/********************************************************************
*
* Standard register and bit definitions for the Texas Instruments
* MSP430 microcontroller.
*
* This file supports assembler and C development for
* MSP430x13x devices.
*
* Texas Instruments, Version 2.4
*
* Rev. 1.2, Additional Timer B bit definitions.
* Renamed XTOFF to XT2OFF.
* Rev. 1.3, Removed leading 0 to aviod interpretation as octal
* values under C
* Rev. 1.4, Corrected LPMx_EXIT to reference new intrinsic _BIC_SR_IRQ
* Changed TAIV and TBIV to be read-only
* Rev. 1.5, Enclose all #define statements with parentheses
* Rev. 1.6, Defined vectors for USART (in addition to UART)
* Rev. 1.7, Added USART special function labels (UxME, UxIE, UxIFG)
* Rev. 2.1, Alignment of defintions in Users Guide and of version numbers
* Rev. 2.2, Fixed type in ADC12 bit definitions (replaced ADC10 with ADC12)
* Rev. 2.3, Removed unused def of TASSEL2 / TBSSEL2
* Rev. 2.4, added definitions for Interrupt Vectors xxIV
*
********************************************************************/
#ifndef __msp430x13x
#define __msp430x13x
#define __MSP430_HEADER_VERSION__ 1062
#ifdef __IAR_SYSTEMS_ICC__
#ifndef _SYSTEM_BUILD
#pragma system_include
#endif
#endif
#if (((__TID__ >> 8) & 0x7F) != 0x2b) /* 0x2b = 43 dec */
#error msp430f135.h file for use with ICC430/A430 only
#endif
#ifdef __IAR_SYSTEMS_ICC__
#include "in430.h"
#pragma language=extended
#define DEFC(name, address) __no_init volatile unsigned char name @ address;
#define DEFW(name, address) __no_init volatile unsigned short name @ address;
#define DEFXC volatile unsigned char
#define DEFXW volatile unsigned short
#endif /* __IAR_SYSTEMS_ICC__ */
#ifdef __IAR_SYSTEMS_ASM__
#define DEFC(name, address) sfrb name = address;
#define DEFW(name, address) sfrw name = address;
#endif /* __IAR_SYSTEMS_ASM__*/
#ifdef __cplusplus
#define READ_ONLY
#else
#define READ_ONLY const
#endif
/************************************************************
* STANDARD BITS 定义位！
************************************************************/
#define BIT0 (0x0001u)
#define BIT1 (0x0002u)
#define BIT2 (0x0004u)
#define BIT3 (0x0008u)
#define BIT4 (0x0010u)
#define BIT5 (0x0020u)
#define BIT6 (0x0040u)
#define BIT7 (0x0080u)
#define BIT8 (0x0100u)
#define BIT9 (0x0200u)
#define BITA (0x0400u)
#define BITB (0x0800u)
#define BITC (0x1000u)
#define BITD (0x2000u)
#define BITE (0x4000u)
#define BITF (0x8000u)
/************************************************************
* STATUS REGISTER BITS
//状态寄存器的位定义
************************************************************/
#define C (0x0001u)
#define Z (0x0002u)
#define N (0x0004u)
#define V (0x0100u)
#define GIE (0x0008u)
#define CPUOFF (0x0010u)
#define OSCOFF (0x0020u)
#define SCG0 (0x0040u)
#define SCG1 (0x0080u)
/* Low Power Modes coded with Bits 4-7 in SR 节能模式定义*/
#ifndef __IAR_SYSTEMS_ICC__ /* Begin #defines for assembler */
#define LPM0 (CPUOFF) //ACLK和SMCLK保持活动，
#define LPM1 (SCG0+CPUOFF) //ACLK和SMCLK保持活动, 若DCO未用作SMCLK或MCLK，则自流发生器禁止
#define LPM2 (SCG1+CPUOFF) //ACLK、DCO活动
#define LPM3 (SCG1+SCG0+CPUOFF) //ACLK活动，
#define LPM4 (SCG1+SCG0+OSCOFF+CPUOFF) //关闭，
/* End #defines for assembler */
#else /* Begin #defines for C */
#define LPM0_bits (CPUOFF)
#define LPM1_bits (SCG0+CPUOFF)
#define LPM2_bits (SCG1+CPUOFF)
#define LPM3_bits (SCG1+SCG0+CPUOFF)
#define LPM4_bits (SCG1+SCG0+OSCOFF+CPUOFF)
#include "in430.h"
#define LPM0 _BIS_SR(LPM0_bits) /* Enter Low Power Mode 0 */
#define LPM0_EXIT _BIC_SR_IRQ(LPM0_bits) /* Exit Low Power Mode 0 */
#define LPM1 _BIS_SR(LPM1_bits) /* Enter Low Power Mode 1 */
#define LPM1_EXIT _BIC_SR_IRQ(LPM1_bits) /* Exit Low Power Mode 1 */
#define LPM2 _BIS_SR(LPM2_bits) /* Enter Low Power Mode 2 */
#define LPM2_EXIT _BIC_SR_IRQ(LPM2_bits) /* Exit Low Power Mode 2 */
#define LPM3 _BIS_SR(LPM3_bits) /* Enter Low Power Mode 3 */
#define LPM3_EXIT _BIC_SR_IRQ(LPM3_bits) /* Exit Low Power Mode 3 */
#define LPM4 _BIS_SR(LPM4_bits) /* Enter Low Power Mode 4 */
#define LPM4_EXIT _BIC_SR_IRQ(LPM4_bits) /* Exit Low Power Mode 4 */
#endif /* End #defines for C */
/************************************************************
* PERIPHERAL FILE MAP
************************************************************/
/************************************************************
* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS
************************************************************/
#define IE1_ (0x0000u) /* Interrupt Enable 1 //中断使能1 */
DEFC( IE1 , IE1_)
#define U0IE IE1 /* UART0 Interrupt Enable Register */
#define WDTIE (0x01) //看门狗中断使能
#define OFIE (0x02) /*外部晶振故障中断使能*/
#define NMIIE (0x10) /*非屏蔽中断使能*/
#define ACCVIE
(0x20) /*可屏蔽中断使能/flash写中断错误*/
#define URXIE0 (0x40) /*串口0接收中断使能*/
#define UTXIE0 (0x80) /*串口0发送中断使能*/
#define IFG1_ (0x0002u) /* Interrupt Flag 1 */
DEFC( IFG1 , IFG1_)
#define U0IFG IFG1 /* UART0 Interrupt Flag Register */
#define WDTIFG (0x01) /*看门狗定时标志*/
#define OFIFG (0x02) /*外部晶振故障中断标志，不能起震则1，起震后变为0*/
#define NMIIFG (0x10) /*非屏蔽中断标志*/
#define URXIFG0 (0x40)
#define UTXIFG0 (0x80)
#define ME1_ (0x0004u) /* Module Enable 1 */
DEFC( ME1 , ME1_)
#define U0ME ME1 /* UART0 Module Enable Register */
#define URXE0 (0x40) /* 串口0接收中断模式使能 */
#define UTXE0 (0x80) /* 同步中断模式使能 */
#define USPIE0 (0x40) /* 串口0发送中断模式使能 */
/************************************************************
* WATCHDOG TIMER //看门狗定时器
************************************************************/
#define __MSP430_HAS_WDT__ /* Definition to show that Module is available */
#define WDTCTL_ (0x0120u) /* Watchdog Timer Control */
DEFW( WDTCTL , WDTCTL_)
/* The bit names have been prefixed with "WDT" */
#define WDTIS0 (0x0001u)
#define WDTIS1 (0x0002u)
/*看门狗时间间隔选择0 0 32768,0 1 8192,1 0 512,1 1 64*/
#define WDTSSEL (0x0004u) //看门狗时钟源选择0 选择SMCLK 1 选择ACLK
#define WDTCNTCL (0x0008u) //清除看门狗定时器控制位0 不清除内容1 清楚寄存器内容
#define WDTTMSEL (0x0010u) //看门狗工作模式选择0 看门狗模式1 定时器模式
#define WDTNMI (0x0020u) ////RST NMI 管脚功能选择0 复位功能1 NMI 功能
#define WDTNMIES (0x0040u) //看门狗定时器中断触发沿选择位0 上升沿1 下降沿
#define WDTHOLD (0x0080u) //看门狗停止位0 看门狗工作1 看门狗停止工作
#define WDTPW (0x5A00u)
/* WDT-interval times [1ms] coded with Bits 0-2 *///看门狗定时器间隔快捷定义!
