下载文档原格式
振动电机里面激振动的调整步骤及维护保养
振动电机里有很多知识想必大家都知道了，但是振动电机里有一个关键但微小的步骤却有很多人都不知道，下面就为您介绍一下吧要特别注意，调整激振力时，要将振动电机两端出轴上的可调偏心块向同一个方向调整为相同的角度。
一、激振力的调整步骤：
1. 拆除防护罩。
2. 旋松外侧偏心块加紧螺栓。
3. 两侧偏心块应同方向转动，使轴上刻线对准偏心块上激振力示值线至需要的激振力值处，并检查两端是否为相同的角度。
二、使用维护，保养与存放：
1、定期补充油脂，一般2-3个月补油一次
2、振动电机一般运行4-6个月小修一次，一年大修一次。
3、振动电机在运转中如发现有异常响声时，应立即停机检查排除故障后方可再启动运转。
以上就是振动电机里面激振动的调整步骤及维护保养。
◆ 尊敬的用户：感谢您选用我公司的产品。
您在使用本产品以前，请详细阅读本使用说明书，并严格按照使用说明书进行操作。
如有不明之处，需及时与我公司联系，谨防操作中出现意外事故。
◆ 型号说明*本公司交流振动电机产品以下列符号表示： MVE 激振力（kg）/ 转速 特殊符号3000转/分 300kg 3000转/分 300kg 工作电压 12V表示直流工作电源 表示激振力为200kg表示振动电机◆ 振动电机的使用条件1、环境温度随季节而变化，但一般不应超过 -20℃~+40℃。
2、海拔：不超过1000米。
3、频率：50 Hz（也可按用户特殊要求设计制造，注意铭牌标征数据应和电源对应）。
4、额定电压：电机功率＜4KW 时为220 / 380V，即“△”/ “Y”接法，出厂时按380V，“Y”接法；电机功率≥4KW 时为380/660V。
即“△”/“Y”接法，出厂时按380V，“△”接法。
（也可按用户特殊要求设计制造，注意电源电压应和铭牌或接线图中的接线方法相对应）5、绝缘等级：主体 H 级，接线腔 F 级。
0904 振动电机型号说明 1 振动电机的使用条件6、防护等级：IP65。
7、工作方式：S1（连续）。
◆ 贮存与运输1、本公司生产的振动电机SIZE10~60均采用塑料袋及外加纸箱包装，SIZE70~90采用塑料袋及外加木箱包装，建议用户在贮存过程中不要拆开包装物，确保贮存环境干燥通风，避免环境温度急剧变化。
2、贮存和运输过程中，振动电机不可倒置。
重要说明：振动电机在运输过程中造成的损坏应及时与运输公司确认，并将信息反馈至我公司，以便我公司与运输公司交涉。
◆ 振动电机的安装警告！在安装振动电机前，应切断和锁定供给设备的所有能源，并给出警告标志。
1、安装前应检查运输中是否碰伤或受潮、紧固件有无松动等现象。
2、检查铭牌数据是否符合要求，在用户没有特殊要求的情况下，本公司出品的振动电机的偏心块位置均处于铭牌标征的最大激振力位置。
AVITEQ振动电机是一个三相交流感应电机，砝码片在转动轴顶端偏心安装，也称为偏心砝码块（偏心轮），转动时产生离心力。
离心力的数值可以在电机停止时通过调整偏心轮而产生变化。
电机产生的离心力移动工作设备（输送槽、台及其它形式），从而通过振动方式输送物料。
设备造型：AVITEQ产生离心力的值，运行频率和与振动电机相连接的工作设备的质量决定了振幅的大小。
从振动电机传到工作设备的力能通过在对应频率下的加速度值和振幅容易地计算出来。
您能在我们的参考册中，按照有效重量读到所有AVITEQ电机的振幅值。
通过这个办法，您可以迅速找到最合适的驱动器。
振幅决定了物料的最大反射高度，进而在理论上得出可能的输送速度，实际输送速度本质上会受到输送的截面积和被处理物料的密度和输送性能的影响。
AVITEQ振动电机、AVITEQ电磁振动器工作力矩从0.1kg.cm到2763kg.cm，离心力最大可达119KN。
AVITEQ的振动电机能驱动静载超过11,000Kg的设备。
AVITEQ振幅Sn在实际应用中是受到限制的，从一方面讲，受限于工作设备在寿命期中所能承受的加速度，另一方面，当加速度过小时，会产生物料停顿工作设备的结构：AVITEQ电机必须安装在抗弯曲的驱动部位，否则会导致电机不能自动同步，并引起设备断裂的危险。
不正确的电机转向将会给工作设备带来巨大的损害，即使这个时间段非常短。
在大型的，长距离输送装置中一般采用一个横向振动监测，同时也能指示错误转向。
如果在低的重量下得到最大的刚度振动设备就正确地建立了。
如果采用合适的加强筋提供加固，低重量和大刚性强度并非不一致。
磁力振动器AVITEQ磁力振动器作为驱动器设备适用于振动输送槽和输送管、振动筛、除水设备、螺旋输送器和振动台。
AVITEQ作为冲击振动器适用于筒仓、料仓、偏转格栅、下落管、滑槽、筛网和填料厂。
它们可以提供平稳的物流。
在料仓沉降、排放、筛分、除尘或保护过滤、或是大量物料的提取、或在工艺中的特殊任务，如：粗模锻、计量、给料、冷却、加热和干燥中，AVITEQ磁力振动器依赖我们在所有领域中长期积累的振动输送技术方面的宝贵经验，能在每种工况下为您提供可靠的工作状态。
AVW1 and AVW4Vibrating Wire InterfacesFor monitoring of vibrating wire strain gauges withCampbell Scientific dataloggersBackgroundVibrating wire (or vibrating strip)transducers are commonly used to measure strain, load, pressure and water level. These sensors output a frequency signal generated by a vibrating filament that can be read on any CR510, CR10(X), CR23X,CR800 series, CR1000, CR3000 or CR5000 analogue channel.Because frequencies rather than voltage levels are measured, these transducers are often better suited than 4- or 6-wire resistive bridge transducers for applications in elec-trically noisy environments or those requiring long lead lengths.Vibrating wire transducers also have a reputation for long-term stability.Two measurements are usually made; the first is the frequency of the vibrating wire and the second isan optional temperature measure-ment that allows compensation of the frequency measurement.DescriptionThe AVW1 and AVW4 are used to interface vibrating wire strain gauge sensors to compatible CampbellScientific dataloggers. The AVW1interfaces one sensor (temperature and pressure) to two single-ended datalogger channels. The AVW4interfaces four sensors to eight single-ended channels (not avail-able on the CR510).Power ConsumptionFor Geokon sensors, the current drain during the very short (2.4ms)temperature measurement is 0.4mA or less. The current drain during the vibrating wire measure-ment (170ms to 500ms) is 32mA.There is no quiescent current drain.Some vibrating wire sensors with short leads can be monitored without the AVW1or AVW4. However, the AVW1 and AVW4provide important signal conditioning that has the following functions:plete the thermistor bridge for themeasurement of the sensor’s tempera-ture.2.Convert the swept frequency excitationfrom 2.5V (peak-to-peak) to 5V/12V (peak-to-peak), thus ‘plucking’ the wire harder than the maximum 2.5V switchedexcitation. The result is a larger magni-tude signal for a longer time.NOTE: Sensors which need 5V excitation rather then 12V can also be used with the AVW1 and AVW4.3.Provide transformer isolation to strip offany DC noise on the signal. This improves the ability to detect cycles.4.Provide additional transient protectionfor both the temperature and vibrating wire circuits.Although originally designed