六角头螺栓 全螺纹 B级国标与德标尺寸对比

GB—中国国家标准（国标）ANSI—美国国家标准（美标）DIN—德国国家标准（德标）ASME—美国机械工程师协会标准JIS—日本国家标准（日标）BSW—英国国家标准内六角螺钉GB70与德标DIN912相一致。

4.8级六角螺栓标准：德标（全牙DIN558）德标（半牙DIN601）老国标（全牙、半牙GB30）ISO尺度（全牙ISO4018）ISO标准（半牙ISO4016）8.8级六角螺栓标准：德标（全牙DIN933）德标（半牙DIN931）老国标（全牙、半牙GB30）ISO标准（全牙ISO4017）ISO标准（半牙ISO4014）以上尺度的螺栓从外形尺寸上有如下区分，重要是指头部对边尺寸：1、4.8与8.8在同一尺度中尺寸雷同；2、4.8、8.8老国标GB30M8的规格对边为14mm,其他都是13mm；3、另外DIN、GB30标准中M10、M12、M14、M22的尺寸雷同与ISO标准不同，其余规格全体与ISO标准一致。

4、新国标4.8级GB5780半牙、5781全牙,螺钉;8.8级GB5782半牙、GB5783全牙分辨对应与ISO4016、ISO4018、ISO4014、ISO4017尺寸一致,非标紧固件。

六角螺母老国标GB52除M8规格以外,螺母，其余全体与德标DIN934一致；六角螺母新国标GB6170、GB6171与ISO4032相一致,螺丝，GB6172、GB6173与ISO4035相一致；新标与老标的区别在于：M8、M10、M12、M14、M22系列的产品，在对边宽度上有所区别。

除M22系列的新产品外，新标产品M8、M10、M12、M14的头部对边比老标的对边要小1MM。

分别为13、16、18、21MM ，而M22系列的新产品，新标比老标的对边反而要大2MM，应特别注意。

对于头部厚度，新标和老标之间略有差别，在要求不是非常严格的情况下可以通用。

新标与德标的区别在于：M10、M12、M14、M22的产品规格，在对边宽度上有所差别。

德标和国标紧固件对照表21DIN18182 干壁钉（墙板钉）dry wall screws21 1 DIN28129 环型螺母lifting nuts(eyenuts)GB63-8821 2 DIN70952圆螺母用止退垫圈tab washers forslotted roundnutsGB858-88从群体上看，中专毕业生的劣势是阅历较少、知识层次相对不高;优势是学校专业设置大多贴近市场实际、贴近一线需要，且中专毕业生年青、肯吃苦、可塑性强。

从个体来说，每位毕业生的优势与长项又各不相同，如有相当一部分毕业生动手操作能力较好;有些学生非常上进，上学期间还同时参加了职业资格考试或自学考试。

所以，在实事求是，不弄虚作假的前提下，要特别注意扬长避短，从而在竞争中取得优势，打动聘任者。

没有重点和章法的写作易使文章显得头绪不清、条理紊乱。

非常热爱市场销售工作，有着十分饱满的创业激情。

在××××两年从事现磨现煮的咖啡市场销售工作中积累了大量的实践经验和客户资源。

与省内主要的二百多家咖啡店铺经销商建立了十分密切的联系，并在行业中拥有广泛的业务关系。

在去年某省的咖啡博览会上为公司首次签定了海外的定单。

能团结自己的同事一起取得优异的销售业绩。

合理分配自我介绍的时间前文说过，自我介绍一般也就持续1—3分钟，所以应聘者得合理分配时间。

常规安排是：第一段用于表述个人基本情况，中段重点谈自己的工作经历或社会实践经验，最后展望下自己的职位理想。

但如果自我介绍被要求在1分钟完成，应聘者就要有所侧重，突出最有料的一点。

在实践中，有些应聘者试图在短短的时间内吐露自己的全部经历，而有些应聘者则是三言两语就完成了自我介绍，这些都是不明智的做法。

突出和应聘职位相关的信息自我介绍的内容不宜太多的停留在诸如姓名、教育经历等部分上，因为面试官可以在应聘者的简历上一目了然地看到这些内容。

应聘者应该在自我介绍时选择一至两项跟自己所应聘的职位相关的经历和成绩作简述，以证明自己确实有能力胜任所应聘的工作职位。

螺栓螺母德标、欧标、国标对照表—— DIN EN ISO GB对照表之青柳念文创作新德标旧德标英文名中文名国标DIN EN ISO4014DIN 931-1Hexagon head bolts - Product grades Aand B(ISO 4014:1999)六角头螺栓GB/T 5782-2000DIN EN ISO4016DIN 601Hexagon head bolts - Product gradeC(ISO 4016:1999)六角头螺栓 C级GB/T 5780-2000DIN EN ISO4017DIN 933Hexagon head screws - Product grade Aand B (ISO 4017:1999)六角头螺栓全罗纹GB/T 5783-2000DIN EN ISO4018DIN 558Hexagon head screws - Product grade C(ISO 4018:1999)六角头螺栓全罗纹 C级GB/T 5781-2000DIN EN ISO8676DIN 961Hexagon head screws with metric finepitch thread - Product grade A and B(ISO8676:1999)六角头螺栓细牙全罗纹GB/T 5786-2000DIN EN ISO8765DIN 960Hexagon head bolts with fine pitchthread - Product grades A and B(ISO8765:1999)六角头螺栓细牙GB/T 5785-2000DIN EN ISO4032DIN 934Hexagon nuts,style 1-Product grades Aand B(ISO: 4032:1999)1型六角螺母GB/T 6170-2000DIN EN ISO4033Hexagon nuts,style 2-Product grades Aand B(ISO: 4033:1999)2型六角螺母GB/T 6175-2000DIN EN ISO4034DIN 555Hexagon nuts - Product grade C (ISO4034:1999)六角螺母 C级GB/T 41-2000DIN EN ISO4035DIN 439-2Hexagon thin nuts(chamfered)-Productgrade A and B (ISO 4035:1999)六角薄螺母DINEN ISO 4036DIN 439-1Hexagon thin nuts - Product gradeB(unchamfered)(ISO 4036:1999)六角薄螺母无倒角GB/T 6174-2000DIN EN ISO8673DIN 934|DIN 971-1Hexagon nuts,style 1,with metric finepitch thread - Product grades A and B(ISO 8673:1999)1型六角螺母细牙GB/T 6171-2000DIN EN ISO8674DIN 971-2Hexagon nuts,style 2,with metric finepitch thread - Product grades A and B(ISO 8674:1999)2型六角螺母细牙GB/T 6176-2000DIN EN ISO8675DIN 439-2Hexagon thin nuts with metric fine pitchthread - Product grades A and B (ISO8675:1999)六角薄螺母细牙GB/T 6173-2000DIN EN ISO4762DIN 912Hexagon socket head cap screws(ISO4762:1997)内六角圆柱头螺钉DIN EN ISO7380Hexagon socket button head sxrews (ISO7380:1997)内六角平圆头螺钉DIN EN ISO 10642DIN 7991H exagon socket countersunk headscrews (ISO 10642:1997)内六角沉头螺钉DIN EN ISO1207DIN 84Slotted cheese head screws-Productgrade A(ISO 1207:1992)开槽圆柱头螺钉GB/T 65-2000DIN EN ISO1580DIN 85Slotted pan head screws-Product gradeA(ISO 1580:1994)开槽盘头螺钉GB/T 67-2000DIN EN ISO2009DIN 963Slotted countersunk flat headscrews(common head style)(ISO2009:1994)开槽沉头螺钉GB/T 68-2000DIN EN ISO2010DIN 964Countersunk slotted raised headscrews(common head style)-Producegrade A(ISO 2010:1994)开槽半沉头螺钉GB/T 69-2000DIN EN ISO7045DIN 7985P an head screws with type H or type Zcross recess-Product grade A(ISO7054:1994)十字槽盘头螺钉GB/T 818-2000DIN EN ISO 7046-1DIN 965Countersunk flat head screws (common head style)with type H or type Z crossrecess,product grade A-Part 1:Steel ofproperty class 4.8(ISO 7046-1:1994)DIN EN ISO 7046-2DIN 965Cross recessed countersunk flat headscrews (common head style),productgrade A-Part2:Steel of property class8.8,stainless steel and nonferousmetals(ISO 7046-2:1990)十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3DIN EN ISO7047DIN 966Countersunk raised head screws(common head style) with type H ortype Z cross recess-Product grade A(ISO7047:1994)十字槽半沉头螺钉GB/T 820-2000DIN EN ISO7048Cross recessed cheese head screws (ISO7048:1998)十字槽圆柱头螺钉GB/T 822-2000DIN EN ISO 10644Screw and washer assemblies with plainwashers-Washer hardness classes200HV and 300HV(ISO 10644:1998)螺栓或螺钉和平垫圈组合件DIN EN ISO 10510Tapping screw and washer assemblieswith plain washers(ISO 10510l:1999)自攻螺钉和平垫圈组合件IDN EN ISO 15480Hexagon washer head drilling screwswith tapping screws thread (ISO15480:1999)六角凸缘自钻自攻螺钉IDN EN ISO 15481Cross recessed pan head drilling screwswith tapping screw thread(ISO15481:1999)十字槽盘头自钻自攻螺钉IDN EN ISO 15482Cross recessed countersunk head drillingscrews with tapping screw thread (ISO15482:1999)十字槽沉头自钻自攻螺钉IDN EN ISO 15483Cross recessed raised countersunk headdrilling screws with tapping screwthread(ISO 15483:1999)十字槽半沉头自钻自攻螺钉DIN EN ISO 10669Plain washers for tapping screw andwasher assemblies - Normal and largeseries - Product grade A （ISO平垫圈用于自攻螺钉和垫圈组合件10669:1999)DIN EN ISO 10673Plain washers for screw and washerassemblies - Small,normal and largeseries - Product grade A (ISO10673:1998)平垫圈用于螺钉和垫圈组合件DIN EN ISO2338DIN 7Parallel pins,of unhardened steel andaustenitic stainless steel(ISO 2338:1997)圆柱销不淬硬钢和奥氏体不锈钢DIN EN ISO8733DIN 7979P arallel pins whit internal thread,ofunhardened steel and austeniticstainless steel(ISO 8733:1997)内罗纹圆柱销不淬硬钢和奥氏体不锈钢DIN EN ISO8734DIN 6325P arallel pins,of hardened steel ormartensitic stainless steel(Dowelpins)(ISO 8734:1997)圆柱销淬硬钢和马氏体不锈钢DIN EN ISO8735DIN 7979P arallel pins with internal thread,ofhardened steel and martensitic stainlesssteel(ISO 8735:1997)内罗纹圆柱销淬硬钢和马氏体不锈钢DIN EN ISO8748DIN 7344S pring-type straight pins,coiled,heavyduty (ISO 8748:1997)弹性圆柱销卷制重型DIN EN ISO8750DIN 7343S pring-type straight pins,coiled,standardduty (ISO 8750:1997)弹性圆柱销卷制尺度型DIN EN ISO8751Spring-type straight pins,coiled,lightduty （ISO 8751:1997)弹性圆柱销卷制轻型DIN EN ISO8752DIN 1481S pring-type straight pins,slotted,heavyduty (ISO 8752:1997)弹性圆柱销直槽重型DIN EN ISO 13337DIN 7346S pring-type straight pins,slotted,lightduty (ISO 13337:1997)弹性圆柱销直槽轻型DIN EN ISO1234DIN 94Split pins （ISO1234:1997)启齿销GB/T 91-2000DIN EN ISO7089Plain washers-Normal series-Productgrade A平垫圈 A级DIN EN ISO7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000)平垫圈倒角型 A级DIN EN ISO7091Plain washers-Normal series-Productgrade C(ISO 7091:2000)平垫圈 C级GB/T 95-2002DIN EN ISO7092Plain washers-Small series-Productgrade A(ISO 7092:2000)小垫圈 A级GB/T 848-2002DIN EN ISO 7093-1Plain washers-Large series-Part 1:Product grade A(ISO 70931-1:2000)大垫圈 A级DIN EN ISO 7093-2Plain washers-Normal series-Part 3:Product grade C(ISO 70936-2:2000)大垫圈 C级DIN EN ISO7094Plain washers-Extra large series -Productgrade C(ISO 7094:2000)特大垫圈 C级GB/T 5287-2002DIN EN ISO7040DIN 982|DIN 6924Prevailing torque type hexagon nuts(with non-metallic insert),style 1 -1型非金属嵌件六角锁紧Property classes 5,8 and 10(ISO7040:1997)螺母DIN EN ISO7042DIN 980|DIN 6925Prevailing torque type all-metal hexagonnuts,style 2 - Property classes 5,8, 10and 12(ISO 7042:1997)2型全金属六角锁紧螺母DIN EN ISO7719Prevailing torque type all-metal hexagonnuts,style 1- Property classes 5,8 and10(ISO 7719:1997)1型全金属六角锁紧螺母GB/T 6184-2000DIN EN ISO 10511DIN 985Prevailing torque type hexagon thin nuts(with non-metallic insert )(ISO10511:1997)非金属嵌件六角锁紧薄螺母DIN EN ISO 10512DIN 982|DIN 6924Prevailing torque type hexagon nuts(with non-metallic insert),style 1,withmetric fine pitch thread-Property classes6,8 and 10(ISO 10512:1997)1型非金属嵌件六角锁紧螺母细牙DIN EN ISO 10513DIN 980|DIN 6925Prevailing torque type all-metal hexagonnuts,style 2,with metric fine pitchthread - Property classes 8,10 and12(ISO 10513:1997)2型全金属六角锁紧螺母细牙。

