当前位置:文档之家› 焊接专业术语中英文对照整理

焊接专业术语中英文对照整理

焊接专业术语中英文对照整理
焊接专业术语中英文对照整理

机械——焊接专业术语中英文对照

(郭运)整理

1Single 单面的

2V—groove V型坡口

3Joint 焊接接头

4Edges overlap 接头形式

5Butt 对接

6T T型焊接

7Fillet 角焊缝

8Edge 端接

9Corner 角接

10Radius 半径

11Joint root 焊接根部

12Bevel angle 削边角度

13Groove angle 坡口角度

14Root face 根部钝边

15Groove face 坡口面

16Plug weld 塞焊

17Spot weld 点焊

18Seam weld 缝焊

19Slot weld 槽焊

20Double—flare—bevel—groove K型坡口焊缝

21Single—flare—V 单面V型22Edge flange 翻边端接

23Corner flange 卷边端接

24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝

27Slot weld 槽焊缝

28Spot weld 点焊缝

29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚

40Toe 焊趾

41Buildup 堆焊

42Weld reinforcement 焊缝加强高

43Effective throat 有效焊喉

44Concave weld 凹形焊缝

45Convex weld 凸形焊缝

46Unequal leg fillet 不等脚角焊

47Oversize weld 大尺寸焊缝

48Depth of fusion 熔合深度

49Depth of penetration 熔透深度

50Root penetration 根部熔深

51Joint penetration 接头熔深

52Weld interface 焊缝分界面

53Diameter of weld at point of contact 焊缝在接触点上的直径

54Thickness 厚度

55Tail 尾部

56Arrow 箭头

57Reference line 参考线

58Arrow side 箭头一边

59Weld symbol 焊缝符号

60Near side 近侧

61Arrow side 箭头侧

62Far side 远侧

63Other side 另一侧

64Put the weld on either—side 在任意一侧施焊65There is no side significance 没有方向区别66Edge flange 双卷边

67Corner flange 单卷边

68Weld size 焊缝尺寸

69Effective throat 有效厚度

70Root opening 根部间隙

71Full penetration double bevel—groove weld K形坡口全焊透焊缝

72Full penetration double V—groove weld 双V形坡口全焊透焊缝

73Partial penetration double bevel—groove weld K形坡口部分焊透焊缝

74Partial penetration double V—groove weld 双V形坡口部分焊透焊缝

75Bevel groove 削边坡口

76Flare groove 喇叭形坡口77Flange groove 卷边坡口

78V—groove V形坡口

79Staggered intermittent fillet weld 交错间断角焊缝

80Chain intermittent fillet weld 链状间断角

焊缝

81Segmented fillet weld 分段角焊缝82Pitch distance 间距

83Depth of filling 填充深度

84Slot weld width 槽焊缝宽度85Plug weld diameter 塞焊缝的直径86Angle of countersink 深孔角度

87A dimension to the right of the symbol 在符号右边的尺寸

88A dimension of the required suggest diameter 所要求的直径尺寸

89A value for the required shear strength per spot 每点所要求的剪切强度值

90Spot weld size 点焊缝尺寸91Spot weld length 点焊缝的长度

92Number of spot required 所要求的点的数量

93Pitch distance between adjacent spots 两个相邻点的间距

94Reference line 参考线

95Melt—through of weld from other side 焊缝在另一

侧熔透

96Single bevel—groove weld with backing weld 加垫板的单边坡口焊缝

97Single bevel—groove weld with back weld 背面焊的单边坡口焊缝

98Single bevel—groove weld with backing weld 带垫板的V 形坡口焊缝

99Single bevel—groove weld with back weld背面焊的V形坡口焊缝

100Square groove 直边坡口

101Skewed groove 斜坡口

102Sloped groove 倾斜坡口

103Scarf 斜嵌接

104Gas metal arc spot weld 气体保护点焊105Resistance spot weld 电阻点焊

106Gas metal arc seam weld 气体保护滚焊缝107Resistance seam weld 电阻滚焊缝

108Gas metal arc slot weld 气体保护槽焊缝109The type of electrode to use 所要求焊条形式110The weld quality standard 焊缝质量标准111The weld procedure to use 所用的焊接程序112Codes 规范

