下载文档原格式
Accommodation 适应性Aerodynamics 空气动力学Air Conditioner 空调Air Drag 风阻Air Suspension 空气悬挂Analysis 分析Anti Corrosion 防腐Anti Rust 防锈Ashtray 烟灰盒Assembly 装配Assistant’s seat 副驾驶座Attaching Parts 附件Azimuth 方位（角）（极坐标）Back Angle 靠背角Backrest 靠背Backup Lamp 倒车灯Binocular Obstruction 双眼盲区BIW (Body-In-White) 白车身Blower 风机Body 车身，车体Bolt 螺栓Bonneted Cab 凸头驾驶室Bracket 托架Breakdown 分块Bumper 保险杠Bushing 衬套Case 壳体Caution Plate 警告牌Centroid 重心Cigarette Lighter 点烟器Chassis 底盘Chassis Frame 车架Check Arm 限位器Clip 卡扣Cluster Meter 组合仪表盘Coat Hanger 衣帽架Coat Hook 衣帽钩Collar 套环Combination Switch 组合开关Comfort 舒适性Component 总成Concealed Wipers 隐藏式雨刮器Condenser 冷凝器Contour 轮廓线Controls 控制件Convex Mirror 凸面镜Coolant 冷却液Cooler 制冷器Crash 碰撞Cup Holder 水杯架Curtain 窗帘Curtain Rail 窗帘滑轨Curvilineal 曲线的Dash Board 前围内板Delivery of the Drawing 出图Displacement 位移Door Check 限位器Door Header Rail 车门顶轨Door Lock 车门锁Door Opening 门洞Door Outer Handle 车门外手柄Door Outer Panel 车门外板Door Panel 门护板Door Pocket 门袋Door Regulator 车门玻璃升降器Door Sash 车门窗框Door Striker 锁环Door Trim 车门护板Door Ventilator 三角窗Drip Rail 滴水凹槽顶轨Drive Configuration 驱动形式Dummy Plate 平衡板Dynamic 动态的Ellipsoid Surface 椭球面Emblem 商标Engine 发动机Engineering 工程Entrance Handrail 上车门扶手Entry & Exit 进出Ergonomics 人机工程学Eyellipse 眼椭圆Fatigue Analysis 疲劳分析FEM (Finite Element Method) 有限元Fender 翼子板Fender Protector 挡泥护板Fender Stay 挡泥撑条Fender Welt 挡泥衬板Field of View 视野Finish Washer 精加工垫圈Fire Fighting Truck 消防车Fixed 固定的Flange Bolt 凸缘螺栓Fleece 绒毛织物Floor Insulator 地板隔热层Fluid Reservoir 贮液罐Fog Lamp 雾灯Fore/aft 前后Forward Control 平头Frame 车架Front Overhang 前悬Front Panel 前挡板，前围外板Front Turn Signal Lamp 前转向灯Fuse & Relay Box 保险丝和继电器箱Garnish 装饰板Gauge 量表Glare-free 防眩目Glass Run Channel 玻璃滑槽Glazing Rubber Plate 镶玻璃用橡胶板Glove Box 杂物盒Gradeability 爬坡度Grille 格栅Grip 扶手Grommet 密封圈Ground Clearance 离地间隙Halogen Headlamp 卤素大灯Handle Cover 手柄罩Head Contour 头廓包络线Head Restraints 头枕Headlamp 前大灯Headliner 顶棚Headlining 顶棚内饰Headrest 头枕Heater 加热器Heater Plumbing 取暖装置管路Height Adjuster 高度调节器High-mount 高位Hinge 铰链Hinge Bracket 铰链托架Holder 支架Hood 发动机罩Hook 挂钩Hose 软管Impact 碰撞In-line 直列Ingress/egress 进出Inside Lock Knob 内锁止按钮Instrument Panel 仪表板Interior Trim 内饰Intermittent Wiper 间歇式刮水器Joint 接头Joint Duct 连接管道Kinematics 运动学Lateral 横向Lever 杆籁绅士Plate 牌照籁绅士Plate Bracket 牌号托架籁绅士Plate Lamp 车牌灯Lift-up Type 翻转式（前围外板）Linear 线性的Load 载荷Lock Cylinder & Key 锁芯和钥匙Longitudinal 长度方向的Loose Panel 可卸盖板Lower Apron 下挡板Lumbar Support 腰托Luxury Interior Level 豪华内饰Mud Guard 挡泥板Mud Shield 挡泥板（侧）Male-to-Female Ration 男女比例Manikin 人体模型Manoeuvrable 操纵灵活的Meeting Minutes 会议纪要Member 横梁Meter & Gauge 仪表盘Meter Cable 仪表电缆Meter Cluster 仪表束Meter Cover 仪表面罩Meter Face 仪表面Meter Hood 仪表罩Milling 铣Mirror Holder 后视镜支架Model 模型Moquette 绒面Mount 悬置Movable Part 运动件Mudguard 挡泥板Muffler 排气消声器Muscular Contour 强壮的外形（造型风格）））Non-linear 非线性的Nozzle 喷嘴Nut 螺母Operation Hardware 开闭、锁紧装置Optimization 优化Ornament 标识Outlet 出风口Overhead Console Box 高架箱Packing 衬垫Parking Brake Lever 驻车制动手柄Percentile 百分位Perimeter 周长、周边Pillar 立柱Pin 销Pivot Point 关节点Plain Washer 平垫圈Plan View 俯视图Plate & Label 名牌和标识Plate Nut 板螺母Pneumatic Spring 空气弹簧Pocket 凹槽Pocket Facing 凹槽镶面Power Steering 动力转向Presentation 展示Push Button 按钮Push-on Spring Nut 顶推弹簧螺母Quarter Panel 后顶盖侧板Quarter Window 侧车窗Radiator 散热器Raised Roof 高顶Rear Overhang 后悬Rear View Mirror 后视镜Rear Wall 后围Reclining 倾斜Reflector 反射板Regulation 法规Reinforcement 加强件Rendering 效果图Requirement 要求Resin 树脂Retainer 护圈Rigidity 刚度Rivet 铆钉Roof Console 高架箱Roof Hatch 天窗Roof Panel 车顶板Room Lamp 室内灯Root-Mean-Square 均方根Round Oval Instrumentation 环抱式仪表板Safety 安全性Screw 螺钉Screw Grommet 密封圈螺钉Scuff 压条（门槛处）Seat Bench 长排座Seat Support 座椅支架Seat Track 座椅导轨Self-Supporting 自承载式Service Parts 修理配件Set Screw 定位螺钉Shim 调整垫片Shin-Knee Contour 膝部包络线Shock Absorber 减振器Side View 侧视图Sight Line 视线Silencer 消声器Sill 横梁Simulation 模拟Sketch 草效果图Sleeper 卧铺Sleeping Bed 卧铺Sleeping Berth 卧铺Slide Adjuster 前后滑动调节器Snap Ring 开口环Snorkel 进气管Snowplow 除雪车Spacer 隔环Speedometer 车速仪Splash Apron 侧挡泥板Spot Welding 点焊Static 静态的Steering Column 转向柱Steering Column Adjuster 转向柱调整器Steering Gear 转向机构Steering Wheel 方向盘Step Plate 踏脚板Step Protector 脚踏板护板Stiffener 加强肋Stiffness 刚度Stop Lamp 制动灯Stopper 挡块Strain 应变Strength 强度Stress 应力Structure 结构Styling 造型Sun Visor 遮阳板Surfacing 线图Suspension 悬架Switch 开关Tachograph & Speedometer 自记式转速记和车速表Tachometer 发动机转速表Tail Lamp 