附录A 英文文献
Final drive\Differential
All vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road.
Powerflow
The drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels.
This is accomplished by a pinion drive gear,which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels.
Fig 1 Drive axle
Rear-wheel drive
Rear-wheel-drive vehicles are mostly trucks, very large sedans and many sports car and coupe models. The typical rear wheel drive vehicle uses a front mounted engine and transmission assemblies with a driveshaft coupling the transmission to the rear drive axle. Drive in through the layout of the bridge, the bridge drive shaft arranged vertically in the same vertical plane, and not the drive axle shaft, respectively, in their own sub-actuator with a direct connection, but the actuator is located at the front or the back of the adjacent shaft of the two bridges is arranged in series. Vehicle before and after the two ends of the driving force of the drive axle, is the sub-actuator and the transmission through the middle of the bridge. The advantage is not only a reduction of the number of drive shaft, and raise the driving axle of the common parts of each other, and to simplify the structure, reduces the volume and quality.
Fig 2 Rear-wheel-drive axle
Some vehicles do not follow this typical example. Such as the older Porsche or Volkswagen vehicles which were rear engine, rear drive. These vehicles use a rear mounted transaxle with halfshafts connected to the drive wheels. Also, some vehicles were produced with a front engine, rear transaxle setup with a driveshaft connecting the engine to the transaxle, and halfshafts linking the transaxle to the drive wheels.
Differential operation
In order to remove the wheel around in the kinematics due to the lack of co-ordination about the wheel diameter arising from a different or the same rolling radius of wheel travel required, inter-wheel motor vehicles are equipped with about differential, the latter to ensure that the car driver Bridge on both sides of the wheel when in range with a trip to the characteristics of rotating at different speeds to meet the requirements of the vehicle kinematics.
Fig 3 Principle of differential
The accompanying illustration has been provided to help understand how this occurs.
1.The drive pinion, which is turned by the driveshaft, turns the ring gear.
2.The ring gear, which is attached to the differential case, turns the case.
3.The pinion shaft, located in a bore in the differential case, is at right angles to the axle shafts and turns with the case.
4.The differential pinion (drive) gears are mounted on the pinion shaft and rotate with the shaft .
5.Differential side gears (driven gears) are meshed with the pinion gears and turn with the differential housing and ring gear as a unit.
6.The side gears are splined to the inner ends of the axle shafts and rotate the shafts as the housing turns.
7.When both wheels have equal traction, the pinion gears do not rotate on the pinion shaft, since the input force of the pinion gears is divided equally between the two side gears.
8.When it is necessary to turn a corner, the differential gearing becomes effective and allows the axle shafts to rotate at different speeds .
Open-wheel differential on each general use the same amount of torque. To determine the size of the wheel torque to bear two factors: equipment and friction. In dry conditions, when a lot of friction, the wheel bearing torque by engine size and gear restrictions are hours in the friction (such as driving on ice), is restricted to a maximum torque, so that vehicles will not spin round. So even if the car can produce more torque, but also need to have sufficient traction to transfer torque to the ground. If you increase the throttle after the wheels slip, it will only make the wheels spin faster.
Fig 4 Conventional differential
Limited-slip and locking differential operation
Fig 5 Limited-slip differential
Differential settlement of a car in the uneven road surface and steering wheel-driven speed
at about the different requirements; but is followed by the existence of differential in the side car wheel skid can not be effective when the power transmission, that is, the wheel slip can not produce the driving force, rather than spin the wheel and does not have enough torque. Good non-slip differential settlement of the car wheels skid on the side of the power transmission when the issue, that is, locking differential, so that no longer serve a useful differential right and left sides of the wheel can be the same torque.
Limited-slip and locking differential operation can be divided into two major categories：
(1) mandatory locking type in ordinary differential locking enforcement agencies to increase, when the side of the wheel skid occurs, the driver can be electric, pneumatic or mechanical means to manipulate the locking body meshing sets of DIP Shell will be with the axle differential lock into one, thus the temporary loss of differential role. Relatively simple structure in this way, but it must be operated by the driver, and good roads to stop locking and restore the role of differential.
