下载文档原格式
JD120型技术参数表
合计功率为：18.2Kw/H JD160型技术参数表
合计功率为：26Kw/H JD90型技术参数表
合计功率为：15.5Kw/H 海天牌注塑机技术参数：
海天HTF86/TJ注塑机总功率为：13.7 Kw/H（86吨）
海天HTF160J/TJ注塑机总功率为：24.75 Kw/H（160吨）
海天HTF200J/TJ注塑机总功率为：32.75 Kw/H（200吨）
海天HTF250J/TJ注塑机总功率为：38.65 Kw/H（250吨）
注塑机生产电耗：油压机,机器前二个小时内为全负荷运作，二个小时后耗电量为额定功率的65%左右，电动机则为50%左右。
如果采用伺服电机会更省电，一般注塑机都是步进电机。
通过以上机器参数可以得出，80吨新注塑机一天的253度电（以最大功率机器计算），120吨新注塑机一天的约338度电（以最大功率机器计算），160吨新注塑机一天的约424度电（以最大功率机器计算）。
海天注塑机86T⾄1000T各机型参数海天注塑机86T⾄1000T各机型参数HTF86/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 36 40 45 螺杆长径⽐Screw L/D Ratio L/D 23.3 20 18.7 理论容量Shot Size(Theoretical) cm3173 214 270 注射重量Injection Weight(PS) g 157 195 246 注射压⼒Injection Pressure Mpa 197 160 126 螺杆转速Screw Speed rpm 0～195合模装置CLAMPING UNIT合模⼒Clamp Tonnage KN 1200移模⾏程Toggle Stroke mm 350拉杆内距Space Between Tie Bars mm 410x410最⼤模厚Max.Mold Height mm 430最⼩模厚Min.Mold Height mm 150顶出⾏程Ejector Stroke mm 120顶出⼒Ejector Tonnage KN 33顶出杆根数Ejector Number Piece 5 其它OTHERS最⼤油泵压⼒Max.Pump Pressure MPa 16油泵马达Pump Motor Power kw 11电热功率Heater Power kw 9.75外形尺⼨Machine Dimension(LxWxH) m 4.92x1.33x1.95重量Machine Weight t 4.56 料⽃容积Hopper Capacity kg 25油箱容积Oil Tank Capacity L 240HTF160J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 40 45 48 螺杆长径⽐Screw L/D Ratio L/D 22.5 20 18.8 理论容量Shot Size(Theoretical) cm3253 320 364 注射重量Injection Weight(PS) g 230 291 331 注射压⼒Injection Pressure Mpa 202 159 140 螺杆转速Screw Speed合模装置CLAMPING UNIT合模⼒Clamp Tonnage KN 1600移模⾏程Toggle Stroke mm 420拉杆内距Space Between Tie Bars mm 455x455最⼤模厚Max.Mold Height mm 500最⼩模厚Min.Mold Height mm 180顶出⾏程Ejector Stroke mm 140顶出⼒Ejector Tonnage KN 33顶出杆根数Ejector Number Piece 5 其它OTHERS最⼤油泵压⼒Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 15电热功率Heater Power kw 9.75外形尺⼨Machine Dimension(LxWxH) m 5.4x1.45x2.05 重量Machine Weight t 5.2料⽃容积Hopper Capacity kg 25油箱容积Oil Tank Capacity L 320HTF200J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 45 50 55 螺杆长径⽐Screw L/D Ratio L/D 22.2 20 18.2 理论容量Shot Size(Theoretical) cm3334 412 499 注射重量Injection Weight(PS) g 304 375 454 注射压⼒Injection Pressure Mpa 210 170 141 螺杆转速Screw Speed rpm 0～165合模装置CLAMPING UNIT合模⼒Clamp Tonnage KN 2000移模⾏程Toggle Stroke mm 470拉杆内距Space Between Tie Bars mm 510x510最⼤模厚Max.Mold Height mm 510最⼩模厚Min.Mold Height mm 200顶出⾏程Ejector Stroke mm 130顶出⼒Ejector Tonnage KN 62顶出杆根数Ejector Number Piece 9其它OTHERS最⼤油泵压⼒Max.Pump Pressure MPa 17.5 油泵马达Pump Motor Power kw 18.5电热功率Heater Power kw 14.25外形尺⼨Machine Dimension(LxWxH) m 5.3x1.6x2.1 重量Machine Weight t 6.8料⽃容积Hopper Capacity kg 50油箱容积Oil Tank Capacity L 390这个图跟我看过的宝源机的顶棍孔差不多。