尾灯Tapping Screw 自攻螺钉Template 模板Ticket/Card Holder 名片夹Tilt 翻转（驾驶室）Tipper 自卸车Tonnage 吨位Torsional Stiffness 扭转刚度Tread 轮距Trim 饰件Trim Panel 装饰板Turning Radius 转弯半径Upper Console 高架箱Variant 变形车Ventilation 通风Vertical 垂直方向的Vinyl 乙烯基Washer 垫圈Water Proof Film 防水层Weather Strip 密封条Wear-Resistant 防磨Windscreen 风窗Windshield 风窗Windshield Washer 挡风玻璃洗涤器Windshield Wiper 挡风玻璃刮水器Wiper 刮水器Wiper Arm 刮臂Wiper Blade 刮片Wiper Link Assembly 刮水器连杆组件Wiring Harness 线束07轮椅升降机Wheel chair lift图例legend工位station吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout合笼mate底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrution 爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engine 组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension 功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine 柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机I形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle 工作循环working cycle等压循环constant pressure cycle 理想循环ideal cycle热力循环thermodynamic cycle 冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging strokecompression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center) 上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption 空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor 制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower 功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency 充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency) 怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode) 额定工况declared working condition变工况variable working condition 稳定工况steady working condition 空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance 动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator07 reock frameadhanism casingacer环ad ring gasketad gasketer(cylinder sleeve)r linerer lineretplugallrtte bottum转子机）radius转子机）widthn chamberustion chamber combustion chamberrustion chamber室mbustion chamber室combustion chamber室cal combustion chamberction combustion chamberon chambertion combustion chamberustion chamberay chamber烧室mberhamber比io of combustion cahmber比ume ratio of combustion chamberof combustion chamber passage 口breather座earing bush seat罩rive(gear)cover孔盖door门explosion proof doorng caphanism coververair receiver塞iston塞tonpistonistond piston(convex head piston) ead pistonpistonn塞c piston塞earance piston活塞piston活塞ed piston活塞oled pistononedd衬簧expander裙tkbossbushing销g piston pin销g piston pin活塞销piston pin环piston ringpiston ringiston ringngne ringr ringringcontrol ring载双坡口油环loaded slotted oil control ring elled oil control ringvel topvel bottom环ge oil control ring ngted piston ringexpandergrooveland面g构rod杆机构ated connecting rod 杆机构ecting rod杆机构necting rodrodrod small endg rod big endrod shankecting rodade connecting rod ecting rode connecting rod connecting rod rod caprod bearingcrankshaftcrankshaftcrankshaftrankshaft曲轴ankshaftfront endmain journalal overlapng承thrust bearing earing shelloil passageeuseelalancereightvibration damperanceralanceralancersprocketalhaft通风装置nkcase ventilating system ng gearindle矩oment of inertiaarksystemshaft length性力ng inertia force,1st order 性力ng inertia force, 2nd order inertia force轴camshaft轴camshaft机构rive轴haftearing journalearing轮ccentricprocket齿轮ming gearear wheel）：swm45100 FanE『翻译中国』2004-5-27 14:07:30 te gear(counter gear)aft gearaft轴on imput shaft轴on output shaft齿轮轴on drive gear shafton main shaft轴on countershaft刚度shaft（变速比）on gear ratiorepressure力odulator pressureressureor or trimmer pressurere(input pump )置充油压力mic unit change pressure(output pump )il pumpegulator vavle阀gulator valve旁通阀bypass valvealvelvee生器n generatortor(shift torwer)veve控制阀ntrol valve锁止ockup换档系统utomatic control system 换档系统-hydraulic automatiec换档shfititshfithiftiftte shiftresisulepower shift程automatic shift automatic shft lementergear shift lever) ）变速杆ctork (gear shift fork)杆ar shift forkpedal叉道轨）ge(direct control)速ft (handle change)ontrole07空档位置neutral position直接驱动direct drive高速档top gear(high gear)低速档bottom gear(low speed gear)第一档first gear第二档second gear超速档overdirve gear经济档economic gear倒档reverse gear爬行档creeper gear驱动特性drive performance反拖特性coast performance定输入扭矩特性constant input torque performance全油门特性full throttle performance寄生损失特性no load (parasitic losses)performance 原始特性primary