毕设论文 店酒高层酒店建筑给水、排水及消防工程
- 格式:doc
- 大小:2.04 MB
- 文档页数:67
君如高层建筑给水排水及消防系统设计第一章设计任务及设计资料本设计的选题是长沙君如大厦建筑给水排水及消防工程设计,设计内容包括建筑给水,建筑排水,建筑消防,建筑热水以及附属设备和配件的选择。
在严格遵守规范和借鉴各位老师的设计经验的前提下,本设计较好地完成了以上的设计要求,并且通过技术经济比较,确定了这套最优方案。
由于缺乏设计经验,接触实际工程的机会少,所以设计中难免有错误和不妥之处,希望各位老师能够给予批评和指正。
1.1设计任务根据建设单位的要求,完成沈阳光明酒店建筑给排水及消防工程设计。
该综合楼要求设置完善的给水排水卫生设备和集中热水供应系统,其中热水供应系统全天24h满足客房供水。
该建筑立足于自救,要求设置独立的消火栓系统和自动喷洒系统;每个消火栓均设有消防按钮,消防时可直接启动消防泵。
生活给水泵要求自动启动。
此外,由于美观方面的考虑,管道均尽量暗设。
要求设计的该建筑的给水排水工程的各分项工程为:(1)建筑给水系统设计(包括冷水和热水系统);(2)建筑消防系统设计(包括消火栓系统,喷洒灭火系统)设计;(3)建筑排水系统设计;(4)建筑雨水排水系统设计。
1.2设计依据1.2.1建筑设计资料长沙市君如大厦,是一座综合楼,框架结构总建筑面积为22218㎡,建筑总高度为64.6m。
地上十八层,地下一层,地下一层为设备用房及地下停车场,二层~八层为办公用房,九~十八层为宾馆客房及办公用房。
屋面为电梯间和水箱间。
提供建筑物所在地的总平面图,各层的建筑平面图。
各层层高如下:地下1层为5.6m,地上1层为4.5m,2-8层为3.2m,9-18层为3m。
1.2.2相关设计资料(1) 给水条件该建筑以城市给水管网为水源,室外给水管道有两条,一条来自建筑南面一条来自建筑背面,两条平行给水管道分别距建筑墙体15m,接管点埋深1.5m,管径为100mm,管材为铸铁管,常年提供的资用水头为0.14Mpa。
最冷月平均水温为7℃,城市管网不允许直接抽水。
摘要我的毕业设计是沈阳某宾馆的建筑给排水设计。
建筑高度62.1m,总占地面积3538m2。
此建筑地上17层,地下1层。
本次设计需要完成建筑给水系统、建筑排水系统、建筑消防系统(消火栓给水系统及自动喷水灭火系统)、建筑屋面雨水排水系统设计。
给水系统采用分区供水,低区一到四层,由市政管网直接供水;高区五到十七层,采用变频泵供水。
排水系统采用污、废水合流制,底层单独排放,设专用通气立管。
消防系统分消火栓给水系统和自动喷水灭火系统,其中消火栓系统采用水泵高位水箱联合供水。
屋面雨水排水系统采用内排水。
给水管采用PP-R管;排水管采用铸铁管;消防系统均采用钢管。
关键词:高层建筑;给水系统;排水系统;消防系统AbstractMy graduation design is a hotel in Shenyang, the building water supply and drainage design.Building height of 62.1 m, the total area of 3538 m2. The building 17 layers on the ground, underground layer 1.The design needs to be done building water supply system, building drainage system, building fire control system (fire hydrant water supply system and automatic sprinkler system), the roof rainwater drainage system design.Water supply system using zoning, low negative a layer to the four layer, by the municipal water supply pipe network directly;high five to eleven layer, adopt the frequency conversion water supply pump. Drainage system using sewage, waste water sewage system, the separate discharge, set specific vent stack. Fire protection system of fire hydrant system and automatic sprinkler system, fire hydrant system uses the pump head tank joint water supply. Roof rainwater drainage system with internal drainage.For the use of PP-R pipes; pipe using iron pipe; steel tubes are used for fire system.Key words:high-rise building; water supply system; drainage system; fire protection system目录第1章绪论 (1)1.1 概况 (1)1.2 设计任务和设计内容 (1)1.3 设计依据和原始资料 (2)第2章设计方案的拟定 (4)2.1 给水系统 (4)2.2 热水系统 (7)2.3 消防系统 (8)2.4 排水系统 (11)第3章管道布置及设备安装要求 (13)3.1 给水管道布置与设备安装要求 (13)3.2 排水管道布置及设备安装要求.......... 错误!未定义书签。
摘要该建筑为宾馆,建筑高度为50.7米,总建筑面积约1.0万平方米。
本建筑物所有给水排水均按高层建筑给排水要求进行设计。
结合实际情况,根据建筑物的性质,用途,和室内设有完善的给水排水卫生设备,具体的给排水系统设计如下:给水系统:本建筑地下一层至地上二层由室外市政管网直接供水,三至十三层设有变频调速系统和水泵、屋顶水箱相接合的给水方式;由于消火栓超过十个,需设两条引入管。
.既保障了供水安全,又节约了能耗。
排水系统:本设计采用污废水合流排放体制。
管材采用了具有消声功能的螺旋UPVC排水管,升顶通气方式,为此可进一步提高环境质量。
地下室内消防电梯井旁、泵房地面均设有集水坑和废水提升装置。
消防系统:该建筑防火等级属于中危险级Ⅱ级,设计内容包括消火栓系统,自动喷淋和水幕系统。
在屋顶水箱间内设实验用消火栓装置,消火栓给水管网呈环状布置,各消火栓箱内设消防水泵启动电钮,能直接启动消防泵;室外设地下式水泵结合器,保证消防安全可靠。
商场,走廊,办公间,电梯前室设闭式自动喷淋系统,自动扶梯旁的防火卷帘处设置水幕系统。
热水系统:客房采用集中热水供应.各系统中的立管设在管井内或沿墙敷设,水平管根据各系统的特点明敷或暗敷。
本设计以经济、环保、节能为原则,通过借鉴以前的设计方法和经验,采用了合理的技术措施,使设计的各个系统达到了很好的使用效果。
关键词:给水;排水;消火栓;自动喷淋。
