当前位置:文档之家› 交换机配置文档

交换机配置文档

ESwitching Basic Switching/Wireless PT Practice SBA

A few things to keep in mind while completing this activity:

1. Do not use the browser Back button or close or reload any Exam windows during the

exam.

2. Do not close Packet Tracer when you are done. It will close automatically.

3. Click the Submit Assessment button to submit your work.

Introduction

In this practice Packet Tracer Skills Exam, you will:

?configure VLANs using VTP

?configure inter-VLAN routing

?modify STP

?configure port security

?add a wireless LAN

Addressing Table

Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.

Step 1: Connect the Devices.

Use the appropriate cable type to make the following connections:

?SW_AC2 FastEthernet 0/1 to PC1

?SW_AC2 FastEthernet 0/11 to PC2

?SW_AC2 FastEthernet 0/19 to SW_AC3 FastEthernet 0/19

?SW_AC2 FastEthernet 0/20 to SW_AC3 FastEthernet 0/20

?SW_AC3 FastEthernet 0/18 to WRS

Step 2: Configure the Device Basics.

a.Configure the following on SW_AC2.

?The switch name is SW_AC2.

?The privileged EXEC mode uses the following encrypted

password: class

?Enable Telnet and console line login using the following password: cisco

?Configure the banner message-of-the-day as Authorized access only!

b.To configure the switches for remote management access, create and enable interface

VLAN 43 on all three switches.

Step 3: Configure Trunking.

Note: Packet Tracer now supports the use of the range argument for

the interface command.

For interfaces FastEthernet 0/19 through FastEthernet 0/24 on all three switches:

?Configure static trunking.

?Assign VLAN 43 as the native VLAN.

Step 4: Configure VTP and VLANs.

a.Step 1: Configure SW_DS1 as VTP server and the following VTP parameters:

?SW_DS1 is the VTP server.

?VTP domain name: CCNA

?VTP password: cisco

b.Create and name the following VLANs on SW_DS1.

?VLAN 10: Student

?VLAN 20: Faculty

?VLAN 43: Management

?VLAN 67: Wireless

c.Step 2: Configure SW_AC2 and SW_AC3 as VTP clients to participate in the CCNA VTP

domain.

d.Step3: Verify that VTP is operational.

Step 5: Configure Interfaces for VLAN Access

VLAN port assignments on each switch are as follows:

a.Step 1: Configure access ports on access layer switches.

?Configure the appropriate interfaces on SW_AC2 and SW_AC3 for static access.

?Assign VLANs according to the port assignments table.

b.Step 2: Verify trunking and VLAN assignments.

Step 6: Configure Spanning Tree.

a.Modify STP root bridge elections.

?Using a priority of 4096, set SW_DS1 as the root bridge for all VLANs.

?Using a priority of 8192, set SW_AC2 as the backup root bridge for all VLANs.

b.Verify the spanning tree election.

Step 7: Configure Inter-VLAN Routing.

?Use the information in the Addressing Table to configure Router1 for inter-VLAN routing.

?Verify inter-VLAN routing.

Step 8: Configure Port Security.

Note: Best practice requires port security on all access ports. However, for this practice exercise you will only configure one port with security.

a.Configure SW_AC3 with port security on FastEthernet 0/2.

?No more than 2 MAC addresses are allowed on the FastEthernet 0/2 port for SW_AC3.

?Once learned, MAC addresses should be automatically added to the

running configuration.

?If this policy is violated, the port should be automatically disabled.

b.Verify that port security is implemented.

Step 9: Configure the Wireless LAN.

Refer to the Addressing Table to configure the wireless LAN.

a.Configure WRS.

?Use static addressing on the Internet interface.

?Set the router IP and subnet mask.

?Configure the router to allow wireless hosts to use DHCP.

?The first host address is the 10th host address in the Wireless LAN

subnet.

?The maximum number of hosts is 25.

b.Configure wireless security.

?Set the SSID to WRS_LAN.

?Enable WEP security and use 12345ABCDE as key1.

c.Enable remote management with the password cisco123.

d.Configure PC4 to access the wireless network that is provided by WRS. PC4 uses DHCP

to obtain addressing information.

Note: It will not be possible for devices to ping PC4 since PC4 is behind the WRS NAT firewall.

Step 10: Verify Connectivity.

Although these are not scored, the following connectivity tests should be successful.

?SW_DS1 can ping Router1.

?SW_AC2 can ping Router1.

?SW_AC3 can ping Router1.

?PC1 can ping PC2.

?PC2 can ping PC3.

?PC4 can ping PC1.

Version 1.0

Created in Packet Tracer 5.2.1 and Marvel 1.0.1

All contents are Copyright ? 1992 - 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

相关主题
相关文档 最新文档