekly,198 715(33). 4.论文集 【格式】[序号]作者.篇名[C].出版地：出版者，出版年份：起始页码. 【举例】 [8]伍蠡甫.西方文论选[C].上海：上海译文出版社，1979：12-17. [9]Spivak,G.“CantheSubalternSpeak?”[A].InC.Nelson&L.Grossberg(e ds.).VictoryinLimbo:Imigism[C].Urbana:UniversityofIllinoisPress,1988, pp.271-313.
(文档含英文原文和中文翻译) 中英文翻译 平面设计 任何时期平面设计可以参照一些艺术和专业学科侧重于视觉传达和介绍。采用多种方式相结合，创造和符号，图像和语句创建一个代表性的想法和信息。平面设计师可以使用印刷，视觉艺术和排版技术产生的最终结果。平面设计常常提到的进程，其中沟通是创造和产品设计。 共同使用的平面设计包括杂志，广告，产品包装和网页设计。例如，可能包括产品包装的标志或其他艺术作品，举办文字和纯粹的设计元素，如形状和颜色统一件。组成的一个最重要的特点，尤其是平面设计在使用前现有材料或不同的元素。 平面设计涵盖了人类历史上诸多领域，在此漫长的历史和在相对最近爆炸视觉传达中的第20和21世纪，人们有时是模糊的区别和重叠的广告艺术，平面设计和美术。毕竟，他们有着许多相同的内容，理论，原则，做法和语言，有时同样的客人或客户。广告艺术的最终目标是出售的商品和服务。在平面
设计，“其实质是使以信息，形成以思想，言论和感觉的经验”。 在唐朝（ 618-906 ）之间的第4和第7世纪的木块被切断打印纺织品和后重现佛典。阿藏印在868是已知最早的印刷书籍。 在19世纪后期欧洲，尤其是在英国，平面设计开始以独立的运动从美术中分离出来。蒙德里安称为父亲的图形设计。他是一个很好的艺术家，但是他在现代广告中利用现代电网系统在广告、印刷和网络布局网格。 于1849年，在大不列颠亨利科尔成为的主要力量之一在设计教育界，该国政府通告设计在杂志设计和制造的重要性。他组织了大型的展览作为庆祝现代工业技术和维多利亚式的设计。 从1892年至1896年威廉?莫里斯凯尔姆斯科特出版社出版的书籍的一些最重要的平面设计产品和工艺美术运动，并提出了一个非常赚钱的商机就是出版伟大文本论的图书并以高价出售给富人。莫里斯证明了市场的存在使平面设计在他们自己拥有的权利，并帮助开拓者从生产和美术分离设计。这历史相对论是，然而，重要的，因为它为第一次重大的反应对于十九世纪的陈旧的平面设计。莫里斯的工作，以及与其他私营新闻运动，直接影响新艺术风格和间接负责20世纪初非专业性平面设计的事态发展。 谁创造了最初的“平面设计”似乎存在争议。这被归因于英国的设计师和大学教授Richard Guyatt，但另一消息来源于20世纪初美国图书设计师William Addison Dwiggins。 伦敦地铁的标志设计是爱德华约翰斯顿于1916年设计的一个经典的现代而且使用了系统字体设计。 在20世纪20年代，苏联的建构主义应用于“智能生产”在不同领域的生产。个性化的运动艺术在俄罗斯大革命是没有价值的，从而走向以创造物体的功利为目的。他们设计的建筑、剧院集、海报、面料、服装、家具、徽标、菜单等。 Jan Tschichold 在他的1928年书中编纂了新的现代印刷原则，他后来否认他在这本书的法西斯主义哲学主张，但它仍然是非常有影响力。 Tschichold ，包豪斯印刷专家如赫伯特拜耳和拉斯洛莫霍伊一纳吉，和El Lissitzky 是平面设计之父都被我们今天所知。 他们首创的生产技术和文体设备，主要用于整个二十世纪。随后的几年看到平面设计在现代风格获得广泛的接受和应用。第二次世界大战结束后，美国经济的建立更需要平面设计，主要是广告和包装等。移居国外的德国包豪斯设计学院于1937年到芝加哥带来了“大规模生产”极简到美国;引发野火的“现代”建筑和设计。值得注意的名称世纪中叶现代设计包括阿德里安Frutiger ，设计师和Frutiger字体大学;保兰德，从20世纪30年代后期，直到他去世于1996年，采取的原则和适用包豪斯他们受欢迎的广告和标志设计，帮助创造一个独特的办法，美国的欧洲简约而成为一个主要的先驱。平面设计称为企业形象;约瑟夫米勒，罗克曼，设计的海报严重尚未获取1950年代和1960年代时代典型。 从道路标志到技术图表，从备忘录到参考手册，增强了平面设计的知识转让。可读性增强了文字的视觉效果。 设计还可以通过理念或有效的视觉传播帮助销售产品。将它应用到产品和公司识别系统的要素像标志、颜色和文字。连同这些被定义为品牌。品牌已日益成为重要的提供的服务范围，许多平面设计师，企业形象和条件往往是同时交替使用。
广东工业大学 本科毕业设计（论文） 外文参考文献译文及原文 系部 专业自动化 年级 2006级 班级名称 学号 学生姓名 指导教师 2009年6月 目录 外文文献译文 (1) 1.单片机定义 (1) 2.单片机介绍 (2)
3.单片机历史 (3) 4.单片机的应用领域 (4) 5.at89c52单片机介绍 (6) 外文文献原文 (8) 1. The definition of a single-chip (8) 2. single-chip introduced (9) 3. single-chip history (11) 4. single-chip applications (12) 5.at89c52 chip explains (14)
外文文献译文 1.单片机定义 单片机是指一个集成在一块芯片上的完整计算机系统。尽管他的大部分功能集成在一块小芯片上，但是它具有一个完整计算机所需要的大部分部件：CPU、内存、内部和外部总线系统，目前大部分还会具有外存。同时集成诸如通讯接口、定时器，实时时钟等外围设备。而现在最强大的单片机系统甚至可以将声音、图像、网络、复杂的输入输出系统集成在一块芯片上。 单片机也被称为微控制器（Microcontroller），是因为它最早被用在工业控制领域。单片机由芯片内仅有CPU的专用处理器发展而来。最早的设计理念是通过将大量外围设备和CPU集成在一个芯片中，使计算机系统更小，更容易集成进复杂的而对体积要求严格的控制设备当中。INTEL的Z80是最早按照这种思想设计出的处理器，从此以后，单片机和专用处理器的发展便分道扬镳。 早期的单片机都是8位或4位的。其中最成功的是INTEL的8031，因为简单可靠而性能不错获得了很大的好评。此后在8031上发展出了MCS51系列单片机系统。基于这一系统的单片机系统直到现在还在广泛使用。随着工业控制领域要求的提高，开始出现了16位单片机，但因为性价比不理想并未得到很广泛的应用。90年代后随着消费电子产品大发展，单片机技术得到了巨大的提高。随着INTEL i960系列特别是后来的ARM系列的广泛应用，32位单片机迅速取代16位单片机的高端地位，并且进入主流市场。而传统的8位单片机的性能也得到了飞速提高，处理能力比起80年代提高了数百倍。目前，高端的32位单片机主频已经超过300MHz，性能直追90年代中期的专用处理器，而普通的型号出厂价格跌落至1美元，最高端的型号也只有10美元。当代单片机系统已经不再只在裸机环境下开发和使用，大量专用的嵌入式操作系统被广泛应用在全系列的单片机上。而在作为掌上电脑和手机核心处理的高端单片机甚至可以直接使用专用的Windows和Linux操作系统。 单片机比专用处理器更适合应用于嵌入式系统，因此它得到了最多的应用。
中英文对照翻译 (文档含英文原文和中文翻译) Policies for Development of Iron and Steel Industry The iron and steel industry is an important basic industry of the national economy, a supporting industry for realizing the industrialization and an intensive industry in technologies, capital, resources and energy, and its development requires a comprehensive balancing of all kinds of external conditions. China is a big developing country with a comparatively big demand of iron and steel in the economic development for a long time to go. China's production capacity of iron and steel has ranked the first place in the world for many