113Drawing 图纸

114Specifications 技术要求

115Contracts 合同

116General 一般注解

117Local 局部注解

118The point for lifting an object 吊装一物体的点119Filler metals 填充金属

120Pressure vessel fabrication 压力容器制造121Be as simple as possible 尽可能简单

122Welder 焊工

123Code body 规范本身

124Shielded metal arc 手工电弧焊125Submerged arc 埋弧焊

126Face bend 面弯

127Root bend 背弯

128Side bend 侧弯

129Nick break 缺口破坏

130Tensile 拉伸

131Monitoring production welding 监视生产中的焊接

132Strength 强度

133Toughness 韧性

134Hardness 硬度

135Ductility 延展性

136Compressive 压缩

137Impact 冲击

138Fatigue 疲劳

139Undercut 咬边

140Overlap 焊瘤

141Cracking 裂纹

142Porosity 气孔

143Ultimate tensile strength 极限拉伸强度144Percent elongation 延伸率

145Percent reduction of area 断面收缩率146Impact strength 冲击强度147Yield strength 屈服强度148Brinell 布氏

149Vickers 韦氏

150Rockwell 洛氏

151Knoop 努氏

152Fatigue test 疲劳试验153Tensile test 拉伸试验154Micro--hardness test 显微硬度试验155Charpy impact test 夏比冲击试验

156Soundness test 致密性测试

157Fillet break 角焊缝断裂

158Metallographic 金相

159Transverse fillet weld shear test 横向角焊缝剪切试验

160Quality of the fractured weld 焊缝端口的质量161Ductility of the weld metal 焊缝金属的延展性162Impact strength of the weld 焊缝的冲击强度163Tensile strength of the base metal 母材的拉伸强度164Weld—ability 可焊性

165Scratches caused by improper handling 由不适当的处理导致的划痕

166Incomplete fusion 未熔合

167Distortion 变形

168Slag inclusions 夹渣

169Vibratory stress relief 振动消除应力

170External restraint 外部拘束

171Thermal stress relief 热消除应力

172Peening 锤击

173Annealing 退火

174Quenching 淬火

175Tempering 回火

176Normalizing 正火

177Decrease current 降低电流

178Decrease voltage 降低电压

179Increase travel speed 加快焊接速度

180Change from weave to stringer bead technique 从横向摆动焊道改成直线焊道技术

181Result in a wider heat—affected zone hardness导致热影响区更宽

182Produce a lower heat—affected zone hardness 降低热影响区硬度

183Slow down the cooling rate 降低冷却速度184Reduce the tendency to produce martensite in the heat—affected zone 减少在热影响区形成马氏体的倾向

185Stress relief 消除应力

186Crater crack 弧坑裂纹

187SMAW 手动电弧焊

188PAW 等离子焊

189FCAW 药芯焊

190SAW 埋弧焊

191Underfill 未焊满

192Excess convexity 太凸

193Excess weld reinforcement 焊缝余高太高194Overfill 过充

195Scratch start 擦伤

196Arc strike 引弧烧伤197Tungsten inclusion 夹钨

198Lamination 分层

199Lamellar tear 片状撕裂200Seam 划伤

201Pipe shrinkage 缩孔

202Longitudinal crack 纵向裂纹203Transverse crack 横向裂纹204Underbead crack 焊道中裂纹205Toe crack 焊趾裂纹206Root crack 根部裂纹207Base metal crack 母材裂纹208Before welding 焊接前

209During welding 焊接时

210After welding 焊接后

211Waiting time 等待时间212Penetrating time 渗透时间213Soak time 吸入时间214Dwell time 驻留时间

215AC 交流电216DC 直流电217DCEP 直流反接218

财务专业术语中英文对照表

财务专业术语中英文对照表 英文中文说明 Account Accounting system 会计系统 American Accounting Association 美国会计协会 American Institute of CPAs 美国注册会计师协会 Audit 审计 Balance sheet 资产负债表 Bookkeepking 簿记 Cash flow prospects 现金流量预测 Certificate in Internal Auditing 部审计证书 Certificate in Management Accounting 管理会计证书 Certificate Public Accountant注册会计师 Cost accounting 成本会计 External users 外部使用者 Financial accounting 财务会计 Financial Accounting Standards Board 财务会计准则委员会 Financial forecast 财务预测 Generally accepted accounting principles 公认会计原则 General-purpose information 通用目的信息 Government Accounting Office 政府会计办公室 Income statement 损益表 Institute of Internal Auditors 部审计师协会 Institute of Management Accountants 管理会计师协会 Integrity 整合性 Internal auditing 部审计 Internal control structure 部控制结构 Internal Revenue Service 国收入署 Internal users部使用者 Management accounting 管理会计 Return of investment 投资回报 Return on investment 投资报酬 Securities and Exchange Commission 证券交易委员会