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MDLY_32 (WDTPW+WDTTMSEL+WDTCNTCL) /* 32ms interval (default) */
#define WDT_MDLY_8 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0) /* 8ms " */
#define WDT_MDLY_0_5 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1) /* 0.5ms " */
#define WDT_MDLY_0_064 (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 3
2KHz) */
#define WDT_ADLY_1000 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL) /* 1000ms " */
#define WDT_ADLY_250 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */
#define WDT_ADLY_16 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */
#define WDT_ADLY_1_9 (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " */
/* Watchdog mode -> reset after expired time */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MRST_32 (WDTPW+WDTCNTCL) /* 32ms interval (default) */
#define WDT_MRST_8 (WDTPW+WDTCNTCL+WDTIS0) /* 8ms " 32/8*/
#define WDT_MRST_0_5 (WDTPW+WDTCNTCL+WDTIS1) /* 0.5ms " 8/16*/
#define WDT_MRST_0_064 (WDTPW+WDTCNTCL+WDTIS1+WDTIS0) /* 0.064ms " 0.5/8*/
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ARST_1000 (WDTPW+WDTCNTCL+WDTSSEL) /* 1000ms " */
#define WDT_ARST_250 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0) /* 250ms " */
#define WDT_ARST_16 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1) /* 16ms " */
#define WDT_ARST_1_9 (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0) /* 1.9ms " */
/* INTERRUPT CONTROL */
/* These two bits are defined in the Special Function Registers */
/* #define WDTIE 0x01 */
/* #define WDTIFG 0x01 */
/************************************************************
* DIGITAL I/O Port1/2 P1、P2口
************************************************************/
#define __MSP430_HAS_PORT1__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT2__ /* Definition to show that Module is available */
#define P1IN_ (0x0020u) /* Port 1 Input */
READ_ONLY DEFC( P1IN , P1IN_)
#define P1OUT_ (0x0021u) /* Port 1 Output */
DEFC( P1OUT , P1OUT_)
#define P1DIR_ (0x0022u) /* Port 1 Direction */
DEFC( P1DIR , P1DIR_)
#define P1IFG_ (0x0023u) /* Port 1 Interrupt Flag */
DEFC( P1IFG , P1IFG_)
#define P1IES_ (0x0024u) /* Port 1 Interrupt Edge Select 中断触发沿选择寄存器0：上升沿，1：下降沿*/
DEFC( P1IES , P1IES_)
#define P1IE_ (0x0025u) /* Port 1 Interrupt Enable 中断允许寄存器*/
DEFC( P1IE , P1IE_)
#define P1SEL_ (0x0026u) /* Port 1 Selection 功能选择寄存器，0：I\O,1:外围模块功能*/
DEFC( P1SEL , P1SEL_)
#define P2IN_ (0x0028u) /* Port 2 Input */
READ_ONLY DEFC( P2IN , P2IN_)
#define P2OUT_ (0x0029u) /* Port 2 Output */
DEFC( P2OUT , P2OUT_)
#define P2DIR
_ (0x002Au) /* Port 2 Direction */
DEFC( P2DIR , P2DIR_)
#define P2IFG_ (0x002Bu) /* Port 2 Interrupt Flag */
DEFC( P2IFG , P2IFG_)
#define P2IES_ (0x002Cu) /* Port 2 Interrupt Edge Select中断触发沿选择寄存器0：上升沿，1：下降沿 */
DEFC( P2IES , P2IES_)
#define P2IE_ (0x002Du) /* Port 2 Interrupt Enable */
DEFC( P2IE , P2IE_)
#define P2SEL_ (0x002Eu) /* Port 2 Selection */
DEFC( P2SEL , P2SEL_)
/************************************************************
* DIGITAL I/O Port3/4 //P3、4、5、6没有中断能力
************************************************************/
#define __MSP430_HAS_PORT3__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT4__ /* Definition to show that Module is available */
#define P3IN_ (0x0018u) /* Port 3 Input */
READ_ONLY DEFC( P3IN , P3IN_)
#define P3OUT_ (0x0019u) /* Port 3 Output */
DEFC( P3OUT , P3OUT_)
#define P3DIR_ (0x001Au) /* Port 3 Direction */
DEFC( P3DIR , P3DIR_)
#define P3SEL_ (0x001Bu) /* Port 3 Selection */
DEFC( P3SEL , P3SEL_)
#define P4IN_ (0x001Cu) /* Port 4 Input */
READ_ONLY DEFC( P4IN , P4IN_)
#define P4OUT_ (0x001Du) /* Port 4 Output */
DEFC( P4OUT , P4OUT_)
#define P4DIR_ (0x001Eu) /* Port 4 Direction */
DEFC( P4DIR , P4DIR_)
#define P4SEL_ (0x001Fu) /* Port 4 Selection */
DEFC( P4SEL , P4SEL_)
/************************************************************
* DIGITAL I/O Port5/6
************************************************************/
#define __MSP430_HAS_PORT5__ /* Definition to show that Module is available */
#define __MSP430_HAS_PORT6__ /* Definition to show that Module is available */
#define P5IN_ (0x0030u) /* Port 5 Input */
READ_ONLY DEFC( P5IN , P5IN_)
#define P5OUT_ (0x0031u) /* Port 5 Output */
DEFC( P5OUT , P5OUT_)
#define P5DIR_ (0x0032u) /* Port 5 Direction */
DEFC( P5DIR , P5DIR_)
#define P5SEL_ (0x0033u) /* Port 5 Selection */
DEFC( P5SEL , P5SEL_)
#define P6IN_ (0x0034u) /* Port 6 Input */
READ_ONLY DEFC( P6IN , P6IN_)
#define P6OUT_ (0x0035u) /* Port 6 Output */
DEFC( P6OUT , P6OUT_)
#define P6DIR_ (0x0036u) /* Port 6 Direction */
DEFC( P6DIR , P6DIR_)
#define P6SEL_ (0x0037u) /* Port 6 Selection */
DEFC( P6SEL , P6SEL_)
/************************************************************
* USART
*******
*****************************************************/
/* UxCTL 串口控制寄存器*/
#define PENA (0x80) /* Parity enable校验允许位0禁止，1允许 */
#define PEV (0x40) /* Parity 0:odd / 1:even 奇偶校验 0奇1偶*/
#define SPB (0x20) /* Stop Bits 0:one / 1: two ***********停止位0一位，1两位 */
#define CHAR (0x10) /* Data 0:7-bits / 1:8-bits 数据位*/
#define LISTEN (0x08) /* Listen mode 反馈发数据同时在把发的数据接收回来，0无，1有，*/
#define SYNC (0x04) /* UART / SPI mode 同步模式 0异步，1同步*/
#define MM (0x02) /* Master Mode off/on为1时地址位多机协议(异步) 主机模式(同步); 为0时线路空闲多机协议(异步) 从机模式(同步)*/ */