specifically for the Geokon 4500 series, the AVW1 and AVW4 have also been used very success-fully with other strain gauge models made by Gauge Technique, Roctest, Slope Indi-cator (VWP series) and Geokon. These manufacturers can provide coefficients for monitoring the output of their sensors with Campbell Scientific systems.An increase in pressure on the diaphragm decreases the tension on the wire attached to the diaphragm. A decrease in the wire tension de-creases the resonant frequency in the same way that loosening a string on a guitar decreases its frequency. Therefore, the resonant frequency of the vibrating wire sensor decreases with increas-ing pressure.The Vibrating Wire Measurement Instruction in the datalogger excites the ‘plucking’ and ‘pickup’coils shown in the diagram with a ‘swept’ fre-quency. The datalogger takes 150ms to sweep through all the frequencies. This swept frequency causes the wire to vibrate at each of the individual frequencies. Ideally, all the frequencies except the one matching the resonant frequency of the wire die out in a very short time. The wire vibrates with the resonant frequency for a relatively longtime, and as it does so it cuts the lines of flux inFrequency MeasurementSweep Frequency Range: 100 – 9900Hz (Optimum performance range >1000Hz)Other specifications depend on datalogger model – see specifications (Period Averaging Measurement) in the datalogger brochure or manual.Although the design of the interface coupling transformer means that optimum performance is achieved at frequencies of 1000Hz or more,sensors which operate at frequencies significantly below this can be used successfully with the AVW1 and AVW4. The actual performance of a given sensor will depend on the response of that sensor to the changing drive waveforms and also on the signal level it returns.See Technical Note 23, available on request,which gives more information on the performance of sensors which operate at frequencies below 1000Hz.Measurement Time: The time required to make one repetition of the vibrating wire measurement is given below:150ms to sweep the frequency +20ms delay+(1.5 cycles + no. of cycles measured) * period of signal in mse.g. 671.5ms for a sensor generating a 1000Hz signal measured for 500 cycles.Need help configuring your system? Call ourengineers for assistance.Diaphragm FilterPlucking andPickup Coils4-Conductor CableStainless Steel Housing Vibrating WireTypical Vibrating Wire SensorNo. of Cycles to Average Time Constant of Resonance: Software programmable from 1 to 9999Reference Accuracy: ±(0.01% of reading + Resolution)Resolution: 60ns divided by the number of cycles measured. Resolution is reduced by signal noise and for signals with a slow transition through the zero voltage threshold.Input Sensitivity for Period Measurement:Depends on datalogger model; see separate datalogger brochures.Temperature MeasurementThermistor Bridge: Optimised for YSI44005/Fenwall 192-302 thermistors. Other temperature sensors can be accommodated by direct connection to datalogger.Multiplexing (not CR510)When used with AM16/32B Analogue Multiplexers one AVW1 can monitor 16 strain gauges plus thermistors, or 32 gauges without thermistors.Several multiplexers can be connected to one AVW1.PhysicalOperating Temperature Range: -25°C to +50°C Size/Weight:AVW1 65 x 65 x 30mm, 0.14kg AVW4 170 x 75 x 30mm, 0.41kgthe ‘plucking’ and ‘pickup’ coils inducing the samefrequency on the leads to the datalogger.After waiting for the non-resonant frequencies to die out (20ms) the datalogger accurately meas-ures how much time it takes to receive a user-specified number of cycles. Knowing the time and the number of cycles, the datalogger then computes the square of the frequency (= 1/T 2 where T is the period in milliseconds).InternalBulkhead Seal。
气动振动器的安装及使用说明气动振动器是一种常用的工业设备，用于在各种领域中实现物料输送、筛分和振动搅拌等工作。
它通过利用气压的控制和转换来产生振动力，以此驱动设备进行工作。
在本文中，我们将介绍气动振动器的安装和使用说明，以帮助您正确使用这一设备。
一、安装气动振动器1. 振动器选择：根据您的实际需求选择适合的气动振动器。
考虑到应用领域、设备类型和所需功能，选择合适的型号和规格。
您可以参考振动器的技术规格手册或咨询专业人员，以便做出明智的选择。
2. 安装位置：将振动器安装在合适的位置上。
振动器应连接到所需的设备或结构上，并确保其牢固稳定。
根据振动器的使用要求，可以选择不同的安装方式，如垂直安装、水平安装或倾斜安装。
3. 连接管路：使用适当的管路连接振动器和压缩空气源。
确保管道连接牢固，无漏气，并符合所需的空气流量和压力要求。
建议使用耐压、耐磨的气管，并注意避免管道过长和过多的弯曲，以避免能量损失和压力下降。
4. 气源准备：确保为振动器提供稳定的干燥压缩空气。
在接入振动器之前，务必使用过滤器和调压阀来净化和调节压缩空气，以保护振动器内部的元件，并确保正常运行。
二、使用气动振动器1. 启动和停止：在确保振动器安装正确且连接可靠的情况下，打开气源阀门，使空气进入振动器内部。
振动器将开始工作，并产生振动力。
当振动工作完成时，关闭气源阀门，振动器将停止工作。
注意，在启动和停止振动器时要谨慎操作，以避免意外发生。
