色粉MSDS
- 格式:pdf
- 大小:176.76 KB
- 文档页数:2
1. 目的为有效控制工业化学品的运输、使用、处理等各个环节中的对人体和大自然的危害和预防工作。
2. 范围工业化学品,包括化学单质、化合物和混合物,不适用于民用受控消费品、以科学研究为目的的少量样品和国家另有规定的特殊危险化学品。
3. 操作说明3.1 化学品名称化学品中文名称:油墨3.2成分/组成信息树脂 40%色粉、助剂5%环已酮 10%异佛尔酮 15%乙二醇丁醚 15~30%3.3危险性概述危险性类别:侵入途径:吸入、食入、经皮肤吸收健康危害:会造成眼、皮肤、粘膜之刺激、皮肤干燥;神经中枢之麻醉,使人昏睡及晕眩。
环境影响:对水体有污染,对环境有危害。
燃爆危害:本品易燃烧. 在闪点或闪点以上温度时,泄漏的气体或液体很容易形成可燃烧爆炸危险。
3.4急救措施皮肤接触:立即脱去污染的衣着,用肥皂水和清水彻底冲洗皮肤。
眼睛接触:立即提起眼睑,用大量流动清水或生理盐水彻底冲洗至少15分钟。
就医。
吸入:迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难,给输氧。
如呼吸停止,立即进行人工呼吸。
就医。
立即进行人工呼吸。
就医。
食入:成人吞食30ML以上立即送医院。
3.5消防措施危险特性:易燃,其蒸气与空气可形成爆炸性混合物,遇明火、高热能引起燃烧爆炸。
与氧化剂接触发生化学反应或引起燃烧。
在火场中,受热的容器有爆炸危险。
其蒸气比空气重,能在较低处扩散到相当远的地方,遇火源会着火回燃。
3.6泄漏应急处理应急处理:迅速撤离泄漏污染区人员至安全区,并进行隔离,严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器,穿防静电工作服。
不要直接接触泄漏物。
尽可能切断泄漏源。
防止流入下水道、排洪沟等限制性空间。
小量泄漏:用砂土或其它不燃材料吸附或吸收。
大量泄漏:构筑围堤或挖坑收容。
用泡沫覆盖,降低蒸气灾害。
用防爆泵转移至槽车或专用收集器内,回收或运至废物处理场所处置。
3.7操作处置与储存操作注意事项:密闭操作,加强通风。
操作人员必须经过专门培训,严格遵守操作规程。
安全数据表MSDS粉末涂料1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22甘油酯(TGIC) R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
粉末涂料(塑粉)的MSDS1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22甘油酯(TGIC) R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
粉末涂料(塑粉)的MSDS1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22甘油酯(TGIC) R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
安全数据表MSDS粉末涂料1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22甘油酯(TGIC) R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
The information is provided as a service to our customers and is intended only for their use. The MSDS format adheres to standards and regulatory requirements according Annex II of EU Regulation (EC) No 1907/2006 (REACH) and its amendment by the COMMISSION REGULATION (EU) No 453/2010 from May 2010. It may not meet regulatory requirements in other locations.I. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND THE COMPANY• Grade Name: MXB-2900• Product Category: White Masterbatch• Chemical Formula: LLDPE, TiO2 (The product is a mixture under the definition of REACH/CLP) • Field of Application: Color Concentrates for plastic applications• Producer: ML Industries Co., Ltd.No.1 Industrial Zone, Jiuqu, Daojiao, Dongguan City, P.R. China• Emergency Phone No.: +86-769-88324778II. COMPOSITION AND INGREDIENTSIII. HAZARDS IDENTIFICATION• Indication of Danger: The product is not classified hazardous according to the Regulation (EC) No 1272/2008 and the Council Directives 67/548/EEC and 99/45/EEC.• Most Important Hazards: noneIV. FIRST AID MEASURES• Inhalation: No specific treatment is necessary since this material is not likely to be hazardous by inhalation. If dust or fumes reach excessive levels, they should be removed by fresh air. Get medical attention if cough or other symptoms develop.• Skin Contact: For hot product, immediately immerse in, or flush the affected area with large amounts of cold water. Cover with clean cotton sheeting or gauze and get prompt medical attention. Do not remove material from skin as the damaged flesh can be easily torn. Flush with large amounts of cool water. If irritation persists, contact a doctor.• Eye Contact: Flush eyes with plenty of water. If irritation persists, consult a doctor.