years. However, there is a large gap in terms of the technological level and material consumption of the iron and steel industry compared with the international advanced level, so the focus of development for the future shall be put on technical upgrading and structural adjustment. In order to enhance the whole technical level of the iron and steel industry, promote the structural adjustment, improve the industrial layout, develop a recycling economy, lower the consumption of materials and energy, pay attention to the environmental protection, raise the comprehensive competitive capacity of enterprises, realize the industrial upgrading, and develop the iron and steel industry into an industry with
液位控制系统论文中英文资料对照外文翻译 The liquid level control system based on dde\matlab\simulink Process control is an important application field of automatic technology, it is to point to the level, temperature, flow control process variables, such as in metallurgy, machinery, chemical, electric power, etc can be widely used. Especially liquid level control technology in real life, played an important role in production, for example, the water supply, civil water tower if low water levels, can affect people's lives in water; Industrial enterprises with water, if the drainage water drainage or controlled properly or not, in relation to the workshop of condition; Boiler drum, if the control level boiler is too low, can make level boiler overheating, possible accident; Jing flow, liquid level control tower control accuracy and level of the craft can influence the quality of the products and the cost, etc. In these production field, are basically labor strength or the operation has certain risk nature of work, extremely prone to accidents caused by operating error, the losses, killing manufacturer. Visible, in actual production, liquid level control accuracy and control effects directly affect the factory production cost and economic benefit of safety coefficient. Even equipment So, in order to ensure safety, convenient operation, you have to research the development of a d v a n c e d l e v e l c o n t r o l m e t h o d s a n d s t r a t e g i e s. The graduation design topic is the liquid level control system based on dde\matlab\simulink\force control, Among them was controlled object for tank level, Communication mode for DDE communications , Matlab is mainly used in the simulation test ,And force control software used for modeling, This system mainly through combination of hardware and software device to achieve precise control of liquid level , In modern industry level control of important component, it influence upon production not allow to ignore, in order to ensure safety in production and the product quality and quantity, the level and perform effective control is very necessary, The following is a description of all aspects：
The Introduction of AT89C51 Description The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K bytes of Flash programmable and erasable read only memory (PEROM). The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-standard MCS-51 instruction set. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides a highly-flexible and cost-effective solution to many embedded control applications. Function characteristic The AT89C51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit timer/counters, one 5 vector two-level interrupt architecture, a full duplex serial port, one-chip oscillator and clock circuitry. In addition, the AT89C51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port and interrupt system to continue functioning. The Power-down Mode saves the RAM contents but freezes the oscillator disabling all other chip functions until the next hardware reset. Pin Description VCC：Supply voltage. GND：Ground.