#define SWRST (0x01) /* USART Software Reset控制位 默认为1，正确的USART初始化顺序：先在SWRST=1下设置串口；然后设置SWRST=0；最后如需要中断，则设置相应中断使能*/
/* UxTCTL 串口发送控制寄存器*/
#define CKPH (0x80) /* SPI: Clock Phase 时钟相位控制位(只同步方式用)为1时时钟UCLK延时半个周期（相反）*/
#define CKPL (0x40) /* Clock Polarity 时钟极性控制位 为1时异步与UCLK相反;同步下降延有效*/
#define SSEL1 (0x20) /* Clock Source Select 1时钟源选择位:与SSEL0组合为0,1,2,3四种方式*/ */
#define SSEL0 (0x10) /* Clock Source Select 0 *//*"0"选择外部时钟*UCLKI,"1"选择ACLK,"2","3"选择SMCLK */
#define URXSE (0x08) /* Receive Start edge select 接收触发延控制位(只在异步方式下用)，0无触发沿检测，1有触发沿检测*/
#define TXWAKE (0x04) /* TX Wake up mode 多处理器通信传送控制位(只在异步方式下用)0下一个要传输的字符为数据，1下一个要传输的字符为地址*/
#define STC (0x02) /* SPI: STC enable 0:on / 1:off 外部引脚STE选择位为0时为4线模式 为1时为3线模式*/
#define TXEPT (0x01) /* TX Buffer empty发送器空标志0忙，1空 */
/* UxRCTL 串口接收控制寄存器 同步模式下只用两位:FE和OE*/
#define FE (0x80) /* Frame Error 帧错标志，0无错，1错 */
#define PE (0x40) /* Parity Error 校验错标志位0无错，1错*/
#define OE (0x20) /* Overrun Error 溢出标志位 0无溢出，1溢出*/
#define BRK (0x10) /* Break detected 打断检测位 0无打断，1打断*/
#define URXEIE (0x08) /* RX Error interrupt enable 接收出错中断允许位 0禁止中断 1允许 */
#d
efine URXWIE (0x04) /* RX Wake up interrupt enable 接收唤醒中断允许位 0 所有接收的字符能够置位 URXIFG; 1 只有接收到地址字符才能置位 URXIFG。*/
#define RXWAKE (0x02) /* RX Wake up detect 接收唤醒检测位 0未唤醒，1醒 */
#define RXERR (0x01) /* RX Error Error 接收错误标志位 0无错误，1有错*/
/************************************************************
* USART 0
************************************************************/
#define __MSP430_HAS_UART0__ /* Definition to show that Module is available */
#define U0CTL_ (0x0070u) /* USART 0 Control */
DEFC( U0CTL , U0CTL_) /*串口控制寄存器*/
#define U0TCTL_ (0x0071u) /* USART 0 Transmit Control */
DEFC( U0TCTL , U0TCTL_)/*串口发送控制寄存器*/
#define U0RCTL_ (0x0072u) /* USART 0 Receive Control */
DEFC( U0RCTL , U0RCTL_)/*串口接收控制寄存器
#define U0MCTL_ (0x0073u) /* USART 0 Modulation Control */
DEFC( U0MCTL , U0MCTL_)/*波特率调整控制寄存器*/
#define U0BR0_ (0x0074u) /* USART 0 Baud Rate 0 */
DEFC( U0BR0 , U0BR0_)/*波特率控制寄存器*/
#define U0BR1_ (0x0075u) /* USART 0 Baud Rate 1 */
DEFC( U0BR1 , U0BR1_)/*波特率控制寄存器*/
#define U0RXBUF_ (0x0076u) /* USART 0 Receive Buffer */
READ_ONLY DEFC( U0RXBUF , U0RXBUF_)/**接受缓冲器**/
#define U0TXBUF_ (0x0077u) /* USART 0 Transmit Buffer */
DEFC( U0TXBUF , U0TXBUF_)/**发送缓冲器**/
/* Alternate register names */
#define UCTL0 U0CTL /* USART 0 Control */
#define UTCTL0 U0TCTL /* USART 0 Transmit Control */
#define URCTL0 U0RCTL /* USART 0 Receive Control */
#define UMCTL0 U0MCTL /* USART 0 Modulation Control */
#define UBR00 U0BR0 /* USART 0 Baud Rate 0 */
#define UBR10 U0BR1 /* USART 0 Baud Rate 1 */
#define RXBUF0 U0RXBUF /* USART 0 Receive Buffer */
#define TXBUF0 U0TXBUF /* USART 0 Transmit Buffer */
#define UCTL0_ U0CTL_ /* USART 0 Control */
#define UTCTL0_ U0TCTL_ /* USART 0 Transmit Control */
#define URCTL0_ U0RCTL_ /* USART 0 Receive Control */
#define UMCTL0_ U0MCTL_ /* USART 0 Modulation Control */
#define UBR00_ U0BR0_ /* USART 0 Baud Rate 0 */
#define UBR10_ U0BR1_ /* USART 0 Baud Rate 1 */
#define RXBUF0_ U0RXBUF_ /* USART 0 Receive Buffer */
#define TXBUF0_ U0TXBUF_ /* USART 0 Transmit Buffer */
#define UCTL_0 U0CTL
/* USART 0 Control */
#define UTCTL_0 U0TCTL /* USART 0 Transmit Control */
#define URCTL_0 U0RCTL /* USART 0 Receive Control */
#define UMCTL_0 U0MCTL /* USART 0 Modulation Control */
#define UBR0_0 U0BR0 /* USART 0 Baud Rate 0 */
#define UBR1_0 U0BR1 /* USART 0 Baud Rate 1 */
#define RXBUF_0 U0RXBUF /* USART 0 Receive Buffer */
#define TXBUF_0 U0TXBUF /* USART 0 Transmit Buffer */
#define UCTL_0_ U0CTL_ /* USART 0 Control */
#define UTCTL_0_ U0TCTL_ /* USART 0 Transmit Control */
#define URCTL_0_ U0RCTL_ /* USART 0 Receive Control */
#define UMCTL_0_ U0MCTL_ /* USART 0 Modulation Control */
#define UBR0_0_ U0BR0_ /* USART 0 Baud Rate 0 */
#define UBR1_0_ U0BR1_ /* USART 0 Baud Rate 1 */
#define RXBUF_0_ U0RXBUF_ /* USART 0 Receive Buffer */
#define TXBUF_0_ U0TXBUF_ /* USART 0 Transmit Buffer */
/************************************************************
* Timer A3 定时器A！
************************************************************/
#define __MSP430_HAS_TA3__ /* Definition to show that Module is available */
#define TAIV_ (0x012Eu) /* Timer A Interrupt Vector Word */
READ_ONLY DEFW( TAIV , TAIV_)
#define TACTL_ (0x0160u) /* Timer A Control 定时器控制*/
DEFW( TACTL , TACTL_)
#define TACCTL0_ (0x0162u) /* Timer A Capture/Compare Control 0 */
DEFW( TACCTL0 , TACCTL0_)
#define TACCTL1_ (0x0164u) /* Timer A Capture/Compare Control 1 */
DEFW( TACCTL1 , TACCTL1_)
#define TACCTL2_ (0x0166u) /* Timer A Capture/Compare Control 2 */
DEFW( TACCTL2 , TACCTL2_)
#define TAR_ (0x0170u) /* Timer A Counter Register */
DEFW( TAR , TAR_)
#define TACCR0_ (0x0172u) /* Timer A Capture/Compare 0 */
DEFW( TACCR0 , TACCR0_)
#define TACCR1_ (0x0174u) /* Timer A Capture/Compare 1 */
DEFW( TACCR1 , TACCR1_)
#define TACCR2_ (0x0176u) /* Timer A Capture/Compare 2 */
DEFW( TACCR2 , TACCR2_)
/* Alternate register names */
#define CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */
#define CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */
#define CCTL2 TACCTL2 /* Timer A Capture/Compare Control 2 */
#define CCR0 TACCR0 /* Timer A Capture/Compare 0 */
#define CCR1 TACCR1 /* Timer A Capture/Compare 1 */
