下载文档原格式
C系列彩屏智能终端使用说明书（V1.0.1）------------------------------------------------------------------------------------------ 感谢您关注和使用金鹏彩屏系列液晶显示器产品，欢迎您提出意见和建议，我们将竭诚为您服务、让您满意。
您可以浏览h p://w ww.g pt lc m.c n了解最新的产品与应用信息，或拨打热线电话0758－2317156及向*************邮箱发E-mail获取具体的技术咨询与服务。
金鹏实业有限公司Golden Palm Industry Co., Ltd.修订历史版本日期原因V1.0 2011年6月13日创建文档,V1.0.1 2011年7月18日增加电流参数一、产品简介 (4)二、产品选型表 (5)三、极限参数 (5)四、引脚说明 (5)五、指令集表 (6)5.1 指令格式 (6)5.2颜色格式 (7)5.3指令列表 (7)5.4 指令使用详解 (12)5.4.1 握手命令 (12)5.4.2设置前/背景色 (12)5.4.3清屏 (12)5.4.4设置文字行间距和列间距 (12)5.4.5设置过滤颜色 (12)5.4.6文本显示 (13)5.4.7光标显示 (13)5.4.8图片显示 (14)5.4.9图片剪切 (14)5.4.10动画显示 (14)5.4.11画点 (15)5.4.12画线 (15)5.4.13画空心圆 (15)5.4.14画实心圆 (16)5.4.15画空心矩形 (16)5.4.16画实心矩形 (16)5.4.17画空心椭圆 (17)5.4.18画实心椭圆 (17)5.4.19背光调节 (17)5.4.20触摸值上传 (17)5.4.21 读取触摸值 (17)5.4.22触摸屏校准 (18)5.4.23设置波特率 (18)5.4.24 蜂鸣器控制 (18)六、板上短路点的使用 (19)七、模块外型尺寸图 (19)一、产品简介肇庆金鹏电子集团有限公司的彩屏智能型彩屏终端，是在汲取了众多客户要求和建议的基础上，采用32位ARM处理器+ FPGA双核控制架构开发的一款高性能、低功耗、易使用的64K色的TFT真彩显示器，可以直接和具有UART串行接口的MCU（如51单片机、AVR、PIC、DSP、ARM、工控机等）连接。
UC-5100 Series Hardware User’s ManualEdition 1.1, October 2018/product© 2018 Moxa Inc. All rights reserved.UC-5100 Series Hardware User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance withthe terms of that agreement.Copyright Notice© 2018 Moxa Inc. All rights reserved.TrademarksThe MOXA logo is a registered trademark of Moxa Inc.All other trademarks or registered marks in this manual belong to their respective manufacturers.DisclaimerInformation in this document is subject to change without notice and does not represent a commitment on the part of Moxa.Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time.Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use.This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication.Technical Support Contact Information/supportMoxa AmericasToll-free: 1-888-669-2872 Tel: +1-714-528-6777 Fax: +1-714-528-6778Moxa China (Shanghai office) Toll-free: 800-820-5036Tel: +86-21-5258-9955 Fax: +86-21-5258-5505Moxa EuropeTel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99Moxa Asia-PacificTel: +886-2-8919-1230 Fax: +886-2-8919-1231Moxa IndiaTel: +91-80-4172-9088 Fax: +91-80-4132-1045Table of Contents1.Introduction ...................................................................................................................................... 1-1Overview ........................................................................................................................................... 1-2 Model Descriptions .............................................................................................................................. 1-2 Package Checklist ............................................................................................................................... 1-2 Product Features ................................................................................................................................ 1-3 Hardware Block Diagram ..................................................................................................................... 1-3 2.Hardware Introduction...................................................................................................................... 2-1Appearance ........................................................................................................................................ 2-2 LED Indicators .................................................................................................................................... 2-5 Reset Button ...................................................................................................................................... 2-5 Reset to Default Button ....................................................................................................................... 2-5 Real Time Clock .................................................................................................................................. 2-5 Installation Options ............................................................................................................................. 2-6 DIN-Rail Mounting ....................................................................................................................... 2-6Optional DIN-Rail Mounting .......................................................................................................... 2-6 3.Hardware Connection Description ..................................................................................................... 3-1Wiring Requirements ........................................................................................................................... 3-2 Connecting the Power .................................................................................................................. 3-2Grounding the Unit ...................................................................................................................... 3-2 Connecting to the Console Port ............................................................................................................. 3-3 Connecting to the Network ................................................................................................................... 