诺瓦科技LED接收卡MRV220-15规格书英文版

MCTRL R5 Independent ControllerSp e cificationsCopyright © 2018 Xi ’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi ’an NovaStar Tech Co., Ltd.TrademarkChange HistoryContentsis a trademark of Xi ’an NovaStar Tech Co., Ltd. StatementYou are welcome to use the product of Xi ’an NovaStar Tech Co., Ltd. ( h ereinafter referred to as NovaStar). This document is intended to help you understand and use the product. For accuracy and reliability, NovaStar may make improvements and/or changes to this document at any time and without notice. Anyproblem in use or a ny good suggestion, please contact us through ways provided in the document. We will do our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible. Change HistoryChange History ................................................................................................................................ ii 11 Safety ...............................................................................................................................................1.1 Storage and Transport Safety (1)1.2 Installation and Use Safety .......................................................................................................................... 1 32 Overview ......................................................................................................................................... 3 Features ........................................................................................................................................... 4 4 Appearance ..................................................................................................................................... 5 Dimensions .................................................................................................................................... 75 6 8 Specifications .................................................................................................................................1 Safety1 S afetyThis chapter illustrates safety of the MCTRL R5 independent controller to ensure theproduct’s storage, transport, installation and use safety.Safety instructions are applicable to all personnel who contact or use the product.First of all, pay attention to following points.●Read through the instructions.●Retain all instructions.●Comply with all instructions.1.1 Storage and Transport Safety●Pay attention to dust and water prevention.●Avoid long-term direct sunlight.●Do not place the product at a position near fire and heat.●Do not place the product in an area containing explosive materials.●Do not place the product in a strong electromagnetic environment.●Place the product at a stable position to prevent damage or personal injurycaused by dropping.●Save the packing box and materials which will come in handy if you ever have tostore and ship the product. For maximum protection during storage and shipping,repack the product as it was originally packed at the factory.1.2 Installation and Use Safety●Only trained professionals may install the product.●Plugging and unplugging operations are prohibited when the power is on.●Ensure safe grounding of the product.●Beware of electric shock hazards.●Always wear a wrist band and insulating gloves.●Do not place the product in an area having frequent or strong shake.●Perform dust removing regularly.1 Safety●Contact NovaStar for maintenance at any time, rather than have the productdisassembled and maintained by non-professionals without authorization.●Replace faulty parts only with the spare parts supplied by NovaStar.2 O verview2OverviewDeveloped by NovaStar, the MCTRL R5 is the first independent controller that supports rotation function. With up to 3840×1080@60Hz loading capacity of a single unit, it can support any custom resolution within this range as required, thus meeting the on-site configuration requirements of extra-long or extra-large LED displays. Working with the A8s or A10s, the MCTRL R5 supports free screen configuration on SmartLCT, presenting full rotation of the display screen at any angle, adding diversity to images, and bringing different visual experience to users.The MCTRL R5 is mainly applied to concert control centers, live events, security monitoring, Olympic Games and various sports centers.3 F eatures3Features4 A ppearance●Provides complete input connectors, including 1 × 6G-SDI, 1 × dual-link DVI and1 × HDMI 1.4.●Supports 8 × Gigabit Ethernet ports and 2 × fiber optical outputs.●Supports rotation of LED screens at any angle.●Adopts innovative architectural design to enable smart configuration, which cangreatly shorten the stage preparation time.●Adopts NovaStar G4 engine to realize a perfect image display with no flickeringand scanning lines, but fine quality and good sense of depth.●Supports NovaStar's latest pixel level calibration technology with a fast andefficient process.●Implements white balance calibration and color gamut mapping to ensure colorsare faithfully reproduced.●Supports screen configuration at any time without a PC.●Supports easy and quick manual adjustment of screen brightness.●Supports hardware upgrade via USB on the front panel.●Supports cascading multiple controllers for uniform control.4 AppearanceRear PanelInput Voltage AC 100-240 V 50/60 Hz Rated Power Consumption 25 WOperating Temperature-20°C –60°C Operating Humidity10% RH –90% RH DimensionsWeight 4.3 kg5 Dimensions482.6 mm × 334.6 m m × 52 .0 mmIndependent Controller MCTRL R5 Specifications。

Product images provided in this file are for reference only , and the actual products shall prevail.Rev1.1.3 NS110100257SpecificationsReceiving Card MRV420OverviewMRV420 is the EMC version of MRV220 with its effective reduction ofthe electromagnetic radiation of the whole system.Features1)Single card outputs 24-group of RGB data;2)Single card outputs 28-group of RGB data;3)Single card outputs 64-group of serial data;4)Single card supports resolution of 256x226;5)Configuration file read back;6)Temperature monitoring;7)Ethernet cable communication status detection;8)Power supply voltage detection;9)Pixel-by-pixel brightness and chromaticity calibration, Brightness andchromaticity calibration coefficients for each LED; 10)Complywith EU CE-EMC Class B standard;11)Comply with RoHS standard.Output Interface DefinitionUnder all the two different working modes of it, two 60P interfaces canoutput different data. Each 60p contains two 30P with the samedefinition. Interfaces are defined as follows:24-groupSupport i37 D2 E2 38 37 D4 E4 3839 CTRL2 R7 40 39 CTRL4 R19 4041 G7 B7 42 41 G19 B19 4243 GND R8 44 43 GND R20 4445 G8 B8 46 45 G20 B20 4647 R9 G9 48 47 R21 G21 4849 B9 GND 50 49 B21 GND 5051 R10 G10 52 51 R22 G22 5253 B10 R11 54 53 B22 R23 5455 G11 B11 56 55 G23 B23 5657 R12 G12 58 57 R24 G24 5859 B12 VCC 60 59 B24 VCC 602)28-g23 B4 R5 24 23 B16 R17 2425 G5 B5 26 25 G17 B17 2627 R6 G6 28 27 R18 G18 28Supporting 64 sets of serial data, defined as follows:DimensionsAppearanceThickness of the board is about 2mm. The overall thickness ( b oard thickness ＋ t hickness of the components on front and back side) is about18 m m .Unit: mm.SpecificationsSpecific ModelAppendixSerial data decoding circuit ：To meet the needs of different customers, Nova has provided more specific models of the products, including standard products in stock. Other models need to be customized.。