紧固件规格标准——GB标准档圈锥销锁紧档圈 GB 883-86螺钉锁紧档圈 GB 884-86带锁圈的螺钉锁紧档圈 GB 885-86 轴肩档圈 GB 886-86螺钉紧固轴端档圈 GB 891-86螺栓紧固轴端档圈 GB 892-86孔用弹性档圈-A型 GB 893.1-86 孔用弹性档圈-B型 GB 893.2-86 轴用弹性档圈-A型 GB 894.1-86 轴用弹性档圈-B型 GB 894.2-86 孔用钢丝档圈 GB 895.1-86轴用钢丝档圈 GB 895.2-86开口档圈 GB 896-86钢丝锁圈 GB 921-86夹紧档圈 GB 960-86自攻螺钉十字槽盘头自攻螺钉 GB 845-85 十字槽沉头自攻螺钉 GB 846-85 十字槽半沉头自攻螺钉 GB 847-85 开槽盘头自攻螺钉 GB 5282-85开槽沉头自攻螺钉 GB 5283-85开槽半沉头自攻螺钉 GB 5284-85 塑料滚花头螺钉 GB 840-88开槽球面圆柱头轴位螺钉 GB 946-88开槽球面大圆柱头螺钉 GB 947-88开槽沉头不脱出螺钉 GB 948-88开槽半沉头不脱出螺钉 GB 949-88内六角花形盘头螺钉 GB 2672-86内六角花形沉头螺钉 GB 2673-86内六角花形半沉头螺钉 GB 2674-86内六角圆柱头轴肩螺钉 GB 5281-85内六角花形圆柱头螺钉-4.8级 GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级 GB 6191-86 精密机械用紧固件十字槽螺钉 GB /T 13806.1-92 十字槽半沉头螺钉 GB /T 820-2000方头平端紧定螺钉 GB 821-88十字槽圆柱头螺钉 GB /T 822-2000十字槽小盘头螺钉 GB 823-88吊环螺钉 GB 825-88开槽盘头定位螺钉 GB 828-88开槽圆柱端定位螺钉 GB 829-88开槽圆柱头轴位螺钉 GB 830-88开槽无头轴位螺钉 GB 831-88开槽带孔球面圆柱头螺钉 GB 832-88开槽大圆柱头螺钉 GB 833-88滚花高头螺钉 GB 834-88六角头自攻螺钉 GB 5285-85十字槽盘头自攻锁紧螺钉 GB 6560-86十字槽沉头自攻锁紧螺钉 GB 6561-86十字槽半沉头自攻锁紧螺钉 GB 6562-86六角头自攻锁紧螺钉 GB 6563-86内六角花形圆柱头自攻锁紧螺钉 GB 6564-86十字槽头凹穴六角头自攻螺钉 GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端 GB /T 13806.2-92 墙板自攻螺钉 GB /T 14210-93十字槽盘头自钻自攻螺钉 GB /T 15856.1-2002十字槽沉头自钻自攻螺钉 GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉 GB /T 15856.3-2002六角法兰面自钻自攻螺钉 GB /T 15856.4-2002六角凸缘自钻自攻螺钉 GB /T 15856.5-2002六角凸缘自攻螺钉 GB /T 16824.1-1997六角法兰面自攻螺钉 GB /T 16824.2-1997螺栓方头螺栓 C级 GB 8-88沉头方颈螺栓 GB 10-88沉头带榫螺拴 GB 11-88半圆头方颈螺栓 GB 12-88半圆头带榫螺栓 GB 13-88大半圆头方颈螺栓 C级 GB 14-1998大半圆头带榫螺栓 GB 15-88六角头铰制孔用螺栓 GB 27-88 滚花平头螺钉 GB 835-88滚花小头螺钉 GB 836-88垫圈标准型弹簧垫圈 GB 93-87平垫圈 C级 GB /T 95-2002大垫圈 A级 GB /T 96.1-2002大垫圈 C级 GB /T 96.2-2002平垫圈 A级 GB /T 97.1-2002平垫圈倒角型 A级 GB /T 97.2-2002销轴用平垫圈 GB /T 97.3-2000平垫圈用于螺钉和垫圈组合件 GB /T 97.4-2002平垫圈用于自攻螺钉和垫圈组合件 GB /T 97.5-2002 小垫圈 A级 GB /T 848-2002球面垫圈 GB 849-88锥面垫圈 GB 850-88开口垫圈 GB 851-88工字钢用方斜垫圈 GB 852-88槽钢用方斜垫圈 GB 853-88单耳止动垫圈 GB 854-88双耳止动垫圈 GB 855-88外舌止动垫圈 GB 856-88圆螺母用止动垫圈 GB 858-88轻型弹簧垫圈 GB 859-87鞍形弹性垫圈 GB 860-87内齿锁紧垫圈 GB 861.1-87六角头螺杆带孔铰制孔用螺栓 GB 28-88六角头头部带槽螺栓 A 和 B 级 GB 29.1-88十字槽凹穴六角头螺栓 GB 29.2-88六角头螺杆带孔螺栓 GB 31.1-88六角头螺杆带孔螺栓细杆 B级 GB 31.2-88六角头螺杆带孔螺栓细牙 A和B级 GB 31.3-88 六角头头部带孔螺栓 A 和 B级 GB 32.1-88六角头头部带孔螺栓细杆 B级 GB 32.2-88六角头头部带孔螺栓细牙 A 和 B 级 GB 32.3-88 下方头螺栓 B级 GB 35-88T 形槽用螺栓 GB 37-88加强半圆头方颈螺栓 GB /T794-93活节螺栓 GB 798-88地脚螺栓 GB 799-88沉头双榫螺 GB 800-88小圆半头低方颈螺栓 B级 GB /T 801-1998六角头螺栓 C级 GB /T 5780-2000六角头螺栓全螺纹 C级 GB /T 5781-2000六角头螺栓 GB /T 5782-2000六角头螺栓全螺纹 GB /T 5783-2000六角头螺栓-细杆-B级 GB 5784-86六角头螺栓细牙 GB /T 5785-2000六角头螺栓细牙全螺纹 GB /T 5786-2000六角法兰面螺栓-加大系列-B级 GB 5789-86六角法兰面螺栓-加大系列-细杆-B级 GB 5790-86 六角法兰面螺栓小系列 GB /T 16674-1996 内锯齿锁紧垫圈 GB 861.2-87外齿锁紧垫圈 GB 862.1-87外锯齿锁紧垫圈 GB 862.2-87波形弹性垫圈 GB 955-87锥形弹性垫圈 GB 956.1-87锥形锯齿锁紧垫圈 GB 956.2-87特大垫圈 C级 GB /T 5287-2002重型弹簧垫圈 GB 7244-87鞍形弹簧垫圈 GB 7245-87波形弹簧垫圈 GB 7246-87销开口销 GB /T 91-2000圆锥销 GB /T 117-2000内螺纹圆锥销 GB /T 118-2000圆柱销不淬硬钢和奥氏体不锈钢 GB /T 119.1-2000圆柱销淬硬钢和马氏体不锈钢 GB /T 119.2-2000内螺纹圆柱销不淬硬钢和奥氏体不锈钢 GB /T 120.1-2000 内螺纹圆柱销淬硬钢和马氏体不锈钢 GB /T 120.2-2000 开尾圆锥销 GB 877-76螺纹圆柱销 GB 878-86弹性圆柱销直槽重型 GB /T 879.1-2000弹性圆柱销直槽轻型 GB /T 879.2-2000弹性圆柱销卷制重型 GB /T 879.3-2000弹性圆柱销卷制标准型 GB /T 879.4-2000弹性圆柱销卷制轻型 GB /T 879.5-2000钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997螺柱双头螺柱 bm=1d GB 897-88双头螺柱 bm=1.25d GB 898-88双头螺柱 bm=1.5d GB 899-88双头螺柱 bm=2d GB 900-88等长双头螺柱 B级 GB 901-88手工焊用焊接螺柱 GB 902.1-89机动弧焊用焊接螺柱 GB 902.2-89储能焊用焊接螺柱 GB 902.3-89等长双头螺柱 C级 GB 953-88螺杆 GB /T 15389-94螺母方螺母 C级 GB 39-88六角螺母 C级 GB /T41-2000六角厚螺母 GB 56-88蝶形螺母 GB 62-88环形螺母 GB 63-88组合式盖形螺母 GB 802-88球面六角螺母 GB 804-88扣紧螺母 GB 805-88滚花高螺母 GB 806-88滚花薄螺母 GB 807-88小六角特扁细牙螺母 GB 808-88 带孔销 GB 880-86螺尾锥销 GB /T 881-2000销轴 GB 882-86槽销平行沟槽 GB /T 13829.1-92 槽销锥销 GB /T 13829.2-92槽销圆头沉头 GB /T 13829.3-92木螺钉开槽圆头木螺钉 GB 99-86开槽沉头木螺钉 GB 100-86开槽半沉头木螺钉 GB 101-86六角头木螺钉 GB 102-86十字槽圆头木螺钉 GB 950-86十字槽沉头木螺钉 GB 951-86十字槽半沉头木螺钉 GB 952-86柳钉平头铆钉 GB 109-86标牌铆钉 GB 827-86半圆头铆钉 GB 863.1-86小半圆头铆钉 GB 863.2-86平锥头铆钉 GB 864-86沉头铆钉 GB 865-86半沉头铆钉 GB 866-86半圆头铆钉 GB 867-86平锥头铆钉 GB 868-86嵌装圆螺母 GB 809-88小圆螺母 GB 810-88圆螺母 GB 812-88端面带孔圆螺母 GB 815-88侧面带孔圆螺母 GB 816-88带槽圆螺母 GB 817-881型非金属嵌件六角锁紧螺母 GB /T 889.1-20001型非金属嵌件六角锁紧螺母细牙 GB /T 889.2-2000盖形螺母 GB 923-881型六角螺母 GB /T 6170-20001型六角螺母细牙 GB /T 6171-2000六角薄螺母 GB /T 6172.1-2000非金属嵌件六角锁紧薄螺母 GB /T 6072.2-2000六角薄螺母细牙 GB /T 6173-2000六角薄螺母无倒角 GB /T 6174-20002型六角螺母 GB /T 6175-20002型六角螺母细牙 GB /T 6176-2000六角法兰面螺母 GB /T 6177.1-2000六角法兰面螺母细牙 GB /T 6177.2-20001型六角开槽螺母-A和B级 GB 6178-861型六角开槽螺母-C级 GB 6179-862型六角开槽螺母-A和B级 GB 6180-86六角开槽薄螺母-A和B级 GB 6181-862型非金属嵌件六角锁紧螺母 GB /T 6182-2000非金属嵌件六角法兰面锁紧螺母 GB /T 6183.1-2000非金属嵌件六角法兰面锁紧螺母细牙 GB /T 6183.2-2000 沉头铆钉 GB 869-86半沉头铆钉 GB 870-86扁圆头铆钉 GB 871-86扁平头铆钉 GB 872-86扁圆头半空心铆钉 GB 873-86沉头半空心铆钉 GB 874-86 120°扁平头半空心铆钉 GB 875-86空心铆钉 GB 876-86沉头铆钉 GB 954-86 120°管状铆钉 GB 975-86大扁圆头铆钉 GB 1011-86半沉头铆钉 GB 1012-86 120°平锥头半空心铆钉 GB 1013-86大扁圆头半空心铆钉 GB 1014-86沉头半空心铆钉 GB 1015-86无头铆钉 GB 1016-86封闭型扁圆头抽芯铆钉 GB 12615-90封闭型沉头抽芯铆钉 GB 12616-90开口型沉头抽芯铆钉 GB 12617-90开口型扁圆头抽芯铆钉 GB 12618-90扁圆头击芯铆钉 GB /T 15855.1-1995沉头击芯铆钉 GB /T 15855.2-1995紧固件-组合件和连接副钢结构用高强度大六角头螺栓 GB /T 1228-91 钢结构用高强度大六角头螺母 GB /T 1229-91 钢结构用高强度垫圈 GB /T 1230-911型全金属六角锁紧螺母 GB /T 6184-20002型全金属六角锁紧螺母 GB /T 6185.1-20002型全金属六角锁紧螺母细牙 GB /T 6185.2-20002型全金属六角锁紧螺母 9级 GB /T 6186-2000全金属六角法兰面锁紧螺母 GB /T 6187.1-2000全金属六角法兰面锁紧螺母细牙 GB /T 6187.2-2000 1型六角开槽螺母细牙 A和B级 GB 9457-882型六角开槽螺母细牙 A和B级 GB 9458-88六角开槽薄螺母细牙 A和B级 GB 9459-88焊接方螺母 GB /T 13680-92焊接六角螺母 GB /T 13681-92平头铆螺母 GB /T 17880.1-1999沉头铆螺母 GB /T 17880.2-1999小沉头铆螺母 GB /T 17880.3-1999120°小沉头铆螺母 GB /T 17880.4-1999平头六角铆螺母 GB /T 17880.5-1999精密机械用六角螺母 GB /T 18195-2000螺钉开槽圆柱头螺钉 GB /T 65-2000开槽盘头螺钉 GB /T 67-2000开槽沉头螺钉 GB /T 68-2000开槽半沉头螺钉 GB /T 69-2000内六角圆柱头螺钉 GB /T 70.1-2000内六角平圆头螺钉 GB /T 70.2-2000内六角沉头螺钉 GB /T 70.3-2000 钢结构用扭剪型高强度螺栓连接副 GB /T 3632-1995螺栓或螺钉和平垫圈组合件 GB /T 9074.1-2002十字槽头螺钉和外锯齿锁紧垫圈组合件 GB 9074.2-88十字槽盘头螺钉和弹簧垫圈组合件 GB 9074.3-88十字槽盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.4-88十字槽小盘头螺钉和平垫圈组合件 GB 9074.5-88十字槽小盘头螺钉和大垫圈组合件 GB 9074.6-88十字槽小盘头螺钉和弹簧垫圈组合件 GB 9074.7-88十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.8-88十字槽沉头螺钉和锥形锁紧垫圈组合件 GB 9074.9-88十字槽半沉头螺钉和锥形锁紧垫圈组合件 GB 9074.10-88十字曹凹穴六角头螺栓和平垫圈组合件 GB 9074.11-88十字槽凹穴六角头螺栓和弹簧垫圈组合件 GB 9074.12-88十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.13-88 六角头螺栓和弹簧垫圈组合件 GB 9074.15-88六角头螺栓和外锯齿锁紧垫圈组合件 GB 9074.16-88六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.17-88自攻螺钉和平垫圈组合件 GB /T 9074.18-2002十字槽凹穴六角头自攻螺钉和平垫圈组合件 GB 9074.20-88十字槽凹穴六角头自攻螺钉和大垫圈组合件 GB 9074.21-88组合件用弹簧垫圈 GB 9074.26-88组合件用外锯齿锁紧垫圈 GB 9074.27-88组合件用锥形锁紧垫圈 GB 9074.28-88腰状杆螺柱连接副型式分类 GB /T 13807.1-92腰状杆螺柱连接副螺柱 GB /T 13087.2-92腰状杆螺柱连接副螺母、受力套管 GB /T 13087.3-92开槽锥端紧定螺钉 GB 71-85开槽锥端定位螺钉 GB 72-88开槽平端紧定螺钉 GB 73-85开槽凹端紧定螺钉 GB 74-85开槽长圆柱端紧定螺钉 GB 75-85内六角平端紧定螺钉 GB /T 77-2000 内六角锥端紧定螺钉 GB /T 78-2000 内六角圆柱端紧定螺钉 GB /T 79-2000 内六角凹端紧定螺钉 GB /T 80-2000 方头长圆柱球面端紧定螺钉 GB 83-88 方头凹端紧定螺钉 GB 84-88方头长圆柱端紧定螺钉 GB 85-88方头短圆柱锥端紧定螺钉 GB 86-88十字槽盘头螺钉 GB /T 818-2000六角头不脱出螺钉 GB 838-88滚花头不脱出螺钉 GB 839-88 焊钉电弧螺柱焊用圆柱头焊钉 GB /T 10433-2002 无头焊钉 GB 10432-89美制英制德标对照表——德制弹簧垫圈美制英制德标对照表——自攻螺钉。