(2) self-locking differential installed in the oil viscosity or friction clutch coupling, when the side of the wheel skid occurs when both sides of the axle speed difference there, coupling or clutch friction resistance on the automatic, to make certain the other side of the wheel drive torque and the car continued to travel. When there is no speed difference on both sides of the wheel, the frictional resistance disappeared, the role of automatic restoration of differentials. More complicated structure in this way, but do not require drivers to operate. Has been increasingly applied in the car. About non-slip differential, not only used for the differential between the wheels, but also for all-wheel drive vehicle inter-axle differential/.
Gear ratio
The drive axle of a vehicle is said to have a certain axle ratio. This number (usually a whole number and a decimal fraction) is actually a comparison of the number of gear teeth on the ring gear and the pinion gear. For example, a 4.11 rear means that theoretically, there are 4.11 teeth on the ring gear for each tooth on the pinion gear or, put another way, the driveshaft must turn 4.11 times to turn the wheels once. The role of the final drive is to reduce the speed from the drive shaft, thereby increasing the torque. Lord of the reduction ratio reducer, a driving force for car performance and fuel economy have a greater impact. In general, the more reduction ratio the greater the acceleration and climbing ability, and relatively poor fuel economy. However, if it is too large, it can not play the full power of the engine to achieve the proper speed. The main reduction ratio is more Smaller ，the speed is higher, fuel economy is better, but the acceleration and climbing ability will be poor.
附录B 文献翻译
主减速器和差速器
所有的汽车都装有不同类型的主减速器和差速器来驱动汽车行驶。无论是前驱汽车，后驱汽车还是四轮驱动的汽车，对于将发动机的动力转化到车轮上差速器都是不可缺少的部件。
动力的传递
驱动桥必须把发动机的动力转一个直角后传递出去，但人对于前轮驱动汽车发动机输出的转矩与主减速器是在同一直线上的，但是发动机前置的后轮驱动的汽车发动机的动力必须以正确的角度传递出去，来驱动车轮。
图中所示是齿轮驱动的过程，即由一个相对小的齿轮驱动一个大齿轮（主动齿轮和从动齿轮），从动锥齿轮和差速器壳连接在一起，在半轴的根部有一对带有内花键的半轴齿轮，半轴齿轮和半轴通过花键来连接在一起。当差速器壳旋转时，就驱动内部的半齿轮转动从而使半轴转动，将转矩传给车轮。
后驱动桥
后轮驱动的车辆大多是卡车，大型轿车和大部分跑车。典型的后轮驱动的车辆使用前置发动机和变速箱总成将转矩传输到后轮驱动桥。多驱动桥汽车中，在贯通式驱动桥的布置中，各桥的传动轴布置在同一纵向铅垂平面内，并且各驱动桥不是分别用自己的传动轴与分动器直接联接，而是位于分动器前面的或后面的各相邻两桥的传动轴，是串联布置的。汽车前后两端的驱动桥的动力，是经分动器并贯通中间桥而传递的。其优点是，不仅减少了传动轴的数量，而且提高了各驱动桥零件的相互通用性，并且简化了结构、减小了体积和质量。
一些车辆不是这个典型的例子。如老式的保时捷或大众汽车引擎在汽车后面，是后轮驱动。这些车辆使用的后方安装驱动桥与半轴来驱动车轮。另外，一些车辆是前置引擎，后桥与传动轴连接发动机来驱动车轮。
差速器
为了消除由于左右车轮在运动学上的不协调而产生左右车轮外径不同或滚动半径不相等而要求车轮行程，汽车左右驱动轮间都装有差速器，后者保证了汽车驱动桥两侧车轮在行程不等时具有以不同速度旋转的特性，从而满足了汽车行驶运动学要求。
如图所示说明了其工作情况
1.主动齿轮转动，从而驱动从动齿轮。
2.从动齿轮将转矩作用于差速器壳，使其转动。
3.位于差速器壳中的行星齿轮以适当的角度和半轴齿轮接触，并随的差速器壳转动。
4.行星齿轮（驱动齿轮）和十字轴连接，和十字轴一起转动。
5.半轴齿轮（被驱动齿轮）和行星齿轮啮合并且和从动齿轮及差速器壳作为一个整体一起转动。
6.半轴齿轮的内花键和半轴端部饿花键接在一起随着差速壳一起转动。
7.当两侧车轮转速相同时，行星齿轮和半轴齿轮无相对运动，左右齿轮力矩平均分配。
8.当汽车转弯时差速器开始起作用，是两侧的半轴以不同的转速旋转。
开式差速器对每个车轮一般使用相同量的扭矩。确定车轮承受的扭矩大小的因素有两个：设备和摩擦力。在干燥的条件下，当摩擦力很大时，车轮承受的扭矩大小受发动机和挡位的限制，在摩擦力很小时（如在冰上行驶），限制为最大扭矩，从而使车轮不会打滑。所以，即使汽车可以产生较大扭矩，也需要足够的牵引力将扭矩传输到地面。如果在车轮打滑之后加大油门，只会使车轮更快地旋转。如果曾在冰上驾驶过，您可能知道加速的窍门：如果启动时挂在二挡或三挡而不是一挡，则由于变速器中的齿轮传动，车轮的扭矩会较小。这样更容易在不旋转车轮的情况下加速。如果其中一个驱动轮具有很好的摩擦力，而另一个却在冰上时，这是开式差速器存在的问题。防滑差速器
