变压器专业中英文词汇
- 格式:doc
- 大小:138.00 KB
- 文档页数:22
45ºmitred joint 45º斜接缝
a complete 成套设备
a lamination stack 一叠铁心
A-A enlarged A-A放大
A-A section A-A剖面
abbreviation 缩写
abscissa X-axis 横坐标
absorbent 吸附剂
absorption ratio of insulation resistance 绝缘电阻吸收比acceleration 加速度
acceptance inspection 验收检验
accessories 附件
accuracy 准确度
accuracy class 准确级次
accuracy limit factor 准确限值因数
acetic acid ethylic 醋酸
acetone 丙酮
acetone extraction of insulating material 绝缘材料丙酮抽出物acetylene 乙炔
acid value 酸值
acryl 丙烯
active aluminium oxide (activated alumine) 活性氧化铝
active part assembly 器身装配
additional insulation of lead 引线附加绝缘
additional loss 附加损耗
admittance 导电率
air (water) cooler 风(水)冷却品
air core reactor 空心电抗器
air exhausting pipe 导气管
air gap 空气隙
alignment对中心(不对中心)
alkyd base lacquer 酚醛漆
aluminium-alloy conductor 铝合金导线
ambient temperature 环境温度
angle 角钢(槽钢)
angular contact ball bearing 向心止推滚珠轴承
annealed conductor 退火导线
annex (appendix) to the contract合同附件
annular gear 内齿轮
anticoagulent 抗凝剂
anti-corna coating 防叠层
anti-dust washer 防尘垫圈
anti-magnetic steel (low-temperature steel) 抗磁钢(低温钢)antioxidant 抗氧化剂
antirust primer 防锈底漆
apparent charge 视在电荷
approximate 近似于
arc-suppression reactor 消弧电抗器
argon protected welding 氩弧焊
ascending flanged base 升高座
assignment for technical design 技术任务书
atmospheric over voltage 大气过电压
autographic recording instrument 自动记录仪表
automatic assembly scaffold 自动升降装配架
automatic lathe 自动车床
automatic submerged-arc wilding 埋弧自动焊
autotransformer 自耦变压器
autotransformer regulator 自耦调压器
auxiliary winding 辅助线圈
availability 可用性
axial (radial) leakage flux 轴向(径向)漏磁通
axial strip 轴向撑条
aximum (minimum) tapping最大最小分接m
backing off lathe 铲背车床
bakelite coated insulating paper 上胶绝缘纸
bakelized paper board(cpoxy resin glass-fibre) 胶纸板(环氧玻璃布板)balance reactor 平衡电抗器
ballast 镇流器
band saw 带锯床
band spring 板弹簧
banding wire (rope) 绑线(绳)
barrel (petroleum) 桶(石油)
base plate of rating plate 铭牌底板
basic parts 基础件
B-B tuned by B-B转
beaker烧杯
beaker flask 坩埚
beaker flask 锥形瓶
bearing 轴承
bell type tank 钟罩式油箱
bench drill 台钻
bending die for steel tube 钢管压弯模
bending press 折板机
bending press (brake) 折板机(液压)
bevel gear 伞齿轮
block diagram 方框图
blue print 蓝图
booster (pump) 增压泵