毕业设计/论文
外文文献翻译系别自动化系
专业班级机械电子工程0603班
姓名
评分
指导教师
2010 年4月29日
毕业设计/论文外文文献翻译要求：
1．外文文献翻译的内容应与毕业设计/论文课题相关。
2．外文文献翻译的字数：非英语专业学生应完成与毕业设计/论文课题内容相关的不少于2000汉字的外文文献翻译任务（其中，汉语言文学专业、艺术类专业不作要求），英语专业学生应完成不少于2000汉字的二外文献翻译任务。格式按《华中科技大学武昌分校本科毕业设计/论文撰写规范》的要求撰写。
3．外文文献翻译附于开题报告之后：第一部分为译文，第二部分为外文文献原文，译文与原文均需单独编制页码（底端居中）并注明出处。本附件为封面，封面上不得出现页码。4．外文文献翻译原文由指导教师指定，同一指导教师指导的学生不得选用相同的外文原文。
驱动桥设计
随着汽车对安全、节能、环保的不断重视，汽车后桥作为整车的一个关键部件，其产品的质量对整车的安全使用及整车性能的影响是非常大的，因而对汽车后桥进行有效的优化设计计算是非常必要的。
驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩,并将动力合理地分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直力力和横向力。驱动桥一般由主减速器、差速器、车轮传动装置和驱动桥壳等组成。
驱动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载重汽车显得尤为重要。驱动桥设计应当满足如下基本要求：
1、符合现代汽车设计的一般理论。
2、外形尺寸要小，保证有必要的离地间隙。
3、合适的主减速比，以保证汽车的动力性和燃料经济性。
4、在各种转速和载荷下具有高的传动效率。
5、在保证足够的强度、刚度条件下，力求质量小，结构简单，加工工艺性
好，制造容易，拆装，调整方便。
6、与悬架导向机构运动协调，对于转向驱动桥，还应与转向机构运动协调。智能电子技术在汽车上得以推广使得汽车在安全行驶和其它功能更上一层楼。通过各种传感器实现自动驾驶。除些之外智能汽车装备有多种传感器能充分感知交通设施及环境的信息并能随时判断车辆及驾驶员是否处于危险之中，具备自主寻路、导航、避撞、不停车收费等功能。有效提高运输过程中的安全，减少驾驶员的操纵疲劳度，提高乘客的舒适度。当然蓄电池是电动汽车的关键，电动汽车用的蓄电池主要有：铅酸蓄电池、镍镉蓄电池、钠硫蓄电池、钠硫蓄电池、锂电池、锌—空气电池、飞轮电池、燃料电池和太阳能电池等。在诸多种电池中，燃料电池是迄今为止最有希望解决汽车能源短缺问题的动力源。燃料电池具有高效无污染的特性，不同于其他蓄电池，其不需要充电，只要外部不断地供给燃料，就能连续稳定地发电。燃料电池汽车(FCEV)具有可与内燃机汽车媲美的动力性能，在排放、燃油经济性方面明显优于内燃机车辆。
另外，设计必须得考虑所选择材料的可加工性能。一种材料的可机加工性通常以四种因素的方式定义：
1、分的表面光洁性和表面完整性。
2、刀具的寿命。
3、切削力和功率的需求。
4、切屑控制。
以这种方式，好的可机加工性指的是好的表面光洁性和完整性，长的刀具寿命，低的切削力和功率需求。关于切屑控制，细长的卷曲切屑，如果没有被切割成小片，以在切屑区变的混乱，缠在一起的方式能够严重的介入剪切工序。
因为剪切工序的复杂属性，所以很难建立定量地释义材料的可机加工性的关系。在制造厂里，刀具寿命和表面粗糙度通常被认为是可机加工性中最重要的因素。尽管已不再大量的被使用，近乎准确的机加工率在以下的例子中能够被看到。
通常，零件的可机加工性能是根据以下因素来定义的：表面粗糙度，刀具的寿命，切削力和功率的需求以及切屑的控制。材料的可机加工性能不仅取决于起内在特性和微观结构，而且也依赖于工艺参数的适当选择与控制。
拖臂悬架
结合起来的一种行为,semi-trailing-arm落后表现出轴。它是用来驱动的汽车前面。如果轴经验,它就像一卷悬垂态的手臂。扭转刚度的摩天大楼,这活象一个stabiliser酒吧。如果两个轮子的旅行经历相同的悬架(例如在球场的汽车)轴表现得像个拖臂悬架。
梁式轴(Four-Link-Style)
前面的一辆汽车后轴,不必有相同的高度为他们的卷中心。辊轴轴线上,这是经过辊子的中心——和后轴,看到前面的图。
辊轴
如果一个横向力的重心,导致层(fom)上面的重心轴的卷必须补偿片刻所致。由于一些弹簧悬辊。这一刻之间分配方面和后桥有赖于相对弹簧刚度的前面,与后轴,整体侧倾角(这是一样的,和后轴)取决于总和的悬架刚度(前加上后方)。传送到地面的瞬间,没有任何卷的整体车辆通过应用侧向力轴向前滚动的位置(在CG)。(注:如果滚动的轴,剩下的扭矩,CG必须补偿汽悬泉会像一辆摩托车内倾斜。这一幕的分布与后轴会,计算了
分别计算各轴的位置,by-using相应的axle-using卷中心的一部分的事实,轮轴横向力所承受的一部分,与正常负荷、轮轴必须随身携带
不同的例子
一个有限的特点,防滑差速器有点不同,不同的风格，一个自锁装置。
这个Torsen?风格差异;(从扭矩遥感)行为非常快(并可能严厉的)。在较低的输入扭矩的差动齿轮只是轻轻负载和移动，自由敞开的装置。随着力矩和速度起落架网格，大米和两个输出轴锁在一起。扭矩比(high-torque-wheel除以low-torque-wheel)不等,2.5:1 max。7:1,Torsen II的风格，从3:1来1.8:1(根据齿轮,齿轮表面处理的角度,类型的滚子轴承(平原,…)
达纳Trac-Loc?limited-slip差的(见图)包含一些预紧
通过弹簧离合器片、贝尔维尔)提供了一定的静态启动扭矩已经在零输入扭矩。蜘蛛齿轮,齿轮啮合侧设计那样(楔形齿),增加输入扭矩将增加的负担,提高离合器盘的锁轴。
独立的粘性微分锁的扭矩,但反应速度与输出轴之间的差异。包括离合器片没有机械接触,但是很紧的间隙,使粘滞摩擦提供扭矩的转让。注意,粘稠的差距在很光滑,有一定的时间延迟,作为粘度增加与所产生的热量(指的是特殊的液体是合宜的齿厚)。这使得操作容易使用汽车(虽然可以街是太慢了有些应用)。
Design of driving axle
As the car to safety, energy saving, the constant attention to environmental protection, vehicle after vehicle bridge as a key component, the quality of their products on the safe use of cars and car performance of a very large, so the car after Bridge Effectively optimize the design and calculation is very necessary.
Drive Bridge at the end of powertrain, its basic function is to increase came from the drive shaft or transmission of torque and power reasonably allocated to the left and right driving wheel and also bear in the role of the road and trailers or Body of power between the vertical and horizontal force. Drive from the main bridge general reducer, differential and the wheels, transmission and drive axle components, such as Shell. Bridge drive a vehicle with one of the four trains, its performance will have a direct impact on vehicle performance, and it is particularly important for the truck. Drive bridge should be designed to meet the following basic requirements:
a) a suitable main slowdown than to ensure that the car from the best power and fuel economy.
b) small form factor to ensure that the necessary ground clearance.
c) transmission gears and other parts of a smooth, noise.
d) in various load and speed of transmission with high efficiency.
e) to ensure adequate strength, stiffness conditions, should strive for the quality of small, in particular the quality of the spring as possible, to improve the car ride.
f) suspension and body-oriented movement coordination, the drive to the bridge, should also be coordinated with the campaign steering mechanism.
g) simple structure, processing technology and good, easy to manufacture, enables easy adjustment..
Intelligent electronic technology in the bus to promote safe driving and that the other functions. The realization of automatic driving through various sensors. Except some smart cars equipped with multiple outside sensors can fully perception of information and traffic facilities and to judge whether the vehicles and drivers in danger, has the independent pathfinding, navigation, avoid bump, no parking fees etc. Function.
Effectively improve the safe transport of manipulation, reduce the pilot fatigue, improve passenger comfort. Of course battery electric vehicle is the key, the electric car battery mainly has: the use of lead-acid batteries, nickel cadmium battery, the battery, sodium sulfide sodium sulfide lithium battery, the battery, the battery, the flywheel zinc - air fuel cell and solar battery, the battery. In many kind of cells, the fuel cell is by far the most want to solve the problem of energy shortage car. Fuel cells have high pollution characteristics, different from other battery, the battery, need not only external constantly supply of fuel and electricity can continuously steadily. Fuel cell vehicles (FCEV) can be matched with the car engine performance and fuel economy and emission in the aspects of superior internal-combustion vehicles.
Keyword: drive axle differential bridge reducer Bridge shell
This is an ANSYS optimum design for driving axle housing of a off-road vehicle. Firstly, the author established a three-dimensional model of the driving axle. States of stress in different working conditions were analyzed. Furthermore, the maximum pressure of driving axle was achieved.
And then, the three-dimensional model was imported into ANSYS, with some other manipulations, such as meshing, adding degree of freedom, applying surface loads, etc. States of stress of driving axle were calculated with the results exported.
Finally, this paper carried out the optimum design according to the target of minimizing the qualitative properties and homogenizing the distribution of stresses. The Confirmatory analysis showed that this design measured up to the engineering requirement.
MACHINABILITY
The machinability of a material usually defined in terms of four factors:
1、Surface finish and integrity of the machined part;
2、Tool life obtained;
3、Force and power requirements;
4、Chip control.
Thus, good machinability good surface finish and integrity, long tool life, and low force And power requirements. As for chip control, long and thin (stringy) cured chips,
if not broken up, can severely interfere with the cutting operation by becoming entangled in the cutting zone.
