当前位置:文档之家› 机械术语中英文对照

机械术语中英文对照

机械术语中英文对照
机械术语中英文对照

机械术语中英文对照(一)

Piping work: 铺管工程

Steam trace: 加热蒸汽管道

Cutting: 切割

socket weld承插焊接

fillet weld角焊,填角焊

branch connection分支接续

fabrication tolerance.制造容差

local heat treatment 局部热处理

threaded pipe螺纹管

seal welding.密封焊接

flange joint 凸缘接头

undercut 底切

feeder馈电线

conduit outlet电线引出口

seal fitting 密封接头, 密封配件

Screw thread lubricant螺纹润滑剂

Seal: 绝缘层

weld reinforcement 焊缝补强

lock washer 锁紧[止动, 防松]垫圈

electrical panel.配电板,配电盘

nipple螺纹接头

zinc plated.镀锌的

ring joint 环接, 围缘接合

bolt 螺栓

control: 控制器

National Electrical Code 全国电气规程

master schedule 主要图表, 综合图表, 设计任务书, 主要作业表

torque wrench 转矩扳手

job site 施工现场

flange connection.凸缘联接

Hard hat:安全帽

Goggles:护目镜

stockpile贮存

packing list装箱单

crate: 柳条箱

purchased material list原材料进货单

back-feed反馈

wire coil线盘,线卷,

NPT thread. 美国标准锥管螺纹

cable gland 电缆衬垫

terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻

connector. 接线器

insulated sleeve绝缘套管

wire connector接线器

wire terminal电线接头

control wiring控制线路

motor lead电动机引出线

power wiring电力布线

tender document.提供证件

orifice plate.挡板

nut 螺母

flange gasket 法兰垫片

dimensional inspection 尺寸检验

burn through 烧蚀

piping system.管道系统

reinforcement of weld加强焊缝

fabrication.制造

dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验

girth weld环形焊缝

cement lined piping 水泥衬里

weld joint 焊缝, 焊接接头

spool drawing 管路图, 管路详图

spot test 抽查, 当场测试

butt weld 对接焊缝

Random Radiography随机射线照相检查

radiographic examination 射线照相检查assembly.装配

erection 架设

examination试验

cable tray.电缆盘

rigid steel conduit 钢制电线管

power control 功率控制

arc welding 电弧焊

control cable控制电缆操纵索

normal bend 法向[法线]弯管

cable glands: 电缆衬垫

exfoliation剥落

power receptacle 电力插座

grounding conductor 接地导体

lighting fixture照明器材

junction box 分线箱

race way 电缆管道

terminal box接线盒

distribution board配电盘, 配电屏

receptacle 插座

tumble switch.翻转开关,拨动式开关

cathodic protection system 阴极保护系统

Circuit breaker断路开关

amplifier panel 放大器盘

control console 控制台

electrical material电气材料

convenience receptacle.电源插座

cable gland 电缆衬垫

TIG: Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊

filler rod焊条

tensile strength 抗张强度

shield gas 保护气体

shield jig保护夹具

high frequency generator.高频发电机

welding rod 焊条

filler metal 焊料, 焊丝

shop fabrication 车间制造

field installation 现场安装

welding bead 焊道

both sides welding.双面焊接

residual stress 残余应力

electrode 电焊条

condensation 冷凝

longitudinal.纵向的

horizontal line 水平线

circumferential joint 周圈接缝

nondestructive examination.非破坏性检验,

qualification: 合格性

construction work施工工程

welded joint焊接缝焊接节点

gas cutti g.气割

arc cutting电弧切割

grind off 磨掉

metallic luster 金属光泽

Screwed Piping Joints螺丝状的管接头

gouging .刨削槽

当前位置:生命经纬 > 外语与术语 > 电子与机械英语 > 机械专业英语 > 文章正文

机械术语中英文对照(二)