3-3 Connecting to a Serial Device ............................................................................................................... 3-4 Connecting to a DI/DO Device .............................................................................................................. 3-4 Connecting to a CAN Device ................................................................................................................. 3-4 Connecting to a USB Device ................................................................................................................. 3-5 Connecting the Cellular/Wi-Fi Module and Antenna ................................................................................. 3-5 Installing Micro SIM Cards ................................................................................................................... 3-7 Installing the SD Card ......................................................................................................................... 3-8 Adjusting the CAN DIP Switch .............................................................................................................. 3-8 Adjusting Serial Port DIP Switch ........................................................................................................... 3-8 A.Regulatory Approval Statements ....................................................................................................... A-11Introduction The UC-5100 Series embedded computers are designed for industrial automation applications. The computers feature 4 RS-232/422/485 full-signal serial ports with adjustable pull-up and pull-down resistors, dual CAN ports, dual LANs, 4 digital input channels, 4 digital output channels, a SD socket, and a mini PCIe socket for wireless module in a compact housing with convenient front-end access to all these communication interfaces. The following topics are covered in this chapter:❒Overview❒Model Descriptions❒Package Checklist❒Product Features❒Hardware Block DiagramOverviewThe UC-5100 Series embedded computers are designed for industrial automation applications. The computers feature 4 RS-232/422/485 full-signal serial ports with adjustable pull-up and pull-down resistors, dual CANports, dual LANs, 4 digital input channels, 4 digital output channels, a SD socket, and a mini PCIe socket for wireless module in a compact housing with convenient front-end access to all these communication interfaces. Model DescriptionsThe UC-5100 Series includes the following models:•UC-5101-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, 4 DI, 4 DO, -10 to 60°C operating temperature range•UC-5102-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, mini PCIe socket, 4 DI, 4 DO, -10 to 60°C operating temperature range•UC-5111-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, 2 CAN ports,4 DI, 4 DO,-10 to 60°C operating temperature range•UC-5112-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, mini PCIe socket, 2 CAN ports, 4 DI, 4 DO, -10 to 60°C operating temperature range•UC-5101-T-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, 4 DI, 4 DO, -40 to 85°C operating temperature range•UC-5102-T-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, mini PCIe socket, 4 DI, 4 DO, -40 to 85°C operating temperature range•UC-5111-T-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, 2 CAN ports,4 DI, 4 DO, -40 to 85°C operating temperature range•UC-5112-T-LX: Industrial computing platform with 4 serial ports, 2 Ethernet ports, SD socket, 2 CAN ports, mini PCIe socket, 4 DI, 4 DO, -40 to 85°C operating temperature rangeNOTE The operating temperature range of the wide temperature models is:-40 to 70°C with an LTE accessory installed-10 to 70°C with a Wi-Fi accessory installed.Package ChecklistBefore installing a UC-5100 computer, verify that the package contains the following items:•UC-5100 Series computer•Console cable•Power jack•Quick Installation Guide (printed)•Warranty cardNotify your sales representative if any of the above items are missing or damaged.NOTE The console cable and power jack can be found beneath the molded pulp cushioning inside the product box.Product Features•ARMv7 Cortex-A8 1000 MHz processor•Dual auto-sensing 10/100 Mbps Ethernet ports• 4 software-selectable RS-232/422/485 ports supporting all signals•Dual Industrial CAN 2.0 A/B protocol supported•Moxa Industrial Linux with 10-year superior long term support•Mini PCIe socket for Wi-Fi/Cellular module•Micro SD socket for storage expansion•Supports TPM v2.0 (optional)•-40 to 85°wide temperature range and -40 to 70°C with LTE enabledFor a complete set of specifications, refer to the product datasheet available on the Moxa Website. Hardware Block Diagram2Hardware Introduction The UC-5100 embedded computers are compact and rugged, making them suitable for industrial applications. The LED indicators allow you to monitor performance and identify trouble spots quickly, and the multiple ports can be used to connect a variety of devices. The UC-5100 Series comes with a reliable and stable hardware platform that lets you devote the bulk of your time to application development. In this chapter, we provide basic information about the embedded computer’s hardware and its various components.The following