下载文档原格式
磷酸铁锂公司企业名录 Document number：PBGCG-0857-BTDO-0089-PTT19981、深圳市比克电池有限公司成立于2001年8月，美国纳斯达克上市公司，注册资本8260万美元，是一家集锂电池研发、生产、销售为一体的国家高新技术企业。
比克工业园区坐落于深圳东部大鹏湾占地26万平方米，员工6000余人。
2、湖南杉杉新材料有限公司是由宁波杉杉股份有限公司（占75%的股份）和中南大学（占25%的股份）联合创办。
成立于2003年11月，锂离子电池正极材料制造商，是湖南省高新技术企业，专业致力于生产锂离子电池正极材料，以钴酸锂为主要产品，应用于便携式资讯设备如手机、笔记本电脑、移动DVD、数码相机、电动工具等领域，同时于2004年3月正式推出了锰酸锂，应用于电动交通工具等大型动力电源领域。
目前产品有钴酸锂、锰酸锂、镍钴二元系、镍钴锰三元系、磷酸铁锂等。
中国锂电池正极材料行业重点企业简介二、中国宝安集团股份有限公司三、厦门钨业股份有限公司四、中信国安盟固利电源技术有限公司五、石家庄市中洲实业总公司六、湖南瑞翔新材料有限公司七、宁波金和新材料有限公司八、北京当升材料科技有限公司九、北大先行科技产业有限公司十、深圳市振华新材料股份有限公司3、深圳市山木电池科技有限公司1997年10月在广东省珠海市成立,是中国第一家专业生产可充电锂电池的厂家,2006年初,山木公司将工厂搬迁至深圳市横岗深坑村第三工业区厂B公司现主要有以下1.圆柱电池事业部.2.数码电池事业部.3.动力电池事业部.异型圆柱电池系列有直径07系,08. 10 .12铁锂动力电车系列有400mah到１０００0mah等不同容量近１０个规格品牌mottcell型号IFR26650基本参数电池类型锂电池电压有效期1年技术参数标准容量3000mAh充放电次数2000电池容量3000mah开路电压快速充电电流3000mA快速充电时间1h适用范围机车型：电动自行车电动轿车电动工具标准电压适用温度范围-20；+60 ℃直径26*65mmmm贮存温度20度最大连续工作电流6000mah标准充电电流1500mA标准充电时间2h品牌mottcell型号IFR42120基本参数使用期5年额定容量10AH技术参数标准电压直径42 mm充放电次数1500标准充电时间2h标准充电电流5000mA标准容量10000mAh4、河南新太行电源有限公司（国营七五五厂）是一家专业从事动力锂离子电池研发、生产、销售的高科技公司，公司座落于河南新乡牧野经济开发区。
宁德时代磷酸铁锂电池参数
宁德时代磷酸铁锂电池是一种高品质的锂离子电池，具有高能量密度、长寿命、低内阻、高温性能稳定等优点。
以下是宁德时代磷酸铁锂电池的详细参数：
1. 电压：宁德时代磷酸铁锂电池的额定电压为3.2V，最大充电电压为3.65V，最大放电电压为
2.5V。
2. 容量：宁德时代磷酸铁锂电池的容量范围从10Ah到300Ah，容量一般是指电池能够储存的电荷量，越大的容量意味着电池越能够持续供电。
3. 充电速率：宁德时代磷酸铁锂电池的标准充电速率一般为0.2C，最大充电速率为1C，即电池总容量的倍率，如1C充电速率表示1小时内将电池容量充满。
5. 循环寿命：宁德时代磷酸铁锂电池具有较长的寿命，通常能循环5000次以上，循环寿命受到使用环境、充电方式和电流大小等多种因素的影响。
6. 重量：宁德时代磷酸铁锂电池的重量相对较轻，一般约为30kg，具体重量与电池容量和尺寸相关。
目前磷酸铁锂电池成本基本在3000-5000元/kwh之间。
比亚迪价格较为便宜，为3000元/kwh，万向集团平均为9-10元/AH，折合价格也为3000元/kwh，天津力神面向高端客户，主要用来出口美国，原料成本较高，电池价格在4000-5000元/kwh.锂电池的生产又可拆分为隔膜、电解液、正极材料、负极材料4个子行业，这些材料分别占锂电池成本的40%~46%、10%~14%、5%~11%和5%~15%。
据专家介绍，隔膜是锂电材料中技术含量最高的高附加值材料，毛利率70%以上。
隔膜的性能优劣，直接影响电池的容量、循环及安全性能等特性，目前国内尚无公司能够生产，包括比亚迪在内都需要进口。
据悉，生产小型锂电池隔膜的佛塑股份承担了国家863计划中隔膜技术的研发任务。
电解液号称锂电池的“血液”，是锂电池获得高电压、高比能等优点的保证，江苏国泰是国内生产电解液的龙头企业，该公司正在研发被国外垄断的六氟磷酸锂项目的合成技术，六氟磷酸锂是生产电解液的重要电解质，目前主要依靠进口。
六氟磷酸锂是电解液的核心原材料，占电解液成本的50%左右。
由于生产技术难度非常高，在国际上由东电化学工业、森田化学等几家日本企业垄断。
国内生产正级材料的企业很多，但大多数生产钴酸锂、锰酸锂等，真正生产磷酸铁锂的厂家并不多。
磷酸铁锂正极材料做出大容量锂离子电池更易串联使用，以满足电动车频繁充放电的需要。
从未来趋势看，具有无毒、无污染、安全性能好、原材料来源广泛、价格便宜、寿命长等优点，是新一代锂电池的理想正极材料，会成为我国正级材料主导产品。
深圳贝特瑞新能源材料股份有限公司是国内唯一的锂电池磷酸铁锂正极材料标准制定者，也是国内唯一的锂电池碳负极材料标准制定者。
在锂电池的负极材料中，石墨类碳负极材料以其来源广泛、价格便宜，一直是负极材料的主要类型。
我国拥有丰富的天然石墨矿产资源，在以天然石墨为原料的锂离子负极材料产业化方面，深圳贝特瑞也是国内龙头企业。
地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）*************FAX：86（0）*************DATE: 2015/11/04Cylindrical LIFEPO4 BatterySpecification圆柱型磷酸铁锂电池规格书MODEL/型号: IFR 14500-500mAh 3.2VPrepared By/Date 编制/日期Checked By/Date审核/日期Approved By/Date批准/日期冯时春/2015.11.04Customer Approval 客户批准Signature确认Date日期Company Name：公司名称：Company Stamp：客户印章：--- 保密文件---地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）*************FAX：86（0）*************DATE: 2015/11/04Amendment Records （修正记录）Edition (版本) Description（记述）Prepared by（编制）Approved by（批准）Date（日期）A First Publish 冯时春2015/11/04地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）*************FAX：86（0）*************DATE: 2015/11/041 Scope（适用范围）This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd.本说明书适用于本书中所提及的银凯动力科技有限公司制造的电池。