characteristic响应特性response characteristic吸收特性absorption characteristic全特性total external characteristic输入特性characteristic of enhance输出特性characteristic of exit力矩特性torque factor(coefficient of moment) 过载系数overloading ratio变矩系数torque ratio能容系数capacity factorr几何相似geometry similarity运动相似kinematic similarity动力相似dynamic similarity透穿性transparency万向节和传动轴universal joint and drive shaft万向节universal joint非等速万向节nonconstant velocity universal joint 等速万向节constant velocity universal joint准等速万向节near constant velocity universal joint 自承式万向节self-supporting universal joint非自承式万各节non self suporting universal joint 回转直径swing diameter等速平面constant velocity plane万向节夹角true joint angle十字轴式万向节cardan (hookes)universal joint 万向节叉yoke突缘叉flange york滑动叉slip yoke滑动节，伸缩节slip joint花键轴叉slip shaft yoke轴管叉（焊接叉）tube(weld yoke)十字轴cross(spider)十字轴总成cross assembly挠性元件总成flexible universal joint球销式万向节flexible member assembly双柱槽壳housing球环ball球头轴ball head球头钉button中心球和座centering ball and seat球笼式万向节rzeppa universal joint钟形壳outer race星型套inner race保持架cage可轴向移动的球笼式万向节plunging constant velocity joint筒形壳cylinder outer race柱形滚道星形套inner race withcylinder ball grooves 偏心保持架non-concentric cage滚动花键球笼式万向节ball spline rzeppa universal joint外壳outer housing内壳体inner housing球叉式万向节weiss universal joint球叉ball yoke定心钢球centering ball三球销万向节tripod universal joint三柱槽壳housing三销架spider双联万向节double cardan universal joint凸块式万向节tracta universal joint凸块叉fork yoke榫槽凸块tongue and groove couplijng凹槽凸块groove coupling传动轴drive shaft(propeller shaft)传动轴系drive line传动轴形式drive shaft type两万向节滑动的传动轴two -joint inboard slip ddiveshaft 两万向节外侧滑动传动轴two joint ouboard slip drive shaft 单万向节传动轴single joint coupling shaft组合式传动轴unitized drive shaft传动轴减振器drive shaft absorber传动轴中间轴承drive shaft center bearing传动轴管焊接合件weld drive shaft tube assembly传动轴特征长度drive shaft length传动轴谐振噪声resonant noise of rive shaft传动轴的临界转速critical speed of drive shaft传动轴总成的平衡balance of drive shaft assembly允许滑动量slip相位角phase angle传动轴安全圈drive shaft safety strap驱动桥drive axle(driving axle)类型type断开式驱动桥divided axle非独立悬架式驱动桥rigid dirve axle独立悬架式驱动桥independent suspension drive axlesteering drive axle贯通式驱动桥tandem axles“三速”贯通轴"three-speed" tandem axles单驱动桥single drive axle多桥驱动multiaxle drive减速器reducer主减速器final drive单级主减速器single reduction final drive双级主减速器double reduction final drive前置式双级主减速器front mounted double reduction final drive后置式双级主减速器rear mounted double reduction final drive上置式双级主减速器top mounted double reducton final drive行星齿轮式双级主减速器planetary double reduction final drive贯通式主减速器thru-drive双速主减速器two speed final drive行星齿轮式双速主减速器two speed planetary final drive双级双速主减速器two speed double reduction final drive轮边减速器wheel reductor(hub reductro)行星圆柱齿轮式轮边减速器planetary wheel reductor行星锥齿轮式轮边减速器differential geared wheel reductor(bevelepicyclick hub reductor) 外啮合圆柱齿轮式轮边减速器spur geared wheel reductor差速器锥齿轮式差速器bevel gear differential圆柱齿轮式差速器spur gear differential防滑式差速器limited -slip differential磨擦片式自锁差速器multi-disc self -locking differential凸轮滑滑块自锁差速器self-locking differential with side ring and radial cam plate 自动离合式自锁差速器automotive positive locking differential强制锁止式差速器locking differential液压差速器hydraulic differential轴间差速器interaxial differential差速器壳differential carrieer(case)主降速齿轮final reduction gear驱动轴减速比axle ratio总减速比total reduction ratio主降速齿轮减速比final reduction gear ratio双减速齿轮double reduction gear差速器主齿轮轴differential pinion-shaft差速器侧齿轮differential side gear行星齿轮spider gear(planetary pinion)螺旋锥齿轮spiral bevel gear双曲面齿轮hypoid gear格里林齿制gleason tooth奥林康型齿制oerlikon tooth锥齿轮齿数number of teeth in bevel gears and hypoid gears锥齿轮齿宽face width of tooth in bevel gears and hypoid gears 平面锥齿轮plane bevel gear奥克托齿形octoid form平顶锥齿轮contrate gear齿面接触区circular tooth contact齿侧间隙backlash in circular tooth差速器十字轴differential spider差速器锁止机构differential locking -device差速器锁止系数differential locking factor差速器壳轴承carrier bearing桥壳axle housing整体式桥壳banjo housing可分式桥壳trumpet-type axle housing组合式桥壳unitized carrier-type axle housing对分式桥壳split housing冲压焊接桥壳press-welding axle housing钢管扩张桥壳expanded tube axle housing锻压焊接桥壳forge welding axle housing整体铸造式桥壳cast rigid axle housing半轴axle shaft全浮式半轴full-floating axle shaft半浮式半轴semi-floating axle shaft四分之三浮式半轴three-quarter floating axle shaft 驱动桥最大附着扭矩slip torque驱动桥额定桥荷能力rating axle capactiy驱动桥减速比driveaxle ratio驱动桥质量drive axle mass单铰接式摆动轴single-joint swing axle双铰接式摆动轴double joint swig axle悬架系suspension system悬架suspension类型type非独立悬架rigid axle suspension独立悬架independent suspension平衡悬架equalizing type of suspension组合式悬架combination suspension可变刚度悬架。