MRV316Product DescriptionDocument Version:V1.0.0Receiving CardDocument Number: NS110100375Copyright © 2017 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi’an NovaStar Tech Co., Ltd. Product Description Change HistoryProduct DescriptionContentsChange HistoryTrademarkis a registered trademark of Xi’an NovaStar Tech Co., Ltd.StatementYou are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar ). This document is intended to help you understand and use the product. For accuracy and reliability,NovaStar may make improvements and/or changes to this document at any time and without notice. Any problem in use or any good suggestion, please contact u s through ways provided in the document. We will do our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible.Receiving Card MRV316ContentsChange History (ii)1Safety (1)2Overview (2)3F eatures (3)4Hardware (4)4.1Appearance (4)4.2Dimensions (5)4.3Indicators (5)4.4Definition of Data Interface (6)5Software Structure (8)Typical Networking ...................................................................................................................... 69 7 Specifications . (11)1 Safety1 SafetyThis chapter illustrates safety of the MRV316 receiving card to ensure the product’sstorage, transport, installation and use safety. Safety instructions are applicable to allpersonnel who contact or use the product. First of all, pay attention to following points.●Read through the instructions.●Retain all instructions.●Comply with all instructions.Storage and Transport Safety●Pay attention to dust and water prevention.●Avoid long-term direct sunlight.●Do not place the product at a position near fire and heat.●Do not place the product in an area containing explosive materials.●Do not place the product in a strong electromagnetic environment.●Place the product at a stable position to prevent damage or personal injurycaused by dropping.●Save the packing box and materials which will come in handy if you ever have tostore and ship the product. For maximum protection during storage and shipping,repack the product as it was originally packed at the factory.Installation and Use Safety●Only trained professionals may install the product.●Plugging and unplugging operations are prohibited when the power is on.●Ensure safe grounding of the product.●Always wear a wrist band and insulating gloves.●Do not place the product in an area having frequent or strong shake.●Perform dust removing regularly.●Contact NovaStar for maintenance at any time, rather than have the productdisassembled and maintained by non-professionals without authorization.●Replace faulty parts only with the spare parts supplied by NovaStar.2 Overview2OverviewThe MRV316 is a new receiving card developed by NovaStar. A single MRV316 loads up to 512x256 pixels.The MRV316 supports pixel level brightness and chroma calibration, which effectively removes color difference, greatly improves display consistency of LED images, and presents finer displays to users.Software and hardware designs of the MRV316 have fully concerned users' deployment, operating and maintenance scenarios, enabling easier deployment, more stable operating and more efficient maintenance.Hardware design:●Integrates 16 standard HUB75 connectors, which makes the HUB boardunnecessary.●Adopts the Gigabit Ethernet port, which can connect to the PC.Software design:●Supports pixel level brightness and chroma calibration.●Supports setting of images pre-stored in the receiving card.●Supports status detection of temperature, voltage, Ethernet cablecommunication and video source signals.●Supports the 5-pin LCD module.4Hardware4.1 AppearanceProduct images provided in this file are for reference only, and the actual productsshall prevail.4.2 DimensionsThe board thickness is not greater than 2.0 mm, and the total thickness (boardthickness + thickness of components on front and rear panels) is not greater than17.5 mm.The u n it of dimension chart is “mm”. The location holes are connected to signa lgrounds (GND).4.3Indicators4Powerindicator (red)Always onThe indicator will be always on after the power is on.4.45 SoftwareStructure5Software StructureFirmware in the delivery MRV316 includes MCU program and FPGA program. Program download method:Visit w ww.novastar-led.c n a nd change the user interface language to English at the top right. Then, on the displayed P roducts&Downloads page, click the target receiving card in the R eceiving Card section to enter its detail introduction page. At last, click D ownloads to enter the download list and download the required program packages.6 TypicalNetworkingReceiving Card MRV316Product Description6 Typical NetworkingFigure 6-2 No sending card mode6Typical NetworkingThe MRV316 is applied to the LED display synchronous system which is generally composed of the LED display, receiving card, LED display controller and controller peripherals. The receiving card is connected to the LED display over HUB connectors.The synchronous system requires connecting a computer to display the computer’s images and texts on the LED display. The synchronous system's structure is shown in the following figure.Figure 6-1 Sending card mode7 Specifications。

SpecificationsReceiving Card MRV420Product images provided in this file are for reference only , and the actual products shall prevail.Rev1.1.3NS110100257XI 'AN NOVA S TAR T E C H C O .,L T D.OverviewMRV420 is the EMC version of MRV220 with its effective reduction of the electromagnetic radiation of the whole system.Features1) Single card outputs 24-group of RGB data; 2)Single card outputs 28-group of RGB data;3) Single card outputs 64-group of serial data; 4) Single card supports resolution of 256x226; 5) Configuration file read back; 6) Temperature monitoring; 7) Ethernet cable communication status detection;8) Power supply voltage detection; 9)Pixel-by-pixel brightness and chromaticity calibration, Brightness and chromaticity calibration coefficients for each LED;10) Comply with EU CE-EMC Class B standard; 11) Comply with RoHS standard.XI 'A N NOV A S T A R T E C H C O .,L T D.Output Interface DefinitionUnder all the two different working modes of it, two 60P interfaces canoutput different data. Each 60p contains two 30P with the samedefinition. Interfaces are defined as follows:1)24-group data modeSupporting 24 sets of parallel data, defined as follows:X I'A NN OV AS TA RT EC HC O.,L TD.2)28-group data modeSupporting 28 sets of parallel data, Serial data decoding is required for scan mode above 1/8 scan (Serial data decoding circuit in the appendix) , defined as follows:X I'A NN OV AS TA RT EC HC3)64-group serial data modeSupporting 64 sets of serial data, defined as follows:D. L TDimensionsThickness of the board is about 2mm. The overall thickness (board thickness ＋thickness of the components on front and back side) is about 18mm.Unit: mm.XI 'AN NOVA S TAR T E C HCO .,L T D.Note: Product images provided in this file are for reference only, and the actual products shall prevail.J2 definition （Connector interface of the network ports ）J9 definition （Indicator Light Socket ）Indicator 2 Network PortsPower SocketHUBHUBMale connector Of network portsC HCO .,L T D.Specific Model ListTo meet the needs of different customers, Nova has provided more specific models of the products, including standard products in stock. Other models need to be customized.S T A R T E C H C O .,L T DAppendixSerial data decoding circuit：X I'A NN OV AS TA RT EC HC O.,L TD.。

