axxon B-2300单页

P.O. BOX 44994 •MADISON WI 53744.4994 •PHONE: +1.608.441.2323 •TOLL FREE: 800.700.2282GRASON-STADLER NICOLET BIOMEDICAL NICOLET VASCULAR TOENNIESPRODUCT SPECIFICATIONS November 2004 | GSI TympStar | 2000-0112 Rev1The following specifications apply to both Version 1and Version 2 of the GSI TympStar. > Bold arrowed type indicates the additional capabilities of Version 2.GENERAL SPECIFICATIONS W x D x H: 52 cm x 38 cm x 32 cm Weight: 7.5 Kg Shipping Weight: 13.4 Kg Power Consumption: 120 Watts maximum Test Types: Tympanometry, Acoustic Reflex Threshold,Reflex Decay, Eustachian T ube Function (Intact & Perforated )Protocols: Diagnostic, Screening, User-defined > Special Tests: Two-component T ympanometry,Multiple Frequency T ympanometry, Acoustic Reflex Latency Test, Reflex Sensitization Display: Internal or External VGA Monitor Interface: RS232, parallel and keyboard output Printout: Internal or External Deskjet or Laserjet Printer PROBE TONE 226 Hz (85 dB SPL ±1.5 dB)> 678 Hz (85 dB SPL ±3.0 dB)> 1000 Hz (75 dB SPL ±3.0 dB)Accuracy: ±1%Harmonic Distortion: Less than 5%ADMITTANCE MEASUREMENTS Range: 226 Hz (-1.0 to +7.0)> 678 Hz (-5.0 to +25)> 1000 Hz (-5.0 to +30)Sensitivity Scale: Auto Scales to Appropriate Range,Manual selection also possible in Reflex Modes only Accuracy (226 Hz): Tymp Mode: ±5% of reading or ±0.1 ml, whichever is greater Reflex Mode: ±5% of reading or ±0.2 ml, whichever is greater PRESSURE MEASUREMENTS (load volume of 0.2 to 7.0 ml)Range:Normal = +200 to -400 daPa Wide = +400 to -600 daPa Accuracy: ±10% of reading or ±10 daPa, whichever is greater Sweep Rate: 12.5, 50.0 and 600/200 daPa/sec, > 200 daPa/sec.Sweep Accuracy: 10% of nominal rate Maximum limits (in 0.5cc cavity ): -800 daPa & +600 daPa REFLEX MEASUREMENTS Stimuli: > 250, 500, 1k, 2k, 4k, BBN, LBN, HBN,> Click (100 microseconds pulse), External Input,Non-acoustic Frequency Accuracy: ±3%Harmonic Distortion (THD): Less than 5% (measured acoustically)Noise Signals: (3 dB bandwidths)Low Band: 125 -1,600 Hz High Band: 1,600 -4,000 Hz Broad Band: 125 -4,000 Hz Intensity Range: 35 to 120 dB HLStep Size: 5 dB, >1 dB and 2 dB Calibration Accuracy: ±3 dB Step Accuracy: ±0.5 dB ON/OFF Ratio: 70 dB minimum ENVIRONMENTAL Temperature:Storage: -40°C to +75°C Operating: +15°C to +35°C Humidity: 90% at 35°C (non-condensing)ACCESSORIES SUPPLIED Probe assembly (including contralateral insert phone)Eartips (1 pkg. each standard, special, screening)Printer paper, 2 rolls thermal, 1 roll self-adhesive Calibration test cavity, Cleaning kit, Probe mount kit (shoulder, clip, wrist band), Quick User Guide,Reference Instruction Manual, Remote (RS232 link)Dust CoverOPTIONAL ACCESSORIES Deskjet printer 1700-9613External VGA monitor 1700-9614External keyboard 1700-9615Isolation Transformer 1700-9617Service Manual 2000-0110Conversion Kit 2000-9650(V1 to V2)LANGUAGE KITS GSI TympStar Version 1English 2000-9645E French 2000-9645F German 2000-9645G Spanish 2000-9645S Italian 2000-9645I GSI TympStar Version 2English 2000-9646E French 2000-9646F German 2000-9646G Spanish 2000-9646S Italian 2000-9646I QUALITY SYSTEM Manufactured, designed, developed and marketed by VIASYS Healthcare Inc. NeuroCare Group under ISO 13485, ISO 9001 certified quality system.COMPLIANCE / REGULATORY STANDARDSDesigned, tested and manufactured to meet the following domestic (USA), Canadian, European and International Standards:UL 2601-1American Standards for Medical Electrical Equipment. IEC 601-1, EN 60601-1International Standards for Medical Electrical Equipment.CSA C22.2 # 601-1-M90Medical Device Directive (MDD) (ID No.: 0344) to comply with “EC Directive” 93/42/EECANSI S3.39, ANSI S3.6, IEC 645-1, IEC 1027, ISO 389GSI TYMPSTAR ™Middle Ear Analyzer。