海天注塑机86T至1000T各机型参数HTF86/TJHTF120J/TJHTF160J/TJHTF200J/TJ其它OTHERS最大油泵压力Max. Pump Pressure MPa 17.5 油泵马达Pump Motor Power kw 18.5电热功率Heater Power kw 14.25外形尺寸Machine Dimension(LxWxH) m 5. 3x1. 6x2. 1 重虽Machine Weight t 6.8 料斗容积Hopper Capacity kg 50油箱容积Oil Tank Capacity L 390HTF250J/TJ注射装置INJECTION UNIT A B C 螺杆直径Screw Diameter mm 50 55 60 螺杆长径比Screw L/D Ratio L/D 22 20 18. 3 理论容址Shot Size(Theoretical) 3 cm 442 535 636 注射重址Injection Weight(PS) g 402 487 579 注射压力Injection Pressure Mpa 205 169 142 螺杆转速Screw Speed rpm 0—180合模装宜CLAMPING UNIT合模力Clamp Tonnage KN 2500移模行程Toggle Stroke mm 540拉杆内距Space Between Tie Bars mm 570x570最大模厚Max. Mold Height mm 570最小模厚Min. Mold Height mm 220篠版侧面尺寸这个图跟我看过的宝源机的顶棍孔差不多。
顶出行程Ejector Stroke mm 130顶出力Ejector Tonnage KN 62 顶出杆根数Ejector Number Piece 9 其它OTHERS最大油泵圧力Max. Pump Pressure MPa 17.5 油泵马达Pump Motor Power kw 22电热功率Heater Power kw 16. 65外形尺寸Machine Dimension(LxWxH) m 6. 02x1. 7x2. 1 重虽Machine Weight t 8. 1 料斗容积Hopper Capacity kg 50油箱容积Oil Tank Capacity L 630複版正面尺寸HTF300J/TJ注射装宜INJECTION UNIT A B C 摞杆直径Screw Diameter mm 60 65 70 螺杆长径比Screw L/D Ratio L/D 21.7 20 18.6 理论容址Shot Size(Theoretical) 3 cm 727 853 989 注射重址Injection Weight(PS) g 662 776 900 注射压力Injection Pressure Mpa 213 182 157 摞杆转速Screw Speed rpm 0-185合模装迓CLAMPING UNIT合模力Clamp Tonnage KN 3000移模行程Toggle Stroke mm 600YET560_ 420_・ 280IS > i令一f♦♦♦44♦ +・! *r *200■400S TL、8-033拉杆内距Space Between Tie Bars mm 660x660最大模好Max. Mold Height mm 660最小模厚Min. Mold Height mm 250顶出行程Ejector Stroke mm 160顶出力Ejector Tonnage KN 62顶出杆根数Ejector Number Piece 13 其它OTHERS最大油泵圧力Max. Pump Pressure MPa 16 油泵马达Pump Motor Power kw 30电热功率Heater Power kw 19. 65外形尺寸Machine Dimension(LxWxH) m 6. 5x2. 0x2. 4 重址Machine Weight t 12.5 料斗容积Hopper Capacity kg 50油箱容积Oil Tank Capacity L 670HTF360J/TJ注射装宜INJECTION UNIT A B C 螺杆直径Screw Diameter mm 65 70 75 螺杆长径比Screw L/D Ratio L/D 21.5 20 18.7 理论容址Shot Size(Theoretical) cm' 1068 1239 1423 注射重址Injection Weight(PS) g 972 1127 1295 注射压力Injection Pressure Mpa 208 180 156 螺杆转速Screw Speed rpm 0-185合模装宜CLAMPING UNIT合模力 Clamp Tonnage KN 3600 移模行程 Toggle Stroke mm 660 拉杆内距 Space Between Tie Barsmm 710x710 最大模厚 Max. Mold Height mm 710 最小模厚 Min. Mold Height mm 250 顶出行程 Ejector Stroke mm 160 顶出力 Ejector Tonnage KN 110 顶出杆根数Ejector NumberPiece13其它 OTHERS最大油泵圧力 Max. Pump Pressure MPa 17.5 油泵马达 Pump Motor Power kw 37 电热功率 Heater Powerkw 24.85 外形尺寸 Machine Dimension(LxWxH)m 6. 9x2. 1x2. 5垂虽 Machine Weight t 15 料斗容积 Hopper Capacity kg 100 油箱容积 Oil Tank CapacityL922HTF450J/TJ注射装宜 INJECTION UNITABC螺杆直径 Screw Diameter mm 70 80 84 螺杆长径比Screw L/D RatioL/D 22.9 20 19 理论容址Shot Size(Theoretical)3 cm142418602050桓扳卞面尺好-艦-400 一注射重址Injection Weight(PS) g 1296 1693 1866 注射乐力Injection Pressure Mpa 201 156 141 螺杆转速Screw Speed rpm 0-155合模装置CLAMPING UNIT合模力Clamp Tonnage KN 4500移模行程Toggle Stroke mm 740拉杆内距Space Between Tie Bars mm 780x780最大模厚Max. Mold Height mm 780最小模厚Min. Mold Height mm 330顶出行程Ejector Stroke mm 200顶出力Ejector Tonnage KN 110顶出杆根数Ejector Number Piece 13 其它OTHERS最大油泵压力Max. Pump Pressure MPa 17.5 油泵马达Pump Motor Power kw 45电热功率Heater Power kw 29. 