topics are covered in this chapter:❒Appearance❒LED Indicators❒Reset Button❒Reset to Default Button❒Real Time Clock❒Installation OptionsD IN-Rail MountingO ptional DIN-Rail MountingAppearance Front ViewUC-5101UC-5102UC-5111UC-5112Dimensions [units: mm (in)] UC-5101UC-5102UC-5111UC-2112LED IndicatorsThe function of each LED is described in the table below: LED Name Status FunctionPower Green Power is on, and the device is functioning normally OffPower is offReadyYellow OS has been successfully enabled and the device is ready EthernetGreen Steady On: 10 Mbps Ethernet linkBlinking: Data transmission is in progress Yellow Steady On: 100 Mbps Ethernet linkBlinking: Data transmission is in progressOff Transmission speed below 10 Mbps or the cable is not connectedSerial (Tx) Green Serial port is transmitting data Off Serial port is not transmitting data Serial (Rx)Yellow Serial port is receiving data Off Serial port is not receiving dataL1/L2/L3(UC-5102/5112) YellowThe number of glowing LEDs indicates the signal strength. All LEDs: Excellent L1 & L2 LEDS : Good L1 LED : PoorOffNo wireless module detectedL1/L2/L3(UC-5101/5111)Yellow/OffProgrammable LEDs defined by usersReset ButtonThe UC-5100 computer is provided with a Reset button, which is located on the front panel of the computer. To reboot the computer, press the reset button for 1 second.Reset to Default ButtonThe UC-5100 is also provided with a Reset to Default button which can be used to reset the operating system back to the factory default status. Press and hold the Reset to Default button between 7 to 9 seconds to reset the computer to the factory default settings. When the reset button is held down, the Ready LED will blink once every second. The Ready LED will become steady when you hold the button continuously for 7 to 9 seconds. Release the button within this period to load the factory default settings.Real Time ClockThe UC-5100’s real time clock is powered by a non-chargeable battery. We strongly recommend that you do not replace the lithium battery without help from a qualified Moxa support engineer. If you need to change the battery, contact the Moxa RMA service team.Installation OptionsDIN-Rail MountingThe aluminum DIN-rail attachment plate is already attached to the product’s casing. To mount the UC-5100 on to a DIN rail, make sure that the stiff metal spring is facing upwards and follow these steps. Step 1Insert the top of the DIN rail into the slot just below the stiff metal spring in the upper hook of the DIN-rail mounting kit.Step 2Push the UC-5100 towards the DIN rail until theDIN-rail attachment bracket snaps into place.Optional DIN-Rail MountingThe UC-5100 can be mounted with the optional DIN rail mounting kit. Follow these steps for the installation. 1. Attach the optional DIN-rail mounting kit on therear panel with two screws.2. Pull down the slider of the DIN-rail bracketlocated at the back of the unit.3. Insert the top of the DIN rail into the slot justbelow the upper hook of the DIN-rail bracket. 4. Latch the unit firmly on to the DIN rail as shownin the illustrations below.5. Once the computer is mounted properly, youwill hear a click and the slider will rebound back into place automatically.Note this optional DIN-rail mounting kit should be purchased separately.3 Hardware Connection DescriptionIn this chapter, we describe how to connect the UC-5100 to a network and various devices for first time testing purposes.The following topics are covered in this chapter:❒Wiring RequirementsC onnecting the PowerG rounding the Unit❒Connecting to the Console Port❒Connecting to the Network❒Connecting to a Serial Device❒Connecting to a DI/DO Device❒Connecting to a CAN Device❒Connecting to a USB Device❒Connecting the Cellular/Wi-Fi Module and Antenna❒Installing Micro SIM Cards❒Installing the SD Card❒Adjusting the CAN DIP Switch❒Adjusting Serial Port DIP SwitchWiring RequirementsIn this section, we describe how to connect various devices to the embedded computer. Be sure to read and follow these common safety precautions before proceeding with the installation of any electronic device: • Use separate paths to route wiring for power and devices. If power wiring and device wiring paths mustcross, make sure the wires are perpendicular at the intersection point.NOTEDo not run signal or communication wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.• You can use the type of signal transmitted through a wire to determine which wires should be kept separate.The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together. • Keep input wiring and output wiring separate.