尺寸换算纸张及照片_英寸_英尺_厘米照片、名片、纸张尺寸等大全1英寸25mm×35mm2英寸35mm×49mm3英寸35mm×52mm港澳通行证33mm×48mm赴美签证50mm×50mm日本签证45mm×45mm大二寸35mm×45mm护照33mm×48mm毕业生照33mm×48mm身份证22mm×32mm驾照21mm×26mm车照60mm×91mm数码相机和可冲印照片最大尺寸对照表500万像素有效4915200，像素2560X1920。

可冲洗照片尺寸17X13，对角线21英寸400万像素有效3871488，像素2272X1704。

可冲洗照片尺寸15X11，对角线19英寸300万像素有效3145728，像素2048X1536。

可冲洗照片尺寸14X10，对角线17英寸200万像素有效1920000，像素1600X1200。

可冲洗照片尺寸11X8，对角线13英寸130万像素有效1228800，像素1280X960。

可冲洗照片尺寸9X6，对角线11英寸080万像素有效786432，像素1024X768。

可冲洗照片尺寸7X5，对角线9英寸050万像素有效480000，像素800X600。

可冲洗照片尺寸5X4，对角线7英寸030万像素有效307200，像素640X480。

可冲洗照片尺寸4X3，对角线5英寸5寸照片（3X5），采用800X600分辨率就可以了6寸照片（4X6），采用1024X768分辨率7寸照片（5X7），采用1024X768分辨率8寸照片（6X9），采用1280X960分辨率按照目前的通行标准，照片尺寸大小是有较严格规定的1英寸证明照的尺寸应为3．6厘米×2．7厘米；2英寸证明照的尺寸应是3．5厘米×5．3厘米；5英寸（最常见的照片大小）照片的尺寸应为12．7厘米×8．9厘米；6英寸（国际上比较通用的照片大小）照片的尺寸是15．2厘米×10．2厘米；7英寸（放大）照片的尺寸是17．8厘米×12．7厘米；12英寸照片的尺寸是30．5厘米×25．4厘米。

特性⏹⏹⏹⏹⏹⏹⏹⏹⏹⏹⏹⏹⏹⏹应用耗23 mA发射电流。

QFN16 (3x3) 超低功耗Sub-1GHz射频收发器目录1.电气特性 (4)1.1推荐运行条件 (4)1.2绝对最大额定值 (4)1.3功耗 (5)1.4接收机 (6)1.5发射机 (7)1.6稳定时间 (8)1.7频率综合器 (8)1.8晶体 (9)1.9低频振荡器 (9)1.10低电压检测 (9)1.11数字接口 (10)1.12典型参数图表 (11)2.管脚描述 (16)3.典型应用原理图 (18)3.1直接(Direct Tie) 原理图. (18)3.2射频开关(Switch Type) 原理图. (19)4.功能描述 (21)4.1发射机 (21)4.2接收机 (22)4.3辅助功能 (22)4.3.1上电复位（POR） (22)4.3.2晶体振荡器 (23)4.3.3睡眠计时器 (23)4.3.4低电压检测 (23)4.3.5接收信号强度指示器(RSSI) (23)4.3.6相位跳变检测（PJD） (24)4.3.7自动频率控制（AFC） (25)4.3.8数据率时钟恢复（CDR） (25)4.3.9快速手动跳频 (25)5.芯片运行 (26)5.1SPI接口 (26)5.2FIFO (26)5.2.1FIFO 读写时序 (27)5.2.2FIFO 相关中断 (27)5.3工作状态，时序及功耗 (28)5.3.1启动时序 (28)5.3.2工作状态 (29)5.4GPIO和中断 (30)6.数据包及包处理机制 (33)6.1直通模式 (33)6.2数据包模式 (34)7.超低功耗运行 (36)7.1Duty Cycle 运转模式 (36)7.2超低功耗（SLP）接收模式 (36)7.3接收机“电流VS性能”配置 (37)8.用户寄存器 (38)9.订购信息 (40)10.封装信息 (41)11.顶部丝印 (42)12.文档变更记录 (43)13.联系信息 (44)1. 电气特性V DD= 3.3 V，T OP= 25 °C，F RF = 433.92 MHz，灵敏度是通过接收一个PN9 序列及匹配至50 Ω阻抗下，0.1％BER 的标准下测得。