• Ingestion: Not likely to be ingested in present form.V. FIRE-FIGHTING MEASURES• Suitable Extinguishing Media: Use dry chemical, foam., carbon dioxide or water spray• Extinguishing media, which must not be used for safety reasons: No information available• Special protective equipment for firefighters: In the case of irrespirable dust and/or fumes, use self-contained breathing apparatus and dust impervious protective suit.VI. ACCIDENTAL RELEASE MEASURES• Personal Precautions: No information available• Environmental Precautions: Do not contaminate water• Methods for cleaning up: Sweep up and shovel into suitable containers for disposalVII. HANDLING AND STORAGE:• Handling: Use with adequate ventilation. Minimize generation of dust.• Storage: Store at normal temperature and keep dry.VIII. EXPOSURE CONTROLS/PERSONAL PROTECTION• Engineering measures to reduce exposure: If process generates dust, fumes or mist, use ventilation to keep exposure to airborne below the exposure limit• Exposure limit(s): not determined• Occupational exposure controls: not determined• Personal Protective Equipment: not determined• Respiratory Protection: If dust, smoke or fumes are generated during processing or handling, wear appropriate approved respiratory protection to keep concentration below the permissible exposure limit. • Hand protection: Wear suitable gloves to protect against specific hazard• Eye protection: Wear eye/face protection appropriate for the specific hazard• Skin and body protection: Wear suitable gloves to protect against specific hazard.• Work/Hygiene Practices: Do not breathe fumes/mist Avoid contact with skin.• Environmental exposure controls: Do not flush into surface water or sanitary sewer systemIX. PHYSICAL AND CHEMICAL PROPERTIESGeneral information• Physical state: solid• Odor: no odor• Color: white• Specific gravity: 23°C 1.90g/cm3Important Health Safety and Environmental information• PH: Not applicable• Boiling point/range: Not applicable• Flammability (solid, gas): No information available• Explosive properties: No information available• Oxidizing properties: No information available• Vapor pressure: No information available• Solubility: Insoluble• Partition coefficient (n-octanol/water): Not applicable• Viscosity: Not applicable• Vapor density: No information available• Evaporation rate: No information availableX. STABILITY AND REACTIVITY• Stability: Stable under recommended storage conditions• Conditions to avoid: Do not store near heat, flame or strong oxidants. Minimize dust generation and accumulation• Materials to avoid: No information available• Hazardous decomposition products: Oxides of carbon• Polymerization: UnknownXI. TOXICOLOGICAL INFORMATIONLocal effects• Skin irritation: No data available• Eye irritation: No data available• Inhalation: Health injuries are not know or expected under normal use• Ingestion: Health injuries are not know or expected under normal use• Sensitization: No information available• Acute toxicity: No information available• Chronic toxicity: No information availableSpecific effects• Carcinogenic effects:Chronic exposure to dust can cause lung diseases including cancer. When encapsulated in a plastic matrix, risk of exposure is decreased. Protect workers from dust exposures during handling or grinding operation.