、冲压、喷漆等专业词汇
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板
barcode条形码
barcode scanner条形码扫描仪fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
cosmetic inspect外观检查
inner parts inspect内部检查thumb screw大头螺丝
lbs.inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis |'∫?si| 基座
bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试Voltage switch of SPS
电源电压接柆键
sheet metal parts 冲件plastic parts塑料件
SOP制造作业程序
material check list物料检查表
work cell工作间
trolley台车
carton纸箱
sub-line支线
left fork叉车
Personnel resource department
人力资源部
production department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot机械手
hydraulic machine油压机
lathe车床
planer |'plein |刨床
miller铣床
grinder磨床
driller钻床
linear cutting线切割
electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager |'depjuti| =vice
manager副理
section supervisor课长
deputy section supervisor =vice
section supervisor副课长
group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skr?pid|报废
scrape ..v.刮;削
deficient purchase来料不良
manufacture procedure制程
deficient manufacturing procedure
制程不良
oxidation |' ksi'dei n|氧化
scratch刮伤
dents压痕
defective upsiding down抽芽不良
defective to staking铆合不良
embeded lump|in'bed| |l mp|镶块
feeding is not in place送料不到位
stamping-missing漏冲
production capacity生产力
education and training教育与训练
proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称administration/general affairs dept
总务部
automatic screwdriver电动启子thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzer蜂鸣器
defective product label不良标签identifying sheet list标示单screwdriver holder起子插座
pedal踩踏板
stopper阻挡器
flow board流水板
hydraulic handjack油压板车
forklift叉车
pallet栈板
glove(s)手套
glove(s) with exposed fingers割手套thumb大拇指
forefinger食指
midfinger中指
ring finger无名指
little finger小指
band-aid创可贴
industrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头sweeper扫把
mop拖把
vacuum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain链条jack升降机
production line流水线
chain链条槽
magnetizer加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸
偏大(小)
cosmetic defect外观不良
slipped screwhead / slippery screw
head螺丝滑头
slipped screwhead / shippery
screw thread滑手
speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
poor staking铆合不良
excessive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of packaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise
expansion projects企划
QC品管
die worker模工
production, to produce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
culture教养
qualified products, up-to-grade
products良品
defective products, not up-to-grade
products不良品
waste废料
board广告牌
feeder送料机
sliding rack滑料架
defective product box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料
to impose lines压线
to compress, compressing压缩character die字模
to feed, feeding送料
transportation运输
(be)qualified, up to grade合格
not up to grade, not qualified不合格material change, stock change材料变更
feature change 特性变更
evaluation评估
prepare for, make preparations for
准备
parameters参数
rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
manufacture procedure制程operation procedure作业流程
to revise, modify修订
to switch over to, switch---to
throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模
automation自动化
to stake, staking, riveting铆合
add lubricating oil加润滑油
shut die架模shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
Vocabulary for stamping
冲压常词汇
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block
stop 定位块
reset复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
To return/delivery to. to send
delivery back to return of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked
断裂
to lubricate润滑
common vocabulary for die
engineering模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cut edges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line stretching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人equipment设备