德标、欧标、国际、国标对照表—— DIN EN ISO GB 对照表新德标旧德标 英文名 中文名 国标 DIN EN ISO 4014DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓 全螺纹 GB/T 5783-2000 DIN EN ISO 4018DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓 全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓 细牙 全螺纹 GB/T 5786-2000 DIN EN ISO 8765DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓 细牙 GB/T 5785-2000 DIN EN ISO 4032DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母 无倒角 GB/T 6174-2000 DIN EN ISO 8673DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母 细牙 GB/T 6171-2000 DIN EN ISO 8674DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母 细牙 GB/T 6176-2000 DIN EN ISO 8675DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母 细牙 GB/T 6173-2000 DIN EN ISO 4762DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉 GB/T 70.1-2000 DIN EN ISO 7380 Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉GB/T 70.2-2000DIN EN ISO 10642DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉 GB/T 65-2000 DIN EN ISO 1580DIN 85 Slotted pan head screws-Product grade A(ISO 1580:1994) 开槽盘头螺钉 GB/T 67-2000 DIN EN ISO 2009DIN 963 Slotted countersunk flat head screws(common head style)(ISO 2009:1994) 开槽沉头螺钉 GB/T 68-2000 DIN EN ISO 2010DIN 964 Countersunk slotted raised head screws(common head style)-Produce grade A(ISO 2010:1994) 开槽半沉头螺钉 GB/T 69-2000 DIN EN ISO 7045DIN 7985 Pan head screws with type H or type Z cross recess-Product grade A(ISO 7054:1994) 十字槽盘头螺钉 GB/T 818-2000 DIN EN ISO 7046-1DIN 965 Countersunk flat head screws (common head style)with type H or type Z cross recess,product grade A-Part 1:Steel of property class 4.8(ISO 7046-1:1994) 十字槽盘头螺钉 第1部分：钢4.8级 GB/T 819.1-2000 DIN EN ISO 7046-2DIN 965 Cross recessed countersunk flat head screws (common head style),product grade A-Part2:Steel of property class 8.8,stainless steel and nonferous metals(ISO 7046-2:1990) 十字槽沉头螺钉 第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 GB/T 819.2-1997 DIN EN ISO 7047DIN 966 Countersunk raised head screws (common head style) with type H or type Z cross recess-Product grade A(ISO 7047:1994) 十字槽半沉头螺钉 GB/T 820-2000 DIN EN ISO 7048Cross recessed cheese head screws (ISO 7048:1998) 十字槽圆柱头螺钉 GB/T 822-2000 DIN EN ISO 10644Screw and washer assemblies with plain washers-Washer hardness classes 200HV and 300HV(ISO 10644:1998) 螺栓或螺钉和平垫圈组合件 GB/T 9074.1-2002 DIN EN ISO 10510Tapping screw and washer assemblies with plain washers(ISO 10510l:1999) 自攻螺钉和平垫圈组合件 GB/T 9074.18-2002 IDN EN ISO 15480Hexagon washer head drilling screws with tapping screws thread (ISO 15480:1999) 六角凸缘自钻自攻螺钉 GB/T 15856.5-2002 IDN EN ISO 15481Cross recessed pan head drilling screws with tapping screw thread(ISO 15481:1999) 十字槽盘头自钻自攻螺钉 GB/T 15856.1-2002 IDN EN ISO 15482 Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482:1999) 十字槽沉头自钻自攻螺钉GB/T 15856.2-2002IDN EN ISO 15483Cross recessed raised countersunk head drilling screws with tapping screw thread(ISO 15483:1999) 十字槽半沉头自钻自攻螺钉 GB/T 15856.3-2002 DIN EN ISO 10669Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A （ISO 10669:1999) 平垫圈 用于自攻螺钉和垫圈组合件 GB/T 97.5-2002 DIN EN ISO 10673Plain washers for screw and washer assemblies - Small,normal and large series - Product grade A (ISO 10673:1998) 平垫圈 用于螺钉和垫圈组合件 GB/T 97.4-2002 DIN EN ISO 2338DIN 7 Parallel pins,of unhardened steel and austenitic stainless steel(ISO 2338:1997) 圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000 DIN EN ISO 8733DIN 7979 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel(ISO 8733:1997) 内螺纹圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 120.1-2000 DIN EN ISO 8734DIN 6325 Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)(ISO 8734:1997) 圆柱销 淬硬钢和马氏体不锈钢 GB/T 119.2-2000 DIN EN ISO 8735DIN 7979 Parallel pins with internal thread,of hardened steel and martensitic stainless steel(ISO 8735:1997) 内螺纹圆柱销 淬硬钢和马氏体不锈钢 GB/T 120.2-2000 DIN EN ISO 8748DIN 7344 Spring-type straight pins,coiled,heavy duty (ISO 8748:1997) 弹性圆柱销 卷制 重型 GB/T 879.3-2000 DIN EN ISO 8750DIN 7343 Spring-type straight pins,coiled,standard duty (ISO 8750:1997) 弹性圆柱销 卷制 标准型 GB/T 879.4-2000 DIN EN ISO 8751Spring-type straight pins,coiled,light duty （ISO 8751:1997) 弹性圆柱销 卷制 轻型 GB/T 879.5-2000 DIN EN ISO 8752DIN 1481 Spring-type straight pins,slotted,heavy duty (ISO 8752:1997) 弹性圆柱销 直槽 重型 GB/T 879.1-2000 DIN EN ISO 13337DIN 7346 Spring-type straight pins,slotted,light duty (ISO 13337:1997) 弹性圆柱销 直槽 轻型 GB/T 879.2-2000 DIN EN ISO 1234DIN 94 Split pins （ISO1234:1997) 开口销 GB/T 91-2000 DIN EN ISO 7089Plain washers-Normal series-Product grade A 平垫圈 A 级 GB/T 97.1-2002 DIN EN ISO 7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000) 平垫圈 倒角型 A 级 GB/T 97.2-2002 DIN EN ISO 7091Plain washers-Normal series-Product grade C(ISO 7091:2000) 平垫圈 C 级 GB/T 95-2002 DIN EN ISO 7092 Plain washers-Small series-Product grade A(ISO 7092:2000)小垫圈 A 级 GB/T 848-2002DIN EN ISO 7093-1 Plain washers-Large series-Part 1: Product grade A(ISO 70931-1:2000)大垫圈 A 级 GB/T 96.1-2002DIN EN ISO 7093-2Plain washers-Normal series-Part 3: Product grade C(ISO 70936-2:2000) 大垫圈 C 级 GB/T 96.2-2002 DIN EN ISO 7094Plain washers-Extra large series -Product grade C(ISO 7094:2000) 特大垫圈 C 级 GB/T 5287-2002 DIN EN ISO 7040DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 - Property classes 5,8 and 10(ISO 7040:1997) 1型非金属嵌件六角锁紧螺母 GB/T 889.1-2000 DIN EN ISO 7042DIN 980| DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2 - Property classes 5,8, 10 and 12(ISO 7042:1997) 2型全金属六角锁紧螺母 GB/T 6185.1-2000 DIN EN ISO 7719Prevailing torque type all-metal hexagon nuts,style 1- Property classes 5,8 and 10(ISO 7719:1997) 1型全金属六角锁紧螺母 GB/T 6184-2000 DIN EN ISO 10511DIN 985 Prevailing torque type hexagon thin nuts (with non-metallic insert )(ISO 10511:1997) 非金属嵌件六角锁紧薄螺母 GB/T 6072.2-2000 DIN EN ISO 10512DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1,with metric fine pitch thread-Property classes 6,8 and 10(ISO 10512:1997) 1型非金属嵌件六角锁紧螺母 细牙 GB/T 889.2-2000 DIN EN ISO 10513 DIN 980|DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2,with metric fine pitch thread - Property classes 8,10 and 12(ISO 10513:1997)2型全金属六角锁紧螺母 细牙GB/T 6185.2-2000原汁原味的德标 DIN (ISO、EN)、美标 IFI (ANSI, ASME, SAE)、公制美标、日标 JIS 资料！在螺纹紧固件的使用中应用的较广泛的是螺栓－螺母连接副的形式，应用的较多的是有预紧力的连接方式，预紧力的连接可以提高螺栓连接的可靠性、防松能力及螺栓的疲劳强度，并且能增强螺纹连接体的紧密性和刚度。