45外形尺寸Machine Dimension(LxWxH) m 7. 9x2. 3x3. 2 重虽Machine Weight t 19 料斗容积Hopper Capacity kg 100油箱容积Oil Tank Capacity L 1170HTF530J/TJ注射装宜INJECTION UNIT | | A B C D469HTF650J/TJHTF780J/TJ視版正面尺寸：卷8HTF900J/TJ* 1V i油泵马达Pump Motor Power kw 37+45 电热功率 Heater Powerkw 61. 15 外形尺寸 Machine Dimension(LxWxH)m 11. 3x2. 8x4. 0重址 Machine Weight t 46 料斗容积 Hopper Capacity kg 200 油箱容积 Oil Tank CapacityL1630HTF1000J/TJ注射装宜 INJECTION UNITABCD螺杆直径 Screw Diameter mm 100 110 120 130 螺杆长径比 Screw L/D Ratio L/D 24. 4 22 20.2 18.6 理论容量 Shot Size(Theoretical) cm' 3770 4562 5429 6371 注射重量 Injection Weight(PS) g 3131 4145 4940 5798 注射压力 Injection PressureMpa 211174146125螺杆转速 Screw Speedrpm0—101合模装宜 CLAMPING UNIT合模力 Clamp Tonnage KN 10000 移模行程 Toggle Stroke mm 1100 拉杆内距 Space Between Tie Barsmm 1090x1090最大模厚 Max. Mold Height mm 1100 最小模厚 Min. Mold Height mm 500 顶出行程Ejector Strokemm 320 顶出力Ejector TonnageKN215模版正面尺寸adass 12-03592-M24-7H：§215501400 1120 &80。
海天注塑机技术参数表
海天注塑机技术参数表
内容来源网络，由“深圳机械展（11万㎡，1100多家展商，超10万观众）”收集整理！
更多cnc加工中心、车铣磨钻床、线切割、数控刀具工具、工业机器人、非标自动化、数字化无人工厂、精密测量、3D打印、激光切割、钣金冲压折弯、精密零件加工等展示，就在深圳机械展.
内容来源网络，由“深圳机械展（11万㎡，1100多家展商，超10万观众）”收集整理！
更多cnc加工中心、车铣磨钻床、线切割、数控刀具工具、工业机器人、非标自动化、数字化无人工厂、精密测量、3D打印、激光切割、钣金冲压折弯、精密零件加工等展示，就在深圳机械展.。
海天注塑机86T至1000T各机型参数机械手相对安装计算方法：机械手LM-(注塑机宽度的一半)*2不同型号机械手计算：（机械手LM-注塑机一半）+（机械手LM-注塑机一半）HTF86/TJHTF120J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 36 40 45 螺杆长径比Screw L/D Ratio L/D 23.3 20 18.7 理论容量Shot Size(Theoretical) cm3173 214 270 注射重量Injection Weight(PS) g 157 195 246 注射压力Injection Pressure Mpa 197 160 126 螺杆转速Screw Speed rpm 0～195合模装置CLAMPING UNIT合模力Clamp Tonnage KN 1200移模行程Toggle Stroke mm 350拉杆内距Space Between Tie Bars mm 410x410最大模厚Max.Mold Height mm 430最小模厚Min.Mold Height mm 150顶出行程Ejector Stroke mm 120顶出力Ejector Tonnage KN 33顶出杆根数Ejector Number Piece 5 其它OTHERS最大油泵压力Max.Pump Pressure MPa 16油泵马达Pump Motor Power kw 11电热功率Heater Power kw 9.75HTF160J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 40 45 48 螺杆长径比Screw L/D Ratio L/D 22.5 20 18.8 理论容量Shot Size(Theoretical) cm3253 320 364 注射重量Injection Weight(PS) g 230 291 331 注射压力Injection Pressure Mpa 202 159 140 螺杆转速Screw Speed rpm 0～175合模装置CLAMPING UNIT合模力Clamp Tonnage KN 1600移模行程Toggle Stroke mm 420拉杆内距Space Between Tie Bars mm 455x455最大模厚Max.Mold Height mm 500最小模厚Min.Mold Height mm 180顶出行程Ejector Stroke mm 140顶出力Ejector Tonnage KN 33顶出杆根数Ejector Number Piece 5 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 15电热功率Heater Power kw 9.75HTF200J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 45 50 55 螺杆长径比Screw L/D Ratio L/D 22.2 20 18.2 理论容量Shot Size(Theoretical) cm3334 412 499 注射重量Injection Weight(PS) g 304 375 454 注射压力Injection Pressure Mpa 210 170 141 螺杆转速Screw Speed rpm 0～165合模装置CLAMPING UNIT合模力Clamp Tonnage KN 2000移模行程Toggle Stroke mm 470拉杆内距Space Between Tie Bars mm 510x510最大模厚Max.Mold Height mm 510最小模厚Min.Mold Height mm 200顶出行程Ejector Stroke mm 130顶出力Ejector Tonnage KN 62顶出杆根数Ejector Number Piece 9 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 18.5电热功率Heater Power kw 14.25这个图跟我看过的宝源机的顶棍孔差不多。