一、汽车内外饰Trim：车身内饰Marriage：车身和底盘合装Chassis：车身底盘EOL：End of line终检线Head Light头灯。
根本就是直译，就是把“头”和“灯”二个名词凑在一起，前面的名词当作形容词，简单明了，学过一次就不会忘记！Grille水箱护罩。
这个字也很好记，不过拼法千万要正确，最后的那个“e”千万别忘了，否则就变成了“烧烤”的意思了！如果要讲“镀铬水箱护罩”，那就是Chrome Grille。
Fog Light雾灯。
和头灯一样，就是把雾﹙Fog﹚和灯﹙Light﹚凑在一起就行了，英文里这类的用法非常多，像是红绿灯就是Traffic Light，车流就是Traffic Flow。
Bumper保险杠，这个词是从Bump-凸起加上“er”字尾所演化而来的，因为保险杆就是车头、车尾的凸出物，装设保险杆的目的就是用来抵挡轻微的碰撞、以保护车身的。
如果把Bump加“y”变成Bumpy，那意思就变成了“颠簸”，It is indeed a bumpy road-这条路真是够颠簸的！Air Intake进气口。
现代化的汽车讲究低风阻、低油耗，车身要楔型、要流线，如此一来车头迎风面积就变得很小，难以设计直立式的水箱护罩，再加上讲求车室空间利用率，因此前轮驱动车大行其道，前驱车为了有效利用空间，引擎经常横置，因此曲轴变成面对左右翼子板，也无法带动风扇直接从车头吸气和散热。
因此，现代化的车子多半将进气口设置于保险杆上，至于引擎散热的问题就交给转速极高的电动风扇。
Indicator方向灯。
Indicate是动词，意思是“指示”，把字尾改成“or”，意思就是“显示器”，指示车子是要左转、右转的“显示器”就是中文里的“方向灯”。
Windshield挡风玻璃。
这也是二个字所组合成的，但它已经进化成一个独立的字了，Wind是“风”、Shield 是“遮蔽”、“阻挡”的意思，Windshield就是挡风玻璃，和方向灯一样，英文里也没有玻璃的字眼出现。
汽车专业英语汇总一、Vehicle classification 汽车分类1.1 Car 轿车1。
2 Bus 客车1.3 Motor truck 货车1。
4 special purpose vehicle 专用汽车二、Vehicle construction 汽车构造2。
1 Main components of vehicle 汽车主要组成2。
2 Vehicle performance 汽车性能2.3 engine position 发动机布置三、Vehicle dimensions汽车尺寸四、Wheel alignment前轮定位五、Diameter of turning circle 转弯直径第二类ENGINE 发动机一、Engine construction 发动机构造二、Essential term 基本术语发动机工作原理3.1 Four—stroke gasoline engine operationprinciple3.2 Four—stroke diesel engine operationalprinciple3.3 Two—stroke gasoline engine operationprinciple3。
4 Two-stroke diesel engine operation principle二冲程柴油机工作原理四、Engine performance 发动机性能曲柄连杆机构5。
2 Piston,connecting rod 活塞连杆组5。
3 Crankshaft,flywheel 曲轴飞轮组六、Valve mechanism 配气机构6。
1 Side valve 侧置气门6。
2 Overhead valve 顶置气门6.3 Overhead valve 顶置气门6。
4 Valve-timing diagram 配气相位图七、Gasoline engine—fuel system汽油机供油泵7.1 Fuel system 供油泵7.2 Air cleaner 空气滤清器7。
汽车车身术语汽车车身术语WTD standardization office【WTD 5AB- WTDK 08- WTD 2C】设计术语车身：body 供驾驶员操作，以及容纳乘客和货物的场所。
主要作用是为乘员提供安全、舒适的乘坐环境，隔绝振动和噪声，不受恶劣气候的影响。
包括车身本体和装饰件、开启件、机构件、附件及其它可拆卸结构件。
承载式车身：unitized body ,integral body 无独立车架的整体车身结构形式半承载式车身：semi-integral body 车身与车架刚性连接，车身部分承载的结构形式非承载式车身：separate frame construction 悬置于车架上的车身结构形式一厢式车身：one box type body 发动机舱、客舱和行李舱在外形上形成一个空间形态的车身两厢式车身：two box type body ,hatch back body 发动机舱、客舱和行李舱在外形上形成两个空间形态的车身三厢式车身：three box type body 发动机舱、客舱和行李舱在外形上形成各自独立形态的车身封闭车身：closing body 顶盖作为车身本体一部分的车身开式车身：opening body, convertible body 客舱顶为敞顶或客舱顶按需要可启闭的车身驾驶室：cab, front body 载货汽车的车身平头驾驶室：forward control cab, cab over engine 发动机一半以上的长度位于风窗玻璃最前端的后方的驾驶室长头驾驶室：conventional cab, normal control cab 有车前板制件，除平头驾驶室以外的驾驶室翻转式驾驶室：tilting cab 可整体向前倾翻的驾驶室单排座驾驶室：single cab 只有一排座位的驾驶室双排座驾驶室：double cab, crew cab 有钱后两排座位的驾驶室带卧铺驾驶室：sleeper cab, cab with bed 设有卧铺的驾驶室涂装车身：body on primer 经过涂装后的白车身白车身：BIW (body in white) 由车身本体、开启件及其它可拆卸结构件组成的总成车身本体：main body, body structure 结构件与覆盖件焊接或铆接后不可拆卸的总成车身骨架：body skeleton 主要为保证车身的强度和刚度而构成的空间框架结构驾驶区：driver compartment 供驾驶员操作和乘坐的区域乘客区：passenger compartment 供乘客使用的区域客舱：passenger space 供乘员使用的区域，及驾驶区和乘客区的总称发动机舱：engine compartment 供放置发动机的空间行李舱：luggage compartment 供放置行李的车身空间车身前部：front body 客舱以前的车身部分车身后部：rear body 客舱以后的车身部分车身底部：under body 客舱、发动机舱、行李舱底部的总称车身侧部：side body 车身侧面部分的总称车身裙部：skirt 地板以下的车身侧围部分地板系统：floor 位于车身的地部，由骨架、板件、地谈及有关车身附件等组成的零部件的总称前围系统：body front wall, front face 位于客舱的前部，由骨架、板件、风窗玻璃及有关车身附件等组成的零部件的总称侧围系统：body side wall 位于客舱和行李舱的两侧，由骨架、板件、侧窗及有关车身附件等组成的零部件的总称后围系统：body back wall, body rear wall位于客舱的后部，由骨架、板件、后窗玻璃及有关车身附件等组成的零部件的总称顶盖系统：roof 位于客舱的顶部，由骨架、板件、内饰及有关车身附件等组成的零部件的总称车门系统：door 车身上的门，由板件、内饰、玻璃及车门附件等组成的零部件的总称车身覆盖件：cover panel 覆盖在车身骨架表面上的板制件车身结构件：body structural, body skeleton, body frame 组成车身本体，支撑覆盖件，并保证车身强度和刚度的零部件车前板制件：front body shell, front sheet metal 车身前部覆盖发动机和车轮的零部件的总称开启件：compartment door 车身上可启闭的各种舱门的结构件机构件：hardware 具有操纵、运动、连接功能的部件装饰件：trim, garnish 起装饰和保护作用的部件附件：body accessories车身中具有独立功能并成为一个分总成的部件。
汽车专用术语大全（英文注释）1、引擎系统(Automotive Engine System)燃烧室(Combustion Chamber)活塞到达上死点后其顶部与汽缸盖之间的空间，燃料即在此室燃烧。
压缩比(Compression Ratio)活塞在下死点的汽缸之总容积除以活塞在上死点的总容积(燃烧室容积)，所得的值就称为压缩比。
连杆(Connecting Rod)引擎中连接曲轴与活塞的连接杆。
冷却系统(Cooling System)可藉冷却剂的循环，将多余的热量移出引擎，以防止过热的系统。
在水冷式的引擎中，包括水套、水泵、水箱及节温器。
