DELL M100E CMC命令行

1.CMC IP 地址的察看：

ifconfig \\用于察看 CMC 的 IP 地址，例如：

2.CMC IP 地址的修改：

$racadm

racadm

racadm getsysinfo

racadm getmodinfo

$racadm setniccfg \\用于察看CMC的IP地址，例如：

$ racadm setniccfg -s 192.168.128.120 255.255.255.0 192.168.128.1

Static IP address modified successfully

等候大约15秒才能生效

$ ifconfig

eth0 Link encap:Ethernet HWaddr 00:1A:A0:FF:F7:04

UP BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

$ ifconfig

eth0 Link encap:Ethernet HWaddr 00:1A:A0:FF:F7:04

inet addr:192.168.128.120 Bcast:192.168.128.255 Mask:255.255.255.0

UP BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

3.察看 CMC 系统信息：

racadm getsysinfo \\用于察看CMC系统信息，例如：

$ racadm getsysinfo

CMC Information:

CMC Date/Time = Fri, 31 Oct 2008 05:13:16 AM

Primary CMC Version = 1.20

Standby CMC Version = N/A

Last Firmware Update = Thu Sep 25 01:36:04 2008

Hardware Version = X28

Current IP Address = 192.168.0.120

Current IP Gateway = 192.168.0.1

Current IP Netmask = 255.255.255.0 DHCP Enabled = 0

MAC Address = 00:1A:A0:FF:F7:04

Current DNS Server 1 = 0.0.0.0

Current DNS Server 2 = 0.0.0.0

DNS Servers from DHCP = 0

Register DNS CMC Name = 0

DNS CMC Name = cmc-6T9N72X

Current DNS Domain =

Chassis Information:

System Model = PowerEdgeM1000e

System AssetTag = 00000

Service Tag = 6T9N72X

Chassis Name = Dell Rack System

Chassis Location = [UNDEFINED]

Power Status = ON

4.、察看 CMC 机箱内部的模块和模块名称:

racadm getmodinfo \\用于察看机箱内部的模块清单，例如：

$ racadm getmodinfo

Chassis Present ON Not OK 6T9N72X

Fan-1 Present ON OK

Fan-2 Present ON OK

Fan-3 Present ON OK

Fan-4 Present ON OK

Fan-5 Present ON OK

Fan-6 Present ON OK

Fan-7 Present ON OK

Fan-8 Present ON OK

Fan-9 Present ON OK

PS-1 Present Online OK

PS-2 Present Failed(No AC) Not OK

PS-3 Present Online OK

PS-4 Not Present N/A N/A N/A

PS-5 Not Present N/A N/A N/A

PS-6 Not Present N/A N/A N/A

CMC-1 Present Primary Not OK N/A

CMC-2 Not Present N/A N/A N/A

Switch-1 Present ON OK 4ZXW7F1

Switch-2 Present ON OK 3P9HSB1

Switch-3 Not Present N/A N/A N/A Switch-4 Not Present N/A N/A N/A

Switch-5 Not Present N/A N/A N/A

Switch-6 Not Present N/A N/A N/A

Server-1 Not Present N/A N/A N/A

Server-2 Not Present N/A N/A N/A

Server-3 Not Present N/A N/A N/A

Server-4 Present OFF OK 188Q72X

Server-5 Not Present N/A N/A N/A

Server-6 Not Present N/A N/A N/A

Server-7 Not Present N/A N/A N/A

Server-8 Not Present N/A N/A N/A

Server-9 Not Present N/A N/A N/A

Server-10 Not Present N/A N/A N/A

Server-11 Not Present N/A N/A N/A

Server-12 Not Present N/A N/A N/A

5.连接到其他设备的配置界面:

connect 命令用于连接到其他模块的命令行界面,例如：

要配置网络交换机1，便输入 $connect switch-1

$ connect switch-1

connect: acquiring remote port.

Connected to remote port.

Escape character is '^\'. （由交换机界面退回CMC界面输入 ctrl+\ ）

console>

6.重启动 CMC

$ racadm racreset

7.恢复 CMC 到出厂值（CMC 反初始化）

$ racadm racresetcfg

8.其他常用 racadm 子命令

$racadm ? -- display usage summary for a subcommand

arp -- display the networking arp table

chassisaction -- execute chassis or switch power-up/down/cycle or KVM powercycle

clrraclog -- clear the CMC log

clrsel -- clear the System Event Log (SEL) cmcchangeover -- Changes the redundant state of the CMC from active to standby and

vice versa

config -- modify CMC configuration properties

deploy -- deploy blade by specifying required properties

feature -- display features active on the chassis/ feature deactivation

featurecard -- Feature card status and list the available features

fwupdate -- update the firmware on a CMC, server, IOM inf, or KVM

getassettag -- display asset tag

getchassisname -- get the chassisname

getconfig -- display CMC configuration properties

getdcinfo -- display general I/O module and DC misconfiguration information

getflexaddr -- display the MAC addresses per slot/status of Flexa all slots and

fabrics

getioinfo -- display general IO information

getkvminfo -- display the KVM module information

getled -- display the LED settings on a module

getmacaddress -- get MAC/WWN addresses

getmodinfo -- get module configuration and status information

getniccfg -- display network settings for modules

getpbinfo -- get power budget status information

getpminfo -- get power management status information

getraclog -- display the CMC log

getractime -- display the current CMC time

getredundancymode -- gets the redundancy mode of the CMC

getsensorinfo -- display system sensors

getslotname -- gets the name of the slot in the chassis

getssninfo -- display session information

getsvctag -- display service tag information

getsysinfo -- display general CMC and system information

gettracelog -- display the CMC diagnostic trace log

ifconfig -- display network interface information

netstat -- display routing table and network statistics

ping -- send ICMP echo packets on the network

racdump -- display CMC diagnostic information

racreset -- perform a CMC reset operation

racresetcfg -- restore the CMC configuration to factory defaults

serveraction -- perform system power management operations

setassettag -- set the asset tag for the specified module

setchassisname -- sets the name of the chassis

setflexaddr -- enable/disable the Flexaddress feature on a per fabric, per slot basis

setled -- set state of the LEDs on a module