MRV316Receiving CardV1.0.0Product DescriptionReceiving Card MRV316Copyright © 2017 Xi ’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi ’an NovaStar Tech Co., Ltd.Product Description Change HistoryProduct Description ContentsTrademark is a registered trademark of Xi ’an NovaStar Tech Co., Ltd.StatementYou are welcome to use the product of Xi ’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar ) . This document is intended to help you understand and use the product. For accuracy and reliability,NovaStar may make improvements and/or changes to this document at any time and without notice. Anyproblem in use or any good suggestion, please contact u s through ways provided in the document. We willdo our utmost to solve the problems and adopt the suggestions after evaluation as soon as possible.Change HistoryContentsChange History (ii)1 Safety ............................................................................................................................................... 1 2 Overview ......................................................................................................................................... 2 3 F eatures ........................................................................................................................................... 3 Hardware . (44)4.1 Appearance .................................................................................................................................................. 4 4.2 Dimensions .................................................................................................................................................. 5 4.3 Indicators ..................................................................................................................................................... 5 4.4 Definition of Data Interface .. (6)5 Software Structure ........................................................................................................................ 8 6 9 Typical Networking ...................................................................................................................... 7 Specifications . (11)1 Safety1 SafetyThis chapter illustrates safety of the MRV316 receiving card to ensure the product’sstorage, transport, installation and use safety. Safety instructions are applicable to allpersonnel who contact or use the product. First of all, pay attention to following points.●Read through the instructions.●Retain all instructions.●Comply with all instructions.Storage and Transport Safety●Pay attention to dust and water prevention.●Avoid long-term direct sunlight.●Do not place the product at a position near fire and heat.●Do not place the product in an area containing explosive materials.●Do not place the product in a strong electromagnetic environment.●Place the product at a stable position to prevent damage or personal injurycaused by dropping.●Save the packing box and materials which will come in handy if you ever have tostore and ship the product. For maximum protection during storage and shipping,repack the product as it was originally packed at the factory.Installation and Use Safety●Only trained professionals may install the product.●Plugging and unplugging operations are prohibited when the power is on.●Ensure safe grounding of the product.●Always wear a wrist band and insulating gloves.● Do not place the product in an area having frequent or strong shake. ● Perform dust removing regularly.● Contact NovaStar for maintenance at any time, rather than have the product disassembled and maintained by non-professionals without authorization. ●Replace faulty parts only with the spare parts supplied by NovaStar.2 Overview2OverviewThe MRV316 is a new receiving card developed by NovaStar. A single MRV316 loads up to 512x256 pixels.The MRV316 supports pixel level brightness and chroma calibration, which effectively removes color difference, greatly improves display consistency of LED images, and presents finer displays to users.Software and hardware designs of the MRV316 have fully concerned users'deployment, operating and maintenance scenarios, enabling easier deployment, more stable operating and more efficient maintenance.3Featuress4Hardware4.1 AppearanceProduct images provided in this file are for reference only, and the actual productsshall prevail.44.2 DimensionsThe board thickness is not greater than 2.0 mm, and the total thickness (board thickness + thickness of components on front and rear panels) is not greater than 17.5 mm.4The u n it of dimension chart is “mm ”. The location holes are connected to signal grounds (GND).4.3 IndicatorsHC 11 12 HD HDCLK 13 14 HLAT HOE 15 16 GNDReceiving Card MRV316Product Description5 Software Structure6 Typical Networking6 Typical NetworkingFigure 6-2 No sending card mode7 Specifications 5Software StructureFirmware in the delivery MRV316 includes MCU program and FPGA program. Program download method:Visit w ww.novastar-led.c n a nd change the user interface language to English at thetop right. Then, on the displayed P roducts&Downloads page, click the target receiving card in the R eceiving Card section to enter its detail introduction page. Atlast, click D ownloads to enter the download list and download the required program packages.6Typical NetworkingThe MRV316 is applied to the LED display synchronous system which is generally composed of the LED display, receiving card, LED display controller and controller peripherals. The receiving card is connected to the LED display over HUB connectors.The synchronous system requires connecting a computer to display the computer ’s images and texts on the LED display. The synchronous system's structure is shown in the following figure. Figure 6-1 Sending card modeReceiving Card MRV316Product Description 9。

产品规格书
接收卡 MRV220-1
本文中的照片仅供参考，请以购买的实物为准
Rev2.1.4 NS110000246
功能特性
MRV220-1是诺瓦M3系列28组数据小接收卡。

具有以下特性：
1)单卡输出RGB数据24组；
2)单卡输出RGB数据28组；
3)单卡输出串行数据64组；
4)单卡带载像素为256×226；
5)支持配置文件回读；
6)支持温度监控；
7)支持网线通讯状态检测；
8)支持供电电压检测；
9)支持逐点亮色度校正；
10)符合欧盟RoHs标准；
11)符合欧盟CE-EMC CLass A标准。

接口定义
控制系统有2种工作模式,每种模式的2个60P输出不同数据，每个60P还可
以分成2个30P，接口定义如下:
1)24组并行数据模式
支持24组RGB并行数据，定义如下：
技术参数
附录
串行译码电路：。

SpecificationsReceiving Card MRV360Product images provided in this file are for reference only , and the actual products shall prevail.Rev2.1.2NS110100109XI 'AN NOVA S TAR T E C H C O .,L T D.OverviewNova M3 MRV360 is one model of Nova receiving card. It has the interface of MOM(Memory On Module).Features1) Single card outputs 16-group of RGBR 'data; 2) Single card outputs 20-group of RGB data;3) Single card outputs 64-group of serial data;4) Supporting MOM management, MOM can store calibrationcoefficient and the LED module information; 5) Single card supports resolution of 256x226； 6) Configuration file readback; 7) Temperature monitoring； 8) Ethernet cable communication status detection; 9) Power supply voltage detection; 10) Pixel-by-pixel brightness and chromaticity calibration.Brightness and chromaticity calibration coefficients for each LED; 11) Pre-store picture setting; 12) Able to connect monitoring card; 13) Comply with EU RoHs standard;14) Comply with EU CE-EMC Class A standard.XI 'A N N O V A S T A R T E C H C O .,L T D.Output Interface DefinitionUnder all the three different working modes of it, two 50P interfaces can output different data, and only one common program and software are required. No customized program is needed. Interfaces are defined as follows:1) 16-group data modeSupporting 16-group of RGBR 'parallel data, defined as follows:Virtual R signal in the last data group of each 50pin hub is decodingsignal E at 1/32 scan mode.X I 'AN NOVA S TAR T E C HCO .,L T D.2) 20-group parallel data modeSupporting 20 sets of parallel data, defined as follows:XI 'A N N O VA S T A R T E C HCO3) 64-group serial data modeSupporting 64 sets of serial data, defined as follows:Under serial mode, there are 64 data cables totally. Each cable can drive one LED bar independently.XI 'A N N O V A S T A R T EIn case of horizontal LED bar, the default is that Data1 drives the first row from the top, and Data64 drives the 64th row. (front view).In case of vertical LED bar, the default is that Data1 drives the first column of from the left, and Data64 drives the 64th column. (front view).Thickness of the board is about 1.6mm. The overall thickness (board thickness＋thickness of the components on front and back side) is about 18.5mm.Unit: mm.X I'A NN OV AS TA RT EC HC O.,L TD.Note: Product images provided in this file are for reference only, and the actual products shall prevail.J4（MOM interface ）defintion ：J9 definition （Indicator light Socket ）J10 definition （Indicator Socket ）：T E C H C OSpecific Model ListTo meet the needs of different customers, Nova has provided more specific models of the products, including standard products in stock. Other models need to be customized.E C H C O .,L T D.Serial data decoding circuit：X I'A NN OV AS TA RT EC HC O.,L TD.。