• When necessary, it is strongly advised that you label wiring to all devices in the system.Connecting the PowerTerminal BlockConnect the 9 to 48 VDC power line to the terminal block, which is connector to the UC-5100 Series computer. If the power is supplied properly, the “Power” LED will glow asolid green light. The power input location and pin definition are shown in the adjacent diagram.SG: The Shielded Ground (sometimes called Protected Ground) contact is at the bottomcontact of the 3-pin power terminal block connector when viewed from the angle shown here. Connect the wire to an appropriate grounded metal surface or through the groundingscrew on top of the device.Grounding the UnitGrounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.Connecting to the Console PortThe UC-5100’s console port is a 4-pin pin-header RS-232 port located on the top panel of the case. It is designed for serial console terminals, which are useful for identifying the boot up message, or for debugging when the system cannot boot up.PIN Signal1 -2 - 3GND 4 TxD 5 RxD 6 - 7 - 8-Connecting to the NetworkThe Ethernet ports are located on the front panel of the UC-5100 computers. The pin assignments for the Ethernet port are shown in the following figure. If you are using your own cable, make sure that the pin assignments on the Ethernet cable connector match the pin assignments on the Ethernet port.PinSignal 1 Tx+ 2 Tx- 3 Rx+ 4 – 5– 6 Rx- 7 – 8–Connecting to a Serial DeviceThe serial ports are located on the front panel of the UC-5100 computer. Use a serial cable to connect your serial device to the computer’s serial port. These serial ports have RJ45 connectors and can be configured for RS-232, RS-422, or RS-485 communication. The pin location and assignments are shown in the table below.Pin RS-232RS-422 RS-485 1 DSR - - 2 RTS TxD+ - 3 GND GND GND 4 TxD TxD- - 5RxD RxD+ Data+ 6 DCD RxD-Data- 7 CTS - - 8DTR--Connecting to a DI/DO DeviceThe UC-5100 Series comes with 4 digital inputs and 4 digital outputs. The DI/DO connectors are located on the top panel of the computer. Refer to the diagram on the left for the pin definitions. For the wiring method, refer to the following figure:Connecting to a CAN DeviceThe UC-5111/5112 comes with 2 CAN ports, allowing users to connect CAN device. The pin location and assignments are shown in the following table:PIN Signal 1 CAN_H 2 CAN_L 3 CAN_GND4- 5 - 6 - 7 CAN_GND8-Connecting to a USB DeviceThe UC-5100 Series computers come with a USB port located at the lower part of the front panel, allowing users to connect to a device with an USB interface. The USB port uses a type A connector. Connecting the Cellular/Wi-Fi Module and AntennaThe UC-5102 and UC-5112 computerscome with one Mini PCIe socket forinstalling one cellular or Wi-Fi module.Unfasten the two screws on the rightpanel to remove the cover and find thelocation of the socket.The cellular module package includes 1 cellular module, and 2 screws. The cellular antennas should bepurchased separately to fit your installation requirements.Follow these steps to install the cellular module.1.Set the antenna cables aside for convenience of installation andclear the wireless module socket as shown in the figure.2.Insert the cellular module into the socket and fasten two screws(included in the package) on to the top of the module.We recommended using a tweezer when installing or removingthe module.3.Connect the free ends of the two antenna cables next to thescrews as shown in the image.4.Replace the cover and secure it using two screws.5.Connect the cellular antennas to the connectors.Antenna connectors are located on the front panel of thecomputer.The Wi-Fi module package includes 1 Wi-Fi module, and 2 screws. The antenna adapters and Wi-Fi antennas should be purchased separately to fit your installation requirements.Follow these steps to install a Wi-Fi module.1. Set the antenna cables aside and clear the wireless module socket as shown in the figure for convenience of installation.2. Insert the Wi-Fi module into the socket and fasten two screws (included in the package) on to the top of the module.We recommended using a tweezer when installing or removing the module.3. Connect the free ends of the two antenna cables next to the screws as shown in the image.4. Replace the cover and secure it with two screws.5. Connect the antenna adapters to the connectors on the front panel of the computer.6. Connect the Wi-Fi antennas to the antenna adapters.Installing Micro SIM CardsYou will need to install a Micro SIM card on your UC-5100 computer. Follow these steps to install the Micro SIM card.1. Remove the screw on the cover located on the frontpanel of the UC-5100.2. Insert the Micro SIM card into the socket. Make sureyou place the card in the right direction. To remove the Micro SIM card, simply push the Micro SIM card and release it. Note: There are two Micro SIM card sockets allowing users to install two Micro SIM cards simultaneously. However, only oneMicro SIM card can be enabled for use.UC-5100 Series Hardware Hardware Connection Description 3-8Installing the SD CardThe UC-5100 Series computers come with a socket for storage expansion that allows users to install an SD card. Follow these steps to install the SD card:1. Unfasten the screw and remove the panel cover.The SD socket is located on the front panel of thecomputer.2. Insert the SD card into the socket. Ensure that thecard is inserted in the right direction.3. Replace the cover and fasten the screw on thecover to secure the cover.To remove the SD card, simply push the card in andrelease it.Adjusting the CAN DIP SwitchThe UC-5111 and UC-5112 computers come with one CAN DIP switch for users to adjust the CAN termination resistor parameters. To set up the DIP switch, do the following:1. Find the DIP switch location on the top panel of thecomputer2. Adjust the setting as required. The ON value is 120Ω, and the default value is OFF.Adjusting Serial Port DIP SwitchThe UC-5100 computers come with a DIP switch for users to adjust the pull-up/pull-down resistors for the serial port parameters. The serial port DIP switch is located on the bottom panel of the computer.Adjust the setting as required. The ON setting corresponds to 1KΩ and the OFF setting corresponds to 150KΩ. The default setting is OFF.Each port consists of 4 pins; you must switch all 4 pins of a port simultaneously to adjust the value of the port.A Regulatory Approval StatementsThis device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesiredoperation.Class A: FCC Warning! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the users will be required to correct the interference at their own expense.European Community。