waste materials废料
work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量Quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查end-user/using unit(department)使
用单位
Summary of year-end physical
inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory
list will be sent to accounting
department together (Those of
NHK will be sent to financial
department)
本表请与盘点清册一起送会计部-
(NHK厂区送财会部)
Application status records of
year-end physical inventory List
and physical inventory card 年终
盘点卡与清册使用-状况明细表
Blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold
testing工程试模材料
not included in physical inventory
不列入盘点
sample样品
incoming material to be inspected
进货待验
description品名
steel/rolled steel钢材
Material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by /
prepared by核准/审核/承办
PCE assembly production
schedule sheet
PCE组装厂生产排配表
model机锺
work order工令
revision版次
remark备注
production control confirmation生
产确认
checked by初审
approved by核准
department部门
Stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
Year-end physical inventory
difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity账面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品packing materials包材
good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品
disposed goods处理品warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list 备品盘点清单
spare molds location模具备品仓skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆
spring-box eject-plate弹簧箱顶板
bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品
coordinate坐标
dismantle the die折模
auxiliary function辅助功能
poly-line多义线
heater band 加热片
thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应
ram连杆
edge finder巡边器
concave凸
convex凹
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金
magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blister气泡
fillet镶;嵌边
through-hole form通孔形式
roller pin formality滚针形式
cam driver铡楔
shank摸柄
crank shaft曲柄轴
angular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉
dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒
pin销
lifter guide pin浮升导料销
guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子
ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子guide plate定位板
sliding block滑块
sliding dowel block滑块固定块active plate活动板
lower sliding plate下滑块板upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
cover plate盖板
guide pad导料块
塑件&模具相关英文compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
移转成型用模具
encapsulation molding低压封装成型
射出成型用模具
two plate两极式(模具)
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器
spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
h=0.02~0.05mm
w=3.2mm
L=3~5mm
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleeve套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板
guide pin导销
eject rod (bar)(成型机)顶业捧
subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂
orientation定向
sprue gate射料浇口,直浇口
nozzle射嘴
sprue lock pin料头钩销(拉料杆)
slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口
H=F=1/2t~1/5t
T=2.5~3.5mm
diaphragm gate隔膜浇口
ring gate环形浇口
submarine gate潜入式浇口
tunnel gate隧道式浇口
pin gate针点浇口
Φ0.8~1.0mm
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
质量人员名称类
QC quality control 品质管理人员
FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理
POC passage quality control 段检人员
QA quality assurance 质量保证人员
OQA output quality assurance 出货质量保证人员
QE quality engineering 质量工程人员
质量保证类
FAI first article inspection 新品首件检查
FAA first article assurance 首件确认
TVR tool verification report 模具确认报告
3B 3B 模具正式投产前确认CP capability index 能力指数
CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查
QFD quality function deployment 质量机能展开
FMEA failure model effectiveness analysis 失效模式分析