A8Specifications Document Version:V1.2.0Copyright © 2018 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi’an NovaStar Tech Co., Ltd.Trademarkis a registered trademark of Xi’an NovaStar Tech Co., Ltd.StatementYou are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). This document is intended to help you understand and use the product. For accu racy and reliability, NovaStar may make improvements and/or changes to this document at any time and without notice. Any problem in use or any good suggestion, please contact us through ways provided in the document. We will do our utmost to solve the prob l ems and adopt the suggestions after evaluation as soon as possible.Specifications Change HistoryChange HistorySpecifications ContentsContentsChange History (ii)1 Safety ...............................................................................................................................12 Overview ..........................................................................................................................23Features ...........................................................................................................................43.1 Improvement in DisplayEffect (4)3.2 Improvement inMaintainability (5)3.3 Improvement in HardwareReliability (6)3.4 Improvement in SoftwareReliability (6)4 Hardware (7)4.1 Appearance .................................................................................................................................................. 74.2Dimensions ............................................................................................................................................ (7)4.3 Indicators .......................................................................................................................................... (8)4.4 Definition of Data Interface( Top ) (9)4.1.1 32-Group ParallelData (9)4.1.2 64-Group SerialData ..............................................................................................................................124.1.3 Extended FunctionsDesign (14)5 Firmware Update (16)6 Applications (17)7 Specifications (18)A Abbreviation (19)B Terms (20)1 Safety1 S afetyThis chapter illustrates safety of the A8 receiving card to ensure the product’s storage,transport, installation and use safety. Safety instructions are applicable to allpersonnel who contact or use the product. First of all, pay attention to following points.●Read through the instructions.●Retain all instructions.●Comply with all instructions.Storage and Transport Safety●Pay attention to dust and water prevention.●Avoid long-term direct sunlight.●Do not place the product at a position near fire and heat.●Do not place the product in an area containing explosive materials.●Do not place the product in a strong electromagnetic environment.●Place the product at a stable position to prevent damage or personal injurycaused by dropping.●Save the packing box and materials which will come in handy if you ever have tostore and ship the product. For maximum protection during storage and shipping,repack the product as it was originally packed at the factory.Installation and Use Safety●Only trained professionals may install the product.●Plugging and unplugging operations are prohibited when the power is on.●Ensure safe grounding of the product.●Always wear a wrist band and insulating gloves.●Do not place the product in an area having frequent or strong shake.●Perform dust removing regularly.XI'ANNOVASTARTECHCO., ● Contact NovaStar for maintenance at any time, rather than have the productdisassembled and maintained by non-professionals without authorization.●Replace faulty parts only with the spare parts supplied by NovaStar.2 Overview 2 O verview A8 is a high-end receiving card developed by NovaStar, featuring small size and largeloading capacity with a single card loading up to 512 x 256(PWM IC) pixels.A8 can work with the independent controller MCTRL R5, making display rotate at any angel. A8 can also work with the independent controller MCTRL4K featuring largeloading capacity and support HDR10 compliant video input, realizing larger dynamicbrightness range and larger color space, and making the image smoother.A8 supports pixel level brightness and chroma calibration by working with NovaLCT and NovaCLB to realize calibration on each pixel. It can effectively remove colordifference and greatly improve LED display image consistency, presenting smootherimages to users. In addition, it also supports image rotation in 90° increments,creating richer images and improving visual experiences. Software and hardware designs of the A8 concern the user deployment as well as operating and maintenance scenarios, enabling easier deployment, more stable operating and more efficient maintenance. Advanced hardware design:●The small-size hardware design is applicable to scenarios of small cabinet space and small pixel pitch. ● The used DDR3 connectors have stable contact performance and goodcompatibility. Useful software design: ● Support for HDR10. ●Support for low latency (Supported by dedicated firmware program). ● Support for 18Bit+.●Support for ClearView.●Support for LVDS transmission (Supported by dedicated firmware program).●Support for smart module (Supported by dedicated firmware program).●Support for quick seam correction.●Support for 3D function.●Support for auto module calibration.●Support for Mapping function.●Support for pre-stored image setting of the receiving card.2 Overview●Support for module Flash management.●Supports monitoring voltage and temperature of itself without using otherperipherals.●Support for monitoring of Ethernet cable communication status (Supported bydedicated firmware program).●Support for 5-pin LCD module.●Support for image rotation in 90° increments.Specifications 3 FeaturesReceiving Card A8Specifications 3 Features3.2provement in Hardware ReliabilityReceiving Card A8Specifications 4 Hardware Board thickness is not greater than 1.5 mm, and the total thickness (board thickness+ thickness of both front panel and back panel) is not greater than 6.5 mm.Unit of the dimension chart is “mm”. Ground connection is enabled for location hole(GND). 