2 Product Specification（产品技术规格）Table 1 (表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）1 Rated Capacity（额定容量）Typical（标称容量）500mAh Standard discharge（0.2C5A)after Standard charge（标准充电后0.2C5A标准放电）Minimum(最小容量)475mAh2 Nominal Voltage（正常电压）3.2VMean Operation Voltage（即工作电压）3 Voltage at end ofDischarge（放电终止电压）2.0VDischarge Cut-off Voltage（放电截止电压）4 Charging Voltage(充电电压)3.65V5 来料电压≥3.3V6 Internal Impedance(内阻)≤80mΩInternal resistance measured atAC 1KH Z after 50% charge（半电态下用交流法测量内阻）The measure must uses thenew batteries that within oneweek after shipment and cyclesless than 5 times(使用出货后不到一个星期及循环次数少于5次的新电池测量)7 Standard charge（标准充电）Constant Current 0.2C5AConstant Voltage 3.65V0.01 C cut-off（持续电流：0.2C5A持续电压：3.65V截止电流：0.01 C）8 Standard discharge（标准放电）Constant current 0.2C5Aend voltage 2.0V（持续电流：0.2C5A截止电压：2.0V）地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）*************FAX：86（0）*************DATE: 2015/11/04Continuous the table 1 (续表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）9 Fast charge(快速充电)Constant Current 0.5CConstant Voltage 3.65V0.01 C cut-off（持续电流：0.5C持续电压：3.65V截止电流：0.01 C）10 Fast discharge(快速放电)Constant current 1.0Cend voltage 2.0V（持续电流：1.0 C截止电压：2.0V）11 Maximum ContinuousCharge Current(最大充电持续电流)1.0 C12 Maximum ContinuousDischarge Current（最大放电持续电流）1.0 C13 Operation TemperatureRange（工作温度范围）Charge（充电）: 0~45℃60±25%R.H.Bare Cell（电池储存湿度范围）Discharge（放电）: -10~60℃14 Storage TemperatureRange（储存温度范围）Less than 1 year: -20~25℃（小于一年：-20~25℃）60±25%R.H.at the shipment state（出货状态时的湿度范围）less than 3 months: -20~40℃（小于3个月：-20~40℃）Less than 1 month : -20~60℃（小于1个月：-20~60℃）15Weight电池重量About 18.0g16Cell Dimension（单体电芯尺寸）High/高度：50.0±0.4 mmInitial Dimension（初始尺寸）Diameter/直径: 14.1±0.2地址：广东省深圳市坪山新区金荔科技园4栋TEL：86（0）*************FAX：86（0）*************DATE: 2015/11/043 Performance And Test Conditions (电池性能及测试条件)3.1 Standard Test Conditions（标准测试条件）Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 23±3℃and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
ENGLIS.Li-ion Cylindrical BatterySpecificationLi -i o n 14500 3.7V 800m A h50.5-1.01 .ScopeThis specification describes the basic performance, technical requirement, testing method, warning and caution of the Li- ion Cylindrical rechargeable battery .The specification only applies to RS PRO Ltd.2. Products assembly drawing and size refers to picture 13.SpecificationNO.ItemSpecifications3.1Typical Capacity 820mAh @ 0.2C Discharge Minimum capacity 800mAh @ 0.2C Discharge 3.2Nominal voltage3.7V3.3Standard ChargeCC/CV,0.2C5A, 4.20V3.4Standard Discharge CC,0.2C5A, 3.00V3.5End-of-charge Voltage4.20V±0.05V3.6End-of-charge Current 0.02C5A （At CV mode）3.7End-of-discharge Voltage 3.00 V3.8Charging Time 8.0hours（standard charge）3.9Quick Charge Current 800mA （1.0C 5rate）3.10Quick Discharge Current 1600mA （2.0C 5rate）3.11Max Discharge Current 2400mA （3.0C 5rate）3.12Initial Impedance Max:70m3.13 Weight Approx(约)：20.2±2g3.14Operating