#define CCR2 TACCR2 /* Timer A Capture/Compare 2 */
#define CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */
#define CCTL1_ TACCTL1_ /* Timer A Capture/Compa
re Control 1 */
#define CCTL2_ TACCTL2_ /* Timer A Capture/Compare Control 2 */
#define CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */
#define CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */
#define CCR2_ TACCR2_ /* Timer A Capture/Compare 2 */
/* Alternate register names - 5xx style */
#define TA0IV TAIV /* Timer A Interrupt Vector Word */
#define TA0CTL TACTL /* Timer A Control */
#define TA0CCTL0 TACCTL0 /* Timer A Capture/Compare Control 0 */
#define TA0CCTL1 TACCTL1 /* Timer A Capture/Compare Control 1 */
#define TA0CCTL2 TACCTL2 /* Timer A Capture/Compare Control 2 */
#define TA0R TAR /* Timer A Counter Register */
#define TA0CCR0 TACCR0 /* Timer A Capture/Compare 0 */
#define TA0CCR1 TACCR1 /* Timer A Capture/Compare 1 */
#define TA0CCR2 TACCR2 /* Timer A Capture/Compare 2 */
#define TA0IV_ TAIV_ /* Timer A Interrupt Vector Word */
#define TA0CTL_ TACTL_ /* Timer A Control */
#define TA0CCTL0_ TACCTL0_ /* Timer A Capture/Compare Control 0 */
#define TA0CCTL1_ TACCTL1_ /* Timer A Capture/Compare Control 1 */
#define TA0CCTL2_ TACCTL2_ /* Timer A Capture/Compare Control 2 */
#define TA0R_ TAR_ /* Timer A Counter Register */
#define TA0CCR0_ TACCR0_ /* Timer A Capture/Compare 0 */
#define TA0CCR1_ TACCR1_ /* Timer A Capture/Compare 1 */
#define TA0CCR2_ TACCR2_ /* Timer A Capture/Compare 2 */
/*****************TACTL********************/
#define TASSEL1 (0x0200u) /* Timer A clock source select 1 时钟源选择*/
#define TASSEL0 (0x0100u) /* Timer A clock source select 0 ：00外部管脚信号做输入，01ACLK，10MCLK，11外部输入时钟*/
#define ID1 (0x0080u) /* Timer A clock input divider 1 时钟分频系数*/
#define ID0 (0x0040u) /* Timer A clock input divider 0：00不分频，01 1/2，10 1/4，11 1/8*/
#define MC1 (0x0020u) /* Timer A mode control 1 定时器工作模式*/
#define MC0 (0x0010u) /* Timer A mode control 0：0 0 停止模式，0 1 增计数器模式，1 0 连续记数模式，1 1 增/减记数模式*/
#define TACLR (0x0004u) /* Timer A counter clear 定时器清除*/
#define TAIE (0x0002u) /* Timer A counter interrupt enable定时器中断使能0 不允许中断1 允许中断 */
#define TAIFG (0x0001u) /* Timer A counter interrupt flag 中断标志位*/
#define MC_0 (0*0x10u) /* Timer A mode control: 0 - Stop */
#define MC_1 (1*0x10u) /* Timer A mode control: 1 - Up to CCR0 */
#define MC_2 (2*0x10u) /* Timer A mode control: 2 - Continous up */
#define MC_3 (3*
0x10u) /* Timer A mode control: 3 - Up/Down */
#define ID_0 (0*0x40u) /* Timer A input divider: 0 - /1 */
#define ID_1 (1*0x40u) /* Timer A input divider: 1 - /2 */
#define ID_2 (2*0x40u) /* Timer A input divider: 2 - /4 */
#define ID_3 (3*0x40u) /* Timer A input divider: 3 - /8 */
#define TASSEL_0 (0*0x100u) /* Timer A clock source select: 0 - TACLK */
#define TASSEL_1 (1*0x100u) /* Timer A clock source select: 1 - ACLK */
#define TASSEL_2 (2*0x100u) /* Timer A clock source select: 2 - SMCLK */
#define TASSEL_3 (3*0x100u) /* Timer A clock source select: 3 - INCLK */
/***********************CCTLx***************************88*/
#define CM1 (0x8000u) /* Capture mode 1 捕获方式 0禁止 1上 2下 3都*/
#define CM0 (0x4000u) /* Capture mode 0 */
#define CCIS1 (0x2000u) /* Capture input select 1 捕获信号输入源0A 1B 2GND 3VCC */
#define CCIS0 (0x1000u) /* Capture input select 0 */
#define SCS (0x0800u) /* Capture sychronize sychronize 同步\异步捕获0异步1同步 */
#define SCCI (0x0400u) /* Latched capture signal (read) 锁定的捕获信号*/
#define CAP (0x0100u) /* Capture mode: 1 /Compare mode : 0 */ //比较模式0，捕获模式1；
#define OUTMOD2 (0x0080u) /* Output mode 2 输出模式选择*/
#define OUTMOD1 (0x0040u) /* Output mode 1 */
#define OUTMOD0 (0x0020u) /* Output mode 0 */
#define CCIE (0x0010u) /* Capture/compare interrupt enable */
#define CCI (0x0008u) /* Capture input signal (read) 捕获信号*/
#define OUT (0x0004u) /* PWM Output signal if output mode 0 输出位*/
#define COV (0x0002u) /* Capture/compare overflow flag */ //捕获溢出标志
#define CCIFG (0x0001u) /* Capture/compare interrupt flag 中断标志位*/
#define OUTMOD_0 (0*0x20u) /* PWM output mode: 0 - output only 立即，直接输出OUT位*/
#define OUTMOD_1 (1*0x20u) /* PWM output mode: 1 - set CCRx置位；CCR0保持(all)*/
#define OUTMOD_2 (2*0x20u) /* PWM output mode: 2 - PWM toggle/reset CCRx翻转；CCR0复位(all)*/
#define OUTMOD_3 (3*0x20u) /* PWM output mode: 3 - PWM set/reset CCRx置位；CCR0复位*/
#define OUTMOD_4 (4*0x20u) /* PWM output mode: 4 - toggle CCRx翻转；CCR0保持(all)*/
#define OUTMOD_5 (5*0x20u) /* PWM output mode: 5 - Reset CCRx复位；CCR0保持(all) */
#define OUTMOD_6 (6*0x20u) /* PWM output mode: 6 - PWM toggle/set CCRx翻转；CCR0置位*/
#define OUTMOD_7 (7*0x20u) /* PWM output mode: 7 -
PWM reset/set CCRx复位；CCR0置位*/
#define CCIS_0 (0*0x1000u) /* Capture input select: 0 - CCIxA CCIxA作为捕获输入源*/
#define CCIS_1 (1*0x1000u) /* Capture input select: 1 - CCIxB CCIxB作为捕获输入源*/
#define CCIS_2 (2*0x1000u) /* Capture input select: 2 - GND 软件产生一个下降沿*/
#define CCIS_3 (3*0x1000u) /* Capture input select: 3 - Vcc 软件产生一个下降沿*/
#define CM_0 (0*0x4000u) /* Capture mode: 0 - disabled 禁止捕获*/
#define CM_1 (1*0x4000u) /* Capture mode: 1 - pos. edge 上升沿捕获 */
#define CM_2 (2*0x4000u) /* Capture mode: 1 - neg. edge 下降沿捕获 */
#define CM_3 (3*0x4000u) /* Capture mode: 1 - both edges 降沿都捕获 */
/* TA3IV Definitions */
#define TAIV_TACCR1 (0x0002u) /* TACCR1_CCIFG */