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.materialS:Stiles c—3/4'' (19mm) thick, Solid Color Reinforced Composite with GraffitiOff ™ surface thermoset and integrally fused into one homogenous piece. Surface, edge, core are to be the same color. Leveling device: 7 gauge, 3/16" (5mm) thick, corrosion-resistant, chromate-treated, double zinc-plated steel angle leveling bar bolted to stile; furnished with 3/8'' (10mm) stainless steel diameter threaded wedge anchor, hex nuts, lock washer, flat washers, and shoe retainers. Shoe: 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish; 4'' (102mm) high.Panels —1/2'' (13mm) thick, Solid Color Reinforced Composite with GraffitiOff ® surface thermoset and integrally fused into one homogeneous piece. Surface, edge, core are to be the same color.doors —3/4'' (19mm) thick, Solid Color Reinforced Composite with GraffitiOff ® surface thermoset and integrally fused into one homogeneous piece. Surface, edge, core are to be the same color.Posts (for 1093 Series screens only) — 1-1/4'' (32mm) square tubing; 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. Floor and ceiling connections are constructed of 18-8 S, type-304, heavy-gauge stainless steel. Furnished in 10-ft (305-cm) lengths; to be cut in field to job specifications.Headrail (for 1092 Series compartments only) —Extruded anodized aluminum with satin finish. Enclosed construction with sloping top. Face has raised grip-resistant edge.Designer's Notes: Headrails with integral curtain tracks and hooks are available for compartments without doors. Optional vinyl curtains are available.Wall Posts —1" x 1-1/2" (25 x 38mm) tubing; 18-8 S, type-304, 16-gauge (1.6mm) stainless steel with satin-finish. 58" (147cm) high, pre-drilled for door hardware.Heavy-duty Hardware (standard) — Hinges, door latches, door keepers, clothes hooks, door stop plates, and mounting brackets are constructed of 18-8 S, type-304, heavy-gauge stainless steel with satin finish. Threaded inserts are factory installed for securing hinges, door stop plates, and door latches. Theft-resistant, stainless steel pin-in-head Torx screws are furnished for door hardware and all mounting brackets. Barrel hinge is adjustable to adjust door swing of unoccupied toilet compartment from partially open to fully closed. Toilet compartment door is locked from inside by sliding door latch into keeper. Threaded inserts are factory installed to secure door hinges, latch and door stops. Two door stops prevents door from being kicked in/out beyond stile by vandals. Mounting screws for stile to panel bracket, latch keeper, and coat hook connections are through-bolted.institutional Hardware (.67 option) —Hinges, door latches, door keepers, clothes hook, U-channels, door stop plates and angle brackets are constructed of 18-8 S, type-304, heavy-gauge stainless steel with satin finish: one-piece, full-height hinge is 16 gauge (1.6mm); one-piece door keeper is 11 gauge (3.2mm);one-piece, full-height U-channels and angle brackets are 18 gauge (1.2mm). U-channels secure panels to stiles, and angle brackets secure panels and stiles to walls. Door latch slides on a shock-resistant nylon track. Two door stops prevent door from being kicked in/out beyond stile by vandals. Theft-resistant, stainless steel pin-in-head Torx screws are furnished for door hardware, U-channels, and angle brackets. Doors are equipped with a self-closing hinge. Threaded inserts are factory installed to secure door hinge, latch, and doorstops. Mounting screws for stile-to-panel brackets and latch keeper connections are through-bolted. To specify institutional hardware, add suffix .67 to series number. Example: specify 1092.67 for overhead-braced partitions furnished with institutional hardware, including factory-installed threaded inserts for door hardware attachment.inStallation:Bobrick installation instructions are packed with each shipment and are available also in advance on request.notes:1. Ceiling-hung and floor-to-ceiling toilet compartments require structural members (not furnished by Bobrick) in ceiling. For suggested types of ceiling supportsystems, see Bobrick Advisory Bulletin TB-32.2. Wall backing is required to secure the mounting brackets of panels, stiles, and wall posts. For suggested wall backing, see Bobrick Advisory Bulletin TB-46.3. Floor-anchored stiles are furnished with expansion shields and threaded rods. The expansion shields require minimum 2'' (50mm) penetration into minimum3'' (75mm) thick structural concrete.4. Bobrick stainless steel partition-mounted washroom accessories are available for mounting in panels between two compartments. See current Bobrick Catalogfor description of accessories. Cutouts in panels can be pre-cut for Bobrick models at factory if location and size of all cutouts and Bobrick model numbers are furnished at time of order.GUarantee:Bobrick toilet partitions including all hardware and mounting brackets are guaranteed to be free from defects in material and workmanship for a period of one year from date of purchase. Any products returned to Bobrick under this guarantee will be repaired or replaced at no charge. 