temperature Charging ： 0℃~45℃Discharging ：-20℃~60℃3.15Storage temperature -5℃~35℃3.16Storage Humidity ≤75% RH3.17Appearance Without scratch, distortion, contaminationand leakage3.18Standard environmental conditionTemperature ： 25±2℃Humidity : 45-75%RHAtmospheric Pressure ： 86-106 KPA3.19Temperature Dependence of Discharge Capacity @ 0.2C DischargeChargetemperatureDischarge temperature25℃-10℃0℃15℃25℃40℃Relative Capacity50%80%90%100%100% 4 General PerformanceNo.Item Test Methods and Condition Criteria4.10.2CCapacityAfter standard charging, rest battery for 10min,then discharging at 0.2C to voltage 3.0V,recording the discharging time.≥300min4.2Cycle Life Constant current 0.5C charge to 4.2V, thenconstant voltage charge to current declines to0.01C, rest 10min，constant current 0.5Cdischarge to 3.0V，rest 10min. Repeat abovesteps till continuously discharging capacity≥300 times(次)Higher than 80% of the Initial Capacities of the Cells4.3Capability ofkeepingelectricity20±5℃, After standard charging, rest thebattery 28days, discharging at 0.2C to voltage3.0V, recording the discharging time.≥240min5 Environment PerformanceNo.Item Test Methods and Condition Criteria5.1Discharge athightemperatureAfter standard charging, rest the cells 4h at60±2℃, then discharging at 1C to voltage 3.0V,recording the discharging time.≥54min5.2Discharge atlowtemperatureAfter standard charging, rest the cells for 16h at-20±2℃, then discharging at 0.2C to voltage 3.0V,recording the discharging time.≥210min5.3ThermalshockPut the cells in the oven. The temperature of theoven is to be raised at 5±2℃ per minute to atemperature of 130±2℃ and remains 30 minutes.No fire, nosmoke6 Safe CharacteristicNo.Item Test Methods and Condition Criteria6.1Over chargetestingAt 23±5℃, charging cells with constantcurrent 2C to voltage 5.0V, Stop test till cellstemperature 10℃ lower than max temperature.No smoke or fire6.2OverdischargetestingAt 23±5℃, According to the requirements ofstandard charge, the cells will be discharge tocut-off voltage, then connect with external loadof 30 ohm for 24 hours.No fire, nosmoke, noleakage.6.3Short-circuittestingAt 23±5℃, After standard charging,connect cells anode and cathode by wire whichimpedance less than 80±20mΩ, keep 6h.No smoke or fireAbove testing of safe characteristic must be with protective equipment.※7. CAUTIONS IN USETo ensure proper use of the battery please read the manual carefully before using it. Handling(1)Do not expose to, dispose of the battery in fire.(2)Do not put the battery in a charger or equipment with wrong terminals connected.(3)Avoid shorting the battery(4)Avoid excessive physical shock or vibration.(5)Do not disassemble or deform the battery.(6)Do not immerse in water.(7)Do not use the battery mixed with other different make, type, or model batteries.(8)Keep out of the reach of children.(9)Do not place in a pocket.charge and dischargeBattery must be charged in appropriate charger only.Never use a modified or damaged charger.Do not leave battery in charger over 24 hours.Store the battery in a cool, dry and well-ventilated area.Regulations vary for different countries. Dispose of in accordance with local regulations.8. Battery operation instruction8.1 ChargingCharging current：Cannot surpass the biggest charging current which in this specification book stipulated。
