LED照明专业术语中英文对照
1 backplane 背板
2 Band gap voltage reference 带隙电压参考
3 benchtop supply 工作台电源
4 Block Diagram 方块图
5 Bode Plot 波特图
6 Bootstrap 自举
7 Bottom FET Bottom FET
8 bucket capcitor 桶形电容
9 chassis 机架
10 Combi-sense Combi-sense
11 constant current source 恒流源
12 Core Sataration 铁芯饱和
13 crossover frequency 交叉频率
14 current ripple 纹波电流
15 Cycle by Cycle 逐周期
16 cycle skipping 周期跳步
17 Dead Time 死区时间
18 DIE Temperature 核心温度
19 Disable 非使能,无效,禁用,关断
20 dominant pole 主极点
21 Enable 使能,有效,启用
22 ESD Rating ESD额定值
23 Evaluation Board 评估板
24 Exceeding the specifications below may result in perman ent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characte ristics section is not implied.
超过下面的规格使用可能引起永久的设备损害或设备故障。建议不要工作在电特性表规定的参数范围以外。
25 Failling edge 下降沿
26 figure of merit 品质因数
27 float charge voltage 浮充电压
28 flyback power stage 反驰式功率级
29 forward voltage drop 前向压降
30 free-running 自由运行
31 Freewheel diode 续流二极管
32 Full load 满负载33 gate drive 栅极驱动
34 gate drive stage 栅极驱动级
35 gerber plot Gerber 图
36 ground plane 接地层
37 Henry 电感单位:亨利
38 Human Body Model 人体模式
39 Hysteresis 滞回
40 inrush current 涌入电流
41 Inverting 反相
42 jittery 抖动
43 Junction 结点
44 Kelvin connection 开尔文连接
45 Lead Frame 引脚框架46 Lead Free 无铅
47 level-shift 电平移动
48 Line regulation 电源调整率
49 load regulation 负载调整率
50 Lot Number 批号
51 Low Dropout 低压差
52 Miller 密勒53 node 节点
54 Non-Inverting 非反相
55 novel 新颖的
56 off state 关断状态
57 Operating supply voltage 电源工作电压
58 out drive stage 输出驱动级
59 Out of Phase 异相
60 Part Number 产品型号
61 pass transistor pass transistor
62 P-channel MOSFET P沟道MOSFET
63 Phase margin 相位裕度
64 Phase Node 开关节点
65 portable electronics 便携式电子设备
66 power down 掉电
67 Power Good 电源正常
68 Power Groud 功率地
69 Power Save Mode 节电模式
70 Power up 上电
71 pull down 下拉
72 pull up 上拉
73 Pulse by Pulse 逐脉冲(Pulse by Pulse)
74 push pull converter 推挽转换器
75 ramp down 斜降
76 ramp up 斜升
77 redundant diode 冗余二极管
78 resistive divider 电阻分压器
79 ringing 振铃
80 ripple current 纹波电流
81 rising edge 上升沿
82 sense resistor 检测电阻
83 Sequenced Power Supplys 序列电源
84 shoot-through 直通,同时导通
85 stray inductances. 杂散电感
86 sub-circuit 子电路
87 substrate 基板
88 Telecom 电信
89 Thermal Information 热性能信息
90 thermal slug 散热片
91 Threshold 阈值
92 timing resistor 振荡电阻
93 Top FET Top FET
94 Trace 线路,走线,引线
95 Transfer function 传递函数
96 Trip Point 跳变点
97 turns ratio 匝数比,=Np / Ns。(初级匝数/次级匝数)
98 Under Voltage Lock Out (UVLO) 欠压锁定
99 Voltage Reference 电压参考
100 voltage-second product 伏秒积
101 zero-pole frequency compensation 零极点频率补偿102 beat frequency 拍频
103 one shots 单击电路
104 scaling 缩放
105 ESR 等效串联电阻[Page]
106 Ground 地电位
107 trimmed bandgap 平衡带隙
108 dropout voltage 压差
109 large bulk capacitance 大容量电容
110 circuit breaker 断路器
111 charge pump 电荷泵
112 overshoot 过冲
印制电路printed circuit
印制线路printed wiring
印制板printed board
印制板电路printed circuit board
印制线路板printed wiring board
印制元件printed component
印制接点printed contact
印制板装配printed board assembly
板board
刚性印制板rigid printed board
挠性印制电路flexible printed circuit
挠性印制线路flexible printed wiring
齐平印制板flush printed board
金属芯印制板metal core printed board
金属基印制板metal base printed board
多重布线印制板mulit-wiring printed board
塑电路板molded circuit board
散线印制板discrete wiring board
微线印制板micro wire board
积层印制板buile-up printed board
表面层合电路板surface laminar circuit
埋入凸块连印制板B2it printed board
载芯片板chip on board
埋电阻板buried resistance board
母板mother board
子板daughter board
背板backplane
裸板bare board
键盘板夹心板copper-invar-copper board
动态挠性板dynamic flex board
静态挠性板static flex board 可断拼板break-away planel
电缆cable
挠性扁平电缆flexible flat cable (FFC)
薄膜开关membrane switch
混合电路hybrid circuit
厚膜thick film
厚膜电路thick film circuit
薄膜thin film
薄膜混合电路thin film hybrid circuit
互连interconnection
导线conductor trace line
齐平导线flush conductor
传输线transmission line
跨交crossover
板边插头edge-board contact
增强板stiffener
基底substrate
基板面real estate
导线面conductor side
元件面component side
