下载文档原格式
KOSTA DELTA 達美手推割草機使用手冊目錄_____________________________________________________________________ 國際性的相關圖示 2注意事項 3使用時需遵循之程序 5如何安裝 6如何操作7如何保養8常見問題及解決方法9引擎操作及保養手冊10圖片附錄13產品保証書18國際性的相關圖示這些圖示會出現在產品器材或是使用手冊上，所以在使用前最好能瞭解這些圖示的意義及目的。
（一）安全性警告圖示：1.注意2.重要：操作機械前請閱讀使用手冊。
3.警告：有噴出物，旁觀者勿接近。
4.不要上下斜坡方向割草，要以左右穿越的方向割草。
5.危險：請勿踏入。
6.危險：勿將手腳放置轉動狀能的刀片中。
7.危險：勿將手腳放置轉動狀能的刀片中。
8.危險：維修前請拔掉火星塞接頭。
注意事項（一）一般操作1.閱讀、瞭解並實際遵循操作手冊所指示，在開始使用前，必需切確熟悉機械的操作，控制和正確的使用方法。
2.在使用前，先練習使用割草機，可以到比較空曠的草地練習操作、剎車、方向控制，還有刀片在緊急狀態下如何立即停止等操控，再關始除草。
3.在使用前徹底檢查割草機及其週圍環境，將附近的石頭、玩具、鐵絲、骨頭、樹枝等會被刀片吸進割草機並射出的物質清除乾淨。
4.割草前確認割草範圍無其他閒雜人等，若有人進入範圍則停止割草。
5.此割草機是設計單人使用，所以除草時，不該帶著旁人甚至是兒童，這對雙方都是非常危險的。
6.僅能讓熟悉割草機之操作的，有責任感的成人使用割草機。
7.當使用手動發動割草機時，雙腳要離刀片遠一點，穩穩站牢後再拉發動手把或是發動線，千萬不要為了抓得更牢，把發動線繞在手腕或是手指上，這是非常危險的。
8.不要將手或腳放置在使用中的刀片附近，甚至是刀片下方。
9.不要光著腳或是穿著拖鞋割草，最好穿鋼頭鞋，以防腳被刀片割傷。
10.使用割草機時一定要配戴護目鏡，以免眼睛受傷。
肩带、塑料刀片、2齿刀片、尼龙割草头、扳手、六角扳手、附件包（电池、充电器另售）充电式割草机UR013GZ01切割宽度回转数(RPM)主轴规格体积(长x 宽 x 高)净重金属刀片:锯片:尼龙绳割草头:粉碎刀片: 塑料刀片: 金属刀片:尼龙绳割草头:仅工具：使用尼龙绳割草头和BL4080F：255 mm (10")225 mm (8-7/8")450 mm (17-3/4")270 mm (8-7/8")305 mm (12")3,500-6,7003,500-5,000M10 x 1.25 LH1,863 x 690 x 546 mm 1,966 x 690 x 546 mm 5.9 - 7.2 kg (13.0 - 15.9 lbs.)无段变速电子制动恒定速度缓速启动标准附件：最大输出功率1.5kW(使用BL4080F)附件尼龙割草头部件号 199884-2绳线尺寸:2.7mm 型号: 105-M10L部件号 1911Y2-9绳线尺寸:2.7mm型号: 121-M10L锯片部件号 199872-9锯片直径.:225mm部件号 1911Y0-3防护罩 225 MG粉碎刀片部件号 199874-5部件号 1911Y1-1刀片直径: 270mm防护罩 MG塑料刀片切割宽度199868-0199870-3塑料刀片组件可更换塑料刀片305mm肩带总成舒适型部件号 122A37-4部件号 199378-7红色尺寸部件号2.7mmx15m 2.7mmx30m 2.7mmx180mE-01828E-01834E-01840四叶螺旋尼龙绳XGT 智能充电系统扫码查看视频40Vmax系列扫码查看视频满足专业人士需求充电式割草机UR013G无 刷 电 机主动反馈传感技术UR013G切割刀片刀片直径2齿刀片3齿刀片4齿刀片198345-9195299-1196895-8255mm（标配件）（标配件）（标配件）（标配件）扳机开关UR013G偏置自行车式把手确保了相当于35 mL等级的引擎工具功率与ø450mm尼龙切割头兼容主电源按钮模式选择按钮变速控制杆使用户能够调整到所需速度并保持速度。
深圳常用园林工具电机使用说明
随着城市化进程的加快，深圳的园林绿化建设也日益发展。
在园林绿化建设中，各种工具电机的使用十分普遍。
为了让大家更好地了解深圳常用园林工具电机的使用方法，现将相关说明如下：
一、割草机
割草机是园林工作中常用的电动工具，用于修剪草坪、草地等。
使用时应注意以下事项：
1.检查割草机的刀片是否锐利，并及时更换。
2.在使用前，应检查割草机的电源线是否破损，以及电源是否稳定。
3.使用时，应将割草机刀片调至适当高度，避免过高或过低。
4.使用完毕后，应及时清洁割草机，并存放在防潮、通风的地方。
二、电锯
电锯是一种用于砍伐、锯木等工作的电动工具。
使用时应注意以下事项：
1.在使用前，应检查电锯的刃口是否锋利，并及时更换。
2.使用时，应佩戴防护手套、护目镜等防护用品，避免安全事故。
3.使用时，应避免过度施力，以免损坏设备。
4.使用完毕后，应及时清洁电锯，并存放在防潮、通风的地方。
三、高压清洗机
高压清洗机是一种用于清洗墙面、地面等的电动工具。
使用时应注意以下事项：
1.在使用前，应检查清洗机的电源线是否破损，以及电源是否稳定。
2.使用时，应佩戴防护眼镜等防护用品，避免安全事故。
3.使用时，应遵守清洗机的操作说明，并注意安全距离，避免喷射方向对人体造成伤害。
4.使用完毕后，应及时清洁清洗机，并存放在防潮、通风的地方。
以上是深圳常用园林工具电机使用说明，希望能对大家有所帮助，更好地完成园林绿化建设工作。
骑乘式割草机Riding Mower用户手册U s e r M a n u a l前言亲爱的顾客，非常感谢您购买赛科集团生产的骑乘式割草机。
我公司凭借生产优质的草地维护机器及配件享誉欧洲及国际市场。
此用户手册涵盖了有关机器的安全装配、操作和保养的说明。
请认真学习此手册。
为保证您能够恰当便捷的使用机器从而保证机器的使用寿命，请严格遵守手册说明。
在没有阅读手册中所有的说明、禁条和建议前，请勿使用此机器。
为方便以后使用，请妥善保存此手册。
用户手册应被视为骑乘式割草机的一部分，售出割草机时请务必携带用户手册。
手册中符号的含义符号含义“注意”或“警告”可能损坏机器或是对使用者造成伤害显示重要的说明、性能、步骤或事件，这些都需要你在装配、操作、保养机器时多加注意并遵守的。
显示关于机器及其零配件有用信息。
参照手册前面部分图片。
此符号会与图片序号一同出现。
参照本手册其他章节或是另外一本手册。
一般此符号同被参照的章节名称一同出现。
方向参照左边和右边前半部分和后半部分L=左边，R=右边R=后半部分，F=前半部分1.技术信息1.1使用CROSSJET牌的AC92-18（21）或AC92-23 4X4是一款两轴骑乘式割草机，专为山区或非山区的有草覆盖的平地和坡地（最大坡度为18度）割草作业而设计，这些地区不能有异物如石头、掉落的树枝、骨头、坚硬的东西等。
适用于多年生长的被树莓、黑莓及其他各种杂草缠绕的植物。
任何在用户手册里未提及或提及但超范围的的操作都被视为与机器本身的预期使用目的或操作是相违背的，由此引起的机器损坏，生产厂家概不负责，此风险由使用者自己承担。
使用者还应遵守生产厂家有关机器操作、维修保养的规定，只有了解机器性能，了解潜在危险的人才能使用、保养、维修机器。
只可以使用生产厂家认可的配件。
使用其他配件，保修立即失效。
1.2骑乘式割草机主要部件骑乘式割草机（型号AC92-18，AC92-21或AC92-23 4x4）包括以下几个基本部分：1.2 （1）护罩和储藏室护罩由塑料和金属拼接而成，包含了蓄电池的储藏室。
杭州小型园林工具电机使用说明
1.本产品适用于小型园林工具，如电动剪草机、电动割草机等。
2. 在使用前，请仔细阅读本说明书，并按照说明书的要求正确操作。
3. 在使用过程中，确保电机外部清洁干燥，避免进入水分和灰尘。
4. 在接通电源前，请检查电源线是否损坏，以免发生电击事故。
5. 打开电源开关前，请确认工具装置牢固可靠并处于正常工作状态。
6. 在工作过程中，如发现异响或异味，请立即停止使用并检查故障原因。
7. 在使用完毕后，请关闭电源开关，并在清洁工具前拔掉电源插头。
8. 如需维修或更换配件，请联系售后服务中心，切勿私自拆卸或更换配件。