• Mutagenic effects: Not considered to be mutagenic• Reproductive toxicity: Not believe to be a reproductive hazard• Target organ effects: Skin Eyes Respiratory tractXII. ECOLOGICAL INFORMATION• Ecological effects: N/A• Product information: N/A• Aquatic toxicity: N/A• Other information: N/A• Additional ecological information: N/AXIII. DISPOSAL CONSIDERATIONS• Waste form residues / unused products: Dispose in accordance with local regulations• Further information:Waste codes should be assigned by based on the application for which the product was usedXIV. TRANSPORT INFORMATION• UN/ld No: No information available• ADR/RID: Not regulated for transport• IMDG /IMO: Not regulated for transport• ICAO/IATA: Not regulated for transportXV. REGULATORY INFORMATION• In accordance with local and national regulations• Indication of danger: Not dangerous goodsXVI. OTHER INFORMATION•Changes against last version: Adaption to directive 453/2010/EC• This information is based upon technical information believed to be reliable.。
粉末涂料(塑粉)的MSDS1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R—术语(*)异氰尿酸三缩水0。
1至〈5。
0% T R46 R23/25 R48/22甘油酯(TGIC)R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止.如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助.眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗.切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风.无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理.切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门.7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
粉末涂料(塑粉)的MSDS1 产品产品名称热固性粉末涂料应用静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22甘油酯(TGIC) R41 R43(*)详见16小节3.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
1.产品产品名称:热固性粉末涂料应用:静电喷涂2.成分构成/信息在1997化学品(危险品知识与包装)规章的范围内体现健康危害的物质:名称含量范围代表符号R-术语(*)异氰尿酸三缩水0.1至<5.0% T R46 R23/25 R48/22 甘油酯(TGIC) R41 R433.危害识别该产品因含有TGIC被定为具有毒性。
可能会有损害遗传基因的风险。
可能引起皮肤接触性过敏。
吸入和误食均有伤害。
4.急救措施一般:若有任何疑问或有症状持续出现,请寻医助。
保证失去意识的患者口中无任何东西。
吸入:移到通风处,保持患者体温和静止。
如果患者呼吸不规律或停止,进行人工呼吸急救。
保证口中无异物。
如果失去意识,安置在恰当位置并寻医助。
眼睛接触:取下隐形眼睛。
用大量干净的清水冲洗至少十分钟,保证眼皮张开并寻医助。
皮肤接触:脱下被污染的衣物。
用肥皂和水或者是合适的皮肤清洁剂彻底清洗。
切忌使用溶剂或稀释剂。
吞服:如不慎吞食,立即寻求医助。
保持患者静躺,切勿导吐。
5.消防措施灭火媒介:建议:水,泡末,干粉,CO2,水喷淋或水雾禁止使用:高压惰性气体(如CO2),水枪喷射建议:火灾现场浓厚的黑烟包含很多由于燃烧产生的有害物质(参看第10小节)。
暴露于这种分解的物质中对健康有害。
需要自带呼吸器的器械。
用水喷的方式冷却暴露在火中的密闭容器。
切勿把灭火器的流出物直接排到下水道或河道中。
6.应急意外泄露排除火源,保证场地通风。
无关人员远离现场。
避免吸入灰尘。
涉及到的保护措施列在7、8小节。
打扫溢出粉末应使用防静电的真空清洁器或湿的清洁刷,并根据废物处理规则(参看13小节)收集在密闭容器中待处理。
切勿使用扫把,以免形成灰尘层和静电积累。
请勿直接排放到下水道或河道中。
如果产品进入下水道或河道,应立即联系当地自来水公司;如果污染了河流、小溪或湖泊,应求助当地环保部门。
7.处置和存储处置采取措施以预防灰尘积聚到高于爆炸或偶然爆炸极限。
29 29 29 bluePost Code:712021Tel:(+86 29)Page 1 of 3M A TERIAL SAFETY D A T A SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct:phosphor and regeneration of blue phosphorChemical Type: Silver activated zinc sulfide phosphor First Issue Date: Mar. 11, 2008 Revised Date:Mar. 11, 2008Manufacturer's Name: Phosphor Material Co.Ltd.Address: i P.R.ChinaDivision: Quality Assurance Department Phone: +86 Fax:+86 Emergency Phone:+862. COMPOSITION / INFORMATION ON INGREDIENTSIngredients: Silver activated zinc sulfide phosphorChemical composition and Contents: ZnS :Ag+Co 2O 3ZnS :Ag ≧ 98%, Co 2O 3 ≦ 2%CAS No : ZnS :1314-98-3;Ag :7429-90-5; Co 2O 3:1307-96-63. HAZARDS IDENTIFICATIONEmergency Overview: Nothing worthy of special mentionHealth Effects:Inhalation of dust may result in respiratory organs damage. Environmental Effects: Not Available Physicochemical Effects:Nonflammable4. FIRST AID MEASURESInhalation: Remove from exposure, provide fresh air and call for medical aid. Skin Contact: W ash with plenty of clear water immediately . Eye Contact:W