Bending: 挠曲

witness test订货人在场的试验

Welding: 焊接

Threading: 车缧纹

Leveling:校平

color identification 彩色识别

Alignment:对准,定位调整

check against 检查, 核对

Fixing:固定

Console:控制台

cubicle室,箱

audit 审计

material certificate.材料合格证

vertical panel竖直面板

power distribution panel 配电盘

gauge board仪表板

beveling 磨斜棱,磨斜边

local panel 现场配电盘

grouting 灌浆

fabrication 加工,制造

instrument rack 计测器支架

tank gauge 液面计

flushing 冲洗,填缝

analyzer分析器

piping管道敷设

tubing敷设管道

cable fitting电缆配件

elbow.弯管接头

main pipe 主管道

bend.弯管弯头

solvent 溶剂

postweld heat treatment 焊后热处理

jig.夹具

arc gouging 电弧刨削

chipping修琢

machining 机械加工

bridges.管式桥

clamp.夹钳

tack welding 点焊

butt welding 对接焊

grinder. 磨床

commencement.开始

gusset plate角撑板, 加固板

process pipe 工艺管道

land 纹间表面

tee 三通管丁字钢 T形梁

opening 开口

reinforcing pad.补强垫,增强衬板

flux 焊剂

wet developer 湿显像剂

blowhole气泡,气孔

inclusion 杂质

imperfection 缺陷

limitation 限度

valve 阀,闸门

structural attachment 结构附件

tapered allowance 削尖余量

tack welding 平头焊接

sputter 喷溅

scale 废料

lateral translation侧向平移

weld joint 焊缝, 焊接接头

plug.塞

fusion 熔融

base material基底材料

lead foil 铅箔

intensifying screen 增光屏, 光增强屏pressure test.压力试验

film density.影片密度

line number行数

leak test漏泄试验

plate thickness 筛板厚度

restoration修理

field fabricated 工地制造的,现场装配的junction box.接线盒

flow sheet 流程图

vent 放气孔, 通风孔

drain 排水管

instrument air仪表气源

blind挡板

pipe arrangement 管配置

civil engineer.土木工程师

bus duct 母线槽

substation分站

flow instrument 流量计

power distribution panel 配电盘

level instrument 位面计, 水平仪

pressure instrument 压力仪表/压力计

level switch (信号)电平开关,

gage glass 液位玻璃管

pilot tube指示灯

line check 小检修

recalibration.复校,重新校准

blinding plate盲板

expansion joint 伸缩接头

hydrostatic pressure test静水压试验pneumatic pressure 气压

scaffolding脚手架

check valve止回阀

liquid penetrant examination液体渗透探伤test pump试验泵

witnessed inspections 现场检测

hanger吊架

control valve控制阀,

fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力

disposition notice 处罚通知书

pipe stanchion 管支柱

bellow type 波纹管式

expansion joint 伸缩接头

vibration stopper:减震器

subcontractor 转包商

WPS Works Process Specification 典型工艺规程piping.管道系统

flange.凸缘

sleeve 套筒

ferritic .铁素体的

identification mark 识别标志

stencil.模绘片版,镂花模板

stamping .冲压

silicone paint硅树脂油漆

weld bead 焊缝

automatic temperature recorder 温度自动记录器penetrameter 透度计

film viewer底片观察用光源

civil works土建工程,建筑工程

lump sum price 混合价格 ,统包价格

scrap material废料

caulking metal填隙合金[金属](材料) application drawing操作图, 应用图

cable routing电缆路由选择

channel bases沟渠基底

vertical panel竖直面板

local panel 现场配电盘

power distribution panel 配电盘

gauge board样板, 模板规准尺

anchor bolt 锚定螺栓

expansion bolt 伸缩栓, 扩开螺栓

field instrument.携带式仪表

instrument rack 计测器支架,计测器框架

tank gauge 油箱液位计

guide wire 尺度[定距]索,准绳

name plate名牌, 商标

lead pipe铅管

take-off valve输出阀

sub-header分联箱

air header 集气管

pneumatic signal气动信号

steam trace 加热蒸汽管道

electric heat tracing.电伴随加热

cable trunk 电缆管道

stop end封端

fire barriers防火间隔

bonding wire 接合线, 焊线

conduit box [电]导管分线匣

rigid conduits 刚性导管

flexible conduit软管

conduit entry 导管引入装置

road crossing duct bank平交道口管道组Capping ends顶盖末端

cable armor电缆铠装

Cable sheath电缆包皮层

sealing compound电缆膏

coaxial cable同轴电缆

loop test环路测试

sequence test.联锁顺序试验

lintel beam 水平横楣梁

flash plate闪熔镀层

anchor bolt 地脚螺栓

expansion bolt伸缩栓, 扩开螺栓

shim plate 垫板

push button station按钮式控制站

logic diagram逻辑图

calculation sheet计算书

flow instrument流量计

level instrument 位面计, 水平仪layout drawing 布置图

tie band捆扎用带材

Heating boxes加热室

cutting opening切孔

control valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计

odometer历程标

tachometer转速计

chronometer精密计时表

机械类常用英语词汇大全