4Hardware 4.1AppearanceProduct images provided in this file are for reference only, and the actual productsshall prevail.Models of DDR3 connectors (connecting fingers) and receptacle used by A8 areshown in table Table 4-1.Table 4-1 Model of high-density connector4.2Dimensions4.4 Definition of Data Interface ( Top )Note 2. Operating indicator that meets low level is valid.Note 3. OE_RED, OE_GREEN and OE_BLUE are display enabled pins. In case that OE_RGB are not controlled separately, OE_RED is applied. While PWMchip is used, GCLK signal is enabled.Note 4. RFU1–18 are the reserved extended function interfaces. Please refer to “4.4.3 Extended Functions Design”.5 Firmware Update6 Applications7 Specifications6ApplicatioA8 is applied to LED display synchronous system which is generally composedLED display, HUB board, receiving card, video controller and controller peripher The receiving card is connected to the display over a HUB board.Synchronous system requires connecting a computer to display the computer ’ s images and texts on the LED screen. Structure of the synchronous system is as shown in the following figure.5Firmware UpdaStep 1 Visit www.novastar.tech to download the firmware update package and save it t Step 2 Run NovaLCT and choose User > Advanced Synchronous System User Loglog in. Step 3 Type the secret code " admin " to enter the program loading page.Step 4 Click Browse to select the program (the firmware update package you saved onpath and then click U pdate .Step 5 Click Refresh to check current hardware version information.A AbbreviationB Terms A Abbreviati FFPGA Field -P rogrammable Gate ArrayB Terms 18Bit+Specify the grayscale of LED displays. Enabling 18 bit mode on NovaLCT-Mars could improve LED display grayscale by 4 times, and therefore avoid grayscale losscaused by brightness reduction and make images finer.ClearViewDisplay screen effects. Enable ClearView on NovaLCT-Mars to adjust the texture,size and contrast in different area based on human visual system to make imagemore realistic.Calibration coefficientCalibration system generates a group of values for each LED lamp, including information about brightness and chroma. After display calibration, the calibration values of each lamp are just the calibration coefficient.Smart moduleThe smart module is composed of Flash and MCU.Flash could store calibration coefficients and lamp panel information. MCU could communicate with the receiving card to realize monitoring over temperature, voltage and wiring communication status, Working with the driver chip, A8 supports open circuit detection on LED.The smart module could make monitoring unit smaller, requiring no independent monitoring card and saving cabinet space.MappingAfter the Mapping function is enabled on NovaLCT, the target cabinet will display the cabinet number and Ethernet port information, and the user could get the receiving card’s location and wiring route.。

SpecificationsReceiving Card XC100Rev1.2.1NS110100191XI 'AN NOVA S T AR T E C H CO .,LT D.OverviewXC100 is super-small full function high-end mini receiving card rolled out lately by NovaStar. Compared with traditional receiving card, XC100 is more flexible in usage and DDR3 SODIMM port adopted renders it to adapt to various electrical structures easily; as a result, one module card is suitable for all applications, greatly reducing the types of module cards to be purchased.XC100 single card can load pixel of 256*256, supporting such utility functions as intelligent module management, LED display human-computer interaction and built-in voltage temperature detection. Specific circuit and program design of XC100 can effectively reduce electromagnetic radiation of the system, helping users to make their products pass EMC certification easily.Such a powerful XC100 is bound to usher in a new age of receiving card! Features 1) Single card supports pixel points of 256*256.2) Single card supports parallel output of 24-module RGB signal, extending to parallel data of 48-module RGB at maximum.3) Any scanning types within 1-1/32 scan and 595 serial decoding scanning aresupported.4) All mainstream LED driving chip like regular chip and PWM chip are supported. 5) High gray scale and high refresh rate is supported. 6) Pixel-by-pixel calibration of brightness degree is supported.7) Perfect special shape support; Random alignment, random test pixel, special-shapedmodule, special-shaped cabinet and special-shaped LED display make load more easily.8) Seamless switching of various hot backups including loop backup, dual card backup,dual power supply backup, etc. are supported.9) Human-computer interaction of cabinet and LED display is supported. 10) One-way voltage and temperature detection is available.11) Intelligent module is supported, with the functions of storing and managing calibrationcoefficient, module information and moudle parameters, as well as row line detection and LED pixel-by-pixel error detection without the need of monitoring card. 12) Special EMC design effectively reduces electromagnetic radiation.XI 'A N N O VA S T A R T E C H C O .,LT D.AppearanceNotes1: Positioning hole is connected to GND.DimensionsUnit: mmXI 'AN NOVA S T AR T E C H CO .,LT D.Output Interface DefinitionIntelligentmodule portX I'A NN OV AS TA RT EC HC O.,L TD.Gigabit network portX I N OV AS TA RT EC HC O.,L TD.X IX ISpecifications X I T E C。

Taurus SeriesMultimedia PlayersApplication SolutionProduct Version: V1.3.0Document Number:NS120100268X I 'A N N O V A S T A R TE C H C O .,L T D .Copyright © 2018 Xi’an NovaStar Tech Co., Ltd. All Rights Reserved.No part of this document may be copied, reproduced, extracted or transmitted in any form or by any means without the prior written consent of Xi’an Nova Star Tech Co., Ltd.Trademarkis a trademark of Xi’an NovaStar Tech Co., Ltd.StatementYou are welcome to use the product of Xi’an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar). This document is intended to help you understand and use the product. For accuracy and reliability, NovaStar may make improvements and/or changes to this document at any time and without notice. If you experience any problems in use or have any suggestions, please contact us via contact info given in document. We will do our best to solve any issues, as well as evaluate and implement any suggestions.X I'A NN OV AS TA RT EC HC O.,L TD.Application Solution Table of ContentsTable of ContentsTable of Contents (ii)1 Overview (1)1.1 About This Solution (1)1.2 Characteristics of the Application Solution (1)1.2.1 Synchronous Playing (1)1.2.2 Smart Brightness Adjustment ................................................................................................................... 2 1.2.3 4G Module ................................................................................................................................................ 2 1.2.4 Cluster Management ................................................................................................................................ 3 1.3 Software Acquiring Method ......................................................................................................................... 3 2 AD Player and Mirror Screen Solution ..................................................................................... 5 2.1 Overview ...................................................................................................................................................... 5 2.2 Single Application ........................................................................................................................................ 7 2.2.1 Networking Diagram ................................................................................................................................. 7 2.2.2 Required Software .................................................................................................................................... 7 2.2.3 Relevant Configurations ........................................................................................................................... 7 2.3 Cluster Application ....................................................................................................................................... 