焊接面solder side
导电图形conductive pattern
非导电图形non-conductive pattern
基材base material
层压板laminate
覆金属箔基材metal-clad bade material
覆铜箔层压板copper-clad laminate (CCL) 复合层压板composite laminate
薄层压板thin laminate
基体材料basis material
预浸材料prepreg
粘结片bonding sheet
预浸粘结片preimpregnated bonding sheer 环氧玻璃基板epoxy glass substrate
预制内层覆箔板mass lamination panel
内层芯板core material
粘结层bonding layer
粘结膜film adhesive
无支撑胶粘剂膜unsupported adhesive film 覆盖层cover layer (cover lay)
增强板材stiffener material
铜箔面copper-clad surface
去铜箔面foil removal surface
层压板面unclad laminate surface
基膜面base film surface
胶粘剂面adhesive faec
原始光洁面plate finish
粗面matt finish
剪切板cut to size panel
超薄型层压板ultra thin laminate
A阶树脂A-stage resin
B阶树脂B-stage resin
C阶树脂C-stage resin
环氧树脂epoxy resin
酚醛树脂phenolic resin
聚酯树脂polyester resin
聚酰亚胺树脂polyimide resin
双马来酰亚胺三嗪树脂bismaleimide-triazine resin 丙烯酸树脂acrylic resin
三聚氰胺甲醛树脂melamine formaldehyde resin 多官能环氧树脂polyfunctional epoxy resin
溴化环氧树脂brominated epoxy resin
环氧酚醛epoxy novolac
氟树脂fluroresin
硅树脂silicone resin
硅烷silane
聚合物polymer
无定形聚合物amorphous polymer
结晶现象crystalline polamer
双晶现象dimorphism
共聚物copolymer
合成树脂synthetic
热固性树脂thermosetting resin [Page]
热塑性树脂thermoplastic resin
感光性树脂photosensitive resin
环氧值epoxy value
双氰胺dicyandiamide
粘结剂binder
胶粘剂adesive
固化剂curing agent
阻燃剂flame retardant
遮光剂opaquer
增塑剂plasticizers
不饱和聚酯unsatuiated polyester
聚酯薄膜polyester
聚酰亚胺薄膜polyimide film (PI)
聚四氟乙烯polytetrafluoetylene (PTFE)
增强材料reinforcing material
折痕crease
云织waviness
鱼眼fish eye
毛圈长feather length
厚薄段mark
裂缝split
捻度twist of yarn
浸润剂含量size content
浸润剂残留量size residue
处理剂含量finish level
偶联剂couplint agent
断裂长breaking length 吸水高度height of capillary rise
湿强度保留率wet strength retention
白度whitenness
导电箔conductive foil
铜箔copper foil
压延铜箔rolled copper foil
光面shiny side
粗糙面matte side
处理面treated side
防锈处理stain proofing
双面处理铜箔double treated foil
模拟simulation
逻辑模拟logic simulation
电路模拟circit simulation
时序模拟timing simulation
模块化modularization
设计原点design origin
优化(设计)optimization (design)
供设计优化坐标轴predominant axis
表格原点table origin
元件安置component positioning
比例因子scaling factor
扫描填充scan filling
矩形填充rectangle filling
填充域region filling
实体设计physical design
逻辑设计logic design
逻辑电路logic circuit
层次设计hierarchical design
自顶向下设计top-down design
自底向上设计bottom-up design
费用矩阵cost metrix
元件密度component density
自由度degrees freedom
出度out going degree
入度incoming degree
曼哈顿距离manhatton distance
欧几里德距离euclidean distance
网络network
阵列array
段segment
逻辑logic
逻辑设计自动化logic design automation 分线separated time
分层separated layer
定顺序definite sequence
导线(通道)conduction (track)
导线(体)宽度conductor width
导线距离conductor spacing
导线层conductor layer
导线宽度/间距conductor line/space
第一导线层conductor layer No.1
圆形盘round pad
方形盘square pad
菱形盘diamond pad
长方形焊盘oblong pad
子弹形盘bullet pad
泪滴盘teardrop pad
雪人盘snowman pad
形盘V-shaped pad V
环形盘annular pad
非圆形盘non-circular pad
隔离盘isolation pad
非功能连接盘monfunctional pad
偏置连接盘offset land
腹(背)裸盘back-bard land
盘址anchoring spaur
连接盘图形land pattern
连接盘网格阵列land grid array
孔环annular ring
元件孔component hole
安装孔mounting hole
支撑孔supported hole
非支撑孔unsupported hole
导通孔via
镀通孔plated through hole (PTH)
余隙孔access hole
盲孔blind via (hole)
埋孔buried via hole
埋,盲孔buried blind via
任意层内部导通孔any layer inner via hole
全部钻孔all drilled hole
定位孔toaling hole
无连接盘孔landless hole
中间孔interstitial hole
无连接盘导通孔landless via hole
引导孔pilot hole
端接全隙孔terminal clearomee hole
准尺寸孔dimensioned hole [Page]
在连接盘中导通孔via-in-pad
孔位hole location
孔密度hole density
孔图hole pattern
钻孔图drill drawing
装配图assembly drawing
参考基准datum referan
1)元件设备
三绕组变压器:three-column transformer ThrClnTrans
双绕组变压器:double-column transformer DblClmnTrans 电容器:Capacitor
并联电容器:shunt capacitor
电抗器:Reactor
母线:Busbar
输电线:TransmissionLine
发电厂:power plant
断路器:Breaker
刀闸(隔离开关):Isolator
分接头:tap
电动机:motor
(2)状态参数
有功:active power
无功:reactive power
电流:current
容量:capacity
电压:voltage