地址：省市坪山新区金荔科技园4栋DATE: TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 83962015/11/04地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/04Amendment Records（修正记录）Edition (版本) Description（记述）Prepared by（编制）Approved by（批准）Date（日期）A First Publish 时春2015/11/04地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/041Scope（适用围）This specification is applied to the reference battery in this Specification that manufactured by Yinkai Power Technology Co., Ltd.本说明书适用于本书中所提及的银凯动力科技制造的电池。
2Product Specification（产品技术规格）Table 1 (表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）1 Rated Capacity（额定容量）Typical（标称容量）450mAh Standard discharge（0.2C5A)after Standard charge（标准充电后0.2C5A标准放电）Minimum(最小容量)450mAh2 Nominal Voltage（正常电压）3.2VMean Operation Voltage（即工作电压）3Voltage at end ofDischarge（放电终止电压）2.0VDischarge Cut-off Voltage（放电截止电压）4 Charging Voltage(充电电压)3.65V5 出货电压≥3.28V6 Internal Impedance(阻)≤130mΩInternal resistance measured atAC 1KH Z after 50% charge（半电态下用交流法测量阻）The measure must uses the newbatteries that within one weekafter shipment and cycles lessthan 5 times(使用出货后不到一个星期及循环次数少于5次的新电池测量)7 Standard charge（标准充电）Constant Current 0.2C5AConstant Voltage 3.65V0.01 C cut-off（持续电流：0.2C5A持续电压：3.65V截止电流：0.01 C）8 Standard discharge（标准放电）Constant current 0.2C5Aend voltage 2.0V（持续电流：0.2C A地址：省市坪山新区金荔科技园4栋TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 8396DATE:2015/11/04 Continuous the table 1 (续表1)No. (序号)Item（项目）General Parameter(常规参数)Remark（备注）9 Fast charge(快速充电)Constant Current 0.5CConstant Voltage 3.65V0.01 C cut-off（持续电流：0.5C持续电压：3.65V截止电流：0.01 C）10 Fast discharge(快速放电)Constant current 1.0Cend voltage 2.0V（持续电流：1.0 C截止电压：2.0V）11 Maximum ContinuousCharge Current(最大充电持续电流)1.0 C12 Maximum ContinuousDischarge Current（最大放电持续电流）1.0 C13 Operation TemperatureRange（工作温度围）Charge（充电）: 0~45℃60±25%R.H.Bare Cell（电池储存湿度围）Discharge（放电）: -10~60℃14 Storage Temperature Range（储存温度围）Less than 1 year: -20~25℃（小于一年：-20~25℃）60±25%R.H.at the shipment state（出货状态时的湿度围）less than 3 months: -20~40℃（小于3个月：-20~40℃）Less than 1 month : -20~60℃（小于1个月：-20~60℃）15Weight电池重量About 20.0g16Cell Dimension（单体电芯尺寸）High/高度：50.0±0.4 mmInitial Dimension（初始尺寸）Diameter/直径: 14.1±0.2地址：省市坪山新区金荔科技园4栋DATE:TEL：86（0）0755-2308 8336 FAX：86（0）0755-2308 83962015/11/043Performance And Test Conditions (电池性能及测试条件)3.1 Standard Test Conditions（标准测试条件）Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 23±3℃and relative humidity of 45~85%. If it is judged that the test results are not affected by such conditions, the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池，且未进行过五次以上的充放电循环。
目录1 适用范围 (1)2 产品类型 (1)3 单体电池尺寸 (1)4 标称技术参数 (2)5 测试条件 (3)6 电池性能 (4)7 运输 (5)8 贮存及其它事项 (5)9电池使用时操作指示及注意事项 (7)10电池使用时警告事项及注意事项 (8)11附录 (9)规格书修订记录日期内容备注2017-10-17 新发行 A1 适用范围本标准描述了惠州亿纬锂能股份有限公司生产的可充电铝壳磷酸铁锂动力电池（产品规格：3.2V、 280Ah）的产品类型、基本性能、测试方法和注意事项。