2. 振动频率调节：根据需要，可以调节振动器的频率。
通过调整气源阀门的开度，控制气压大小，从而改变振动器的工作频率。
根据实际应用情况，可以选择合适的振动频率来满足工艺要求。
3. 维护保养：定期检查和维护振动器，以确保其性能和使用寿命。
清洁振动器表面及连接部位，检查管路是否有损坏或漏气现象。
如果发现任何问题，请及时修复或更换相关部件。
三、总结与回顾在本文中，我们对气动振动器的安装和使用进行了详细说明。
我们强调了正确选择适合的振动器型号和规格的重要性。
电磁振动器电磁振动器可以用非常灵活。
磁振动器的优点相匹配的振动机的所有设计。
在振动供料器的技术和在所有工业应用的几乎每一种情况下的磁振动器的喜爱系统，特别是如果它取决于高剂量的精度。
应用实例：∙邦克提取∙脱水∙分类∙除尘∙筛查∙输送小和高量的散状物料∙压实∙加药∙载入中∙冷却∙加热干燥作为冲击振动器它们提供了一个平滑的材料流动：∙筒仓∙沙坑∙偏转烤架∙落水管和滑槽∙过滤器和灌装设备AViTEQ`s电磁振动器做一个可靠的工作无处不在。
从我们的经验中受益始于1939年与振动送料技术在任何行业。
在AVITEQ磁力振动器的优点∙在连续工作操作安全∙高水平的具有紧凑的尺寸的性能∙无磨损，无转动部件∙效率∙最新的先进设备，先进的生产工程∙符合所有EC指引，从而影响驱动器∙也可用于有爆炸危险的场所（防爆）∙适用于60 Hz的动力系统和其他电源电压∙运行状态时容易和线性调整∙立即启动/停止切换后∙线性幅度∙可靠的永久使用∙温度开关可选∙特殊的版本可能磁振动器为适合作为用于振动输送的管道和管道，振动过滤器，水去除设备，蜗杆输送机和振动台上的驱动器。
无论是在沙坑结算，排水，筛选，除尘或保护滤镜的情况下，是否有开采大批量或在案件过程工程中的特殊任务，如如堵，计量，送料，冷却，气候变暖和干燥，AVITEQ电磁振动器可靠地执行在任何情况下他们的工作。
使用我们的振动输送技术在各行业的长期经验。
磁振动器弹簧- 质量系统，它总是利用整个振动系统（驱动器和作业装置）的贴近谐振条件。
该驱动器包括用于产生振动的元件，诸如电磁铁和板簧包。
通过在驱动侧的激励电流所产生的振动被直接传送到工作装置（例如，过滤器，导管或管道）。
生成的工作装置的导演，直线振动运动。
在这种情况下的振动方向总是运行在预先确定的“振动角度”到水平。
的“振幅”相当于在这种情况下，对整个系统的双幅。
电磁振动器连续使用可控的驱动电压。
他们立即实现全面输送能力，从而从助跑干扰效应和破败电机驱动器省去了。
INDUSTRIALVIBRATORSTHE WORLDWIDE LEADER IN VIBRATION TECHNOLOGYIntroMVE Standard RangeMVE-Exe Increased SafetyMVE-Exd Explosion-ProofMVE-Milling Grain ProcessingMVE-SV Screen VibratorMVE-SS Stainless SteelInstallation Technical drawingsCompany profile 4Technical features6Standard specifications7The OLI vibrator range 8Certifications 9How to choose a motovibrator10Standard rated voltages 11Optionals 112 poles 124 poles 146 poles 168 poles 182 poles single-phase20MVE-MICRO 22MVE-DC Direct Current 242 poles 264 poles 286 poles 308 poles 322 and 4 poles 346 and 8 poles 366, 8, 10, 12 poles 384 poles 404, 6, 8 poles 42Mounting 44How to change vibration intensity 46Drawingsextra pageElectric motovibrators 45Originally specialising in immersion vibrators for concrete consolidation, OLI is now the worldwide leader in vibration technology, with a complete range of electric and pneumatic internal and external vibrators .By supplying competitive, high quality products for wide-ranging applications, OLI combines performance and reliability by adapting to the ever-changing market. A strong believer in innovation, OLI is constantly striving to be ahead of the opposition.As a global player in industrial vibration technology, the key focus of OLI’s business strategy is rapid stock delivery, any time, anywhere in the world . Excellent customer service is of pivotal importance: the company guarantees quick order processing and customers worldwide can enjoy access to the same high quality product and services.OLI has access to credible expertise when it comes to finding suitable solutions to customers’ requests. A team of engineers specialised in designing efficient, reliable, and safe solutions backed by globally certified management .OLI provides their customers with state-of-the-art equipment and the blueprint for the next generation of products is already in progress.6PTC thermistor 130 °CSpecific grease retaining deviceTropicalised standardIP66 protectionClass F insulation RELIABILITYEasy mass adjustmentVarious voltages and frequencies availableEasy access to the terminal boxMultiple eye-bolts FLEXIBILITYStandard specifications Array* Except for MVE 710/15N-50A0 and MVE 510/1N-50A078Providing centrifugal force up to 26,000 kgs and with multiple voltage options OLI’s range of electric motovibrators covers several fields of application in every country as well as many different industrial sectors: from food to mining, from foundry to recycling and more.OLI’s electric motovibrators are designed and manufactured using the latest technologies and premium quality materials and components.Vibrator bodies, bearing flanges and shafts are FMEA designed and manufactured using first grade Aluminium alloy, cast iron and steel alloy to withstand heavy duty applications and guarantee safe operation in any condition.Vacuum impregnated windings and class F insulating materials enhance reliability and durability.Top quality bearings and an efficient grease retaining system assure long lasting performance and low noise generation.Adjustable eccentric masses allow easy fine tuning of the Max centrifugal force provided by the vibrator.Several certifications for use in hazardous environments are available in the OLI range to match the most demanding specification worldwide.The OLI Vibrator Rangemass cover fixed massbearingadjustable massshaftrotor flange frame9Grain Processing, Stainless Steel and Screen VibratorCertificationsStandardIncreased SafetyExplosion Proof and Screen VibratorConformity with European Directive - Low voltage 2014/35/UE; Machine Directive 2006/42/EC; ATEX 2014/34/UE - UL 1836. UL 1004-1 - SAC22.2 NO 25. 