Microcontroller Integrated Circuit with Read Only Memory
Microcontroller integrated circuit comprises a processor core which exchanges data with at least one data processing and storage device. The integrated circuit comprises a mask-programmed read only memory containing a generic program such as a test program which can be executed by the microcontroller. The genetic program includes a basic function for writing data into the data progressing or storage device or devices. The write function is used to load a downloading program. Because a downloading program is not permanently stored in the read only memory, the microcontroller can be tested independently of the application program, and remains standard with regard to the type of memory component with which it can be used in a system.
To be more precise, the invention concerns a microcontroller integrated circuit. A microcontroller is usually a VLSI (Very Large Scale Integration) integrated circuit containing all or most of the components of a "computer". Its function is not predefined but depends on the program that it executes.
A microcontroller necessarily comprises a processor core including a command sequencer (which is a device distributing various control signals to the instructions of a program), an arithmetic and logic unit (for processing the data) and registers (which are specialized memory units).
The other components of the "computer" can be either internal or external to the microcontroller, however. In other words, the other components are integrated into either the microcontroller or auxiliary circuits.
These other components of the "computer" are data processing and storage devices, for example read only or random access memory containing the program to be executed, clocks and interfaces (serial or parallel).
As a general rule, a system based on a microcontroller therefore comprises a microchip containing the microcontroller, and a plurality of microchips containing the external data processing and storage devices which are not integrated into the microcontroller. A microcontroller-based system of this kind comprises, for example, one or more printed circuit boards on which the microcontroller and the other components are mounted.
It is the application program, I. e. the program which is executed by the microcontroller, which determines the overall operation of the microcontroller system.
Each application program is therefore specific to a separate application.
In most current applications the application program is too large to be held in the microcontroller and is therefore stored in a memory external to the microcontroller. This program memory, which has only to be read, not written, is generally a reprogrammable read only memory (REPROM).
After the application program has been programmed in memory and then started in order to be executed by the microcontroller, the microcontroller system may not function as expected.
In the last unfavorable situation this is a minor dysfunction of the system and the microcontroller is still able to dialog with a test station via a serial or parallel interface. This test station is then able to determin the nature of the problem and indicates precisely the type of correction (software and physical) to be applied to the system for it to operate correctly.
Unfortunately, most dysfunctions of microcontroller-based system result in a total system lock-up, preventing any dialog with a test station. It is then impossible to determine the type of fault, i.e. whether it is a physical fault (in the microcontroller itself, in an external read only memory, in a peripheral device, on a bus, etc) or a software fault(i.e. an error in the application program).The troubleshooting technique usually employed in these cases of total lock-up is based on the use of sophisticated test devices requiring the application of probes to the pins of the various integrated circuits of the microcontroller-based system under test.
There are various problems associated with the use of such test devices for troubleshooting a microcontroller-based system. The probes used in these test devices are very fragile, difficult to apply because of the small size of the circuit and their close packing, and may not make good contact with the circuit.
Also, because of their high cost, these test devices are not mass produced. Consequently, faulty microcontroller-based systems can not be repaired immediately, wherever they happen to be located at the time, but must first be returned to a place where a test device is available. Troubleshooting a microcontroller-based system in this way is time-consuming, irksome and costly.
To avoid the need for direct action on the microcontroller-based system each time the application program executed by the microcontroller of the system is changed, it is standard practice to use a downloadable read only memory to store the application program, a loading program being written into a mask-programmed read
only memory of the microcontroller. The mask-programmed read only memory of the microcontroller is integrated into the microcontroller and programmed once and for all during manufacture of the microcontroller.
To change the application program the microcontroller is reset by running the downloading program. This downloading program can then communicate with a workstation connected to the microcontroller by an appropriate transmission line, this workstation the new application program to be written into the microcontroller. The downloading program receives the new application program and loads it into a read only memory external to the microcontroller.