音响专业术语中英对照

专业音频术语中英文对照 A AAC automatic ampltiude control 自动幅度控制 AB AB制立体声录音法?Abeyancd 暂停,潜态 A-B repeat A-B重复?ABS absolute 绝对得,完全得,绝对时间 ABSamerican bureau ofstanda rd 美国标准局?ABSS autoblank secrion scanning 自动磁带空白部分扫描Absti me绝对运行时间?A、DEF audio defeat音频降噪,噪声抑制,伴音静噪 ADJ adj ective 附属得,附件?ADJ Adjust 调节 ADJ acousticdelay line声延迟线 Admission 允许进入,供给 ADP acousticdata processor音响数据处理机 ADP(T) adapter 延配器,转接器ADRES automaticdynamic range expansion system?动态范围扩展系统 A DRM analog todigital remaster 模拟录音、数字处理数码唱盘 ADS audio distribution system 音频分配系统 A、DUB audio dubbing配音,音频复制,后期录音 ADV advance 送入,提升,前置量?ADV adversum对抗 ADV advance r 相位超前补偿器?Adventure惊险效果 AE audio erasing 音频(声音)擦除 AE auxiliary equipment 辅助设备Aerial天线 AESaudio engineering society美国声频工程协会AF audio fidelity 音频保真度?AF audio frequency音频频率 AFC active field control自动频率控制?AFC automaticfrequency control 声场控制 Affricate 塞擦音?AFL aside fade listen 衰减后(推子后)监听 A-fader 音频衰减 AFM advance frequency modulation 高级调频 AFS acoustic feedback spea ker 声反馈扬声器 AFT automatic fine tuning 自动微调 AFTAAS advancedfast time acousti canalysis system?高级快速音响分析系统 After 转移部分文件 Afterglow余辉,夕照时分音响效果 Again st 以……为背景 AGC automatic gain control 自动增益控制AHDaudiohigh density音频高密度唱片系统 AI advanced integrated预汇流AI amplifier input 放大器输入 AI artificial intelligence 人工智能AI azimuth indi cator 方位指示器 A-IN 音频输入 A-INSEL audio input selection 音频输入选择 Alarm 警报器 ALC automatic level control自动电平控制?ALC automatic load control自动负载控制

SMT焊接不良现象中英文对照表

[replyview]不良现象中英文对照表 1.缺件(MISSING PARTS) 28.脚未弯(PIN NOT BENT) 55.印章错误(WRONG STAMPS) 2.错件(WRONG PARTS) 29.缺盖章(MISSING STAMP) 56.尺寸错误 (DIMENSION WRONG) 3.多件(EXCESSIVE PARTS) 30.缺卷标(MISSING LABEL) 57.二极管坏 (DIODE NG) 4.短路(SHORT) 31.缺序号(MISSING S/N) 58.晶体管坏(TRANSISTOR NG) 5.断路(OPEN) 32.序号错(WRONG S/N) 59.振荡器坏(X’TL NG) 6.线短(WIRE SHORT) 33.卷标错(WRONG LABEL) 60.管装错误(TUBES WRONG) 7.线长(WIRE LONG) 34.标示错(WRONG MARK) 61.阻值错误(IMPEDANCE WRONG) 8.拐线(WIRE POOR DDRESS) 35.脚太短(PIN SHORT) 62.版本错误(REV WRONG) 9.冷焊(COLD SOLDER) 36.J1不洁(J1 DIRTY) 63.电测不良(TEST FAILURE) 10.包焊(EXCESS SOLDER) 37.锡凹陷(SOLDER SCOOPED) 64.版本未标(NON REV LEBEL) 11.空焊(MISSING SOLDER) 38.线序错(W/L OF WIRE) 65.包装损坏 (PACKING DAMAGED) 12.锡尖(SOLDER ICICLE) 39.未测试(NO TEST) 66.印章模糊(STAMPS DEFECTIVE) 13.锡渣(SOLDER SPLASH) 40.VR变形(VR DEFORMED) 67.卷标歪斜(LABEL TILT) 14.锡裂(SODER CRACK) 41.PCB翘皮(PCB PEELING) 68.外箱损坏(CARTON DAMAGED) 15.锡洞(PIN HOLE) 42.PCB弯曲(PCB TWIST) 69.点胶不良(POOR GLUE) 16.锡球(SOLDER BALL) 43.零件沾胶(GLUE ON PARTS) 70.IC座氧化 (SOCKET RUST)