100. 145* Screen vibrator is also available with the same certifications as the standard, not explosion proof range, mentioned in the first chart of this page.** Soon available.Conformity with European Directive - Low voltage 2014/35/UE; Machine Directive 2006/42/EC; ATEX 2014/34/UE - UL 1836. UL 1004-1 - SAC22.2 NO 25. 100. 145Tx = T100 °C up to size 30 included; T135 °C from size 40 up. T135 °C from size 40 up.Conformity with European Directive - Low voltage 2014/35/UE; Machine Directive 2006/42/EC - ATEX 2014/34/UE - UL 1836. UL 1004-1. UL 674 - CSAC22.2 NO 25. 100. 145Conformity with European Directive - Low voltage 2014/35/UE; Machine Directive 2006/42/EC; ATEX 2014/34/UE* Extended temperature range up to 55 °C available on request.MVE DC Range: II3D Ex tc IIIC T100 IP6610Check the obtained value “e”: •If it is similar to the required one (step 1) the MVE model is correct.• If it is not similar to the required one (step 1) repeat the process (step 2) with a different MVE model.Choose rpm and the amplitude ”e” (0 - peak) suitable for your application:Choose an MVE from the tables of the following pages and use its Wm into this formula:How to choose a motovibrator Circular vibration Linear vibration e = amplitude of vibration 0-peak (mm)n = number of vibrators Wm = working moment (kgcm)M mot = vibrator weight (kg)M vm = vibrating machine weight (without material and vibrators)e =5 n Wm n M mot M vm For tips on installation see page 4411To convert kg into Newton:N =9.81kg»II2D Ex tb IIIC Tx Db IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-3112Class II Div.2: Temp. Class T4ExII 2D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low Voltage2 POLES - 3000/3600 rpmSIZE 10A0SIZE 60A0SIZE 105A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.The latest and most updated information are available online.»Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079- 31, CSA 22.2 N°100, CSA 22.2 N°7713To convert kg into Newton:N =9.81kg»II2D Ex tb IIIC Tx Db IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-3114Class II Div.2: Temp. Class T4ExII 2D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low Voltage4 POLES - 1500/1800 rpmNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.The latest and most updated information are available online.»Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079- 31, CSA 22.2 N°100, CSA 22.2 N°7715To convert kg into Newton:N =9.81kg»II2D Ex tb IIIC Tx Db IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-3116Class II Div.2: Temp. Class T4ExII 2D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low Voltage6 POLES - 1000/1200 rpmNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.The latest and most updated information are available online.»Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079- 31, CSA 22.2 N°100, CSA 22.2 N°7717To convert kg into Newton:N =9.81kg»II2D Ex tb IIIC Tx Db IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-3118Class II Div.2: Temp. Class T4ExII 2D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low Voltage8 POLES - 750/900 rpmSIZE 40A0SIZE 50A0SIZE 60A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.The latest and most updated information are available online.»Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079- 31, CSA 22.2 N°100, CSA 22.2 N°7719IntertekUP TO SIZE 60 (NOT INCLUDED)60Hz masses = 50Hz masses adjusted at 70%ABOVE SIZE 60 (INCLUDED)Specific masses for 60HzTo convert kg into Newton:N =9.81kgMVE STANDARD RANGE»II2D Ex tb IIIC Tx Db IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21) - Directive 2014/34/UE»Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-3120Class II Div.2: Temp. Class T4ExII 2D Temp. Class: 100 °C 135 °C2 POLES SINGLE-PHASE - 3000/3600 rpm* NOTE: Capacitor not supplied with vibrator (to be ordered separately)ELECTRICAL SPECIFICATIONSWm (Kgcm)ModelCentrifugal Force (kg)Weight (kg)Input Power (kW)Nominal Current A maxCable GlandCapacitor *50Hz60Hz50Hz60Hz50Hz60Hz50Hz 60Hz50Hz 60Hz 50Hz(230V )60Hz (115V)Metric50Hz (230V)60Hz (115V)1.3 1.0MVE 60/3E-10A0-M MVE 60/36E-10A0-M 667140.080.090.431.03M16 3.0 