Although this solution avoids the need for direct action on the microcontroller-based system (which would entail removing from the system the reprogrammable read only memories containing the application program, writing into these memories the new application program using an appropriate programming device and then replacing them in the system), it nevertheless has a major drawback, namely specialization of the microcontroller during manufacture.
Each type of reprogrammable memory is associated with a different downloading program because the programming parameters (voltage to be applied, duration for which the voltage is to be applied) vary with the technology employed. The downloading program is written once and for all into the mask-programmed internal memory of the microcontroller and the latter is therefore restricted to using memory components of the type for which this downloading program was written. In other words, the microcontroller is not a standard component and this increases its cost of manufacture.
One object of the invention is to overcome these various drawbacks of the prior art. To be more precise, an object of the invention is to provide a microcontroller circuit which can verify quickly, simply, reliably and at low cost the operation of a system based on the microcontroller.
Another object of the invention is to provide a microcontroller integrated circuit which can accurately locate the defective component or components of a system using the microcontroller in the event of dysfunction of the system.
A further object of the invention is to provide a microcontroller integrated circuit which avoids the need for direct action on the microcontroller-based system to change the application program, whilst remaining standard as regards the type of memory component with which it can be used in a system.
带有只读存储器的单片机集成电路
单片机集成电路包含一个处理器内核，它至少通过一种数据处理或存储设备来交换数据。集成电路包含一个只读掩模程序存储器，其中像测试程序一样的通用程序能被单片机执行。这种通用程序具有将数据写到数据处理和、或存储设备的基本功能。写入功能用于装载程序。因为装载程序并非永久地存储在只读存储器中，所以可对单片机进行测试，而与应用程序无关，并保持系统中能用的存储器元件为标准类型。
准确地说，这项发明涉及单片机集成电路。单片机通常是包含一台“计算机”的全部或大部分元件的大规模集成电路，其功能不是预先确定的，而是取决于它执行的程序。
一台单片机必然包含一个含有命令时序发生器（即根据程序的指令分配各种控制信号到其他元件的装臵）的处理器内核，一个算数逻辑单元（用来处理数据）和寄存器（即特殊的存储单元）。
然而，“计算机”的其他单元对单片机而言或是内部的，或是外部的。换言之，其他元件就集成到单片机或辅助电路中。
“计算机”的这些其他元件是数据处理或存储装臵，例如包含待执行程序的只读或随机存储器、时钟和接口（串行或并行）。
基于单片机的系统通常包含一个含有单片机的芯片和许多含有外部数据处理和、或存储器的芯片，这些芯片没有集成在单片机中。例如，这种基于单片机的系统包含一个或多个印刷电路板，上面安装着单片机和其他元件。
决定单片机所有操作的是应用程序，即由单片机执行的程序。因此，每个应用程序都是针对特定的应用的。
在多数现实应用中，由于应用程序太大，单片机无法存储，因此就存储在单片机的外部存储器中。这种只读处而不能写入的程序存储器通常就是可编程只读存储器。
应用程序在写入到存储器中后就开始执行，以便由单片机来执行。单片机系统有可能不会像预期的那样工作。
在最不顺的情况下，这只是系统的小故障，单片机仍然能够通过串行或并行口与测试设备对话。测试设备就能够确定问题的性质，并准确的指出校正的类型（软件和硬件），将其应用到系统上，以便正确操作。
遗憾的是，基于单片机系统的多数故障导致整个系统死锁，阻止了任何与测试设备的对话。这样就不能确定错误类型时硬件错误（单片机本身，外部只读存储器、外围设备、总线等）还是软件错误（应用程序的错误）。在系统死锁的情
