当前位置:文档之家› 外文翻译1

外文翻译1

外文翻译1
外文翻译1

毕业设计(论文)

译文及原稿

译文题目:土方工程的地基勘察与施工

DESIGN AND EXECUTION OF GROUND 原稿题目:

INVESTIGATION FOR EARTHWORKS

Irish Geotechnical Services Ltd(2009)

原稿出处:

土方工程的地基勘察与施工

摘要:

当工程场地的处理面积有限且填方工程费用大量增加时,土方工程的地基勘察设计与施工已逐渐地变得重要。由于冰渍土以及含砾粘土的提出使土方工程地基勘察方法的纲要比传统的勘察方法更详细。本文提出“岩土认证”观点以及对地基勘察与土方工程相结合的优点加以概要说明。

1、引言

许多爱尔兰含砾粘土的勘察与再利用评价使岩土工程师与道路工程师感到为难。这些冰渍土或含砾粘土主要表现为低可塑性而且还含有从粘土到漂石的不同粒径颗粒。大部分本地粘土与淤泥质土中包含不同比例的砂、砾石、卵石、漂石。颗粒级配控制着土体的行为,而且淤泥使土体性质易受天气变化影响。

土体含水量随着地区不同而不同,从都柏林硬灰黑含砾粘土的7%到中部、西南部或西北部浅灰色含砾粘土沉积物的20%-25%。含砾粘土吸附水的能力建立的较好但土方工程中计划的不恰当常导致其扩大。

一般来说,良好级配的土体对于含水量的轻微变大相当敏感,将导致强度下降或不适合用作工程回填土。许多含砾粘土(尤其中等淤泥质土或良好级配的砂)在选择阶段已经被筛除,但事实上它们能对压缩或强度起到特定的作用。

筛选过程应尽量使用本地土体或者回填区或路堤边性质相对较差的土体,通过仔细评价应加以应用。回填材料必须保持一定的含水量,既不能太湿导致土体不稳定也不能太干以致不能被充分压缩。

高含水量、低强度含砾粘土适用于低路堤回填(相当于2到2.5米的高度)但不适用于没有使用土工织布隔离与回填层的土方回填工程。因此,土方工程承包商充分认识土体的处理特性相当重要,因为许多工程都受到挖掘设备通行能力的影响。

2、传统地基勘察方法

对于道路工程来讲,地基勘察最基本目标是对土体适用性进行类似表6.1的分类,该表源于国家档案登记处2000年3月版的道路施工规范。目前大部分道路施工中的地基勘察包含以下提供有关岩土参数的试验方法:

◆取样孔

◆静压法取样

◆动力探测

◆回转钻进

◆原位测试(标准贯入试验,变水头渗透试验,岩土物理试验等)

◆室内试验

评价场地工作的重要性特别是评价土体深部取样区域的适用性时不能过分强调其适用性。静压法取样通常将取样器下沉至要求深度进行取样,并每间隔一米进行取样。

在许多情况下,静压法取样由于卵石、漂石阻碍不能压入非常坚硬的含砾粘土。土样在钻孔内应尽量少扰动,但级配变坏是很正常的,级配变坏将导致土样分类不够精确。

取样孔对于恢复适当尺寸的土样以及观察碎屑岩在卵石、漂石中所占比例来说应该是适当的。因此,详尽且精确的地区描述取样区域以及取样空来说都相当重要,而且还为它们提供了检查土体在钻孔范围以外性质的良机。取样孔也提供了孔壁稳定性的评价以及观察孔壁内水进入时所造成的影响。

一位有经验的岩土工程师或工程地质专家应监督取样孔工作以及土样的恢复。因为土样性质为土样敏感性提供了信息,所以取样时土体性质应被密切关注,尤其是水从小颗粒区域迁移到良好级配区域。而且土体在开挖时的条件为其原位条件提供了一个相对精确的评价。

3、土的分类

土的描述与分类应该依照英国标准5930(1999)进行并依照英国标准1337(1990)进行测试。土的工程描述应基于按粒径大小分级并依照良好级配土的可塑性进行补充。对于许多冰渍土或含砾粘土(混合土)的难点在于其描述与工程性质测试的评价。

关于以前的地基勘察纲要,爱尔兰含砾粘土的粘土与淤泥质土中常由易变比例的砂、砾石、卵石组成。良好级配且含水量为10%-15%的低可塑性土最难进行描述与分类。现在英国标准5930(1999)已认识到描述“混合土”所存在的难点——土的良好级配较之颗粒尺寸对于控制着土的工程性质更优越。

一个关键参数在土分类以及理解过程中经常被低估,该参数就是渗透系数K。检查土的颗粒级配将间接说明土的渗透系数的大小。假如可能,为了准确评价土体的排水特性,三轴单元试验将采用无扰动原状土样或高质量土样进行试验。

低可塑性的中等渗透性含砾粘土(K大约在10-5到10-7米.秒范围内)能经常通过不同排水条件进行“模拟”。其必须在取样区域安装排水边界以及水坑边界或借用钻孔以减少土样的含水量。因此,由于含水量的小量减少,工程性质复杂的冰渍土也能当作合适的工程填土加以应用。

4、土工试验

由于室内试验的许多规定使其被建议用作土的最后试验。土的工程参数列于表 6.1,该表源于国家档案登记处2000年3月版的道路施工规范。其中包含以下内容:

◆含水量

◆颗粒级配

◆塑限

◆加州承载比

◆密实度(最优含水量)

◆重塑土不排水抗剪强度

当进行室内试验时,大量的关键因素应该被考虑。

◆密实度.加州承载比.MCV试验土样小于20mm。

◆含水量测试试样应小于20mm以提供真实有效的对比。

◆压缩时孔隙压力未加以考虑可能导致室内与实际存在相当大的差异。

◆土样测试的准备方法必须被明确规定,而且试验应在指定试验室进行。

进行含砾粘土的含水量测试时必须非常小心谨慎。理想地说,土的含水量应与其粒径有关,而且还有相应的级配分析曲线,虽然该曲线不是具有实际应用价值。

在大部分情况下,含水量被应用于密实度被认为是提供了关于建立含砾粘土适用性特征的最好方法。由于含水量能在开挖后快速评价土体的适用性,故强烈建议在取样孔中对其进行测试。因此,含水量刻度能够在实验室内不同含水量增量情况下被采用。土样扰动常发生在搬运过程中,这将对含水量的结果产生重大的影响。

地质科学研究所在进行低可塑性含砾粘土含水量测定时已经土样含水量由于时间的推移(2到7天)存在巨大的差异。许多上述低可塑性含砾粘土表现出与时间相关的含水量变化特性。其变化值主要由于土样取样时的排水条件,土样运移以及其体积的膨胀与土中水的迁移将导致土样破坏或者强度下降。