曲轴箱(Crankcase)引擎下部，为曲轴运转的地方，包括汽缸体的下部和油底壳。
曲轴(Crankshaft)引擎的主要旋转机件，装上连杆后，可承接连杆的上下(往复)运动变成循环(旋转)运动。
曲轴齿轮(Crankshaft Gear)装在曲轴前端的齿轮或键齿轮，通常用来代动凸轮轴齿轮，链条或齿状皮带。
汽缸体(Cylinder Block)引擎的基本结构，引擎所有的零附件都装在该机件上，包括引擎汽缸及曲轴箱的上半部。
汽缸盖(Cylinder Head)引擎的盖子及封闭汽缺的机件，包括水套和汽门及冷却片。
爆震(Detonation)为火焰的撞击或爆声，在火花点火引擎的燃烧室内，因为压过的空气燃料混合气会自燃，于是使部份未燃的混合气产生二次点火(在火星塞点火之后)，因而发出了爆声。
排气量(Displacemint)在引擎的某一循环运作中，能将全部空气及混合气送入所有汽缸的能力，也是指一个活塞从一个行程运作至另一行程所能排的体积。
引擎(Engine)一种能将热能转变为机械能的机械：一种可将燃料燃烧产生机械动力的装置；有时可视为一种发动机。
风扇皮带(Fan Belt)一种由曲轴带动的皮带，其主要目的是带动引擎风扇和水泵。
浮筒油面高度(Float Level)化油器浮筒室内，浮筒浮起而顶住针阀，堵住进油口，使油不再流入浮筒室时，油面的高度。
汽车英语词汇大全1. Car Types:- Sedan: A car with a closed body, a trunk for luggage, and four doors.- SUV (Sport Utility Vehicle): A large car with a high ground clearance and often four-wheel drive.- Hatchback: A car with a rear door that opens upwards and a rear cargo area.- Coupe: A two-door car with a sporty design and often a sloping roofline.- Convertible: A car with a folding or retractable roof, allowing for an open-air driving experience.汽车类型：- 轿车：一种带有封闭车身、行李厢和四个车门的车辆。
- SUV（运动型多用途车）：一种车身较大、离地间隙较高且通常带有四轮驱动的车辆。
- 掀背车：一种拥有向上开启的后车门和后部货物区的车辆。
- 跑车：一种拥有两个车门、运动设计并通常带有倾斜车顶线的车辆。
- 敞篷车：一种具有可折叠或收放式车顶的车辆，可提供开放式驾驶体验。
2. Car Parts:- Engine: The motor that powers the car.- Transmission: The system that transmits power from the engine to the wheels.- Brakes: The system that slows down or stops the car.- Steering wheel: The control used to steer the car.- Headlights: Lights at the front of the car for visibility at night.汽车零部件：- 发动机：为汽车提供动力的引擎。
Accommodation 适应性Aerodynamics 空气动力学Air Conditi oner 空调Air Drag 风阻Air Suspensi on 空气悬挂Analysi s 分析Anti Corrosion 防腐Anti Rust 防锈Ashtray 烟灰盒Assembly 装配Assi stant’s seat 副驾驶座Attaching Parts 附件Azimuth 方位（角）（极坐标）Back Angle 靠背角Backrest 靠背Backup Lamp 倒车灯Binocular Obstruction 双眼盲区BIW (Body-In-White) 白车身Blower 风机Body 车身，车体Bolt 螺栓Bonneted Cab 凸头驾驶室Bracket 托架Breakdown 分块Bumper 保险杠Bushing 衬套Case 壳体Caution Plate 警告牌Centroid 重心Cigarette Lighter 点烟器Chassis 底盘Chassis Frame 车架Check Arm 限位器Clip 卡扣Cluster Meter 组合仪表盘Coat Hanger 衣帽架Coat Hook 衣帽钩Collar 套环Combination Switch 组合开关Comfort 舒适性Component 总成Concealed Wipers 隐藏式雨刮器Condenser 冷凝器Contour 轮廓线Controls 控制件Convex Mirror 凸面镜Coolant 冷却液Cooler 制冷器Crash 碰撞Cup Holder 水杯架Curtain 窗帘Curtain Rail 窗帘滑轨Curvilineal 曲线的Dash Board 前围内板Delivery of the Drawing 出图Displacement 位移Door Check 限位器Door Header Rail 车门顶轨Door Lock 车门锁Door Opening 门洞Door Outer Handle 车门外手柄Door Outer Panel 车门外板Door Panel 门护板Door Pocket 门袋Door Regulator 车门玻璃升降器Door Sash 车门窗框Door Striker 锁环Door Trim 车门护板Door V entilator 三角窗Drip Rail 滴水凹槽顶轨Drive Configuration 驱动形式Dummy Plate 平衡板Dynamic 动态的Ellipsoid Surface 椭球面Emblem 商标Engine 发动机Engineering 工程Entrance Handrail 上车门扶手Entry & Exit 进出Ergonomics 人机工程学Eyellipse 眼椭圆Fatigue Anal ysis 疲劳分析FEM (Finite Element Method) 有限元Fender 翼子板Fender Protector 挡泥护板Fender Stay 挡泥撑条Fender Welt 挡泥衬板Field of View 视野Finish Washer 精加工垫圈Fire Fighting Truck 消防车Fixed 固定的Flange Bolt 凸缘螺栓Fleece 绒毛织物Floor Insulator 地板隔热层Fluid Reservoir 贮液罐Fog Lamp 雾灯Fore/aft 前后Forward Control 平头Frame 车架Front Overhang 前悬Front Panel 前挡板，前围外板Front Turn Signal Lamp 前转向灯Fuse & Relay Box 保险丝和继电器箱Garnish 装饰板Gauge 量表Glare-free 防眩目Glass Run Channel 玻璃滑槽Glazing Rubber Plate 镶玻璃用橡胶板Glove Box 杂物盒Gradeability 爬坡度Grille 格栅Grip 扶手Grommet 密封圈Ground Clearance 离地间隙Halogen Headlamp 卤素大灯Handle Cover 手柄罩Head Contour 头廓包络线Head Restraints 头枕Headlamp 前大灯Headliner 顶棚Headlining 顶棚内饰Headrest 头枕Heater 加热器Heater Plumbing 取暖装置管路Height Adjuster 高度调节器High-mount 高位Hinge 铰链Hinge Bracket 铰链托架Holder 支架Hood 发动机罩Hook 挂钩Hose 软管Impact 碰撞In-line 直列Ingress/egress 进出Inside Lock Knob 内锁止按钮Instrument Panel 仪表板Interior Trim 内饰Intermittent Wiper 间歇式刮水器Joint 接头Joint Duct 连接管道Kinematics 运动学Lateral 横向Lever 杆籁绅士Plate 牌照籁绅士Plate Bracket 牌号托架籁绅士Plate Lamp 车牌灯Lift-up Type 翻转式（前围外板）Linear 线性的Load 载荷Lock Cylinder & Key 锁芯和钥匙Longitudinal 长度方向的Loose Panel 可卸盖板Lower Apron 下挡板Lumbar Support 腰托Luxury Interior Level 豪华内饰Mud Guard 挡泥板Mud Shield 挡泥板（侧）Male-to-Female Ration 男女比例Manikin 人体模型Manoeuvrable 操纵灵活的Meeting Minutes 会议纪要Member 横梁Meter & Gauge 仪表盘Meter Cable 仪表电缆Meter Cluster 仪表束Meter Cover 仪表面罩Meter Face 仪表面Meter Hood 仪表罩Milling 铣Mirror Holder 后视镜支架Model 模型Moquette 绒面Mount 悬置Movable Part 运动件Mudguard 挡泥板Muffler 排气消声器Muscular Contour 