#define TAIV_TACCR2 (0x0004u) /* TACCR2_CCIFG */
#define TAIV_TAIFG (0x000Au) /* TAIFG */
#define TAIV_NONE (0x0000u) /* No Interrupt pending */
#define TAIV_6 (0x0006u) /* Reserved */
#define TAIV_8 (0x0008u) /* Reserved */
/************************************************************
* Timer B3
************************************************************/
#define __MSP430_HAS_TB3__ /* Definition to show that Module is available */
#define TBIV_ (0x011Eu) /* Timer B Interrupt Vector Word */
READ_ONLY DEFW( TBIV , TBIV_)
#define TBCTL_ (0x0180u) /* Timer B Control */
DEFW( TBCTL , TBCTL_)
#define TBCCTL0_ (0x0182u) /* Timer B Capture/Compare Control 0 */
DEFW( TBCCTL0 , TBCCTL0_)
#define TBCCTL1_ (0x0184u) /* Timer B Capture/Compare Control 1 */
DEFW( TBCCTL1 , TBCCTL1_)
#define TBCCTL2_ (0x0186u) /* Timer B Capture/Compare Control 2 */
DEFW( TBCCTL2 , TBCCTL2_)
#define TBR_ (0x0190u) /* Timer B Counter Register */
DEFW( TBR , TBR_)
#define TBCCR0_ (0x0192u) /* Timer B Capture/Compare 0 */
DEFW( TBCCR0 , TBCCR0_)
#define TBCCR1_ (0x0194u) /* Timer B Capture/Compare 1 */
DEFW( TBCCR1 , TBCCR1_)
#define TBCCR2_ (0x0196u) /* Timer B Capture/Compare 2 */
DEFW( TBCCR2 , TBCCR2_)
/* Alternate register names - 5xx style */
#define TB0IV TBIV /* Timer B Interrupt Vector Word */
#define TB0CTL TBCTL /* Timer B Control */
#define TB0CCTL0 TBCCTL0 /* Timer B Capture/Compare Control 0 */
#define TB0CCTL1 TBCCTL1 /* Timer B Capture/Compare Control 1 */
#define TB0CCTL2 TBCCTL2 /* Timer B Capture/Compare Control 2 */
#define TB0R
TBR /* Timer B Counter Register */
#define TB0CCR0 TBCCR0 /* Timer B Capture/Compare 0 */
#define TB0CCR1 TBCCR1 /* Timer B Capture/Compare 1 */
#define TB0CCR2 TBCCR2 /* Timer B Capture/Compare 2 */
#define TB0IV_ TBIV_ /* Timer B Interrupt Vector Word */
#define TB0CTL_ TBCTL_ /* Timer B Control */
#define TB0CCTL0_ TBCCTL0_ /* Timer B Capture/Compare Control 0 */
#define TB0CCTL1_ TBCCTL1_ /* Timer B Capture/Compare Control 1 */
#define TB0CCTL2_ TBCCTL2_ /* Timer B Capture/Compare Control 2 */
#define TB0R_ TBR_ /* Timer B Counter Register */
#define TB0CCR0_ TBCCR0_ /* Timer B Capture/Compare 0 */
#define TB0CCR1_ TBCCR1_ /* Timer B Capture/Compare 1 */
#define TB0CCR2_ TBCCR2_ /* Timer B Capture/Compare 2 */
#define TBCLGRP1 (0x4000u) /* Timer B Compare latch load group 1 */
#define TBCLGRP0 (0x2000u) /* Timer B Compare latch load group 0 */
#define CNTL1 (0x1000u) /* Counter lenght 1 */
#define CNTL0 (0x0800u) /* Counter lenght 0 */
#define TBSSEL1 (0x0200u) /* Clock source 1 */
#define TBSSEL0 (0x0100u) /* Clock source 0 */
#define TBCLR (0x0004u) /* Timer B counter clear */
#define TBIE (0x0002u) /* Timer B interrupt enable */
#define TBIFG (0x0001u) /* Timer B interrupt flag */
#define SHR1 (0x4000u) /* Timer B Compare latch load group 1 */
#define SHR0 (0x2000u) /* Timer B Compare latch load group 0 */
#define TBSSEL_0 (0*0x0100u) /* Clock Source: TBCLK */
#define TBSSEL_1 (1*0x0100u) /* Clock Source: ACLK */
#define TBSSEL_2 (2*0x0100u) /* Clock Source: SMCLK */
#define TBSSEL_3 (3*0x0100u) /* Clock Source: INCLK */
#define CNTL_0 (0*0x0800u) /* Counter lenght: 16 bit */
#define CNTL_1 (1*0x0800u) /* Counter lenght: 12 bit */
#define CNTL_2 (2*0x0800u) /* Counter lenght: 10 bit */
#define CNTL_3 (3*0x0800u) /* Counter lenght: 8 bit */
#define SHR_0 (0*0x2000u) /* Timer B Group: 0 - individually */
#define SHR_1 (1*0x2000u) /* Timer B Group: 1 - 3 groups (1-2, 3-4, 5-6) */
#define SHR_2 (2*0x2000u) /* Timer B Group: 2 - 2 groups (1-3, 4-6)*/
#define SHR_3 (3*0x2000u) /* Timer B Group: 3 - 1 group (all) */
#define TBCLGRP_0 (0*0x2000u) /* Timer B Group: 0 - individually */
#define TBCLGRP_1 (1*0x2000u) /* Timer B Group: 1 - 3 groups (1-2, 3-4, 5-6) */
#define TBCLGRP_2 (2*0x2000u) /* Timer B Group: 2 - 2 groups (1-3, 4-6)*/
#define TBCLGRP_3 (3*0x2000u) /* Timer B Group: 3 - 1 group (all) */
/* Additional Timer B Control Register bits are defined in Ti
mer A */
#define CLLD1 (0x0400u) /* Compare latch load source 1 */
#define CLLD0 (0x0200u) /* Compare latch load source 0 */
#define SLSHR1 (0x0400u) /* Compare latch load source 1 */
#define SLSHR0 (0x0200u) /* Compare latch load source 0 */
#define SLSHR_0 (0*0x0200u) /* Compare latch load sourec : 0 - immediate */
#define SLSHR_1 (1*0x0200u) /* Compare latch load sourec : 1 - TBR counts to 0 */
#define SLSHR_2 (2*0x0200u) /* Compare latch load sourec : 2 - up/down */
#define SLSHR_3 (3*0x0200u) /* Compare latch load sourec : 3 - TBR counts to TBCTL0 */
#define CLLD_0 (0*0x0200u) /* Compare latch load sourec : 0 - immediate */
#define CLLD_1 (1*0x0200u) /* Compare latch load sourec : 1 - TBR counts to 0 */
#define CLLD_2 (2*0x0200u) /* Compare latch load sourec : 2 - up/down */
#define CLLD_3 (3*0x0200u) /* Compare latch load sourec : 3 - TBR counts to TBCTL0 */
/* TB3IV Definitions */
#define TBIV_NONE (0x0000u) /* No Interrupt pending */
#define TBIV_TBCCR1 (0x0002u) /* TBCCR1_CCIFG */
#define TBIV_TBCCR2 (0x0004u) /* TBCCR2_CCIFG */
#define TBIV_3 (0x0006u) /* Reserved */
#define TBIV_4 (0x0008u) /* Reserved */
#define TBIV_5 (0x000Au) /* Reserved */
#define TBIV_6 (0x000Cu) /* Reserved */
#define TBIV_TBIFG (0x000Eu) /* TBIFG */