ash with plenty of clear water immediately .Post Code:712021 Shaanxi IRICO Phosphor Material Co.Ltd.Tel:(+86 29) 3333 3482Fax:(+86 29 )3333 1625E-mail:y g c lg s@Page 2 of 3When irritation remains, call for medical aid.Ingestion: Call for medical aid.Protection to First-aiders: If there is much dust, wear goggles, dustproof musk and gloves.5. FIRE FIGHTING MEASURESFlammable Properties: NonflammableExtinguishing Media: Use extinguishing media suitable for the surrounding fire.6. ACCIDENT AL RELEASE MEASURESLand Spill: Clean up spills using methods with which avoid dust generation such as vacuuming or wet dustmopping. If airborne dust is generated, use an appropriate respirator.W ater Spill: Do never drain in a regular waterway.This material settles in still water. Recover precipitates in containers.7. HANDLING AND STORAGEHandling: 1. Use appropriate protective gears and equipments to prevent inhalation and contact with eyes and skin.2. W ash hands and gargle after handling.3. Do not eat nor smoke in a handling area.Storage: 1. Do not expose containers to direct sunlight. Store indoors and in a dry place.2. Keep containers covered with lids.Containers: 1. Do not damage containers.2. W atch weight and check out handles are fine before handling. Containers are sometimes heavy (20kgs).3. When using empty containers for any purpose, remove material and wash them completely.4. Do not use polyethylene inner bags for another purpose.8. EXPOSURE CONTROLS / PERSONAL PROTECTIONExposure Limit V alues: Not EstablishedOccupational Exposure ControlsEngineering Controls: Use in sealed equipment or use ventilation to avoid airborne dust.Personal Protection: Use dustproof mask, goggles and gloves.Environmental Exposure Controls: Do not dump this product into waterway or on the ground.9. PHYSICAL A ND CHEMICAL PROPERTIESAppearance: Blue PowderMelting Point: Not AvailableDecomposition point: Not AvailableSpecific gravity: 4.1g/cm3Solubility:W ater:InsolubleAcid:Slightly Soluble10. ST ABILITY AND REACTIVITYStability: StableMaterials to Avoid: Not A vailablePost Code:712021 Shaanxi IRICO Phosphor Material Co.Ltd.Tel:(+86 29) 3333 3482Fax:(+86 29 )3333 1625E-mail:y g c lg s@Page 3 of 3 Hazardous Reactions / Decomposition Products: Not Available11. TOXICOLOGICAL INFORMA TIONAcute Toxicity: Not A vailableEye Irritation: Powder of this product may irritate eyes.Skin Irritation: Not A vailable12. ECOLOGICAL INFORMATIONPersistence and Degradability: Not A vailableBioaccumulative Potential: Not A vailable13. DISPOSAL CONSIDERATIONSDispose in accordance with appropriate government regulations.Do not dump this product into sewers, on the ground or into any body of water.14. TRANSPORT INFORMA TIONUN No.: Not A pplicableProper Shipping Name: Not A pplicableClass:Not A pplicableSea Transport(IMDG):Not A pplicableAir Transport(TCAO/IA T A):Not A pplicableMake sure that containers have no leakage.Load and tie firmly to avoid falling, damage during transportation.Be accordance with appropriate regulations.15. REGULA TORY INFORMATIONTreat in accordance with appropriate government regulations.IMDG Code and TCAO/IA T A C lass are not applicable.16. OTHER INFORMA TIONShaanxi IRICO Phosphor Material Co.Ltd. has attempted to provide current and accurate information herein.Shaanxi IRICO Phosphor Material Co.Ltd. makes NO representations regarding the accuracy or completenessof the information and assumes NO liability for any loss, damage, injury of any kind which may result from or ariseout of the use of or reliance on this information by any person.END OF MA TERIAL SAFETY DA T A S HEET。