况下，采用的故障分析方法通常是以使用精密仪器测试设备为基础，因而要求将探测仪连接到处于测试中的单片机系统的各种集成电路的管脚上。
采用测试设备对于单片机的系统进行故障诊断，其相关问题还有很多。由于电路体积小，布线密集，而测试设备中使用的探针容易损坏，用起来很麻烦，就可能与电路接触不好。
此外由于成本高，这些测试设备不是批量生产。结果，出故障的单片机系统就不能直接及时修复，不管它们此时安装在何处，首先必须送到有测试设备的地方。单片机系统的这种故障诊断即费时又麻烦，成本也高。
在改变系统中单片机执行的应用程序时，为了避免直接在单片机系统上进行操作，常规的做法是用可下载的只读存储器来存储应用程序，即写入到单片机掩模ROM中的装载程序。单片机的掩模ROM集成到单片机中，并在生产单片机时一次性编程写入。
为了改变应用程序，单片机通过运行装载程序而重臵。这个装载程序能通过合适的传输线与连接到单片机的工作站通信，而工作站提供写入到单片机的新的应用程序。装载程序接收新的应用程序并存储到单片机的外部ROM中。
尽管这种方法避免了对单片机系统的直接操作（这需要从系统中取出包含应用程序的可编程只读存储器，并用合适的编程设备将新的应用程序写进存储器，然后换到系统中），但是它仍然有一个较大的缺点，即在生产中对单片机的特殊处理。
由于编程参数（编程电压，外加电压的持续时间等）随着采用的技术而变化，每一种可编程存储器以对应的装载程序密切相关。装载程序一次性写进单片机内部的掩模存储器中，存储器因而就限制为装载程序要写入的存储器类型。换而言之，单片机不是标准器件，这就增加了生产成本。
这一发明就是为了克服先前技术的各种缺点。准确的说，该发明的目的就是要提供一种单片机产品，以便快速、简单、可靠、低成本地验证单片机的操作。
这项发明的另一个目的是提供一种单片机芯片，在系统出现故障时，可以借助于单片机准确地定位系统中失效的器件。
这项发明的更高目的是提供一种单片机芯片，在系统中能使用的存储器为标准类型时，不用直接对单片机系统进行操作就可改变应用程序。
Lesson 1 力学的基本概念 1、词汇： statics [st?tiks] 静力学；dynamics动力学；constraint约束；magnetic [m?ɡ＇netik]有磁性的；external [eks＇t?:nl] 外面的, 外部的；meshing啮合；follower从动件；magnitude [＇m?ɡnitju:d] 大小；intensity强度，应力；non-coincident [k?u＇insid?nt]不重合；parallel [＇p?r?lel]平行；intuitive 直观的；substance物质；proportional [pr?＇p?:??n?l]比例的；resist抵抗，对抗；celestial [si＇lestj?l]天空的；product乘积；particle质点；elastic [i＇l?stik]弹性；deformed变形的；strain拉力；uniform全都相同的；velocity[vi＇l?siti]速度；scalar[＇skeil?]标量；vector[＇vekt?]矢量；displacement代替；momentum [m?u＇ment?m]动量； 2、词组 make up of由……组成；if not要不，不然；even through即使，纵然； Lesson 2 力和力的作用效果 1、词汇： machine 机器；mechanism机构；movable活动的；given 规定的，给定的，已知的；perform执行；application 施用；produce引起，导致；stress压力；applied施加的；individual单独的；muscular [＇m?skjul?]]力臂；gravity[ɡr?vti]重力；stretch伸展，拉紧，延伸；tensile[tensail]拉力；tension张力，拉力；squeeze挤；compressive 有压力的，压缩的；torsional扭转的；torque转矩；twist扭，转动；molecule [m likju:l]分子的；slide滑动; 滑行；slip滑，溜；one another 互相；shear剪切；independently独立地，自立地；beam梁；compress压；revolve (使)旋转；exert [iɡ＇z?:t]用力，尽力，运用，发挥，施加；principle原则, 原理，准则，规范；spin使…旋转；screw螺丝钉；thread螺纹； 2、词组 a number of 许多；deal with 涉及，处理；result from由什么引起；prevent from阻止，防止；tends to 朝某个方向；in combination结合；fly apart飞散； 3、译文： 任何机器或机构的研究表明每一种机构都是由许多可动的零件组成。这些零件从规定的运动转变到期望的运动。另一方面，这些机器完成工作。当由施力引起的运动时，机器就开始工作了。所以，力和机器的研究涉及在一个物体上的力和力的作用效果。 力是推力或者拉力。力的作用效果要么是改变物体的形状或者运动，要么阻止其他的力发生改变。每一种
电气实用英语汇编 一．电气名词Electric items 二．线路（母线、回路）Lines (Bus, circuits) 三．设备Equipments 四．保护、继电器Protection , relays 五．电气仪表Electric instruments 六．防雷Lightning protection 七．接地Grounding, earthing 八．室、所Room , Substation 九．电修车间设备Equipments of electric repair 十．材料Material 十一．图名Drawings, diagrams 十二．表头Tables 十三．标准图词汇Terms from standard DWG 一．电气名词Electric items 交（直）流Alternating (direct) current 短路电流Short-circuit current 起始次暂态短路电流Initial subtransient short-circuit current 冲击电流Impulse current 稳态短路电流Steady state short-circuit current 临界电流Critical current