/************************************************************
* Basic Clock Module //时钟寄存器
************************************************************/
#define __MSP430_HAS_BASIC_CLOCK__ /* Definition to show that Module is available */
#define DCOCTL_ (0x0056u) /* DCO Clock Frequency Control */
DEFC( DCOCTL , DCOCTL_)
#define BCSCTL1_ (0x0057u) /* Basic Clock System Control 1 */
DEFC( BCSCTL1 , BCSCTL1_)
#define BCSCTL2_ (0x0058u) /* Basic Clock System Control 2 */
DEFC( BCSCTL2 , BCSCTL2_)
/*DCO.0——DCO.2定义8种频率之一，可分段调节DCOCLK频率，相邻两种频率相差10%。而频率由注入直流发生器的电流定义。
MOD.O——MOD.4定义在32个DCO周期中插入的fdco+l周期个数，而在余下的DCO周期中为fDco周期，控制切换DCO和DCO+1选择的两种频率。如果DCO常数为7，表示已经选择最高颂率，此时不能利用MOD.O-MOD.4进行频率调整。*/
#define MOD0 (0x01) /* Modulation Bit 0 */
#define MOD1 (0x02) /* Modulation Bit 1 */
#define MOD2 (0x04) /* Modulation Bit 2 */
#define MOD3 (0x08) /* Modulation Bit 3 */
#define MOD4 (0x10) /* Modulation Bit 4 */
#define DCO0 (0x20) /* DCO Select Bit 0 */
#define DCO1 (0x40) /* DCO Select Bit 1 */
#define DCO2 (0x80) /* DCO Select Bit 2 */
#define RSEL0 (0x01) /* Range Select Bit 0 */
#define RSEL1 (0x02) /* Range Select Bit 1 */
#define RSEL2 (0x04) /* Range Select Bit 2 */
#define XT5V (0x08) /* XT5V should always be reset此位设置为0 */
#define DIVA0 (0x10) /* ACLK Divider 0 控制ACLK分频*/
#define DIVA1 (0x20) /* ACLK Divider 1 00：不分频；012分频；104分频；118分频*/
#define XTS (0x40) /* LFXTCLK 0:Low Freq默认 / 1: High Freq.控制 LFXTl 工作模武 */
#define XT2OFF (0x80) /* Enable XT2CLK ：XT2OFF=O，XT2振荡器开启；默认为关闭*/
#define DIVA_0 (0x00) /* ACLK Divider 0: /1 */
#define DIVA_1 (0x10) /* ACLK Divider 1: /2 */
#define DIVA_2 (0x20) /* ACLK Divider 2: /4 */
#define DIVA_3 (0x30) /* ACLK Divider 3: /8 */
#define DCOR (0x01) /* Enable External Resistor : 1 选择 DCO 电阻（0：内部；1：外部）*/
#define DIVS0 (0x02) /* SMCLK Divider 0 选择 SMCLK 分频*/
#define DIVS1 (0x04) /* SMCLK Divider 1 */
#define SELS (0x08) /* SMCLK Source Select SMCLK时钟源0:DCOCLK / 1:XT2CLK*/
#define DIVM0 (0x10) /* MCLK Divider 0 选择 MCLK 分频*/
#define DIVM1 (0x20) /* MCLK Divider 1 */
#define SELM0 (0x40) /* MCLK Source Select 0选择 MCLK 时钟源 */
#define SELM1 (0x80) /* MCLK Source Select 1：0、1DCOCLK ，2T2，3T1 */
#define DIVS_0 (0x00) /* SMCLK Divider 0: /1 */
#define DIVS_1 (0x02) /* SMCLK Divider 1: /2 */
#define DIVS_2 (0x04) /* SMCLK Divider 2: /4 */
#define DIVS_3 (0x06) /* SMCLK Divider 3: /8 */
#define DIVM_0 (0x00) /* MCLK Divider 0: /1 */
#define DIVM_1 (0x10) /* MCLK Divider 1: /2 */
#define DIVM_2 (0x20) /* MCLK Divider 2: /4 */
#define DIVM_3 (0x30) /* MCLK Divider 3: /8 */
#define SELM_0 (0x00) /* MCLK Source Select 0: DCOCLK */
#define SELM_1 (0x40) /* MCLK Source Select 1: DCOCLK */
#define SELM_2 (0x80) /* MCLK Source Select 2: XT2CLK/LFXTCLK */
#define SELM_3 (0xC0) /* MCLK Source Select 3: LFXTCLK */
/*************************************************************
* Flash Memory FLASH存储
*************************************************************/
#define __MSP430_HAS_FLASH__ /* Definition to show that Module is available */
//控制寄存器定义
#define
FCTL1_ (0x0128u) /* FLASH Control 1 */
DEFW( FCTL1 , FCTL1_)
#define FCTL2_ (0x012Au) /* FLASH Control 2 */
DEFW( FCTL2 , FCTL2_)
#define FCTL3_ (0x012Cu) /* FLASH Control 3 */
DEFW( FCTL3 , FCTL3_)
//安全键值定义
#define FRKEY (0x9600u) /* Flash key returned by read */
#define FWKEY (0xA500u) /* Flash key for write */
#define FXKEY (0x3300u) /* for use with XOR instruction */
//位定义
#define ERASE (0x0002u) /* Enable bit for Flash segment erase */
#define MERAS (0x0004u) /* Enable bit for Flash mass erase */
#define WRT (0x0040u) /* Enable bit for Flash write */
#define BLKWRT (0x0080u) /* Enable bit for Flash segment write */
#define SEGWRT (0x0080u) /* old definition */ /* Enable bit for Flash segment write */
//分频因子
#define FN0 (0x0001u) /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */
#define FN1 (0x0002u) /* 32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */
#ifndef FN2
#define FN2 (0x0004u)
#endif
#ifndef FN3
#define FN3 (0x0008u)
#endif
#ifndef FN4
#define FN4 (0x0010u)
#endif
#define FN5 (0x0020u)
#define FSSEL0 (0x0040u) /* Flash clock select 0 */ /* to distinguish from USART SSELx */
//时钟源选择
#define FSSEL1 (0x0080u) /* Flash clock select 1 */
#define FSSEL_0 (0x0000u) /* Flash clock select: 0 - ACLK */
#define FSSEL_1 (0x0040u) /* Flash clock select: 1 - MCLK */
#define FSSEL_2 (0x0080u) /* Flash clock select: 2 - SMCLK */
#define FSSEL_3 (0x00C0u) /* Flash clock select: 3 - SMCLK */
//位定义
#define BUSY (0x0001u) /* Flash busy: 1 */
#define KEYV (0x0002u) /* Flash Key violation flag */
#define ACCVIFG (0x0004u) /* Flash Access violation flag */
#define WAIT (0x0008u) /* Wait flag for segment write */
#define LOCK (0x0010u) /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX (0x0020u) /* Flash Emergency Exit */
/************************************************************
********************* Comparator A比较器
************************************************************/
#define __MSP430_HAS_COMPA__ /* Definition to show that Module is available */
#define CACTL1_ (0x0059u) /* Comparator A Control 1 */
DEFC( CACTL1 , CACTL1_)
#define CACTL2_ (0x005Au) /* Comparator A Control 2 */
DEFC( CACTL2 , CACTL2_)
#define CAPD_ (0x005Bu) /* Comparator A Port Disable */
DEFC( CAPD , CAPD_)
#define CAIFG (0x01) /* Comp.