标准对照表序号 Item德国标准DIN-Standard中文品名Description in Chinese英文品名Desciption in English国际标准ISO-Standard中国标准GB-Standard1DIN1圆锥销Taper pins ISO2339GB117 2DIN7圆柱销Parallel pins ISO2339GB119-86 3DIN84开槽圆柱头螺钉Slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉Slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈Tab washers GB854 6DIN94开口销Split cooter pins ISO1234GB917DIN95开槽半沉头木螺钉Slotted raised csk head wood screws GB101 8DIN96开槽半圆头木螺钉Slotted round head wood screws GB999DIN97开槽沉头木螺钉Slotted countersunk head wood screws GB100 10DIN125-A平垫Plain washers ISO7089GB97.1-85 11DIN125-B平垫（带倒角）Mediun washers ISO7090GB97.2-85 12DIN126平垫Plain washers ISO709113DIN127-A重型弹垫Spring lock washers,tang ends GB7244 14DIN127-B标准弹垫Spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫Single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈Curved spring washers17DIN137-B波形弹垫Wave spring washers GB955 18DIN186T型方颈螺栓T-head blots with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销Taper pins with threaded end ISO873721DIN261T型头螺栓T-head bolts22DIN315AF蝶型螺母（美制）Wing nuts America form23DIN315DF蝶型螺母（德制）Wing nuts germany form GB62-88 24DIN316AF蝶型螺母（美制）Wing screws America form25DIN317DF蝶型螺母（德制）Wing screws germany form26DIN319圆球型盖型螺母Ball knobs27DIN404开槽带孔球面圆柱头蚴钉Slotted capstan screws GB832-8828DIN417开槽长圆柱端紧定螺钉Slotted set srews with full dog point ISO7435GB75-8529DIN427开槽平端紧定螺钉（半牙）Slotted set srews with chamfered end ISO2342GB73-8530DIN431小六角特薄细牙螺母Pip nuts with thread GB808-8831DIN432外舌止动垫圈External tap GB856-8832DIN433小垫圈(用于圆柱头螺钉)Washers for cheese head screws ISO7092GB848-9533DIN434方斜垫圈（U型）Square taper washers forU-sectionGB852-8834DIN435方斜垫圈（I型）Square taper washers forI-sectionsGB852-8835DIN436方垫圈Square washers36DIN438开槽凹端紧定螺钉Slotted set with cup point ISO7436GB74-85 37DIN439六角薄螺母Hexagon thin nuts ISO4035GB6172-86 38DIN439细牙六角薄螺母Hexagon thin nuts ISO8675GB6173-86 39DIN440木螺钉专用垫圈Rounds washers for wood constructions ISO709440DIN443密封帽Sealing caps,push-in type41DIN444活节螺栓B型Eye bolts form B GB798-88 42DIN462内舌止动垫圈Internal tab washers43DIN463双耳止动垫圈Washers with two taps GB855-88 44DIN464滚花高头螺钉Knurled thumb screws with collar GB834-88 45DIN465开槽滚花高头螺钉Slotted knurled thumb screws with collar46DIN466滚花高螺母Knurled thumb nuts with collar GB806-88 47DIN467滚花薄螺母Knurled thumb thin nuts GB807-88 48DIN470锁紧垫圈Sealing washers49DIN471轴用弹性垫圈Retaining rings for shafts(external),circlips GB893-86 50DIN472孔用弹性垫圈Retaining rings for bores(internal),circlips GB893.86 51DIN478方头带垫螺栓Square head bolts with collar52DIN479方头圆柱底端螺栓Square head bolts with half dog point53DIN480方头带垫关圆底端螺栓Square head bolts with collar,half dog point54DIN508T型槽螺母T-slot nuts ISO29955DIN525单头螺柱Single end studs56DIN529地脚螺栓Masonry bolts GB799-8857DIN546带槽圆螺母Slotted round nuts GB817-76 58DIN547端面带孔圆螺母Round nuts with drilled holes in one face GB815-88 59DIN551开槽平端紧定螺钉Slotted set screws with flat point ISO4776GB73-85 60DIN553开槽锥端紧定螺钉Slotted set screws with cone point ISO7434GB71-85 61DIN555六角螺母Hexagon nuts ISO403462DIN557方螺母-C Square nuts GB39-88 63DIN558六角头螺钉Hexagon screws ISO401864DIN561六角头圆柱端紧定螺钉Hexagon set screws with full dog point65DIN562薄型方螺母-B Square nuts without bevel (pressed nuts)66DIN571六角头木螺钉Hexgon head wood screw(coach screws)GB102-8667DIN580吊环螺钉Lifting eye bolts ISO3266GB825-76 68DIN582吊环螺母Lifting eye nuts标准对照表序号 Item 德国标准DIN-Standard中文品名Description in Chinese英文品名Desciption in English国际标准ISO-Standard中国标准GB-Standard69DIN601六角头螺栓Hexagon blots ISO401670DIN603大半圆头方颈螺栓（马车螺栓）Mushroom head square neck bolts(carriage bolts)ISO8677GB14-8871DIN604沉头带插销马车螺栓Flat countersunk nib bolts72DIN605沉头长方颈马车螺栓Flat countersunk long squareneck bolts73DIN607半圆头带插销马车螺栓Cup head nib bolts74DIN608沉头短方颈马车螺栓Flat countersunk short square neck bolts75DIN609六角头精配螺栓（长螺纹）Hexagon fitted bolts,long thread76DIN610六角头精配螺栓（短螺栓）Hexagon fitted bolts short thread77DIN653滚花平头螺钉Knurled thumb screws thin type GB835-88 78DIN660半圆头铆钉Round head rivets ISO1051GB867-86 79DIN661沉头铆钉Contersunk head rivets ISO1051GB869-86 80DIN662半沉头铆钉Raised contersunk head rivets ISO105181DIN674大扁头铆钉Mushroom head rivets ISO105182DIN703重型侧面带孔圆螺母Adjusting rings,heavy range(shafting collars)83DIN705侧面带孔圆螺母Adjusting rings,light range(shafting collars)GB816-88 84DIN741卡头Wire rope clips85DIN787T型槽螺钉T-slot screws ISO29986DIN835双头螺柱（牙长=2D）Studs-metal(end=2d)GB900-8887DIN906内六角锥型闭锁螺钉Hexagon socket pipe plugs,conical thread88DIN908内六角直型闭锁螺钉Thread89DIN909外六角锥型闭锁螺钉Thread90DIN910外六角直型闭锁螺钉Hexagon head screw plugs,cyl.thread91DIN911内六角扳手Socket wrenches ISO293692DIN912内六角圆柱头螺钉Hexagon socket cap screws ISO4762GB70-8593DIN913内六角平端紧定螺钉Hexagon socket set screws with falt point ISO4026GB77-8594DIN914内六角尖端紧定螺钉Hexagon socket set screws with cone point ISO4027GB78-8595DIN915内六角圆柱端紧定螺钉Hexagon socket set screws with dog point ISO4028GB79-85 96DIN916内六角凹端紧定螺钉Hexagon socket set screws with cup point ISO4029GB80-85 97DIN917薄型盲螺母Hexagon cap nuts98DIN920开槽小圆柱头螺钉Slotted short cheese head screws99DIN921开槽大圆柱头螺钉Slotted large cheese head screws GB838-88100DIN923开槽圆柱头轴肩螺钉Slotted pan head screw with shoulder GB830-88101DIN927开槽无头轴肩螺钉Slotted shoulder screws102DIN928焊接方螺母Square weld nuts GB/T13680-92103DIN929焊接六角螺母Hexagon weld nuts GB/T13681-92104DIN931六角头螺栓（全牙）Hexagon head screws ISO4014GB5782-86105DIN933六角头螺栓（半牙）Hexagon head screws ISO4017GB5783-86106DIN934六角头螺母（1型）Hexagon full nuts ISO4032GB6170-86 107DIN934细牙六角头螺母（1型）Hexagon full nuts ISO8673GB6171-86 108DIN935开槽六角螺母Hexagon slotted and castle nuts ISO7035GB6178-86 109DIN936六角头薄螺母Hexagon thin nuts ISO4035GB6172.1-86 110DIN937六角头开槽薄螺母Hexagon thin slotted and caslte nuts ISO7038GB6181-86111DIN938双头螺距（牙长=1D）Studs metal(end=1d)GB897-88112DIN939双头螺距（牙长=1.5D）Studs metal(end=1.25d)GB898-88113DIN940双头螺距（牙长=1.25D）Studs metal(end=1.5d)114DIN960六角头细牙螺栓（全牙）Hexagon