切断电流Rupturing current 熔断电流Blow-out current 故障电流Fault current 计算电流Calculating current 极限有限电流Limit effective current 过电流Over current 逆电流Inverse current 整定电流Setting current 额定电流Rated current 电流密度Current density 短路电流最大有效值Maximumeffectivevalueofshort-circuitcurrent 高压High-voltage , High-tension 低压Low-voltage , Low-tension 计算电压Calculating voltage 激磁电压Exciting voltage 冲击电压Impulse voltage 临界电压Critical voltage 残留电压Residual voltage 击穿电压Puncture voltage 脉动电压Pulsating voltage 供电电压Supply voltage
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学（含税收学）Public Finance (including Taxation) 金融学（含保险学）Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law 法学Science of Law 法学理论Jurisprudence 法律史Legal History 宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence 民商法学(含劳动法学、社会保障法学) Civil Law and Commercial Law (including Science of Labour Law and Science of Social Security Law ) 诉讼法学Science of Procedure Laws
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important considerations in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems covering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11-and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
电气专业术语中英文对照(3) 红色障碍灯Red obstruction lamp for aviation 厂区道路照明灯Street lighting in plant area 路灯Street lamp 视孔灯Inspection hole lamp 立杆弯灯goose-neck post lamp , pole lamp 模拟报警信号Semigraph and alarm signal 自整角机Selsyn 励磁机Exciter 显示器Display 电位器Potentiometer
内电阻Internal resistance 固定电阻（器）Fixed resistance 脱扣Release , trip 分励Shunt trip 特殊失压脱扣器Special no-voltage release “或”开关放大器“Or” switch amplifier 制动器Brake 电容Capacitor 整流器Rectifier 镇流器Chock 分流器Shunt
油变阻器Oil immersed rheostat 频敏电阻器Frequency sensitive rheostat 滑线变阻器Sliding rheostat 蜂鸣器Buzzer 电机加热器Space heater (for motor) 空气断路器电机操作机构Motor operating mechanism for air circuit-breaker 可控硅励磁装置Silicon controlled rectifier excitation device 保护装置Protective device (element) 闪光装置Flashing device 接闪装置（避雷器）Lightning arrester
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient 求导derivation 定积分definite integral 不定积分indefinite integral 曲率curvature 偏微分partial differential 毛坯rough 游标卡尺slide caliper 千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant 逆矩阵inverse matrix 线性方程组linear equations 概率probability 随机变量random variable 排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss 轴线axes 余子式cofactor 逻辑电路logic circuit 触发器flip-flop 脉冲波形pulse shape 数模digital analogy 液压传动机构fluid drive mechanism 机械零件mechanical parts 淬火冷却quench 淬火hardening 回火tempering 调质hardening and tempering 磨粒abrasive grain 结合剂bonding agent 砂轮grinding wheel 后角clearance angle 龙门刨削planing 主轴spindle