A Interrupt Flag */
#define CAIE (0x02) /* Comp. A Interrupt Enable */
#define CAIES (0x04) /* Comp. A Int. Edge Select: 0:rising / 1:falling */
#define CAON (0x08) /* Comp. A enable 比较器使能*/
#define CAREF0 (0x10) /* Comp. A Internal Reference Select 0 */
#define CAREF1 (0x20) /* Comp. A Internal Reference Select 1 */
#define CARSEL (0x40) /* Comp. A Internal Reference Enable *******选择内部参考源加到比较器 A 正端或负端（与CAEX配合） */
#define CAEX (0x80) /* Comp. A Exchange Inputs *******参考电路原理图设计******/
#define CAREF_0 (0x00) /* Comp. A Int. Ref. Select 0 : Off */
#define CAREF_1 (0x10) /* Comp. A Int. Ref. Select 1 : 0.25*Vcc */
#define CAREF_2 (0x20) /* Comp. A Int. Ref. Select 2 : 0.5*Vcc */
#define CAREF_3 (0x30) /* Comp. A Int. Ref. Select 3 : Vt*/
#define CAOUT (0x01) /* Comp. A Output */
#define CAF (0x02) /* Comp. A Enable Output Filter */
#define P2CA0 (0x04) /* Comp. A Connect External Signal to CA0 : 1 */
#define P2CA1 (0x08) /* Comp. A Connect External Signal to CA1 : 1 */
#define CACTL24 (0x10)
#define CACTL25 (0x20)
#define CACTL26 (0x40)
#define CACTL27 (0x80)
#define CAPD0 (0x01) /* Comp. A Disable Input Buffer of Port Register .0 */
#define CAPD1 (0x02) /* Comp. A Disable Input Buffer of Port Register .1 */
#define CAPD2 (0x04) /* Comp. A Disable Input Buffer of Port Register .2 */
#define CAPD3 (0x08) /* Comp. A Disable Input Buffer of Port Register .3 */
#define CAPD4 (0x10) /* Comp. A Disable Input Buffer of Port Register .4 */
#define CAPD5 (0x20) /* Comp. A Disable Input Buffer of Port Register .5 */
#define CAPD6 (0x40) /* Comp. A Disable Input Buffer of Port Register .6 */
#define CAPD7 (0x80) /* Comp. A Disable Input Buffer of Port Register .7 */
/************************************************************
* ADC12模数转换（8通道、12位）
************************************************************/
#define __MSP430_HAS_ADC12__ /* Definition to show that Module is available */
#define ADC12CTL0_ (0x01A0u) /* ADC12 Control 0 */
DEFW( ADC12CTL0 , ADC12CTL0_)
#define ADC12CTL1_ (0x01A2u) /* ADC12 Control 1 */
DEFW( ADC12CTL1 , ADC12CTL1_)
#define ADC12IFG_ (0x01A4u) /* ADC12 Interrupt Flag */
DEFW( ADC12IFG , ADC12IFG_)
#define ADC12IE_ (0x01A6u) /* ADC12 Interrupt Enable */
DEFW( ADC12IE , ADC12IE_)
#define ADC12IV
_ (0x01A8u) /* ADC12 Interrupt Vector Word */
DEFW( ADC12IV , ADC12IV_)
#define ADC12MEM_ (0x0140u) /* ADC12 Conversion Memory */
#ifndef __IAR_SYSTEMS_ICC__
#define ADC12MEM (ADC12MEM_) /* ADC12 Conversion Memory (for assembler) */
#else
#define ADC12MEM ((int*) ADC12MEM_) /* ADC12 Conversion Memory (for C) */
#endif
#define ADC12MEM0_ (0x0140u) /* ADC12 Conversion Memory 0 */ //低十二位有效。高四位为0
DEFW( ADC12MEM0 , ADC12MEM0_)
#define ADC12MEM1_ (0x0142u) /* ADC12 Conversion Memory 1 */
DEFW( ADC12MEM1 , ADC12MEM1_)
#define ADC12MEM2_ (0x0144u) /* ADC12 Conversion Memory 2 */
DEFW( ADC12MEM2 , ADC12MEM2_)
#define ADC12MEM3_ (0x0146u) /* ADC12 Conversion Memory 3 */
DEFW( ADC12MEM3 , ADC12MEM3_)
#define ADC12MEM4_ (0x0148u) /* ADC12 Conversion Memory 4 */
DEFW( ADC12MEM4 , ADC12MEM4_)
#define ADC12MEM5_ (0x014Au) /* ADC12 Conversion Memory 5 */
DEFW( ADC12MEM5 , ADC12MEM5_)
#define ADC12MEM6_ (0x014Cu) /* ADC12 Conversion Memory 6 */
DEFW( ADC12MEM6 , ADC12MEM6_)
#define ADC12MEM7_ (0x014Eu) /* ADC12 Conversion Memory 7 */
DEFW( ADC12MEM7 , ADC12MEM7_)
#define ADC12MEM8_ (0x0150u) /* ADC12 Conversion Memory 8 */
DEFW( ADC12MEM8 , ADC12MEM8_)
#define ADC12MEM9_ (0x0152u) /* ADC12 Conversion Memory 9 */
DEFW( ADC12MEM9 , ADC12MEM9_)
#define ADC12MEM10_ (0x0154u) /* ADC12 Conversion Memory 10 */
DEFW( ADC12MEM10 , ADC12MEM10_)
#define ADC12MEM11_ (0x0156u) /* ADC12 Conversion Memory 11 */
DEFW( ADC12MEM11 , ADC12MEM11_)
#define ADC12MEM12_ (0x0158u) /* ADC12 Conversion Memory 12 */
DEFW( ADC12MEM12 , ADC12MEM12_)
#define ADC12MEM13_ (0x015Au) /* ADC12 Conversion Memory 13 */
DEFW( ADC12MEM13 , ADC12MEM13_)
#define ADC12MEM14_ (0x015Cu) /* ADC12 Conversion Memory 14 */
DEFW( ADC12MEM14 , ADC12MEM14_)
#define ADC12MEM15_ (0x015Eu) /* ADC12 Conversion Memory 15 */
DEFW( ADC12MEM15 , ADC12MEM15_)
#define ADC12MCTL_ (0x0080u) /* ADC12 Memory Control */
#ifndef __IAR_SYSTEMS_ICC__
#define ADC12MCTL (ADC12MCTL_) /* ADC12 Memory Control (for assembler) */
#else
#define ADC12MCTL ((char*) ADC12MCTL_) /* ADC12 Memory Control (for C) */
#endif
#define ADC12MCTL0_ (0x0080u) /* ADC12 Memory Control 0 */
DEFC( ADC12MCTL0 , ADC12MCTL0_)
#define ADC12MCTL1_ (0x0081u) /* ADC12 Memory Control 1 */
DEFC( ADC12MCTL1 , ADC12MCTL1_)
#define ADC12MCTL2_ (0x0082u) /* ADC12 Memory Control 2 */
DEFC( ADC12MCTL2 , ADC12MCTL2_)
#define ADC12MCTL3_ (0x0083u) /* ADC12 Memory Control 3 */
DEFC( ADC12MCTL3 , ADC12MCTL3_)
#define ADC12MCTL4_
(0x0084u) /* ADC12 Memory Control 4 */
DEFC( ADC12MCTL4 , ADC12MCTL4_)
#define ADC12MCTL5_ (0x0085u) /* ADC12 Memory Control 5 */
DEFC( ADC12MCTL5 , ADC12MCTL5_)
#define ADC12MCTL6_ (0x0086u) /* ADC12 Memory Control 6 */
DEFC( ADC12MCTL6 , ADC12MCTL6_)
#define ADC12MCTL7_ (0x0087u) /* ADC12 Memory Control 7 */
DEFC( ADC12MCTL7 , ADC12MCTL7_)
#define ADC12MCTL8_ (0x0088u) /* ADC12 Memory Control 8 */
DEFC( ADC12MCTL8 , ADC12MCTL8_)
#define ADC12MCTL9_ (0x0089u) /* ADC12 Memory Control 9 */
DEFC( ADC12MCTL9 , ADC12MCTL9_)
#define ADC12MCTL10_ (0x008Au) /* ADC12 Memory Control 10 */
DEFC( ADC12MCTL10 , ADC12MCTL10_)
#define ADC12MCTL11_ (0x008Bu) /* ADC12 Memory Control 11 */
DEFC( ADC12MCTL11 , ADC12MCTL11_)
#define ADC12MCTL12_ (0x008Cu) /* ADC12 Memory Control 12 */
DEFC( ADC12MCTL12 , ADC12MCTL12_)
#define ADC12MCTL13_ (0x008Du) /* ADC12 Memory Control 13 */
DEFC( ADC12MCTL13 , ADC12MCTL13_)
#define ADC12MCTL14_ (0x008Eu) /* ADC12 Memory Control 14 */
DEFC( ADC12MCTL14 , ADC12MCTL14_)
#define ADC12MCTL15_ (0x008Fu) /* ADC12 Memory Control 15 */
DEFC( ADC12MCTL15 , ADC12MCTL15_)
/* ADC12CTL0 */
#define ADC12SC (0x001) /* ADC12 Start Conversion */ //采样转换控制位（和 SHP,ISSH,ENC 有关）
#define ENC (0x002) /* ADC12 Enable Conversion */ //转换允许位