9. 本产品为小型家用电器，不可作为工业用途，不可长时间连续使用。
10. 本产品仅限于园林工具使用，禁止非法用途或用于非园林工具。
11. 在使用过程中，应保持警觉，避免因疏忽或不当操作造成人身或财产伤害。
12. 请妥善保管本说明书，以备日后参考。
P02 P15 P24Cordless Grass Trimmer ENFES2PRODUCT SAFETYWARNING: This product can expose you tochemicals including lead and Di(2-ethylhexyl) phthalate (DEHP) which are known tothe State of California to cause cancer and birthdefects or other reproductive harm. For moreinformation go to .IMPORTANT SAFETY INSTRUCTIONSWARNING: Read all safety warnings andinstructions. Failure to follow the warningsand instructions may result in electric shock, fireand/or serious injury.WARNING: Read all instructionsFOR ALL APPLIANCES1) Avoid Dangerous Environment - Don’t use appliancesin damp or wet locations.2) Don’t Use In Rain.3) Keep Children Away - All visitors should be kept at adistance from work area.4) Dress Properly - Do not wear loose clothing or jewelry.They can be caught in moving parts. Use of rubbergloves and substantial footwear is recommendedwhen working outdoors. Wear protective hair coveringto contain long hair.5) Use Safety Glasses - Always use face or dust mask ifoperation is dusty.6) Use Right Appliance - Do not use appliance for any jobexcept that for which it is intended.7) Don’t Force Appliance - It will do the job better and withless likelihood of a risk of injury atthe rate for which it was designed.8) Don’t Overreach - Keep proper footing and balance atall times.9) Stay Alert - Watch what you are doing. Use commonsense. Do not operate appliancewhen you are tired.10) Store Idle Appliances Indoors - When not in use,appliances should be stored indoors indry, and high or locked-up place - out of reach ofchildren.11) Maintain Appliance With Care - Keep cutting edgesharp and clean for best performance and to reducethe risk of injury. Follow instructions for lubricating andchanging accessories. Keep handles dry, clean, andfree from oil and grease.12) Check Damaged Parts - Before further use of theappliance, a guard or other part that is damagedshould be carefully checked to determine that it willoperate properly and perform its intended function.Check for alignment of moving parts, binding ofmoving parts, breakage of parts, mounting, and anyother condition that may affect its operation. A guardor other part that is damaged should be properlyrepaired or replaced by an authorized service centerunless indicated elsewhere in this manual.FOR ALL BATTERY – OPERATED GARDENING1. Prevent unintentional starting. Ensure the switch is inthe off-position before connecting to battery pack,picking up or carrying the appliance. Carrying theappliance with your finger on the switch or energizingappliance that have the switch on invites accidents.2. Disconnect the battery pack from the appliance beforemaking any adjustments, changing accessories, orstoring appliance. Such preventive safety measuresreduce the risk of starting the appliance accidentally.3. Recharge only with the charger specified by themanufacturer .A charger that is suitable for one type ofbattery pack may create a risk of fire when used withanother battery pack.4. Use appliances only with specifically designatedbattery packs. Use of any other battery packs maycreate a risk of injury and fire.5. When battery pack is not in use, keep it away fromother metal objects, like paper clips, coins, keys, nails,screws or other small metal objects, that can make aconnection from one terminal to another. Shorting thebattery terminals together may cause burns or a fire.6. Under abusive conditions, liquid