201. Refer to the output from the show running-config command in the exhibit. What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address?
A. Apply access-group 14 to interface FastEthernet 0/0.
B. Add access-list 14 permit any any to the access list configuration.
C. Configure the IP address of the FastEtherent 0/0 interface to 10.90.201.1.
D. Add an interface description to the FastEthernet 0/0 interface configuration.
Answer: C
202. A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOSimage. What function does the router perform next?
A. It checks the configuration register.
B. It attempts to boot from a TFTP server.
C. It loads the first image file in flash memory.
D. It inspects the configuration file in NVRAM for boot instructions.
Answer: A
203. Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.
Answer: ACE
204. An access list has been designed to prevent HTTP traffic from the Accounting Department from reaching the HR server attached to the Holyoke router. Which of the following access lists will accomplish this task whengrouped with the e0 interface on the Chicopee router?
A. permit ip any any
deny tcp 172.16.16.0 0.0.0.255 172.17.17.252 0.0.0.0 eq 80
B. permit ip any any
deny tcp 172.17.17.252 0.0.0.0 172.16.16.0 0.0.0.255 eq 80
C. deny tcp 172.17.17.252 0.0.0.0 172.16.16.0 0.0.0.255 eq 80
permit ip any any
D. deny tcp 172.16.16.0 0.0.0.255 172.17.17.252 0.0.0.0 eq 80
permit ip any any
Answer: D
205. Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request?
A. The Mac address of the NIC in Sever1
B. The IP address of Server 1.
C. The MAC address of the s0/0/0 interface of router R2
D. The IP address of the s0/0/0 interface of router R1
E. The IP address of the Fa0/0 interface of router R1
Answer: B
206. Host 1 sends an ICMP echo request to remote sever1. Which destination address does Host 1 place in the Layer2 header of the frame containing the ping packet?
A. The IP address of sever 1.
B. The MAC address of NIC in sever 1.
C. The IP address of F0/0 interface of router R1.
D. The MAC address of the Fa0/0 interface of router R1.
E. The IP address of the s0/0/0 interface of router R2
F. The MAC address of the s0/0/0 interface of router R2
Answer: D
207. R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1?
A. The frame does not have MAC addresses.
B. The source MAC address in the frame is the MAC address of the NIC of Host 1.
C. The source MAC address in the frame is the MAC address of the s0/0/0 interface of R1.
D. The destination MAC address in the frame is the MAC address of the NIC of server 1.
E. The destination MAC address in the frame is the MAC address of the s0/0/0 interface of R2
Answer: A
208. Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1?
A. The MAC address of the NIC in Host 1 .
B. The MAC address of the NIC in server 1.
C. The MAC address of the Fa0/0 interface of router R1
D. The MAC address of the s0/0/0 interface of the router R2
Answer: C
209. Host 1 has just started up and requests a web page from web server 2. Which two statements describe steps in the process Host 1 uses to send the request to web server 2 (choose two)?
A. Host 1 addresses the frames to the MAC address of router R1
B. Host 1 looks in its ARP cache for the MAC address of router R1
C. Host 1 addresses the frames to the MAC address of web server 2
D. Host 1 sends the packets to router R1 to be forwarded to web server 2
E. Host 1 sends a broadcast ARP request to obtain the MAC address of webserver2.
Answer: CE
210. Refer to the exhibit.
Which two statements about the configuration of the switch interface are correct? (Choose two)
A. The switchport belongs only to VLAN 2
B. Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2
C. The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2
D. A network host can be connected to this interface.
Answer: AD
211. A TCP/IP transfer is diagrammed in the exhibit. A window size of three has been negotiated for this transfer. Which message will be returned from the
receiver to the sender as part of this TCP/IP transfer?
A. send ACK 1-3
B. send ACK 3
C. send ACK 4
D. send ACK 4-6
E. send ACK 6
F. send ACK 7
Answer: C
212. Three access points have been installed and configured to cover a small office. What term defines thewireless topology?
A. BSS
B. IBSS
C. ESS
D. SSID
Answer: C
213. Refer to the exhibit. Which two statements are true of the interfaces on Switch1? (Choose two.)
A. Multiple devices are connected directly to FastEthernet0/1.
B. A hub is connected directly to FastEthernet0/5.
C. FastEthernet0/1 is connected to a host with multiple network interface cards.
D. FastEthernet0/5 has statically assigned MAC addresses.
E. FastEthernet0/1 is configured as a trunk link.
F. Interface FastEthernet0/2 has been disabled.
Answer: BE
214. Refer to the exhibit. The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward the Internet over the most direct pathavailable. What configuration on the Manchester router will establish a route toward the Internet for traffic thatoriginates from workstations on the Manchester LAN?