Because of the complex nature of cutting operations, it is difficult to establish relationships that quantitatively define the machinability of a material. In manufacturing plants, tool life and surface roughness are generally considered to be the
most
important factors in machinability. Although not used much any more, approximate machinability ratings are available in the example below.
SUMMARY
Machinability is usually defined in terms of surface finish, tool life, force and power requirements, and chip control. Machinability of materials depends not only on their intrinsic properties and microstructure, but also on proper selection and control of process variables.
A combination of trailing- and semi-trailing-arm behaviour shows the following axis. It is used for front driven cars only. If the axle experiences roll, it behaves like a
semi-trailing arm. The torsional stiffness counteracts the roll, by this acting like a stabiliser bar. If both wheels experience the same suspension travel (e.g. during pitch of the car) the axle behaves like a trailing arm suspension.
Beam Type Axle (Four-Link-Style)
Front- and rear-axle of a car needn't have the same hight for their roll center. The roll axis is that axis, that goes through the roll center of front- and rear-axle, see following drawing:
Roll Axis
If a lateral force is applied at the center of gravity, the moment resulting fom the hight of
the center of gravity above the roll axis has to be compensated by a moment caused by the
suspension springs due to some roll. The distribution of this moment between front- and rear axle depends on the relative spring stiffness of front- and rear-axle, the overall roll angle (which is the same for front- and rear-axle) depends on the sum of the suspension stiffness (front plus rear).
The moment transmitted to the ground without any roll for the overall vehicle is given by
the applied lateral force times the roll axis hight (at the position of CG). (Remark: If the
roll axis is above the CG, the remaining torque that has to be compensated by the suspension springs would make the car lean inside like a motorcycle!).
The distribution of this moment between front- and rear-axle can be calculated by calculating each axle seperately, by-using the position of the roll center of the corresponding axle-using the fact that the part of lateral force, that the axle has to carry,
corresponds to the part of the
normal load, the axle has to
carry
Differential Examples
The characteristics of a limited
slip differential are a little bit
different for different styles
of a self-locking device.
The Torsen? style
differentials (from TORque
SENsing) act very fast (and
possibly
harsh). Under low input torque the differential gears are only lightly loaded and move
freely like an open device. With increasing torque (and speed) the gear meshes are loaded up and the two output shafts are locked together. The torque ratio
(high-torque-wheel divided by low-torque-wheel) varies from max. 7:1 to 2.5:1, for the Torsen II style
from 3:1 to 1.8:1 (depending on gear angles, gear surface treatment, type of
bearing(plain, roller...)
The Dana Trac-Loc? limited-slip differential (see picture below) contains some preloaded
(by Belleville springs) clutch plates, which provide a certain static breakout torque already at zero input torque. The spider gear and side gear mesh are designed in that way (with wedge-shaped gear teeth), that increasing input torque will increase the load on the clutch plates, by this increasing the locking of the axle.
Dana Trac-Loc? limited-slip differential
The viscous differential locks independent of of torques, but reacts to the speed differences between the output shafts. The contained clutch plates have no mechanical contact, but very tight clearances, so that the viscous friction provides the torque transfer. Note that viscous differentials set in very smooth, and with a certain time delay, as the
viscosity increases with the
generated heat (means the special
fluid is becoming
'thicker'). This makes the
handling easier for street use cars
(while may be too slow for
some racing applications).
桥梁工程毕业设计外文翻译箱梁
西南交通大学本科毕业设计（论文） 外文资料翻译 年级: 学号: 姓名: 专业: 指导老师:
6 月
外文资料原文： 13 Box girders 13.1 General The box girder is the most ?exible bridge deck form. It can cover a range of spans from25 m up to the largest non-suspended concrete decks built, of the order of 300 m. Single box girders may also carry decks up to 30 m wide. For the longer span beams, beyond about 50 m, they are practically the only feasible deck section. For the shorter spans they are in competition with most of the other deck types discussed in this book. The advantages of the box form are principally its high structural ef?ciency (5.4), which minimises the prestress force required to resist a given bending moment, and its great torsional strength with the capacity this gives to re-centre eccentric live loads, minimising the prestress required to carry them.