10-Year Warranty: Bobrick ex-tends a ten-year limited warranty from date of purchase for SierraSeries® Solid Color Reinforced Composite partition panels, doors, and stiles against breakage, warpage, delamination and corrosion when materials are properly installed, and normally used.SpeCiFiCation:Water-resistant, solid color reinforced composite ____________________ (insert one: toilet partitions, dressing compartments, shower dividers, urinal screens) shall be _______________ (insert one: overhead-braced toilet partition or floor anchored, wall-hung, post-to-ceiling urinal screens). Stiles, panels and doors shall be constructed of Solid Color Reinforced Composite with GraffitiOff ® surface thermoset and integrally fused into one homogeneous piece. Surface, edges and core are to be same color. Solid Color Reinforced Composite material shall be covered by a 10-year limited warranty against breakage, warpage, corrosion, and delamination. Stiles and doors shall be 3/4'' (19mm) thick; panels shall be 1/2'' (13mm) thick. All units shall meet ICC and NFPA Class B or UBC Class II, ASTME 84 Fire-Resistance Standards. Stiles shall have leveling device that is concealed by a one-piece, type-304, satin-finish stainless steel shoe that is 4'' (102mm) high.Stiles, panels and doors shall be __________ (insert color name and number from current Bobrick catalog). Headrails for overhead-braced compartments shall be anodized aluminum with satin finish. **All door hardware and mounting brackets shall be type-304 stainless steel with satin finish. All doors shall be supplied with three hinges. Threaded inserts shall be factory installed for securing door hinges, latches and door stops. Theft-resistant, stainless steel pin-in-head Torx screws shall be furnished for door hardware and all mounting brackets. Through bolts shall be used for securing latch keeper, clothes hook and panel-to-stile brackets. A clothes hook shall be furnished for each door with heavy duty hardware option. Hinges shall be adjustable to hold doors of unoccupied compartments partially open or fully closed. Two door stops shall be furnished for each door to prevent it from being kicked in/out beyond stile by vandals. Manufacturer's service and parts manual shall be provided to the building owner/manager upon completion of project.**To specify Institutional hardware, replace end of specification paragraph with: .67 option All door hardware, U-channels, and angle brackets shall be type-304 stainless steel with satin finish: one-piece, full-height hinges shall be 16 gauge (1.6mm); one-piece door keepers shall be 11 gauge (3.2mm); one-piece, full-height U-channels and angle brackets shall be 18 gauge (1.2mm). U-channels shall be furnished to secure panels to stiles, and angle brackets furnished to secure panels and stiles to walls. Doors shall be equipped with a self-closing hinge. Two door stops shall be furnished for each door to prevent it from being kicked in/out beyond stile by vandals. A clothes hook shall be furnished for each door. Theft-resistant, stainless steel pin-in-head, Torx screws shall be furnished for door hardware, U-channels, and angle brackets. Through bolts shall be used for securing latch keeper and panel- to-stiles brackets. Threaded inserts shall be factory installed to secure all door hinges, latches, and doorstops. Manufacturer's service and parts manual shall be provided to the building owner/manager upon request._________________ (insert one: toilet Partitions, dressing Compartments, Shower dividers, Urinal Screens) shall be ____________________ Series (insert series number) of Bobrick Washroom equipment, inc., Clifton Park, new York; Jackson, tennessee; Los Angeles, California; Bobrick Washroom equipment Company, Scarborough, ontario; Bobrick Washroom equipment Pty. Ltd., Australia; and Bobrick Washroom equipment Limited, United Kingdom.The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. 1090 Revised 8/08 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2008 by Bobrick Washroom Equipment, Inc.。