may be ejected fromthe battery; avoid contact. If contact accidentallyoccurs, flush with water. If liquid contacts eyes,additionally seek medical help. Liquid ejected from thebattery may cause irritation or burns.7. Do not use a battery pack or appliance that is damagedor modified. Damaged or modified batteries mayexhibit unpredictable behavior resulting in fire,explosion or risk of injury.8. Do not expose a battery pack or appliance to fireor excessive temperature. Exposure to fire ortemperature above 130°C may cause explosion.9. Follow all charging instructions and do not charge thebattery pack or appliance outside of the temperaturerange specified in the instructions. Chargingimproperly or at temperatures outside of the specifiedrange may damage the battery and increase the risk offire.10. Have servicing performed by a qualified repair personusing only identical replacement parts. This will ensurethat the safety of the product is maintained.11. Do not modify or attempt to repair the appliance or thebattery pack (as applicable) except as indicated in theinstructions for use and care.ADDITIONAL SAFETY RULESFOR LAWN TRIMMER ANDEDGE TRIMMER1. Keep guards in place and in good working order.2. Keep hands and feet away from cutting area.3. Do not use heavier lines than recommended in thismanual.4. Do not use line materials of other types – for example,metal wire, rope, and the like.SAFETY WARNINGS FORBATTERY PACKa) Do not dismantle, open or shred battery pack.b) Do not expose battery pack to heat or fire. Avoidstorage in direct sunlight.c) Do not short-circuit a battery pack. Do not storebattery packs haphazardly in a box or drawerwhere they may short-circuit each other or beshort-circuited by other metal objects. Whenbattery pack is not in use, keep it away from othermetal objects, like paper clips, coins, keys, nails,screws or other small metal objects, that can make aconnection from one terminal to another. Shorting thebattery terminals together may cause burns or fire.d) Do not remove battery pack from its originalpackaging until required for use.e) Do not subject battery pack to mechanical shock.f) In the event of battery leaking, do not allow theliquid to come in contact with the skin or eyes. Ifcontact has been made, wash the affected areaCordless Grass TrimmerENCordless Grass TrimmerENENCOMPONENT LIST1.BATTERY PACK *2.ON/OFF SWITCH3.UPPER SHAFT4.HANDLE ADJUSTMENT KNOB5.LOWER SHAFT6.SAFETY GUARD7.LINE FEED BUTTON8.LINE CUTTER9.AUXILIARY HANDLE 10.LOCK OFF SWITCH11.BATTERY INDICATOR LIGHT 12.CUTTING HEAD (SEE FIG.I)13.SPOOL CAP (SEE FIG. J)14.CAP RELEASE LATCH (SEE FIG.J)* Not all the accessories illustrated ordescribed are included in standard delivery.TECHNICAL DATACharging time (approx.)Battery pack:2.0Ah (1pc)2.0Ah (2pcs)65mins 130mins /Machine Weight6.4 lbs4.7 lbs**Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.*** Charger output 1 and output 2 mean two ports with the same output voltage and current.ACCESSORIESWG183WG183.9Battery pack (WA3525)2/Charger (WA3770)1/Spool (WA0007)11Spool cap(WA0216)11Safety guard 11Auxiliary handle11Only use the appropriate accessories intended for this tool. AccessoryClick!A D3D121132D2C B21321213GED4F 13141212KIOne click!H13141516JN PL KOM9ENCordless Grass TrimmerASSEMBLY & OPERATIONACTIONFIGUREAssemblyAssembling the Trimmer Shaft See Fig. A Assembling the Auxiliary Handle See Fig. B Assembling the Safety Guard See Fig. CInstalling and Removing the Battery PackNOTE:• This machine will only run when 2 batteries are installed. It is recommended to use the same two batteries and charge the two batteries at the same time.