A. ip route 0.0.0.0 255.255.255.0 172.16.100.2
B. ip route 0.0.0.0 0.0.0.0 128.107.1.1
C. ip route 0.0.0.0 255.255.255.252 128.107.1.1
D. ip route 0.0.0.0 0.0.0.0 172.16.100.1
E. ip route 0.0.0.0 0.0.0.0 172.16.100.2
F. ip route 0.0.0.0 255.255.255.255 172.16.100.2
Answer: E
215. Refer to the exhibit. An organization connects two locations, supporting two VLANs, through two switchesas shown. Inter-VLAN communication is not required. The network is working properly and there is fullconnectivity. The organization needs to add additional VLANs, so it has been decided to implement VTP. Bothswitches are configured as VTP servers in the same VTP domain. VLANs added to Switch1 are not learned bySwitch2. Based on this information and the partial configurations in the exhibit, what is the problem?
A. Switch2 should be configured as a VTP client.
B. VTP is Cisco proprietary and requires a different trunking encapsulation.
C. A router is required to route VTP advertisements between the switches.
D. STP has blocked one of the links between the switches, limiting connectivity.
E. The links between the switches are access links.
Answer: E
216. Refer to the exhibit. What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)
A. The number of collision domains would remain the same.
B. The number of collision domains would decrease.
C. The number of collision domains would increase.
D. The number of broadcast domains would remain the same.
E. The number of broadcast domains would decrease.
F. The number of broadcast domains would increase.
Answer: CD
217. Refer to the exhibit. Router4 can ping Router5 (172.16.6.5), but not Router7 (172.16.11.7). There are norouting protocols running in any of the routers, and Router4 has Router6 as its default gateway. What can be doneto address this problem?
A. Convert to static NAT.
B. Convert to dynamic NAT.
C. Add a static route in Router7 back to Router4.
D. Change the inside and outside NAT commands.
Answer: C
218. Which two statements describe the Cisco implementation of VLANs? (Choose two.)
A. VLAN 1 is the default Ethernet VLAN.
B. CDP advertisements are only sent on VLAN 1002.
C. By default, the switch IP address is in VLAN 1005.
D. VLANs 1002 through 1005 are automatically created and cannot be deleted.
Answer: AD
219. How does a DHCP server dynamically assign IP addresses to hosts?
A. Addresses are permanently assigned so that the host uses the same address at all times.
B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.
C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.
D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Answer: C
220. What is the purpose of the Cisco VLAN Trunking Protocol?
A. to allow traffic to be carried from multiple VLANs over a single link between switches
B. to allow native VLAN information to be carried over a trunk link
C. to allow for managing the additions, deletions, and changes of VLANs between switches
D. to provide a mechanism to manually assign VLAN membership to switch ports
E. to provide a mechanism to dynamically assign VLAN membership to switch ports
Answer: C
221. Refer to the exhibit. What statement is true of the configuration for this
network?
A. The configuration that is shown provides inadequate outside address space for translation of the number ofinside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support theNAT configuration as shown.
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Answer: C
222. What is the purpose of using the traceroute command?
A. to map all the devices on a network
B. to display the current TCP/IP configuration values
C. to see how a device MAC address is mapped to its IP address
D. to see the path a packet will take when traveling to a specified destination
E. to display the MTU values for each router in a specified network path from a source to a destination
Answer: D
223. Refer to the exhibit. The switches on a campus network have been interconnected as shown. All of theswitches are running Spanning Tree Protocol with its default settings. Unusual traffic patterns are observed and itis discovered that Switch9 is the root bridge. Which change will ensure that Switch1 will be selected as the rootbridge instead of Switch9?
A. Lower the bridge priority on Switch1.
B. Raise the bridge priority on Switch1.
C. Lower the bridge priority on Switch9.
D. Raise the bridge priority on Switch9.
E. Disable spanning tree on Switch9.
F. Physically replace Switch9 with Switch1 in the topology.
Answer: A
224. What is the purpose of an ARP request message?
A. It binds the IP address of a host to the network that it is on.
B. It builds a correlation between an IP address and a MAC address.
C. It provides connectivity and path selection between hosts on a network.
D. It encapsulates the Layer 3 address and then passes the packet to Layer 2.
E. It creates a session by passing a header with the destination Layer 2 address to the transport layer.
Answer: B
225. Refer to the exhibit. The network manager is evaluating the efficiency of the current network design. RIPv2 is enabled on all Layer 3 devices in the network. What network devices participate in passing traffic from the PCat 10.10.1.7 to File Server at 10.20.1.6 in the order that they will forward traffic from source to destination?
A. Switch1, Switch2
B. Switch1, Switch2, Router2, Switch2
C. Switch 1, Router1, Switch1, Switch2
D. Switch1, Router1, Router2, Switch2
Answer: D