(完整版)放疗专业术语中英文对照表

Chemntherapeutic agents 化学疗法 thus xue fiao fa) Chemothcrjipy 化学疔,Z (hija xue Aaa fa) hns the goal of killing or stopping rhe development nf rapidly dividing cells. Examples are Cisplatin, Carboplat in, Bkomycin I 博来霉嗪1 (ftd l3f Sg S-fltinrncjrao 5 氟尿瞪喘(ft/ HiAO m dfinfl), mrthotrExate 甲員媒时{Jia 的 did /ioffk Vincristine fifr chun xJTj/a^, Vinblastine 衣祚碱 (chang chun ;ian}. Taxol and Tawiuvirtn .木戟题(SSfi ben 阳ng 钠* Since the sanK nicchanism (hat kilh malignant cdl or blocks de vela pment of a malignant cell cm have similar effects on a nnrnuil, rap idly dividing celt any of LhcNt agents ciin hax r c btid side clfccts. Some terms of cancer ircitLcd with chemcthera 卩、may cjus,e ihe cancer (o "disappear

进出口贸易专业术语中英文对照

银行英语: 出口信贷 export credit 出口津贴 export subsidy 商品倾销 dumping 外汇倾销 exchange dumping 优惠关税 special preferences 保税仓库 bonded warehouse 贸易顺差 favorable balance of trade 贸易逆差 unfavorable balance of trade 进口配额制 import quotas 自由贸易区 free trade zone 对外贸易值 value of foreign trade 国际贸易值 value of international trade 普遍优惠制 generalized system of preferences-GSP 最惠国待遇 most-favored nation treatment-MFNT -------------------价格条件 ---------------------- 价格术语trade term (price term) 运费freight 单价 price 码头费wharfage 总值 total value 卸货费landing charges 金额 amount 关税customs duty 净价 net price 印花税stamp duty 含佣价price including commission 港口税portdues 回佣return commission 装运港portof shipment 折扣discount,allowance 卸货港port of discharge 批发价 wholesale price 目的港portof destination 零售价 retail price 进口许口证inportlicence 现货价格spot price 出口许口证exportlicence 期货价格forward price 现行价格(时价)current price prevailingprice 国际市场价格 world (International)Marketprice 离岸价(船上交货价)FOB-free on board 成本加运费价(离岸加运费价) C&F-cost and freight 到岸价(成本加运费、保险费价) CIF-cost,insurance and freight --------------------交货条件 ---------------------- 交货delivery 轮船steamship(缩写S.S) 装运、装船shipment 租船charter (the chartered shep) 交货时间 time of delivery

焊接专业术语中英文对照整理

机械——焊接专业术语中英文对照 (郭运)整理 1Single 单面的 2V—groove V型坡口 3Joint 焊接接头 4Edges overlap 接头形式 5Butt 对接 6T T型焊接 7Fillet 角焊缝 8Edge 端接 9Corner 角接 10Radius 半径 11Joint root 焊接根部 12Bevel angle 削边角度 13Groove angle 坡口角度 14Root face 根部钝边 15Groove face 坡口面 16Plug weld 塞焊 17Spot weld 点焊 18Seam weld 缝焊 19Slot weld 槽焊 20Double—flare—bevel—groove K型坡口焊缝

21Single—flare—V 单面V型22Edge flange 翻边端接 23Corner flange 卷边端接 24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝 27Slot weld 槽焊缝 28Spot weld 点焊缝 29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚 40Toe 焊趾 41Buildup 堆焊 42Weld reinforcement 焊缝加强高