蓝色荧光粉MSDS29 29 29 bluePost Code:712021Tel:(+86 29)Page 1 of 3M A TERIAL SAFETY D A T A SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct:phosphor and regeneration of blue phosphorChemical Type: Silver activated zinc sulfide phosphor First Issue Date: Mar. 11, 2008 Revised Date:Mar. 11, 2008Manufacturer's Name: Phosphor Material Co.Ltd.Address: i P.R.ChinaDivision: Quality Assurance Department Phone: +86 Fax:+86 Emergency Phone:+862. COMPOSITION / INFORMATION ON INGREDIENTSIngredients: Silver activated zinc sulfide phosphorChemical composition and Contents: ZnS :Ag+Co 2O 3ZnS :Ag ≧ 98%, Co 2O 3 ≦ 2%CAS No : ZnS :1314-98-3;Ag :7429-90-5; Co 2O 3:1307-96-63. HAZARDS IDENTIFICATIONEmergency Overview: Nothing worthy of special mentionHealth Effects:Inhalation of dust may result in respiratory organs damage. Environmental Effects: Not Available Physicochemical Effects: Nonflammable4. FIRST AID MEASURESInhalation: Remove from exposure, provide fresh air and call for medical aid. Skin Contact: W ash with plenty of clear water immediately . Eye Contact:W ash with plenty of clear water immediately .Post Code:712021 Shaanxi IRICO Phosphor Material Co.Ltd.Tel:(+86 29) 3333 3482Fax:(+86 29 )3333 1625E-mail:**************Page 2 of 3When irritation remains, call for medical aid.Ingestion: Call for medical aid.Protection to First-aiders: If there is much dust, wear goggles, dustproof musk and gloves.5. FIRE FIGHTING MEASURESFlammable Properties: NonflammableExtinguishing Media: Use extinguishing media suitable for the surrounding fire.6. ACCIDENT AL RELEASE MEASURESLand Spill: Clean up spills using methods with which avoid dust generation such as vacuuming or wet dustmopping. If airborne dust is generated, use an appropriate respirator.W ater Spill: Do never drain in a regular waterway.This material settles in still water. Recover precipitates in containers.7. HANDLING AND STORAGEHandling: 1. Use appropriate protective gears and equipments to prevent inhalation and contact with eyes and skin.2. W ash hands and gargle after handling.3. Do not eat nor smoke in a handling area.Storage: 1. Do not expose containers to direct sunlight. Store indoors and in a dry place.2. Keep containers covered with lids.Containers: 1. Do not damage containers.2. W atch weight and check out handles are fine before handling. Containers are sometimes heavy (20kgs).3. When using empty containers for any purpose, remove material and wash them completely.4. Do not use polyethylene inner bags for another purpose.8. EXPOSURE CONTROLS / PERSONAL PROTECTIONExposure Limit V alues: Not EstablishedOccupational Exposure ControlsEngineering Controls: Use in sealed equipment or use ventilation to avoid airborne dust.Personal Protection: Use dustproof mask, goggles and gloves.Environmental Exposure Controls: Do not dump this product into waterway or on the ground.9. PHYSICAL A ND CHEMICAL PROPERTIESAppearance: Blue PowderMelting Point: Not AvailableDecomposition point: Not AvailableSpecific gravity: 4.1g/cm3Solubility:W ater:InsolubleAcid:Slightly Soluble10. ST ABILITY AND REACTIVITYStability: StableMaterials to Avoid: Not A vailablePost