AbstractThis building is the large-scale market, the construction is highly 50.7 meters, total floor space approximately10,000 square meters. This building possesses for water draining water presses the high-rise construction to request for draining water to carry on the design. Unifies the actual situation, according to the building nature, the use, is equipped with the consummation with the room in for the water draining water sanitary equipment, concrete gives the drainage system design to be as follows:For aqueous system:This construction underground to ground two by outdoor municipal administration pipe network direct water supply, three to thirtent gives the square water pitcher type which is equipped with the frequency conversion velocity modulation system and the water pump, the roof water tank joins; Because the fire hydrant surpasses ten, must suppose two lead-in tubes. Both has safeguarded the water supply security, and saved the energy consumption.Drainage system:This design uses the dirt waste water confluence emissions system. The tubing used had the noise elimination function screw UPVC discharge pipe, rose to go against the ventilation way, might further improve the environment quality for this. In the basement nearby the fire electricity stairwell, the pump house ground are equipped with the sump and the waste water lifting gear.Fire prevention system:This building fire protection rank belongs to the dangerous levelⅡThe level, the design content including the fire hydrant system, sprays automatically with the water curtain system. In supposes the experimental fire hydrant installment in the roof water tank between, the fire hydrant service pipe net assumes the ring-like arrangement, in various fire hydrants box supposes the fire pump to start the push-button, can the line start fire extinguishing pump; Room peripheral equation below water pump coupler, guarantee fire prevention safe reliable. The market, the corridor, the work, in front of the elevator the room supposes the closed type to spray the system automatically, nearby escalator fire protection volume curtain place establishment water curtain system.Rain water system:This building is the large-scale market, is located in the city lively heartland, therefore sets up the surface request to the construction to be high, the construction roofing height dropping variance compares the death of a parent mainly to use in the rain water to drain water the way, as well as few outside drains water.Hot water system:Because this system water used only includes in the market the service personnel and the work personnel drinks the boiling water, therefore only supposes the electricity boiling water heater. The guest room uses the centralized hot water supply.In various systems pipe riser is located in the tube well or along the wall placing, the horizontal tube acts according to various systems to point out especially spreads or spreads darkly.This design take the economy, the environmental protection, the energy conservation as a principle, through profits from beforehand design method and the experience, has used thereasonable technical measure, enabled the design each system to achieve the very good use effect.Key word: for water ;Draining off water ;The fire hydrant ;Spurting voluntarily pours .引言近年来,随着我国经济实力的增强,生活水平的提高,人们对生活质量,特别是生活空间居住环境的要求也在日益提高。
某高层宾馆建筑给排水设计——毕业设计某高层宾馆建筑给排水设计摘要本文主要介绍了某高层宾馆的建筑给排水的设计。
主要包括给水系统、排水系统、消防系统、热水系统和雨水系统。
给水系统包括用水量的计算、给水分区的选择和管道的水力计算。
排水系统包括排水管的水力计算、通气管的设计和排污泵的选择。
消防系统包括消防用水量的计算、消防分区的划分、管道水力计算和消防泵的选择。
热水系统包括热水用水量、热媒量计算、加热器和循环泵的选择、管网水力计算。
雨水系统包括雨水量计算和雨水管布置方案。
本文具体分为给排水设计说明、给排水设计计算、致谢和参考文献四个部分。