本产品适用于车载动力系统及储能系统等。
2 产品类型2.1产品名称：铝壳磷酸铁锂动力电池2.2型号规格：LF2803 单体电池尺寸：项目描述尺寸W 宽度174.0±0.5mmT 厚度72.0±0.5mmH 高度(总高) 205.0±0.5mmH1 高度（主体高）200.0±0.5mmD 极柱中心距90.0±1.0mm极柱为双铝极柱结构，M6内螺纹方式,使用激光焊接方式进行连接。
4 标称技术参数序号项目参数备注1 标称容量（Nominal）**********放电(25±2)℃,1.0C恒流放电，2.5V截止。
2 最小容量（Minimum）**********放电3 标称电压 3.2V4 内阻≤0.25mΩ5 充电（恒流恒压CC-CV）最大充电电流1C在0℃～45℃条件下，电池最大充电电流不超过1C。
充电截止电压 3.65V6 放电最大放电电流1C 放电截止电压 2.5V7 充电时间标准充电 2.0h 0.5C充电(时间为参考值)快速充电 1.0h 1.0C充电（时间为参考值）8 推荐SOC使用窗口SOC:10%～90%9 充电条件下的工作温度0℃～55℃具体详见附录10 放电条件下的工作温度-20℃～55℃电池在规定的温度范围内能正常工作，容量损失在误差范围内。
11 存储温度短期（1个月内）-20℃～45℃长期（1年内）0℃～35℃12 存储湿度＜70﹪13 电池重量5250±50g5 测试条件5.1测试环境条件本规格书中各项试验应在标准大气条件下进行。
Product SpecificationFILE NAME： SPECIFICATIONS OFSEALED LiFePO 4 CYLINDRICAL BATTERIESMODEL： IFR14500MAB 600mAhSpecification No.: S/RONDA 0181-1EDITION： A3DATE： 2014-1-14EDITIONAMENDMENTDATE OF ISSUE AA0 Initial publishA1 1.Editing the parameters of IR and the weight2.Editing the parameters of the diameter and the heightA2 Editing the parameters of charge and discharge temperature A3 Editing the parameter of IR2008-11-05 2012-07-182013-11-112014-1-14DrawnCheckedReviewedApprovedNotice: If the document wasn’t signed and stamped, the information (subject to change without prior notice) contained in this document is for reference only and should not be used as a criterion for product guarantee or warranty.Product SpecificationIFR14500MAB 600mAh 1. SCOPEThe specification governs the performance of the following RONDA LiFePO4 Cylindrical cell and its battery pack. (Refer to the attached figure 1 )Rated capacity: 600mAhDesignation: IFR14500 (D: 13.90±0.2mm H: 48.50±0.5mm)Figure 1- Jacketed LiFePO4 cylindrical cells2. DATA OF BATTERY PACKThe data of battery pack, including voltage and weight, is almost equivalent to the multiple numbers of the relevant single cells.Example: Battery pack consisting three single cellsNominal voltage of single cell = 3.2VNominal voltage of battery pack = 3.2V×3 = 9.6V3. RATINGSTable 1 - Ratings of the cellsDescription Unit Specification Remark Nominal Voltage V 3.2 Single cellMax. Charge Voltage V 3.7 Single cellDischarge cut-off Voltage V 2.0 Single cellMax. constant charge current mA 600(1.0ItA) /Max. constant discharge current mA 1200(2.0ItA) /Rated Capacity mAh 600Charge with 0.2ItA to3.7V,then charge withconstant voltage till thecharge current is less than0.01ItA，and rest for 60 min,discharge with constantcurrent 0.2ItA to 2.0V.Operation Temp. ℃Charge:0~+40Discharge:-10~+40/Storage Temp. ℃ -10~+45 /within one monthWeightgAbout 18.0 For reference onlyStorage Voltage V3.20~3.40Product SpecificationIFR14500MAB 600mAh4. PERFORMANCE AND TEST METHODStandard charge method: Charge with constant current 0.2ItA to 3.7V/cell,and then charge withconstant voltage 3.7V,when the charge current is less than 0.01ItA,stop charging. Standard testing condition：Temp. 20±5℃Relative Humidity 65±20%RH (Unless