• When you use two batteries with different power, the machine will only run to the lower common denominator.See Fig. D1, D2Charging the battery pack NOTE:• The batteries are shippeduncharged. Each battery must be fully charged before the first use.• Always fully charge the two batteries at same time. More details can be found in charger’s manual.See Fig.D3Battery power indicator on the machineSee details in BATTERY STATUS section See Fig.D4OPERATIONOn/Off SwitchWARNING! The cutting headcontinues to rotate after the trimmer has been switched off; wait until it has completely stopped then lay down the tool.See Fig. E TrimmingSee Fig. F -Adjusting the Auxiliary handle See Fig. G Manually feeding the line See Fig. H Removing the Cap See Fig. I Cutting HeadSee Fig. J Changing the line spoolSee Fig.K,L Manually winding the lineSee Fig. M,N,O,PBATTERY STATUS (See Fig. D4)Before starting or after use, press the button beside the power indicator light on the machine to check the battery capacity. During operation, the battery capacity will be indicated automatically by the battery power indicator.The indicator constantly senses and displays the battery condition as follows.For the machine with 2 battery packs with different power, the power indicator light displays the battery condition with the lower one of the two batteries.Battery power indicator status Battery conditionFive green lights () areilluminated.The two batteries are in a highly charged condition.Two, three or four green lights are illuminated.The two batteries have a remaining charge. The more lights are illuminated, the more battery capacity.QP10ENOPERATION INSTRUCTIONSWARNING! The charger and battery pack are specially designed to work together so do notattempt to use any other devices. Never insert or allow metallic objects into your charger or battery packconnections because of an electrical failure and hazard will occur.1.AUTOMATIC LINE FEED SYSTEMWhen initially switching on the trimmer, a small length of line is fed out.A ‘clattering’ noise will be heard for a short time. This is normal and is caused by the line being cut by the line cutter. Once the line is cut to the correct length, the‘clattering’ noise will stop and the trimmer motor will run at full speed.To feed more line, stop the trimmer completely, thenrestart, allowing the motor to reach full speed. Repeat this until you hear the ‘clattering’ noise of the line cutting. (Do not repeat this procedure more than 6 times)2 . MANUALLY FEEDING THE LINE (See Fig. H)Press and release manual line feed button, whilst gently pull out the lines until the lines reaches the line cutter. When the required amount of line is fed out, gently pull on the second line (there is no need to press the manual line feed button again). If the line extends past the line cutter, too much line has been fed out. If too much line is fed out, remove the spool cap and rotate the spool anti-clockwise until the line is at the desired length.Removing the Cap (See Fig. I)Press and hold in the two latches. Pull the spool cap away from the Cutting Head. Keep the cap and spool holder clean from debris. To replace the cap, press itfirmly towards the spool holder. Ensure that it is correctly connected by trying to remove it without depressing the two latches.Changing the Line Spool (See Fig. K, L)First take off the cap and remove the old spool. Place new spool into cutting head. Feed