#define ADC12TOVIE (0x004) /* ADC12 Timer Overflow interrupt enable */ //转换时间溢出中断允许（多次采样请求）
#define ADC12OVIE (0x008) /* ADC12 Overflow interrupt enable */ //溢出中断允许（ADC12MEMx 多次写入）
#define ADC12ON (0x010) /* ADC12 On/enable */ //ADC12 内核控制
#define REFON (0x020) /* ADC12 Reference on */ //内部基准电压发生器控制
#define REF2_5V (0x040) /* ADC12 Ref 0:1.5V / 1:2.5V */ //内部基准电压选择 1.5V/2.5V
#define MSC (0x080) /* ADC12 Multiple SampleConversion */ //多次采样/转换控制位
#define SHT00 (0x0100u) /* ADC12 Sample Hold 0 Select 0 */ //0~7 通道的采样保持器时间控制
#define SHT01 (0x0200u) /* ADC12 Sample Hold 0 Select 1 */ //8~15 通道的采样保持器时间控制
#define SHT02 (0x0400u) /* ADC12 Sample Hold 0 Select 2 */
#define SHT03 (0x0800u) /* ADC12 Sample Hold 0 Select 3 */
#define SHT10 (0x1000u) /* ADC12 Sample Hold 0 Select 0 */
#define SHT11 (0x2000u) /* ADC12 Sample Hold 1 Select 1 */
#define SHT12 (0x4000u) /* ADC12 Sample Hold 2 Select 2 */
#define SHT13 (0x8000u) /* ADC12 Sample Hold 3 Select 3 */
#define MSH
(0x080)
#define SHT0_0 (0*0x100u) /* ADC12 Sample Hold 0 Select Bit: 0 */
#define SHT0_1 (1*0x100u) /* ADC12 Sample Hold 0 Select Bit: 1 */
#define SHT0_2 (2*0x100u) /* ADC12 Sample Hold 0 Select Bit: 2 */
#define SHT0_3 (3*0x100u) /* ADC12 Sample Hold 0 Select Bit: 3 */
#define SHT0_4 (4*0x100u) /* ADC12 Sample Hold 0 Select Bit: 4 */
#define SHT0_5 (5*0x100u) /* ADC12 Sample Hold 0 Select Bit: 5 */
#define SHT0_6 (6*0x100u) /* ADC12 Sample Hold 0 Select Bit: 6 */
#define SHT0_7 (7*0x100u) /* ADC12 Sample Hold 0 Select Bit: 7 */
#define SHT0_8 (8*0x100u) /* ADC12 Sample Hold 0 Select Bit: 8 */
#define SHT0_9 (9*0x100u) /* ADC12 Sample Hold 0 Select Bit: 9 */
#define SHT0_10 (10*0x100u) /* ADC12 Sample Hold 0 Select Bit: 10 */
#define SHT0_11 (11*0x100u) /* ADC12 Sample Hold 0 Select Bit: 11 */
#define SHT0_12 (12*0x100u) /* ADC12 Sample Hold 0 Select Bit: 12 */
#define SHT0_13 (13*0x100u) /* ADC12 Sample Hold 0 Select Bit: 13 */
#define SHT0_14 (14*0x100u) /* ADC12 Sample Hold 0 Select Bit: 14 */
#define SHT0_15 (15*0x100u) /* ADC12 Sample Hold 0 Select Bit: 15 */
#define SHT1_0 (0*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 0 */
#define SHT1_1 (1*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 1 */
#define SHT1_2 (2*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 2 */
#define SHT1_3 (3*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 3 */
#define SHT1_4 (4*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 4 */
#define SHT1_5 (5*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 5 */
#define SHT1_6 (6*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 6 */
#define SHT1_7 (7*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 7 */
#define SHT1_8 (8*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 8 */
#define SHT1_9 (9*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 9 */
#define SHT1_10 (10*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 10 */
#define SHT1_11 (11*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 11 */
#define SHT1_12 (12*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 12 */
#define SHT1_13 (13*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 13 */
#define SHT1_14 (14*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 14 */
#define SHT1_15 (15*0x1000u) /* ADC12 Sample Hold 1 Select Bit: 15 */
/* ADC12CTL1 */
#define ADC12BUSY (0x0001u) /* ADC12 Busy */ //忙标志（转换中...）
#define CONSEQ0 (0x0002u) /* ADC12 Conversion Sequence Select 0 */ //转换模式
#define CONSEQ1 (0x0004u) /* ADC12 Conversion Sequence Select 1 */ //
#define ADC12SSEL0 (0x0008u) /* ADC12 Clock Source Select 0
*/ //ADC12 时钟选择
#define ADC12SSEL1 (0x0010u) /* ADC12 Clock Source Select 1 */
#define ADC12DIV0 (0x0020u) /* ADC12 Clock Divider Select 0 */ //ADC12 时钟分频控制
#define ADC12DIV1 (0x0040u) /* ADC12 Clock Divider Select 1 */
#define ADC12DIV2 (0x0080u) /* ADC12 Clock Divider Select 2 */
#define ISSH (0x0100u) /* ADC12 Invert Sample Hold Signal */ //采样输入信号同向0/反向1
#define SHP (0x0200u) /* ADC12 Sample/Hold Pulse Mode */ //采样信号 SAMPCON 选择
#define SHS0 (0x0400u) /* ADC12 Sample/Hold Source 0 */ //采样触发源选择
#define SHS1 (0x0800u) /* ADC12 Sample/Hold Source 1 */
#define CSTARTADD0 (0x1000u) /* ADC12 Conversion Start Address 0 */ //定义单次转换的启始地址或者序列通道转换的首地址。
#define CSTARTADD1 (0x2000u) /* ADC12 Conversion Start Address 1 */
#define CSTARTADD2 (0x4000u) /* ADC12 Conversion Start Address 2 */
#define CSTARTADD3 (0x8000u) /* ADC12 Conversion Start Address 3 */
#define CONSEQ_0 (0*2u) /* ADC12 Conversion Sequence Select: 0 */ //单通道 单次
#define CONSEQ_1 (1*2u) /* ADC12 Conversion Sequence Select: 1 */ //多通道 单次
#define CONSEQ_2 (2*2u) /* ADC12 Conversion Sequence Select: 2 */ //单通道 多次
#define CONSEQ_3 (3*2u) /* ADC12 Conversion Sequence Select: 3 */ // 多 多
#define ADC12SSEL_0 (0*8u) /* ADC12 Clock Source Select: 0 */ //ADC12OSC
#define ADC12SSEL_1 (1*8u) /* ADC12 Clock Source Select: 1 */ //ACLK
#define ADC12SSEL_2 (2*8u) /* ADC12 Clock Source Select: 2 */ //MCLK
#define ADC12SSEL_3 (3*8u) /* ADC12 Clock Source Select: 3 */ //SMCLK
#define ADC12DIV_0 (0*0x20u) /* ADC12 Clock Divider Select: 0 */ // clk/1
#define ADC12DIV_1 (1*0x20u) /* ADC12 Clock Divider Select: 1 */ //clk/2
#define ADC12DIV_2 (2*0x20u) /* ADC12 Clock Divider Select: 2 */ //
#define ADC12DIV_3 (3*0x20u) /* ADC12 Clock Divider Select: 3 */ //
#define ADC12DIV_4 (4*0x20u) /* ADC12 Clock Divider Select: 4 */ //
#define ADC12DIV_5 (5*0x20u) /* ADC12 Clock Divider Select: 5 */ //
#define ADC12DIV_6 (6*0x20u) /* ADC12 Clock Divider Select: 6 */ //
#define ADC12DIV_7 (7*0x20u) /* ADC12 Clock Divider Select: 7 */ //clk/8
#define SHS_0 (0*0x400u) /* ADC12 Sample/Hold Source: 0 */ //ADC12SC
#define SHS_1 (1*0x400u) /* ADC12 Sample/Hold Source: 1 */ //TA.OUT1
#define SHS_2 (2*0x400u) /* ADC12 Sample/Hold Source: 2 */ //TB.OUT1
#define SHS_3 (3*0x400u) /* ADC12 Sample/Hold Source: 3 */ //TB.OUT2
#define CSTARTADD_0 (0*0x1000u) /* ADC12 Conv