外文出处： 《Exploiting Software How to Break Code》By Greg Hoglund, Gary McGraw Publisher : Addison Wesley Pub Date : February 17, 2004 ISBN : 0-201-78695-8 译文标题： JDBC接口技术 译文： JDBC是一种可用于执行SQL语句的JavaAPI（ApplicationProgrammingInterface应用程序设计接口）。它由一些Java语言编写的类和界面组成。JDBC为数据库应用开发人员、数据库前台工具开发人员提供了一种标准的应用程序设计接口，使开发人员可以用纯Java语言编写完整的数据库应用程序。 一、ODBC到JDBC的发展历程 说到JDBC，很容易让人联想到另一个十分熟悉的字眼“ODBC”。它们之间有没有联系呢？如果有，那么它们之间又是怎样的关系呢？ ODBC是OpenDatabaseConnectivity的英文简写。它是一种用来在相关或不相关的数据库管理系统（DBMS）中存取数据的，用C语言实现的，标准应用程序数据接口。通过ODBCAPI，应用程序可以存取保存在多种不同数据库管理系统（DBMS）中的数据，而不论每个DBMS使用了何种数据存储格式和编程接口。 1．ODBC的结构模型 ODBC的结构包括四个主要部分：应用程序接口、驱动器管理器、数据库驱动器和数据源。应用程序接口：屏蔽不同的ODBC数据库驱动器之间函数调用的差别，为用户提供统一的SQL编程接口。 驱动器管理器：为应用程序装载数据库驱动器。 数据库驱动器：实现ODBC的函数调用，提供对特定数据源的SQL请求。如果需要，数据库驱动器将修改应用程序的请求，使得请求符合相关的DBMS所支持的文法。 数据源：由用户想要存取的数据以及与它相关的操作系统、DBMS和用于访问DBMS的网络平台组成。 虽然ODBC驱动器管理器的主要目的是加载数据库驱动器，以便ODBC函数调用，但是数据库驱动器本身也执行ODBC函数调用，并与数据库相互配合。因此当应用系统发出调用与数据源进行连接时，数据库驱动器能管理通信协议。当建立起与数据源的连接时，数据库驱动器便能处理应用系统向DBMS发出的请求，对分析或发自数据源的设计进行必要的翻译，并将结果返回给应用系统。 2．JDBC的诞生 自从Java语言于1995年5月正式公布以来，Java风靡全球。出现大量的用java语言编写的程序，其中也包括数据库应用程序。由于没有一个Java语言的API，编程人员不得不在Java程序中加入C语言的ODBC函数调用。这就使很多Java的优秀特性无法充分发挥，比如平台无关性、面向对象特性等。随着越来越多的编程人员对Java语言的日益喜爱，越来越多的公司在Java程序开发上投入的精力日益增加，对java语言接口的访问数据库的API 的要求越来越强烈。也由于ODBC的有其不足之处，比如它并不容易使用，没有面向对象的特性等等，SUN公司决定开发一Java语言为接口的数据库应用程序开发接口。在JDK1．x 版本中，JDBC只是一个可选部件，到了JDK1．1公布时，SQL类包（也就是JDBCAPI）
驱动桥设计 随着汽车对安全、节能、环保的不断重视，汽车后桥作为整车的一个关键部件，其产品的质量对整车的安全使用及整车性能的影响是非常大的，因而对汽车后桥进行有效的优化设计计算是非常必要的。 驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩,并将动力合理地分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直力力和横向力。驱动桥一般由主减速器、差速器、车轮传动装置和驱动桥壳等组成。 驱动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载重汽车显得尤为重要。驱动桥设计应当满足如下基本要求： 1、符合现代汽车设计的一般理论。 2、外形尺寸要小，保证有必要的离地间隙。 3、合适的主减速比，以保证汽车的动力性和燃料经济性。 4、在各种转速和载荷下具有高的传动效率。 5、在保证足够的强度、刚度条件下，力求质量小，结构简单，加工工艺性 好，制造容易，拆装，调整方便。 6、与悬架导向机构运动协调，对于转向驱动桥，还应与转向机构运动协调。智能电子技术在汽车上得以推广使得汽车在安全行驶和其它功能更上一层楼。通过各种传感器实现自动驾驶。除些之外智能汽车装备有多种传感器能充分感知交通设施及环境的信息并能随时判断车辆及驾驶员是否处于危险之中，具备自主寻路、导航、避撞、不停车收费等功能。有效提高运输过程中的安全，减少驾驶员的操纵疲劳度，提高乘客的舒适度。当然蓄电池是电动汽车的关键，电动汽车用的蓄电池主要有：铅酸蓄电池、镍镉蓄电池、钠硫蓄电池、钠硫蓄电池、锂电池、锌—空气电池、飞轮电池、燃料电池和太阳能电池等。在诸多种电池中，燃料电池是迄今为止最有希望解决汽车能源短缺问题的动力源。燃料电池具有高效无污染的特性，不同于其他蓄电池，其不需要充电，只要外部不断地供给燃料，就能连续稳定地发电。燃料电池汽车(FCEV)具有可与内燃机汽车媲美的动力性能，在排放、燃油经济性方面明显优于内燃机车辆。
附录A 英文文献 Drive Axle All vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road. Powerflow The drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels. This is accomplished by a pinion drive gear, which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels. Rear-wheel drive Rear-wheel-drive vehicles are mostly trucks, very large sedans and many sports car and coupe models. The typical rear wheel drive vehicle uses a front mounted engine and transmission assemblies with a driveshaft coupling the transmission to the rear drive axle. Drive in through the layout of the bridge, the bridge drive shaft arranged vertically in the same vertical plane, and not the drive axle shaft, respectively, in their own sub-actuator with a direct connection, but the actuator is located at the front or the back of the adjacent shaft
外文翻译 专业机械设计制造及其自动化学生姓名刘链柱 班级机制111 学号1110101102 指导教师葛友华
外文资料名称： Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处：Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件： 1.外文资料翻译译文 2.外文原文