6.32.0 1.3MVE 100/3E-10A0-M MVE 100/36E-10A0-M 989550.100.110.54 1.30M16 4.08.03.72.6MVE 200/3E-20A0-MMVE 200/36E-20A0-M18718970.180.211.142.62M208.016.03.7 2.6MVE 200/3E-23A0-M MVE 200/36E-23A0-M 18718970.180.21 1.14 2.62M208.016.06.4 4.5MVE 300/3E-30A0-M MVE 300/36E-30A0-M 321323100.270.28 1.58 3.43M2012.525.0SIZE 10A0SIZE20A0SIZE 30A0* Terminal Connections: Y High Voltage; Δ Low VoltageNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility. The latest and most updated information are available online.IntertekUP TO SIZE 60 (NOT INCLUDED)60Hz masses = 50Hz masses adjusted at 70%ABOVE SIZE 60 (INCLUDED)Specific masses for 60HzTo convert kg into Newton:N =9.81kgMVE STANDARD RANGEClass II Div.2: Temp. Class T4II 3D Temp. Class: 100 °C 135 °CELECTRICAL SPECIFICATIONSWm (kgcm)ModelCentrifugal Force (kg)Weight (kg)Input Power(kW)Nominal CurrentA maxCable Gland *50Hz 60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz (230V)60Hz (115V)Metric0.10.1MVE 3/3E-MICRO-M MVE 3/36E-MICRO-M 46 1.60.030.040.300.80M160.10.1MVE 6/3E-MICRO-M MVE 6/36E-MICRO-M 69 1.60.030.040.300.80M160.40.4MVE 21/3E-MICRO-M MVE 21/36E-MICRO-M 202920.040.070.200.80M160.90.9MVE 41/3E-MICRO-M MVE 41/36E-MICRO-M 4565 2.40.050.070.250.80M16MVE-MICRO - 3000/3600 rpmELECTRICAL SPECIFICATIONSWm (kgcm)ModelCentrifugal Force (kg)Weight (kg)Input Power(kW)Nominal CurrentA max* T e r m i n a l C o n n e c t i o n Cable Gland50Hz60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz60Hz50Hz (230V)50Hz (400V)60Hz (460V)Metric0.40.4MVE 21/3E-MICRO MVE 21/36E-MICRO 202920.040.040.210.120.12Y M160.90.9MVE 41/3E-MICRO MVE41/36E-MICRO 456520.060.060.300.180.18YM16NOTE: Capacitor integrated in the cableTHREE-PHASESINGLE-PHASEMICRO* Terminal Connections: Y High Voltage; Δ Low VoltageNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility. The latest and most updated information are available online.IntertekTo convert kg into Newton:N =9.81kgSIZE 23A0SIZE 40A0SIZE 50A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility. The latest and most updated information are available online.Ex II 2G: Temp. Class T3 - ExII 2D Temp. Class: 100 °C 135 °CT4EX e, tE: 52 POLES - 3000/3600 rpmSIZE 40A0SIZE 50A0SIZE 60A0* Terminal Connections: Y High Voltage; Δ Low VoltageTo convert kg into Newton:N =9.81kgNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility. The latest and most updated information are available online.Ex II 2G: Temp. Class T3 - ExII 2D Temp. Class: 100 °C 135 °CT4EX e, tE: 5* Terminal Connections: Y High Voltage; Δ Low Voltage 4 POLES - 1500/1800 rpmSIZE 70A0SIZE 75A0SIZE 80A0To convert kg into Newton:N =9.81kgNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility. The latest and most updated information are available online.Ex II 2G: Temp. Class T3 - ExII 2D Temp. Class: 100 °C 135 °C 6 POLES - 1000/1200 rpmT4EX e, tE: 5* Terminal Connections: Y High Voltage; Δ Low VoltageTo convert kg into Newton:N =9.81kgNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.»Class I, Div.2 Group A, B, C, D T3 »Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079-31, CSA 22.2 N°100, CSA 22.2 N°77, CSA 22.2 N°60079-731The latest and most updated information are available online.»II 2D Ex tb IIIC Tx Db IP66 »II 2G Ex eb IIC T3 Gb»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 21 - Zone 1) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »IEC 60034-1, IEC EN 60079-0, IEC EN 60079-31, IEC EN 60079-7To convert kg into Newton:N =9.81kg32Ex II 2G: Temp. Class T3 - ExII 2D Temp. Class: 100 °C 135 °CT4EX e, tE: 5* Terminal Connections: Y High Voltage; Δ Low Voltage8 POLES - 750/900 rpmSIZE 80A0SIZE 86A0SIZE 91A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.»Class I, Div.2 Group A, B, C, D T3 »Class II Div.2 Group F, G T4»Conform to UL 1004-1,UL 1004-3, UL60079-31, UL60079-0, CSA 60079-0, CSA 60079-31, CSA 22.2 N°100, CSA 22.2 N°77, CSA 22.2 N°60079-733The latest and most updated information are available online.To convert kg into Newton:N =9.81kg»II 2G Ex db IIB T4 Gb, »II 2D Ex tb IIIC T135°C Db »Ex db IIB T4 Gb»Ex tb IIIC T135°C Db»Ambient temperature from -20°C to +60°C»Compliance with Essential Health and Safety Requirements »IEC EN 60079-0, IEC EN 60079-31, IEC EN 60079-134Ex II 2G: Temp. Class T4Class1 Div.1: Temp. Class T4 Ex II 2D Temp. Class: * Terminal Connections: Y High Voltage; Δ Low VoltageSIZE 50A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.»Class I, Div.1 