强壮的外形（造型风格）））Non-linear 非线性的Nozzle 喷嘴Nut 螺母Operation Hardware 开闭、锁紧装置Optimization 优化Ornament 标识Outlet 出风口Overhead Console Box 高架箱Packing 衬垫Parking Brake Lever 驻车制动手柄Percentile 百分位Perimeter 周长、周边Pillar 立柱Pin 销Pivot Point 关节点Plain Washer 平垫圈Plan V iew 俯视图Plate & Label 名牌和标识Plate Nut 板螺母Pneumatic Spring 空气弹簧Pocket 凹槽Pocket Facing 凹槽镶面Power Steering 动力转向Presentation 展示Push Button 按钮Push-on Spring Nut 顶推弹簧螺母Quarter Panel 后顶盖侧板Quarter Window 侧车窗Radiator 散热器Raised Roof 高顶Rear Overhang 后悬Rear View Mirror 后视镜Rear Wall 后围Reclining 倾斜Reflector 反射板Regulation 法规Reinforcement 加强件Rendering 效果图Requirement 要求Resin 树脂Retainer 护圈Rigidity 刚度Rivet 铆钉Roof Console 高架箱Roof Hatch 天窗Roof Panel 车顶板Room Lamp 室内灯Root-Mean-Square 均方根Round Oval Instrumentation 环抱式仪表板Safety 安全性Screw 螺钉Screw Grommet 密封圈螺钉Scuff 压条（门槛处）Seat Bench 长排座Seat Support 座椅支架Seat Track 座椅导轨Self-Supporting 自承载式Service Parts 修理配件Set Screw 定位螺钉Shim 调整垫片Shin-Knee Contour 膝部包络线Shock Absorber 减振器Side V iew 侧视图Sight Line 视线Silencer 消声器Sill 横梁Simulation 模拟Sketch 草效果图Sleeper 卧铺Sleeping Bed 卧铺Sleeping Berth 卧铺Slide Adjuster 前后滑动调节器Snap Ring 开口环Snorkel 进气管Snowplow 除雪车Spacer 隔环Speedometer 车速仪Splash A pron 侧挡泥板Spot Weldi ng 点焊Static 静态的Steering Column 转向柱Steering Column Adjuster 转向柱调整器Steering Gear 转向机构Steering Wheel 方向盘Step Plate 踏脚板Step Protector 脚踏板护板Stiffener 加强肋Stiffness 刚度Stop Lamp 制动灯Stopper 挡块Strain 应变Strength 强度Stress 应力Structure 结构Styling 造型Sun V isor 遮阳板Surfacing 线图Suspensi on 悬架Switch 开关Tachograph & Speedometer 自记式转速记和车速表Tachometer 发动机转速表Tail Lamp 尾灯Tapping Screw 自攻螺钉Template 模板Ticket/Card Holder 名片夹Tilt 翻转（驾驶室）Tipper 自卸车Tonnage 吨位Torsional Stiffness 扭转刚度Tread 轮距Trim 饰件Trim Panel 装饰板Turning Radius 转弯半径Upper Console 高架箱V ariant 变形车V entilation 通风V ertical 垂直方向的Vinyl 乙烯基Washer 垫圈Water Proof Film 防水层Weather Strip 密封条Wear-Resistant 防磨Windscreen 风窗Windshield 风窗Windshield Washer 挡风玻璃洗涤器Windshield Wiper 挡风玻璃刮水器Wiper 刮水器Wiper Arm 刮臂Wiper Blade 刮片Wiper Link Assembly 刮水器连杆组件Wiring Harness 线束b248b24807-09-08 12:22 轮椅升降机Wheel chair lift图例legend工位stati on吊运装置overhead hoist更衣室restroom1号厂房工艺布置方案图proposal of the Plant I layout合笼mate底盘平移台chassi s shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassi s左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutti ng内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoi st小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine hol ding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphating仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrution 爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resi stant聚碳化透镜poly-carbonate len镀锌板galvanized plate搭接lap亮丽的外表smart apperance隐藏式固定concealed fastening水洼ponding发动机中置式客车bus with under floor engi ne组合式客车车身modular bus body薄壳式结构shell constructi on衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel returnability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test 极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping raito of suspension 功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tyre绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pul se response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test汽车发动机类型type发动机engine内燃机intenal combusiton engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injecti on engine火花点火式发动机spark ignition engi ne压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engi ne柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engi ne直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engi ne油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine 柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engi ne双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed pi ston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engi ne直列式发动机in-line engi ne星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engi ne顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side val ve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engi ne性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke 换气压缩行程exchange-compression stroke 止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center) 上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept vol ume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression rati o临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effecti