关键词:给水系统;消防系统;热水系统;排水系统;雨水系统The Water-Supply and Drainage Engineering of A High-RiseHotelStudent’s name: Hades Huang Advisor: Li Lan(School of Civil Engineering Zhejiang University of Science and Technology)AbstractThis paper introduces the design that the water-supply and drainage engineering of a high-rise hotel. Including water-supply, drainage systems, fire fight systems, hot water-supply systems and rain water systems. Water –supply system, including thecalculation of water consumption, the choice of water-supplydistrict and pipeline hydraulic calculation. Drainage systems includingthe hydraulic calculation of drain, the tube design and the choice ofthe sewage pump. Fire fight system, including the calculation of thefire water, the division of the fire Service Division, the hydraulic calculation of pipeline and the choice of fire pump. Hot water-supply system, including the calculation of the hot water consumption and the amount of heat medium, heater and circulating pump selection, pipe network hydraulic calculation. Stormwater system, including the calculation of stormwater and rain water pipe lay out. This paper is divided into specific note to the drainage design, thank the rain sewage, reference of four parts.Key words: Water supply-system;Fire fight system;Hot water-supply system;drainage system; Rain water system目录摘要 (I)Abstract (II)1设计说明书 ............................................... 1 1.1工程概况 ..................................................... 1 1.2给水系统设计 (1)1.2.1给水方案选择 ..................................................................... .. (1)1.2.2给水方案选择依据 ..................................................................... (1)1.2.3给水方案的确定 ..................................................................... . (2)1.2.4给水附件 ..................................................................... . (2)1.2.5生活水泵和泵房 ..................................................................... ................ 2 1.3消火栓给水系统 (3)1.3.1消火栓给水系统说明 ..................................................................... .. (3)1.3.2消火栓给水系统的组成 ..................................................................... . (3)1.3.3消防管道布置 ..................................................................... .. (4)1.3.4消火栓布置 ............................................................................................. 4 1.4自动喷水灭火系统 (4)1.4.1自动喷水灭火系统说明 ..................................................................... . (4)1.4.2自动喷水灭火系统的组成 .....................................................................41.4.3自动喷水灭火系统的喷头布置形式 ..................................................... 5 1.5热水系统设计 (5)1.5.1热水设计说明 ..................................................................... .. (5)1.5.2热水系统组成 ..................................................................... .. (5)1.5.3热水系统附件 ..................................................................... .................... 5 1.6排水系统设计 (6)1.6.1排水系统的组成 ..................................................................... . (6)1.6.2排水管道类型 ..................................................................... .. (6)1.6.3排水管道的布置和敷设 ..................................................................... . (6)1.6.4通气管的设置 ..................................................................... .................... 6 1.7雨水排水系统设计 (7)2 给水系统设计计算 ......................................... 8 2.1给水系统分区 ................................................. 8 2.2用水量计算 (8)2.2.1最高日用水量 ..................................................................... .. (8)2.2.2最高日最大时用水量 ..................................................................... ........ 