HTF250J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 50 55 60 螺杆长径比Screw L/D Ratio L/D 22 20 18.3 理论容量Shot Size(Theoretical) cm3442 535 636 注射重量Injection Weight(PS) g 402 487 579 注射压力Injection Pressure Mpa 205 169 142 螺杆转速Screw Speed rpm 0～180合模装置CLAMPING UNIT合模力Clamp Tonnage KN 2500移模行程Toggle Stroke mm 540拉杆内距Space Between Tie Bars mm 570x570最大模厚Max.Mold Height mm 570最小模厚Min.Mold Height mm 220顶出行程Ejector Stroke mm 130顶出力Ejector Tonnage KN 62顶出杆根数Ejector Number Piece 9 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 22电热功率Heater Power kw 16.65HTF300J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 60 65 70 螺杆长径比Screw L/D Ratio L/D 21.7 20 18.6 理论容量Shot Size(Theoretical) cm3727 853 989 注射重量Injection Weight(PS) g 662 776 900 注射压力Injection Pressure Mpa 213 182 157 螺杆转速Screw Speed rpm 0～185合模装置CLAMPING UNIT合模力Clamp Tonnage KN 3000移模行程Toggle Stroke mm 600拉杆内距Space Between Tie Bars mm 660x660最大模厚Max.Mold Height mm 660最小模厚Min.Mold Height mm 250顶出行程Ejector Stroke mm 160顶出力Ejector Tonnage KN 62顶出杆根数Ejector Number Piece 13 其它OTHERS最大油泵压力Max.Pump Pressure MPa 16油泵马达Pump Motor Power kw 30电热功率Heater Power kw 19.65HTF360J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 65 70 75 螺杆长径比Screw L/D Ratio L/D 21.5 20 18.7 理论容量Shot Size(Theoretical) cm31068 1239 1423 注射重量Injection Weight(PS) g 972 1127 1295 注射压力Injection Pressure Mpa 208 180 156 螺杆转速Screw Speed rpm 0～185合模装置CLAMPING UNIT合模力Clamp Tonnage KN 3600移模行程Toggle Stroke mm 660拉杆内距Space Between Tie Bars mm 710x710最大模厚Max.Mold Height mm 710最小模厚Min.Mold Height mm 250顶出行程Ejector Stroke mm 160顶出力Ejector Tonnage KN 110顶出杆根数Ejector Number Piece 13 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 37电热功率Heater Power kw 24.85HTF450J/TJ注射装置INJECTION UNIT A B C螺杆直径Screw Diameter mm 70 80 84 螺杆长径比Screw L/D Ratio L/D 22.9 20 19 理论容量Shot Size(Theoretical) cm31424 1860 2050 注射重量Injection Weight(PS) g 1296 1693 1866 注射压力Injection Pressure Mpa 204 156 141 螺杆转速Screw Speed rpm 0～155合模装置CLAMPING UNIT合模力Clamp Tonnage KN 4500移模行程Toggle Stroke mm 740拉杆内距Space Between Tie Bars mm 780x780最大模厚Max.Mold Height mm 780最小模厚Min.Mold Height mm 330顶出行程Ejector Stroke mm 200顶出力Ejector Tonnage KN 110顶出杆根数Ejector Number Piece 13其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 45电热功率Heater Power kw 29.45HTF530J/TJ注射装置INJECTION UNIT A B C D螺杆直径Screw Diameter mm 80 84 90 100 螺杆长径比Screw L/D Ratio L/D 22 21 19.6 17.6 理论容量Shot Size(Theoretical) cm32212 2438 2799 3456 注射重量Injection Weight(PS) g 2012 2218 2547 3145 