T9-I.T9-L1.T9-2LFrom...American Hakko Products, Inc.28920 N. Avenue Williams.Valencia, CA 91355 Tel: (661) 294-0090 Fax: (661) 294-0096 AHP14 Rev 2000-01For pricing information, please contact your local American Hakko representative or our customer service department at (661) 294-0090.American Hakko Products, Inc.P R O D U C T B U L L E T I NBulletin No: PB260Issue Date: November 5, 2007 Product:FM-203 Dual Port Soldering StationPart No:FM203-01 FM203-DPComments:The Hakko FM-203 is a Dual Port high performance soldering station. Even when soldering lead-free solders the high performance allows loweroperating temperatures. The soldering station can operate any of the following hand pieces, FM-2027 Soldering Iron, FM-2022 Parallel Remover (SMD tweezer), FM-2023 Mini Parallel Remover (SMD mini tweezer), FM-2024 Desoldering Module, and/or FM-2026 Nitrogen Soldering Iron. The soldering iron and desolder tool can be used in either or both ports and the tweezers are limited to one port with a soldering or desoldering iron in the other port.The station features a programmable sleep mode of 0-29 minutes or auto-power shut off at 30 minutes. Sleep mode, auto power shut off and tip temperature can be programmed separately for each port. The sleep mode reduces the tip temperature to approximately 200ºC (400ºF) after the programmed time (0-29 minutes). The lower tip temperature will reduce oxidation of the tip and improve the tip performance. When in sleep mode the tip will quickly return to temperature after the iron is removed from the holder.When utilizing the FM-2027 Soldering Iron the station uses the T15 series composite tip. The composite tip is a soldering tip in which a heating element and sensor are integrated with ceramic. Despite its highly compact design, the tip offers superior thermal response and greatly improved thermal recovery. T15 series tips are available in a wide variety of tip shapes and can also be used with the Hakko FM-203, FP-102 and FM-202 soldering stations. Any tip can be operated at temperatures 200 - 450ºC (400 - 840ºF). The station includes a card lock system to lock the preset soldering temperature. With the card removed operators can not adjust the working temperature.The FM-2022 uses T16 tips, The FM-2023 uses T9 tips, The FM-2024 uses N3 nozzles and The FM-2026 uses T17 tips.Documentation Provided By HMC ElectronicsFrom...American Hakko Products, Inc.28920 N. Avenue Williams.Valencia, CA 91355 Tel: (661) 294-0090 Fax: (661) 294-0096 AHP14 Rev 2000-01Specifications:FM-203 Soldering Station Power Consumption 140W 120VTemperature Range 200 - 450ºC (400 - 840ºF) Temperature Stability ±5ºC (±9ºF) Temperature Accuracy±15ºC (±27ºF)Soldering Iron (No.FM-2027) Power Consumption 70W (24V) Tip to Ground Resistance < 2Ω Tip to Ground Potential < 2mV Cord Length1.2m (47 in.) Total Length (w/o Cord)with 2.4D soldering tip attached 188mm (7.4 in.) Weight (w/o Cord)with 2.4D soldering tip attached30g (1.0 oz.)StationOutput 24V Dimensions 120(W) x 120(H) x 190(D)mm (4.7 x 4.7 x 7.5 in.) Weight (w/o cord)2.7kg (5.9 lb.) Contents:Part No.NameFM203-01 FM203-DPN/AFM-203 soldering station1 1 FM2027-02 Connector 12B2387 Power cord 1 1 B2972 Control card 1 1 B3219 Sleeve assembly, Green, anti-bacterial 1 1 B3216 Sleeve assembly, Yellow, anti-bacterial 0 1 B2300 Heat-resistant pad 1 2 FH200-01Iron Holder, Sleep, w/ 599B12B3253 Connecting cable 1 2 B2756 Tip tray1 1 N/A Instruction manual1 1The FM2023-DP includes two FM-2027 connectors and sleep holders. Tips not included.Documentation Provided By HMC ElectronicsFrom...American Hakko Products, Inc.28920 N. Avenue Williams.Valencia, CA 91355 Tel: (661) 294-0090 Fax: (661) 294-0096 AHP14 Rev 2000-01Accessories/Replacement Parts:Part No. NameSpecificationFM2027-01 HAKKO FM-2027 w/ Yellow Sleeve Assembly Does not include tip or holder B3216 Sleeve Assembly Yellow (Lock-type, Antibacterial) B3217 Sleeve Assembly Orange (Lock-type, Antibacterial) B3218 Sleeve Assembly Blue (Lock-type, Antibacterial) B3219Sleeve Assembly Green (Lock-type, Antibacterial)A1536 Cleaning sponge GreenFM2022-05 Conversion kit FM-2022 Parallel Remover with sleep holder and cable. Tips not included. FM2023-05 Conversion kit FM-2023 Mini Parallel Remover with sleep holder and cable. Tips included. FM2024-21 Conversion kit/120 V FM-2024 Desoldering Module with sleep holder and cable. Nozzle not included. FM2026-06 Conversion kit FM-2026 Nitrogen Iron with sleep holder and cable. Tips not included.FM2027-03Conversion kitFM-2027 Soldering Iron with sleep holder and cable. Tips not included.Tips and Nozzles:See PB258 for T15 tip list for HAKKO FM-2027Tips for HAKKO FM-2022Part No. Part Name SpecificationsT16-1001 Tip / CHIP 0.5I T16-1002 Tip / CHIP 0.5C T16-1003 Tip / CHIP 1L T16-1004 Tip / CHIP 2L T16-1005 Tip / SOP 6L T16-1006 Tip / SOP 8L T16-1007 Tip / SOP 10L T16-1008 Tip / SOP 13L T16-1009 Tip / SOP 16L T16-1010 Tip / SOP 20L T16-1011 Tip / SOP 25L T16-1012 Tip / SOP 18L T16-1013Tip / CHIP 3LDocumentation Provided By HMC ElectronicsFrom...American Hakko Products, Inc.28920 N. Avenue Williams.Valencia, CA 91355 Tel: (661) 294-0090 Fax: (661) 294-0096 AHP14 Rev 2000-01Tips for HAKKO FM-2023Part No. Part Name SpecificationsT9-I Tip / CHIP I T9-L1 Tip / CHIP 1L T9-L2Tip / CHIP 2LNozzles for HAKKO FM-2024Part No. Part NameSpecificationsN3-06 Nozzle / 0.6mm (0.02 in.) N3-08 Nozzle / 0.8mm (0.03 in.) N3-10 Nozzle / 1.0mm (0.04 in.) N3-13 Nozzle / 1.3mm (0.05 in.) N3-16 Nozzle / 1.6mm (0.06 in.) N3-20 Nozzle / 2.0mm (0.08 in.) N3-23 Nozzle / 2.3mm (0.10 in.)N3-L10 Long Nozzle / 1.0mm (0.04 in.)Tips for HAKKO FM-2026Part No. Part NameSpecificationsT17-B2 SHAPE-0.5B Conical T17-BC1 SHAPE-1BC Bevel T17-BC2 SHAPE-2BC Bevel T17-BC3 SHAPE-3BC BevelT17-BCF1 SHAPE-1BC Bevel Tinned on the soldering surface onlyT17-BCF2 SHAPE-2BC Bevel Tinned on the soldering surface onlyT17-BCF3 SHAPE-3BC BevelTinned on the soldering surface only T17-BL SHAPE-B Long Shape Conical T17-D08 SHAPE-0.8D Chisel T17-D16 SHAPE-1.6D Chisel T17-D24 SHAPE-2.4D Chisel T17-J02 SHAPE-0.2J Bent T17-KF SHAPE-KF Knife T17-KR SHAPE-KR Knife T17-KUSHAPE-KU KnifeAvailable:November 6, 2007Documentation Provided By HMC ElectronicsT9-I.T9-L1.T9-2L。