机械类常用英语词汇大全 一字螺丝批 slot type screwdriver 一点透视 one-point perspective 二画 二合一黏合剂 epoxy resin adhesive 二合胶;混合胶 epoxy glue 二维的;平面的 two-dimensional 二进制 binary 二极管;整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的;公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学 ergonomics; human engineering 人体尺寸 human dimension 人体测量学 anthropometry; anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷;床鞍 apron 刀座鞍;溜板座 saddle 力 force 力三角形 triangle of force 力平行四边形 parallelogram of force 力多边形;多边形力学 polygon of force 力的分解 force resolution 力架;亮漆 lacquer 力矩 moment 力偶 couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip s head screw 十字螺丝批 Philip s type screwdriver 丁字尺;T 尺 tee square 三画 三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的;立体的 three-dimensional 三氯甲烷;哥罗芳 chloroform 三聚氰胺;蜜胺 melamine 三点透视 three-point perspective 上油漆 painting 上釉 enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力;虫漆 shellac 士巴拿;扳手 spanner 大芯夹板;宽条芯夹板 blockboard; solid corestock-laminated board 大量制造 mass production

机械专业相关词汇中英文翻译大全

机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus

机械术语英文翻译

机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ;normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ;Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch

社会学专业词汇中英文对照

(按中文拼音首字母排序) B 暴民:mob 比拟法:analogical method 比例抽样:proportionate sample 不可知论:agnosticism 变态心理学:abnormal psychology 不完全归纳:incomplete induction 边际效用递减:law of diminishing marginal utility 柏拉图式爱情:Platonic love C 丛众:conformity 残疾人:the handicapped 参考书目:bibliography 参考群体:reference group 成人教育:adult education 初婚年龄:age at first marriage 垂直流动:vertical mobility 出身群体:descent group 抽样误差:sampling error 抽样范围:sampling frame 参与式观察:participant observation D 代沟:generation gap 对照分析:contrastive analysis 定性分析:qualititive analysis 定量分析:quantitative analysis 定额抽样:quota sample 多重人格:multiple personality 地位流动:status mobility 第一手资料:primary data 第二手资料:raw data 单因素实验:single-factor experiment 地域性流动:geographical mobility F 法人:fictitions person 反隔离:desegregation 犯罪学:criminology 父居家庭:patrilocal family 父系亲属:agnate 父子关系:filiation 分析性研究:analytical research 封闭式监管:close custody 封闭型问题:closed question 分层随机抽样:stratified random sample G 规范:norms 更年期:menopause 过激主义:ultraism 个案研究:case study 个人主义:individualism 归属需求:need to belong 个人崇拜:personality cult 功能主义:functionalism H 行话,黑话:argot 横坐标:abscissa 合理趋势:rational trend 霍桑效应:Hawthorne effect 婚姻调适:marriage adjustment 宏观分析:macroscopic analysis 黄金分割:golden section 互补角色:complementary role J 家谱:family religrees 截点:cut-off point 拒答率:refusal rate 绝对值:absolute value 监护人:chaperonage 角色冲突:role conflict 角色距离:role distance 角色紧张:role strain 金钱崇拜:mammon worship 间接暗示:indirect suggestion 价值中立:value free 价值判断:value judgement

机械工具英语词汇列表

机械工具 扳子spanner (美作:wrench) 敲击扳手Impact spanner 双头扳子double-ended spanner 活扳子,活络扳手adjustable spanner, monkey wrench 套筒扳手box spanner (美作:socket wrench) 卡规calipers 夹钳pincers, tongs 剪床/大剪刀shears 钢锯hacksaw 剪线钳wire cutters 万能手钳multipurpose pliers, universal pliers 可调手钳adjustable pliers 冲子punch 钻drill 麻花钻Twist drill 螺纹thread 丝锥threader 丝锥tap 板牙spanner 板牙mastertap 绞刀(扩孔钻) reamer 柱绞刀cylinder reamer 锥绞刀taper reamer 卡盘chuck 三角刮刀scraper 孔径规calliper gauge 铆钉rivet 螺母nut 自锁螺母,防松螺母locknut 螺栓bolt 销钉pin, peg, dowel 垫圈washer U形钉staple 注油枪grease gun 撬棍Tommy bar, crow bar 防震橡胶锤rubber dead blow hammer 手动葫芦(倒链) manual hoister 机械加工拋光polishing 安装to assemble 衬套bushing 半机械化semi-mechanization; semi-mechanized 半自动滚刀磨床semi-automatic hob grinder 滚刀hob 扳手wrench 1

建筑专业词汇中英对照(精心整理版)

1DESIGN BASIS 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design 2STAGE OF DESIGN 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing 3CLIMATE CONDITION 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning 飓风hurricane 台风typhoon 旋风cyclone 降雨强度rainfall intensity 年降雨量annual rainfall 湿球温度wet bulb temperature 干球温度dry bulb temperature 冰冻期frost period