one line through the eyelet, then repeat for second line (See Fig. L).Release line from cleat on the Spool. Reattach the cap.WARNING! Your Trimmer is designed to only use line with a maximum diameter of 0.065”(1.65mm). Only use nylon line.IMPORTANT - Always wind the line onto the upper section of the spool first.3. MANUALLY WINDING THE LINE (SEE FIG.M, N, O, P)Take approximately 16ft (5 m) line and insert 5/8” (15 mm) of line into one of the holes in the upper section of the spool. Wind the line in the direction of the arrows on the top of the spool.Leave approximately 3.9’’ (100 mm) of line unwound and place it into the cleat. Repeat on the lower section of spool. Care should be taken to ensure that the line is neatly coiled on the spool. Failure to do so will impair the efficiency of the automatic line feed. Then fit the spool as described above in “Changing the Line Spool”.STORING YOUR GRASS TRIMMERAlways remove the battery pack from your trimmer after use.T o store your grass trimmerThe trimmer is provided with a hanging slot for storing the trimmer on the wall. (See Fig. Q)Store in a dry place where the trimmer and battery can be protected from damage.MAINTENANCEAlways remove the battery pack from your trimmer after use.Always check the product prior to being used for any damage.After use, disconnect the battery from the tool and check for damage.Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry room temperature location. Keep the motor ventilation slots clean. Keep all working controls free of dust.FOR BATTERY TOOLSThe ambient temperature range for the use and storage of tool and battery is 0℃-45℃.The recommended ambient temperature range for the charging system during charging is 0℃-40℃.Cordless Grass TrimmerEN。
剪草机的使用方法嘿，你问剪草机的使用方法？这可不难哦。
首先呢，你得把剪草机准备好。
检查一下机器有没有损坏啥的，要是有问题可不能用哦。
看看刀片是不是锋利，要是钝了就得磨一磨。
就像你要去砍柴，得先看看斧头锋不锋利一样。
然后呢，把要剪的草地清理一下。
把石头啊、树枝啊这些东西都捡走，不然会弄坏剪草机。
就像你睡觉前要把床上的杂物清理掉，不然会睡得不舒服。
接着，给剪草机加上油。
这就像给汽车加油一样，没有油可跑不动哦。
加好油后，启动剪草机。
启动的时候要小心点，别把手给弄伤了。
开始剪草啦。
推着剪草机慢慢地走，不能走得太快，不然剪得不均匀。
就像你走路不能跑太快，不然会摔跤一样。
剪草的时候要注意方向，最好是来回剪，这样剪得更干净。
如果遇到比较高的草，可以多剪几遍。
不能一下子就想把高草剪平，那样会很费劲，还可能会弄坏剪草机。
就像你吃硬东西的时候，要慢慢咬，不能一口就吞下去。
剪完草后，要把剪草机清理干净。
把刀片上的草屑擦掉，把机器上的灰尘吹掉。
这样下次用的时候就会很干净，也不容易坏。
我记得有一次，我看到邻居家的草地长得很高了，他就拿出剪草机来剪草。
我在旁边看着，觉得很有趣。
他按照上面的方法，一步一步地剪草，不一会儿就把草地剪得整整齐齐的。
从那以后，我就知道了剪草机的使用方法。
总之呢，剪草机的使用方法就是准备好机器，清理草地，加油启动，慢慢剪草，注意高草多剪几遍，剪完清理机器。
就像做一件小事，得认真仔细才能做好。
咋样，明白了不？。
O wner’s ManualInstructions for Assembly and TestingTow package for a Stump and Root Grinder (Used on NorthStar Stump Grinder 296020)Any Questions, Comments, Problems, or Parts Orders Call NorthStar Product Support @ 1-800-270-0810Safety Label Location (4)Machine Components Identification (5)Towing Instructions (6)Specifications (8)Parts Breakdown – Exploded View (9)Safety Instructions (10)Unpacking (11)Assembly Instructions (12)Limited Warranty (15)California Proposition 65 Information (16)Safety Decal LocationsTo order replacement safety label part #785623, call NorthStar Product Support at 1-800-270-0810.WARNINGALWAYS make sure safety labels are in place and in good condition. If a safety label ismissing or not legible, order new labels.Machine Components Identification1.)Tow Bar. Connects the Stump Grinder to the tow vehicle.2.)2” Coupler. Allows the trailer unit to be hooked up to a 2” ball hitch.3.)Safety Cables. Secures trailer to vehicle in case of accidental disconnection of ball and coupler.4.)Tow Bar Socket. Connects the Tow Bar to the Stump Grinder5.)Hitch Pin. Locks tow bar into Tow SocketAll