差速器很好的解决了汽车在不平路面及转向时左右驱动车轮转速不同的要求；但随之而来的是差速器的存在使得汽车在一侧驱动轮打滑时动力无法有效传输，也就是打滑的车轮不能产生驱动力，而不打滑的车轮又没有得到足够的扭矩。防滑差速器很好的解决了汽车在一侧车轮打滑时出现的动力传输的问题，也就是锁止差速器，让差速器不再起作用，左右两侧的驱动轮均可得到相同的扭矩。
防滑差速器主要可分为两大类：
（1）强制锁止式在普通差速器上增加强制锁止机构，当发生一侧车轮打滑时，驾驶员可通过电动、气动或机械的方式来操纵锁止机构，拨动啮合套将差速器壳与半轴锁成一体，从而暂时失去差速的作用。这种方式结构比较简单，但必须由驾驶员进行操作，并在良好路面上停止锁止，恢复差速器的作用。
（2）自锁式在差速器中安装粘性硅油联轴节或摩擦离合器，当发生一侧车轮打滑时，两侧半轴出现转速差，联轴节或离合器就自动发生摩擦阻力，使另一侧车轮得到
一定的扭矩而驱动汽车继续行驶。当两侧车轮没有转速差时，摩擦阻力消失，自动恢复差速器的作用。这种方式结构比较复杂，但不需要驾驶员进行操作。目前已越来越多地在汽车上得到应用。防滑差速器不仅用于左右车轮间的差速器，也用于全轮驱动汽车的轴间差速器中。
主减速比
驱动桥都有一定得主减速比，这个数字（通常是一个整数和一个小数）实际上是主减速器主动齿轮与从动齿轮的关系。例如，如果主减速比为4.11则说明从动齿轮的齿数是主动齿轮齿数的4.11倍，换句话说就是主动齿轮轴转动4圈车轮才转动1圈。
主减速器的作用是降低从传动轴传来的转速，从而增大扭矩。主减速器的减速比，对汽车的动力性能和燃料经济性有较大的影响。一般来说，主减速比越大，加速性能和爬坡能力较强，而燃料经济性比较差。但如果过大，则不能发挥发动机的全部功率而达到应有的车速。主减速比越小，燃料经济性较好，但加速性和爬坡能力较差。
商务英语口语900句中英文对照中文翻译 Unit 1希望与要求 Part 1 . 1. We'd like to express our desire to establish business relationship with you on the basis of quality, mutually benefit and exchange of needed goods . 我们希望在保证质量、互惠互利以及交易彼此需要的货物的基础上和你们建立业务关系。 2 .In order to extend our export business to your country we wish to enter direct business relations with you. 为了扩大我们在贵国的出口业务，我们希望和你们建立直接贸易关系。 3. Our hope is to establish mutually beneficial trading relations between us . 希望在我们之间能够建立互惠互利的贸易关系。 4. We looking forward to further extensions of pleasant business relations. 我们期待进一步保持愉快的业务关系。 5. It’s our hope to continue with considerable business dealing with you. 我们的希望是和你们保持可观的生意往来。 6. We looking forward to receiving your quotation very soon. 我们期待尽快收到你们的报价单。 7.I hope you see from the reduction that we are really doing our utmost. 我希望你能够看到我们事实上已经作出了最大程度的让价。 8.We hope to discuss business with you at your earliest convenience. 我们希望在你方便的时候和你洽谈业务。
附录A 英文文献 Drive axle/differential All vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road. Powerflow The drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels. This is accomplished by a pinion drive gear, which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels. Fig 1 Drive axle
毕业设计（论文）外文参考文献及译文 英文题目Component-based Safety Computer of Railway Signal Interlocking System 中文题目模块化安全铁路信号计算机联锁系统 学院自动化与电气工程学院 专业自动控制 姓名葛彦宁 学号 200808746 指导教师贺清 2012年5月30日
Component-based Safety Computer of Railway Signal Interlocking System 1 Introduction Signal Interlocking System is the critical equipment which can guarantee traffic safety and enhance operational efficiency in railway transportation. For a long time, the core control computer adopts in interlocking system is the special customized high-grade safety computer, for example, the SIMIS of Siemens, the EI32 of Nippon Signal, and so on. Along with the rapid development of electronic technology, the customized safety computer is facing severe challenges, for instance, the high development costs, poor usability, weak expansibility and slow technology update. To overcome the flaws of the high-grade special customized computer, the U.S. Department of Defense has put forward the concept：we should adopt commercial standards to replace military norms and standards for meeting consumers’demand [1]. In the meantime, there are several explorations and practices about adopting open system architecture in avionics. The United Stated and Europe have do much research about utilizing cost-effective fault-tolerant computer to replace the dedicated computer in aerospace and other safety-critical fields. In recent years, it is gradually becoming a new trend that the utilization of standardized components in aerospace, industry, transportation and other safety-critical fields. 