目录1. 金库网络门禁控制器 (3)1.1. DW-6831J/6832J/6834J-CP (3)2. 短信视频网络门禁控制器 (5)2.1. DW-6834D-CP (5)3. 网络双门互锁门禁控制器 (7)3.1. DW-6832AS-CP (7)4. 自助银行门禁控制器 (9)4.1. DW-6834Y-CP (9)5. 平安社区视频门禁控制器 (10)5.1. DW-6834C/6832C/6831C-CP (10)6. 网络门禁控制器 (11)6.1. DW-6831A/6832A/6834A-CP (11)7. 网络门禁控制器 (13)7.1. DW-6841A/6842A/6844A/6846A/6848A-CP (13)8. 网络门禁控制器 (15)8.1. DW-6814R-CP (15)9. 双门互锁控制器 (17)9.1. DW-2102AS-CP (17)10. 读卡器 (19)10.1. 读卡器-DW-100系列——DW-102M/102MK/108S/108C/108CK (19)10.2. 读卡器DW-106系列 (20)10.3. 读卡器DW-201系列 (21)10.4. 手机读卡器-------DW-202RM (22)10.5. 读卡器DW-203系列 (23)11. 发卡器 (24)11.1. 发卡器DW-100系列----DW-107 (24)12. 生物识别 (25)12.1. 半导体指纹仪——DW-FP1-L (25)12.2. TCP/IP半导体指纹仪——DW-FP3 (26)12.3. TCP/IP半导体指纹仪——DW-FP3-M (28)12.4. 光学指纹仪——DW-F11 (30)12.5. DW-F11-G (31)12.6. 人脸识别仪FC1 (32)12.7. 人脸指纹一体DW-FC1-PZ (34)12.8. 指纹静脉识别仪FV1 (35)12.9. 手持机 (37)12.10. 视频读卡一体机2240S (39)13. 丽安通停车场系统 (41)13.1. 停车场出入口管理控制器DW-C2104 (41)13.2. 停车场出入口管理控制器DW-C2115 (43)13.3. 道闸DW-C600 (44)13.4. 远距离读卡器206BT (45)13.5. 车牌识别C401T (46)13.6. 超声波车位引导C500系列 (48)14. 通道闸 (49)14.1. 三辊闸DW-TD1000GZ (49)14.2. 三辊闸DW-TD1001GZ (51)14.3. 翼闸DW-TD1000YZ (53)14.4. 翼闸DW-TD1001YZ (55)14.5. 摆闸DW-TD1000BZ (56)14.6. 摆闸DW-TD1001BZ (58)14.7. 全高转闸DW-TD1002QG (60)14.8. 全高转闸DW-TD1002QG (61)14.9. 平移门DW-TD1000PZ (63)15. 梯控系统 (65)15.1. IC卡电梯门禁控制器DW-TK2011M/TK2012/TK102M/TK102MK-CP (65)16. 消费机 (67)16.1. DW-3101M（台式） (67)16.2. DW-3101G (69)17. 巡更设备 (70)17.1. DW-XG300——蓝牙通讯座 (70)17.2. DW-XG5203——蓝牙巡更棒， (71)17.3. DW-XG100——巡更卡 (72)17.4. DW-XG5202/1——巡更棒 (73)18. 电锁 (74)18.1. 电锁——DW-601L/6280 (74)18.2. 灵性锁——LDS2 (75)18.3. 灵性锁——LX01 (76)1. 金库网络门禁控制器1.1. DW-6831J /6832J/ 6834J-CP针对银行标准设计的专用金库网络门禁控制器，远程与本地守库有机结合，防止内、外偷盗事件发生。