head bolts,metric fine pitch thread ISO8765GB5785-86115DIN961六角头细牙螺栓（半牙）Hexagon head bolts,metric fine pitch thread ISO8676GB8786-86116DIN962头部穿孔六角头螺栓Additional shapes and versions for bolts117DIN963开槽沉头螺钉Slotted countersund head screws ISO2009GB68-85 118DIN964开槽半沉头螺钉Slotted raised countersunk oval head screws ISO2010GB69-85 119DIN965十字槽沉头螺钉Cross recessed countersunk head screws ISO7046GB819-85120DIN966十字槽半沉头螺钉Cross recessed raisedCountersunk head screwsISO7047GB820-85121DIN970六角头螺母Hexagon nuts type-1122DIN971六角头螺母Hexagon nuts type-2123DIN972细牙六角头螺母（2型）Hexagon nuts with fine thread124DIN975牙条（全螺纹）Threaded rods(studdings)ISO8674GB6176-86 125DIN976螺纹销Threaded pins(stud bolts)GB15389-94 126DIN979六角头开槽薄螺母（2型）Hexagon thin slotted and castle nuts127DIN980全金属六角锁紧螺母（1Prevaillng rorque type hexagon nuts,all metal nuts型）128DIN981圆螺母Locknuts ISO7199GB6184-86129DIN982六角头尼龙锁紧螺母Prevailing rorque type hexagon nuts,heavy type,withnylonISO2982GB812-88130DIN985六角头薄型尼龙锁紧螺母Prevalling torque type hoxagon nuts,heavy type,withnylonISO7040GB889.1-86131DIN986六角盖型尼龙锁紧螺母Preailling torque typedomed capnuts with nyloninsertISO10511GB6172.2-86132DIN988配合垫片Shim rings133DIN1052木材连接用垫片Washers for timber connectors134DIN1151沉头钢钉Round plain head nails135DIN1440销钉专用垫片A型Plain washers for clevis pins(A型)ISO8738 136DIN1441销钉专用垫片Plain washers for clevis pins137DIN1444带头销钉Clevis pins with head ISO2341上一页下一页序号 Item德国标准DIN-Standard中文品名Description in Chinese英文品名Desciption in English国际标准ISO-Standard中国标准GB-Standard138DIN1471圆锥型槽销Grooved pins,taper grooved ISO8744GB/T13829.2139DIN1472圆锥型槽销（半槽）Grooved pins,taper grooved half length ISO8745GB/T13829.2140DIN1473平行槽销（带倒角）Grooved pins,parallel grooved full length ISO8740141DIN1474前端凹槽槽销Grooved pins,reverve grooved half length ISO8741 142DIN1475中部凹槽槽销Grooved pins,center grooved ISO8742 143DIN1476圆头槽销Grooved pins with round head ISO8746 144DIN1477沉头槽销Grooved pins with countersunk head ISO8747145DIN1479六角螺母棒Turnuckles(center parts),made out of hexagonbar146DIN1480花蓝螺栓Turnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销Spring pins,heavy type ISO8752GB879-86 148DIN1587组合式盖型螺母Hexagon domed cap nuts GB802-88 149DIN1804开槽圆螺母 Slotted round nuts for hook spammer(配合沟头扳手)150DIN1816圆螺母（带插销孔）Round nuts with set holes 151DIN2093盘型弹簧垫圈Disc springs152DIN3017喉箍Hose clamps153DIN3404润滑油嘴（旋扭头）Lubricating nipples,button head154DIN3567管夹Shackles for conduilts155DIN3570U型螺栓Stirrup bolts(U-bolts)156DIN6319球面垫圈Spherical washers,conical seats GB849-88 157DIN6325圆柱销Parallel pins ISO8734158DIN6330厚六角螺母Hexagon nuts,1.5d GB56-88159DIN6331厚六角法兰面螺母Hexagon nuts,1.5d with collar GB6177-86160DIN6334长六角螺母Hexagon nuts,3d161DIN6797-A外齿锁紧垫圈External teeth lock washers GB862.1-87 162DIN6797-I内齿锁紧垫圈Internal teeth lock washers GB861.1-87 163DIN6798-A外锯齿锁紧垫圈External teeth serrated lock washers GB862.2-87 164DIN6798-I内锯齿锁紧垫圈Internal teeth serrated lock washers GB861.2-87 165DIN6799开口挡圈Retaining rings for shafts(E-rings),circlips GB896-76 166DIN6885平键（A型）Parallel keys(form A)ISO773/2491167DIN6888半圆键Woodruff keys ISO3912168DIN6899嵌环（支撑环）Thimbles169DIN6900机器螺钉和垫圈组合件Screws and washers assemblies170DIN6901自攻螺钉和垫圈组合件Tapping screws and washer assemblies GB9074.1-17171DIN6912薄型带孔内六角圆柱螺钉Hexagon cocket head cap screws withhole,low headGB9074.18-23172DIN6914大六角头螺栓Hexagon head bolts with large head (friction grip nolts)173DIN6915大六角螺母Hexagon nuts with large wideth across flat(friction grip nuts)174DIN6916大垫圈Round washers for friction grip bolts175DIN6917楔型方垫圈Spuare taper washers for friction grip bolts onT-176DIN6923六角法兰面螺母Hexagon flange nuts ISO4161GB6187-86177DIN6925全金属六角锁紧螺母（2型）Prevailing torque type hexagon nuts,allmetallic nutsISO7042GB6185.1-2000181DIN7346轻型弹性圆柱销Spring pins,light type ISO13337182DIN7349重型弹性圆柱销用垫圈Washers for bolts with heavy type spring pinss183DIN7500ISO公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread184DIN7504自攻自钻螺钉（多种头型）Self-drilling tapping screws185DIN7513开槽切削螺纹螺钉（多种头型）Thread cutting screws186DIN7516十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recess187DIN7965T型四爪螺母Tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副Hexagon head fitted bolts for steel structures GB1228/1229/1230189DIN7971开槽盘头自攻螺钉Pan head tapping screws with slot ISO1481GB5282-85190DIN7972开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482GB5283-85191DIN7973开槽半沉头自攻螺钉Raised sountersunk oval head tapping screwswith slotISO1483GB5284-85192DIN7976六角头自攻螺钉Hexagon tapping screws ISO1479GB5285-85193DIN7980圆柱头螺钉用弹簧垫圈Spring lock washers for screws with cylindricalheadsISO8738194DIN7981十字槽盘头自攻螺攻Pan head tapping screws with cross recessed ISO7049GB845-85195DIN7982十字槽沉头自攻螺攻Countersunk flat head tapping screws withcross recessedISO7050GB846-85196DIN7983十字槽半沉头自攻螺攻Raised countersunk oval head tapping screwswith crossISO7051GB847-86197DIN7984薄型内六角圆柱头螺钉Hexagon socket head cap screwswith,reduced head198DIN7985十字槽盘头螺钉Pan head screws with cross recessed ISO7045GB818-85 199DIN7989钢结构用垫圈Washers for steel structures GB1230-84200DIN7990钢结构用六角头螺栓Hexagon head bolts for steel structures GB1229-84201DIN7991内六角沉头螺钉Hexagon socket coutersunk head screws ISO10642202DIN7993轴用钢丝挡圈Roundwire snap rings for shafts GB895.2-86203DIN7995十字槽半沉头木螺钉Cross recessed raised countersunk head woodscrewsGB952-86204DIN7996十字槽圆头木螺钉Cross recessed round head wood screws GB950-86205DIN7997十字槽沉头木螺钉Cross recessed countersunk head woodscrewsGB951-86206DIN8140螺纹护套(普通、自锁等)Ciol inserts,coarse,fine thread,silf locking207DIN9021大外径垫圈Washers,outside diameter appro.3d ISO7093GB96-85 208DIN11024弹簧卡子sping cotter for a bolt209DIN13257平板螺栓Belting bolts (elevator bolts)210DIN18182干壁钉（墙板钉）Dry wall screws211DIN28129环型螺母Lifting nuts(eye nuts)GB63-88212DIN70952圆螺母用止退垫圈Tab washer for slotted round nuts GB/858-88上一页。