以上资料对于设计者以及土方工程承包商来说都很重要,因为进行上述规定的测试时它提供了设计者以及土方工程承包商理解土体特性的机会。它能说明在某些情况下先进行排水的所存在的优点。对于混合土来说,对土方工程进行开挖时加快排水工程非常有必要。

含砾粘土的加州承载比测试也需要非常小心谨慎,尤其是开展测试前所采用的准备工作。设计工程师必须意识到这一点,因为准备工作的误差将导致试验结果的明显不同。经验表明,采用2.5或4公斤的锤进行含砾粘土的静态击实将导致超高的孔隙压力,因此将导致加州承载比值变低。被击实含砾粘土的硬化相当重要,因为土的硬化将使孔隙水压力消散。

5、土的工程分类

依照英国标准道路施工规范,一般的粘性填土分类如表6.1如下所示:

◆2A湿粘性填土

◆2B干粘性填土

◆ 2C含石粘性填土

◆2D粉质粘性填土

首先按可接受性进行提供土样特性,然后设计工程师在实验室分类以及工程性质测试基础进行决定土工程分类的上下限。爱尔兰含砾粘土基本上都属于2C含石粘性填土。

道路施工规范612条列出了击实方法。两种现有的规程:

◆原状土样击实

◆重塑土样击实

重塑土样击实被认为最实用,特别是在土方工程合同初期阶段良好的击实控制数据可被利用。检验击实质量时,最小干密度对于合同承包商来说是最有用的。一旦土样被认可或满足工程分类要求,然后原位密度才能进行测定,当土样中含石量较低时,通常采用核子测定仪或换砂试验进行测定。

当布置或击实回填土时,原位干密度能够得到检验,不够密实的地方能够被快速识别并进行击实。该过程要求设计工程师评价击实试验区域的总体密度并估计现场真实的“理论密度”。

6、土工地基勘察方法的补充

传统的勘察方法与规程已在第二部分进行详细介绍。接下来讲述的是有助于道路工程的地基勘察工作方法的几个例子:

◆地基勘察工作分阶段进行,特别是室内测试

◆开挖&深取样孔取样

◆使用喷气或聚合物胶质体技术的大直径高质量回转钻进

◆对可能适合挖方的土样进行小范围击实试验

6.1分段勘察

对于许多大型工程来说,地基勘察工作应分阶段进行已经被提倡许多年了;特别室道路工程更应如此。因为道路工程的大量岩土工程方面数据可在短期内即可使用。大部分的大型地基勘察工程都很少花时间对最初成果进行“消化”和回顾,而且也很少对勘察方法的适用性进行重新评价。

对于土的室内测试,经常准备大量的测试计划,而在最后试验过程中这些计划并未被加以采用。在许多情况下,计划通常都是由经验少的工程师来准备,而经验丰富的工程师进行设计并未包括所准备的计划。

土的工程特性测试不但价格昂贵而且历时长(等同于加州承载比的5个点的测试&每个点的含水量测试超过两个星期)。当土的分类测试(含水量、颗粒级配分析以及阿太堡界限)完成后,才能对岩土数据以及工程特性测试计划进行进一步的分析。假如在取样期间完成了含水量的测试,那么接下来就能立刻获得土的适用性评价。

6.2深取样孔

通常都认为深取样孔的开挖既麻烦又困难,因此设计工程师们都认为该法不够恰当。采用台阶式技术以及水泵抽取地下水在含砾粘土中开挖12米深的深取样孔是可行的。

最近几年,地质科学研究所已经在好几个大型道路地基勘察工程中开挖了12米深的深取样孔。来源于这些深取样孔的宝贵数据使工程师们对土的性质有了更进一步的了解。

专家们都建议在静压法取样和回转钻进后进行深取样孔的开挖,所开挖区域的地下水状况将对深取样孔开挖的可行性起到决定作用。立管以及压力计的安装对地下水状况的了解将起到重大的帮助作用,因而这就是为何把这项工作放在地基勘察过程的后面的缘由。

大量有代表性的土样能够被获得(使用地沟箱)以及对区域抽样进行原位剪切强度测试。通过对附近取样孔的立管或压力计测试结果的比较,取样孔壁的稳定性和地下水状况可以被确定。如果取样孔深度达到惊人的500米时,三个取样孔的费用已经无法估价,还有挖出的土石需要进行小范围的击实试验。

从价值工程的观点来看,开挖以及开挖的复原的费用可以很容易计算出来,一个临时的金额被分配并用于开挖以及开挖的复原。

6.3高质量的大直径回转钻进

该系统要求使用喷气或聚合物胶质体技术的大直径回转钻进技术。用三层取心筒在超载积土层中钻进时,可循环材料被装在塑料芯衬垫中。

低可塑性含砾粘土中的岩芯萃取率相当好(典型的超过90%)。岩芯萃取率越高,那么有关工程地质的记录越详细,越有利于室内试验的试样采集。

在冰堆丘地区,例如在Cavan和Monaghan地区,地质科学研究所发现聚合物胶质体技术的大直径高质量回转钻进已经成功地在该地区非常坚硬的含砾粘土中进行深部取样(静压法取样和取样孔在该地区均失败)。原位测试(十字板,标准贯入等)能在钻孔内进行试验并获得不同地平线下强度与承载力的关系。

使用上述系统,大直径回转钻进的费用比传统的高质量钻进要高出50%到60%,但又从价值工程的角度出发,由于该法所获得的岩土信息质量相当高,所以更值得采用。

6.4小范围击实试验

在地基勘察过程中特别是主要取样剪切区域为“边界适应”土时,小范围击实试验被强烈建议采用。加上实验室数据的确认,设计者能更使土方工程的设计更贴近现实,同时为甲方单位节省相当可观的费用。

击实试验能提供以下资料:

◆场地实际密度,重塑土剪切强度以及加州承载比

◆最佳土层厚度以及碾压次数

◆击实过程中土的灵敏度(静态与动态)

◆检查车辆通行能力与车辙等级

计划场地内测试垫板的典型尺寸大致为20×10米,厚度可达1.5米。选择的场地应该在取样剪切区域或取土坑附近而且有足够的空间用来堆放材料。正常情况下,土方机械需要履带式开挖机(CAT320或其他型号),25吨运输车,D6型推土机以及牵引式或机动式碾压机。

由于核子测定仪能快速测定含水量,干密度以及容重,因此建议用该仪器测定击实回填土的原位密度测试。它能够获得一大套有关击实回填土的数据并能对击实度,土层厚度和碾压次数之间关系进行评价。扰动或未扰动击实回填土样能够进行室内测试并确认其场地测得数据(特别是含水量)。根据地质科学研究所的经验,如果计划的好,那么小范围击实试验只需两个工作日既能完成。

DESIGN AND EXECUTION OF GROUND INVESTIGATION FOR EARTHWORKS Estate PAUL

QUIGLEY, FGS

ABSTRACT

The design and execution of ground investigation works for earthwork projects has become increasingly important as the availability of suitable disposal areas becomes limited and costs of importing engineering fill increase. An outline of ground investigation methods which can augment ‘traditional investigation methods’ particularly for glacial till / boulder clay soils is presented. The issue of ‘geotechnical certification’is raised and recommendations outlined on its merits for incorporation with ground investigations and earthworks.