档位:tap position
有功损耗:reactive loss
无功损耗:active loss
功率因数:power-factor
功率:power
功角:power-angle
电压等级:voltage grade
空载损耗:no-load loss
铁损:iron loss
铜损:copper loss
空载电流:no-load current
阻抗:impedance
正序阻抗:positive sequence impedance 负序阻抗:negative sequence impedance 零序阻抗:zero sequence impedance
电阻:resistor
电抗:reactance
电导:conductance
电纳:susceptance
无功负载:reactive load 或者QLoad
有功负载: active load PLoad
遥测:YC(telemetering)
遥信:YX
励磁电流(转子电流):magnetizing current 定子:stator
功角:power-angle
上限:upper limit
下限:lower limit
并列的:apposable
高压: high voltage
低压:low voltage
中压:middle voltage
电力系统power system
发电机generator
励磁excitation
励磁器excitor
电压voltage
电流current
母线bus
变压器transformer
升压变压器step-up transformer
高压侧high side
输电系统power transmission system
输电线transmission line
固定串联电容补偿fixed series capacitor compensation 稳定stability
电压稳定voltage stability
功角稳定angle stability
暂态稳定transient stability
电厂power plant
能量输送power transfer
交流AC
装机容量installed capacity
电网power system
落点drop point
开关站switch station
双回同杆并架double-circuit lines on the same tower 变电站transformer substation
补偿度degree of compensation
高抗high voltage shunt reactor
无功补偿reactive power compensation
故障fault
调节regulation
裕度magin
三相故障three phase fault
故障切除时间fault clearing time
极限切除时间critical clearing time
切机generator triping
高顶值high limited value
强行励磁reinforced excitation 线路补偿器LDC(line drop compensation)
机端generator terminal
静态static (state)
动态dynamic (state)
单机无穷大系统one machine - infinity bus system 机端电压控制AVR
电抗reactance
电阻resistance
功角power angle
有功(功率)active power
无功(功率)reactive power
功率因数power factor
无功电流reactive current
下降特性droop characteristics
斜率slope
额定rating
变比ratio
参考值reference value
电压互感器PT
分接头tap
下降率droop rate
仿真分析simulation analysis
传递函数transfer function
框图block diagram
受端receive-side
裕度margin
同步synchronization
失去同步loss of synchronization
阻尼damping
摇摆swing
保护断路器circuit breaker
电阻:resistance
电抗:reactance
阻抗:impedance
电导:conductance
电纳:susceptance
财务专业术语中英文对照表 英文中文说明 Account Accounting system 会计系统 American Accounting Association 美国会计协会 American Institute of CPAs 美国注册会计师协会 Audit 审计 Balance sheet 资产负债表 Bookkeepking 簿记 Cash flow prospects 现金流量预测 Certificate in Internal Auditing 部审计证书 Certificate in Management Accounting 管理会计证书 Certificate Public Accountant注册会计师 Cost accounting 成本会计 External users 外部使用者 Financial accounting 财务会计 Financial Accounting Standards Board 财务会计准则委员会 Financial forecast 财务预测 Generally accepted accounting principles 公认会计原则 General-purpose information 通用目的信息 Government Accounting Office 政府会计办公室 Income statement 损益表 Institute of Internal Auditors 部审计师协会 Institute of Management Accountants 管理会计师协会 Integrity 整合性 Internal auditing 部审计 Internal control structure 部控制结构 Internal Revenue Service 国收入署 Internal users部使用者 Management accounting 管理会计 Return of investment 投资回报 Return on investment 投资报酬 Securities and Exchange Commission 证券交易委员会
品质名词(中英对照)A ABC analysis ABC 分析 Abnormality 不正常性 Abscissa 横坐标 Absolute deviation 绝对离差 Absolute dispersion 绝对离势 Absolute error 绝对误差 Absolute frequency 绝对次数 Absolute number 绝对数 Absolute reliability 绝对可靠度 Absolute term 绝对项 Absolute value 绝对值 Absolute variation 绝对变异 Abstract number 抽象数 Abstract unit 抽象单位 Accelerated factor 加速系数,加速因子Accelerated life test 加速寿命试验
Accelerated test 加速试验 Acceleration 加速度 Acceptable limit 允收界限 Acceptable process 允收制程水平Acceptable quality 允收品质 Acceptable quality level (AQL) 允收质量水平Acceptable reliability level (ARL) 允收可靠度水平Acceptability 允收性 Acceptability criterion 允收标准 Acceptance 允收,验收 Acceptance, probability of 允收机率Acceptance, region of 允收区域 Acceptance and rejection criteria 允收与拒收准则Acceptance boundary 允收界限 Acceptance coefficient 允收系数 Acceptance control chart 验收管制图Acceptance cost 验收费用 Acceptance criteria 允收准则Acceptance error 允收误差