8 2.3.1 Networking Diagram ................................................................................................................................. 8 2.3.2 Required Software .................................................................................................................................... 8 2.3.3 Required Hardware Devices (8)2.3.4 Relevant Configurations (9)2.4 Splicing (12)2.4.1 Networking Diagram (12)2.4.2 Required Software (13)2.4.3 Relevant Configuration ........................................................................................................................... 13 3 Post Screen Solution . (16)3.1 Overview (16)3.2 Networking Diagram (18)3.3 Required Software (18)3.4 Required Hardware Devices (18)3.5 Relevant Configuration .............................................................................................................................. 19 X I 'A N N O V A S T A R T E C H C O .,L T D.Application Solution Table of Contents4 General Operations (23)4.1 Taurus Login upon ViPlex Handy (Android and iOS) (23)4.2 Taurus Login upon ViPlex Express (Windows) (24)X I'A NN OV AS TA RT EC HC O.,L TD.Application Solution 1 Overview1 Overview1.1 About This Solution Taurus series products are the second-generation multimedia players developed by NovaStar specially designed for the medium-small size LED full color displays, and applicable to all kinds of display devices as well as many application scenes.AD player, mirror screen and post screen are used here as examples to describe the application solution of Taurus series products. Pictures of Taurus series products used in networking diagram are taken from T6 model.For more information of Taurus series products, please visit www.novastar.tech to download relevant documents.1.2 Characteristics of the Application Solution 1.2.1 Synchronous Playing This function makes several displays play the same image at the same time with high accuracy based on advanced synchronous playing and scheduling technologies. The synchronous playing function could be enabled for different displays as long as following three requirements are met: ● The synchronous playing function has been enabled on the ViPlex or VNNOX. ●The time of multiple Taurus products are synchronized. ● Playing plans of multiple T aurus products are the same without random transitionor media.Advantages of the synchronous playing function are shown in Table 1-1.Table 1-1 Synchronous playingTime could be synchronized through NTP and RF modes from which the user could select one as required:X I 'A N N O V A S T A R T E C H C O .,L T D .● NTP time synchronization: Taurus time synchronization is based on NTP server.No hardware is required to be added, and time synchronization accuracydepends on network speed. Consequently, network traffic will be consumed by using 4G network.●RF time synchronization: Master and slave devices are required to be set for Taurus. Time of the slave device is synchronized with that of the master device through RF network, and therefore RF device is required. This timesynchronization method is applicable to events with high time synchronization requirement and does not consume network traffic, but its signal receivingdepends on the environment and is limited by distance. 1.2.2 Smart Brightness AdjustmentSmart brightness adjustment includes auto brightness adjustment and timing brightness adjustment.●Auto brightness adjustment: Display brightness will automatically adjust according to environment brightness.● Timing brightness adjustment: Display brightness will automatically adjust to a specific value at a given point of time. Taurus products have brightness sensor connectors. Connect the light sensor and set smart brightness adjustment rules on ViPlex to enable the smart brightness adjustment function. Advantages of smart brightness adjustment are as shown in Table 1-2. Table 1-2 Smart brightness adjustmentTaurus products support manual brightness adjustment as well. 1.2.3 4G Module 4G module can be installed on the Taurus series products. To connect the Taurus to the Internet via 4G network, buy the corresponding 4G module and install it according to the country or region of the service provider.The Taurus can be connected to the Internet through the following three methods listed from the highest to the lowest priority:●Wired network ●Wi-Fi Sta ● 4G networkWhen the three methods are all enabled, the Taurus will select signals automatically according to the priorities.T E C H C O .,L T D .When mobile data network is enabled on ViPlex and priority requirements for signal selection are met, Taurus products with 4G module could connect to Internet. Advantages of 4G module are as shown in Table 1-3.Table 1-3 4G module1.2.4 Cluster ManagementDisplay quantity increases fast following with the development of smart city and commercial application, and cluster solution of NovaStar emerges to uniformly manage and monitor numerous displays in different places.●VNNOX: A cloud publishing service used to realize display remote content management and remote terminal control. ● NovaiCare: A cloud monitoring service used to realize display remote monitoring. VNNOX and NovaiCare could be accessed to remotely and uniformly manage displays with PC, Pad or mobile phone as long as Internet is available. Advantages of cluster management are as shown in Table 1-4. Table 1-4 Cluster management1.3 Software Acquiring MethodTable 1-5 Software acquiring methodsA S T A R T E C H C O .,L T D .X I'A NN OV AS TA RT EC HApplication Solution 2 AD Player and Mirror Screen Solution2AD Player and Mirror Screen Solution2.1 Overview AD player and mirror screen, the typical commercial display applications, are mainly used for information publishing and advertisement display, and can be placed at the shopping mall, hotel, office building, exhibition, bank, station and community. There are two application modes for the mirror screen which is a mirror when the display is turned off. There are many application modes for the AD player and mirror screen, and only typical applications are introduced in this chapter, including the single application, cluster application and splicing application. Characteristics of the AD player and mirror screen of NovaStar are as shown in Table 2-1. Table 2-1 AD player and mirror screenT A R T E C H C O .,L T D.Application Solution 2 AD Player and Mirror Screen SolutionX I'A NN OV AS TA RT EC HC O.,L TD.2.2 Single Application2.2.1 Networking DiagramTaurus products provide Wi-Fi AP itself. After connecting to Wi-Fi AP with PC, Pad and mobile phone, enter the username and password to log in to the Taurus. 2.2.2 Required Software ● ViPlex Handy●ViPlex Express 2.2.3 Relevant Configurations No need to set. Refer to 4 General Operations for specific operations to connect and log in to the Taurus products. XI 'A N N O V A S T A R T E C HCO .,L T D.2.3 Cluster Application2.3.1 Networking DiagramVNNOX and NovaiCare could be accessed directly or by way of bridge connection. When bridge connection is selected, following three methods for Internet connection of Taurus products are available with priorities ranging from high to low: ● Wired network ● Wi-Fi Sta● 4G network When the three methods are all enabled, Taurus products will select signals automatically according to the priorities. 2.3.2 Required Software ● ViPlex Handy ● ViPlex Express ● VNNOX ●NovaiCare2.3.3 Required Hardware DevicesXI 'A N N O V A S T A R T E C HCO .,L T D.2.3.4 Relevant ConfigurationsBefore You Begin● The login username and password for VNNOX, NovaiCare and NovaLCT are acquired.● Create solution(s) on VNNOX without random transition and random media of the solution(s).