grinder units can be transported via trailers, or with the purchase of an optional towing kit package can be towed behind the vehicle.Now that you have installed the Stump Grinder Tow Package, there is some important safety information you need to know with regard to vehicle handling with the Stump Grinder attached.Step One. Inspect/RepairImportant safety rules:•Replacement parts.If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement parts that do not meet specifications may result in a safety hazard or poor operation.Step Two. TowingMaximum Towing Speed…………….45 MPHCoupler Size………………………….2” BallOverall Dime nsions (boxed)…….…...39.5”L x 7”W x 4.5 ”HWeight (shipping)………………….…20 lbs.The manufacturer reserves the right to make improvements in design and/or changes in specifications at any time without incurring any obligation to installthem on units previously sold.Any Questions, Comments, Problems, or Parts OrdersCall NorthStar Product Support @ 1-800-270-0810Safety in Moving and Towing the Stump GrinderSafety – Before UseAlways inspect your Stump Grinder before each use, and repair as needed, to keep it in safe working condition:•Read manual. Do not allow anyone to tow the Stump Grinder who has not read the Owner’s Manual.•Review safety rules. Before towing this Stump Grinder, review the instructions for safe towing. Failure to follow these instructions may result in serious injury to the operator or bystanders.•Mechanical parts. Check to be sure all nuts and bolts are tight to make sure the Stump Grinder is in safe working condition.•Tires. Be sure tires are fully inflated and in good repair before towing the Stump Grinder. When adding air to tires, do not over-inflate -- serious injury could occur if tire explodes.Safety During Towing•Read instructions. Review towing safety instructions in your towing vehicle manual.•Securely attached. Be sure the Stump Grinder is securely attached to the towing vehicle before towing. •Tires. Be sure tires are fully inflated and in good repair before towing the Stump Grinder. When adding air to tires, do not over-inflate -- serious injury could occur if tire explodes.•Added length. Be aware of the added length of the Stump Grinder.•Speed limit. Never tow this Stump Grinder over 45 mph. Faster speeds may result in loss of control. •Rough terrain. Be extra cautious and drive slowly when traveling over rough terrain.•Under the influence. Never tow this Stump Grinder while under the influence of alcohol, drugs, or medication.•On public roads. If towing on a public road, make sure to comply with all local, state, and federal towing requirements. It is the sole responsibility of the purchaser to obtain licensing, trailer lights, safety chains or signage, as needed to comply.•Unattended. Turn off the towing vehicle before leaving the Stump Grinder unattended.•Disconnect before operate. Do not use the Stump Grinder while it is connected to the towing vehicle.Safety – After use•Periodic maintenance. Perform periodic maintenance as directed in this manual to keep the Stump Grinder in safe working condition.Closely inspect all contents in the shipping carton.•If you have missing or damaged components: Contact NorthStar Product Support at 1-800-270-0810.Assembly Instructions12Step 1▪Attach Tow Bar Socket to Stump Grinder Using (4) 3/8” x 1-1/4” Bolts and (4) 3/8” Class G Locking Nuts. ▪ Tighten Bolts to 19 lb-ft torque.Step 2▪ Attach coupler to Tow Bar by using (2) 1/2” x 3” bolts and (2) 1/2” Class G Flange Nuts.