机械英语词汇

整个注射过程: (四个油缸作用) clamp cylinder nozzle cylinder 锁模—(低压模保)—整前(喷嘴进)—(行程开关injection start)—injection cylinder 注射(螺杆进)—保压—储料(预塑/螺杆转)—(料自料斗进,料满后推动螺杆退,背压)—防流涎—同时冷却—整后(有时无)—开模— ejector cylinder 顶出(产品通过光电开关/电眼自动掉下)—顶退. TECHNICAL TERMS flat-head screw: 平头螺丝pan-head screw: 圆头螺丝 fixing screw: 托脚screwdriver: 螺丝刀 full thread: 全螺纹locknut: 紧定螺帽/螺母,紧母/迫母, tie rod nut: 调模丝母tie rod nut washer: 调模丝母垫 tie rod nut holder: 调模丝母压盖 bolt: n. 螺钉/螺栓; v,栓住, 定位stud bolt: 模具压板螺栓 hold-down bolt: 压紧装置/螺栓 jack bolt: 调节螺栓eye bolt: 吊环螺栓 countersink screw: 沉头螺钉fundation bolt: 地脚螺栓 Mold mounting bolt: 模具安装螺栓fastening bolt: 紧固螺钉anchoring hole/ foundation bolt hole: 地脚螺栓孔flight: 螺齿/导程secondary flight: 次螺槽primary flight: 主螺槽 channel: 槽, 通道screw land: 螺棱land:台面flute: 槽trough: 槽chute: 滑槽 coolant reservoir:冷却液槽T-slot: T型槽 screw axis: 螺轴pitch: 螺距(沥青), 螺牙(螺距= lead) screw speed: 螺杆转速 opposed semi-circular grooves: 对置式半环形键槽 Tangential groove: 切向键槽axial groove: 轴向键槽 Remedial groove: 修复式键槽stripping tank: 洗提槽 Spline: 花键key: 键membrane: 薄膜键 steel wadge: 钢契口grinding wheel: 砂轮emery cloth: 砂布main machine: 整机machine frame: 机器框架/机架 barrel base cover: 前板盖screw barrel: 机筒end cap: 前机筒

(完整word版)纺织机械专业术语大全及中英文对照,很有用,推荐文档

纺织机械专业术语大全及中英文对照,很有用! 导读 本文由钱苹生先生整理编辑,再次表示感谢!如需转载,请注明作者及来源,谢谢! 一、纺纱类机械: 1. 棉纺前纺机械Preparatory machinery for cotton spinningsystems 2. 轧花机Gins 3. 打包机 Baling presses4. 拆包机及抓包机Bale breakers, bale pluckers5. 清花间用机械Blow room machinery6. 混棉箱Blending hoppers7. 梳棉机自动喂棉机Automatic feeding devices for cardingmachines8. 梳棉机Carding machines9. 并条机Drawing frames10. 条卷机Sliver lap machines11. 精梳机Combing machines12. 粗纱机Speed frames13. 包纱机Covering machines14. 精梳毛纺、半精梳毛纺、毛纺前纺机械Preparatory machinery for worsted,semi-worsted or woolen spinning systems15. 羊毛开包机Wool bale brokers16. 洗毛生产机Wool washing lines17. 开松除杂机、和毛机、弹毛机willowingmachinery and teasers, garnet machines18. 废毛利用生产机Waste reclamation19. 梳毛机Carding machines20. 自动

软件工程专业词汇中英对照

软件工程专业词汇中英 对照 The manuscript was revised on the evening of 2021

Acceptance Testing--可接受性测试一般由用户/客户进行的确认是否可以接受一个产品的验证性测试。 actual outcome--实际结果被测对象在特定的条件下实际产生的结果。 Ad Hoc Testing--随机测试测试人员通过随机的尝试系统的功能,试图使系统中断。 algorithm--算法一个定义好的有限规则集,用于在有限步骤内解决一个问题;(2)执行一个特定任务的任何操作序列。 algorithm analysis--算法分析一个软件的验证确认任务,用于保证选择的算法是正确的、合适的和稳定的,并且满足所有精确性、规模和时间方面的要求。 Alpha Testing--Alpha测试由选定的用户进行的产品早期性测试。这个测试一般在可控制的环境下进行的。 analysis--分析分解到一些原子部分或基本原则,以便确定整体的特性;(2)一个推理的过程,显示一个特定的结果是假设前提的结果;(3)一个问题的方法研究,并且问题被分解为一些小的相关单元作进一步详细研究。 anomaly--异常在文档或软件操作中观察到的任何与期望违背的结果。 application software--应用软件满足特定需要的软件。 architecture--构架一个系统或组件的组织结构。 ASQ--自动化软件质量(Automated Software Quality)使用软件工具来提高软件的质量。 assertion--断言指定一个程序必须已经存在的状态的一个逻辑表达式,或者一组程序变量在程序执行期间的某个点上必须满足的条件。assertion checking--断言检查用户在程序中嵌入的断言的检查。 audit--审计一个或一组工作产品的独立检查以评价与规格、标准、契约或其它准则的符合程度。 audit trail --审计跟踪系统审计活动的一个时间记录。 Automated Testing--自动化测试使用自动化测试工具来进行测试,这类测试一般不需要人干预,通常在GUI、性能等测试中用得较多。 Backus-Naur Form--BNF范式一种分析语言,用于形式化描述语言的语法 baseline--基线一个已经被正式评审和批准的规格或产品,它作为进一步开发的一个基础,并且必须通过正式的变更流程来变更。 Basic Block--基本块一个或多个顺