otherwise stated)Table 2 – Performance and test methods bTest Item Unit SpecificationTest ConditionsRemarksDischarge performance 20 ah≥5After Standard Charge, stored for 1-2 hrs, then Discharge with 0.2ItA to 2.0V（25±2℃） Can be recycled for 5 times -10 h ≥3After Standard Charge, stored for 2h in -10±2℃, then discharged with 0.2I t A to 2.0V./55 h ≥4.5 After Standard Charge, stored for 2h in 55±2℃, then discharged by 0.2I t A to 2.0V./Charge (capacity)retention h/mi n≥4h15min After Standard Charge, stored on open circuit for a period of 28days in 20±5℃, then discharged with 0.2I t A to 2.0V./Endurance in cycles cycle ≥1000 Discharge with 0.2ItA to 2.0V, charge with 0.2ItA to 3.7V,then charge with 3.7V till the charge current less than 0.01ItA,stored for 10min,and move to next cycle, cycles should be repeated until the discharge capacity is less than 80% of normal capacity for three times. 20±2℃Internal resistance mΩ ≤55 50% Charged ,to measure in AC 1000Hz (20±2)℃/4.2 Safety performanceTest ItemSpecification Test conditionOvercharge testNo fire,No explosionDischarge with 0.2ItA to 2.0V, charge with 3ItA to5.0V,when the constant voltage get to 5.0V thecurrent is close to 0, last for 30min.Over-discharge testNo fire,No explosionAfter Standard charge, then discharge with 0.2ItAto 2.0V/cell, and then keeps on discharging for24h loaded with 30 Ω.S/RONDA 0181-1Heat Impact testNo fire,No explosionStandard charge first, then put the battery in the hot chamber, the temp. of chamber increased by 5±2℃ every min. till 130±2℃ keep for 10min.Product SpecificationIFR14500MAB 600mAh4.3.Reliability PerformanceTest Item SpecificationTest conditionHigh Temp. testElectric performance and appearance are free from affected Put the full charged battery in 70℃ for 2 hoursLow temp. testElectricperformanceandappearance are free fromaffectedPut the full charged battery in -10℃ for 2 hours，then stored in room temp. for 3 hours High Temp&High HumiditytestElectric performance and appearance are free from affected,including package.Put the full charged battery in the chamber of 40±2℃ 90-95%RH for 48 hours, then stored in 20±5℃ for 2 hours5. CONFIGURATION, DIMENSIONS AND MARKINGSPlease refer to the attached drawing. 6. EXTERNAL APPEARANCEThe cell/battery shall be free from cracks, scars, breakage, rust, discoloration, leakage nor deformation.6. Protection function requirementThe cell/battery shall be free from cracks, scars, breakage, rust, discoloration, leakage nor deformation.7. Protect requirement of batteryWhen Li-ion rechargeable battery is working under voltage/current which is higher than the specification stipulated, the electrolyte may be decomposed, which will affect the safety performance of the battery; the battery performance will be worsen if its voltage lower than 1.0V. In order to avoid overcharging, over-discharging or over-current ，please use right charger to charge the battery.To make sure safety, the charger and protect circuit should comply with following requirement:Object