IBK 2513Large Interview Kit PackageCONDITIONS OF WARRANTY SERVICE• Free service for one year from the day of purchase if the problem is caused by manufacturing errors. • The components and maintenance service fee will be charged if the warranty period has expired.Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.) • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company. • Damage caused by natural disaster, abnormal voltage, and environmental factors etc.What’s included☐ 2 x IB500 LED Light☐ 1 x iLED 312 LED Light☐ 3 x Light Stands☐ 1 x IBG-500-3L Light Kit bagQuickStart Guide:☐IB500 LED Light QSG ☐ iLED 312 LED Light QSGCONDITIONS OF WARRANTY SERVICE• Free service for one year from the day of purchase if the problem is caused by manufacturing errors. • The components and maintenance service fee will be charged if the warranty period has expired.Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.) • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company. • Damage caused by natural disaster, abnormal voltage, and environmental factors etc.What’s included☐ IB 500 Light☐AC Adapter + Power Cord ☐ Remote ControlGETTING STARTED1. Connect the included AC Adapter to power the IB 500 light.2. Turn the light on / off with the Power Switch.3. Control the amount of the light with the Dimmer knob. Adjust the intensity of the light byturning the Dimmer Knob clock-wise to increase the intensity and counter clock-wise to reduce it.4. The IB 500 can also be powered by pro battery (optional accessories).SPECIFICATIONSOperating Volts: 12v - 14.4v Wattage: 30w Brightness: 2.55Klux/50c m Color T emperature: 5600K Dimension: 13.8” x 7.5” x 2.7” Weight (lbs): 5.8• Pro Battery OptionOptional Accessories• V17PBK-S Pro Battery Kit $149.00• V17PBK-A Pro Battery Kit $149.00• IB-L130A AB Mount Professional Battery $375.00• IB-L130S V Mount Professional Battery $375.00IB 500 LUX Drop OffIB 500 LUX Drop OffThe right amount of lightThe IB 500 lux drop off (Vertical)90The right amount of lightThe IB 500 lux drop off (Horizontal)90CONDITIONS OF WARRANTY SERVICE• Free service for one year from the day of purchase if the problem is caused by manufacturing errors. • The components and maintenance service fee will be charged if the warranty period has expired.Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.) • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company. • Damage caused by natural disaster, abnormal voltage, and environmental factors etc.What’s included☐ iLED 312 Light ☐ Soft Carrying Case ☐ AC Adapter ☐ SM201 Shoe Mount ☐ Sony “L” DV Battery ☐ Diffusion Filter ☐ DV Battery ChargerIndicatorNote : Due to the way the Sony L 500 Series and 300 series batteries are designed, Sony MP-F330/F570/F550 batteries will not work on the left battery slot of the iLED312.。