9 2.3生活水箱设计计算 ............................................. 9 2.5室内给水管网水力计算 .. (9)2.5.1计算公式 ..................................................................... . (9)2.5.2管径确定 ..................................................................... .. (10)2.5.3下区给水管网水力计算 ..................................................................... .. 102.5.4上区给水管网计算 ..................................................................... . (13)3消火栓系统设计计算 ...................................... 17 3.1消防用水量 .................................................. 17 3.2消火栓系统设计计算 (17)3.2.1消火栓间距 ..................................................................... . (17)3.2.2消防管道水力计算 ..................................................................... . (19)4自喷系统设计计算 ........................................ 21 4.1系统分区 .................................................... 21 4.2设计基本数据 ................................................ 21 4.3水力计算 .................................................... 21 4.4消防水箱、贮水池计算 . (27)4.4.1消防水箱计算 ..................................................................... (27)4.4.2消防水池计算 ..................................................................... (27)5热水系统设计计算 ........................................ 28 5.1热水用水量计算 .............................................. 28 5.2热媒量计算 .................................................. 29 5.3加热器容积计算 . (29)5.4盘管加热面积 (30)5.5膨胀罐设计计算 (30)5.6室内热水管网水力计算 (31)6排水系统设计计算 (33)6.1排水定额和设计秒流量的计算 (33)6.1.1排水定额 ..................................................................... .. (33)6.1.2设计秒流量 ..................................................................... . (33)6.2排水管道设计计算 (34)6.3排水管水力计算 (35)6.4通气管道设计计算 (37)6.5排污泵设计计算 (37)7雨水系统设计计算 (38)7.1雨水量设计计算 (38)7.1.1雨水量计算 ..................................................................... . (38)7.1.2雨水管的确定 ..................................................................... .................. 38 致谢 .................................... 错误~未定义书签。
关于高层建筑给排水消防设计【摘要】鉴于高层建筑结构自身具有的特殊性能,高层建筑给排水和消防设计将对人们的生命及财产安全有着直接性的作用及巨大影响,同时这也是对高层建筑质量进行审核的一个重要标准。
文章针对目前高层建筑给排水系统中潜存的一些问题及设计准求开展相关论述,主要针对高层建筑的给排水消防设计提供相关建议,望能够有一定的参考价值。
一、高层建筑给水系统的设计1.1给水管道设备的选择在挑选给水管道设备材料方面,一般情况下,我们会从压力、温度、安装形式、使用情况等多种途径做出综合全而的考虑,可以选择与当下高层建筑工程最为适合的给水管道设备与施工材料。
在高层建筑当中,给水管道设备材料的选择一般都会使用塑料管和钢塑复合给水管,塑料管和钢塑复合给水管不管是从材料质量、还是耐压强度、耐腐蚀性能上与以往的给水管道相比具有显著的优势,目前已经获得大众的认可及广泛使用。
1.2给水方式的确定在进行给水方式的确定上,我们可以从分配布局方面进行分析:第一,从分配布局的情况对卫生间、厨房进行科学分布设计,这是需要提前考虑的问题。
在经过给水方式设计之后如果有问题出现,那么给排水设计工作人员是需要承担相关责任的。
在确定给水方式的时候,是根据建筑专业布置的卫生间与厨房来进行设计,给排水专业有责任也有义务跟建筑方及时的进行沟通,这样才能够确保卫生间与厨房的设置保证美观与实用。
所以,一定要最大程度上改变设计师及相关设计工作人员的思想认识,从卫生间、厨房的具体性能入手,来进行卫生间与厨房的正确合理的布置,要做到前期的介入准备工作,便于挑选适合的给水方式。
1.3科学设置给水竖向分区高层建筑通常要比一般的建筑物高一些,可是如果仅利用外围管网提供的压力进行供水的话是远远不够的,达不到高层建筑的用水水压的实际要求,所以,为促使水压得到显著程度的提升,在具体的工程作业当中通常会利用增压设备来进行供水。
高层建筑一般六层或者七层划分为一个给水分区,其中,给水支管压力不宜高出0. 2MPa, 一旦超出,可以在支管上设置支管减压阀来降低水压。
建筑给排水酒店设计摘要范文酒店作为人们出行住宿、休闲娱乐的重要场所,其建筑给排水设计至关重要。
这就好比给酒店打造一套“血管”和“泌尿系统”,既要保证水流畅通无阻地供应到各个角落,又要高效地把废水排出去,还得保证整个过程安全又卫生。
一、设计概述。
在这个酒店的给排水设计中,我们首先得考虑水源的接入。
水源就像是酒店的生命之源,要确保它能持续稳定地供应。
根据酒店的规模和预计客流量,合理确定进水管的管径和数量,就像根据一个人的饭量来决定饭碗的大小一样。
二、供水系统。
1. 生活用水。
对于客房部分,我们得保证每个房间的水龙头出水量合适,水温稳定。
就像住客想要洗个舒服的热水澡,不能一会儿热得像在蒸桑拿,一会儿又冷得像掉进冰窖。
所以,热水供应系统采用了集中供热的方式,通过高效的热交换器,把热水快速送到各个客房。
在酒店的餐厅、厨房区域,用水需求又不一样。
这里需要大量干净、卫生的水来洗菜、洗碗等。
我们专门设置了大容量的供水管道,还安装了水质净化设备,毕竟谁也不想在餐厅里吃到用脏水洗过的菜呀。
2. 消防用水。
消防可是酒店安全的重中之重。
就像给酒店穿上了一套防火的铠甲。
消防用水系统包括消火栓系统和自动喷水灭火系统。
消火栓的位置设置得很巧妙,要保证在酒店的每个区域都能在紧急时刻方便取用,就像在城堡里到处设置了防御的武器一样。
自动喷水灭火系统则像一个个隐藏的小卫士,一旦有火灾发生,温度升高,喷头就会自动喷水,把火灾扼杀在萌芽状态。
三、排水系统。
1. 污水排放。