紧固件规格标准——GB标准档圈锥销锁紧档圈 GB 883-86螺钉锁紧档圈 GB 884-86带锁圈的螺钉锁紧档圈 GB 885-86 轴肩档圈 GB 886-86螺钉紧固轴端档圈 GB 891-86螺栓紧固轴端档圈 GB 892-86孔用弹性档圈-A型 GB 893.1-86 孔用弹性档圈-B型 GB 893.2-86 轴用弹性档圈-A型 GB 894.1-86 轴用弹性档圈-B型 GB 894.2-86 孔用钢丝档圈 GB 895.1-86轴用钢丝档圈 GB 895.2-86开口档圈 GB 896-86钢丝锁圈 GB 921-86夹紧档圈 GB 960-86自攻螺钉十字槽盘头自攻螺钉 GB 845-85 十字槽沉头自攻螺钉 GB 846-85 十字槽半沉头自攻螺钉 GB 847-85 开槽盘头自攻螺钉 GB 5282-85开槽沉头自攻螺钉 GB 5283-85开槽半沉头自攻螺钉 GB 5284-85 塑料滚花头螺钉 GB 840-88开槽球面圆柱头轴位螺钉 GB 946-88开槽球面大圆柱头螺钉 GB 947-88开槽沉头不脱出螺钉 GB 948-88开槽半沉头不脱出螺钉 GB 949-88内六角花形盘头螺钉 GB 2672-86内六角花形沉头螺钉 GB 2673-86内六角花形半沉头螺钉 GB 2674-86内六角圆柱头轴肩螺钉 GB 5281-85内六角花形圆柱头螺钉-4.8级 GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级 GB 6191-86 精密机械用紧固件十字槽螺钉 GB /T 13806.1-92 十字槽半沉头螺钉 GB /T 820-2000方头平端紧定螺钉 GB 821-88十字槽圆柱头螺钉 GB /T 822-2000十字槽小盘头螺钉 GB 823-88吊环螺钉 GB 825-88开槽盘头定位螺钉 GB 828-88开槽圆柱端定位螺钉 GB 829-88开槽圆柱头轴位螺钉 GB 830-88开槽无头轴位螺钉 GB 831-88开槽带孔球面圆柱头螺钉 GB 832-88开槽大圆柱头螺钉 GB 833-88滚花高头螺钉 GB 834-88六角头自攻螺钉 GB 5285-85十字槽盘头自攻锁紧螺钉 GB 6560-86十字槽沉头自攻锁紧螺钉 GB 6561-86十字槽半沉头自攻锁紧螺钉 GB 6562-86六角头自攻锁紧螺钉 GB 6563-86内六角花形圆柱头自攻锁紧螺钉 GB 6564-86十字槽头凹穴六角头自攻螺钉 GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端 GB /T 13806.2-92 墙板自攻螺钉 GB /T 14210-93十字槽盘头自钻自攻螺钉 GB /T 15856.1-2002十字槽沉头自钻自攻螺钉 GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉 GB /T 15856.3-2002六角法兰面自钻自攻螺钉 GB /T 15856.4-2002六角凸缘自钻自攻螺钉 GB /T 15856.5-2002六角凸缘自攻螺钉 GB /T 16824.1-1997六角法兰面自攻螺钉 GB /T 16824.2-1997螺栓方头螺栓 C级 GB 8-88沉头方颈螺栓 GB 10-88沉头带榫螺拴 GB 11-88半圆头方颈螺栓 GB 12-88半圆头带榫螺栓 GB 13-88大半圆头方颈螺栓 C级 GB 14-1998大半圆头带榫螺栓 GB 15-88六角头铰制孔用螺栓 GB 27-88 滚花平头螺钉 GB 835-88滚花小头螺钉 GB 836-88垫圈标准型弹簧垫圈 GB 93-87平垫圈 C级 GB /T 95-2002大垫圈 A级 GB /T 96.1-2002大垫圈 C级 GB /T 96.2-2002平垫圈 A级 GB /T 97.1-2002平垫圈倒角型 A级 GB /T 97.2-2002销轴用平垫圈 GB /T 97.3-2000平垫圈用于螺钉和垫圈组合件 GB /T 97.4-2002平垫圈用于自攻螺钉和垫圈组合件 GB /T 97.5-2002 小垫圈 A级 GB /T 848-2002球面垫圈 GB 849-88锥面垫圈 GB 850-88开口垫圈 GB 851-88工字钢用方斜垫圈 GB 852-88槽钢用方斜垫圈 GB 853-88单耳止动垫圈 GB 854-88双耳止动垫圈 GB 855-88外舌止动垫圈 GB 856-88圆螺母用止动垫圈 GB 858-88轻型弹簧垫圈 GB 859-87鞍形弹性垫圈 GB 860-87内齿锁紧垫圈 GB 861.1-87六角头螺杆带孔铰制孔用螺栓 GB 28-88六角头头部带槽螺栓 A 和 B 级 GB 29.1-88十字槽凹穴六角头螺栓 GB 29.2-88六角头螺杆带孔螺栓 GB 31.1-88六角头螺杆带孔螺栓细杆 B级 GB 31.2-88六角头螺杆带孔螺栓细牙 A和B级 GB 31.3-88 六角头头部带孔螺栓 A 和 B级 GB 32.1-88六角头头部带孔螺栓细杆 B级 GB 32.2-88六角头头部带孔螺栓细牙 A 和 B 级 GB 32.3-88 下方头螺栓 B级 GB 35-88T 形槽用螺栓 GB 37-88加强半圆头方颈螺栓 GB /T794-93活节螺栓 GB 798-88地脚螺栓 GB 799-88沉头双榫螺 GB 800-88小圆半头低方颈螺栓 B级 GB /T 801-1998六角头螺栓 C级 GB /T 5780-2000六角头螺栓全螺纹 C级 GB /T 5781-2000六角头螺栓 GB /T 5782-2000六角头螺栓全螺纹 GB /T 5783-2000六角头螺栓-细杆-B级 GB 5784-86六角头螺栓细牙 GB /T 5785-2000六角头螺栓细牙全螺纹 GB /T 5786-2000六角法兰面螺栓-加大系列-B级 GB 5789-86六角法兰面螺栓-加大系列-细杆-B级 GB 5790-86 六角法兰面螺栓小系列 GB /T 16674-1996 内锯齿锁紧垫圈 GB 861.2-87外齿锁紧垫圈 GB 862.1-87外锯齿锁紧垫圈 GB 862.2-87波形弹性垫圈 GB 955-87锥形弹性垫圈 GB 956.1-87锥形锯齿锁紧垫圈 GB 956.2-87特大垫圈 C级 GB /T 5287-2002重型弹簧垫圈 GB 7244-87鞍形弹簧垫圈 GB 7245-87波形弹簧垫圈 GB 7246-87销开口销 GB /T 91-2000圆锥销 GB /T 117-2000内螺纹圆锥销 GB /T 118-2000圆柱销不淬硬钢和奥氏体不锈钢 GB /T 119.1-2000圆柱销淬硬钢和马氏体不锈钢 GB /T 119.2-2000内螺纹圆柱销不淬硬钢和奥氏体不锈钢 GB /T 120.1-2000 内螺纹圆柱销淬硬钢和马氏体不锈钢 GB /T 120.2-2000 开尾圆锥销 GB 877-76螺纹圆柱销 GB 878-86弹性圆柱销直槽重型 GB /T 879.1-2000弹性圆柱销直槽轻型 GB /T 879.2-2000弹性圆柱销卷制重型 GB /T 879.3-2000弹性圆柱销卷制标准型 GB /T 879.4-2000弹性圆柱销卷制轻型 GB /T 879.5-2000钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997螺柱双头螺柱 bm=1d GB 897-88双头螺柱 bm=1.25d GB 898-88双头螺柱 bm=1.5d GB 899-88双头螺柱 bm=2d GB 900-88等长双头螺柱 B级 GB 901-88手工焊用焊接螺柱 GB 902.1-89机动弧焊用焊接螺柱 GB 902.2-89储能焊用焊接螺柱 GB 902.3-89等长双头螺柱 C级 GB 953-88螺杆 GB /T 15389-94螺母方螺母 C级 GB 39-88六角螺母 C级 GB /T41-2000六角厚螺母 GB 56-88蝶形螺母 GB 62-88环形螺母 GB 63-88组合式盖形螺母 GB 802-88球面六角螺母 GB 804-88扣紧螺母 GB 805-88滚花高螺母 GB 806-88滚花薄螺母 GB 807-88小六角特扁细牙螺母 GB 808-88 带孔销 GB 880-86螺尾锥销 GB /T 881-2000销轴 GB 882-86槽销平行沟槽 GB /T 13829.1-92 槽销锥销 GB /T 13829.2-92槽销圆头沉头 GB /T 13829.3-92木螺钉开槽圆头木螺钉 GB 99-86开槽沉头木螺钉 GB 100-86开槽半沉头木螺钉 GB 101-86六角头木螺钉 GB 102-86十字槽圆头木螺钉 GB 950-86十字槽沉头木螺钉 GB 951-86十字槽半沉头木螺钉 GB 952-86柳钉平头铆钉 GB 109-86标牌铆钉 GB 827-86半圆头铆钉 GB 863.1-86小半圆头铆钉 GB 863.2-86平锥头铆钉 GB 864-86沉头铆钉 GB 865-86半沉头铆钉 GB 866-86半圆头铆钉 GB 867-86平锥头铆钉 GB 868-86嵌装圆螺母 GB 809-88小圆螺母 GB 810-88圆螺母 GB 812-88端面带孔圆螺母 GB 815-88侧面带孔圆螺母 GB 816-88带槽圆螺母 GB 817-881型非金属嵌件六角锁紧螺母 GB /T 889.1-20001型非金属嵌件六角锁紧螺母细牙 GB /T 889.2-2000盖形螺母 GB 923-881型六角螺母 GB /T 6170-20001型六角螺母细牙 GB /T 6171-2000六角薄螺母 GB /T 6172.1-2000非金属嵌件六角锁紧薄螺母 GB /T 6072.2-2000六角薄螺母细牙 GB /T 6173-2000六角薄螺母无倒角 GB /T 6174-20002型六角螺母 GB /T 6175-20002型六角螺母细牙 GB /T 6176-2000六角法兰面螺母 GB /T 6177.1-2000六角法兰面螺母细牙 GB /T 6177.2-20001型六角开槽螺母-A和B级 GB 6178-861型六角开槽螺母-C级 GB 6179-862型六角开槽螺母-A和B级 GB 6180-86六角开槽薄螺母-A和B级 GB 6181-862型非金属嵌件六角锁紧螺母 GB /T 6182-2000非金属嵌件六角法兰面锁紧螺母 GB /T 6183.1-2000非金属嵌件六角法兰面锁紧螺母细牙 GB /T 6183.2-2000 沉头铆钉 GB 869-86半沉头铆钉 GB 870-86扁圆头铆钉 GB 871-86扁平头铆钉 GB 872-86扁圆头半空心铆钉 GB 873-86沉头半空心铆钉 GB 874-86 120°扁平头半空心铆钉 GB 875-86空心铆钉 GB 876-86沉头铆钉 GB 954-86 120°管状铆钉 GB 975-86大扁圆头铆钉 GB 1011-86半沉头铆钉 GB 1012-86 120°平锥头半空心铆钉 GB 1013-86大扁圆头半空心铆钉 GB 1014-86沉头半空心铆钉 GB 1015-86无头铆钉 GB 1016-86封闭型扁圆头抽芯铆钉 GB 12615-90封闭型沉头抽芯铆钉 GB 12616-90开口型沉头抽芯铆钉 GB 12617-90开口型扁圆头抽芯铆钉 GB 12618-90扁圆头击芯铆钉 GB /T 15855.1-1995沉头击芯铆钉 GB /T 15855.2-1995紧固件-组合件和连接副钢结构用高强度大六角头螺栓 GB /T 1228-91 钢结构用高强度大六角头螺母 GB /T 1229-91 钢结构用高强度垫圈 GB /T 1230-911型全金属六角锁紧螺母 GB /T 6184-20002型全金属六角锁紧螺母 GB /T 6185.1-20002型全金属六角锁紧螺母细牙 GB /T 6185.2-20002型全金属六角锁紧螺母 9级 GB /T 6186-2000全金属六角法兰面锁紧螺母 GB /T 6187.1-2000全金属六角法兰面锁紧螺母细牙 GB /T 6187.2-2000 1型六角开槽螺母细牙 A和B级 GB 9457-882型六角开槽螺母细牙 A和B级 GB 9458-88六角开槽薄螺母细牙 A和B级 GB 9459-88焊接方螺母 GB /T 13680-92焊接六角螺母 GB /T 13681-92平头铆螺母 GB /T 17880.1-1999沉头铆螺母 GB /T 17880.2-1999小沉头铆螺母 GB /T 17880.3-1999120°小沉头铆螺母 GB /T 17880.4-1999平头六角铆螺母 GB /T 17880.5-1999精密机械用六角螺母 GB /T 18195-2000螺钉开槽圆柱头螺钉 GB /T 65-2000开槽盘头螺钉 GB /T 67-2000开槽沉头螺钉 GB /T 68-2000开槽半沉头螺钉 GB /T 69-2000内六角圆柱头螺钉 GB /T 70.1-2000内六角平圆头螺钉 GB /T 70.2-2000内六角沉头螺钉 GB /T 70.3-2000 钢结构用扭剪型高强度螺栓连接副 GB /T 3632-1995螺栓或螺钉和平垫圈组合件 GB /T 9074.1-2002十字槽头螺钉和外锯齿锁紧垫圈组合件 GB 9074.2-88十字槽盘头螺钉和弹簧垫圈组合件 GB 9074.3-88十字槽盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.4-88十字槽小盘头螺钉和平垫圈组合件 GB 9074.5-88十字槽小盘头螺钉和大垫圈组合件 GB 9074.6-88十字槽小盘头螺钉和弹簧垫圈组合件 GB 9074.7-88十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.8-88十字槽沉头螺钉和锥形锁紧垫圈组合件 GB 9074.9-88十字槽半沉头螺钉和锥形锁紧垫圈组合件 GB 9074.10-88十字曹凹穴六角头螺栓和平垫圈组合件 GB 9074.11-88十字槽凹穴六角头螺栓和弹簧垫圈组合件 GB 9074.12-88十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.13-88 六角头螺栓和弹簧垫圈组合件 GB 9074.15-88六角头螺栓和外锯齿锁紧垫圈组合件 GB 9074.16-88六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.17-88自攻螺钉和平垫圈组合件 GB /T 9074.18-2002十字槽凹穴六角头自攻螺钉和平垫圈组合件 GB 9074.20-88十字槽凹穴六角头自攻螺钉和大垫圈组合件 GB 9074.21-88组合件用弹簧垫圈 GB 9074.26-88组合件用外锯齿锁紧垫圈 GB 9074.27-88组合件用锥形锁紧垫圈 GB 9074.28-88腰状杆螺柱连接副型式分类 GB /T 13807.1-92腰状杆螺柱连接副螺柱 GB /T 13087.2-92腰状杆螺柱连接副螺母、受力套管 GB /T 13087.3-92开槽锥端紧定螺钉 GB 71-85开槽锥端定位螺钉 GB 72-88开槽平端紧定螺钉 GB 73-85开槽凹端紧定螺钉 GB 74-85开槽长圆柱端紧定螺钉 GB 75-85内六角平端紧定螺钉 GB /T 77-2000 内六角锥端紧定螺钉 GB /T 78-2000 内六角圆柱端紧定螺钉 GB /T 79-2000 内六角凹端紧定螺钉 GB /T 80-2000 方头长圆柱球面端紧定螺钉 GB 83-88 方头凹端紧定螺钉 GB 84-88方头长圆柱端紧定螺钉 GB 85-88方头短圆柱锥端紧定螺钉 GB 86-88十字槽盘头螺钉 GB /T 818-2000六角头不脱出螺钉 GB 838-88滚花头不脱出螺钉 GB 839-88 焊钉电弧螺柱焊用圆柱头焊钉 GB /T 10433-2002 无头焊钉 GB 10432-89美制英制德标对照表——德制弹簧垫圈美制英制德标对照表——自攻螺钉。