应用旋风技术真空吸尘器的设计和性能介绍 吉尔泰金，洪城铱昌，宰瑾李， 刘链柱译 摘要：旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率，压降，并切成尺寸被粒度对应于分级收集的50％的效率进行了研究。颗粒切成大小降低入口面积，体直径，减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法，用于收集在家庭中产生的粉尘。 摘要及关键词：吸尘器; 粉尘; 旋风分离器 引言 我们这个时代的很大一部分都花在了房子，工作场所，或其他建筑，因此，室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物，毒物，食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤，预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中，吸入压力下降说唱空转成比例地清洗的时间，以及纸过滤器也应定期更换，由于压力下降，气味和细菌通过纸过滤器内的残留粉尘。 图1示出了大气气溶胶的粒度分布通常是双峰形，在粗颗粒（>2.0微米）模式为主要的外部来源，如风吹尘，海盐喷雾，火山，从工厂直接排放和车辆废气排放，以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式，典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克，可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。
汽车设计课程设计说明书 题目：BJ130驱动桥部分设计验算与校核 姓名： 学号： 专业名称：车辆工程 指导教师： 目录 一、课程设计任务书 (1) 二、总体结构设计 (2) 三、主减速器部分设计 (2) 1、主减速器齿轮计算载荷的确定 (2) 2、锥齿轮主要参数选择 (4) 3、主减速器强度计算 (5) 四、差速器部分设计 (6) 1、差速器主参数选择 (6) 2、差速器齿轮强度计算 (7) 五、半轴部分设计 (8) 1、半轴计算转矩Tφ及杆部直径 (8) 2、受最大牵引力时强度计算 (9) 3、制动时强度计算 (9) 4、半轴花键计算 (9) 六、驱动桥壳设计 (10) 1、桥壳的静弯曲应力计算 (10) 2、在不平路面冲击载荷作用下的桥壳强度计算 (11) 3、汽车以最大牵引力行驶时的桥壳强度计算 (11) 4、汽车紧急制动时的桥壳强度计算 (12)
5、汽车受最大侧向力时的桥壳强度计算 (12) 七、参考书目 (14) 八、课程设计感想 (15)
一、课程设计任务书 1、题目 《BJ130驱动桥部分设计验算与校核》 2、设计内容及要求 （1）主减速器部分包括：主减速器齿轮的受载情况；锥齿轮主要参数选择；主减速器强度计算；齿轮的弯曲强度、接触强度计算。 （2）差速器：齿轮的主要参数；差速器齿轮强度的校核；行星齿轮齿数和半轴齿轮齿数的确定。 （3）半轴部分强度计算：当受最大牵引力时的强度；制动时强度计算。 （4）驱动桥强度计算：①桥壳的静弯曲应力 ②不平路载下的桥壳强度 ③最大牵引力时的桥壳强度 ④紧急制动时的桥壳强度 ⑤最大侧向力时的桥壳强度 3、主要技术参数 轴距L=2800mm 轴荷分配：满载时前后轴载1340/2735(kg) 发动机最大功率：80ps n：3800-4000n/min 发动机最大转矩17.5kg﹒m n：2200-2500n/min 传动比：i1=7.00； i0=5.833 轮毂总成和制动器总成的总重：g k=274kg
As the bearing cage rotates, read the value 7. indicated on the scale. Preload normally is specified as torque re-8. quired to rotate the pinion bearing cage, so take a reading only when the cage is rotating. Starting torque will give a false reading. To calculate the preload torque, measure the 9. diameter of the bearing cage where the cord was wound. Divide this dimension in half to get the radius. 10. U se the following procedure to calculate the bearing preload torque:Standard. Pull (lb) 3 radius (inches) 5 preload (lb-in.)or Preload (lb-in.) 3 0.113 (a conversion constant) 5 preload (N .m) Install the yoke, flat washer, and nut. Tighten 6. the nut snugly. Tap the end of the input shaft lightly to seat the bearings. Measure the input shaft endplay again with 7. the dial indicator. If endplay is still incorrect, repeat steps 3 through 7. With the endplay correct, seal the shim pack 8. to prevent lube leakage. Then torque the i nput shaft nut and cover capscrews to the correct value. 24.5 A XLE ADJUSTMENTS AND CHECKS This section introduces the differential carrier adjust-ments, checks, and tests that the truck technician must be capable of performing; some have been r eferred to previously in the text. For the most part, the procedures described here are general in nature. The truck technician should refer to OEM service l iterature for specific procedures.PINION BEARING PRELOAD Most differential carriers are provided with a press-fit outer bearing on the drive pinion gear. Some older rear drive axles use an outer bearing, which slips over the drive pinion. The procedures for adjusting both types follow. Press-Fit Method Adjustment To adjust the pinion bearing preload using the press-fit method, use the following procedure: Assemble the pinion bearing cage, bearings, 1. spacer, and spacer washer (without drive pin-ion or oil seal). Center the bearing spacer and spacer washer between the two bearing cones (Figure 24–49). When a new gear set or pinion