客房的污水主要来自卫生间,这些污水又脏又臭,得尽快排走。
我们设计了合理坡度的排水管道,让污水像坐滑梯一样迅速流到污水处理设施。
在厨房区域,因为有很多油脂,所以排水管道还特别做了隔油处理,不然油脂堵住管道,那就像人的血管被堵住一样,会引发大问题。
2. 雨水排放。
酒店的屋面面积比较大,下雨天雨水就像洪水一样涌来。
我们采用了有组织的雨水排放系统,把雨水收集起来,一部分可以用于酒店的景观浇灌等,就像把天上掉下来的“免费水”合理利用起来,既环保又省钱。
高层酒店及商场给排水设计摘要:本文通过对某酒店商场给排水设计的实践总结,介绍该建筑的给水供水系统、热水供水系统、污水排水系统、雨水排水系统、消火栓系统、自动喷淋系统和大空间主动喷水灭火系统设计,为大型酒店商场类综合性建筑给排水设计提供参考。
关键词:高层酒店商场给排水消防设计中图分类号:s611 文献标识码:a 文章编号:工程概况本工程为某博览交易中心,位于江门市江海区。
总建筑面积338763.7平方米,地上部分面积约为229924㎡,地下部分面积约为108839.7㎡。
地下两层,负二层主要为停车场及设备房(水泵房、风机房),负一层为商业及设备房(变配电房、消防控制中心),地上部分裙楼 6 层,塔楼 21 层,裙楼均为商业,塔楼6层至21层为酒店,总建筑高度95.75m,属于一类高层综合建筑。
本工程的设计内容包括:给水供水系统、热水供水系统、污水排水系统、雨水排水系统、消火栓系统、自动喷淋系统和大空间主动喷水灭火系统。
生活给水系统1.水源本工程将从市政供水管网中接一根dn200的管道作为本大楼的水源,供水压力为0.3mpa。
2.系统由于商业部分与酒店部分分开产权,为了方便管理,两部分的给水系统是独立分开的,生活泵房也分开设置。
2.1系统分区商业竖向分为两个供水区:低区包括-2~3层,市政直接供水;中区包括4~7层(共4层),加压供水。
酒店竖向分为两个供水区:中区包括6~11层(共6层),加压供水f;高区包括 12~21f(共10层),加压供水,其中12~16层(共5层)集中减压,17~21层(共5层)不减压。
2.2系统选择商业及酒店均采用生活水池加全自动变频给水设备联合供水。
商业生活给水低、中区均为下行上给的给水方式;酒店生活给水中、高区均为上行下给的给水方式。
其中高区12~16层给水主管在16层集中减压后再分到每个房间的给水立管。
2.3用水量2.3.1. 商业-2~3层低区用水量计算表:2.3.2.酒店6~24层用水量计算表:2.4水池本建筑生活贮水池分商业生活水池与酒店生活水池,其容积均按其最高日用水量加10%的未预计水量和管网漏失量的和的20%确定,且均平分为两个独立的生活水池。
摘要本工程地下1层,地上15层,其中1-3层为娱乐城, 每层有公共卫生间若干,4层及以上为客房,建筑总高度59米。
本论文就该建筑给水排水工程进行了设计,主要内容包括给水系统,消防系统,排水系统和雨水系统。
其中给水系统中采用分区给水,低区采用市政管网直接供水,高区采用水池-水箱-水泵联合供水。
消防系统中包括有消火栓系统和自动喷水灭火系统,排水采用合流制排水,雨水采用重力内排水的方式,及时地将屋面雨水排出。
此外还包括了给水引入管,排出的水至室外化粪池,及贮水池,水泵房,高位水箱等方面设计。
本设计中给水干管和立管材均采用不锈钢管,其他支管均采用铸铁管;消火栓给水管采用热镀锌钢管,自动喷水灭火系统管道采用内外壁热镀锌钢管;排水管材采用铸铁管,水力计算按塑料管计。
关键词:高层酒店综合楼;给水系统;消火栓系统;自动喷水灭火系统;排水系统;雨水系统ABSTRACTThe construction of underground 1 floors, 15 floors on the ground, including 1-3 layers of entertainment city, each layer has a toilet several, more than 4 floors and rooms, building a total height of 59 meters.In this paper, the building water supply and drainage engineering for the design, the main content includes the water supply system,fire system, the drainage system and drainage system. Using the water where the water supply system, low zone by the municipal water supply pipe network directly, high using the pool - tank joint water supply - water pump. Fire control system including fire hydrant system and automatic sprinkler system, the use of drainage drainage system, rain water by gravity drainage way, will promptly roof rainwater discharge. In addition to the water inlet pipe, the water discharged to the outdoor septic tank, and tank, pump house, water tank etc.. Pipe anda vertical pipe are made of stainless steel pipe water dry in this design, the other branch pipe are made of cast iron pipe; firehydrant water supply pipe using hot galvanized steel pipe, the inner and outer wall of galvanized steel pipe sprinkler system piping; drainage pipe using iron pipe, hydraulic calculation according to the plastic tube gauge.KEYWORDS: Upper Room Hotel building; water supply system; fire hydrant system; automatic sprinkler system; drainage system; drainage system.目录摘要 (1)第一章设计任务及资料 (5)第二章建筑给水设计及计算 (6)2.1 给水系统分区 (6)2.2给水系统的组成 (7)2.3主要设计参数 (7)2.4给水管道布置与安装 (7)2.5室内给水系统计算 (8)2.6生活水池及消防水池计算 (9)2.7设计秒流量计算 (10)2.7.1II区给水立管计算 (15)2.8生活加压设别的选择 (19)第三章建筑排水系统的设计与计算 (20)3.1排水方式的选择 (20)3.2排水系统分区 (20)3.3排水系统的组成 (20)3.4排水管道及设备安装要求 (20)3.5住宅污水排水系统计算 (21)3.5.1客房污水横管管道计算 (21)3.5.2公共卫生间计算 (22)3.5.3客房污水立管管道计算 (23)第四章建筑消防给水系统设计与计算 (25)4.1消火栓系数 (25)4.1.1设计参数 (25)4.1.2消火栓系统的设计计算 (26)4.2消防水泵计算 (27)4.3水泵接合器 (28)4.4减压稳压消火栓 (28)4.5消防排水 (28)4.6消防水池计算 (29)第五章雨水系统的设计及计算 (29)5.1塔楼雨水部分设计计算 (29)5.2降雨强度 (29)5.3裙楼雨水部分设计计算 (31)第六章自动喷淋设计与计算 (31)6.1喷头流量 (31)6.2流速 (31)6.3水力坡降 (31)6.4沿程水头损失 (32)6.5局部损失 (32)6.6总损失 (32)6.7终点压力 (32)论 (43)参考文献…………………………………………………………………………………………………………44第一章设计任务及资料本工程地下1层,地上15层,其中1-3层为娱乐城, 每层有公共卫生间若干,卫生器具布置见平面图。