标准件标准区分标准件不同标准的区分德国的螺栓、螺母、垫圈国标DIN931、DIN934、DIN933、DINl27、DlNl25、DIN434、DIN912对应我国的国标DlNl 25-A ——平垫——B97.1-85DIN125-B——半垫（带倒角）——GB97.2-85DINl 27-A——重型弹畢——GB7244DIN127-B——标准弹垫——GB93-87DIN434——方斜垫圈（U型）——GB852-88DIN912——内六角圆柱头螺钉——GB70-85DIN931——六角头螺栓（半牙）——GB5782-86DIN933——六角头螺栓（全牙）——GB5783-86DIN934——六角头螺母（1型）——GB6170-86标准就是规范，每个国家和部门都有［|己的标准。

目前，我们在平时的业务中最常用到的标准有以下几种：GB-中国国家标准（国标）ANSl-美国国家标准（美标）DIN-徳国国家标准（徳标）ASME-美国机械工程师协会标准JIS-FI本国家标准（H标）BSW-英国国家标准GB-国家标准是我国众多标准中的一种，另外还有行业标准，专业标准和部门标准等。

国家标准又分：GB （强制性标准）和GB/T （推荐性标准）以及GBn（国家内部标准）等。

我们平常看到的像GB30. GB5783等等都是强制性的标准。

以上儿种标准除了一些基本尺寸如头部对边、头部厚度等的不同以外，最主要的是螺纹部分的不同。

GB、DIN、JIS等的螺纹都有是以MM （毫米）为单位，统称为公制螺纹。

另像ANSI、ASME等的螺纹是以英寸为单位的称为美标螺纹。

除了公制螺纹和美制螺纹外还有一种BSW-英制标准,其螺纹也是以英寸为单位，俗称惠氏螺纹。

公制螺纹是以MM （毫米）为单位，它的牙尖角为60度。

美制螺纹和英制螺纹都是以英寸为单位的。

美制螺纹的分尖角也是60度，而英制螺纹的分尖角为55度。

由于计暈单位的不同，导致了各种螺纹的表示方法也不尽相同。

序号中文品名德国标准DIN中国标准GB国际标准ISO英文品名1自攻自钻螺钉多种头型DIN7504GB15856.1-4Self-drilling tapping screws2平垫DIN125-A GB97.1-85ISO7089Plain washers3平垫（带倒角）DIN125-B GB97.2-85ISO7090Mediun washers4平垫DIN126ISO7091Plain washers5重型弹垫DIN127-A GB7244Spring lock washers,tang ends 6标准弹垫DIN127-B GB93-87Spring lock washers,square ends 7内六角扳手DIN911ISO2936Socket wrenches8内六角圆柱头螺钉DIN912GB70-85ISO4762Hexagon socket cap screws9内六角平端紧定螺钉DIN913GB77-85ISO4026Hexagon socket set screws with falt point10内六角尖端紧定螺钉DIN914GB78-85ISO4027Hexagon socket set screws with cone point11内六角圆柱端紧定螺钉DIN915GB79-85ISO4028Hexagon socket set screws with dog point12内六角凹端紧定螺钉DIN916GB80-85ISO4029Hexagon socket set screws with cup point13六角头螺栓）（半牙）DIN931GB5782-86ISO4014Hexagon head screws 14六角头螺栓（全牙）DIN933GB5783-86ISO4017Hexagon head screws15开槽沉头螺钉DIN963GB68-85ISO2009Slottedｃｏｕｎｔersund head screws16开槽半沉头螺钉DIN964GB69-85ISO2010Slotted raisedｃｏｕｎｔersunk oval head screws17十字槽沉头螺钉DIN965GB819-85ISO7046Cross recessedｃｏｕｎｔersunk head screws18十字槽半沉头螺钉DIN966GB820-85ISO7047Cross recessed raised19十字槽盘头自攻螺攻DIN7981GB845-85ISO7049Pan head tapping screws with cross recessed20十字槽沉头自攻螺攻DIN7982GB846-85ISO7050ｃｏｕｎｔersunk flat head tapping screws with cross21十字槽半沉头自攻螺攻DIN7983GB847-86ISO7051Raisedｃｏｕｎｔersunk oval head tapping screws with cross22开槽盘头自攻螺钉DIN7971GB5282-85ISO1481Pan head tapping screws with slot23开槽沉头自攻螺钉DIN7972GB5283-85ISO1482ｃｏｕｎｔersunk flat head tapping screws with slot24开槽半沉头自攻螺钉DIN7973GB5284-85ISO1483Raised sountersunk oval head tapping screws with slot25六角头自攻螺钉DIN7976GB5285-85ISO1479Hexagon tapping screws26十字槽盘头螺钉DIN7985GB818-85ISO7045Pan head screws with cross recessed27内六角沉头螺钉DIN7991ISO10642Hexagon socket coutersunk head screws28六角头尼龙锁紧螺母DIN982GB812-88ISO2982Prevailing rorque type hexagon nuts,heavy type,with nylon29六角头薄型尼龙锁紧螺母DIN985GB889.1-86ISO7040Prevalling torque type hoxagon nuts,heavy type,with nylon30六角盖型尼龙锁紧螺母DIN986GB6172.2-86ISO10511Preailling torque typedomed capnuts with nylonｉｎｓｅｒｔ中德螺丝标准对应表31六角头螺母（1型）DIN934GB6170-86ISO4032Hexagon full nuts 32细牙六角头螺母（1型）DIN934GB6171-86ISO8673Hexagon full nuts 33六角头薄螺母DIN936GB6172.1-86ISO4035Hexagon thin nuts 34六角薄螺母DIN439GB6172-86ISO4035Hexagon thin nuts35开槽半沉头木螺钉DIN95GB101Slotted raised csk head wood screws36开槽半圆头木螺钉DIN96GB99Slotted round head wood screws37开槽沉头木螺钉DIN97GB100Slottedｃｏｕｎｔersunk head wood screws38鞍形弹垫DIN128-A GB7245-87Single coil spring lock washers 39弹簧止动垫圈DIN137-A Curved spring washers40波形弹垫DIN137-B GB955Wave spring washers41T型方颈螺栓DIN186GB37-88T-head blots with square neck 42T型双接头螺栓DIN188T-head bolts with double nip43螺纹圆锥销DIN258ISO8737Taper pins with threaded end44T型头螺栓DIN261T-head bolts45蝶型螺母（美制）DIN315AF Wing nuts America form46蝶型螺母（德制）DIN315DF GB62-88Wing nuts germany form47蝶型螺母（美制）DIN316AF Wing screws America form48蝶型螺母（德制）DIN317DF Wing screws germany form49圆球型盖型螺母DIN319Ball knobs50开槽带孔球面圆柱头蚴钉DIN404GB832-88Slotted capstan screws51开槽长圆柱端紧定螺钉DIN417GB75-85ISO7435Slotted set srews with full dog point52开槽平端紧定螺钉（半牙）DIN427GB73-85ISO2342Slotted set srews with chamfered end53小六角特薄细牙螺母DIN431GB808-88Pip nuts with thread54外舌止动垫圈DIN432GB856-88External tap55小垫圈(用于圆柱头螺钉)DIN433GB848-95ISO7092Washers for cheese head screws 56方斜垫圈（U型）DIN434GB852-88Square taper washers for57方斜垫圈（I型）DIN435GB852-88Square taper washers for58方垫圈DIN436Square washers59开槽凹端紧定螺钉DIN438GB74-85ISO7436Slotted set with cup point60细牙六角薄螺母DIN439GB6173-86ISO8675Hexagon thin nuts61木螺钉专用垫圈DIN440ISO7094Rounds washers for wood constructions62密封帽DIN443Sealing caps,push-in type63活节螺栓B型DIN444GB798-88Eye bolts form B64内舌止动垫圈DIN462Internal tab washers65双耳止动垫圈DIN463GB855-88Washers with two taps66滚花高头螺钉DIN464GB834-88Knurled thumb screws with collar67开槽滚花高头螺钉DIN465Slotted knurled thumb screws with collar68滚花高螺母DIN466GB806-88Knurled thumb nuts with collar 69滚花薄螺母DIN467GB807-88Knurled thumb thin nuts70锁紧垫圈DIN470Sealing washers71轴用弹性垫圈DIN471GB893-86Retaining rings for shafts(external),circlips72孔用弹性垫圈DIN472GB893.86Retaining rings for bores(internal),circlips73方头带垫螺栓DIN478Square head bolts with collar74方头圆柱底端螺栓DIN479Square head bolts with half dog point75方头带垫关圆底端螺栓DIN480Square head bolts with collar,half dog point76T型槽螺母DIN508ISO299T-slot nuts77单头螺柱DIN525Single end studs 78地脚螺栓DIN529GB799-88Masonry bolts79带槽圆螺母DIN546GB817-76Slotted round nuts80端面带孔圆螺母DIN547GB815-88Round nuts with drilled holes in one face81开槽平端紧定螺钉DIN551GB73-85ISO4776Slotted set screws with flat point82开槽锥端紧定螺钉DIN553GB71-85ISO7434Slotted set screws with cone point83六角螺母DIN555ISO4034Hexagon nuts 84方螺母-C DIN557GB39-88Square nuts85六角头螺钉DIN558ISO4018Hexagon screws86六角头圆柱端紧定螺钉DIN561Hexagon set screws with full dog point87薄型方螺母-B DIN562Square nuts without bevel 88六角头木螺钉DIN571GB102-86Hexgon head wood screw89吊环螺钉DIN580GB825-76ISO3266Lifting eye bolts90吊环螺母DIN582Lifting eye nuts91六角头螺栓DIN601ISO4016Hexagon blots92大半圆头方颈螺栓（马车螺栓）DIN603GB14-88ISO8677Mushroom head square neckbolts(carriage bolts)93沉头带插销马车螺栓DIN604Flatｃｏｕｎｔersunk nib bolts94沉头长方颈马车螺栓DIN605Flatｃｏｕｎｔersunk long squareneck bolts95半圆头带插销马车螺栓DIN607Cup head nib