南京手机网 行诺 基 亚诺 基 亚三 星摩托罗拉C51550E66灰黑白2G1610C3730黑灰880A810黑白600X3红兰2G1060E71灰白2G1910C5130#730A1210白粉棕1200X6红黑16G#2610E72I黑2540C5510灰#910A1600黑双原1570X616G导航2600N72黑粉1281090C6112双卡双待1370A1600黄金版2300X6红32G#2700N73黑5121470D988黑金双原2210A1890黑21801202黑180N78棕4G1900E1080黑160E11灰14301208红黑205N79黑4G2070E1100黑200E60026501209兰灰215N85桐8G2180E1150红240VE6611401661黑230N85黑桐2G2130E1310黑360V82G兰金12401616220N86黑白8G#3000E2120黑300V9#16501680黑300N96灰16G2400G508金双原1810ME501黑26501682黑230N96黑16G2810F278i黑白780MT710黑29001800250N97I银32G#3530F488红双原1480XT800黑41802220红黑兰400N97导航3680I688银双原$1810W2161802320黑300N97迷你版8G#3170I6330黑双原$2300W230黑2002330红黑380 三 星I80008G双原#3250W3882402332棕350L168银黑兰660I89108G双原#3650WX3903002600金兰420L708银粉630 飞 利 浦R189002630黑白330L878银1440X100400 三星C网2680灰兰4440J708金银红600X320780E1892202680紫490J808黑粉紫720X500黑银990B1892202690黑白560M628黑白银520X501黑1060S2596602700红黑1G620M2710兰780X530黑粉红1120S3597602720黑480M3318红940X550黑990i32926002730黑红#700S3310670X600黑灰1080i89928003208黑1G手写920S33701140X603黑1490M5199203208白1G手写940S3501兰粉810X605黑1520M60914505000紫兰绿黑460S3550黑850X606黑1690F2995505030灰红280S3601银粉730X630黑1060F3096605130蓝红1G710S3650黄橙白粉1080X710黑双卡1400F33913605132银1G680S3830黑红#930X800黑棕1300F53914305230大导航1450S3930黑红兰$1020X806黑1880F619G+C15005232彩白2G1210S51501570X810黑1570F639+10505233黑银1230S5200兰金红1140X830黑金1600F68911005310红兰2G910S5230白粉黑1170C600黑G+C1490F80926505320红兰2G1070S55501580C700黑G+C1590F83921505320i红兰2G1160S5628银#1590W186黑1370W23912905330黑2G#1390S5630C黑$1230K700黑白银1520W589G+C42505530黑白4G1570S6700银紫1250夏普6010C1400W629G+C27505800W2030S7350黑粉银双1690夏普6110C1200W699棕G+C44805802兰黑8G1730S7070白1540夏普6118C1100W709G+C45506120I黑白#1040S71201650夏普6220C2500W799G+C7450。
页数：第1 页，共5 页描述221001A01是为产品XL4003制作的演示板，用于DC8V~32V输入，输出电压5V，输出电流3.4A的降压恒压应用演示，最高转换效率可以达到93%。
XL4003是开关降压型DC-DC转换芯片；固定开关频率300KHz，可减小外部元器件尺寸，方便EMC设计。
芯片具有出色的线性调整率与负载调整率，输出电压支持0.8V~30V间任意调节。
芯片内部集成过流保护、过温保护、短路保护等可靠性模块。
XL4003为标准TO252-5L封装，集成度高，外围器件少，应用灵活。
DEMO原理图VOUT=0.8*(1+R2/R1)引脚介绍页数：第2 页，共5 页物料清单性能测试转换效率页 数：第 3 页， 共 5 页转换效率： 线性调整率与负载调整率：Efficiency VS Load currentE f f i c i e n c y (%)Load current(A)Output voltage VS Output currentO u t p u t v o l t a g e (V )Output current(A)页数：第4 页，共5 页DEMO实物图PCB布局40mm顶层底层页数：第5 页，共5 页应用信息输入电容选择在连续模式中，转换器的输入电流是一组占空比约为VOUT/VIN的方波。
为了防止大的瞬态电压，必须采用针对最大RMS电流要求而选择低ESR(等效串联电阻)输入电容器。
对于大多数的应用，1个10uF的输入电容器就足够了, 它的放置位置尽可能靠近XL4003的位置上。
最大RMS电容器电流由下式给出：IRMS≈IMAX*√VOUT(VIN-VOUT)VIN其中，最大平均输出电流IMAX等于峰值电流与1/2峰值纹波电流之差，即IMAX=ILIM-△IL/2。
在未使用陶瓷电容器时，还建议在输入电容上增加一个0.1uF至1uF的陶瓷电容器以进行高频去耦。
输出电容选择在输出端应选择低ESR电容以减小输出纹波电压，一般来说，一旦电容ESR得到满足，电容就足以满足需求。
广州大彩光电科技有限公司版权所有版本记录销售与服务广州大彩光电科技有限公司电话：************-601传真：************Email：*************（咨询和支持服务）网站：地址：广州黄埔区（科学城）玉树华新园C栋3楼网络零售官方旗舰店：https://目录1. 硬件介绍 (1)1.1产品外观 (1)1.2硬件配置 (1)1.3调试工具 (2)2. 产品规格 (3)3. 产品尺寸 (5)4. 引脚定义 (6)5. 可靠性测试 (7)5.1ESD测试 (7)5.1.1执行标准 (7)5.1.2测试环境 (7)5.1.3测试数据 (8)5.2高低温老化测试 (8)5.2.1测试环境 (8)5.2.2测试数据 (9)5.3群脉冲测试 (9)5.3.1执行标准 (9)5.3.2测试环境 (9)5.3.3测试数据 (9)5.4辐射测试 (10)5.4.1执行标准 (10)5.4.2测试环境 (10)5.4.3测试数据 (10)6. 型号定义 (12)7. RS232与TTL电平转换 (13)8. 协议配置 (14)9. LUA脚本配置 (15)10. 包装与物理尺寸 (16)11. 产品架构 (17)12. 开发软件 (18)12.1什么是虚拟串口屏 (18)12.2Keil与虚拟串口屏绑定调试 (19)13. 开发文档 (20)14. 免责声明 (21)1. 硬件介绍本章节主要介绍产品的一些外观参考图、硬件配置图和调试所需工具。
1.1 产品外观以下为该尺寸不同型号的外观参考图，如图1-1、图1-2所示。
注：未涉及关键结构工艺修改或布局大调整，仅产品工艺或可靠性方面的变更迭代，公司不予对外发起变更，具体以收到的实物为准。
图1-1 3.5寸电阻触摸参考图图1-2 3.5寸无触摸参考图1.2 硬件配置以下为该尺寸产品硬件配置参考图，以电阻屏举例说明，如图1-3所示。
图1-3硬件配置图销售咨询：************-601Email:*************1.3 调试工具以下为该产品调试工具参考图，以电阻屏举例说明，如图1-4所示。
浪潮英信服务器SA5212M5用户手册文档版本V2.4发布日期2022-06-28版权所有© 2017-2022浪潮电子信息产业股份有限公司。
保留一切权利。
未经本公司事先书面许可，任何单位和个人不得以任何形式复制、传播本手册的部分或全部内容。
环境保护请将我方产品的包装物交废品收购站回收利用，以利于污染预防，共同营造绿色家园。
商标说明Inspur浪潮、Inspur、浪潮、英信是浪潮集团有限公司的注册商标。
本手册中提及的其他所有商标或注册商标，由各自的所有人拥有。
安全声明服务器产品安全一直是浪潮关注的焦点，保障产品安全是浪潮的关键战略之一。
为使您更清晰地了解服务器产品，请注意如下安全风险声明。
●在调整用途或淘汰服务器时，为了保护数据隐私，建议从BIOS、BMC中恢复固件出厂设置、删除信息、清除日志。
同时，建议采用第三方安全擦除工具对硬盘数据进行全面安全擦除。
●您购买的产品、服务或特性在业务运营或故障定位的过程中将可能获取或使用用户的某些个人数据（如告警邮件接收地址、IP地址），故您有义务根据所适用国家的法律制定必要的用户隐私政策并采取足够的措施，以确保用户的个人数据受到充分的保护。
●服务器开源软件声明的获取，请直接联系浪潮客户服务人员咨询。
●部分用于生产、装备、返厂检测维修的接口、命令，定位故障的高级命令，如使用不当，将可能导致设备异常或者业务中断，故不在本资料中说明。
如需要，请向浪潮申请。
●浪潮建立了产品安全漏洞应急和处理机制，保证第一时间及时处理产品安全问题。
若您在浪潮产品中发现任何安全问题，或者寻求有关产品安全漏洞的必要支持，可以直接联系浪潮客户服务人员。
浪潮将一如既往的严密关注产品与解决方案的安全性，为客户提供更满意的服务。
内容声明您购买的产品、服务或特性等应受浪潮集团商业合同和条款的约束。
本文档中描述的全部或部分产品、服务或特性可能不在您的购买或使用范围之内。
除非合同另有约定，浪潮集团对本文档的所有内容不做任何明示或默示的声明或保证。