● Create asynchronous players on VNNOX and associate the players with the License.●Configurations required before monitoring have been done on NovaLCT and NovaiCare.Refer to software online help for specific operations of VNNOX, NovaiCare and NovaLCT.Acquiring Player Authentication InformationThe authentication information is required when you bind asynchronous players on VNNOX to the Taurus through ViPlex.Step 1 Visit and log in to VNNOX Lite or VNNOX Pro .Step 2 Perform the following operations to view the correct authentication information.● VNNOX Lite: Choose > Account . ●VNNOX Pro: Choose > Organization Management > System Management and select the Player Authentication tab.Configuring ViPlex Handy (Android and iOS) Step 1 Log in to the Taurus. Refer to 4.1 Taurus Login upon ViPlex Handy (Android and iOS). Step 2 Click screen name to enter Screen management page. Step 3 Set rules for smart brightness adjustment. 1. Select Screen Settings > Brightness Control . 2. Click Brightness Mode, select Smart , and click OK . 3. Click Smart Brightness Adjustment Parameters . 4. Click Edit . 5. Click to set rules for timed brightness adjustment. Then click OK . 6. Clickto set rules for auto brightness adjustment. Then click OK .7. Click Auto adjustment parameters to set the corresponding relation between ambient brightness and screen brightness. 8. Click OK .Step 4 Set the connection method between the Internet and Taurus.Priorities of wired network, Wi-Fi Sta and 4G network range from high to low. When the three methods are all enabled, the Taurus will select signals automatically according to the priorities.XI'A NN O VA S T A R T E C HCO .,L T D.●Wired network: When static IP address is required, select Network Settings > Wired Network Setting , turn DHCP off, enter the static IP address of the Taurus, and click OK .● Wi-Fi Sta: Select Network Settings > Wi-Fi Setting , and turn WiFi on. Click the Wi-Fi name of the external router and enter the Wi-Fi password, and click OK . ●4G network: Select Network Settings > Mobile Data Setting , and turn Mobile Data on.Step 5 Bind the asynchronous player.1. Select Remote Management > VNNOX .2. Set the VNNOX server and player authentication information.3. Click Obtain and select a player from the drop-down box of Player .4. Click OK after setting.Step 6 If display remote monitoring is required, perform the following procedures. Otherwise,ignore this step.1. Select Remote Management > NovaiCare .2. Turn NovaiCare on.3. Select the service node of the NovaiCare from the drop-down box of Server .4. Click the right side of Possessor line.5. Enter the username for login NovaiCare in the pop-up dialog box, and click OK .6. Click OK after setting.Step 7 Repeat above steps to configure other Taurus products in cluster till all Taurus products have been configured. Configuring ViPlex Express (Windows)Step 1 Log in Taurus and see detailed operations in 4.2 Taurus Login upon ViPlex Express (Windows).Step 2 Select Screen Control. Step 3 Set rules for smart brightness adjustment. 1. Select Brightness adjustment . 2. Select the target terminal in the terminal list.3. Clickon the Smart page.4. Set rules for timed brightness adjustment and click Add .5. Set rules for auto brightness adjustment and click Add .6. Click Cancel .7. Click Apply .Step 4 Set the way to connect Taurus to the Internet.The priority of wired network, Wi-Fi Sta and 4G network is from high to low. If all of thethree ways are enabled, the Taurus will choose signal automatically according to the priority order.1. Select Network configuration .XI 'A N N O V A S T A R T E C HCO .,L T D.2. Select the target terminal in the terminal list and perform the following operationsaccording to actual needs.−Wired network: If it is required to set static IP address, deselect Dynamic DHCP , enter the IP address information of the Taurus and then click Apply in the Wired network configuration section.− Wi-Fi Sta: Turn on Wi-Fi in the Wi-Fi configuration section. Click the Wi-Fi name of external router and then enter Wi-Fi password and click OK . −4G network: In the Mobile network configuration area, turn on mobile network.Step 5 Bind asynchronous players.1. Select Server configuration .2. Select the target terminal in the terminal list.3. In Configure parameters for connecting screens to VNNOX , configureVNNOX server and player authentication information. 4. Clicknext to Player and select a player.5. Click Bind .Step 6 If you want to monitor displays remotely, please perform this step; otherwise, skip thisstep.1. In Configure parameters for connecting screens to NovaiCare , configure NovaiCare server and login user name.2. Click Send . Step 7 Repeat above steps until all the Taurus products in the cluster are configured. Configuring VNNOXWhen setting timing rules and synchronous playing upon ViPlex, every Taurus product is required to be set individually, and batch setting is available for setting timing rules and synchronous playing upon VNNOX. When the public network isavailable, VNNOX is recommended for batch configuration to reduce manual operations. Step 1 Visit and log in to VNNOX Pro.Step 2 Set time synchronization rule.1. Select> Players Management > Time Synchronization .2. Click NTP server configuration.3. Configure NTP service information, and then click Save&Close .4. Click New on the page of time synchronization task list.5. Enter time synchronization task name and select time synchronization method,and then click Next .− NTP: Select a NTP server and then click OK .−RF: Select a time synchronization standard device and then click OK . 6. Click Add in the Players tab of the time synchronization task attribute page.−NTP time synchronization: Select all the players in cluster and then click OK .X I 'A N N O V A S T A R T E C HCO .,L T D.−RF time synchronization: Select all the slave players in RF network and then click OK .7. When the time synchronization method upon RF network is selected, and NTPserver is used for the time synchronization standard device, click Configure tab to set NTP to Yes , and select NTP server. Otherwise, ignore this step. 8. Click Save or Save&Close . Players added in the time synchronization task willperform time synchronization according to rules defined in the task.Step 3 If the same image is required to be played by different screens, perform the followingprocedures. Otherwise, ignore this step.1. Select> Players Management > Players .2. Select asynchronous players corresponding to all Taurus series productsrequiring enabling the synchronous playing function. 3. Click Real-time control and select Turn on sync play from the drop-down box.Step 4 Associate with solution(s).1. Select> Players Management > Players .2. Select a player and click Attribute , or click a player name.3. Select a solution from the drop-down box of parameter associate solution .4. Whether solution distribution type is Manual.− Yes. Click Save&Close to return to the player list page. Perform term 5. −No. Click Save or Save&Close . VNNOX will automatically distribute solutions to corresponding Taurus products.5. Select the target player, and click Update solution to manually distributesolutions to corresponding Taurus products. 6. Repeat above steps to associate with solutions for other players in cluster till all players have been configured. 