2 Railways signal interlocking system 2.1 Functions of signal interlocking system The basic function of signal interlocking system is to protect train safety by controlling signal equipments, such as switch points, signals and track units in a station, and it handles routes via a certain interlocking regulation. Since the birth of the railway transportation, signal interlocking system has gone through manual signal, mechanical signal, relay-based interlocking, and the modern computer-based Interlocking System. 2.2 Architecture of signal interlocking system Generally, the Interlocking System has a hierarchical structure. According to the function of equipments, the system can be divided to the function of equipments; the system
https://www.doczj.com/doc/9d7601378.html,/finance/company/consumer.html Consumer finance company The consumer finance division of the SG group of France has become highly active within India. They plan to offer finance for vehicles and two-wheelers to consumers, aiming to provide close to Rs. 400 billion in India in the next few years of its operations. The SG group is also dealing in stock broking, asset management, investment banking, private banking, information technology and business processing. SG group has ventured into the rapidly growing consumer credit market in India, and have plans to construct a headquarters at Kolkata. The AIG Group has been approved by the RBI to set up a non-banking finance company (NBFC). AIG seeks to introduce its consumer finance and asset management businesses in India. AIG Capital India plans to emphasize credit cards, mortgage financing, consumer durable financing and personal loans. Leading Indian and international concerns like the HSBC, Deutsche Bank, Goldman Sachs, Barclays and HDFC Bank are also waiting to be approved by the Reserve Bank of India to initiate similar operations. AIG is presently involved in insurance and financial services in more than one hundred countries. The affiliates of the AIG Group also provide retirement and asset management services all over the world. Many international companies have been looking at NBFC business because of the growing consumer finance market. Unlike foreign banks, there are no strictures on branch openings for the NBFCs. GE Consumer Finance is a section of General Electric. It is responsible for looking after the retail finance operations. GE Consumer Finance also governs the GE Capital Asia. Outside the United States, GE Consumer Finance performs its operations under the GE Money brand. GE Consumer Finance currently offers financial services in more than fifty countries. The company deals in credit cards, personal finance, mortgages and automobile solutions. It has a client base of more than 118 million customers throughout the world