Chemntherapeutic agents 化学疗法 thus xue fiao fa) Chemothcrjipy 化学疔,Z (hija xue Aaa fa) hns the goal of killing or stopping rhe development nf rapidly dividing cells. Examples are Cisplatin, Carboplat in, Bkomycin I 博来霉嗪1 (ftd l3f Sg S-fltinrncjrao 5 氟尿瞪喘(ft/ HiAO m dfinfl), mrthotrExate 甲員媒时{Jia 的 did /ioffk Vincristine fifr chun xJTj/a^, Vinblastine 衣祚碱 (chang chun ;ian}. Taxol and Tawiuvirtn .木戟题(SSfi ben 阳ng 钠* Since the sanK nicchanism (hat kilh malignant cdl or blocks de vela pment of a malignant cell cm have similar effects on a nnrnuil, rap idly dividing celt any of LhcNt agents ciin hax r c btid side clfccts. Some terms of cancer ircitLcd with chemcthera 卩、may cjus,e ihe cancer (o "disappear
常用中英文对照 MSA:测量系统分析(MEASUREMENT SYSTEM ANALYSIS) AQL:允收水准(ACCEPTABLE QUALITY LEVER) ISO:国际标准化组织(INTERNATIONAL ORGANIZATION FOR STANGDARDIZA TION)FMEA:失效模式和影响分析(FAILURE MODE AND EFFECT ANALYSIS) FPY:首次合格率(FIRST PASS YIELD) JIT:及时率(JUST IN TIME) QC:品质控制 QA:品质保证 QE:品质工程 IQC:来料品质控制(INCOMING QUALITY CONTROL) IPQC:制程品质控制(INPROCESS ----------------------------) FQC:最终品质控制(FINAL -------------------------------------) LQC:生产线品质控制(LINE --------------------------------------) SQA:供应商品质保证(SUPPLIER QUALITY CONTROL) DCC:文控中心(DOCUMENT CONTROL CENTER) PQA:制程品质保证(PROCESS QUALITY ASSYRANCE) FQA:最终-------------(FINAL ---------------------------------------) DAS:缺陷分析系统(DEFECTS ANALYSIS SYSTEM) FA:坏品分析(FAILURE ANALYSIS) CPI:连续工序改善(CONTINUOUS PROCESS IMPROVEMENT) CS:客户服务(CUSTEMER SERVICE) TRAINING:培训 COQ:品质成本 COIF:内部缺陷成本 PPM:百万分之-----(PART PER MILLION) MSDS:材料安全资料卡(MATERIAL SAFETY DATA SHEET) MRB:物料/材料审查委员会(MATERIALS REVIEW BOARD) MQC:制造质量控制(MANUFACTURING QUALITY CONTORL) QAP:质量保证计划(QUALITY ASSURANCE PLANNING) BOM:料件结构表(BILLS OF MATERIAL) QM:品质手册(QUALITY MANUAL) QP:品质程序(QUALITY PROCEDURE/PEOGRAM) WI:作业指导书(SOP/SIP------WORK INSTRUCTION) FR:表单/表格(FORM) SOP:标准操作程序(STANDARD OPERATING PROCEDURE) SIP:标准检验程序(STANDARD INSPECTION PROCEDURE) FIFO:先进先出(FIRST IN FIRST OUT) CO:公司(COMPANY) LID:有限的(LIMITED) CC:复写的副本;抄送(CARBON COPY)
照明基本的专业英文词汇 ambipolar diffusion\[物]双极扩散 arc discharge\电弧放电, 弧光放电 avalanche\n.雪崩\v.雪崩 buffer gas\缓冲气体 candle\n.蜡烛vt.对着光检查 cap\灯座 charge neutrality\电中性区 chromaticity diagram色度图 coiled coil\卷曲螺旋 colorimetry\色度学 Columnar cell\柱状细胞 compact fluorescent lamp\紧凑型荧光灯 cone cell\视锥细胞, 圆锥细胞 critical angle\n.[物][空]临界角 carbon arc lamp\炭弧灯 diffuse\v.散播, 传播, 漫射, 扩散, (使)慢慢混合\adj.散开的, 弥漫的 diffuse reflection\漫反射 diffuse transmission\扩散透射\ 漫透射\ 扩散传输 diffusion\n.扩散, 传播, 漫射 double helix\二重螺旋线, 双螺旋线
electroluminescent lamp\场致发光灯 electrode\n.电极 electroluminescence\n. [物]场致发光, 电致发光electromagnetic radiation\电磁辐射electromagnetic wave\n.[电磁]电磁波 envelope\玻壳 filament\n.细丝, 灯丝 filter\n.滤波器, 过滤器, 滤光器, 筛选fluorescent lamp\n.荧光灯(管),日光灯(管) full radiator\完全辐射体 fuse\n.保险丝, 熔丝\v.熔合 gas incandescent lamp\充气白炽灯 gas-filled lamp\充气灯 getter\消气剂 glass pinch\玻璃封接 glow discharge\辉光放电 high pressure mercury lamp\高压汞灯 high pressure xenon lamp\高压氙灯homogeneous light\单色光 illuminance\n.(=illumination)照明[度], 启发Incandescent lamp\白炽灯, 白热灯 incidence\n.]入射
银行英语: 出口信贷 export credit 出口津贴 export subsidy 商品倾销 dumping 外汇倾销 exchange dumping 优惠关税 special preferences 保税仓库 bonded warehouse 贸易顺差 favorable balance of trade 贸易逆差 unfavorable balance of trade 进口配额制 import quotas 自由贸易区 free trade zone 对外贸易值 value of foreign trade 国际贸易值 value of international trade 普遍优惠制 generalized system of preferences-GSP 最惠国待遇 most-favored nation treatment-MFNT -------------------价格条件 ---------------------- 价格术语trade term (price term) 运费freight 单价 price 码头费wharfage 总值 total value 卸货费landing charges 金额 amount 关税customs duty 净价 net price 印花税stamp duty 含佣价price including commission 港口税portdues 回佣return commission 装运港portof shipment 折扣discount,allowance 卸货港port of discharge 批发价 wholesale price 目的港portof destination 零售价 retail price 进口许口证inportlicence 现货价格spot price 出口许口证exportlicence 期货价格forward price 现行价格(时价)current price prevailingprice 国际市场价格 world (International)Marketprice 离岸价(船上交货价)FOB-free on board 成本加运费价(离岸加运费价) C&F-cost and freight 到岸价(成本加运费、保险费价) CIF-cost,insurance and freight --------------------交货条件 ---------------------- 交货delivery 轮船steamship(缩写S.S) 装运、装船shipment 租船charter (the chartered shep) 交货时间 time of delivery