可编辑修改精选全文完整版目录一、股权奖励案例3〔一〕航天科工：下属四级公司员工持股31.航天科工简介32.实施方案33.特点分析4〔二〕海康威视：战略投资者股权转让51.海康威视简介52.实施方案53.特点分析5〔三〕江中集团：企业改制与管理层持股61.江中集团简介62.实施方案63.特点分析7〔四〕华康药业：上市公司的子公司股票期权鼓励71.华康药业简介72.实施方案83.特点分析8〔五〕欧亚集团：鼓励基金+个人购股91.欧亚集团简介92实施方案93.特点分析10〔六〕长虹：奖励基金+管理层持股101.长虹简介102.实施方案10〔七〕TCL—增量奖股鼓励121. TCL简介122.实施方案123.特点分析13二、现金奖励案例14(一)航天恒星：岗位分红权141.航天恒星简介142.实施方案143特点分析15(二)某国有控股企业—工程收益分红〔2010年〕151.实施方案15(三)某国有独资公司—工程收益分红〔2012年〕181.实施方案18(四)南方航空—股票增值权鼓励方案201.南方航空简介202.实施方案20一、股权奖励案例在该局部中，选取的案例企业以国资为主，包括航天科工、海康威视等央企以及江中集团、华康药业等地方国资企业，每个案例代表一种或者多种鼓励方式，包括员工持股、战略投资者转让、股票期权等。
选取的案例企业包括海康威视、欧亚集团等上市企业，也包括航天科工等非上市企业。
〔一〕航天科工：下属四级公司员工持股1.航天科工简介国航天科工集团公司〔简称航天科工〕是中央直接收理的国有特大型高科技企业，前身为1956年10月成立的国防部第五研究院，先后经历了第七机械工业部〔1981年9月第八机械工业部并入〕、航天工业部、航空航天工业部、中国航天工业总公司的历史沿革。
1999年7月成立中国航天机电集团公司，2001年7月更名为中国航天科工集团公司。
航天科工现由总部、5个研究院、2个科研生产基地、11个公司制、股份制企业构成。
超市销售岗位的实习周记5篇超市销售岗位的实习周记篇1一、实习目的让学生将所学的专业知识应用于社会实践中，进一步提高专业技能，使学生深化对所学知识的认识，将所学的理论知识运用于实践工作中，增强学生的组织管理能力、独立分析问题和解决问题的能力、实际动手操作能力市场预测与分析能力等综合能力。
通过毕业实习接触认识社会，提高社会交往能力，学习优秀员工的优秀品质和敬业精神，培养素质，早点进入社会工作，从校园到社会的过渡，适应社会，为以后的工作打下基础。
二、实习时间_月_日—_月_日三、实习地点__市__电器有限公司__专柜四、实习内容主要在店内销售__，有时会根据活动计划被派出去做外场宣传，学习了解公司性质、销售技巧、团队协作精神、礼仪等各方面的知识。
掌握产品相关知识，凭着对长虹空调的了解和与其它公司产品的对比，突出本公司长虹空调的优点和公司的良好信誉，向顾客推销产品，并尽量推销系列产品，巧用销售技巧，出色地完成公司分配的任务。
在实习期间，我接触了一些办公用品，如传真机、碎纸机、打印复印机、扫描仪等，掌握了这些机器的基本操作。
五、实习体会刚开始工作时，最要是熟悉产品和做一些打杂的工作，对于我来说刚进入陌生的环境难免会有些不适应，而且还要每天站着，不能坐着，刚开始上班的几天全身都痛，感觉非常的恼火，甚至有点后悔选着销售的工作，也不知道自己能不能坚持下来。
庆幸的是我的同事们大都数都比较好，是同事们友善的微笑缓解我的脚痛，偶尔她们也会跟你讲讲她们当初参加工作的一些经验和心得体会，最开始做店内销售但是要适应站好几个小时，也可以看资料来熟悉产品转移注意力，能够得到她们的指导也是很高兴的，不够在销售技巧上你就别指望别人能教你多少了，都是需要自己细心的去摸索、领悟成为自己的销售技巧的，有的时候感觉就像是在一个大家庭，相处愉快合作愉快。
但是有时看见他们抢单而恶语相向时，心里凉凉的。
只要不促及到自己的利益，平时相处时都是很礼貌的，不管大事小事都要说声谢谢。
Ricoh RX Series 系列互动电子液晶显示器用户手册Ver1.0RX-E**C1系列版本历史版本更新日期备注1.0 2022/4/1目录1. 产品外观 (4)2. 接口 (5)3. 快速入门指南 (6)3.1桌面介绍 (6)3.2工具栏介绍 (7)3.3白板介绍 (8)3.4批注介绍 (11)3.5投屏介绍 (11)1.产品外观序号内容1 扬声器2 书写笔磁吸区域3 开关机键：灯圈颜色：红灯：通电未开机蓝灯：使用中红蓝交替：休眠中或运行中无法操作4 前置USB口区域5 电源线插口及电源键区域注：接通电源后务必打开电源键，否则无法开机6 无线模块安装处7 接口矩阵区域2.接口序号种类功能描述1 HDMI IN HDMI信号输入接口2 USB2.0 连接USB设备3 LAN 网络接口4 TOUCH 触摸信号输出接口5 RS232 也称作COM口，主流计算机通用串行接口，连接带有RS232接口的设备6 AUDIO OUT 连接到带有音频输入功能的设备7 AUDIO IN 连接到带有音频输出功能的设备8 VGA VGA信号输入接口3.快速入门指南3.1桌面介绍序号内容功能描述1 时间日期区域可在此区域查看时间日期，可以通过设置选择12小时制或24小时制。
2 传屏码区域电脑端可以通过传屏码进行投屏。
点击传屏码，会出现二维码，手机可以扫描二维码实现投屏3 网络/存储状态区域可在此区域看到有线网络、无线网络、无线热点、U盘的实时状态。
有线网络未连接无线网络已连接无线热点已开启U盘已插入点击对应网络符号可以对该网络进行设置4 桌面按钮我们已将最常用的软件预置到了桌面上，不可更改5 更多软件按钮点击可查看机器上安装的其他软件3.2工具栏介绍点击屏幕左右的小三角，即可调出侧边工具栏：项目功能描述收回/打开菜单箭头朝向边框收回菜单，箭头朝向屏幕打开菜单返回键点击返回上一级菜单HOME键点击回到桌面多任务键点击可查看目前正在运行中的程序，可以一键清除所有运行中的程序小工具小工具包含计时器、日历、相机、投票器、触摸锁、截屏、录屏、护眼、锁屏等可以快捷进入设置、文件快传和无线传屏信道切换点击可以查看当前有哪些信道激活中，点击信道名称，切换至该信道。
15inch HDMI LCD (B)User Manual 5 inch Resistive Touch Screen LCD, HDMI interface, supports various systemsFeatures●800×480 high resolution, touch control ●Supports Raspberry Pi, and driver is provided (works with custom Raspbian directly) ●Supports BB Black, comes with related images like : Angstrom, Android4.2.2 ●Supports Banana Pi / Banana Pro, comes with related images like : Lubuntu, Raspbian ● Not only for mini-PCs, it can work as a computer monitor just like any other general HDMI screen(touch function is unavailable in this case)●HDMI interface for displaying, USB interface for touch control ●Back light control to lower power consumptionDescription (1)Features (1)1.On-Board resource (4)2.Working with Raspberry Pi (4)2.1.How to program Raspbian image file (4)2.2.Hardware connection (5)2.3.Screen touch calibration (5)2.3.1.Connecting to Raspberry Pi via SSH (5)2.3.2.Calibration steps (5)2.4.Virtual keyboard of Raspberry Pi (6)2.5.How to configure original Raspbian image file (7)2.5.1.How to installing driven script (7)2.5.2.How to enter graphical desktop (7)2.6.How to use with the Ubuntu system (7)3.How to use with BeagleBones (9)3.1.How to program Angstrom image file (9)3.2.Hardware connection (9)3.3.Screen touch calibration (9)4.How to use with Banana Pi (11)4.1.How to program Raspbian_For_BananaPi image file (11)4.2.Hardware connection (11)24.3.Screen touch calibration (11)4.3.1.Connecting to Banana Pi via SSH (11)4.3.2.Calibration steps (12)4.4.How to load WiFi driver of BananaPi Pro (13)4.5.How to use with the Lubuntu system (13)31.Figure 1: Switches and interfaces1 2 3 41)Backlight switch: it is used for backlight control (ON/OFF), working as a screen power button.2)HDMI: it is used for connecting the main board to the LCD screen.3)USB Touch Interface: USB touch/power interface.4)USB Power Interface: USB power interface (used only when the LCD is under power shortage). 2.Working with Raspberry Pi2.1.How to program Raspbian image fileIn order to use with Raspberry Pi, you should configure the original system first. Of course, you can program a ready-to-use system image file to your Raspberry Pi board as well. In this section, we will illustrate how to program the image file by taking the ready-to-use system image file,5inch_HDMI_B_RPI_Raspbian-150405.img, as an example. This image file supports Raspberry Pi Model B/B+/A+/2B.1)Copy the file with the expansion name .img to your PC;2)Connect a TF card to your PC, and format your TF card with the SDFormatter.exeNotices: The capability of TF card in used here should be more than 4GB. In this operation, a TF card reader is also required, which has to be purchased separately.3)Start the Win32DiskImager.exe, and select the system image file copied into your PC, then, click452.2.Hardware connection 1)Connect the LCD to the HDMI on the Raspberry Pi board with a HDMI cable; 2) Connect