8D 8 disciplines 8项回复内容
FA final audit 最后一次稽核
CAR corrective action request 改正行动要求
corrective action report 改正行动报告
FQC运作类
AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收
REE Reject 拒收
CR Critical 极严重的
MAJ Major 主要的
MIN Minor 轻微的
AOQ Average Output Quality 平均出厂质量
AOQL Average Output Quality Level 平均出厂质量
Q/R/S Quality/Reliability/Service 质量/可靠度服务
MIL-STD Military-Standard 军用标准
S I-S IV Special I-Special IV 特殊抽样水平等级
P/N Part Number 料号
L/N Lot Number 特采
AOD Accept On Deviation 特采
UAI Use As It 首件检查报告
FPIR First Piece Inspection Report 百万分之一
PPM Percent Per Million 批号
制程统计品管专类
SPC Statistical Process Control 统计制程管制
SQC Statistical Quality Control 统计质量管理
R Range 全距
AR Average Range 全距平均值
UCL Upper Central Limit 管制上限
LCL Lower Central Limit 管制下限
MAX Maximum 最大值
MIN Minimum 最小值
GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸
DIA Diameter 直径
FREQ Frequency 频率
N Number 样品数
其它质量术语类
QCC Quality Control Circle 品质圈
QIT Quality Improvement Team 质量改善小组
PDCA Plan Do Check Action 计划执行检查总结
ZD Zero Defect 零缺点
QI Quality Improvement 质量改善
QP Quality Policy 目标方针
TQM Total Quality Management 全面质量管理
MRB Material Reject Bill 退货单
LQL Limiting Quality Level 最低质量水平
RMA Return Material Audit 退料认可
QAN Quality Ameliorate Notice 质量改善活动
ADM Absolute Dimension Measurement 全尺寸测量
QT Quality Target 质量目标
7QCTools 7 Quality Control Tools 品管七大手法
通用之件类
ECN Engineering Change Notes 工程变更通知(供货商)
ECO Engineering Change Order 工程改动要求(客户)
PCN Process Change Notice 工序改动通知
PMP Product Management Plan 生产管制计划
SIP Specification In Process 制程检验规格
SOP Standard Operation Procedure 制造作业规范
IS Inspection Specification 成品检验规范
BOM Bill Of Material 物料清单
PS Package Specification 包装规范
SPEC Specification 规格
DWG Drawing 图面
系统文件类
QC Quality System 质量系统
ES Engineering Standardization 工程标准
CGOO China General PCE龙华厂文件
H Huston (美国)休斯敦
C Compaq (美国)康伯公司
C China 中国大陆
A Assembly 组装(厂)
S Stamping 冲压(厂)
P Painting 烤漆(厂)
I Intel 英特尔公司
T TAIWAN 台湾
IWS International Workman Standard 工艺标准
ISO International Standard Organization 国际标准化组织
GS General Specification 一般规格
CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类
PMC Production & Material Control 生产和物料控制
PPC Production Plan Control 生产计划控制
MC Material Control 物料控制
ME Manufacture Engineering 制造工程部
PE Project Engineering 产品工程部
A/C Accountant Dept 会计部
P/A Personal & Administration 人事行政部
DC Document Center 资料中心
QE Quality Engineering 质量工程(部)
QA Quality Assurance 质量保证(处)
QC Quality Control 质量管理(课)
PD Product Department 生产部
LAB Library 实验室
IE Industrial Engineering 工业工程
R&D Research & Design 设计开发部
P Painting 烤漆(厂)
A Assembly 组装(厂)
S Stamping 冲压(厂)
生产类
PCS Pieces 个(根,块等)
PRS Pairs 双(对等)
CTN Carton 卡通箱
PAL Pallet/skid 栈板
PO Purchasing Order 采购订单
MO Manufacture Order 生产单
D/C Date Code 生产日期码
ID/C Identification Code (供货商)识别码
SWR Special Work Request 特殊工作需求
L/N Lot Number 批号
P/N Part Number 料号
其它
OEM Original Equipment Manufacture 原设备制造
PCE Personal Computer Enclosure 个人计算机外设
PC Personal Computer 个人计算机
CPU Central Processing Unit 中央处理器
SECC SECC` 电解片
SGCC SGCC 热浸镀锌材料
NHK North of Hongkong 中国大陆
PRC People's Republic of China 中国大陆
U.S.A the United States of America 美国
A.S.A.P As Soon As Possible 尽可能快的
E-MAIL Electrical-Mail 电子邮件
N/A Not Applicable 不适用
QTY Quantity 数量
VS 以及
REV Revision 版本
JIT Just In Time 零库存
I/O Input/Output 输入/输出
OK Ok 好
NG Not Good 不行,不合格
C=0 Critical=0 极严重不允许
ESD Electry-static Discharge 静电排放
5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会
CC Carbon Copy 副本复印相关人员
APP Approve 核准,认可,承认
CHK Check 确认
AM Ante Meridian 上午
PM Post Meridian 下午
CD Compact Disk 光盘
CD-ROM Compact Disk Read-Only Memory 只读光盘
FDD Floppy Disk Drive 软盘机
HDD Hard Disk Drive 碟碟机
REF Reference 仅供参考
CONN Connector 连接器
