SYSTEM ID SYSTEM NAME SYSTEM ID is a unique name, five characters or
less, defined by the user.
SYSTEM NAME is a unique name, 16 characters or less, defined by the user.
The system ID and name display under the following conditions:
?The system is powered on.
?The power is off and active POST errors are displayed. This message is for information only. You can change the system ID and name in the System Setup program. E1000 FAIL SAFE, CALL SUPPORT Failsafe event.Capture the system
E1000 MISCONFIG. CALL SUPPORT System misconfiguration. Incorrect processors, missing VRMs etc. would cause this kind of error
E0000 OVRFLW CHECK LOG LCD overflow message. A maximum of three error messages can display sequentially on the LCD. The fourth message displays as the standard overflow message. Check the SEL for details on the events.
E0119 Temp PROC # Processor # temperature is out of acceptable temperature range. Troubleshoot System Cooling
E0119 Temp Planar System board temperature is out of acceptable temperature range Troubleshoot System Cooling
E0119 Temp Ambient System Ambient temperature is out of acceptable temperature range Troubleshoot System Cooling
E0212 VOLT BATT ROMB ROMB battery is out of acceptable voltage range Troubleshoot the ROMB battery first. If the problem still exists troubleshoot/replace the system planar. E0212 VOLT BATT CMOS Motherboard CMOS battery is out of acceptable voltage range. Troubleshoot the CMOS battery first. If the problem still exists troubleshoot/replace the system planar.
E0212 PROC VTT Processor VTT voltage is out of acceptable voltage
range. Troubleshoot/replace the system planar.
E0212 Volt PG 1 5V 1.5V voltage is out of acceptable voltage
range. Troubleshoot/replace the system planar.
E0212 Volt PG 1 8V 1.8V voltage is out of acceptable voltage
range. Troubleshoot/replace the system planar.
E0212 Volt PG 3 3V Processor VTT voltage is out of acceptable voltage range. 3.3V voltage is out of acceptable voltage range.
E0212 Volt PG 5 V 5V voltage is out of acceptable voltage range. Troubleshoot/replace the system planar.
E0212 Volt PG 1 8V Video Video 1.8V voltage is out of acceptable voltage
range. Troubleshoot/replace the system planar.
E0212 Volt PG 1 35V 1.35V voltage is out of acceptable voltage
range. Troubleshoot/replace the system planar.
E0276 PROC # STATUS Faulty or improperly installed processor Troubleshoot the
Processor
E0276 PROC # VCORE Processor # VCORE voltage is out of acceptable
range. Troubleshoot the processor core power supply (VRD)
E0276 VRM # PG VRM # voltage is out of acceptable range. Troubleshoot the VRMs
E0276 VCACHE # PG VCACHE # voltage is out of acceptable voltage
range. Troubleshoot the VCACHE VRM/VRDs
E0276 PS AC Current Power supply AC current is out of acceptable
range. Troubleshoot the system power supply
E0276 PS Over Current Power supply current is out of acceptable range. Troubleshoot the system power supply
E0412 RPM FAN Fan # RPM is out of acceptable range. Troubleshoot System Cooling
E0412 FAN Redundancy Lost FAN redundancy lost Troubleshoot System Cooling E0412 RPM Fan PS Blank Power supply fan RPM is out of acceptable
range. Troubleshoot System Cooling
E07F0 PROC # IERR Faulty or improperly installed processor. Troubleshoot the Processors first. If the problem still exist then troubleshoot the add-on cards and the system planar
E07FA PROC n THERMTRIP Specified processor is out of acceptable temperature range and has halted operation. Troubleshooting System Cooling. If the problem persists, ensure that the processor heat sinks are properly installed. The LCD continues to display this message until the system's power cable is disconnected and reconnected to the AC power source, or the SEL is cleared using either Server Assistant or the BMC Management
Utility.