the USB Touch interface on the LCD to the USB interface on the Raspberry Pi board witha USB type-A male to micro-B cable.2.3.Screen touch calibration1) Enter the system terminal to calibrate the touch screen. The simple method is to connect akeyboard and a HDMI screen to the Raspberry Pi board, to enter the Graphical Desktop forcalibrating operation. However, some users may have no HDMI screen, so we present the SSH method for remote connection to the Raspberry Pi board. To use this method, you should make sure your PC and the Raspberry Pi board can find each other in the network. Normally, they can do so when connected to a same router.2) Open the software PuTTY, and enter the IP address of the Raspberry Pi board (you can enter therouter setting page on your PC to check the IP address). Then, set the Port to 22, and click the3) Enter the user name and the password:User Name: piPassword: raspberry4) When finished, you can enter the system terminal for operation.1)After connecting to the Raspberry Pi board, enter the following command under the terminal:DISPLAY=:0.0 xinput_calibratorAfter entering the calibration interface, there will be a prompt for four-point calibration shown in the screen:2)Click the points marked with the red cross pattern one by one to finish the touch calibration. 3) When finished, the system will generate a string of new calibration data, such as:Section “InputClass”Identifier “calibration”MatchProduct “ADS7843 TouchController”Option “Calibration”“253 3957 224 3820”EndSection4)Create a txt file on your PC, and copy the data above into the file for future use.5)Remove the calibration file in the system by the following command:sudo rm /etc/X11/xorg.conf.d/99-calibration.conf6)Create a new calibration file by the following command:sudo rm /etc/X11/xorg.conf.d/sudo mkdir /etc/X11/xorg.conf.dsudo nano /etc/X11/xorg.conf.d/99-calibration.conf7)When finished, the text editorNano will be run. Please paste the content in the new txt file intothe text editor.8)Yexit.9)Execute the command sudo reboot to restart the system. When finished, the touchconfiguration will be valid.2.4.Virtual keyboard of Raspberry PiThe Virtual keyboard of Raspbian system enables you to save the USB resource, providing easy system operations. After the LCD is working properly, this function can be invoked by the following command: DISPLAY=:0.0 matchbox-keyboard -s 100 extendedNow, the virtual keyboard is ready to use, as Figure 2 shows.Figure 2: Virtual keyboard of Raspberry Pi672.5. How to configure original Raspbian image fileIn the section above, we presented the steps of image programming by taking the ready-to-usesystem image file programming as an example (see Section 2.1), since the ready-to-use image is easier to use and understand. However, you can freely customize your system by configuring the original Raspbian image file to support this LCD module.1) Copy the file RPI2B_B_B+_USB_TOUCH_RES_5.0_RASPBIAN.tar.gz into the Raspbian system, andunzip it. That is, enter the terminal and input the following command:sudo tar zxvf RPI2B_B_B+_USB_TOUCH_RES_5.0_RASPBIAN.tar.gz2)Run the script USB_TOUCH_RES_5.0_RASPBIAN located at the folderRPI2B_B_B+_USB_TOUCH_RES_5.0_RASPBIAN by the following command: cd RPI2B_B_B+_USB_TOUCH_RES_5.0_RASPBIANsudo ./USB_TOUCH_RES_5.0_RASPBIAN3) When finished, the system will reboot automatically. And the LCD module can work properly,including display and touch functions, after the system rebooted.Notice: The Raspbian system boots to terminal interface by default. To make the operations simple when using with a LCD, it is recommended to set the system to boot to graphical desktop directly. Please follow the steps below to configure the system.1)Enter the Raspbian system, and input the following command: sudo raspi-config 2) Select the option Enable Boot to Desktop/Scratch by using the Arrow keys, Space key or/andEnter key.3)Select the option Desktop Login as user ‘Pi’ at the graphical desktop . 4) When you see the prompt “Would you like to reboot now?”, select the option Yes to reboot thesystem.2.6. How to use with the Ubuntu systemProgram the image file 5inch_HDMI_B_RPI_Ubuntu-150405.img to the board. This image file supports Raspberry Pi 2B.User Name: linaroPassword: linaroFor screen touch calibration, the corresponding operations are the same with that of Raspbian. For more detailed information, please refer to the Section 2.3.893. 3.1. How to program Angstrom image fileIf this LCD module is used for display only, you can program the latest Angstrom image file to the board directly without any change. The BeagleBone Black will read the display parameters of the 5 inch HDMI displayer and set the resolution to 800*480 automatically.When using this LCD module as a touch screen, you should program the image file5inch_HDMI_B_BB_Black_Angstrom-150424.img provided by the CD to the board. Please follow the steps below to program the image file.1)Copy the file with the expansion name .img to your PC; 2)Connect a TF card to your PC, and format your TF card with the SDFormatter.exe Notices: The capability of TF card in used here should be more than 4GB. In this operation, a TF card reader is also required, which has to be purchased separately.3) Start the