浅谈差速器 普通行星齿轮差速器由行星架（差速器壳），半轴齿轮等零件组成。它将发动机的动力，直接驱动差速器壳体内的轴，再由行星齿轮驱动左、右两半轴，并分别驱动左、右车轮。差速器的设计应满足：左半轴转速与右半轴转速之和等于两倍的行星架转速。当两侧车轮以纯滚动的形式做等距行驶时，会减少轮胎和路面的摩擦.差速器的这种调整是自动的，这里涉及到“最小能耗原理”，即地球上所有物体都倾向于耗能最小的状态。例如把一粒豆子放入一个碗内，豆子会自动停留在碗底，而不会留在碗壁，因为碗底是能量消耗最低的位置（位能），它会自动选择静止（动能最小）而不会不断地运动。同样的道理，汽车转弯时所有的驱动轮，左、右车轮与行星架的速度是相等的，而在汽车转弯时的三个平衡状态被破坏，导致内侧轮转速减小，横向轮RPM增加。 汽车差速器是驱动桥的主要部件。其功能是传递两侧半轴的动力，同时允许两半轴以不同的速度旋转，同时能够满足按照国家标准的自动的最低能量消耗的趋势，在转弯时自动接受转向半径来调整右轮转速，由于横向摩擦轮拖动现象，内侧车轮有滑动现象，现在两个驱动轮可以产生两个相反方向的附加力，因此符合最小的能源消耗原理, 这不可避免地导致了两侧车轮的速度差，从而摧毁了三个平衡关系，并通过半轴齿轮体现出来。迫使行星齿轮产生自转，使外侧半轴转速更快，内侧半轴减速，从而实现两侧车轮转速的差异。 如果任意一侧驱动轴上的驱动轮都使用一个整体的刚性连接，那么这两个轮子只能以相同的角度旋转。所以，当车辆的转向轮驱动时，由于外侧车轮比内侧车轮横过的距离大，将使外侧车轮在滚动的同时产生延迟，内侧车轮在滚动的同时产生滑动。即使车轮在凹凸不平的道路上跑直线，因为虽然道路是直，但轮胎滚动半径范围（轮胎制造误差，磨损不同，通过不均或气压不等所造成的车轮滑动）轮毂时，不仅会加剧轮胎的磨损滑动，增加动力性和燃油消耗，还能使车辆的转向困难，制动性能变得差.为了使车轮尽可能不会发生滑动的结构，必须保证车轮可以以不同的角度旋转。 轴间差速器：通常驾驶的轿车轮毂轴承支撑在主轴上，能够以任何角度旋转，驱动车轮分别与两根半轴刚性连接，在两根半轴之间有一个差速器，这种差速器称为轴间差速器。 如果使后轮轴成为一个整体，他将无法使两侧的车轮转速有差异，即不能做自动调整。为了解决这个问题，早在一百年前，法国雷诺汽车公司创始人路易斯·雷诺设计了一个差速器。 现代汽车上的差速器通常是根据其工作特性分为齿轮式差速器和限滑差速器两大类。 1.开模差速器 诺基开模差速器的结构是典型的行星齿轮组的结构，只有太阳轮和小齿轮环外
中英文对照翻译 (文档含英文原文和中文翻译) Policies for Development of Iron and Steel Industry The iron and steel industry is an important basic industry of the national economy, a supporting industry for realizing the industrialization and an intensive industry in technologies, capital, resources and energy, and its development requires a comprehensive balancing of all kinds of external conditions. China is a big developing country with a comparatively big demand of iron and steel in the economic development for a long time to go. China's production capacity of iron and steel has ranked the first place in the world for many years. However, there is a large gap in terms of the technological level and material consumption of the iron and steel industry compared with the international advanced level, so the focus of development for the future shall be put on technical upgrading and structural adjustment. In order to enhance the whole technical level of the iron and steel industry, promote the structural adjustment, improve the industrial layout, develop a recycling economy, lower the consumption of materials and energy, pay attention to the environmental protection, raise the comprehensive competitive capacity of enterprises, realize the industrial upgrading, and develop the iron and steel industry into an industry with
PLC论文中英文对照资料外文翻译文献 外文资料: PLC technique discussion and future development Along with the development of the ages, the technique that is nowadays is also gradually perfect, the competition plays more more strong; the operation that list depends the artificial has already can't satisfied with the current manufacturing industry foreground, also can't guarantee the request of the higher quantity and high new the image of the technique business enterprise. The people see in produce practice, automate brought the tremendous convenience and the product quantities for people up of assurance, also eased the personnel's labor strength, reduce the establishment on the personnel. The