机械专业术语英文翻译

机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker

各种专业名称英语词汇中英文对照表

各种专业名称英语词汇中英文对照表 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学(含税收学)Public Finance (including Taxation) 金融学(含保险学)Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law

机械术语中英文对照

机械术语中英文对照: Piping work: 铺管工程 Steam trace: 加热蒸汽管道 Cutting: 切割 socket weld承插焊接 fillet weld角焊,填角焊 branch connection分支接续 fabrication tolerance.制造容差 local heat treatment 局部热处理 threaded pipe螺纹管 seal welding.密封焊接 flange joint 凸缘接头 undercut 底切 feeder馈电线 conduit outlet电线引出口 seal fitting 密封接头, 密封配件 Screw thread lubricant螺纹润滑剂 Seal: 绝缘层 weld reinforcement 焊缝补强 lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘 nipple螺纹接头

zinc plated.镀锌的 ring joint 环接, 围缘接合 bolt 螺栓 control: 控制器 National Electrical Code 全国电气规程 master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手 job site 施工现场 flange connection.凸缘联接 Hard hat:安全帽 Goggles:护目镜 stockpile贮存 packing list装箱单 crate: 柳条箱 purchased material list原材料进货单 back-feed反馈 wire coil线盘,线卷, NPT thread. 美国标准锥管螺纹 cable gland 电缆衬垫 terminal block线弧, 接头排接线盒, 接线板, 线夹 power drill机械钻 connector. 接线器

机械专业英语词汇【完整版】

机械专业英语词汇 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck

机械行业专业英语词汇刀具类

金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半 导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 机械专业词汇:hardenability 淬透性carbide tool 硬质合金

统计学专业词汇中英对照

统计学专业词汇中英对照 Absolutedeviation,绝对离差 Absolutenumber,绝对数 Absoluteresiduals,绝对残差 Accelerationarray,加速度立体阵Accelerationinanarbitrarydirection,任意方向上的加速度Accelerationnormal,法向加速度Accelerationspacedimension,加速度空间的维数Accelerationtangential,切向加速度 Accelerationvector,加速度向量 Acceptablehypothesis,可接受假设 Accumulation,累积 Accuracy,准确度 Actualfrequency,实际频数 Adaptiveestimator,自适应估计量 Addition,相加 Additiontheorem,加法定理 Additivity,可加性 Adjustedrate,调整率 Adjustedvalue,校正值 Admissibleerror,容许误差 Aggregation,聚集性 Alternativehypothesis,备择假设 Amonggroups,组间 Amounts,总量 Analysisofcorrelation,相关分析 Analysisofcovariance,协方差分析 Analysisofregression,回归分析 Analysisoftimeseries,时间序列分析 Analysisofvariance,方差分析 Angulartransformation,角转换 ANOVA(analysisofvariance),方差分析 ANOVAModels,方差分析模型 Arcing,弧/弧旋 Arcsinetransformation,反正弦变换 Areaunderthecurve,曲线面积 AREG,评估从一个时间点到下一个时间点回归相关时的误差ARIMA,季节和非季节性单变量模型的极大似然估计Arithmeticgridpaper,算术格纸 Arithmeticmean,算术平均数 Arrheniusrelation,艾恩尼斯关系 Assessingfit,拟合的评估 Associativelaws,结合律

英文版机械专业术语(全)

组装、冲压、喷漆等专业词汇 Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 V oltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资 源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein|刨床 miller铣床 grinder磨床 driller钻床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |'skræpid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制 程不良 oxidation |' ksi'dein|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总 务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具

相关主题
相关文档 最新文档