A4s Receiving CardDocument Version: V1. 2 .0Copyright © 2018 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi’an NovaStar Tech Co., Ltd.Trademarkis a registered trademark of Xi’an NovaStar Tech Co., Ltd.StatementYou are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). This document is intended to help you understand and use the product. For accuracy and reliability, NovaStar may make improvements and/or changes to this document at any time and without notice. Any problem in use or a n y good suggestion, please contact us through ways provided in the document. We will do our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible.Specifications Change HistoryChange HistorySpecifications Contents23Features (3)3.1 Improvement in Display Effect .....................................................................................................................33.2 Improvement in Maintainability (3)3.3 Improvement in HardwareReliability (4)3.4 Improvement in SoftwareReliability (5)4 Hardware (6)4.1 Appearance .................................................................................................................................................. 64.2Dimensions ............................................................................................................................................ (6)4.3 Indicators .......................................................................................................................................... (7)4.4 Definition of Data Interface( Top ) (8)4.1.1 24-Group ParallelData (8)4.1.2 64-Group SerialData ...............................................................................................................................114.1.3 Extended FunctionsDesign (14)5 Firmware Update (16)6 Applications (17)7 Specifications (18)A Abbreviation (19)B Terms (20)XI'AN NOVASTAR LTD. 1 Safety1 S afety This chapter illustrates safety of the A4s receiving card to ensure the product ’sstorage, transport, installation and use safety. Safety instructions are applicable to allpersonnel who contact or use the product. First of all, pay attention to following points.●Read through the instructions. ●Retain all instructions. ● Comply with all instructions.Storage and Transport Safety●Pay attention to dust and water prevention. ●Avoid long-term direct sunlight. ●Do not place the product at a position near fire and heat. ●Do not place the product in an area containing explosive materials. ●Do not place the product in a strong electromagnetic environment. ●Place the product at a stable position to prevent damage or personal injury caused by dropping. ● Save the packing box and materials which will come in handy if you ever have tostore and ship the product. For maximum protection during storage and shipping,repack the product as it was originally packed at the factory. Installation and Use Safety ●Only trained professionals may install the product. ●Plugging and unplugging operations are prohibited when the power is on. ●Ensure safe grounding of the product. ●Always wear a wrist band and insulating gloves. ● Do not place the product in an area having frequent or strong shake.XI'AN NOVASTAR TECHCO.,● Perform dust removing regularly.● Contact NovaStar for maintenance at any time, rather than have the productdisassembled and maintained by non-professionals without authorization.●Replace faulty parts only with the spare parts supplied by NovaStar.2 Overview 2 O verview A4s is a high-end receiving card developed by NovaStar, featuring small size andlarge loading capacity with a single card loading up to 256 x 256(PWM IC) pixels. A4s supports pixel level brightness and chroma calibration by working with NovaLCT and NovaCLB to realize calibration on each pixel. It can effectively remove colordifference and greatly improve LED display image consistency, presenting smootherimages to users. In addition, it also supports image rotation in 90° increments,creating richer images and improving visual experiences. Software and hardware designs of the A4s concern the user deployment as well asoperating and maintenance scenarios, enabling easier deployment, more stableoperating and more efficient maintenance. Advanced hardware design: ●The small-size hardware design is applicable to scenarios of small cabinet space and small pixel pitch. ●Use high-density connector which is resistant to dust and vibration and features high stability and high reliability. ● Assembly network transformer features simple design and improved magneticcompatibility, helping user ’s products to successfully pass the EMCauthentication.Useful software design: ●Support for LVDS transmission (Supported by dedicated firmware program). ● Support for smart module (Supported by dedicated firmware program).Specifications 3 Features● Support for 3D function.● Support for pre-stored image setting of the receiving card.● Support for module Flash management.● Supports monitoring voltage and temperature of itself without using otherperipherals.● Support for monitoring of Ethernet cable communication status (Supported bydedicated firmware program).● Support for 5-pin LCD module.●Support for image rotation in 90° increments.Specifications3.2Improvement inMaintainability3Features 3.1Improvement in Display Effect3.3Improvement in Hardware ReliabilityProduct images provided in this file are for reference only, and the actual productsshall prevail.Models of the high-density receptacle and plug used by A4s are shown in Table 4-1. Table 4-1 Model of high-density connector4.2 Dimensions4.3 Indicators4.4 Definition of Data Interface ( Top ) 4.4.1 24-Group Parallel Data4.4.2 64- G roup Serial Dataonly one interface from either the Recommended Smart Module Interface or the Recommended Module Flash Interface at the same time.5 Firmware Update6 Application sInput voltage DC 3.3 V –5.5 V Rated current0.5 ARated power consumption 2.5 W Operating temperature -20°C –70°C Storage temperature Operating humidity 10%RH –90%RHDimensions 70.0 mm × 45.0 mm × 7.3 mm Net weight 17.3 g● RoHS● EMC Class B- 25 °C – 125 °C 6ApplicationsA4s is applied to LED display synchronous system which is generally composed of the LED display, HUB board, receiving card, video controller and controller peripheral. The receiving card is connected to the display over a HUB board.Synchronous system requires connecting a computer to display the compute r ’ s images and texts on the LED screen. Structure of the synchronous system is as shown in the following figure.5Firmware UpdateStep 1 Visit www.novastar.tech to download the firmware update package and save it to PC.Step 2 Run NovaLCT and choose User > Advanced Synchronous System User Login tolog in. Step 3 Type the secret code " admin " to enter the program loading page.Step 4 Click Browse to select the program (the firmware update package you saved on PC)path and then click U pdate .Step 5 Click Refresh to check current hardware version information.Certification sfications 7SpecificationsA Abbre viationB TermsBT ermsCalibration coefficient Calibration system generates a group of values for each LED lamp, including information about brightness and chroma. After display calibration, the calibration values of each lamp are just the calibration coefficient. Smart module The smart module is composed of Flash and MCU.Flash could store calibration coefficients and lamp panel information. MCU could communicate with the receiving card to realize monitoring over temperature, voltage and wiring communication status, Working with the driver chip, A4s supports open circuit detection on LED.The smart module could make monitoring unit smaller, requiring no independent monitoring card and saving cabinet space.AAbbreviationE EMC Electro m a gnetic CompatibilityF FPGA Field - P rogrammable Gate ArrayL LED Light Emitting Diode MMCU Microcontroller Unit R RCFG Receiving Card Configuration。