1.INTRODUCTION

The investigation and re-use evaluation of many Irish boulder clay soils presents difficulties for both the geotechnical engineer and the road design engineer. These glacial till or boulder clay soils are mainly of low plasticity and have particle sizes ranging from clay to boulders. Most of our boulder clay soils contain varying proportions of sand, gravel, cobbles and boulders in a clay or silt matrix. The amount of fines governs their behaviour and the silt content makes it very weather susceptible.

Moisture contents can be highly variable ranging from as low as 7% for the hard grey black Dublin boulder clay up to 20-25% for Midland, South-West and North-West light grey boulder clay deposits. The ability of boulder clay soils to take-in free water is well established and poor planning of earthworks often amplifies this.

The fine soil constituents are generally sensitive to small increases in moisture content which often lead to loss in strength and render the soils unsuitable for re-use as engineering fill. Many of our boulder clay soils (especially those with intermediate type silts and fine sand matrix) have been rejected at the selection stage, but good planning shows that they can in fact fulfil specification requirements in terms of compaction and strength.

The selection process should aim to maximise the use of locally available soils and with careful evaluation it is possible to use or incorporat e ‘poor or marginal soils’ within fill areas and embankments. Fill material needs to be placed at a moisture content such that it is neither too wet to be stable and trafficable or too dry to be properly compacted.

High moisture content / low strength boulder clay soils can be suitable for use as fill in low height embankments (i.e. 2 to 2.5m) but not suitable for trafficking by earthwork plant without using a geotextile separator and granular fill capping layer. Hence, it is vital that the earthworks contractor fully understands the handling properties of the soils, as for many projects this is effectively governed by the trafficability of earthmoving equipment.

2.TRADITIONAL GROUND INVESTIGATION METHODS

For road projects, a principal aim of the ground investigation is to classify the suitability

of the soils in accordance with Table 6.1 from Series 600 of the NRA Specification for Road Works (SRW), March 2000. The majority of current ground investigations for road works includes a combination of the following to give the required geotechnical data: ?Trial pits

?Cable percussion boreholes

?Dynamic probing

?Rotary core drilling

?In-situ testing (SPT, variable head permeability tests, geophysical etc.)

?Laboratory testing

The importance of ‘phasing’ the fieldwork op erations cannot be overstressed, particularly when assessing soil suitability from deep cut areas. Cable percussion boreholes are normally sunk to a desired depth or ‘refusal’ with disturbed and undisturbed samples recovered at 1.00m intervals or change of strata.

In many instances, cable percussion boring is unable to penetrate through very stiff, hard boulder clay soils due to cobble, boulder obstructions. Sample disturbance in boreholes should be prevented and loss of fines is common, invariably this leads to inaccurate classification.

Trial pits are considered more appropriate for recovering appropriate size samples and for observing the proportion of clasts to matrix and sizes of cobbles, boulders. Detailed and accurate field descriptions are therefore vital for cut areas and trial pits provide an opportunity to examine the soils on a larger scale than boreholes. Trial pits also provide an insight on trench stability and to observe water ingress and its effects.

A suitably experienced geotechnical engineer or engineering geologist should supervise the trial pitting works and recovery of samples. The characteristics of the soils during trial pit excavation should be closely observed as this provides information on soil sensitivity, especially if water from granular zones migrates into the fine matrix material. Very often, the condition of soil on the sides of an excavation provides a more accurate assessment of its in-situ condition.

3.SOIL CLASSIFICATION

Soil description and classification should be undertaken in accordance with BS 5930 (1999) and tested in accordance with BS 1377 (1990). The engineering description of a soil is based on its particle size grading, supplemented by plasticity for fine soils. For many of our glacial till, boulder clay soils (i.e. ‘mixed soils’) difficulties arise with descriptions and assessing engineering performance tests.

As outlined previously, Irish boulder clays usually comprise highly variable proportions of sands, gravels and cobbles in a silt or clay matrix. Low plasticity soils with fines contents of around 10 to 15% often present the most difficulties. BS 5930 (1999) now recognises these difficulties in describing ‘mixed soils’ – the fine soil constituents which govern the engineering behaviour now takes priority over particle size.

A key parameter (which is often underestimated) in classifying and understanding these soils is permeability (K). Inspection of the particle size gradings will indicate magnitude of permeability. Where possible, triaxial cell tests should be carried out on either undisturbed samples (U100’s) or good quality core samples to evaluate the drainage

characteristics of the soils accurately.

Low plasticity boulder clay soils of intermediate permeability (i.e. K of the order of 10-5 to 10-7 m/s) can o ften be ‘conditioned’ by drainage measures. This usually entails the installation of perimeter drains and sumps at cut areas or borrow pits so as to reduce the moisture content. Hence, with small reduction in moisture content, difficult glacial till soils can become suitable as engineering fill.

4. ENGINEERING PERFORMANCE TESTING OF SOILS

Laboratory testing is very much dictated by the proposed end-use for the soils. The engineering parameters set out in Table 6.1 pf the NRA SRW include a combination of the following:

?Moisture content

?Particle size grading

?Plastic Limit

?CBR

?Compaction (relating to optimum MC)

?Remoulded undrained shear strength

A number of key factors should be borne in mind when scheduling laboratory testing:

?Compaction / CBR / MCV tests are carried out on < 20mm size material.

?Moisture content values should relate to < 20mm size material to provide a valid comparison.

?Pore pressures are not taken into account during compaction and may vary considerably between laboratory and field.

?Preparation methods for soil testing must be clearly stipulated and agreed with the designated laboratory.

Great care must be taken when determining moisture content of boulder clay soils. Ideally, the moisture content should be related to the particle size and have a corresponding grading analysis for direct comparison, although this is not always practical.