ve pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effecti ve thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean pi ston speed发动机转速engine speed (rotational frequency) 怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed 调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode) 额定工况declared working condition变工况variable working condition稳定工况steady working conditi on空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-cl ockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics 万有特性mapping characteri stics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体statorb248b24807-09-08 12:23 缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechani sm casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsi diary combustion chamber预燃室prechamber涡流燃烧室`swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combusti on chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume rati o of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area rati o of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechani sm cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pi stonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head pi ston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston) 凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance pi ston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston 滑裙活塞slipper pi ston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander 滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating pi ston pin 半浮式活塞销semifloating pi ston pin 固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound pi ston ring 同心活塞环concentric piston ring 偏心活塞环eccentric piston ring 自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated pi ston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod bi g end连杆杆身connecting rod shank副连杆slave connecti ng rod叉形连杆fork-and-blade connecting rod 主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper 扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibrati on balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order 二级往复贯性力reciprocating inertia force, 2nd order 离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece cam shaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race cam shaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮汽车词汇（2）出处：作者：swm45100 FanE『翻译中国』2004-5-27 14:07:30 中间齿轮intermediate gear(counter gear)副轴齿轮counter shaft gear副轴counter shaft变速器输入轴transmission imput shaft变速器输出轴transmission output shaft变速器主动齿轮轴transmission drive gear shaft变速器主轴transmission main shaft变速器中间轴transmission countershaft变速器轴的刚度rigidity of shaft变速齿轮比（变速比）transmission gear rati o传动比gear ratio主压力line pressure调制压力modulated pressure真空调制压力vacuum modulator pressure速控压力governor pressure缓冲压力compensator or trimmer pressure 限档压力hold presure前油泵front pump (input pump )液力传动装置充油压力hydrodynamic unit change pressure 后油泵gear pump (output pump )回油泵scavenge oil pump调压阀pressure -regulator vavle电磁阀调压阀solenoid regulator valve液力变矩器旁通阀converter bypass val ve速控阀governor valve选档阀selectro val ve换档阀shift valve信号阀signal valve继动阀relay valve换档指令发生器shift pattern generator档位指示器shift indicator(shift torwer)先导阀priority valve流量阀flow valve重迭阀overlap valve液力减速器控制阀retarder control val ve液力起步fluid start零速起动stall start液力变矩器锁止converter lockup全液压自动换档系统hydraulic automatic control system 电液式自动换档系统electronic -hydraulic automatiec 换档shift升档upshift降档downshift动力换档power shfit单向离合器换档freewheel shfit人工换档manual shfit自动换档automaitc shfit抑制换档inhibited shift超限换档overrun shift强制换档forced shift换档点shift point叶片转位blade angle shift换档滞后shift hysteresis换档循环shift schedule换档规律process of power shift动力换档过程timing换档定时property of automatic shift换档品质property of automatic shft换档元件engaging element换档机构操纵杆control lever变速杆stick shift(gear shift lever)（副变速器）变速杆range selector变速叉shifting fork (gear shift fork)分动箱控制杆transfer gear shift fork变速踏板gear shift pedal变速轨（拨叉道轨）shift rail直接变速direct change(direct control)方向盘式变速column shift (handle change)按钮控制finger-tip control槽导变速gate changeb248b24807-09-08 12:23 空档位置neutral position直接驱动direct drive高速档top gear(high gear)低速档bottom gear(low speed gear)第一档first gear第二档second gear超速档overdirve gear经济档economic gear倒档reverse gear爬行档驱动特性drive performance反拖特性coast