CAV Cavity 模穴
CAD Computer Aid Design 计算器辅助设计
ASS'Y Assembly 装配,组装
MAT'S Material 材料
IC Integrated Circuit 集成电路
T/P True Position 真位度
TYP Type 类型
WDR Weekly Delivery Requirement 周出货需求
C?T Cycle Time 制程周期
L/T Lead Time 前置时间(生产前准备时间)
S/T Standard Time 标准时间
P/M Product Market 产品市场
3C Computer,Commumcation,Consumer electronic's 消费性电子
5WIH When,Where,Who,What,Why,How to
5M Man,Machine,Material,Method,Measurement
4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证
DQA Design Quality Assurance 设计质量保证
MQA Manufacture Quality Assurance 制造质量保证
SSQA Sales and service Quality Assurance 销售及服务质量保证
LRR Lot Reject Rate 批退率
BS Brain storming 脑力激荡
EMI Electronic Magnet Inspect 高磁测试
FMI Frequency Modulated Inspect 高频测试
B/M Boar/Molding (flat cable)
C/P Connector of PC
A/P Assembly
SPS Switching power supply 电源箱
DT Desk Top 卧式(机箱)
MT Mini-Tower 立式(机箱)
DVD Digital Video Disk
VCD Video Compact Disk
LCD Liquid Crystal Display
CAD Computer AID Design
CAM Computer AID Manufacturing
CAE Computer AID Engineering
ABIOS Advanced Basic in put/output system 先进的基本输入/输出系统CMOS Complementary Metal-Oxide-Semiconductor Transistor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理
IC Integrated Circuit 集成电路
ISA Industry Standard Architecture 工业标准体制结构
MCA Micro Channel Architecture 微信道结构
EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件
DIMM Dual in-line Memory Module 双项导通汇流组件
LED Light-Emitting Diode 发光二级管
FMEA Failure Mode Effectiveness 失效模式分析
W/H Wire Harness 金属线绪束集组件
F/C Flat Cable 排线
PCB Printed Circuit Board 印刷电路板
CAR Correction Action Report 改善报告
NG Not Good 不良
WPR Weekly Delivery Requirement 周出货要求
PPM Parts Per Million 百万分之一
TPM Total Production Maintenance 全面生产保养
MRP Material Requirement Planning 物料需计划
OS Operation System 操作系统
TBA To Be Design 待定,定缺
D/C Drawing Change
P/P Plans & Procedure
EMI Electrical-Music Industry 电子音乐工业
RFI Read Frequency Input 读频输入
MMC Maximum Material Condition
MMS Maximum Material Size
LMC Least Material Condition
LMS Least Material Size
学习本课程的主要收获: 第一:学习了大量专业词汇和缩略语 例如: Electronic devices Electronic circuits Electronic system components Electronic systems Modern digital design Signal processing technology Audio&voice Image & video Embedded applications Instrument &measurement 脉冲编码调制 人工智能 artificial intelligence 低功耗 low power consumption 信号处理 signal processing 智能机器 intelligent machine 无人机 unmanned aerial vehicle 无处不在 ubiquity [ju:?b?kw?t?s] 物联网 Internet of things 人机界面human-computer interface;man-machine interface 混合现实 Mixed Reality 深亚微米 deep submicron ['s?b'ma?kr?n] triode vacuum tube 三极真空管[?trai?ud] [?v?kju?m] broadcasting n.广播[?br?:dkɑ:st] broadcasting station 广播电台,广播站 commercial broadcasting n.商业广播 [k??m?:??l] amplitude modulation(AM) 调幅['?mplitju:d] frequency modulation(FM)调频 等等 第二:学习了一些常见的专业英语语法 (1)专业英语的语法特点 1.词汇 ⑴大量使用专业词汇和半专业词汇 例如:calculus( ['k?lkjul?s]微积分学), bandwidth(带宽),flip-flop(触发器)等专业词汇,而series,work等是半专业词汇 在不同的学科领域含义有所不同 例如:series可作“级数”(数学)解,也可作“串联”(电学)解。 ⑵大量使用词缀和词根 例如,外语教学与研究出版社出版的《英汉双解信息技术词典》中以tele-构成的单词有30个。 tele 电视 , tele- ['teli]表示“远距离传递,电视”之义
生产制造管理中常用英文单词缩写 1. A/D/V Analysis/Development/Validation 分析/发展/验 证 AA Approve Architecture 审批体系 ACD Actual Completion Date 实际完成日期 ALBS Assembly Line Balance System 装配线平衡系统 ANDON 暗灯(安腾灯) AP Advanced Purchasing 提前采购 API Advanced Product Information 先进的产品信息APQP Advanced Product Quality Planning 先期产品质量策划 ATT Actual Tact Time 实际单件工时 BIQ Building in Quality 制造质量 BIW Body In White 白车身 BOD Bill of Design 设计清单 BOE Bill of Equipment 设备清单 BOL Bill of Logistic 装载清单 BOM Bill of Material 原料清单 BOP Bill of Process 过程清单 BPD Business Plant Deployment 业务计划实施 CAD Computer-Aided Design 计算机辅助设计 CAE Computer-Aided Engineering 计算机辅助工程(软件) CARE Customer Acceptance & Review Evaluation 用户接受度和审查评估 CAS Concept Alternative Selection 概念可改变的选择CIP Continue Improve Process 持续改进 CIT Compartment Integration Team 隔间融合为组 CKD Complete Knockdown 完全拆缷 CMM Coordinate Measuring Machines 坐标测量仪 CPV Cost per Vehicle 单车成本 CR&W Controls/Robotics & Welding 控制/机器人技术和焊接 CS Contract Signing 合同签订