XXXX酒店建筑给水排水及消防系统设计摘要:本设计为XXXX酒店建筑给水排水及消防系统设计。
总建筑面积约为14270m2,建筑总高度为76.2m,地上二十二层,地下一层,地下一层为设备用房,一、二层为餐饮及办公用房,三~二十层为宾馆客房,二十一及二十二层为办公用房。
屋面为电梯间和水箱间。
设计主要包括对建筑内的给水排水工程以及与之配套的室内外部分给水排水工程的设计,具体包括:室内冷水系统、热水系统、消防系统、自动喷洒系统、排水系统以及雨水系统。
在给水系统的设计中,本设计采用分区给水的方式。
高、低区均采用变频调速泵供水及上行下给的供水方式,供水可靠性较好,节省能源。
该建筑为高层宾馆综合大楼,按照高层民用建筑防火规范,消火栓宜布置在明显、经常有人出入且使用方便的地方,因而在该建筑的房间走廊中,电梯的前室以及地下室中均布有消火栓。
其中屋顶水箱应贮存火灾初期10min的消防水量。
该建筑危险等级为中危险级Ⅰ级,采用湿式自动喷水灭火系统,由湿式报警装置,闭式喷头和管道等组成。
热水系统采用全循环的系统,高区低区均为上行下给的布置形式。
最不利点水温大约为60℃,管道中水温在60℃~70℃之间。
本建筑的生活污水采用分流制排放。
雨水采用内排水系统,生活污水经化粪池处理后排放到市政污水管网,餐饮污水经隔油池处理排放到市政污水管网。
雨水设专门的雨水立管排入市政雨水管道。
在设计过程中,主要的依据是建筑给水排水设计规范、高层民用建筑设计防火规范、建筑设计防火规范,自动喷水灭火系统设计规范等。
关键词:高层建筑;分区给水;分流制ABSTRACTThis design is for a mansion called Guang Ming located in Shenyang. The total area of the architecture a is 14270 square meters,the total height is 76.2 meters,There are 22 floors on the ground,the floor underground is equiPment room,the 1 and 2 floors is dining room and office,3~20 floors are hotel,21~22 floors are office.The design mainly includes the water suPPly system,the drainage system indoor and match with which outside. The design in detail includes indoor water suPPly system,hot water system,fire fighting system ,auto-sPrinkle system,sewage system and storm drainage system.The design of water suPPly system adoPted seParate water suPPly. High and Low sections all use the mean of Frequency Control PumP to suPPly water. The system suPPly water from bottom to toP. This system is energy saving,and the security is good.The building is high,according to the high Public building fire Prevention standards; the fire hydrant of interior is required on the Place that can be used facility,so all of the hydrants of this building are Put besides the staircase and also in the cellar. The water tank ought to be keP t in storage of 10min’s fire fighting water. The auto-sPrinkle system is distinguishing a fire to the damP style in adoPting the wet style to distinguish a fire. As to can not use adoPt gas to distinguish fire the unit inner Place fire hydrant and the building that sPrinkles voluntarily.Warm water system adoPts comPletely circulatory system. High section is suPPlied from bottom to toP. The temPerature of the list of all Points must be about 60℃. The temPerature of water in PiPe needs to be 60℃-70℃.The architecture adoPts interflow for draining water. The rainwater adoPts the indePendent drainage systems,the excrement,urine and sewage are dialed with the sePtic tank before discharge into municiPal network. There are sPecial rainwater PiPe in charge of discharging rainwater into the municiPal rainwater net.In designing Process,chiefly based on The SkyscraPer Water SuPPle And Drainage Design SPecification、SkyscraPer Fire Prevention Norm Design SPecification、Automatic SPray Design SPecification、An Hard Polyvinylchloride PiPeline Design SPecification of Building Water SuPPly And Drainage.Keywords:high-level architecture;seParate water suPPly;convergence bridging system目录第一章设计任务及设计资料 (1)1.1设计任务 (1)1.2设计依据 (2)1.2.1建筑设计资料 (2)1.2.2相关设计资料 (2)1.2.3设计规范 (2)第二章方案设计说明 (4)2.1建筑给水工程 (4)2.1.1系统的选择 (4)2.1.2系统的组成 (4)2.2建筑排水工程 (4)2.2.1系统的选择 (4)2.2.2系统的组成 (5)2.3建筑消防给水工程 (5)2.3.1系统的选择 (5)2.3.2系统的组成 (7)2.4建筑热水工程 (7)2.4.1系统的选择 (7)2.4.2系统的组成 (8)2.5管道和附件的安装 (8)2.5.1给水管道安装要求 (8)2.5.2排水管道安装要求 (8)2.5.3消防给水管道安装要求 (9)2.5.4热水管道及设备安装要求 (9)第三章建筑给水排水设计计算 (11)3.1生活水箱、消防水池、消防水箱容积计算 (11)3.1.1生活水箱容积的计算 (11)3.1.2消防水池容积的计算 (13)3.1.3消防水箱 (13)3.2建筑给水系统计算 (14)3.2.1用水定额及用水量计算 (14)3.2.2给水管网水力计算 (14)3.3建筑排水系统计算 (24)3.3.1排水系统计算 (24)3.3.2屋面雨水排水系统计算 (40)3.4建筑消防系统计算 (41)3.4.1设计计算 (42)3.4.2消防管道系统计算 (43)3.4.3自喷管道系统计算 (46)3.5 建筑热水系统计算 (49)3.5.1耗热量计算 (49)3.5.3 常用设备的选择 (49)3.5.3蒸汽管道的计算 (50)3.5.4配水管网的水力计算 (50)3.5.5热水管网热损失及循环流量的计算 (67)3.5.6循环水泵的选择 (73)第四章技术经济分析 (74)4.1建筑给水工程 (74)4.2建筑排水工程 (74)4.3建筑热水工程 (74)4.4建筑消防工程 (74)致谢 (75)参考文献 (76)第一章设计任务及设计资料随着中国加入世界贸易组织,我国的建筑业面临着巨大的机遇和挑战。
康乐县某住宅楼室内给排水及消防设计目录摘要第一章设计说明 (4)第二章设计任务书 (5)第三章给水计算 (7)第四章排水计算 (15)第五章消防计算 (21)摘要关键词:给水排水消防我们开了这半学期的城市给水排水课程,学习到关于基本的建筑给水排水规划基本原理及相关知识。
本次实习是我们专业在大学学习阶段中重要的实践教学环节。
通过本次实习,使我在所学的各类课程的基础上,了解该专业在建设工程中的地位、作用和社会需求。
通过本次实习确实有学到了许多知识,并且对书本知识有了更加深刻的理解和体会,这期课设任务不只是对给水排水规划的知识学习,还有一些所用到的以前学的知识得以复习。
比如在制图时,把自己学到的CAD知识用到实际中;在编排word 文档时,有更深的了解了其中的知识。
最后依照指导老师要求,完成了本次实习各项内容的总结,各种信息的汇总,对在此次实习中了解调查到的知识点进行了归纳。
.为了很好的完成给水排水工程设计任务,应了解:研究设计任务的内容,弄清本工程的规划设计范围和具体要求,然后进行翔实的基础资料调查。
We opened this half of the urban water supply and drainage course, learn about the basic building water supply and drainage planning basic principle and relevant knowledge. This practice is our professional in the stage of the university to study important practical teaching link. Through this internship, I learned in all kinds of courses, on the basis of understanding the professional in the position and role of the construction project and social needs.Through this internship really have learned a lot of knowledge, and the book knowledge, with a more profound understanding and experience, this class set tasks not only the knowledge of water supply and drainage planning study, and some used to review previously learned knowledge. Such as in the drawing, use oneself learns knowledge of CAD in actual; In the time in the word document has a deeper understanding of the knowledge of them. Finally according to the guiding teacher asked, completed the internship each content summary, summary of information, know about in the practice of the survey to the knowledge induction..In order to good for water supply and drainage engineering design tasks, should understand: the research contents of design tasks and find out the planning and design of the project scope and specific requirements, and then on the basis of abundant materials.第一章设计说明本建筑为物达商住楼,建筑所在地形较平坦,有较充足的水源,居民生活水平较高,有良好的供水设施和排水设施。
酒店高层酒店建筑给水、排水、消防工程毕业设计前言本工程项目是高层酒店建筑给水、排水、消防工程的设计计算。
该高层建筑位于吉林省长春市,是一栋以办公为主体含有宾馆、餐饮、洗浴的综合性高层建筑。
建筑物总高度46米,总面积为231059m,主楼是十五层建筑,并且还含有地下一层。
根据设计资料及设计要求,给水系统采用并联水泵分区给水系统,分为:高区(十二至十五层)、中区(七至十一层)、低区(半地下室至六层)。
根据本建筑物的特点,该工程排水系统采用:①单立管排水系统;②公共厨房与卫生间排水分开;③厨房排水单独排出,集中除油处理再排放;④地下室消防电梯机坑、泵房、消防、洗浴等处设集水坑,由潜污泵排出;⑤宾馆客房卫生间排水在设备层(技术夹层)集中后排出。
本设计消防系统与生活给水系统分开设置,消火栓系统与自动喷洒系统共同设计。
消火栓系统布置:保证三股进水(水泵进水,水泵结合器进水和水箱给水)畅通。
水箱给水高区与低区共用一条管线,在高区与低区的消防环之间设置减压阀减压保证低区水压。
自动喷洒系统布置:高区(十层至十九层)设置两个湿式报警阀,低区(地下一层至九层)设置三个湿式报警阀,即要保证三股进水的同时,还要保证所有进水要在湿式报警阀之前。
通过本工程项目设计,本人不但掌握了高层建筑的给水、排水、消防工程等设计的设计要点和设计内容,同时对工程制图有了更扎实的基本功。