基于单片机控制的光收发器设计 1 引言 在“三网合一”的推动下,光纤到户等光纤接入方案的应用日益广泛。在光进铜退的呼声下,光网络迅速发展。光收发器在光通信中起到光电、电光转换的作用，是光通信必不可少的器件。由于涉及到高速电路设计、精密机械加工和光学设计,光收发器的成本占据了光纤通信系统和的重要部分,而较高的光收发器价格成了制约光纤接入推广的瓶颈。进一步降低光收发器的成本将有利于光接入的应用推广，加快光进铜退的步伐。 光收发器主要由电路部分、光发送组件和光接收组件组成。其中电路部分又包括激光驱动、光接收信号放大和控制部分。目前市场上的光收发器的电路部分使用的是三个专用芯片。一直有公司在研究把激光驱动和接收信号放大电路集成在一个器件上,控制器使用普通的嵌入式处理器的方案。由于只使用一个专用芯片和一个通用芯片，这样就可以大幅降低电路部分的成本。ＰHYWORＫS 公司研制的PＨＹ1０76芯片就是一款这样的芯片。它主要针对1.２５Ｇｂpｓ到２.5Ｇbps的光收发器,具有外围电路简单，控制电路只需要普通的8位单片机就可以实现的特点。本文主要研究了PHY１076 的性能，选择了ATMEL 公司的ATＭEＧA88 单片机进行控制,设计出光收发器样品，并进行了性能测试,最终成功设计了1.25G 光收发器。 ２光收发器设计方案及工作原理讨论 光收发器在发展的过程中,有许多种不同的外形封装。ＳＦＰ(小型化可热插拔光收发一体模块）是目前在5Ｇｂpｓ以下速率中最先进的一种封装形式,具有小型化、可热插拔、功耗小、系统可集成度高以及能够进行数字诊断功能等特点。 本设计中使用激光驱动电路和光接收放大电路集成的PHY１076 作为专用芯片，使用ＡＴＭEL 的AVR 单片机ATＭEGA88 进行控制和实现DDＭ功能,加上相应的TOＳA(光发射组件）,ROSA(光接收组件)和结构件，设计了一款工作在1.25Gｂpｓ传输距离为10km 的ＳFP 光收发器。系统方框图如图1所示：
启动轴starting axle 启动齿轮starting gear 启动棘轮starting ratchet wheel 复位弹簧restoring, pull back spring 弹簧座spring seating 摩擦簧friction spring 推力垫圈thrust washer 轴挡圈axle bumper ring 下料filling 切断cut 滚齿机gear-hobbing machine 剪料机material-shearing machine 车床lathe 拉床broaching machine 垂直度verticality, vertical extent 平行度 parallelism同心度 homocentricity 位置度position 拉伤pulling damage 碰伤bumping damage 缺陷deficiency 严重缺陷severe deficiency 摩擦力friction 扭距twist 滑动glide 滚动roll 打滑skid 脱不开can’t seperate 不复位can’t restore 直径diameter M值= 跨棒距test rod span 公法线common normal line 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 机床machine tool 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 剪切shear 扭转twist 弯曲应力bending stress 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 电路circuit 半导体元件semiconductor element 拉孔broaching 装配assembling 加工machining 液压hydraulic pressure 切线tangent 机电一体化mechanotronics mechanical-electrical integration 稳定性stability 介质medium 液压驱动泵fluid clutch 液压泵hydraulic pump 阀门valve 失效invalidation 强度intensity 载荷load 应力stress 安全系数safty factor 可靠性reliability 螺纹thread 螺旋helix 键spline 销pin 滚动轴承rolling bearing 滑动轴承sliding bearing 弹簧spring 制动器arrester brake 十字结联轴节crosshead 联轴器coupling 链chain 皮带strap 精加工finish machining 粗加工rough machining 变速箱体gearbox casing 腐蚀rust 氧化oxidation 磨损wear 耐用度durability 机械制图 Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求 technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer
英文翻译 机械设计 一台完整机器的设计是一个复杂的过程。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。 Machine Design The complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge. 任何产品在设计时第一步就是选择产品每个部分的构成材料。许多的材料被今天的设计师所使用。对产品的功能，它的外观、材料的成本、制造的成本作出必要的选择是十分重要的。对材料的特性必须事先作出仔细的评估。 One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to today's designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations. 仔细精确的计算是必要的，以确保设计的有效性。在任何失败的情况下，最好知道在最初设计中有有缺陷的部件。计算（图纸尺寸）检查是非常重要的。一个小数点的位置放错，就可以导致一个本可以完成的项目失败。设计工作的各个方面都应该检查和复查。 Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked. 计算机是一种工具，它能够帮助机械设计师减轻繁琐的计算，并对现有数据提供进一步的分析。互动系统基于计算机的能力，已经使计算机辅助设计（CAD）和计算机辅助制造（CAM）成为了可能。心理学家经常谈论如何使人们适应他们所操作的机器。设计人员的基本职责是努力使机器来适应人们。这并不是一项容易的工作，因为实际上并不存在着一个对所有人来说都是最优的操作范围和操作