In the majority of cases, the MCV when used with compaction data is considered to offer the best method of establishing (and checking) the suitability characteristics of a boulder clay soil. MCV testing during trial pitting is strongly recommended as it provides a rapid assessment of the soil suitability directly after excavation. MCV calibration can then be carried out in the laboratory at various moisture content increments. Sample disturbance can occur during transportation to the laboratory and this can have a significant impact on the resultant MCV’s.

IGSL has found large discrepancies when performing MCV’s in the field on low plasticity boulder clays with those carried out later in the laboratory (2 to 7 days). Many of the aforementioned low plasticity boulder clay soils exhibit time dependant behaviour with significantly different MCV’s recorded at a later date – increased values can be due to the drainage of the material following sampling, transportation and storage while dilatancy and migration of water from granular lenses can lead to deterioration and lower values.

This type of information is important to both the designer and earthworks contractor as it provides an opportunity to understand the properties of the soils when tested as outlined above. It can also illustrate the advantages of pre-draining in some instances. With mixed soils, face excavation may be necessary to accelerate drainage works.

CBR testing of boulder clay soils also needs careful consideration, mainly with the preparation method employed. Design engineers need to be aware of this, as it can have an order of magnitude difference in results. Static compaction of boulder clay soils is advised as compaction with the 2.5 or 4.5kg rammer often leads to high excess pore pressures being generated –hence very low CBR values can result. Also, curing of compacted boulder clay samples is important as this allows excess pore water pressures to dissipate.

5. ENGINEERING CLASSIFICATION OF SOILS

In accordance with the NRA SRW, general cohesive fill is categorised in Table 6.1 as follows:

?2A Wet cohesive

?2B Dry cohesive

?2C Stony cohesive

?2D Silty cohesive

The material properties required for acceptability are given and the design engineer then determines the upper and lower bound limits on the basis of the laboratory classification and engineering performance tests. Irish boulder clay soils are predominantly Class 2C. Clause 612 of the SRW sets out compaction methods. Two procedures are available: ?Method Compaction

?End-Product Compaction

End product compaction is considered more practical, especially when good compaction control data becomes available during the early stages of an earthworks contract. A minimum Target Dry Density (TDD) is considered very useful for the contractor to work with as a means of checking compaction quality. Once the material has been approved and meets the acceptability limits, then in-situ density can be measured, preferably by nuclear gauge or sand replacement tests where the stone content is low.

As placing and compaction of the fill progresses, the in-situ TDD can be checked and non-conforming areas quickly recognised and corrective action taken. This process requires the design engineer to review the field densities with the laboratory compaction plots and evaluate actual with ‘theoretical densities’.

6. SUPPLEMENTARY GROUND INVESTIGATION METHODS FOR EARTHWORKS

The more traditional methods and procedures have been outlined in Section 2. The following are examples of methods which are believed to enhance ground investigation works for road projects:

?Phasing the ground investigation works, particularly the laboratory testing

?Excavation & sampling in deep trial pits

?Large diameter high quality rotary core drilling using air-mist or polymer gel

techniques

Small-scale compaction trials on potentially suitable cut material

6.1PHASING

Phasing ground investigation works for many large projects has been advocated for many years –this is particularly true for road projects where significant amounts of geotechnical data becomes available over a short period. On the majority of large ground investigation projects no period is left to ‘digest’ or review the preliminary findings and re-appraise the suitability of the methods.

With regard to soil laboratory testing, large testing schedules are often prepared with no real consideration given to their end use. In many cases, the schedule is prepared by a junior engineer while the senior design engineer who will probably design the earthworks will have no real involvement.

It is highlighted that the engineering performance tests are expensive and of long duration (e.g. 5 point compaction with CBR & MCV at each point takes in excess of two weeks). When classification tests (moisture contents, particle size analysis and Atterberg Limits) are completed then a more incisive evaluation can be carried out on the data and the engineering performance tests scheduled. If MCV’s are performed during tria l pitting then a good assessment of the soil suitability can be immediately obtained.

6.2DEEP TRIAL PITS

The excavation of deep trial pits is often perceived as cumbersome and difficult and therefore not considered appropriate by design engineers. Excavation of deep trial pits in boulder clay soils to depths of up to 12m is feasible using benching techniques and sump pumping of groundwater.

In recent years, IGSL has undertaken such deep trial pits on several large road ground investigation projects. The data obtained from these has certainly enhanced the geotechnical data and provided a better understanding of the bulk properties of the soils. It is recommended that this work be carried out following completion of the cable percussion boreholes and rotary core drill holes. The groundwater regime within the cut area will play an important role in governing the feasibility of excavating deep trial pits. The installation of standpipes and piezometers will greatly assist the understanding of the groundwater conditions, hence the purpose of undertaking this work late on in the ground investigation programme.

Large representative samples can be obtained (using trench box) and in-situ shear strength measured on block samples. The stability of the pit sidewalls and groundwater conditions can also be established and compared with levels in nearby borehole standpipes or piezometers. Over a prominent cut area of say 500m, three deep trial pits can prove invaluable and the spoil material also used to carry out small-scale compaction trials.

From a value engineering perspective, the cost of excavating and reinstating these excavations can be easily recovered. A provisional sum can be allocated in the ground investigation and used for this work.

6.3HIGH QUALITY LARGE DIAMETER ROTARY CORE DRILLING

This system entails the use of large diameter rotary core drilling techniques using air mist or polymer gel flush. Triple tube core drilling is carried out through the overburden soils with the recovered material held in a plastic core liner.

Core recovery in low plasticity boulder clay has been shown to be extremely good (typically in excess of 90%). The high core recovery permits detailed engineering geological logging and provision of samples for laboratory testing.

In drumlin areas, such as those around Cavan and Monaghan, IGSL has found the use of large diameter polymer gel rotary core drilling to be very successful in recovering very stiff / hard boulder clay soils for deep road cut areas (where cable percussion boreholes and trial pits have failed to penetrate). In-situ testing (vanes, SPT’s etc) can also be carried out within the drillhole to establish strength and bearing capacity of discrete horizons.

Large diameter rotary drilling costs using the aforementioned systems are typically 50 to 60% greater than conventional HQ core size, but again from a value engineering aspect can prove much more worthwhile due to the quality of geotechnical information obtained.

6.4SMALL-SCALE COMPACTION TRIALS

The undertaking of small-scale compaction trials during the ground investigation programme is strongly advised,particularly where ‘marginally suitable’ soils are present in prominent cut areas. In addition to validating the laboratory test data, they enable more realistic planning of the earthworks and can provide considerable cost savings.