硬件类常用英语词汇 下面是小编整理的硬件类常用英语词汇,希望对大家有帮助。 计算机英语词汇大全 常见硬件篇 CPU:Central Processing Unit,中央处理单元,又叫中央处理器或微处理器,被喻为电脑的心脏。 LD:Laser Disk,镭射光盘,又称激光视盘。 CD:Compact Disc,压缩光盘,又称激光唱盘。 CD-ROM:Compact Disc-Read Only Memory,压缩光盘-只读记忆(存储),又叫“只读光盘”。 VCD:Video Compact Disc,视频压缩光盘,即人们通常所说的“小影碟”。 RAM:Random Access Memory,随机存储器,即人们常说的“内存”。 ROM:Read-Only Memory,只读存储器。 Seagate:美国希捷硬盘生产商。Seagate英文意思为“通往海洋的门户”,常指通海的运河等。 Quantum:英文含意为“定量,总量”。著名硬盘商标,美国昆腾硬盘生产商(Quantum Corporation)。
Maxtor:“水晶”,美国Maxtor硬盘公司。 PCI:Peripheral Component Interconnection,局部总线(总线是计算机用于把信息从一个设备传送到另一个设备的高速通道)。PCI总线是目前较为先进的一种总线结构,其功能比其他总线有很大的提高,可支持突发读写操作,最高传输率可达132Mbps,是数据传输最快的总线之一,可同时支持多组外围设备。PCI不受制于 CPU处理器,并能兼容现有的各种总线,其主板插槽体积小,因此成本低,利于推广。 EDO:Extended Data Output,扩充数据输出。当CPU的处 理速度不断提高时,也相应地要求不断提高DRAM传送数据速度, 一般来说,FPM(Fast Page Model)DRAM传送数据速度在60-70ns,而EDO DRAM比FPM快3倍,达20ns。目前最快的是SDRAM(Synchronous DRAM,同步动态存储器),其存取速度高 达10ns。 SDRAM:Synchronous Dynamic Random Access Memory,同步动态随机存储器,又称同步DRAM,为新一代动态 存储器。它可以与CPU总线使用同一个时钟,因此,SDRAM存储 器较EDO存储器能使计算机的性能大大提高。 Cache:英文含义为“(勘探人员等贮藏粮食、器材等的)地窖; 藏物处”。电脑中为高速缓冲存储器,是位于CPU和主存储器 DRAM(Dynamic Randon Access Memory)之间,规模较小,但 速度很高的存储器,通常由SRAM(Static Random Access
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
Words & Phrases PART ONE 1.individual 个人 2.be responsible for 对…..负责 3.in case of 万一 4.emergency 紧急 5.abandon 放弃;遗弃 6.panic 惊慌 https://www.doczj.com/doc/35141269.html,e over 过来 https://www.doczj.com/doc/35141269.html,e across 偶遇、碰到 9.deposit 押金 10.insure 保险 11.resign 辞职 12.get rid of 除掉 13.fragile 易碎的 14.recycling 回收;循环利用 15.produce 生产 16.product 产品 17.assembly 装配 18.test 测试 19.production operator=machine operator 操作工 20.quality 质量 21.inspector 检测员 22.quality control==QC 质量控制,质量管理 23.shift 轮班 24.8-hour shift / 12-hour shift 8 / 12 小时轮班 25.work on shift 上轮班工 26.shift allowance 轮班津贴 27.accommodation allowance 住宿津贴 28.ask for leave 请假 29.sick leave 病假 30.rejected 不合格的;被拒绝的;被淘汰的 31.rejected part 不合格零件 32.accepted 合格的;被接受的;被选中的 33.accepted part 合格零件 34.error 错误 35.fail 失败;不合格 36.pass 通过;合格 37.conflict 冲突 38.agree 同意 39.show 展示;出示;指给。。。。。。看 40.hobby 爱好 41.shortsighted 近视 42.strong point 强项;优点 43.weak point 弱项;不足之处 44.advantage 优点;优势 45.shortcoming 短处;不足之处 46.disadvantage 缺点;劣势 47.weakness 弱点 48.punctual 准时的;守时的 49.be late for 做。。。。。。迟到 50.on time 准时
transistor n 晶体管 diode n 二极管semiconductor n 半导体 resistor n 电阻器 capacitor n 电容器 alternating adj 交互的 amplifier n 扩音器,放大器integrated circuit 集成电路 linear time invariant systems 线性时不变系统voltage n 电压,伏特数 tolerance n 公差;宽容;容忍condenser n 电容器;冷凝器dielectric n 绝缘体;电解质electromagnetic adj 电磁的 adj 非传导性的 deflection n偏斜;偏转;偏差 linear device 线性器件 the insulation resistance 绝缘电阻 anode n 阳极,正极 cathode n 阴极 breakdown n 故障;崩溃 terminal n 终点站;终端,接线端emitter n 发射器 collect v 收集,集聚,集中insulator n 绝缘体,绝热器oscilloscope n 示波镜;示波器 gain n 增益,放大倍数 forward biased 正向偏置 reverse biased 反向偏置 P-N junction PN结 MOS(metal-oxide semiconductor)金属氧化物半导体 enhancement and exhausted 增强型和耗尽型 integrated circuits 集成电路 analog n 模拟 digital adj 数字的,数位的horizontal adj, 水平的,地平线的vertical adj 垂直的,顶点的amplitude n 振幅,广阔,丰富attenuation n衰减;变薄;稀薄化multimeter n 万用表 frequency n 频率,周率 the cathode-ray tube 阴极射线管 dual-trace oscilloscope 双踪示波器 signal generating device 信号发生器 peak-to-peak output voltage 输出电压峰峰值sine wave 正弦波 triangle wave 三角波 square wave 方波 amplifier 放大器,扩音器 oscillator n 振荡器 feedback n 反馈,回应 phase n 相,阶段,状态 filter n 滤波器,过滤器 rectifier n整流器;纠正者 band-stop