▪ Tighten Bolts to a 90 lb-ft torque.Step 3▪ Attach (2) Safety Cables to Stump Grinder by attaching to the Mounting Holes on the Stump Grinder Frame.3/8” lock nut3/8” boltTow bar socketFig 035341/2” boltTow Bar2” coupler1/2” lock nutFig03535Safety cablesMount holesFig03536& Fig03537Assembly Instructions cont’d13WARNING• Remove safety cables from stump grinder before operatingStep 4▪ Slide the Tow Bar into the Tow Bar Socket and secure with Hitch Pin. ▪ Lock Hitch Pin into position using cotter pin. Hitch PinCotter PinTow BarTow Bar SocketFig03531This page has intentionally been left blank.14Dear Valued Customer:The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance. Please thoroughly read the instructions and understand the operation before using your product.Limited WarrantyNorthStar shall warranty any piece of equipment manufactured, or parts of equipment manufactured, to be free from defects in material or workmanship for a period of 90 days for noncommercial/nonrental use and a period of 90 days for commercial/rental use from the date of purchase by user.NorthStar shall warranty any wear item, including, but not limited to, valves, seals, pump diaphragms, hoses, and filter elements to be free from defects in material or workmanship for a period of 90 days from the date of purchase by user. This warranty applies to the original purchaser of the equipment and is non-transferable. Verification of purchase is the responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the equipment has failed due to lack of proper maintenance. Any misuse, abuse, alteration or improper installation or operations will void warranty. Determining whether a part is to be replaced or repaired is the sole decision of NorthStar.NOTE: Some services performed by parties other than NorthStar may void warranty.This warranty covers parts only. It will not provide for replacement of complete products due to defective parts. Components not manufactured by NorthStar are guaranteed by their manufacturer and can be serviced at factory-authorized locations near you. Any costs incurred due to replacement or repair of items outside of a NorthStar approved facility is the responsibility of the buyer and not covered under warranty. NorthStar can supply you with the service center location in your area.This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, windstorm, acts of God, applications not approved by NorthStar in writing, corrosion caused by chemicals, use of replacement parts which do not conform to manufacturer’s specifications, and damage caused by vandalism. Additional exclusions: loss of running time, inconvenience, loss of income, or loss of use, including any implied warranty of merchantability of fitness for a specific use.Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical contact by the public. This warranty does not cover any personal injury or damage to surrounding property caused by failure of any part.This warranty is in lieu of any other warranty expressed or implied and NorthStar assumes no other responsibility or liability outside that expressed within this warranty.Please fill in the following information and have it on hand when you call in on a warranty claim.Customer Number: ______________________________________________________________Date of Purchase: _______________________________________________________________NorthStar Serial Number: ________________________________________________________Item Number: __________________________________________________________________1516。