bolts96沉头短方颈马车螺栓DIN608Flatｃｏｕｎｔersunk short square neck bolts97六角头精配螺栓（长螺纹）DIN609Hexagon fitted bolts,long thread 98六角头精配螺栓（短螺栓）DIN610Hexagon fitted bolts short thread 99滚花平头螺钉DIN653GB835-88Knurled thumb screws thin type 100半圆头铆钉DIN660GB867-86ISO1051Round head rivets101沉头铆钉DIN661GB869-86ISO1051Contersunk head rivets102半沉头铆钉DIN662ISO1051Raised contersunk head rivets103大扁头铆钉DIN674ISO1051Mushroom head rivets104重型侧面带孔圆螺母DIN703Adjusting rings,heavy range(shafting collars)105侧面带孔圆螺母DIN705GB816-88Adjusting rings,light range(shafting collars)106卡头DIN741Wire rope clips107T型槽螺钉DIN787ISO299T-slot screws108双头螺柱（牙长=2D）DIN835GB900-88Studs-metal(end=2d)109内六角锥型闭锁螺钉DIN906Hexagon socket pipe plugs,conical thread110内六角直型闭锁螺钉DIN908Thread 111外六角锥型闭锁螺钉DIN909Thread112外六角直型闭锁螺钉DIN910Hexagon head screw plugs,cyl.thread113薄型盲螺母DIN917Hexagon cap nuts114开槽小圆柱头螺钉DIN920Slotted short cheese head screws 115开槽大圆柱头螺钉DIN921GB838-88Slotted large cheese head screws116开槽圆柱头轴肩螺钉DIN923GB830-88Slotted pan head screw with shoulder117开槽无头轴肩螺钉DIN927Slotted shoulder screws118焊接方螺母DIN928GB/T13680-92Square weld nuts119焊接六角螺母DIN929GB/T13681-92Hexagon weld nuts120六角头螺母DIN970Hexagon nuts type-1121六角头螺母DIN971Hexagon nuts type-2122细牙六角头螺母（2型）DIN972Hexagon nuts with fine thread123开槽六角螺母DIN935GB6178-86ISO7035Hexagon slotted andｃａｓｔle nuts124六角头开槽薄螺母DIN937GB6181-86ISO7038Hexagon thin slotted and caslte nuts125双头螺距（牙长=1D）DIN938GB897-88Studs metal(end=1d) 126双头螺距（牙长=1.5D DIN939GB898-88Studs metal(end=1.25d)127双头螺距（牙长=1.25D DIN940Studs metal(end=1.5d)128六角头细牙螺栓（全牙）DIN960GB5785-86ISO8765Hexagon head bolts,metric fine pitch thread129六角头细牙螺栓（半牙）DIN961GB8786-86ISO8676Hexagon head bolts,metric fine pitch thread130头部穿孔六角头螺栓DIN962Additional shapes and versions for bolts131牙条（全螺纹）DIN975GB6176-86ISO8674Threaded rods(studdings) 132螺纹销DIN976GB15389-94Threaded pins(stud bolts)133六角头开槽薄螺母2型DIN979Hexagon thin slotted andｃａｓｔle nuts134全金属六角锁紧螺母1型DIN980Prevaillng rorque type hexagon nuts,all metal nuts135圆螺母DIN981GB6184-86ISO7199Locknuts136配合垫片DIN988Shim rings137木材连接用垫片DIN1052Washers for timber connectors 138沉头钢钉DIN1151Round plain head nails139销钉专用垫片A型DIN1440ISO8738Plain washers for clevis pins(A) 140销钉专用垫片DIN1441Plain washers for clevis pins 141带头销钉DIN1444ISO2341Clevis pins with head142圆锥型槽销DIN1471GB/T13829.2ISO8744Grooved pins,taper grooved143圆锥型槽销（半槽）DIN1472GB/T13829.2ISO8745Grooved pins,taper grooved half length144平行槽销（带倒角）DIN1473ISO8740Grooved pins,parallel grooved full length145前端凹槽槽销DIN1474ISO8741Grooved pins,reverve grooved half length146中部凹槽槽销DIN1475ISO8742Grooved pins,center grooved 147圆头槽销DIN1476ISO8746Grooved pins with round head148沉头槽销DIN1477ISO8747Grooved pins withｃｏｕｎｔersunk head149六角螺母棒DIN1479Turnuckles(center parts),made out of hexagon bar150花蓝螺栓DIN1480Turnuckles with eye bolt and hook bolt151弹性圆柱销DIN1481GB879-86ISO8752Spring pins,heavy type 152组合式盖型螺母DIN1587GB802-88Hexagon domed cap nuts153开槽圆螺母(配合沟头扳手)DIN1804Slotted round nuts for hook spammer154圆螺母（带插销孔）DIN1816Round nuts with set holes155盘型弹簧垫圈DIN2093Disc springs156喉箍DIN3017Hose clamps157润滑油嘴（旋扭头）DIN3404Lubricating nipples,button head 158管夹DIN3567Shackles for conduilts159U型螺栓DIN3570Stirrup bolts(U-bolts)160球面垫圈DIN6319GB849-88Spherical washers,conical seats 161圆柱销DIN6325ISO8734Parallel pins162厚六角螺母DIN6330GB56-88Hexagon nuts,1.5d163厚六角法兰面螺母DIN6331GB6177-86Hexagon nuts,1.5d with collar 164长六角螺母DIN6334Hexagon nuts,3d165外齿锁紧垫圈DIN6797-A GB862.1-87External teeth lock washers166内齿锁紧垫圈DIN6797-I GB861.1-87Internal teeth lock washers167外锯齿锁紧垫圈DIN6798-A GB862.2-87External teeth serrated lock washers168内锯齿锁紧垫圈DIN6798-I GB861.2-87Internal teeth serrated lock washers169开口挡圈DIN6799GB896-76Retaining rings for shafts(E-rings),circlips170平键（A型）DIN6885ISO773/2491Parallel keys(form A)171半圆键DIN6888ISO3912Woodruff keys172嵌环（支撑环）DIN6899Thimbles173机器螺钉和垫圈组合件DIN6900Screws and washers assemblies174自攻螺钉和垫圈组合件DIN6901GB9074.1-17Tapping screws and washer assemblies175薄型带孔内六角圆柱螺钉DIN6912GB9074.18-23Hexagon cocket head cap screwswith hole,low head176大六角头螺栓DIN6914Hexagon head bolts with large head177大六角螺母DIN6915Hexagon nuts with large wideth across flat178大垫圈DIN6916Round washers for friction grip bolts179楔型方垫圈DIN6917Spuare taper washers for friction grip bolts on T-180六角法兰面螺母DIN6923GB6187-86ISO4161Hexagon flange nuts181全金属六角锁紧螺母2型DIN6925GB6185.1-2000ISO7042Prevailing torque type hexagonnuts,all metallic nuts182轻型弹性圆柱销DIN7346ISO13337Spring pins,light type183重型弹性圆柱销用垫圈DIN7349Washers for bolts with heavy type spring pinss184ISO公制螺纹螺钉多种头型DIN7500Thread forming screws for ISO-metric thread185开槽切削螺纹螺钉（多种头型）DIN7513Thread cutting screws186十字槽切削螺纹螺钉（多种头型）DIN7516Thread cutting screws crossrecess187T型四爪螺母DIN7965Tee nuts with pronge188钢结构用六角头螺栓连接副DIN7968GB1228/1229/1230Hexagon head fitted bolts forsteel structures189圆柱头螺钉用弹簧垫圈DIN7980ISO8738Spring lock washers for screws with cylindrical heads190薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reduced head191钢结构用垫圈DIN7989GB1230-84Washers for steel structures192钢结构用六角头螺栓DIN7990GB1229-84Hexagon head bolts for steel structures193轴用钢丝挡圈DIN7993GB895.2-86Roundwire snap rings for shafts194十字槽半沉头木螺钉DIN7995GB952-86Cross recessed raisedｃｏｕｎｔersunk head wood screws195十字槽圆头木螺钉DIN7996GB950-86Cross recessed round head wood screws196十字槽沉头木螺钉DIN7997GB951-86Cross recessedｃｏｕｎｔersunk head wood screws197螺纹护套(普通、自锁等)DIN8140Ciolｉｎｓｅｒｔs,coarse,fine thread,silf locking198大外径垫圈DIN9021GB96-85ISO7093Washers,outside diameter appro.3d 199弹簧卡子DIN11024sping cotter for a bolt200平板螺栓DIN13257Belting bolts(elevator bolts)201干壁钉（墙板钉）DIN18182Dry wall screws202环型螺母DIN28129GB63-88Lifting nuts(eye nuts)203圆螺母用止退DIN70952Tab washer for slotted round nuts 204圆锥销DIN1GB117ISO2339Taper pins205圆柱销DIN7GB119-86ISO2339Parallel pins206开槽圆柱头螺钉DIN84GB65-85ISO1207Slotted cheese head screws207开槽盘头螺钉DIN85GB67-85ISO1580Slotted pan head screws208单耳止动垫圈DIN93GB854Tab washers209开口销DIN94GB91ISO1234ｓｐｌｉｔcooter pins。