Group C, D T4 IP66»Conform to UL 1004-1,UL 1004-3,UL1203;UL674,CSA C22.2 No.145, CSA C22.2 No.30-M1986.35The latest and most updated information are available online.»II 2G Ex db IIB T4 Gb,»II 2D Ex tb IIIC T135°C Db»Ex db IIB T4 Gb»Ex tb IIIC T135°C Db»Ambient temperature from -20°C to +60°C»Compliance with Essential Health and Safety Requirements»IEC EN 60079-0, IEC EN 60079-31, IEC EN 60079-136Ex II 2G: Temp. Class T4Class1 Div.1: Temp. Class T4Ex II 2D Temp. Class:* Terminal Connections: Y High Voltage; Δ Low VoltageSIZE 60A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.»Class I, Div.1 Group C, D T4 IP66»Conform to UL 1004-1,UL 1004-3,UL1203;UL674,CSA C22.2 No.145, CSA C22.2 No.30-M1986.37The latest and most updated information are available online.To convert kg into Newton:N =9.81kg»II3D Ex tc IIIC Tx IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 22) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »EN 60079-0, EN 60079-3138Ex II 3D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low VoltageMVE-MILLINGNOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.39The latest and most updated information are available online.»Declaration of conformity “type B” according to: 2014/35/UE - 2006/42/EC - EN 60034-1 »Conform to UL1446 and CSA 22.2 No 0-1040To convert kg into Newton:N =9.81kgEx II 2G: Temp. Class T4Class1 Div.1: Temp. Class T4Ex II 2D Temp. Class:* Terminal Connections: Y High Voltage; Δ Low Voltage»II 2G Ex db IIB T4 Gb,»II 2D Ex tb IIIC T135°C Db»Ex db IIB T4 Gb»Ex tb IIIC T135°C Db»Ambient temperature from -20°C to +60°C»Compliance with Essential Health and Safety Requirements»IEC EN 60079-0, IEC EN 60079-31, IEC EN 60079-1SV SIZE 75A0SV SIZE 85A0NOTE: Adjustable centrifugal force.NOTE: The Model name in the standard range is different: the letter “D” changes in “N”.The MVE-SV is available also as “standard” range, with Ex II 3D certification: Ex II 3D Temp. Class: 135 °CElectrical and dimensional specifications are the same as the “explosion proof” range.»II3D Ex tc IIIC Tx IP66»Equipment and protective system intended for use in potentially explosiveatmospheres (Zone 22) - Directive 2014/34/UE»Compliance with Essential Health and Safety Requirements»EN 60079-0, EN 60079-31»Declaration of conformity “type B” according to:2014/35/UE - 2006/42/EC - EN 60034-1»Conform to UL1446 and CSA 22.2 No 0-104 POLES STANDARD RANGE - 1500/1800 rpm41NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.The latest and most updated information are available online.»Class I, Div.1 Group C, D T4 IP66»Conform to UL 1004-1,UL 1004-3,UL1203;UL674,CSA C22.2 No.145, CSA C22.2 No.30-M1986.To convert kg into Newton:N =9.81kg»II3D Ex tc IIIC Tx IP66»Equipment and protective system intended for use in potentially explosive atmospheres (Zone 22) - Directive 2014/34/UE »Compliance with Essential Health and Safety Requirements »EN 60079-0, EN 60079-3142Ex II 3D Temp. Class: 100 °C 135 °C* Terminal Connections: Y High Voltage; Δ Low VoltageSIZE 30A0SIZE 50A0NOTE: Dimensions with coarse degree of accuracy related to UNI 22768/1This information is provided without warranty, representation, inducement or licence of any kind. It is accurate to the best OLI knowledge or is obtained from sources believed to be accurate. OLI therefore assumes no legal responsibility.»Declaration of conformity “type B” according to: 2014/35/UE - 2006/42/EC - EN 60034-1 »Conform to UL1446 and CSA 22.2 No 0-1043The latest and most updated information are available online.44The base plate surface where the vibrator is mounted has an allowable tolerance of 0.25mm (0.01in), so that the surfaces rest uniformly against each other to avoid internal tension that may cause breakage of the foot of the vibrator.Use 8.8 type bolts, 8.0 type nuts and flat washers belonging to category A EN ISO 7089 / 7092.The graph below shows the correct torque settings for the different bolt sizes used on the vibrators. MountingVibrator / Machine interfaceFIXING SURFACE FLATNESS TOLERANCETapped threaded borehole+ screw+ flat washerSmooth throughborehole+ screw+ flat washer+ nut and counternutRecommendedHMACHINED & NOT PAINTEDSUPPORT PLATEMax 0.25mm (0.01in)45P2Verify that the voltage and frequency supply match the ones indicated on the rating plate of the electric vibrator.If the vibrator is operated via a variable frequency drive do not run it under 20 Hz and not over the rated frequency.Insert