专业术语中英文对照表

语文课程与教学论 名词术语中英文对照表 the Chinese Course and Teaching and Learning Theory in Chinese and English Teaching materials editing teaching materials /Chinese Teaching Materials /edit teaching materials /Uniformed Chinese Teaching Materials /Experimental Teaching Materials /Mother Tongue Teaching Materials /Teaching Materials of the New Course *textbook *reading book *teaching reference book *exercises book *studying plan Technology /Educational Technology /Modern Educational Technology /Educational Technology in Chinese Teaching /multi-media technology /net technology /cloud serving technology *white board *net meeting *chat room *blog Teaching Basic Theory of the Teaching teaching aim teaching task teaching objective teaching model teaching tactics teaching principle teaching program teaching reform teaching case Courseware teaching resources teaching experiment /mother tongue teaching A Term List of 1. 教材( JC ) 教材编写 /语文教材 /编写教材 / 统编教材 /实验教材 /母语教材 /新课程教材 * 课本 * 读本 * 教学参考书(教参) * 练习册 *学案 2. 技术( JS ) / 教育技术 /现代 教育技术 /语文 教育技术 /多媒 体技术 / 网络 技术 /云服务技 术 * 白板 *网 络会议 *聊天室 * 博克 3. 教学 (JX ) 教学基本理论 教学目的 教学 任务 教学目标 教学模式 教学 策略 教学原则 教学大纲 教学 改革 教学案例 教学课件 教学 资源 教学实验 /母语教学

飞机专业术语(英汉对照)

1、the airframe 机身,结构 2、The front (fore) part 前部 3、The rear (aft) part 后部 4、port 左旋(舵) 5、starboard 右旋(舵) 6、the inboard engine or inboards 内侧发动机 7、the outboard engine or outboards 外侧发动机 8、the nose 机头 9、the belly 腹部 10、the skin 蒙皮 11、the windscreen or windshield 风挡 12、the wing 机翼 13、the trailing edge 机翼后缘 14、the leading edge 机翼前缘 15、the wing tip 翼尖 16、the control surface 操纵面 17、ailerons 副翼 18、flaps (inboard flap,outboard flap,leading edge flaps) 襟翼(内侧襟翼,外侧襟翼,前缘缝翼) 19、spoilers (inboard\outboard spoiler)(spoiler down\up) 阻力板,扰流板(内、外侧扰流板)(扰流板放下、打开) 20、slats 缝翼 21、elevators (elevator control tab) 升降舵(升降舵操纵片) 22、rudder (rudder control tab) 方向舵(方向舵操纵片)

23、flap angle 襟翼角 24、flap setting 襟翼调整 25、the full flap position 全襟翼位置 26、a flapless landing 无襟翼着陆 27、the landing gear 起落架 28、stabilizer 安定面 29、the nose wheel 前轮 30、gear locked 起落架锁定 31、the wheel well 起落架舱 32、the wheel door 起落架舱门 33、a tyre 轮胎 34、to burst 爆破 35、a deflated tyre 放了气的轮胎 36、a flat tyre 走了气的轮胎 37、a puncture 轮胎被扎破 38、to extend the flaps (to retract the flaps) 放下襟翼(收上襟翼) 39、gear extention (gear retraction) 起落架放下(起落架收上) 40、The gear is jammed. 起落架被卡死。 41、The flaps are jammed. 襟翼被卡死。 42、the emergency extention system 应急放下系统 43、to crank the gear down 摆动放下起落架 44、the brakes 刹车

各种专业名称英语词汇中英文对照表

各种专业名称英语词汇中英文对照表

————————————————————————————————作者: ————————————————————————————————日期: ?

各种专业名称英语词汇中英文对照表 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学ChinesePhilosophy 外国哲学ForeignPhilosophies ?逻辑学Logic?伦理学Ethics 美学Aesthetics 宗教学Science of Religion?科学技术哲学Philosophy of Science andTechnology?经济学Economics?理论经济学Theoretical Economics ?政治经济学PoliticalEconomy ?经济思想史History ofEconomic Thought ?经济史History of Economic 西方经济学WesternEconomics?世界经济World Economics ?人口、资源与环境经济学Population,Resources andEnvironmentalEconomics 应用经济学Applied Economics 国民经济学National Economics?区域经济学Regional Economics ?财政学(含税收学)Public Finance (includingTaxation) 金融学(含保险学) Finance (including Insurance)?产业经济学Industrial Economics ?国际贸易学International Trade 劳动经济学Labor Economics ?统计学Statistics ?数量经济学Quantita tive Economics ?中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics?法学Law 法学Science of Law ?法学理论Jurisprudence?法律史Legal History ?宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence 民商法学(含劳动法学、社会保障法学)Civil Law and Commercial Law (i ncluding Science of LabourLawand Science ofSocial Sec urityLaw)?诉讼法学Science of ProcedureLaws ?经济法学Sc ience ofEconomic Law ?环境与资源保护法学Science ofEnvironment andNatural Resources Protection Law 国际法学(含国际公法学、国际私法学、国际经济法学、)Internationallaw (including International Public law, International PrivateLaw a