ItemRequirement RemarksCharger Charge cut-off Voltage (3.700~4.200)±0.049V / Protect Circuit （For reference only） Overcharge protect Voltage (3.700~4.200)±0.025V / Overcharge recover Voltage (3.700~4.200)±0.050V/ Discharge cut-off Voltage2.0±0.10V/S/RONDA 0181-1Over-discharge protect Voltage 2.0±0.08V/Over-discharge recover Voltage 2.0±0.10V /Over-current protect Value 2.0±0.2A / Note The above parameter is for reference only, customers could decide to adopt or change according to the practical situation.Product SpecificationIFR14500MAB 600mAh 8. Period of warranty12 months from manufacture date9. Disclaimer clauseFire or explosion will happen in case misuse of battery. So please comply with Ronda specification and caution in the document. Ronda will take no responsibility for any accident when the cell is used under other conditions than those described in this Document.10. Caution in use1）Do not immerse the cell in water, it should be kept in dry;2）Do not use/expose the cell to extreme heat or flame;3）Use the special Li-ion charger to charge the cell;4）Do not reverse the polarity of the cell for any reason;5）Do not connect cell to the plug socket or car-cigarette-plug;6）Do not throw the cell into heater or fire;7）Do not connect the cell with metal directly;8）Do not handle or store with metallic like necklaces, coins or hairpins, etc.9）Do not strike the cell by hammer or tread it.10）Do not make the direct soldering onto a cell or drive a nail into the cell;11）Do not use or leave the cell in high temp.(under the blazing sun or in heated car by sunshine),to avoid fire, disabled or life shorter of the cell;12）Do not use the cell under strong static or magnetic field, to avoid destroying of the protect device;13）If the electrolyte came into the eyes, do not rub, you should wash with water and contact a doctor at once;S/RONDA0181-114）If find any peculiar smell, heat, color change, distortion of the cell or there is any abnormity in using, storing or charging process, you should take it from the device or charger and stop its use;15）To avoid bad contact or function disabled, please use a dry cloth to clean the battery if it is dirty;16）Wasted cells should be packed with a insulated paper, to avoid fire or explosion.Product SpecificationIFR14500MAB 600mAh Base Data:Nominal voltage 3.2VCapacity comparison(mAh)0.2I t A 1.0I t A600 570Weight(g) 18.0Internal Impedance at 1000Hz(After Charge;m )≤55Charge currentStandard 120mAFast 600mACharge timeStandard /Fast /D 13.90±0.2mmAmbient Temperature charge Standard 0~+40℃H 48.50±0.5mm Fast +10~+40℃Discharge -10~+40℃Storage -10~+45℃S/RONDA0181-1this document is for reference only and should not be used as a criterion for product guarantee or warranty.产品规格书文件名称 圆柱型磷酸铁锂电池规格书 型 号 IFR14500MAB 600mAh 编 号 S/RONDA0181-1 版 次 A3日 期2014年1月14日版 次 修 改 内 容生 效 日 期 AA0 初版发行A1 1.修订电池内阻参数和重量 2.修订电池外径参数和高度 A2 修订充电和放电温度 A3 修订电池内阻参数2008-11-05 2012-07-182013-11-11 2014-1-14S/RONDA 0181-2草 拟审 核复 核批准如果文件没有签名并盖章，本文件中包含的信息仅供参考，不应被用来作为产品提供保证或担保的基准。