语文课程与教学论 名词术语中英文对照表 the Chinese Course and Teaching and Learning Theory in Chinese and English Teaching materials editing teaching materials /Chinese Teaching Materials /edit teaching materials /Uniformed Chinese Teaching Materials /Experimental Teaching Materials /Mother Tongue Teaching Materials /Teaching Materials of the New Course *textbook *reading book *teaching reference book *exercises book *studying plan Technology /Educational Technology /Modern Educational Technology /Educational Technology in Chinese Teaching /multi-media technology /net technology /cloud serving technology *white board *net meeting *chat room *blog Teaching Basic Theory of the Teaching teaching aim teaching task teaching objective teaching model teaching tactics teaching principle teaching program teaching reform teaching case Courseware teaching resources teaching experiment /mother tongue teaching A Term List of 1. 教材( JC ) 教材编写 /语文教材 /编写教材 / 统编教材 /实验教材 /母语教材 /新课程教材 * 课本 * 读本 * 教学参考书(教参) * 练习册 *学案 2. 技术( JS ) / 教育技术 /现代 教育技术 /语文 教育技术 /多媒 体技术 / 网络 技术 /云服务技 术 * 白板 *网 络会议 *聊天室 * 博克 3. 教学 (JX ) 教学基本理论 教学目的 教学 任务 教学目标 教学模式 教学 策略 教学原则 教学大纲 教学 改革 教学案例 教学课件 教学 资源 教学实验 /母语教学
LED照明专业术语中英文对照 1 backplane 背板 2 Band gap voltage reference 带隙电压参考 3 benchtop supply 工作台电源 4 Block Diagram 方块图 5 Bode Plot 波特图 6 Bootstrap 自举 7 Bottom FET Bottom FET 8 bucket capcitor 桶形电容 9 chassis 机架 10 Combi-sense Combi-sense 11 constant current source 恒流源 12 Core Sataration 铁芯饱和 13 crossover frequency 交叉频率 14 current ripple 纹波电流 15 Cycle by Cycle 逐周期 16 cycle skipping 周期跳步 17 Dead Time 死区时间 18 DIE Temperature 核心温度 19 Disable 非使能,无效,禁用,关断 20 dominant pole 主极点 21 Enable 使能,有效,启用 22 ESD Rating ESD额定值 23 Evaluation Board 评估板 24 Exceeding the specifications below may result in perman ent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characte ristics section is not implied. 超过下面的规格使用可能引起永久的设备损害或设备故障。建议不要工作在电特性表规定的参数范围以外。 25 Failling edge 下降沿 26 figure of merit 品质因数 27 float charge voltage 浮充电压 28 flyback power stage 反驰式功率级 29 forward voltage drop 前向压降 30 free-running 自由运行 31 Freewheel diode 续流二极管 32 Full load 满负载33 gate drive 栅极驱动 34 gate drive stage 栅极驱动级 35 gerber plot Gerber 图 36 ground plane 接地层 37 Henry 电感单位:亨利 38 Human Body Model 人体模式 39 Hysteresis 滞回 40 inrush current 涌入电流 41 Inverting 反相 42 jittery 抖动 43 Junction 结点 44 Kelvin connection 开尔文连接 45 Lead Frame 引脚框架46 Lead Free 无铅 47 level-shift 电平移动 48 Line regulation 电源调整率 49 load regulation 负载调整率 50 Lot Number 批号 51 Low Dropout 低压差 52 Miller 密勒53 node 节点 54 Non-Inverting 非反相 55 novel 新颖的 56 off state 关断状态 57 Operating supply voltage 电源工作电压 58 out drive stage 输出驱动级 59 Out of Phase 异相 60 Part Number 产品型号 61 pass transistor pass transistor 62 P-channel MOSFET P沟道MOSFET 63 Phase margin 相位裕度 64 Phase Node 开关节点 65 portable electronics 便携式电子设备 66 power down 掉电 67 Power Good 电源正常 68 Power Groud 功率地 69 Power Save Mode 节电模式 70 Power up 上电 71 pull down 下拉 72 pull up 上拉 73 Pulse by Pulse 逐脉冲(Pulse by Pulse) 74 push pull converter 推挽转换器 75 ramp down 斜降 76 ramp up 斜升 77 redundant diode 冗余二极管 78 resistive divider 电阻分压器 79 ringing 振铃 80 ripple current 纹波电流 81 rising edge 上升沿 82 sense resistor 检测电阻 83 Sequenced Power Supplys 序列电源 84 shoot-through 直通,同时导通 85 stray inductances. 杂散电感 86 sub-circuit 子电路 87 substrate 基板 88 Telecom 电信 89 Thermal Information 热性能信息 90 thermal slug 散热片 91 Threshold 阈值 92 timing resistor 振荡电阻 93 Top FET Top FET 94 Trace 线路,走线,引线
各种专业名称英语词汇中英文对照表
————————————————————————————————作者: ————————————————————————————————日期: ?