filter 带阻滤波器 band-pass filter 带通滤波器 decimal adj 十进制的,小数的hexadecimal adj/n十六进制的 binary adj 二进制的;二元的octal adj 八进制的 domain n 域;领域 code n代码,密码,编码v编码 the Fourier transform 傅里叶变换 Fast Fourier Transform 快速傅里叶变换microcontroller n 微处理器;微控制器assembly language instrucions n 汇编语言指令 chip n 芯片,碎片 modular adj 模块化的;模数的 sensor n 传感器 plug vt堵,塞,插上n塞子,插头,插销coaxial adj 同轴的,共轴的 fiber n 光纤relay contact 继电接触器 single instruction programmer 单指令编程器 dedicated manufactures programming unit 专 供制造厂用的编程单元 beam n (光线的)束,柱,梁 polarize v(使)偏振,(使)极化 Cathode Ray Tube(CRT)阴极射线管 neuron n神经元;神经细胞 fuzzy adj 模糊的 Artificial Intelligence Shell 人工智能外壳程序 Expert Systems 专家系统 Artificial Intelligence 人工智能 Perceptive Systems 感知系统 neural network 神经网络 fuzzy logic 模糊逻辑 intelligent agent 智能代理 electromagnetic adj 电磁的 coaxial adj 同轴的,共轴的 microwave n 微波 charge v充电,使充电 insulator n 绝缘体,绝缘物 nonconductive adj非导体的,绝缘的 antenna n天线;触角 modeling n建模,造型 simulation n 仿真;模拟 prototype n 原型 array n 排队,编队 vector n 向量,矢量 wavelet n 微波,小浪 sine 正弦cosine 余弦 inverse adj倒转的,反转的n反面;相反v 倒转 high-performance 高精确性,高性能 two-dimensional 二维的;缺乏深度的 three-dimensional 三维的;立体的;真实的 object-oriented programming面向对象的程序 设计 spectral adj 光谱的 attenuation n衰减;变薄;稀释 distortion n 失真,扭曲,变形 wavelength n 波长 refractive adj 折射的 ATM 异步传输模式Asynchronous Transfer Mode ADSL非对称用户数字线Asymmetric digital subscriber line VDSL甚高速数字用户线very high data rate digital subscriber line HDSL高速数据用户线high rate digital subscriber line FDMA频分多址(Frequency Division Multiple Access) TDMA时分多址(Time Division Multiple Access) CDMA同步码分多址方式(Code Division Multiple Access) WCDMA宽带码分多址移动通信系统(Wideband Code Division Multiple Access) TD-SCDMA(Time Division Synchronous Code Division Multiple Access)时分同步码分多址 SDLC(synchronous data link control)同步数据 链路控制 HDLC(high-level data link control)高级数据链路 控制 IP/TCP(internet protocol /transfer Control Protocol)网络传输控制协议 ITU (International Telecommunication Union) 国际电信联盟 ISO国际标准化组织(International Standardization Organization); OSI开放式系统互联参考模型(Open System Interconnect) GSM全球移动通信系统(Global System for Mobile Communications) GPRS通用分组无线业务(General Packet Radio Service) FDD(frequency division duplex)频分双工 TDD(time division duplex)时分双工 VPI虚路径标识符(Virtual Path Identifier); ISDN(Integrated Services Digital Network)综 合业务数字网 IDN综合数字网(integrated digital network) HDTV (high definition television)高清晰度电视 DCT(Discrete Cosine Transform)离散余弦变换 VCI(virtual circuit address)虚通路标识 MAN城域网Metropolitan area networks LAN局域网local area network WAN广域网wide area network 同步时分复用STDM Synchronous Time Division Multiplexing 统计时分复用STDM Statistical Time Division Multiplexing 单工传输simplex transmission 半双工传输half-duplex transmission 全双工传输full-duplex transmission 交换矩阵Switching Matrix 电路交换circuit switching 分组交换packet switching 报文交换message switching 奇偶校验parity checking 循环冗余校验CRC Cyclic Redundancy Check 虚过滤Virtual filter 数字滤波digital filtering 伪随机比特Quasi Random Bit 带宽分配Bandwidth allocation 信源information source 信宿destination 数字化digitalize 数字传输技术Digital transmission technology 灰度图像Grey scale images 灰度级Grey scale level 幅度谱Magnitude spectrum 相位谱Phase spectrum 频谱frequency spectrum 智能设备Smart Device 软切换Soft handover 硬切换Hard Handover 相干检测Coherent detection 边缘检测Edge detection 冲突检测collision detection 业务集合service integration 业务分离/综合service separation/ integration 网络集合network integration 环形网Ring networks 令牌环网Token Ring network 网络终端Network Terminal 用户终端user terminal 用户电路line circuit 电路利用率channel utilization(通道利用率) 相关性coherence 相干解调coherent demodulation 数字图像压缩digital image compression 图像编码image encoding 有损/无损压缩lossy/lossless compression 解压decompression 呼叫控制Call Control 误差控制error control 存储程序控制stored program control 存储转发方式store-and-forward manner 语音\视频传输voice\video transmission 视频点播video-on-demand(VOD) 会议电视Video Conference 有线电视cable television 量化quantization 吞吐量throughput 话务量traffic 多径分集Multipath diversity 多媒体通信MDM Multimedia Communication 多址干扰Multiple Access Interference 人机交互man machine interface 交互式会话Conversational interaction
