Cisco Campus ATM Solutions
Chapter 1 Course Introduction
?Sign-in sheet ?In-class questions ?Break times ?Lunch ?Telephone ?Smoking policy
Welcome to Cisco Training
Welcome to Cisco Training
?Name and company
?Job title and responsibilities
?Internetworking experience
?ATM experience
?Objectives
Course Agenda
?ATM technology
?ATM router interfaces
ATM lab 1
?LightStream 1010 and PNNI
ATM lab 2
?LAN Emulation (LANE) and MPOA ATM lab 3
Upon completion of this course, you will be able to:
?Describe the basics of ATM technology and its applications ?Explain Cisco's campus implementation of ATM
?Describe, enable, and configure the ATM interface on a router ?Describe, enable, and configure the Lightstream 1010 switch ?Describe Lightstream 1010 PNNI routing protocol
?Identify the Lightstream 1010 PNNI configuration commands ?Describe and configure LANE
?Describe LANE version 2.0 and MPOA
?Establish an ATM network in the lab that includes Lightstream 1010 and AIP/NPM
Course Objectives
Module 1–ATM Technology
?Introduction
Cisco ATM campus products
ATM introduction
?ATM lower layers
ATM physical layer
ATM layer
ATM adaptation layer ATM
Lower
Layers
Higher Layers
AAL
Physical
ATM
Module 1–ATM Technology (cont.)
?ATM higher layers
Signaling
Routing (PNNI)WAN internetworking Circuit emulation
LAN emulation Native mode protocol
RFC 1483, RFC 1577, NHRP, MPOA ATM network management
ATM Higher Layers
AAL Physical
ATM Higher Layers
Module 2–AIP, NPM, and ATM-CES PA
?Features and functions (AIP/NPM)
Physical interfaces support
Traffic management
Encapsulation types
?ATM-CES-PA on Cisco 7200 router series ?Configuration
PVC, SVC, QoS
NPM configuration examples
?Hands-on lab
?Review of the lab
Module 3–LightStream 1010?LS1010 features and functions
Switch applications, components, and architecture
Connection and traffic management functions
Network management
?LS1010 configuration
PVC, PVP, and Soft PVC, SVC
Autoconfiguration
show commands
?LS1010 PNNI features, functions and configuration ?Hands-on lab
?Review of the lab
Module 4–LAN Emulation
?VLAN/LANE overview
?LANE components
?LANE VCCs
?LANE operation
?LANE configuration
?Cisco SSRP
?show and debug commands
?Hands-on lab
?Review of the lab
Module 4–LANE 2.0 and MPOA
?LANE 2.0
–LANE 1.0 limitation
–LUNI 2.0 and LNNI
–LANE 2.0 multicasting
?MPOA
–MPOA building blocks
–MPOA architecture
–Data transfer
–Operation
ATM Labs
?The components used in the lab: LightStream 1010 switch
Cisco 7000 series routers/AIP
Cisco 4500 series routers/NPM
Duplex SC connector
Multi-and single-mode fiber cable
Graphic Symbols
FastHub
Catalyst
Switch
ATM
Switch
Bridge
Router
PC
Firewall
SwitchProbe
Server
10BaseT
Hub
FDDI
Dual Ring Token Ring
Multilayer
Switch
Si
Multiswitch
Device
ATM Network
Common ATM Acronyms
AAL—ATM Adaptation Layer
ABR—Available Bit Rate
API—Application Programmer Interface
B-ICI—B-ISDN Inter-Carrier Interface
BUS—Broadcast and Unknown Server
CAC—Connection Admission Control
CBR—Constant Bit Rate
CCITT—Consultative Committee for International Telephony and Telegraph
CDVT—Cell Delay Variation Tolerance
CLP—Cell Loss Priority
CLR—Cell Loss Ratio
CS—Convergence Sublayer
EFCI—Explicit Forward Congestion Indicator
ELAN—Emulated LAN
GCRA—Generic Cell Rate Algorithm
GFC—Generic Flow Control
HEC—Header Error Check
IISP—Interim Inter-Switch Signaling Protocol
ILMI—Interim Local Management Interface