E0780 PROC n PRESENCE Processor is not installed in socket n. Install a processor in socket n.
E0780 PROC # Config Err PROC # configuration error. Troubleshoot the Processor
E0780 PROC # Disabled Processor # is disabled. Troubleshoot the Processor
E0876 PS # Missing No power available from the specified power supply;specified power supply is improperly installed or faulty Troubleshoot the Power Supplies
E0876 PS # Status No power available from the specified power supply; specified power supply is improperly installed or faulty Troubleshoot the Power Supplies
E0876 PS # Predictive Power source for specified power supply is unavailable, or out of acceptable range. Is caused by either PS over temperature or PS failure.
E0876 PS # AC LOST Power source for specified power supply is unavailable, or out of acceptable range Check the AC power source for the specified power supply
E0876 PS # AC RANGE Power source for specified power supply is unavailable, or out of acceptable range. Check the AC power source for the specified power supply
E0876 PS # AC OUT OF RANGE - APPLY 200-240V Power supply # has incorrect AC voltage plugged in. Apply 200-240V AC voltage. PowerEdge 6850 only. Check the AC power source for the specified power supply
E0880 PS Redundancy Lost Power supply redundancy lost. One of the power
supplies were removed from the system.
EB10C ECC Uncorr Err
ECC Uncorr Err Bank # System memory uncorrectable ECC errors. (on memory bank
#) Troubleshoot the DIMMs on the specified memory banks
EB113 I/O Channel Chk System IO Channel Check Troubleshoot the system motherboard
EB113 PCI Parity Err PCI Parity Error Troubleshoot the expansion cards and if the problem still exists then troubleshoot the system motherboard.
EB113 PCI System Err PCI System Error Troubleshoot the expansion cards and if the problem still exists then troubleshoot the system motherboard.
EB113 PCIE Fatal Err PCIE Fatal Err Troubleshoot the expansion cards and if the problem still exists then troubleshoot the system motherboard.
EB113 PCIE Non Fatal Err PCIE Non Fatal Err Troubleshoot the expansion cards and if the problem still exists then troubleshoot the system motherboard.
EB113 Chipset Err Chipset Err Troubleshoot the processors first. If the problem still exists then troubleshoot the expansion cards and the system motherboard.
EB107 PROC Protocol Err Faulty or improperly installed processor or system
board. Troubleshoot the Processor
EB107 PROC Bus PERR Faulty or improperly installed processor or system
board. Troubleshoot the Processor
EB107 PROC Init Err Faulty or improperly installed processor or system
board. Troubleshoot the Processor
EB107 PROC Machine Chk Faulty or improperly installed processor or system board. Troubleshoot the Processor
EB107 PROC Hot Processor is out of acceptable temperature range and has halted operation. Troubleshooting System Cooling
EB10C Memory Hot Plug Fail BIOS Memory Hot Remove Fail 6850 only
E0D76 BP Drive # Drive # failure. Faulty or improperly installed hard drive or RAID controller Troubleshoot the Hard Drives
E0D76 1x2 Drive # Drive # in 1X2 backplane failure. Faulty or improperly installed hard drive or RAID controller (6850)Troubleshoot the Hard Drives in the Media Bay
E0D76 SCSI Connector SCSI cable is not connected. Troubleshoot the SCSI cables
I0000 BIB BMC unable to read BIOS Initial Block (BIB) Troubleshoot the system board.
IS000 Intrusion System cover has been removed Information only
IB110 SBE Log Disabled Single Bit Error Log Disabled Information only
IB110 Logging Disabled BIOS Logging Disabled Information only
IB110 Memory Spared Memory spare bank enabled. Information only
IB110 Memory Mirrored Memory mirroring enabled Information only
IB110 Memory RAID Memory RAID enabled Information only
IB110 Memory Added Card # BIOS Memory Hot Add (6850 only) Information only IB110 Memory Removed BIOS Memory Hot Remove (6850 only) Information only