中国教育在线考研频道提供考研全方面信息指导及咨询服务，为您成功考研提供一切帮助。 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学（含税收学）Public Finance (including Taxation) 金融学（含保险学）Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law 法学Science of Law 法学理论Jurisprudence 法律史Legal History 宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence
High-speed milling High-speed machining is an advanced manufacturing technology, different from the traditional processing methods. The spindle speed, cutting feed rate, cutting a small amount of units within the time of removal of material has increased three to six times. With high efficiency, high precision and high quality surface as the basic characteristics of the automobile industry, aerospace, mold manufacturing and instrumentation industry, such as access to a wide range of applications, has made significant economic benefits, is the contemporary importance of advanced manufacturing technology. For a long time, people die on the processing has been using a grinding or milling EDM (EDM) processing, grinding, polishing methods. Although the high hardness of the EDM machine parts, but the lower the productivity of its application is limited. With the development of high-speed processing technology, used to replace high-speed cutting, grinding and polishing process to die processing has become possible. To shorten the processing cycle, processing and reliable quality assurance, lower processing costs. 1 One of the advantages of high-speed machining High-speed machining as a die-efficient manufacturing, high-quality, low power consumption in an advanced manufacturing technology. In conventional machining in a series of problems has plagued by high-speed machining of the application have been resolved. 1.1 Increase productivity High-speed cutting of the spindle speed, feed rate compared withtraditional machining, in the nature of the leap, the metal removal rate increased 30 percent to 40 percent, cutting force reduced by 30 percent, the cutting tool life increased by 70% . Hardened parts can be processed, a fixture in many parts to be completed rough, semi-finishing and fine, and all other processes, the complex can reach parts of the surface quality requirements, thus increasing the processing productivity and competitiveness of products in the market. 1.2 Improve processing accuracy and surface quality High-speed machines generally have high rigidity and precision, and other characteristics, processing, cutting the depth of small, fast and feed, cutting force low, the workpiece to reduce heat distortion, and high precision machining, surface roughness small. Milling will be no high-speed processing and milling marks the surface so that the parts greatly enhance the quality of the surface. Processing Aluminum when up Ra0.40.6um, pieces of steel processing at up to Ra0.2 ~ 0.4um.