the power cable through the cable gland. The lead-in wires have to be of the eyelet-type, pre-insulated, with a bore that suits the terminals of the junction box in order to prevent overheating of the wire. Use only conductors that have a suitable cross-section.Connect the lead wires to the pins (as shown in the diagram below) and tighten them with the specified torque.Do not forget to fix the earthing cable to the provided studs → Compulsory connection!Before closing the junction box make sure that the cover gasket is properly fitted in order to keep the specified IP protection.For more details on vibrator installation refer to product manuals.All electric vibrators MUST be connected to a suitable external overload protection.When using two electric vibrators in sync, each of them has to be connected to an external overload protection that must be interlocked to make sure both vibrators are stopped if one fails.Always use a thermal-magnetic type vibratorprotection, with delayed cut-off, to avoid stopping the vibrator during start-up when the current draw is higher than the rated running current for a few seconds.Cut-off of the overload protection should be set at a maximum of +10% of the rated current.Electrical connectionTERMINAL CONNECTIONSthe factory preset connection of each vibrator.Overload protection46ADJUSTED MASSESWarning:DO NOT grease new motors before installation.OLI motors with roller bearings leave the factory filledwith the right quantity of grease while those with ballbearing do not need any lubrication. TECHNICAL DRAWINGSE1 C1WHEN YOU NEED IT, WHERE YOU NEED IT.w w w.o l i v i b r a.c o mOLI worldwideOLI HeadquartersVia Canalazzo, 3541036 Medolla (MO) - Italy+39 0535 41 06 11info@。
美琪wed-4调音台说明书一、开机前，连接好所有系统。
将推子，均衡器（EQ），PANPADGAL等调回起始状态二、开机后(1)先将音源设备（如CD）的音量开到最大不失真状态。
(2)调节调音台该输入通道的分推子于70%，调大输入增益（GAIN）旋钮到PEAK（峰值）指示灯到刚亮未亮处。
(3)调节音量输出主推子，使输出的VU表指针大致在0VU附近摆动，不允许长时间指针超过+3VU。
此时主推子位置也宜在50%到70%的位置内。
可相应调整输入增益或音源输出电平。
(4)如果还觉得音箱响度不够，可开大功放音量旋钮，注意此时功放不得进入削波状态，否则应换更大功率功放。
(5)以上控制顺序是由输入逐步向输出调整。
如果音源是话筒，由于话筒输入信号很小，初学者调输入通道时常因听不到声音而感到茫然不知所措，此时可先将输出主推子置于70%，再调输入增益旋钮和分推子，再按上述②到④步骤调整。
特别要注意是否因定值率减（PAD）按下，此时应不作衰减。
此法对初学者较适合。
(6)然后按节目要求，分别调整调音台上的EQ，PAN及效果等。
三、下面讲些调音小技巧：(1)对于人声：可将100Hz以下切除，以消除低频噪声，使音色更加纯净。
500-800Hz作少量衰减，使音色不太生硬。
在2KHz-4KHZ 提升3到6dB，可使声音明亮。
对6KHz以上适当衰减可大大增强声音的清晰度，防止不必要的气音和嘶音。
(2)对CD等数码音源，因其录制较好，可不加修饰。
(3)通常Disco厅、交谊舞厅、背景音乐厅等用单声道放音；OK 厅、音乐厅，歌厅等用立体声放音。
(4)下面介绍一下用推子和PAN调节声源的空间声像，即空间位置。
对于演唱声和主乐器声，将PAN调至中间，推子推大，以突出它们；如果声源为立体声，则不可任意摆放PAN和推子，否则演唱声与音乐声合不到一起，声音混乱，应左、右声道各用调音台一路，分别将PAN调到左、右边，两路推子在同一高度上。
A VITEQ磁力振动器MVE50-4原厂进口A VITEQ振动器MVE50-4，配套控制器SCE-EN50-2，成套德国原厂，口碑良好。
A VITEQ控制器SCE-EN50-2（询价打：15 8 0 5 0 6 1 2 1 3）A VITEQ振动器MV12/50-3A VITEQ控制器SRAE-C50/01-1-1A VITEQ控制器SAE-GS33-2A VITEQ振动器MVC50-4A VITEQ振动器MVB50-4A VITEQ振动器MVD50-4A VITEQ振动器MVE50-4A VITEQ控制器SCE-EN50-2A VITEQ磁力振动器MVES50-1P3)De tetor BHH-200BRINKMANN PUMPTFS 376/4095L/min40bar充电器\SKYLLA-TG24\25 30A victron energy里奇36273PINTER 工作压力开关MANOCOME-IP65/2KA 0-16BARAT0S 型号DHA-0751/2/M24DCDAMCOS 160B4171 指示灯开关卡特蓄电池 9X-9730品牌：麦塔雷斯型号：MHP350A198EVAB207迪创迪创火焰探头X5200A4N13W2，防护等级TP56&ExdIIBT4IDC通讯板（与上面的探头配套的）006642-005电源底板（与上面的探头配套的）006590-003迪创火焰探头PIR9400A3A1AW，防护等级IP56&ExdIIBT4IDC通讯板（与上面的探头配套的）006642-004电源底板（与上面的探头配套的）006586-002LM303摩菲的油位保持器摩菲 DVU150 (55700299) 排泄阀FEDERAL SIGNAL CORPORATION 防爆对讲机正确型号310X-MVCULTER-HAMMER 接触器6702ED584BLAGDON气动隔膜泵B25 1AAABBTTSautronica 16BAR编号40766订货型号是GT300C2G16HYPRO水泵9304C-HM1CViatran PRESSURE TRANSDUCER, MODEL 245, 0-700KPa，0-5 VDC OUTPUT model: 245AMGX1691B加热器\CX/15397-02\380V/6.6KW\CALORITECH阿密龙 3019 95 GPM1.5 黄铜手枪式DYNALCO速度开关SW-200BSPM 2A26611BREVINI 减速机 CTU3200.1 S.N.：728815VS2 开关摩菲MEDC BGEQ4B6B2DDA7RAUTRONICA EAC-300A/B Processor cardDANIAMANT TYPE：L1611)detectormodel : 116-5861-011.5300, MODEL NO.HC300PLB7A2W1; DATE CODE:08DEC057674阿美特克3050水分析仪校验管 305431901SBLAGDON气动隔膜泵B25 1AAABBTTS泰科探头601FEX-MPRICE PUMP3MS50SS-412-21211-100-30-1T5真空泵HITECH INSTRUMENTS氧电池 813-9050WOMA安全阀 G1/2 S8.5 135Bar 1件件号是001.1108autronica detector1)BHH-320/X12)BDH-5003)BDH-500/N4)BDH-500/EX康士廉Part.no 001155 SALWICO本迪克斯 450修井机CAT3408空气压缩机GMC SINEAXModel:808-12120000TRANSMITTERREF:128802本迪克斯干燥器1A-592\AD-2品牌：OLAER奥莱尔型号：ELM0.75-210/00/AFSOLDO品牌限位开关型号: SX02200-2型号: SXC4200-2型号: SX73201-2德鲁克压力传感器PTX-5072-TC-A1-CA-H1-PR巴士德传感器 9692X-1CC-3-BNETSAFETY PHOENIX三频火焰探测器 IR3S-R品牌 WANNER型号 G40XDSNNNNCBMaker: MMC INTERNATIONAL CORP.Type: MMC SAMPLING DEVICE PART NO.:2326C1821540M1/2 40M Closed Self