The compaction trial can provide the following:

?Achievable field density, remoulded shear strength and CBR

?Establishing optimum layer thickness and number of roller passes

?Response of soil during compaction (static v dynamic)

?Monitor trafficability & degree of rutting.

A typical size test pad would be approximately 20 x 10m in plan area and up to 1.5m in thickness. The selected area should be close to the cut area or borrow pit and have adequate room for stockpiling of material. Earthwork plant would normally entail a tracked excavator (CAT 320 or equivalent), 25t dumptruck, D6 dozer and either a towed or self-propelled roller.

In-situ density measurement on the compacted fill by nuclear gauge method is recommended as this facilitates rapid measurement of moisture contents, dry and bulk densities. It also enables a large suite of data to be generated from the compacted fill and to assess the relationship between degree of compaction, layer thickness and number of roller passes. Both disturbed and undisturbed (U100) samples of the compacted fill can be taken for laboratory testing and validation checks made with the field data (particularly moisture contents). IGSL’s experience is that with good planning a small-scale compaction trial takes two working days to complete.

外文翻译

Load and Ultimate Moment of Prestressed Concrete Action Under Overload-Cracking Load It has been shown that a variation in the external load acting on a prestressed beam results in a change in the location of the pressure line for beams in the elastic range.This is a fundamental principle of prestressed construction.In a normal prestressed beam,this shift in the location of the pressure line continues at a relatively uniform rate,as the external load is increased,to the point where cracks develop in the tension fiber.After the cracking load has been exceeded,the rate of movement in the pressure line decreases as additional load is applied,and a significant increase in the stress in the prestressing tendon and the resultant concrete force begins to take place.This change in the action of the internal moment continues until all movement of the pressure line ceases.The moment caused by loads that are applied thereafter is offset entirely by a corresponding and proportional change in the internal forces,just as in reinforced-concrete construction.This fact,that the load in the elastic range and the plastic range is carried by actions that are fundamentally different,is very significant and renders strength computations essential for all designs in order to ensure that adequate safety factors exist.This is true even though the stresses in the elastic range may conform to a recognized elastic design criterion. It should be noted that the load deflection curve is close to a straight line up to the cracking load and that the curve becomes progressively more curved as the load is increased above the cracking load.The curvature of the load-deflection curve for loads over the cracking load is due to the change in the basic internal resisting moment action that counteracts the applied loads,as described above,as well as to plastic strains that begin to take place in the steel and the concrete when stressed to high levels. In some structures it may be essential that the flexural members remain crack free even under significant overloads.This may be due to the structures’being exposed to exceptionally corrosive atmospheres during their useful life.In designing prestressed members to be used in special structures of this type,it may be necessary to compute the load that causes cracking of the tensile flange,in order to ensure that adequate safety against cracking is provided by the design.The computation of the moment that will cause cracking is also necessary to ensure compliance with some design criteria. Many tests have demonstrated that the load-deflection curves of prestressed beams are approximately linear up to and slightly in excess of the load that causes the first cracks in the tensile flange.(The linearity is a function of the rate at which the load is applied.)For this reason,normal elastic-design relationships can be used in computing the cracking load by simply determining the load that results in a net tensile stress in the tensile flange(prestress minus the effects of the applied loads)that is equal to the tensile strength of the concrete.It is customary to assume that the flexural tensile strength of the concrete is equal to the modulus of rupture of the

毕设外文资料翻译.

理工学院 毕业设计外文资料翻译 专业:计算机科学与技术 姓名:马艳丽 学号: 12L0752218 外文出处:The Design and Implementation of 3D Electronic Map of Campus Based on WEBGIS 附件: 1.外文资料翻译译文;2.外文原文。

附件1:外文资料翻译译文 基于WebGIS的校园三维电子地图的设计与实现 一.导言 如今,数字化和信息化是当今时代的主题。随着信息革命和计算机科学的发展,计算机技术已经渗透到科学的各个领域,并引起了许多革命性的变化,在这些科目,古代制图学也不例外。随着技术和文化的不断进步,地图变化的形式和内容也随之更新。在计算机图形学中,地理信息系统(GIS)不断应用到Web,制作和演示的传统方式经历了巨大的变化,由于先进的信息技术的发展,地图的应用已经大大延长。在这些情况下,绘图将面临广阔的发展前景。电子地图是随之应运而生的产品之一。随着计算机技术,计算机图形学理论,遥感技术,航空摄影测量技术和其他相关技术的飞速发展。用户需要的三维可视化,动态的交互性和展示自己的各种地理相关的数据处理和分析,如此多的关注应支付的研究三维地图。东北石油大学及其周边地区的基础上本文设计并建立三维电子地图。 二.系统设计 基于WebGIS的校园三维电子地图系统的具有普通地图的一般特性。通过按键盘上的箭头键(上,下,左,右),可以使地图向相应的方向移动。通过拖动鼠标,可以查看感兴趣的任何一个地方。使用鼠标滚轮,可以控制地图的大小,根据用户的需求来查看不同缩放级别的地图。在地图的左下角会显示当前鼠标的坐标。在一个div层,我们描绘了一个新建筑物的热点,这层可以根据不同的地图图层的显示,它也可以自动调整。通过点击热点,它可以显示热点的具体信息。也可以输入到查询的信息,根据自己的需要,并得到一些相关的信息。此外,通过点击鼠标,人们可以选择检查的三维地图和卫星地图。 主要功能包括: ?用户信息管理:检查用户名和密码,根据权限设置级别的认证,允许不同权限的用户通过互联网登录系统。 ?位置信息查询:系统可以为用户提供模糊查询和快速定位。

网络营销外文翻译

E---MARKETING (From:E--Marketing by Judy Strauss,Adel El--Ansary,Raymond Frost---3rd ed.1999 by Pearson Education pp .G4-G25.) As the growth of https://www.doczj.com/doc/1011233101.html, shows, some marketing principles never change.Markets always welcome an innovative new product, even in a crowded field of competitors ,as long as it provides customer value.Also,Google`s success shows that customers trust good brands and that well-crafted marketing mix strategies can be effective in helping newcomers enter crowded markets. Nevertheless, organizations are scrambling to determine how they can use information technology profitably and to understand what technology means for their business strategies. Marketers want to know which of their time-ested concepts will be enhanced by the Internet, databases,wireless mobile devices, and other technologies. The rapid growth of the Internet and subsequent bursting of the dot-com bubble has marketers wondering,"What next?" This article attempts to answer these questions through careful and systematic examination of successful e-mar-keting strategies in light of proven traditional marketing practices. (Sales Promotion;E--Marketing;Internet;Strategic Planning ) 1.What is E--Marketing E--Marketing is the application of a broad range of information technologies for: Transforming marketing strategies to create more customer value through more effective segmentation ,and positioning strategies;More efficiently planning and executing the conception, distribution promotion,and pricing of goods,services,and ideas;andCreating exchanges that satisfy individual consumer and organizational customers` objectives. This definition sounds a lot like the definition of traditional marketing. Another way to view it is that e-marketing is the result of information technology applied to traditional marketing. E-marketing affects traditional marketing in two ways. First,it increases efficiency in traditional marketing strategies.The transformation results in new business models that add customer value and/or increase company profitability.