bearings are 2. used, select a nominal size spacer based on OEM specifications. If original parts are used, use a spacer removed during disassembly of the drive. Place the drive pinion and cage assembly in a 3. press, with the gear teeth toward the bottom.Apply and hold the press load to the pinion 4. bearing. As pressure is applied, rotate the bearing cage several times so that the bear-ings make normal contact. While pressure is held against the assembly, wind 5. a cord around the bearing cage several times.Attach a spring scale to the end of the cord 6. (Figure 24–50). Pull the cord with the scale on a horizontal line. FIGURE 24–49 Assembly of the pinion bearing cage. (Courtesy of Dana Corporation) FIGURE 24–50 Cage in press to check bearing p reload. Sleeve must apply
附录I Drive axle powertrain at the end of their basic function is to increase the transmission came from the drive shaft or torque, and a reasonable distribution of power to the left and right wheel, in addition to acting on the road and under the frame or body legislation between the vertical, longitudinal and lateral force. General from the main drive axle reducer, differential, gear wheels and drive axle housings and other components. The design of the Drive axle: Drive axle should be designed to meet the basic requirements are as follows: 1. Select the main reduction ratio should be able to ensure the car has the best power and fuel economy. 2. Smaller size, to ensure that the necessary ground clearance. 3. Gear and other pieces of the work of a smooth transmission,and small noise. 4. In a variety of speed and load with a high transmission efficiency. 5. In ensuring adequate strength and stiffness conditions, should strive for the quality of small, especially under the mass-spring should be as small as possible in order to improve vehicle ride comfort. 6. And suspension movement-oriented coordination of steering drive axle, but also with the coordination of steering movement. 7. The structure of simple, good processing, manufacturing, easy disassembly, to facilitate adjustment. Drive axle classification -1-
毕业设计（论文） 外文翻译 题目西安市水源工程中的 水电站设计 专业水利水电工程 班级 学生 指导教师 2016年
研究钢弧形闸门的动态稳定性 牛志国 河海大学水利水电工程学院，中国南京，邮编210098 nzg_197901@https://www.doczj.com/doc/429091449.html,，niuzhiguo@https://www.doczj.com/doc/429091449.html, 李同春 河海大学水利水电工程学院，中国南京，邮编210098 ltchhu@https://www.doczj.com/doc/429091449.html, 摘要 由于钢弧形闸门的结构特征和弹力，调查对参数共振的弧形闸门的臂一直是研究领域的热点话题弧形弧形闸门的动力稳定性。在这个论文中，简化空间框架作为分析模型，根据弹性体薄壁结构的扰动方程和梁单元模型和薄壁结构的梁单元模型，动态不稳定区域的弧形闸门可以通过有限元的方法，应用有限元的方法计算动态不稳定性的主要区域的弧形弧形闸门工作。此外，结合物理和数值模型，对识别新方法的参数共振钢弧形闸门提出了调查，本文不仅是重要的改进弧形闸门的参数振动的计算方法，但也为进一步研究弧形弧形闸门结构的动态稳定性打下了坚实的基础。 简介 低举升力，没有门槽，好流型，和操作方便等优点，使钢弧形闸门已经广泛应用于水工建筑物。弧形闸门的结构特点是液压完全作用于弧形闸门，通过门叶和主大梁，所以弧形闸门臂是主要的组件确保弧形闸门安全操作。如果周期性轴向载荷作用于手臂，手臂的不稳定是在一定条件下可能发生。调查指出:在弧形闸门的20次事故中，除了极特殊的破坏情况下，弧形闸门的破坏的原因是弧形闸门臂的不稳定;此外，明显的动态作用下发生破坏。例如:张山闸，位于中国的江苏省，包括36个弧形闸门。当一个弧形闸门打开放水时，门被破坏了，而其他弧形闸门则关闭，受到静态静水压力仍然是一样的，很明显，一个动态的加载是造成的弧形闸门破坏一个主要因素。因此弧形闸门臂的动态不稳定是造成弧形闸门(特别是低水头的弧形闸门)破坏的主要原是毫无疑问。
驱动桥设计 摘要 现代工程车辆技术追求高效节能、高舒适性和高安全性等目标。前一项目标与环境保护密切相关,是当代全球性热门话题,后两项目标是车辆朝着高性能化方向发展必须研究和解决的重要课题。转向系统的高性能化是指其能够根据车辆的运行状况和驾驶员的要求实行多目标控制,以获得良好的转向轻便性、较好的路感和较快的响应性。 汽车转向系统是影响汽车操纵稳定性、行驶安全性和驾驶舒适性的关键部分。在追求高效节能\高舒适性和高安全性的今天,电控液压助力转向系统作为一种新的汽车动力转向系统,以其节能、环保、更佳的操纵特性和转向路感,成为动力转向技术研究的焦点。 本文通过查阅相关的文献，介绍了EHPS系统的结构组成和工作原理，在参考现有车型的结构数据的基础上，设计计算转向系的主要参数，确定转向器的结构参数和动力转向部分结构参数，在分析其助力特性的基础上，设计合理的助力特性曲线，并通过MATLAB作出助力特性图，同时提出一种基于车速和转向盘转动角速度的控制策略，根据EHPS系统的特点，通过AMESim和Simulink建立整个系统的模型。通过联合仿真可以得出EHPS系统比HPS系统能提供更好的助力特性和转向路感。 关键词：EHPS；助力特性；结构设计；AMESim与Simulink建模 ABSTRACT