各种专业名称英语词汇中英文对照表 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学ChinesePhilosophy 外国哲学ForeignPhilosophies ?逻辑学Logic?伦理学Ethics 美学Aesthetics 宗教学Science of Religion?科学技术哲学Philosophy of Science andTechnology?经济学Economics?理论经济学Theoretical Economics ?政治经济学PoliticalEconomy ?经济思想史History ofEconomic Thought ?经济史History of Economic 西方经济学WesternEconomics?世界经济World Economics ?人口、资源与环境经济学Population,Resources andEnvironmentalEconomics 应用经济学Applied Economics 国民经济学National Economics?区域经济学Regional Economics ?财政学(含税收学)Public Finance (includingTaxation) 金融学(含保险学) Finance (including Insurance)?产业经济学Industrial Economics ?国际贸易学International Trade 劳动经济学Labor Economics ?统计学Statistics ?数量经济学Quantita tive Economics ?中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics?法学Law 法学Science of Law ?法学理论Jurisprudence?法律史Legal History ?宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence 民商法学(含劳动法学、社会保障法学)Civil Law and Commercial Law (i ncluding Science of LabourLawand Science ofSocial Sec urityLaw)?诉讼法学Science of ProcedureLaws ?经济法学Sc ience ofEconomic Law ?环境与资源保护法学Science ofEnvironment andNatural Resources Protection Law 国际法学(含国际公法学、国际私法学、国际经济法学、)Internationallaw (including International Public law, International PrivateLaw a
光通量luminous flux 光通量是指光源在单位时间里向周围空间辐射的,能引起视觉反应能量,即可见光的能量。它描述的是光源的有效辐射值,单位是1m(流明)。 同样功率的灯具的光通量可能完全不同,这是因为它们的光效不同的缘故。比如:普通照明灯泡只有10 1m/瓦,而金属卤素灯可以达到80 1m/瓦。 照度illuminance 照度是指在一个面上的光通密度,它是射入单位面积内的光通量,单位是Lx。 照度的定义和测量比较复杂,象平均柱面照度、等效球照度、标量照度等,它们的测量条件和计算方法有所不同。在建筑和装饰工程中经常会遇到、灯光系统中偶尔也涉及到照度概念。 发光强度luminous intensity 发光强度简称光强,国际单位是candela(坎德拉)简写cd。Lcd是指光源在指定方向的单位立体角内发出的光通量。 照明方式和种类例如: 1. 一般照明general lighting 2. 局部照明local lighting等 详细分类见《建筑照明术语标准》 电光源及其附件 例如: 1. 白炽灯incandescent lamp 2. 卤钨灯tungsten halogen lamp等 详细分类见《建筑照明术语标准》 灯具及其附件 例如: 1. 直接型灯具direct luminaire 2. 漫射型灯具diffused luminaire等 详细分类见《建筑照明术语标准》 采光技术例如: 1. 阳光;直射日光sunlight 2. 天空(漫射)光skylight等 详细分类见《建筑照明术语标准》 材料的光学特性和照明测量 例如: 1. 反射reflection 2. 透射transmisson 3. 漫射diffusion等 详细分类见《建筑照明术语标准》
1、the airframe 机身,结构 2、The front (fore) part 前部 3、The rear (aft) part 后部 4、port 左旋(舵) 5、starboard 右旋(舵) 6、the inboard engine or inboards 内侧发动机 7、the outboard engine or outboards 外侧发动机 8、the nose 机头 9、the belly 腹部 10、the skin 蒙皮 11、the windscreen or windshield 风挡 12、the wing 机翼 13、the trailing edge 机翼后缘 14、the leading edge 机翼前缘 15、the wing tip 翼尖 16、the control surface 操纵面 17、ailerons 副翼 18、flaps (inboard flap,outboard flap,leading edge flaps) 襟翼(内侧襟翼,外侧襟翼,前缘缝翼) 19、spoilers (inboard\outboard spoiler)(spoiler down\up) 阻力板,扰流板(内、外侧扰流板)(扰流板放下、打开) 20、slats 缝翼 21、elevators (elevator control tab) 升降舵(升降舵操纵片) 22、rudder (rudder control tab) 方向舵(方向舵操纵片)