毕业设计外文翻译资料

外文出处: 《Exploiting Software How to Break Code》By Greg Hoglund, Gary McGraw Publisher : Addison Wesley Pub Date : February 17, 2004 ISBN : 0-201-78695-8 译文标题: JDBC接口技术 译文: JDBC是一种可用于执行SQL语句的JavaAPI(ApplicationProgrammingInterface应用程序设计接口)。它由一些Java语言编写的类和界面组成。JDBC为数据库应用开发人员、数据库前台工具开发人员提供了一种标准的应用程序设计接口,使开发人员可以用纯Java语言编写完整的数据库应用程序。 一、ODBC到JDBC的发展历程 说到JDBC,很容易让人联想到另一个十分熟悉的字眼“ODBC”。它们之间有没有联系呢?如果有,那么它们之间又是怎样的关系呢? ODBC是OpenDatabaseConnectivity的英文简写。它是一种用来在相关或不相关的数据库管理系统(DBMS)中存取数据的,用C语言实现的,标准应用程序数据接口。通过ODBCAPI,应用程序可以存取保存在多种不同数据库管理系统(DBMS)中的数据,而不论每个DBMS使用了何种数据存储格式和编程接口。 1.ODBC的结构模型 ODBC的结构包括四个主要部分:应用程序接口、驱动器管理器、数据库驱动器和数据源。应用程序接口:屏蔽不同的ODBC数据库驱动器之间函数调用的差别,为用户提供统一的SQL编程接口。 驱动器管理器:为应用程序装载数据库驱动器。 数据库驱动器:实现ODBC的函数调用,提供对特定数据源的SQL请求。如果需要,数据库驱动器将修改应用程序的请求,使得请求符合相关的DBMS所支持的文法。 数据源:由用户想要存取的数据以及与它相关的操作系统、DBMS和用于访问DBMS的网络平台组成。 虽然ODBC驱动器管理器的主要目的是加载数据库驱动器,以便ODBC函数调用,但是数据库驱动器本身也执行ODBC函数调用,并与数据库相互配合。因此当应用系统发出调用与数据源进行连接时,数据库驱动器能管理通信协议。当建立起与数据源的连接时,数据库驱动器便能处理应用系统向DBMS发出的请求,对分析或发自数据源的设计进行必要的翻译,并将结果返回给应用系统。 2.JDBC的诞生 自从Java语言于1995年5月正式公布以来,Java风靡全球。出现大量的用java语言编写的程序,其中也包括数据库应用程序。由于没有一个Java语言的API,编程人员不得不在Java程序中加入C语言的ODBC函数调用。这就使很多Java的优秀特性无法充分发挥,比如平台无关性、面向对象特性等。随着越来越多的编程人员对Java语言的日益喜爱,越来越多的公司在Java程序开发上投入的精力日益增加,对java语言接口的访问数据库的API 的要求越来越强烈。也由于ODBC的有其不足之处,比如它并不容易使用,没有面向对象的特性等等,SUN公司决定开发一Java语言为接口的数据库应用程序开发接口。在JDK1.x 版本中,JDBC只是一个可选部件,到了JDK1.1公布时,SQL类包(也就是JDBCAPI)

1外文文献翻译原文及译文汇总

华北电力大学科技学院 毕业设计(论文)附件 外文文献翻译 学号:121912020115姓名:彭钰钊 所在系别:动力工程系专业班级:测控技术与仪器12K1指导教师:李冰 原文标题:Infrared Remote Control System Abstract 2016 年 4 月 19 日

红外遥控系统 摘要 红外数据通信技术是目前在世界范围内被广泛使用的一种无线连接技术,被众多的硬件和软件平台所支持。红外收发器产品具有成本低,小型化,传输速率快,点对点安全传输,不受电磁干扰等特点,可以实现信息在不同产品之间快速、方便、安全地交换与传送,在短距离无线传输方面拥有十分明显的优势。红外遥控收发系统的设计在具有很高的实用价值,目前红外收发器产品在可携式产品中的应用潜力很大。全世界约有1亿5千万台设备采用红外技术,在电子产品和工业设备、医疗设备等领域广泛使用。绝大多数笔记本电脑和手机都配置红外收发器接口。随着红外数据传输技术更加成熟、成本下降,红外收发器在短距离通讯领域必将得到更广泛的应用。 本系统的设计目的是用红外线作为传输媒质来传输用户的操作信息并由接收电路解调出原始信号,主要用到编码芯片和解码芯片对信号进行调制与解调,其中编码芯片用的是台湾生产的PT2262,解码芯片是PT2272。主要工作原理是:利用编码键盘可以为PT2262提供的输入信息,PT2262对输入的信息进行编码并加载到38KHZ的载波上并调制红外发射二极管并辐射到空间,然后再由接收系统接收到发射的信号并解调出原始信息,由PT2272对原信号进行解码以驱动相应的电路完成用户的操作要求。 关键字:红外线;编码;解码;LM386;红外收发器。 1 绪论

外文翻译

Journal of Industrial Textiles https://www.doczj.com/doc/1011233101.html,/ Optimization of Parameters for the Production of Needlepunched Nonwoven Geotextiles Amit Rawal, Subhash Anand and Tahir Shah 2008 37: 341Journal of Industrial Textiles DOI: 10.1177/1528083707081594 The online version of this article can be found at: https://www.doczj.com/doc/1011233101.html,/content/37/4/341 Published by: https://www.doczj.com/doc/1011233101.html, can be found at:Journal of Industrial TextilesAdditional services and information for https://www.doczj.com/doc/1011233101.html,/cgi/alertsEmail Alerts: https://www.doczj.com/doc/1011233101.html,/subscriptionsSubscriptions: https://www.doczj.com/doc/1011233101.html,/journalsReprints.navReprints: https://www.doczj.com/doc/1011233101.html,/journalsPermissions.navPermissions: https://www.doczj.com/doc/1011233101.html,/content/37/4/341.refs.htmlCitations: - Mar 28, 2008Version of Record >>