Contained Sampling UnitMaker: MMC INTERNATIONAL CORP.Type: MMC SAMPLING DEVICE PART NO.:S-2562-TS-CPL-SHT TS AdaptorVEGA 型号：PS68.XXE1H2HANAKQualitrol1)092-052-012)CAS-724-1+FLA-644-13)CAS-724-1+FLA-644-1+GAS-046-6EVAC蓝色接口6540524EVAC铜阀套5980800EVAC控制器6541675EVAC控制器5775500Evac冲水按钮3510100Evac水压阀5774002EVAC配件6541056EVAC配件5779400EVAC配件5779500EVAC配件5430103EVAC配件5980800EVAC配件5800000EVAC排气阀5435015Evac水压阀5774000EVAC按钮5900200EVAC气动按钮5900204EVAC带适配器法兰的活化剂6541675EVAC灰水阀6542811EVAC连接套筒5433572EVAC止回阀5959902EVAC橡胶膜片5435169EVAC执行机构5775500EVAC背板总成5780000DNH室内扬声器[][HS-8EEXMNT][]室内扬声器[][HP-10T][]防爆扬声器[][DSP-15EEXMNT][]哈威 V30D-140 RDN-2-1-04 LSN250-1杰斯曼联动台 KST19+KFS10威创压力传感器5705BPSX1052RGS ELECTRO PNEUMATICS LTDModel:VSK1001 SEALS FOR RGS 1''BSP 3 PORT SPOOL CONTROL VALVE H1003-9品牌：BITZERCOMPRESSOR\6H35.2-40P\BITZER REFRIGERATIOTR 编码器/CE100M.ArT.Nr100.00390摩菲室外防雨型振动开关VS2-IP67NUFLO CAMERON：1.Make: NUFLO CAMERON，Model: Turbine Flow Meter ，P/N: 9A-100062687，2.Make: NUFLO CAMERON，Model: Turbine Flow Meter ，P/N: 9A-100062810，3.Make: NUFLO CAMERON，Model: Turbine Flow Meter ，P/N: 9A-100009810，BRINKMANN TFS376/40+001resQmaxmodel:KIT411model:KIT457AMETEK陶瓷过滤器74422SE氧化锆锆头71785SEAUTRONICA控制板模块BSJ-310控制板模块BSD-310控制板模块BSL-310控制板模块BSS-310A世伟洛克Swagelok高压阀.DN12 6000psi.SS-6NBSW8T-G.316SS高压阀门.DN6 PN35.SS-6HNBSW8T-GSMOKE DETECTOR\BHH－500 SMOKE DETECTOR\BHH－500\AUTRONICA FIRE AND SECURITY\火气系统美国SAMSON电磁阀 type 3962, 24VDC, 3/2-way, IP 66, Eex d IIC T6, elec conn. 1/2"NPTLEROY SOMER电机3-LSES225MR-T N703333H11003 2011 IP55IK08 S1 DE:6313ZZC3 NDE:6313ZZC3 △400V 50HZ 1471min-145KW 84Ametrix振动探头5485C-007-040-M13776寸流量计为CAMERON 型号：9A-100062997,Rev.02，显示速度和总量；大8位3 / 4”显示器；电池采用一个“D”型1.5伏碱性电池。
Fleetguard燃油预滤器型号 FH234351，ANALYZER\NUFLO TECHNOLOGY\100005130\WATER FLOW TURBINE METER2，MAGNETIC PICKUP\NUFLO TECHNOLOGY\100002077\WATER FLOW TURBINE METERCELESCOPT5MA-125-S47-UP-420E-M6PT5MA-80-S47-UP-420E-M6品牌：科诺尔KNOLL型号：KTS-32-48-T(1) Skylla-TG 24/50 AC185 265V 2pcs . Price would be(2) Skylla-TG 24/80 AC185 265VThermo Element温度探头 GENP NO RTO31040温度探头 GENP NO:RTO31104CHARGEMASTER Charger2 x Chargemaster 24v/60-3 @8 x Chargemaster 24v/80-3 @分析仪预处理阀门SS-1RS4(Swagelok）分析仪预处理阀门SS-4P4T(Swagelok）分析仪预处理阀门SS-42GXS4(Swagelok）金属软管SS-FM8RF8RF860CM金属软管SS-FM16RF16RF1660CM金属软管SS-FJ24PF24PF2460CMHochiki探测器SPC-24意大利SPAGGIARI减速机sw/063tSkylla-TG 24/50Skylla-TG 24/80荷兰VICTRON (1) Skylla-TG 24/50 AC185 265V(2) Skylla-TG 24/80 AC185 265VScott1>.SCOTT Harness for above AV-2000 Facepiece,Part.No.804063-01 20pcs2>，SCOTT AV-2000 Facepiece without Harness, Large,Part.No.804019-02 20pcs3>.742 Series Twin Cartridge 1/4 TurnAdapter, P/N#805622-01 20pcs?SEALWELD 80润滑脂 S-EQ-SGC 911润滑脂 5050#密封脂 X5050 密封脂canrig顶驱配件AY11450奔驰A6481531679FUJI富士断路器TR-ON/3 1.4-2.2A清洗剂 VCPLUS S-VAP-SGC顶驱装置配件canrig 1050E-712 黄油嘴canrig风道总成AY10032canrig顶驱润滑油滤芯H11-1003-010德国 DUNGS阀 MB-VEF 407 B01 S10(220985)力士乐 DBDS10P1X/315，滤芯的美国DOMNICK的滤芯：39504802officineorobiche的流量计212R-J-2-G3-CO-RPJU-XX，德国LEUZE条码扫描仪BCL31SM100（10-30VDC）CR43674普兰索力高压泵 SM14IMO螺杆泵ACG 052K7 NTBPACG 052K7 NTBP卡特散热器总成 216-9349散热器盖 197-9216卡特增压器2507699 TURBO GP-BAS压力变送器, Type: 8472.78.5717, 0-10 Bar-G, 4-20 mA, 9~30VDC, Maker: Trafag威格士300AA00086A力士乐生料立磨稀油站阀座溢流阀 2FRM10-21B/25L生料立磨稀油站油泵溢流阀 DBDA10P10B/315skf 轴承 6322C3INTERMOT NHM6-400SABBTYPE：L3 139LBSTOP SOLENOID L43.002.1.3 969108UFM流量开关MN-ASB120GLM-16-500V.9-A1WLDungs 连接器250VAC/10AFENWAL热探测器12－E27121－000－04 190FAUXILLARY ENGINE FUEL OIL LINE FLOWMETERMachinery Type :AUX ENGINEMachinery Type, model: VZO 25 FL 130/25Serial no.:4746658Name & Address of Maker:CONTOILNOP油泵212HB科沛达 NM80/16AE1日本叶片油泵PV2R2-33-F-RAA-41汉森气管接头3000比例伺服阀DLHZ0-T-040-L7131TESCOM 44-2214-241卡特4218547（2765906）威格士V20F-1S13S-1C11K-22DANAHER伺服驱动器S61000美国Kollmorgen科尔摩根伺服电机AKM65K-ANCNR-00DGMPC-5-ABK-BAK-30PCGV8FD10月DG4V-5-6CJ-M-U-H6-20图尔克Bi2-EG08-AP6X-V1131SWKP3-2/S901261770 COUPLING,FLEXIBLE,SPLIT SLEEVE,SEPCO,3JES-SPLIT Manufacturer Part Number3JES-SPLIT Manufacturer：SEPCOsick编码器1031449 ARS60-A4B08192派克Parker温度开关SCTSD-150-10-05-40-150压力开关SCPSD-010-14-25压力开关SCPSD-060-14-25富士变频器FRN7.5G1S-4C英格索兰气动马达M007RHR027AR4SIEMENSP/N:6SE7026-0ED61Delivery time: 06 - 08 weeks.道茨计量泵D-100N-105/B-13施迈斯胶球 RS15WALTHER快速接头LP-006-0-WR017-01-2-GLLP-006-2-WR017-01-2-GL普兰索力MS45卡特散热器盖 197-9216散热器总成 216-9349SICK编码器1031449 ARS60-A4B08192曼牌CF-1810 C27-1050METARIS麦塔雷斯泵V20F-1S13S-1C11K-22宝德Baldor M3714T-58奥玛电动执行器SA10.1-F10日本Koyo光洋编码器TRD-2TH600BF DC10.8-26.4V本特利振动探头BENTLY NEVADA VELOMITOR PN330500 100mv/m/s(4mv/mm/s) G07K02MG。