从事质量工作以来积累的常用英语,希望对有需要的朋友有所帮助!质量专业英语大全零件材料类的专有名词 CPU: central processing unit(中央处理器) IC: Integrated circuit(集成电路) Memory IC: Memory Integrated circuit(记忆集成电路) RAM: Random Access Memory(随机存取内存) DRAM: Dynamic Random Access Memory(动态随机存取内存)SRAM: Staic Random Access Memory(静态随机内存) ROM: Read-only Memory(只读存储器) EPROM:Electrical Programmable Read-only Memory (电可抹只读存诸器) EEPROM: Electrical Erasbale Programmable Read-only Memory(电可抹可编程只读存储器) CMOS: Complementary Metal-Oxide-Semiconductor (互补金属氧化物半导体) BIOS: Basic Input Output System(基本输入输出系统)Transistor:晶体管 LED:发光二极管 Resistor:电阻 Variator:可变电阻
Capacitor:电容 Capacitor array:排容Diode:二极管 Transistor:三极体Transformer:变压器(ADP)Oscillator:频率振荡器(0sc)Crystal:石英振荡器 XTAL/OSC:振荡产生器(X)Relay:延时器 Sensor:感应器 Bead core:磁珠 Filter:滤波器 Flat Cable:排线 Inductor:电感 Buzzer:蜂鸣器 Socket:插座 Slot:插槽 Fuse:熔断器 Current:电流表 Solder iron:电烙铁Magnifying glass:放大镜Caliper:游标卡尺
常用词汇 主厂房main power building 设备缺陷equipment defect 缺陷处理defect treatment 设备规范Specification of equipment 铭牌nameplate 接线盒terminal box 热网heating network 电网network 供货范围scope of supply 参数parameter 停机, 停运outage 皮带速度belt velocity 皮带传输belt conveyor 蒸汽参数steam condition 蒸发量generation rates 功率因素power factor 输出负荷continuous rating output 额定蒸汽流量Max. continuous rating(MCR) 额定电压rated voltage 额定电流rated current 运行工况operation condition 值班员attendant 工日man-day 工时man-hour 事故甩负荷emergency load dump 四班三倒three shift by four teams 白班day shift 长白班regular shift 小休short-time off 大休long time-off 行灯safety lamp, 手锤hand hammer, 钢丝reinforcing wire 螺丝刀screw driver 测厚仪pachometer, 电筒electric torch 卡尺Sliding caliper 撬棒crowbar 手拉葫芦hand chain block 梯子Ladder, 扳手spanner 安全帽safety helmet 手套gloves 分包商sub-contractor 承包商contractor 土建civil work 工作票work order 操作票operation order
工廠常用英語翻譯(機械、模具) 总经理办公室General manager’s office 模具部Tooling department 项目部Project department品质部Quality department计划 部 Plan department 制造部Manufacture department产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 计划 科 Plan section 仓务科 Warehouse section商务科 Business section品质规划科 quality plan section IQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center 项目规划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section 设备科 Facility section采购科 Purchase section综合办 General affairs office 编程科 Programming section 模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop 总经理General manager (GM)经理managerXX部门经理Manager of XX department 原料库 Raw material warehouse半成品库 Semi-finished product warehouse成品库 Finished product warehouse科长 section chief 主任 chief 部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary 文员clerk操作员operator助理assistant职员staff 陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock 数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing 投影projection视图view 剖视图profile chart 标准件standard component零件图part drawing 装配图assembly drawing尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material刚度准则rigidity criterion 垫圈washer 垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint曲柄crank摇杆racker凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient求导derivation 定积分definite integral不定积分indefinite integral 曲率curvature偏微分partial differential 毛坯rough游标卡尺slide caliper千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations 概率probability 随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss轴线axes余子式cofactor