2.4 Splicing 2.4.1 Networking DiagramThe following figure uses three displays splicing as an example to illustrate Taurus connection.X I 'A NNO VA S T A R T E C HCO .,L T D.The Taurus product provides Wi-Fi AP itself. Connect to Wi-Fi AP of each Taurus product through PC, Pad and mobile phone, and then enter the username and password to log in to the Taurus.2.4.2 Required Software● ViPlex Handy●ViPlex Express2.4.3 Relevant Configuration2.4.3.1 Configuring the first display Configuring ViPlex Handy (Android and iOS)Step 1 Log in to the Taurus of the first display. Refer to 4.1 Taurus Login upon ViPlex Handy(Android and iOS) for specific operations. Step 2 Click screen name to enter the Screen management page. Step 3 Select Video Control. Step 4 Click Edit .Step 5 Configure the required parameters.● Mode : Manual ● Source : Inside ● Offset X : 0 ●Offset Y : 0XI 'A N NOVA S TA R T E C HCO .,L T D.Step 6 Click OK .Configuring ViPlex Express (Windows)Step 1 Log in Taurus and see detailed operations in 4.2 Taurus Login upon ViPlex Express(Windows). Step 2 Select Video source.Step 3 Select the target terminal in the terminal list.Step 4 On the Manual page, configure all required parameters.● Video source type : Internal ● X : 0 ●Y : 0Step 5 Click Apply .2.4.3.2 Configuring other displaysConfiguring ViPlex Handy (Android and iOS)Step 1 Log in to the Taurus of the second display. Refer to 4.1 Taurus Login upon ViPlexHandy (Android and iOS) for specific operations. Step 2 Click screen name to enter Screen management page. Step 3 Select Video Control. Step 4 Click Edit .Step 5 Configure the required parameters.Horizontal splicing image is taken as an example here for illustration. In the event of vertical splicing, the way for setting Offset Y is the same as that for setting Offset X .● Mode : Manual ● Source : HDMI●Offset X: (The display serial number – 1) x The Image width . For example, when the image width is 500px, it is required to be set as 500px for the second display and 1000px for the third display. ●Offset Y : 0Step 6 Click OK .Step 7 Repeat above steps to configure other Taurus products till all Taurus products havebeen configured.Configuring ViPlex Express (Windows)Step 1 Log in Taurus and see detailed operations in 4.2 Taurus Login upon ViPlex Express(Windows). Step 2 Select Video source.Step 3 Select the target terminal in the terminal list.XI 'AN NOVA S TAR T E C HCO .,L T D.Step 4 On the Manual page, configure all required parameters.Horizontal splicing image is taken as an example here for illustration. In the event ofvertical splicing, the way for setting Y is the same as that for setting X.●Video source type: HDMI●X: (The display serial number– 1) x The Image width. For example, when theimage width is 500px, it is required to be set as 500px for the second display and1000px for the third display.●Y: 0Step 5 Click Apply.Step 6 Repeat above steps to configure other Taurus products till all Taurus products have been configured.X I'A NN OV AS TA RT EC HC O.,L TD.Application Solution3 Post Screen Solution3Post Screen Solution3.1 OverviewPost screens prevail on both sides of highways and roads following with thedevelopment of the smart city. Smart post screen has distinct advantages compared with the conventional post which features illumination and static advertisement only and requires new manufacture and installation in case of advertisement replacement, while the smart post provides functions including illumination, security monitoring, environment monitoring, emergency call, charging pile and LED display which used high-definition smart LED post screen for road leading, data release and advertising promotion.Post screens can be used without quantity limits, and the display contents can be controlled individually or in batch based on cluster management method. Characteristics of the post screen of NovaStar are as shown in Table 3-1. Table 3-1 Post screenR T E C H C O .,L T D.N O V A S TX I' A N3.2 Networking DiagramVNNOX and NovaiCare could be accessed directly or by way of bridge connection to centrally manage post screens.Taurus products can connect to Internet through the wired network, Wi-Fi and 4G network which is recommended for this solution.3.3 Required Software● ViPlex Handy● ViPlex Express● VNNOX●NovaiCare 3.4 Required Hardware DevicesXI 'A N NOVA S TAR T E C HCO .,L T D.3.5 Relevant ConfigurationBefore You Begin● Acquire the login username and password of VNNOX, NovaiCare and NovaLCT. ● Create a solution on the VNNOX without random transition and random media. ● Create an asynchronous player which associates with License on the VNNOX. ●Complete configurations required to be done before monitor on NovaLCT and NovaiCare.Refer to software online help for specific operations of VNNOX, NovaiCare and NovaLCT.Acquiring player Authentication InformationThe authentication information is required when you bind asynchronous players on VNNOX to the Taurus through ViPlex.Step 1 Visit and log in to VNNOX Lite or VNNOX Pro.Step 2 Perform the following operations to view the correct authentication information.●VNNOX Lite: Choose > Account .●VNNOX Pro: Choose > Organization Management > SystemManagement and select the Player Authentication tab.Configuring ViPlex Handy (Android and iOS) Step 1 Log in to the Taurus. Refer to 4.1 Taurus Login upon ViPlex Handy (Android and iOS) for specific operations. Step 2 Click the screen name to enter the Screen management page. Step 3 Set rules for smart brightness adjustment. 1. Select Screen Settings > Brightness Control . 2. Click Brightness Mode to select Smart , and then click OK .3. Click Smart Brightness Adjustment Parameters .4. Click Edit .5. Click to set rules for timed brightness adjustment. Then click OK .6. Clickto set rules for auto brightness adjustment. Then click OK .7. Click Auto adjustment parameters to set the corresponding relation betweenambient brightness and screen brightness. Then click OK . 8. Click OK .Step 4 Set Internet connection mode for the Taurus.1. Select Network Settings > Mobile Data Setting .2. Turn Mobile Data on.Step 5 Bind the asynchronous player.1. Select Remote Management > VNNOX .X I 'A N N OV A S T A R T E C HCO .,L T D.2. Set the VNNOX server and player authentication information.3. Click Obtain and select a player from the dropdown box of Player .4. Click OK after setting.Step 6 If display remote monitoring is required, perform the following procedures. Otherwise,ignore this step.1. Select Remote Management > NovaiCare .2. Turn NovaiCare on.3. Select the service node of NovaiCare from the dropdown box of Server .4. Click the right side of Possessor line.5. Enter the login username of NovaiCare in the pop-up dialog box, and click OK .6. Click OK after setting.Step 7 Repeat above steps to configure other Taurus products in cluster till all Taurusproducts have been configured.Configuring ViPlex Express (Windows)Step 1 Log in Taurus and see detailed operations in 4.2 Taurus Login upon ViPlex Express(Windows).Step 2 Select Screen Control. Step 3 Set rules for smart brightness adjustment. 1. Select Brightness adjustment . 2. Select the target terminal in the terminal list.3. Click on the Smart page.4. Set rules for timed brightness adjustment and click Add .5. Set rules for auto brightness adjustment and click Add .6. Click Cancel .7. Click Apply . Step 4 Set the way to connect Taurus to the Internet. 1. Select Network configuration .2. Select the target terminal in the terminal list.3. In the Mobile network configuration area, turn on mobile network.Step 5 Bind asynchronous players.1. Select Server configuration .2. Select the target terminal in the terminal list.3. In Configure parameters for connecting screens to VNNOX , configureVNNOX server and player authentication information. 4. Clicknext to Player and select a player.5. Click Bind .Step 6 If you want to monitor displays remotely, please perform this step; otherwise, skip thisstep.XI 'A N N O V A S T A R T E C H C O .,L T D.。