performance定输入扭矩特性constant input torque performance全油门特性full throttle performance寄生损失特性no load (parasitic losses)performance 原始特性primary characteristic响应特性response characteri stic吸收特性absorption characteristic全特性total external characteristic输入特性characteristic of enhance输出特性characteristic of exit力矩特性torque factor(coefficient of moment) 过载系数overloading ratio变矩系数torque ratio能容系数capacity factorr几何相似geometry similarity运动相似kinematic similarity动力相似dynamic similarity透穿性transparency万向节和传动轴universal joint and drive shaft万向节universal joint非等速万向节nonconstant velocity universal joint 等速万向节constant velocity universal joint准等速万向节near constant velocity universal joint 自承式万向节self-supporti ng uni versal joint非自承式万各节non self suporting universal joint回转直径swing diameter等速平面constant velocity plane万向节夹角true joint angle十字轴式万向节cardan (hookes)universal joint万向节叉yoke突缘叉flange york滑动叉slip yoke滑动节，伸缩节slip joint花键轴叉slip shaft yoke轴管叉（焊接叉）tube(weld yoke)十字轴cross(spi der)十字轴总成cross assembly挠性元件总成flexible universal joint球销式万向节flexible member assembly双柱槽壳housing球环ball球头轴ball head球头钉button中心球和座centering ball and seat球笼式万向节rzeppa uni versal joint钟形壳outer race星型套inner race保持架cage可轴向移动的球笼式万向节plunging constant vel ocity joint筒形壳cylinder outer race柱形滚道星形套inner race withcylinder ball grooves 偏心保持架non-concentric cage滚动花键球笼式万向节ball spline rzeppa universal joint外壳outer housing内壳体inner housing球叉式万向节weiss universal joint球叉ball yoke定心钢球centering ball三球销万向节tripod universal joint三柱槽壳housing三销架spider双联万向节double cardan universal joint凸块式万向节tracta universal joint凸块叉fork yoke榫槽凸块tongue and groove couplijng凹槽凸块groove coupling传动轴drive shaft(propeller shaft)传动轴系drive line传动轴形式drive shaft type两万向节滑动的传动轴two -joint inboard slip ddiveshaft 两万向节外侧滑动传动轴two joint ouboard slip drive shaft 单万向节传动轴single joint coupling shaft组合式传动轴unitized drive shaft传动轴减振器drive shaft absorber传动轴中间轴承drive shaft center bearing传动轴管焊接合件weld drive shaft tube assembly 传动轴特征长度drive shaft length传动轴谐振噪声resonant noi se of rive shaft传动轴的临界转速critical speed of drive shaft传动轴总成的平衡balance of drive shaft assembly 允许滑动量slip相位角phase angle传动轴安全圈drive shaft safety strap驱动桥drive axle(driving axle)类型type断开式驱动桥divided axle非独立悬架式驱动桥rigid dirve axle独立悬架式驱动桥independent suspensi on drive axle转向驱动桥steering drive axle贯通式驱动桥tandem axles“三速”贯通轴"three-speed" tandem axles单驱动桥single drive axle多桥驱动multiaxle drive减速器reducer主减速器final drive单级主减速器single reduction final drive双级主减速器double reduction final drive前置式双级主减速器front mounted double reducti on final drive后置式双级主减速器rear mounted double reduction final drive上置式双级主减速器top mounted double reducton final drive行星齿轮式双级主减速器planetary double reducti on final drive贯通式主减速器thru-drive双速主减速器two speed final drive行星齿轮式双速主减速器two speed planetary final drive双级双速主减速器two speed double reducti on final drive轮边减速器wheel reductor(hub reductro)行星圆柱齿轮式轮边减速器planetary wheel reductor行星锥齿轮式轮边减速器differential geared wheel reductor(bevelepicyclick hub reductor) 外啮合圆柱齿轮式轮边减速器spur geared wheel reductor差速器differential锥齿轮式差速器bevel gear differential圆柱齿轮式差速器spur gear differential防滑式差速器limited -slip differential磨擦片式自锁差速器multi-disc self -locking differential凸轮滑滑块自锁差速器self-locking differential with si de ring and radial cam plate 自动离合式自锁差速器automoti ve positive locking differential强制锁止式差速器locking differential液压差速器hydraulic differential轴间差速器interaxial differential差速器壳differential carrieer(case)主降速齿轮final reduction gear驱动轴减速比axle ratio总减速比total reduction ratio主降速齿轮减速比final reduction gear ratio双减速齿轮double reduction gear差速器主齿轮轴differential pinion-shaft差速器侧齿轮differential side gear行星齿轮spider gear(planetary pinion)螺旋锥齿轮spiral bevel gear双曲面齿轮hypoid gear格里林齿制gleason tooth奥林康型齿制oerlikon tooth锥齿轮齿数number of teeth in bevel gears and hypoid gears锥齿轮齿宽face width of tooth in bevel gears and hypoi d gears 平面锥齿轮plane bevel gear奥克托齿形octoid form平顶锥齿轮contrate gear齿面接触区circular tooth contact齿侧间隙backlash in circular tooth差速器十字轴differential spider差速器锁止机构differential locking -device差速器锁止系数differential locking factor差速器壳轴承carrier bearing桥壳axle housing整体式桥壳banjo housing可分式桥壳trumpet-type axle housing组合式桥壳unitized carrier-type axle housing对分式桥壳split housing冲压焊接桥壳press-welding axle housi ng钢管扩张桥壳expanded tube axle housing锻压焊接桥壳forge welding axle housing整体铸造式桥壳cast rigid axle housing半轴。