Win32DiskImager.exe, and select the system image file copied into your PC, then, click4) and hold it till power up. Then, you will enter the system located at the TF card. And BeagleBone will take about 40 minutes to copy the system in the TF card into the on-board eMMC. When finished, the 4 LED indicators on the board will light up at a same time. After the systemrebooted, you can enter the graphical desktop directly.3.2.Hardware connection 1)Connect the LCD to the HDMI on the BeagleBone board with a HDMI to micro HDMI cable; 2) Connect the USB Touch interface on the LCD to the USB interface on the BeagleBone board withUSB type-A male to micro-B cable. (BeagleBone has two USB interfaces, one for host and the other for client. In here, you should connect the LCD module to the USB host interface).3.3.Screen touch calibration 1) Remove the calibration file in the system: /etc/pointercal.xinput .Explanation: Connecting a mouse to the board, you can perform any remove operations in the graphical desktop. For SSH connection, the user name is root , no password.2) After rebooted, the Pi will enter the calibration interface automatically before start the system.There will be a prompt for four-point calibration shown in the screen:3)Click the points marked with the red cross pattern one by one to finish the touch calibration;4)When finished, the system will write the new calibration data into the file /etc/pointercal.xinput.10114.Before powering up the Banana Pi, you should connect it to a LCD displayer properly, since the Banana Pi may read the resolution parameters of the LCD displayer on startup. And the connection should be remained till the Banana Pi enters the desktop. In this case, even if you disconnect the LCD displayer and reconnect it again to the Banana Pi, the LCD can still work properly.4.1. How to program Raspbian_For_BananaPi image fileProgram the image file 5inch_HDMI_B_BananaPi_Raspbian-150410.img to the borad. This image file supports the modules BananaPi Pro and BananaPi.1)Copy the file with the expansion name .img to your PC; 2)Connect a TF card to your PC, and format your TF card with the SDFormatter.exe Notices: The capability of TF card in used here should be more than 4GB. In this operation, a TF card reader is also required, which has to be purchased separately.3) Start the Win32DiskImager.exe, and select the system image file copied into your PC, then, click4.2.Hardware connection 1) Connect the LCD to the HDMI on the Banana Pi board with a HDMI cable; 2) Connect the USB Touch interface on the LCD to the USB interface on the Banana Pi board with adual micro USB cable.4.3.Screen touch calibration1) Enter the system terminal to calibrate the touch screen. The simple method is to connect akeyboard and a HDMI screen to the Banana Pi board, to enter the Graphical Desktop forcalibrating operation. However, some users may have no HDMI screen, so we present the SSH method for remote connection to the Banana Pi board. To use this method, you should makesure your PC and the Banana Pi board can find each other in the network. Normally, they can do so when connected to a same router.2) Open the software PuTTY, and enter the IP address of the Banana Pi board (you can enter therouter setting page on your PC to check the IP address). Then, set the Port to 22, and click the123) Enter the user name and the password:User Name: bananapiPassword: bananapi4) When finished, you can enter the system terminal for operation.1)After connecting to the Banana Pi board, enter the following command under the terminal:DISPLAY=:0.0 xinput_calibratorAfter entering the calibration interface, there will be a prompt for four-point calibration shown in the screen:2)Click the points marked with the red cross pattern one by one to finish the touch calibration. 3) When finished, the system will generate a string of new calibration data, such as:Section “InputClass”Identifier “calibration”MatchProduct “ADS7843 TouchController” Option “Calibration”“253 3957 224 3820” EndSection4)Create a txt file on your PC, and copy the data above into the file for future use. 5)Remove the calibration file in the system by the following command: sudo rm /etc/X11/xorg.conf.d/99-calibration.conf 6) Create a new calibration file by the following command:sudo rm /etc/X11/xorg.conf.d/sudo mkdir /etc/X11/xorg.conf.dsudo nano /etc/X11/xorg.conf.d/99-calibration.conf7)When finished, the text editorNano will be run. Please paste the content in the new txt file into the text editor. 8) Yexit.9) Execute the command sudo reboot to restart the system. When finished, the touchconfiguration will be valid.4.4.How to load WiFi driver of BananaPi ProComparing with the Banana Pi, the BananaPi Pro has added an on-board WiFi module. When using the BananaPi Pro, you can use SSH to connect to the Pi and execute the following command to load the WiFi driver:sudo modprobe ap62104.5.How to use with the Lubuntu systemProgram the image file 5inch_HDMI_B_BananaPi_Lubuntu-150410.img to the board. This image file supports the modules BananaPi Pro and BananaPi.User name: bananapiPassword: bananapiFor screen touch calibration, the corresponding operations are the same with that of Raspbian. For more detailed information, please refer to the Section 2.3.。