注射压力Injection Pressure Mpa 180 163 142 115 螺杆转速Screw Speed rpm 0～130合模装置CLAMPING UNIT合模力Clamp Tonnage KN 5300移模行程Toggle Stroke mm 825拉杆内距Space Between Tie Bars mm 830x800最大模厚Max.Mold Height mm 850最小模厚Min.Mold Height mm 350顶出行程Ejector Stroke mm 200顶出力Ejector Tonnage KN 158顶出杆根数Ejector Number Piece 17 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 55电热功率Heater Power kw 40.25HTF650J/TJ注射装置INJECTION UNIT A B C D螺杆直径Screw Diameter mm 80 90 100 110 螺杆长径比Screw L/D Ratio L/D 24.8 22 19.8 18 理论容量Shot Size(Theoretical) cm32036 2576 3181 3849 注射重量Injection Weight(PS) g 1853 2344 2895 3503 注射压力Injection Pressure Mpa 224 177 143 118 螺杆转速Screw Speed rpm 0～120合模装置CLAMPING UNIT合模力Clamp Tonnage KN 6500移模行程Toggle Stroke mm 900拉杆内距Space Between Tie Bars mm 895x895最大模厚Max.Mold Height mm 900最小模厚Min.Mold Height mm 400顶出行程Ejector Stroke mm 260顶出力Ejector Tonnage KN 175顶出杆根数Ejector Number Piece 17 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 22+37电热功率Heater Power kw 49.25HTF780J/TJ注射装置INJECTION UNIT A B C D螺杆直径Screw Diameter mm 90 100 110 120 螺杆长径比Screw L/D Ratio L/D 24.4 22 20 18.3 理论容量Shot Size(Theoretical) cm32799 3456 4181 4976 注射重量Injection Weight(PS) g 2547 3145 3805 4528 注射压力Injection Pressure Mpa 228 184 152 128 螺杆转速Screw Speed rpm 0～104合模装置CLAMPING UNIT合模力Clamp Tonnage KN 7800移模行程Toggle Stroke mm 980拉杆内距Space Between Tie Bars mm 980x980最大模厚Max.Mold Height mm 980最小模厚Min.Mold Height mm 400顶出行程Ejector Stroke mm 260顶出力Ejector Tonnage KN 186顶出杆根数Ejector Number Piece 21 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 37+37电热功率Heater Power kw 61.15HTF900J/TJ注射装置INJECTION UNIT A B C D螺杆直径Screw Diameter mm 90 100 110 120 螺杆长径比Screw L/D Ratio L/D 24.4 22 20 18.3 理论容量Shot Size(Theoretical) cm32799 3456 4181 4976 注射重量Injection Weight(PS) g 2547 3145 3805 4528 注射压力Injection Pressure Mpa 228 184 152 128 螺杆转速Screw Speed rpm 0～114合模装置CLAMPING UNIT合模力Clamp Tonnage KN 9000移模行程Toggle Stroke mm 1020拉杆内距Space Between Tie Bars mm 1060x1000最大模厚Max.Mold Height mm 1020最小模厚Min.Mold Height mm 450顶出行程Ejector Stroke mm 260顶出力Ejector Tonnage KN 186顶出杆根数Ejector Number Piece 21 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 37+45电热功率Heater Power kw 61.15HTF1000J/TJ注射装置INJECTION UNIT A B C D螺杆直径Screw Diameter mm 100 110 120 130 螺杆长径比Screw L/D Ratio L/D 24.4 22 20.2 18.6 理论容量Shot Size(Theoretical) cm33770 4562 5429 6371 注射重量Injection Weight(PS) g 3431 4145 4940 5798 注射压力Injection Pressure Mpa 211 174 146 125 螺杆转速Screw Speed rpm 0～101合模装置CLAMPING UNIT合模力Clamp Tonnage KN 10000移模行程Toggle Stroke mm 1100拉杆内距Space Between Tie Bars mm 1090x1090最大模厚Max.Mold Height mm 1100最小模厚Min.Mold Height mm 500顶出行程Ejector Stroke mm 320顶出力Ejector Tonnage KN 215顶出杆根数Ejector Number Piece 21 其它OTHERS最大油泵压力Max.Pump Pressure MPa 17.5油泵马达Pump Motor Power kw 37+55电热功率Heater Power kw 68.75。