Code:712021 Shaanxi IRICO Phosphor Material Co.Ltd.Tel:(+86 29) 3333 3482Fax:(+86 29 )3333 1625E-mail:**************Page 3 of 3 Hazardous Reactions / Decomposition Products: Not Available11. TOXICOLOGICAL INFORMA TIONAcute T oxicity: Not A vailableEye Irritation: Powder of this product may irritate eyes.Skin Irritation: Not A vailable12. ECOLOGICAL INFORMATIONPersistence and Degradability: Not A vailableBioaccumulative Potential: Not A vailable13. DISPOSAL CONSIDERATIONSDispose in accordance with appropriate government regulations.Do not dump this product into sewers, on the ground or into any body of water.14. TRANSPORT INFORMA TIONUN No.: Not A pplicableProper Shipping Name: Not A pplicableClass:Not A pplicableSea Transport(IMDG):Not A pplicableAir Transport(TCAO/IA T A):Not A pplicableMake sure that containers have no leakage.Load and tie firmly to avoid falling, damage during transportation.Be accordance with appropriate regulations.15. REGULA TORY INFORMATIONTreat in accordance with appropriate government regulations.IMDG Code and TCAO/IA T A C lass are not applicable.16. OTHER INFORMA TIONShaanxi IRICO Phosphor Material Co.Ltd. has attempted to provide current and accurate information herein.Shaanxi IRICO Phosphor Material Co.Ltd. makes NO representations regarding the accuracy or completeness of the information and assumes NO liability for any loss, damage, injury of any kind which may result from or arise out of the use of or reliance on this information by any person.END OF MA TERIAL SAFETY DA T A S HEET。
**** MATERIAL SAFETY DATA SHEET ****快件声明物安全特性报告MSDS Name (报告物名称) CRT green phosphor and regeneration of green phosphor (CRT用绿色荧光粉)Air Way Bill (运单号)**** SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION ****第一部分化工产品及发件单位MSDS Name(报告物名称): green phosphor and regeneration of greenphosphor(绿色荧光粉)Catalog Numbers(化工品分类号): Copper and aluminum activated zinc sulfide phosphorSynonyms(又名):Company Identification(发件公司名称):For information, call(一般联系电话): +86-755For emergencies, call(应急联系电话): +86-755**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****成份特点Hazard Symbols(危险特性): Nothing worthy of special mention 无明显危险特性Risk Phrases(危险条件): Inhalation of dust may result in respiratory organs damage.吸入粉末可能损害呼吸器官**** SECTION 3 - HAZARDS IDENTIFICATION ****危险特征EMERGENCY OVERVIEW 概述Eye眼睛: Wash with plenty of clear water immediately. 立即用水冲洗Skin皮肤: Wash with plenty of clear water immediately. 立即用水冲洗Ingestion误食: Call for medical aid. 及时就医Inhalation吸入: Remove from exposure, provide fresh air and call for medical aid. 呼吸新鲜空气并就医Chronic可否引起慢性疾病: Not Established 未知**** SECTION 4 - FIRST AID MEASURES ****应急医疗救治Eyes眼睛: Wash with plenty of clear water immediately. 立即用水冲Skin皮肤: Wash with plenty of clear water immediately. 立即用水冲洗Ingestion误食: Call for medical aid. 及时就医Inhalation吸入: Remove from exposure, provide fresh air and call for medical aid. 呼吸新鲜空气并就医Notes to Physician给内科医生的建议:**** SECTION 5 - FIRE FIGHTING MEASURES ****消防扑救方法Flammable Properties: Nonflammable 不可燃Extinguishing Media: Use extinguishing media suitable for the surrounding fire. 适当方法扑救包装火焰**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****事故处理General Information:一般信息:Spills/Leaks泄露/溢出: Clean up spills using methods with which avoid dust generation such as vacuuming or wet dust mopping. If airborne dust is generated, use an appropriate respirator..用真空吸尘或湿拖把清扫。