一:常用术语 Hon Hai 鸿海 CMM Component module move 机动元件整合 CEM Contract Manu faction service 合约委托代工 IBSC Internet Business Solution Center 国际互联网应用中心 PCEG Personal Computer Enclosure group 个人计算机外设事业群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鸿富锦事业群 SABG system assembly business group 系统组装事业群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鸿准 Stamping tool shop I 冲模一厂 Stamping tool shop II 冲模二厂 Prototype workshop 样品中心 Steel factory 裁剪厂 PCE molding tooling workshop PCE塑模厂 Hua Nan test and measurement center 华南检测中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 镁合金 Engineer standard 工标 Document center (database center)资料中心 Design Center 设计中心 Painting 烤漆(厂) Assembly组装(厂) Stamping 冲压(厂) Education and Training教育训练 proposal improvement/creative suggestion提案改善 Technological exchange and study 技术交流研习会 Technology and Development Committee 技术发展委员会 BS Brain Storming 脑力激荡 QCC Quality Control Circle 质量圈 PDCA Plan Do Check Action 计划执行检查总结 DCC delivery control center 交货管制中心 3C Computer 计算机类产品 Consumer electronics 消费性电子产品 Communication 通讯类产品 Core value(核心价值) Love 爱心
电子信息工程专业英语(A) 1.resistor n.电阻 2. diode n.二极管 3. ohm n.欧姆 4.tolerance ['t?l?r?ns] n.容限,公差,允许误差。5 decimal ['desim?l]十进位的,小数的 6 ratings 额定值7capacitor [k?'p?sit?] 电容器8 parallel 并行的 9 capacitance 电容量10 coefficients 系数11conduct 导体 12 charge n 电荷、v充电13 soldering 焊接、锡焊、低温焊接 14. first order system 一阶系统15. transient response 暂态响应 16. circuit 电路17. inductor 电感器18. inductance 电感,感应系数19.tune v.调谐20 vacuum ['v?kju?m真空,空间,真空吸尘器21.induce 感应22. magnetic field 磁场23.semiconductor 半导体24 silicon 硅25. relay 继电器26.electorn 电子27.infrared [,infr?'red 红外线的28. zener diode 稳压二极管,齐纳二极管29.rectifier diode 整流二极管30.alternating current 交流电流31.direct current 直流电流32.integrated circuit 集成电路33.voltage regulator 稳压器,电压调节器34.valence band 价(电子)带35 transistor 晶体管
1.机械与工厂英语 组装、冲压、喷漆等专业词汇Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条形码 barcode scanner条形码扫描仪fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查thumb screw大头螺丝 lbs.inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis |'∫?si| 基座bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试V oltage switch of SPS 电源电压接柆键 sheet metal parts 冲件 plastic parts塑料件 SOP制造作业程序 material check list物料检查表work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门planning department企划部 QC Section品管科 stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein |刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割
1.QC : quality control 品质管制 2.IQC : incoming quality control 进料品质管制 3.OQC : output quality control 出货品质管制 4.PQC : process quality control 制程品质管制也称IPQC : in process quality control . 5 AQL : acceptable quality level 允收标准 6.CQA: customer quality assurance 客户品质保证 7.MD : major defeat 主要缺点 8. MI : minor defeat 次要缺点 9. CR :critical defeat 关踺缺点 10. SMT : surface mounting technology 表面粘贴技术 11 . SMD : surface mounting device SMC : surface mounting component 表面粘贴元件 12 . ECN : engineering change notice 工程变更通知 13 . DCN : design change notice 设计变更通知 14 . PCB : printed circuit board 印刷电路板 15 . PCBA : printed circuit board assembly装配印刷电路板 16 . BOM : bill of material 材料清单 17. BIOS : basically input and output system 基本输入输出系统 18. MIL-STD-105E : 美国陆军标准,也称单次抽样计划. 19 . ISO : international standard organization 国际标准化组织 20 . DRAM: 内存条 21 . Polarity : 极性 22 . Icicles : 锡尖 23 . Non-wetting : 空焊 24 . Short circuit : 短路 25 . Missing component : 缺件 26 . Wrong component : 错件 27 . Excess component : 多件 28 . Insufficient solder : 锡少 29 . Excessive solder : 锡多 30 . Solder residue : 锡渣 31 . Solder ball : 锡球 32 . Tombstone : 墓碑 33 . Sideward : 侧立 34 . Component damage : 零件破损 35 . Gold finger : 金手指 36 . SOP : standard operation process 标准操作流程 37 . SIP : standard inspection process 标准检验流程 38 . The good and not good segregation :良品和不良品区分 39 . OBW : on board writer 熸录BIOS 40 . Simple random sampling : 简单随机抽样 41 . Histogram : 直方图