23、flap angle 襟翼角 24、flap setting 襟翼调整 25、the full flap position 全襟翼位置 26、a flapless landing 无襟翼着陆 27、the landing gear 起落架 28、stabilizer 安定面 29、the nose wheel 前轮 30、gear locked 起落架锁定 31、the wheel well 起落架舱 32、the wheel door 起落架舱门 33、a tyre 轮胎 34、to burst 爆破 35、a deflated tyre 放了气的轮胎 36、a flat tyre 走了气的轮胎 37、a puncture 轮胎被扎破 38、to extend the flaps (to retract the flaps) 放下襟翼(收上襟翼) 39、gear extention (gear retraction) 起落架放下(起落架收上) 40、The gear is jammed. 起落架被卡死。 41、The flaps are jammed. 襟翼被卡死。 42、the emergency extention system 应急放下系统 43、to crank the gear down 摆动放下起落架 44、the brakes 刹车
Gredit Account货方科目 Exch Rate兑换率ASAP As soon As possible尽快 FTP File Transfer Protocol文件传递(输)协议CD-ROM compact disc read -only memory只读光盘存储器UV Ultraviolet紫外线 EC Engineering change工程变更 EV Equipment Variance量具变异 AV Appraiser variance作业者变异PV Part variation局部变异 Characteristic Diagram特性要因图 Stratification层别法 Check list查检表 Histogram直方图 Scatter Diagram散布图 Pare to Diagram柏拉图 Control Chart管制图 CEO Chief Executive Officer执行总裁 VIP Very Important Person贵宾 ERP Enterprice Resource Planning企业资源规划MRP I Material Requirement Planning物料需求规划MRP II Maufacturing Resource Planning制造资源规划OA Operation Analysis作业者变异 Gap Analysis差异分析PC Product Control生产分析 MC Material control物料管控 MTS make to--Stock存货式生产ATO assemble-to-order接单式装配ATM Applicotion Implementation应用系统导入方法 Unorder Receipt无订单的收料 Shop floor车间、职场 Shop floor control厂地控制、车间管理Shop floor production control工厂生产管理 Write书写 Observed观察 Read阅读 Listen听 UCL Upper Control Limit管制上限 LCL Lower Control Limit管制下限 Critical defect严重缺点 Minor defect次要缺点 Packing List出货明细 PCB Printed Circuit Board印刷电路板 PCBA Printed Circuit Board Assemblies 印刷电路板总成常用品质术语中英文对照表
常见照明灯具英语词汇常见照明灯具英语词汇 照明灯饰灯具分类英语词汇 室内灯 residential lamp / light 枝状大吊灯 chandeliers 吊灯 pendant lamp / light 半吊灯 half pendant lamp / light 台灯table lamp / light 壁灯wall lamp / light 孙光辉 Jacky Sun 落地灯 floor lamp / light 吸顶灯 ceiling lamp / light 水晶灯 crystal lamp / light 木灯wooden lamp / light 宫灯palace lamp / light 仿水晶灯 imitated crystal lamp / light 低压灯 low voltage lamp / light 工艺灯 artificial lamp / light 石艺灯 marble lamp / light 羊皮灯 parchment lamp / light 镜前灯 mirror front lamp / light 镜画灯 picture lamp / light 吊线灯 track / line lamp / light 格栅灯 grille lamp / light 水珠灯 water pearl lamp / light 导轨灯 track lamp / light 柱灯pillar lamp / light 蒂凡尼灯 tiffany lamp / light 风水灯 water fountain lamp / light 户外灯 outdoor lamp / light 路灯street lamp / light 筒灯down lamp / light 投光射灯 spot lamp / light 翻译整理 Translated by 孙光辉 Jacky Sun 庭院灯 garden lamp / light 草坪灯 lawn lamp / light 草地灯 lawn lamp / light 防水灯 water proof lamp / Under water lamp 柱头灯 water jet lamp / light 水底灯 underwater lamp / light 户外壁灯 outdoor wall lamp / light
术语表 Acceptance Criteria–接受标准:接受测试结果的数字限度、范围或其他合适的量度标准。Active Pharmaceutical Ingredient(API)(or Drug Substance)-活性要用成分(原料药)旨在用于药品制造中的任何一种物质或物质的混合物,而且在用于制药时,成为药品的一种活性成分。此种物质在疾病的诊断,治疗,症状缓解,处理或疾病的预防中有药理活性或其他直接作用,或者能影响机体的功能和结构。 API Starting Material–原料药的起始物料:用在原料药生产中的,以主要结构单元被并入该原料药的原料、中间体或原料药。原料药的起始物料可能是在市场上有售,能够根据合同或商业协议从一个或多个供应商处购得,或者自己生产。原料药的起始物料通常有特定的化学特性和结构。 Batch(or Lot)-批:有一个或一系列工艺过程生产的一定数量的物料,因此在规定的限度内是均一的。在连续生产中,一批可能对应与生产的某以特定部分。