关键词:给水工程;排水工程;消防工程;- I -- II -PrefaceThis designed project is the design of the water supply system, drainage system and fire fight system of the GuoShui office building in Changchun city. The building lies in Changchun city, Jilin provice, which is an integrated high-rise structure that accompanies with guest house, meal and drinking, bathing, and so on. The building is about 87 meters high, which is 31,059 square meters area. Its main floor is 21th layers, and the both sides are six layers, but also there are two layers underground.According to design data and request, water supply system is used shunt pump and zoning. There are three partitions: high zone (14th layer to 19th layer), mid zone (7th layer to 13th layer), low zone (underground layer to 6th layer).Based on the characteristic of the structure, there are five manners as following in the drainage system of the project: First, single standpipe drainage system. Second, public kitchen and toilet effluent is designed the independent drainage system. Third, kitchen wastewater is designed theindependent system, and centrially removed oil before it is discharged. Four, collecting sump is located in the underground fire elevator shoot, pumping room, fire control, bathing and so on, and the drain water is discharged by submerged pump. Five, the wastwater of guest room toilet is discharged after being collected in the equipment room (technique interlayer).Fire system and living water system are dividually set up. Fire cock system and automatic spraying system are commonly designed. The layout manners of fire cock system are as following: the arrangement of high area and low area guarantees well flowing of three strands inlet (pump inlet, pump adapter inlet, water tank inlet). High area and low area are used a pipeline by the water block- III -supply, the between of which is installed reducing pressure valve that assures the pressure of the low area. The layout manners of automatic spraying system are as following: the high area (10th layer to 19th layer) is installed two wet alarm valves, and low area (undergroud 1th layer to 9th layer) is installed three wet alarm valves. They guarantee well flowing of three strands inlet the same as they assure the trouble-free operation of all inlet water before the warning valves are started.Accoding to the design, I not only am proficient in the design points and the design contents of high buildings’water supply project, drainage project, fire fight project and so on, but also there is better the basic skill to the engineering drawing.Keywords: Water supply project; Drainage project; Fire fight project- IV -目录前言 (I)Preface (III)第1章设计概论 (1)1.1 设计题目 (1)1.2 设计目的 (1)1.3 设计范围 (1)1.4 原始资料 (1)1.4.1 工程概况 (1)1.4.2 土建资料 (2)1.4.3 城市给排水资料 (2)1.5 设计任务及要求 (2)1.5.1 方案选择及确定 (2)1.5.2 图纸绘制要求 (3)第2章设计水量计算 (5)2.1 生活水量计算 (5)2.2 消防水量计算 (8)2.2.1 消火栓水量计算 (8)2.2.2 消防水池与水箱计算 (9)2.3 生活水箱与消防水池,进水管确定 (9)第3章生活给水系统设计 (10)3.1 给水系统分区 (10)3.2 给水系统设计方案选择 (10)3.3 给水管网敷设原则 (11)3.3.1 给水管网室外敷设原则 (11)3.3.2 给水管网室内敷设原则 (11)3.4 给水系统水力计算 (12)3.4.1 高、中、低区给水系统水力计算 (12)3.4.2 低、中、高区水利计算表及水利计算图 (15)3.5 水泵确定 (23)3.5.1 高区水泵确定 (23)第4章排水系统设计 (25)- V -4.1 排水系统选择的原则 (25)4.2 排水系统敷设原则 (25)4.2.1 排水系统的敷设原则 (25)4.2.2 排水系统的敷设几个常见问题 (26)4.3 排水系统的水力计算 (27)4.3.1 排水系统水力计算依据 (27)4.3.2 排水水力计算表和水力计算图 (30)第5章消防系统设计 (46)5.1 消防系统分区 (46)5.1.1 建筑耐火等级 (46)5.1.2 消防系统分区原则 (47)5.2 消防系统给水方式 (49)5.3 消防系统布置 (49)5.3.1 消火栓系统布置原则: (49)5.3.2 消防系统布置 (50)5.4 消防系统水力计算 (50)5.4.1 消火栓系统计算 (50)5.5 消防系统水箱增压设备及减压阀计算 (56)5.5.1 消防水箱气压罐计算 (56)参考文献 (60)致谢 (61)- VI -第1章设计概论1.1设计题目某酒店给水排水、消防设计。
1.2设计目的毕业设计是在本科生学完教学计划所规定的全部课程后进行的最重要的也是最后一个实践性教学环节。
它可以使学生综合运用和深化所学的理论知识,并且较系统地、完整地将所学的专业知识应用于实际、培养学生独立分析与解决实际问题的能力。
使其受到工程师的基本训练。
它还能使学生,初步掌握专业工程设计的内容、基本要求、计算方法、设计步骤、绘图能力与某些技巧,为毕业后的专业工作奠定必要的基础。
毕业设计又是以前各教学环节的继续、深化、总结与检验提高的过程,其效果将直接影响毕业生的质量。
1.3设计范围高层建筑给水排水工程毕业设计范围包括:建筑内部给水、排水、消防,的方案选择、技术经济分析、工艺设计计算、施工图设计,还包括自选或指定专题设计内容。