High effective energy saving,high comfort performance and high security are thegoals of contemporary.The first goal closely concerns with environment protecting,is also the popular topic around the world.The last two goals are the important subjects must be researched and solved in making automobile high performance.To make the steering system high performance is that the system can carry out mufti-goals control according to the vehicle states and drive requirements to acquire the steering handiness,better road feeling,better anti-interfering performance and faster response. The motor turing system is the essential part which affects the automobile operation stability,the travel security and the driving comfortablet.Nowadays we pursue highly effective energy conservation,the high comforrtableness and high secure.The electrically hydraulic power steering (EHPS) taking as one kind of new automobile power steering system,it takes the power steering engineering research the focal point by its energy conservation,the environmental protection,the better handling characteristic and changes the road feeling. According to consult relevant literature, this paper introduces the structure and the principle of EHPS, bases the further study of EHPS on the structural parameter date of a certain type of the light lorry, calculates the main parameters of steering system and power steering and devises the hydraulic circuit of EHPS. On the basis of the analysis of EHPS, this paper designs a reasonable EHPS power curve, including plotting the curve with the technique of MATLAB. Taking into account the steady steering and emergency steering, it advances the control strategy plan based on speed, steering wheel angle velocity, the steering wheel torque. Based on the structural characteristics of EHPS, this paper proposed AMESIM and SIMULINK joint simulation of the entire EHPS system. Accord to the result we can know that EHPS can offer more secure handle, more saving energy and way feeling. Key words:EHPS;Characteristics of power; Structure design; AMESim and Simulink Modeling
驱动桥设计外文翻译 驱动桥设计 随着汽车对安全、节能、环保的不断重视，汽车后桥作为整车的一个关键部件，其产品的质量对整车的安全使用及整车性能的影响是非常大的，因而对汽车后桥进行有效的优化设计计算是非常必要的。 驱动桥处于动力传动系的末端，其基本功能是增大由传动轴或变速器传来的转矩,并将动力合理地分配给左、右驱动轮，另外还承受作用于路面和车架或车身之间的垂直力力和横向力。驱动桥一般由主减速器、差速器、车轮传动装置和驱动桥壳等组成。 驱动桥作为汽车四大总成之一，它的性能的好坏直接影响整车性能，而对于载重汽车显得尤为重要。驱动桥设计应当满足如下基本要求: 1、符合现代汽车设计的一般理论。 2、外形尺寸要小，保证有必要的离地间隙。 3、合适的主减速比，以保证汽车的动力性和燃料经济性。 4、在各种转速和载荷下具有高的传动效率。 5、在保证足够的强度、刚度条件下，力求质量小，结构简单，加工工艺性 好，制造容易，拆装，调整方便。 6、与悬架导向机构运动协调，对于转向驱动桥，还应与转向机构运动协调。智能电子技术在汽车上得以推广使得汽车在安全行驶和其它功能更上一层楼。通过各种传感器实现自动驾驶。除些之外智能汽车装备有多种传感器能充分感知交通设施及环境的信息并能随时判断车辆及驾驶员是否处于危险之中，具备自主寻路、导航、避撞、不停车收费等功能。有效提高运输过程中的安全，减少驾驶员的操纵疲劳度，提高乘客的舒适度。当然蓄电池是电动汽车的关键，电动汽车用的蓄电池主
要有:铅酸蓄电池、镍镉蓄电池、钠硫蓄电池、钠硫蓄电池、锂电池、锌—空气电池、飞轮电池、燃料电池和太阳能电池等。在诸多种电池中，燃料电池是迄今为止最有希望解决汽车能源短缺问题的动力源。燃料电池具有高效无污染的特性，不同于其他蓄电池，其不需要充电，只要外部不断地供给燃料，就能连续稳定地发电。燃料电池汽车(FCEV)具有可与内燃机汽车媲美的动力性能，在排放、燃油经济性方面明显优于内燃机车辆。 这项发明通常涉及到多能源动力总成的车辆,以及,尤其是多能源动力总成,有多个电源包括电动马达来驱动的汽车轮子。混合动力电动动力系统已经被发展成为包括电机(IC)做内燃机引擎,自主经营的或者联合根据行驶条件下,国家费用的牵引电池,与电源,最有效地满足当前所产生的电力需求车辆操作。大部分电子混合动力汽车可以在市场上买到是前轮驱动车辆,只不过前轮带动起来的。混合动力电动动力系统被开发用于四轮驱动车,允许两个电机和引擎传送权力后方的驱动轮。当包装电动马达驱动后桥机组是较好的使用躺轴功率流,马达驱动单元被放在后桥中心线。这样的电的混合动力系统,然而,现在的包装设计很困难,特别是当副轴车辆传动是用来传输动力,纵向驱动轴后轴。需要混合动力电动存在的动力,在其中轴是靠电动机驱动的或的内燃机结合电机。以减少成本,电动机器将提供所有混合功能,包括电气能源的产生、电动汽车、电子发动机启动投放 提高发动机的功率,再生式制动。一个驱动器单位是混合动力电动汽车包括市场, 发动机,电动机器包括转子,副轴，齿轮组包括一个输入可驱动的连接到发动机和输出,用来传送之间权限投入与产出和生产第一速度微分导致一个录入速度超过每小时的速度输出,第一和第二驾车轴差动机构可驱动的连接到输出线时,因为传输功率和输出之间驾车轴,可驱动的行星齿轮装置连接到输出和转子,说之间权限传输转子和输出线,制作了第二速度微分导致转子速度超过速度输出。转矩反应为减速