毕业设计外文翻译附原文

外文翻译 专业机械设计制造及其自动化学生姓名刘链柱 班级机制111 学号1110101102 指导教师葛友华

外文资料名称: Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处:Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件: 1.外文资料翻译译文 2.外文原文

应用旋风技术真空吸尘器的设计和性能介绍 吉尔泰金,洪城铱昌,宰瑾李, 刘链柱译 摘要:旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率,压降,并切成尺寸被粒度对应于分级收集的50%的效率进行了研究。颗粒切成大小降低入口面积,体直径,减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法,用于收集在家庭中产生的粉尘。 摘要及关键词:吸尘器; 粉尘; 旋风分离器 引言 我们这个时代的很大一部分都花在了房子,工作场所,或其他建筑,因此,室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物,毒物,食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤,预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中,吸入压力下降说唱空转成比例地清洗的时间,以及纸过滤器也应定期更换,由于压力下降,气味和细菌通过纸过滤器内的残留粉尘。 图1示出了大气气溶胶的粒度分布通常是双峰形,在粗颗粒(>2.0微米)模式为主要的外部来源,如风吹尘,海盐喷雾,火山,从工厂直接排放和车辆废气排放,以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式,典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克,可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。

外文翻译中文版(完整版)

毕业论文外文文献翻译 毕业设计(论文)题目关于企业内部环境绩效审计的研究翻译题目最高审计机关的环境审计活动 学院会计学院 专业会计学 姓名张军芳 班级09020615 学号09027927 指导教师何瑞雄

最高审计机关的环境审计活动 1最高审计机关越来越多的活跃在环境审计领域。特别是1993-1996年期间,工作组已检测到环境审计活动坚定的数量增长。首先,越来越多的最高审计机关已经活跃在这个领域。其次是积极的最高审计机关,甚至变得更加活跃:他们分配较大部分的审计资源给这类工作,同时出版更多环保审计报告。表1显示了平均数字。然而,这里是机构间差异较大。例如,环境报告的数量变化,每个审计机关从1到36份报告不等。 1996-1999年期间,结果是不那么容易诠释。第一,活跃在环境审计领域的最高审计机关数量并没有太大变化。“活性基团”的组成没有保持相同的:一些最高审计机关进入,而其他最高审计机关离开了团队。环境审计花费的时间量略有增加。二,但是,审计报告数量略有下降,1996年和1999年之间。这些数字可能反映了从量到质的转变。这个信号解释了在过去三年从规律性审计到绩效审计的转变(1994-1996年,20%的规律性审计和44%绩效审计;1997-1999:16%规律性审计和绩效审计54%)。在一般情况下,绩效审计需要更多的资源。我们必须认识到审计的范围可能急剧变化。在将来,再将来开发一些其他方式去测算人们工作量而不是计算通过花费的时间和发表的报告会是很有趣的。 在2000年,有62个响应了最高审计机关并向工作组提供了更详细的关于他们自1997年以来公布的工作信息。在1997-1999年,这62个最高审计机关公布的560个环境审计报告。当然,这些报告反映了一个庞大的身躯,可用于其他机构的经验。环境审计报告的参考书目可在网站上的最高审计机关国际组织的工作组看到。这里这个信息是用来给最高审计机关的审计工作的内容更多一些洞察。 自1997年以来,少数环境审计是规律性审计(560篇报告中有87篇,占16%)。大多数审计绩效审计(560篇报告中有304篇,占54%),或组合的规律性和绩效审计(560篇报告中有169篇,占30%)。如前文所述,绩效审计是一个广泛的概念。在实践中,绩效审计往往集中于环保计划的实施(560篇报告中有264篇,占47%),符合国家环保法律,法规的,由政府部门,部委和/或其他机构的任务给访问(560篇报告中有212篇,占38%)。此外,审计经常被列入政府的环境管理系统(560篇报告中有156篇,占28%)。下面的元素得到了关注审计报告:影响或影响现有的国家环境计划非环保项目对环境的影响;环境政策;由政府遵守国际义务和承诺的10%至20%。许多绩效审计包括以上提到的要素之一。 1本文译自:S. Van Leeuwen.(2004).’’Developments in Environmental Auditing by Supreme Audit Institutions’’ Environmental Management Vol. 33, No. 2, pp. 163–1721

毕业设计外文翻译

毕业设计(论文) 外文翻译 题目西安市水源工程中的 水电站设计 专业水利水电工程 班级 学生 指导教师 2016年

研究钢弧形闸门的动态稳定性 牛志国 河海大学水利水电工程学院,中国南京,邮编210098 nzg_197901@https://www.doczj.com/doc/1011233101.html,,niuzhiguo@https://www.doczj.com/doc/1011233101.html, 李同春 河海大学水利水电工程学院,中国南京,邮编210098 ltchhu@https://www.doczj.com/doc/1011233101.html, 摘要 由于钢弧形闸门的结构特征和弹力,调查对参数共振的弧形闸门的臂一直是研究领域的热点话题弧形弧形闸门的动力稳定性。在这个论文中,简化空间框架作为分析模型,根据弹性体薄壁结构的扰动方程和梁单元模型和薄壁结构的梁单元模型,动态不稳定区域的弧形闸门可以通过有限元的方法,应用有限元的方法计算动态不稳定性的主要区域的弧形弧形闸门工作。此外,结合物理和数值模型,对识别新方法的参数共振钢弧形闸门提出了调查,本文不仅是重要的改进弧形闸门的参数振动的计算方法,但也为进一步研究弧形弧形闸门结构的动态稳定性打下了坚实的基础。 简介 低举升力,没有门槽,好流型,和操作方便等优点,使钢弧形闸门已经广泛应用于水工建筑物。弧形闸门的结构特点是液压完全作用于弧形闸门,通过门叶和主大梁,所以弧形闸门臂是主要的组件确保弧形闸门安全操作。如果周期性轴向载荷作用于手臂,手臂的不稳定是在一定条件下可能发生。调查指出:在弧形闸门的20次事故中,除了极特殊的破坏情况下,弧形闸门的破坏的原因是弧形闸门臂的不稳定;此外,明显的动态作用下发生破坏。例如:张山闸,位于中国的江苏省,包括36个弧形闸门。当一个弧形闸门打开放水时,门被破坏了,而其他弧形闸门则关闭,受到静态静水压力仍然是一样的,很明显,一个动态的加载是造成的弧形闸门破坏一个主要因素。因此弧形闸门臂的动态不稳定是造成弧形闸门(特别是低水头的弧形闸门)破坏的主要原是毫无疑问。