target control of the hard realization in many complicated production lines, whole and excellent turn, the best decision etc., well-trained operation work, technical personnel or expert, governor but can judge and operate easily, can acquire the satisfied result. The research target of the artificial intelligence makes use of the calculator exactly to carry out, imitate these intelligences behavior, moderating the work through person's brain and calculators, with the mode that person's machine combine, for resolve the very complicated problem to look for the best path We come in sight of the control that links after the electric appliances in various situation, that is already the that time generation past, now of after use in the mold a perhaps simple equipments of grass-roots control that the electric appliances can do for the low level only;And the PLC emergence also became the epoch-making topic, adding the vivid software control through a very and stable hardware, making the automation head for the new high tide. The PLC biggest characteristics lie in: The electrical engineering teacher already no longer electric hardware up too many calculationses of cost, as long as order the importation that the button switch or the importation of the sensors order to link the PLC up can solve problem, pass to output to order the conjunction contact machine or control the start equipments of the
驱动桥设计 随着汽车对安全、节能、环保的不断重视，汽车后桥作为整车的一个关键部件，其产品的质量对整车的安全使用及整车性能的影响是非常大的，因而对汽车后桥进行有效的优化设计计算是非常必要的。 驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩,并将动力合理地分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直力力和横向力。驱动桥一般由主减速器、差速器、车轮传动装置和驱动桥壳等组成。 驱动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载重汽车显得尤为重要。驱动桥设计应当满足如下基本要求： 1、符合现代汽车设计的一般理论。 2、外形尺寸要小，保证有必要的离地间隙。 3、合适的主减速比，以保证汽车的动力性和燃料经济性。 4、在各种转速和载荷下具有高的传动效率。 5、在保证足够的强度、刚度条件下，力求质量小，结构简单，加工工艺性 好，制造容易，拆装，调整方便。 6、与悬架导向机构运动协调，对于转向驱动桥，还应与转向机构运动协调。智能电子技术在汽车上得以推广使得汽车在安全行驶和其它功能更上一层楼。通过各种传感器实现自动驾驶。除些之外智能汽车装备有多种传感器能充分感知交通设施及环境的信息并能随时判断车辆及驾驶员是否处于危险之中，具备自主寻路、导航、避撞、不停车收费等功能。有效提高运输过程中的安全，减少驾驶员的操纵疲劳度，提高乘客的舒适度。当然蓄电池是电动汽车的关键，电动汽车用的蓄电池主要有：铅酸蓄电池、镍镉蓄电池、钠硫蓄电池、钠硫蓄电池、锂电池、锌—空气电池、飞轮电池、燃料电池和太阳能电池等。在诸多种电池中，燃料电池是迄今为止最有希望解决汽车能源短缺问题的动力源。燃料电池具有高效无污染的特性，不同于其他蓄电池，其不需要充电，只要外部不断地供给燃料，就能连续稳定地发电。燃料电池汽车(FCEV)具有可与内燃机汽车媲美的动力性能，在排放、燃油经济性方面明显优于内燃机车辆。
VOLUME 30 ISSUE 2 October 2008 Journal of Achievements in Materials and Manufacturing Engineering Copyright by International OCSCO World Press. All rights reserved.2008 151 Research paper 2008年十月期2卷30 材料与制造工程成果期刊 版权所有：国际OCSCO 世界出版社。一切权利保有。2008 ？？151研究论文 1. Introduction Friction stir welding (FSW) is a new solid-state welding method developed by The Welding Institute (TWI) in 1991 [1]. The weld is formed by the excessive deformation of the material at temperatures below its melting point, thus the method is a solid state joining technique. There is no melting of the material, so FSW has several advantages over the commonly used fusion welding techniques [2-10]. 1.导言摩擦搅拌焊接（FSW）是焊接学？会于1991年研发的一种新型固态焊接方法。这种焊接？是由材料在低于其熔点的温度上过量变形形成，因此此技术是一种固态连接技术。材料不熔化，所以FSW 相比常用的熔化焊接技术有若干优势。