一．电气名词Electric items 二．线路（母线、回路）Lines (Bus , circuits) 三．设备Equipments 四．保护、继电器Protection , relays 五．电气仪表Electric instruments 六．防雷Lightning protection 七．接地Grounding , earthing 八．室、所Room , Substation 九．电修车间设备Equipments of electric repair 十．材料Material 十一．图名Drawings , diagrams 十二．表头Tables 十三．标准图词汇Terms from standard DWG 一．电气名词Electric items 交（直）流Alternating (direct) current 短路电流Short-circuit current 起始次暂态短路电流Initial subtransient short-circuit current 冲击电流Impulse current 稳态短路电流Steady state short-circuit current 临界电流Critical current 切断电流Rupturing current 熔断电流Blow-out current 故障电流Fault current 计算电流Calculating current 极限有限电流Limit effective current 过电流Over current 逆电流Inverse current 整定电流Setting current 额定电流Rated current 电流密度Current density 短路电流最大有效值Maximum effective value of short-circuit current 高压High-voltage , High-tension 低压Low-voltage , Low-tension 计算电压Calculating voltage 激磁电压Exciting voltage 冲击电压Impulse voltage 临界电压Critical voltage
2、应力和应变 在任何工程结构中独立的部件或构件将承受来自于部件的使用状况或工作的外部环境的外力作用。如果组件就处于平衡状态,由此而来的各种外力将会为零,但尽管如此,它们共同作用部件的载荷易于使部件变形同时在材料里面产生相应的内力。 有很多不同负载可以应用于构件的方式。负荷根据相应时间的不同可分为: (a)静态负荷是一种在相对较短的时间内逐步达到平衡的应用载荷。 (b)持续负载是一种在很长一段时间为一个常数的载荷, 例如结构的重量。这种类型的载荷以相同的方式作为一个静态负荷; 然而,对一些材料与温度和压力的条件下,短时间的载荷和长时间的载荷抵抗失效的能力可能是不同的。 (c)冲击载荷是一种快速载荷(一种能量载荷)。振动通常导致一个冲击载荷, 一般平衡是不能建立的直到通过自然的阻尼力的作用使振动停止的时候。 (d)重复载荷是一种被应用和去除千万次的载荷。 (e)疲劳载荷或交变载荷是一种大小和设计随时间不断变化的载荷。 上面已经提到，作用于物体的外力与在材料里面产生的相应内力平衡。因此,如果一个杆受到一个均匀的拉伸和压缩，也就是说, 一个力,均匀分布于一截面,那么产生的内力也均匀分布并且可以说杆是受到一个均匀的正常应力,应力被定义为 应力==负载 P /压力 A, 因此根据载荷的性质应力是可以压缩或拉伸的,并被度量为牛顿每平方米或它的倍数。 如果一个杆受到轴向载荷，即是应力，那么杆的长度会改变。如果杆的初始长度L和改变量△L已知，产生的应力定义如下: 应力==改变长△L /初始长 L 因此应力是一个测量材料变形和无量纲的物理量 ,即它没有单位;它只是两个相同单位的物理量的比值。 一般来说,在实践中,在荷载作用下材料的延伸是非常小的, 测量的应力以*10-6的形式是方便的, 即微应变, 使用的符号也相应成为ue。 从某种意义上说，拉伸应力与应变被认为是正的。压缩应力与应变被认为是负的。因此负应力使长度减小。 当负载移除时，如果材料回复到初始的，无负载时的尺寸时，我们就说它是具有弹性的。一特定形式的适用于大范围的工程材料至少工程材料受载荷的大部分的弹性, 产生正比于负载的变形。由于载荷正比于载荷所产生的压力并且变形正比于应变, 这也说明,当材料是弹性的时候, 应力与应变成正比。因此胡克定律陈述, 应力正比于应变。 这定律服从于大部分铁合金在特定的范围内, 甚至以其合理的准确性可以假定适用于其他工程材料比如混凝土，木材，非铁合金。 当一个材料是弹性的时候，当载荷消除之后，任何负载所产生的变形可以完全恢复,没有永久的变形。