毕业设计/论文 外文文献翻译 院系城市建设学院 专业班级 姓名 原文出处 评分 指导教师 华中科技大学武昌分校 20 12 年3月1日
Study on nonlinear analysis of a redundant cable-stayed bridge 1．Abstract A comparison on nonlinear analysis of a highly redundant cable-stayed bridge is performed in the study. The initial shapes including geometry and prestress distribution of the bridge are determined by using a two-loop iteration method, it is an equilibrium iteration loop and a shape iteration loop. For the initial shape analysis a linear and a nonlinear computation procedure are set up. In the former all nonlinearities of cable-stayed bridges are disregarded, and the shape iteration is carried out without considering equilibrium. In the latter all nonlinearities of the bridges are taken into consideration and both the equilibrium and the shape iteration are carried out. Based on the convergent initial shapes determined by the different procedures, the natural frequencies and vibration modes are then examined in details. Numerical results show that a convergent initial shape can be found rapidly by the two-loop iteration method, a reasonable initial shape can be determined by using the linear computation procedure, and a lot of computation efforts can thus be saved. There are only small differences in geometry and prestress distribution between the results determined by linear and nonlinear computation procedures. However, for the analysis of natural frequency and vibration modes, significant differences in the fundamental frequencies and vibration modes will occur, and the nonlinearities of the cable-stayed bridge response appear only in the modes determined on basis of the initial shape found by the nonlinear computation. 2. Introduction Rapid progress in the analysis and construction of cable-stayed bridges has been made over the last three decades. The progress is mainly due to developments in the fields of computer technology, high strength steel cables, orthotropic steel decks and construction technology. Since the first modern cable-stayed bridge was built in Sweden in 1955, their popularity has rapidly been increasing all over the world. Because of its aesthetic appeal, economic grounds and ease of erection, the
毕业设计（论文） 外文文献翻译 题目：A new constructing auxiliary function method for global optimization 学院： 专业名称： 学号： 学生姓名： 指导教师： 2014年2月14日
一个新的辅助函数的构造方法的全局优化 Jiang-She Zhang，Yong-Jun Wang https://www.doczj.com/doc/429091449.html,/10.1016/j.mcm.2007.08.007 非线性函数优化问题中具有许多局部极小，在他们的搜索空间中的应用，如工程设计，分子生物学是广泛的，和神经网络训练．虽然现有的传统的方法，如最速下降方法，牛顿法，拟牛顿方法，信赖域方法，共轭梯度法，收敛迅速，可以找到解决方案，为高精度的连续可微函数，这在很大程度上依赖于初始点和最终的全局解的质量很难保证．在全局优化中存在的困难阻碍了许多学科的进一步发展．因此，全局优化通常成为一个具有挑战性的计算任务的研究． 一般来说，设计一个全局优化算法是由两个原因造成的困难：一是如何确定所得到的最小是全球性的（当时全球最小的是事先不知道），和其他的是，如何从中获得一个更好的最小跳．对第一个问题，一个停止规则称为贝叶斯终止条件已被报道．许多最近提出的算法的目标是在处理第二个问题．一般来说，这些方法可以被类?主要分两大类，即：（一）确定的方法，及（ii）的随机方法．随机的方法是基于生物或统计物理学，它跳到当地的最低使用基于概率的方法．这些方法包括遗传算法（GA），模拟退火法（SA）和粒子群优化算法（PSO）．虽然这些方法有其用途，它们往往收敛速度慢和寻找更高精度的解决方案是耗费时间．他们更容易实现和解决组合优化问题．然而，确定性方法如填充函数法，盾构法，等，收敛迅速，具有较高的精度，通常可以找到一个解决方案．这些方法往往依赖于修改目标函数的函数“少”或“低”局部极小，比原来的目标函数，并设计算法来减少该?ED功能逃离局部极小更好的发现． 引用确定性算法中，扩散方程法，有效能量的方法，和积分变换方法近似的原始目标函数的粗结构由一组平滑函数的极小的“少”．这些方法通过修改目标函数的原始目标函数的积分．这样的集成是实现太贵，和辅助功能的最终解决必须追溯到