其批量可规定为一个固定数量,或在固定时间间隔内生产的数量。 Batch Number(or Lot Number)-批号用于标识一批的一个数字、字母和/或符号的唯一组合,从中可确定生产和销售的历史。 Bioburden–生物负载:可能存在与原料、原料药的起始物料、中间体或原料药中的微生物的水平和种类(例如,治病的或不治病的)。生物负载不应当当作污染,除非含量超标,或者测得治病生物。 Calibration–校验:证明某个仪器或装置在一适当的量程范围内测得的结果与一参照物,或可追溯的标准相比在规定限度内。 Computer System–计算机系统:设计安装用于执行某一项或一组功能的一组硬件元件和关联的软件。 Computerized System–计算机化系统与计算机系统整合的一个工艺或操作。Contamination–污染:在生产、取样、包装或重新包装、贮存或运输过程中,具化学或微生物性质的杂质或外来物质进入或沾染原料、中间体或原料药。 Contract Manufacturer–协议制造商:代表原制造商进行部分制造的制造商。 Critical–决定性的:用来描述为了确保原料药符合规格标准,必须控制在预定范围内的工艺步骤、工艺条件、测试要求或其他有关参数或项目。 Cross-Contamination–交叉污染:一种物料或产品对另一种物料或产品的污染。 Deviation–偏差:对批准的指令或规定的标准的偏离。 Drug(Medicinal)Product–药品:经最后包装准备销售的制剂(参见Q1A) Drug Substance–药物见原料药 Expiry Date(or Expiration Date)-有效期:原料药容器/标签上注明的日期,在此规定时间内,该原料药在规定条件下贮存时,仍符合规格标准,超过这以期限则不应当使用。 Impurity–杂质:存在与中间体或原料药中,任何不希望得到的成分。 Impurity Profile–杂质概况:对存在于一种原料药中的已知和未知杂质的描述。 In-Process Control(or Process Control)-中间控制:生产过程中为监测,在必要时调节工艺和/或保证中间体或原料药符合其规格而进行的检查。 Intermediate–中间体:原料药工艺步骤中生产的、必须经过进一步分子变化或精制才能成为原料药的一种物料。中间体可以分离或不分离。 Manufacture–制造:物料的接收、原料药的生产、包装、重新包装、贴签、重新贴签、质量控制、放行、贮存和分发以及相关控制的所有操作。 Material–物料:原料(起始物料,试剂,溶剂),工艺辅助用品,中间体,原料药和包装及贴签材料的统称。
. . 品质管理名词(中英文对照) QE=品质工程师(Quality Engineer ) MSA: Measurement System Analysis 量测系统分析 LCL: Lower Control limit 管制下限 Control plan 管制计划 Correction 纠正 Cost down 降低成本 CS: customer Sevice 客户中心 Data 数据 Data Collection 数据收集 Description 描述 Device 装置 Digital 数字 Do 执行 DOE: Design of Experiments 实验设计 Environmental 环境 Equipment 设备 FMEA: Failure Mode and Effect analysis 失效模式与效果分析 FA: Failure Analysis 坏品分析 FQA: Final Quality Assurance 最终品质保证 FQC: Final Quality control 最终品质控制 Gauge system 量测系统 Grade 等级 Inductance 电感 Improvement 改善 Inspection 检验 IPQC: In Process Quality Control 制程品质控制 IQC: Incoming Quality Control 来料品质控制 ISO: International Organization for Standardization 国际标准组织 LQC: Line Quality Control 生产线品质控制 LSL: Lower Size Limit 规格下限 Materials 物料 Measurement 量测 Occurrence 发生率 Operation Instruction 作业指导书 Organization 组织 Parameter 参数 Parts 零件 Pulse 脉冲 Policy 方针 Procedure 流程 Process 过程 Product 产品 Production 生产 Program 方案 Projects 项目 QA: Quality Assurance 品质保证 QC: Quality Control 品质控制 QE: Quality Engineering 品质工程 QFD: Quality Function Design 品质机能展开 Quality 质量 Quality manual 品质手册 Quality policy 品质政策 Range 全距 Record 记录 Reflow 回流 Reject 拒收 Repair 返修 Repeatability 再现性 Reproducibility 再生性 Requirement 要求 Residual 误差 Response 响应 Responsibilities 职责 Review 评审 Rework 返工 Rolled yield 直通率 sample 抽样,样本 Scrap 报废 SOP: Standard Operation Procedure 标准作业书 SPC: Statistical Process Control 统计制程管制 Specification 规格 SQA: Source(Supplier) Quality Assurance 供应商品质保证 Taguchi-method 田口方法 TQC: Total Quality Control 全面品质控制 TQM: Total Quality Management 全面品质管理 Traceability 追溯 UCL: Upper Control Limit 管制上限 USL: Upper Size Limit 规格上限 Validation 确认 Variable 计量值 Verification 验证 Version 版本 QCC Quality Control Circle 品质圈/QC 小组 PDCA Plan Do Check Action 计划 执行 检查 总结