例如，在焊接区无多孔性或破裂，工件（尤其薄板上）没有严重扭曲，并且在连接过程中不需要填料、保护气及昂贵的焊接准备there is no significant distortion of the workpieces (particularly in thin plates), and there is no need for filler materials, shielding gases and costly weld preparation during this joining process. FSW被认为是对若干材料例如铝合金、镁合金、黄铜、钛合金及钢最显著且最有潜在用途的焊接技术FSW is considered to be the most remarkable and potentially useful welding technique for several materials, such as Al-alloys, Mg-alloys, brasses, Ti-alloys, and steels [1-16]. 然而，在FSW过程中，用不合适的焊接参数能引起连接处失效，并且使FSW连接处的力学性能恶化。However, during FSW process using inappropriate welding parameters can cause defects in the joint and deteriorate the mechanical properties of the FSW joints [2, 3]. 此技术起初就主要是为低熔点材料如铝合金、镁合金及铜合金而广泛研究的。The technique has initially been widely investigated for mostly low melting materials, such as Al, Mg and Cu alloys. 此技术已被证明是很有用的，尤其在连接用于航空航天用途的如高合金2XXX及7XXX系列铝合金等难熔高强度的铝合金。It has proven to be very useful, particularly in the joining of the difficult-to-fusion join high strength Al-alloys used in aerospace applications, such as highly alloyed 2XXX and 7XXX series aluminium alloys. 做出Al-5086 H32型板摩擦搅拌对焊的高强度、抗疲劳及断裂的力学性能？。The difficulty of making high-strength, fatigue and fracture resistant Mechanical properties of friction stir butt-welded Al-5086 H32 plate G. .am a,*, S. Gü.lüer b, A. .akan c, H.T. Serinda. a a Mustafa Kemal University, Faculty of Engineering and Architecture, 31040 Antakya, Turkey a 土耳其安塔卡亚31040，Mustafa Kemal大学建筑工程系 b General Directorate of Highways of Turkey, Ankara, Turkey b 土耳其安卡拉土耳其高速公路总理事会？ c Abant Izzet Baysal University, Faculty of Engineering an d Architecture, 14280 Bolu, Turkey c 土耳其Bolu 14280 Abant Izzet Baysal 大学建筑工程系 * Corresponding author: E-mail address: gurelcam@https://www.doczj.com/doc/9d7601378.html, *相关作者电子邮箱地址：gurelcam@https://www.doczj.com/doc/9d7601378.html, Received 30.06.2008; published in revised form 01.10.2008
Dashboard From Wikipedia, the free encyclopedia This article is about a control panel placed in the front of the car. For other uses, see Dashboard (disambiguation). The dashboard of a Bentley Continental GTC car A dashboard (also called dash, instrument panel (IP), or fascia) is a control panel located directly ahead of a vehicle's driver, displaying instrumentation and controls for the vehicle's operation. Contents 1.Etymology 2.Dashboard features 3.Padding and safety 4.Fashion in instrumentation 5.See also 6.References Etymology Horse-drawn carriage dashboard Originally, the word dashboard applied to a barrier of wood or leather fixed at the front of a horse-drawn carriage or sleigh to protect the driver from mud or other debris "dashed up" (thrown up) by the horses' hooves.[1] Commonly these boards did not perform any additional function other than providing a convenient handhold for ascending into the driver's seat, or a small clip with which to secure the reins when not in use. When the first "horseless carriages" were constructed in the late 19th century, with engines mounted beneath the driver such as the Daimler Stahlradwagen, the simple dashboard was retained to protect occupants from debris thrown up by the cars' front wheels. However, as car design evolved to position the motor in front of the driver, the dashboard became a panel that protected vehicle occupants from the heat and oil of the engine. With gradually increasing mechanical complexity, this panel formed a convenient location for the placement of gauges and minor controls, and from this evolved the modern instrument panel,