营销-外文翻译

外文翻译 原文 Marketing Material Source:Marketing Management Author:Philip Kotler Marketing Channels To reach a target market, the marketer uses three kinds of marketing channels. Communication channels deliver messages to and receive messages from target buyers. They include newspapers, magazines, radio, television, mail, telephone, billboards, posters, fliers, CDs, audiotapes, and the Internet. Beyond these, communications are conveyed by facial expressions and clothing, the look of retail stores, and many other media. Marketers are increasingly adding dialogue channels (e-mail and toll-free numbers) to counterbalance the more normal monologue channels (such as ads). The marketer uses distribution channels to display or deliver the physical product or service to the buyer or user. There are physical distribution channels and service distribution channels, which include warehouses, transportation vehicles, and various trade channels such as distributors, wholesalers, and retailers. The marketer also uses selling channels to effect transactions with potential buyers. Selling channels include not only the distributors and retailers but also the banks and insurance companies that facilitate transactions. Marketers clearly face a design problem in choosing the best mix of communication, distribution, and selling channels for their offerings. Supply Chain Whereas marketing channels connect the marketer to the target buyers, the supply chain describes a longer channel stretching from raw materials to components to final products that are carried to final buyers. For example, the supply chain for women’s purses starts with hides, tanning operations, cutting operations, manufacturing, and the marketing channels that bring products to customers. This supply chain represents a value delivery system. Each company captures only a certain percentage of the total value generated by the supply chain. When a company acquires competitors or moves upstream or downstream, its aim is

外文翻译

华南理工大学广州学院 本科毕业设计(论文)外文翻译 外文原文名Marketing Strategy Adjustment and Marketing Innovation in the Experience Economy Era 中文译名体验经济时代的营销战略调整与营销创新 学院管理学院 专业班级2013级工商管理1班 学生姓名潘嘉谊 学生学号201330090184 指导教师罗玲苑讲师李巍巍 填写日期2017年5月19日

外文原文版出处:.Marketing Strategy Adjustment and Marketing Innovation in the Experience Economy Era[J]. Contemporary Logistics,2012 (06) :230-267 译文成绩:指导教师(导师组长)签名: 译文: 体验经济时代的营销战略调整与营销创新 吴青学 摘要:从商品货物经济,到服务经济的的转移演化经历过程,经历了农业经济、工业经济,服务经济和体验经济。在服务经济时期,企业只是打包经验与传统的产品一起销售,而在促进经验经济的时期,企业要把最好产品为未来的潜在用户设计,让消费者心甘情愿支付购买产品。 关键词:体验经济;市场营销战略;营销创新 1 介绍 随着科学技术和信息行业的发展,人们的需要和欲望连同消费者支出模式开始发生转变,相应地对企业生产环境产生了一系列影响。经济社会发展由传统时期进入体验经济时期。从一个经济产品的转变,进而到经济体系经济模式的转变。由缓慢转变为激进经济模式。因此导致社会发展从一个经济时期到另一个经济时期,经济模式和经济体系的转变将不可避免地影响到交换关系的转化。这是关注体验的结果,是由人类社会的发展的规律所决定的生产水平的产物。一旦交流关系发生变化、营销模式必须做出相应的变化。 2 企业营销策略的选择方向 在体验经济时代,企业不仅要理性思考高瞻远瞩,从客户的角度实施营销活动,更要重视与沟通客户,发现在他们内心的期望。我们自己的产品和服务代表企业的形象,产品要指向指定的客户体验。在当今时代,体验营销已成为营销活动最强大的秘密武器因此,这是非常重要的。而传统的营销策略,包括调整经验营销都已经不适应当前发展需求,迟早要被时代所淘汰。 2.1 建立营销思想的观念要求提高客户体验 根据马斯洛需求层次理论,人的需要分为五个层次,分别是:生理的需要、安全的需要、归属于爱的需要、尊重的需要和自我实现的需要。随着经济的发展和消费者日益增强的购买能力变化,人们生理需求得到满足,个人需求将会上升心

毕设外文文献翻译

xxxxxxxxx 毕业设计(论文)外文文献翻译 (本科学生用) 题目:Poduct Line Engineering: The State of the Practice 生产线工程:实践的形态 学生姓名:学号: 学部(系): 专业年级: 指导教师:职称或学位: 2011年3月10日

外文文献翻译(译成中文1000字左右): 【主要阅读文献不少于5篇,译文后附注文献信息,包括:作者、书名(或论文题目)、出版社(或刊物名称)、出版时间(或刊号)、页码。提供所译外文资料附件(印刷类含封面、封底、目录、翻译部分的复印件等,网站类的请附网址及原文】 Requirements engineering practices A precise requirements engineering process— a main driver for successful software development —is even more important for product line engineering. Usually, the product line’s scope addresses various domains simultaneously. This makes requirements engineering more complex. Furthermore, SPL development involves more tasks than single-product development. Many product line requirements are complex, interlinked, and divided into common and product-specific requirements. So, several requirements engineering practices are important specifically in SPL development: ? Domain identification and modeling, as well as commonalities and variations across product instances Separate specification and verification for platform and product requirements ? Management of integrating future requirements into the platform and products ? Identification, modeling, and management of requirement dependencies The first two practices are specific to SPL engineering. The latter two are common to software development but have much higher importance for SPLs. Issues with performing these additional activities can severely affect the product line’s long-term success. During the investigation, we found that most organizations today apply organizational and procedural measures to master these challenges. The applicability of more formal requirements engineering techniques and tools appeared rather limited, partly because such techniques are not yet designed to cope with product line evelopment’s inherent complexities. The investigation determined that the following three SPL requirements engineering practices were most important to SPL success. Domain analysis and domain description. Before starting SPL development, organizations should perform a thorough domain analysis. A well-understood domain is a prerequisite for defining a suitable scope for the product line. It’s the foundation for efficiently identifying and distinguishing platform and product requirements. Among the five participants in our investigation, three explicitly modeled the product line requirements. The others used experienced architects and domain experts to develop the SPL core assets without extensive requirements elicitation. Two organizations from the first group established a continuous requirements management that maintained links between product line and product instance requirements. The three other organizations managed their core assets’ evolution using change management procedures and versioning concepts. Their business did not force them to maintain more detailed links between the requirements on core assets and product instances. The impact of architectural decisions on requirements negotiations. A stable but flexible architecture is important for SPL development. However, focusing SPL evolution too much on architectural issues will lead to shallow or even incorrect specifications. It can cause core assets to ignore important SPL requirements so that the core assets lose relevance for SPL development. Organizations can avoid this problem by establishing clear responsibilities for requirements management in addition to architectural roles. The work group participants reported that a suitable organizational tool for balancing requirements and architecture is roundtable meetings in which requirements engineers,

相关主题
相关文档 最新文档