例1.Winners do not dedicate their lives to a concept of what they imagine they should be, rather, they are themselves and as such do not use their energy putting on a performance, maintaining pretence and manipulating（操纵） others . They are aware that there is a difference between being loved and acting loving, between being stupid and acting stupid, between being knowledgeable and acting knowledgeable. Winners do not need to hide behind a mask. 1.dedicate to 把时间，精力用于 2.pretence 虚伪，虚假 6 ．1 斤斤于字比句次，措辞生硬 例2.Solitude is an excellent laboratory in which to observe the extent to which manners and habits are conditioned by others. My table manners are atrocious( 丑恶)—in this respect I've slipped back hundreds of years in fact, I have no manners whatsoever（完全，全然）. If I feel like it, I eat with my fingers, or out of a can, or standing up —in other words, whichever is easiest. 孤独是很好的实验室，正好适合观察一个人的举止和习惯在多大程度上受人制约。如今我吃东西的举止十分粗野；这方面一放松就倒退了几百年，实在是一点礼貌也没有。我高兴就用手抓来吃，（eat out of a can）开个罐头端着吃，站着吃；反正怎么省事就怎么吃。 3.Whatsoever 完全，全然 1.Be conditioned by 受……制约 2.Atrocious 丑恶 6 ．2 结构松散，表达过于口语化 例3．有一次，在拥挤的车厢门口，我听见一位男乘客客客气气地问他前面的一位女乘客：“您下车吗？”女乘客没理他。“您下车吗？”他又问了一遍。女乘客还是没理他。他耐不住了，放大声问：“下车吗？”，那女乘客依然没反应。“你是聋子，还是哑巴？”他急了，捅了一下那女乘客，也引起了车厢里的人都往这里看。女乘客这时也急了，瞪起一双眼睛，回手给了男乘客一拳。（庄绎传，英汉翻译教程，1999 ：练习 3 ） 译文1：Once at the crowded door of the bus, I heard a man passenger asked politely a woman passenger before him: “Are you getting off?” The woman made no
中英文对照资料外文翻译文献 平设计任何时期平面设计可以参照一些艺术和专业学科侧重于视觉传达和介绍。采用多种方式相结合，创造和符号，图像和语句创建一个代表性的想法和信息。平面设计师可以使用印刷，视觉艺术和排版技术产生的最终结果。平面设计常常提到的进程，其中沟通是创造和产品设计。共同使用的平面设计包括杂志，广告，产品包装和网页设计。例如，可能包括产品包装的标志或其他艺术作品，举办文字和纯粹的设计元素，如形状和颜色统一件。组成的一个最重要的特点，尤其是平面设计在使用前现有材料或不同的元素。平面设计涵盖了人类历史上诸多领域，在此漫长的历史和在相对最近爆炸视觉传达中的第20和21世纪，人们有时是模糊的区别和重叠的广告艺术，平面设计和美术。毕竟，他们有着许多相同的内容，理论，原则，做法和语言，有时同样的客人或客户。广告艺术的最终目标是出售的商品和服务。在平面设计，“其实质是使以信息，形成以思想，言论和感觉的经验”。
在唐朝（618-906 ）之间的第4和第7世纪的木块被切断打印纺织品和后重现佛典。阿藏印在868是已知最早的印刷书籍。在19世纪后期欧洲，尤其是在英国，平面设计开始以独立的运动从美术中分离出来。蒙德里安称为父亲的图形设计。他是一个很好的艺术家，但是他在现代广告中利用现代电网系统在广告、印刷和网络布局网格。于1849年，在大不列颠亨利科尔成为的主要力量之一在设计教育界，该国政府通告设计在杂志设计和制造的重要性。他组织了大型的展览作为庆祝现代工业技术和维多利亚式的设计。从1892年至1896年威廉?莫里斯凯尔姆斯科特出版社出版的书籍的一些最重要的平面设计产品和工艺美术运动，并提出了一个非常赚钱的商机就是出版伟大文本论的图书并以高价出售给富人。莫里斯证明了市场的存在使平面设计在他们自己拥有的权利，并帮助开拓者从生产和美术分离设计。这历史相对论是，然而，重要的，因为它为第一次重大的反应对于十九世纪的陈旧的平面设计。莫里斯的工作，以及与其他私营新闻运动，直接影响新艺术风格和间接负责20世纪初非专业性平面设计的事态发展。谁创造了最初的“平面设计”似乎存在争议。这被归因于英国的设计师和大学教授Richard Guyatt，但另一消息来源于20世纪初美国图书设计师William Addison Dwiggins。伦敦地铁的标志设计是爱德华约翰斯顿于1916年设计的一个经典的现代而且使用了系统字体设计。在20世纪20年代，苏联的建构主义应用于“智能生产”在不同领域的生产。个性化的运动艺术在2俄罗斯大革命是没有价值的，从而走向以创造物体的功利为目的。他们设计的建筑、剧院集、海报、面料、服装、家具、徽标、菜单等。J an Tschichold 在他的1928年书中编纂了新的现代印刷原则，他后来否认他在这本书的法西斯主义哲学主张，但它仍然是非常有影响力。Tschichold ，包豪斯印刷专家如赫伯特拜耳和拉斯洛莫霍伊一纳吉，和El Lissitzky 是平面设计之父都被我们今天所知。他们首创的生产技术和文体设备，主要用于整个二十世纪。随后的几年看到平面设计在现代风格获得广泛的接受和应用。第二次世界大战结束后，美国经济的建立更需要平面设计，主要是广告和包装等。移居国外的德国包豪斯设计学院于1937年到芝加哥带来了“大规模生产”极简到美国;引发野火的“现代”