房务部专业术语中英文对照

房务部:Rooms Division 前厅部:Front Office 客房部:Housekeeping 大堂副理:Assistant Manager 宾客关系主任:Guest Relation Officer 前台:Front Desk 接待处:Reception/Check-in 收银处:Cashier/Check-out 领班:Captain 主管:Supervisor 班次负责人:Shift Leader 商务中心:Business Center 客房服务代表:Guest service agent(接待和收银合并之后的前台人员的称呼)简称GSA 电话总机:Switch Board 接线员:Operator 预订处:Room Reservation 礼宾服务处:Concierge 大厅服务处:Bell Service 金钥匙:Golden Key 行政楼层:Executive Floor 行政酒廊:Executive Lounge 行李生:Bellman 迎宾员:Doorman 夜审:End of Day /Night auditor 2.前厅服务项目专业术语介绍 入住:Check-in 退房:Check-out 外币兑换:Foreign Currency Exchange 问询:Information 接送机服务:Pick up service 叫醒服务:Wake up call 请勿打扰服务:DND Do not disturbed 失物招领:Lost and Found 国内直拨和国际直拨电话:DDD and IDD Domestic Direct Dial and International Direct Dial对方付费电话:Collect Call 3.前厅常用物品术语介绍: 住宿登记单:Registration card 欢迎卡:Welcome card 订房凭证:Voucher 交接本:log book 信封:Envelope 房卡钥匙:Room key 安全保管箱:Safe Deposit Box 客房统计和出售率统计的术语 预离房:Expected Departure 预抵房:Expected Arrival

常用焊接术语中英文对照

常用焊接术语中英文对照 焊接Welding 10.1 焊接种类Varieties of Welding 电弧焊arc welding 电熔焊electric fusion welding (EFW) 气熔焊fusion gas welding (FGW) 电阻焊electric resistance welding (ERW) 有保护的金属电弧焊shielded metal arc welding (SMAW) 手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW) 自动埋弧焊automatic submerged arc welding 金属极隋性气体保护电弧焊gas metal arc weiding (GMAW) 氩弧焊argon-arc welding, 气体保护电弧焊gas-shielded arc welding 气焊gas welding; flame welding 等离子焊plasma welding 硬钎焊braze welding 电渣焊electroslag welding 爆炸焊explosive welding 10.2 焊接形式Type of Welding

角焊fillet welding 间断焊intermittent welding 点焊spot welding 对焊butt welding 搭焊lap welding 塞焊plug welding 珠焊bead welding 槽焊slot welding 堆焊build up welding 垫板焊backing weld 坡口groove V形坡口V groove 单面U形坡口single U groove K形坡口double bevel groove X形坡口double V groove 双面U形坡口double U groove U-V组合坡口combination U and V groove 根部间隙root gap 焊接符号symbol of weld 错边量alignment tolerance 10.3 焊接位置Welding Position 仰焊overhead welding 现场焊field weld (F.W.)

电气专业术语中英文对照

一.电气名词 Electric items 二.线路(母线、回路)Lines (Bus , circuits) 三.设备 Equipments 四.保护、继电器 Protection , relays 五.电气仪表 Electric instruments 六.防雷 Lightning protection 七.接地 Grounding , earthing 八.室、所 Room , Substation 九.电修车间设备 Equipments of electric repair 十.材料 Material 十一.图名 Drawings , diagrams 十二.表头 Tables 十三.标准图词汇 Terms from standard DWG 一.电气名词 Electric items 交(直)流 Alternating (direct) current 短路电流 Short-circuit current 起始次暂态短路电流 Initial subtransient short-circuit current 冲击电流 Impulse current 稳态短路电流 Steady state short-circuit current 临界电流 Critical current 切断电流 Rupturing current 熔断电流 Blow-out current 故障电流 Fault current 计算电流 Calculating current 极限有限电流 Limit effective current 过电流 Over current 逆电流 Inverse current 整定电流 Setting current 额定电流 Rated current 电流密度 Current density 短路电流最大有效值 Maximum effective value of short-circuit current 高压 High-voltage , High-tension 低压 Low-voltage , Low-tension 计算电压 Calculating voltage 激磁电压 Exciting voltage 冲击电压 Impulse voltage 临界电压 Critical voltage 残留电压 Residual voltage 击穿电压 Puncture voltage 脉动电压 Pulsating voltage 供电电压 Supply voltage 电力电压 Power voltage

焊接缺陷中英文对照

精心整理 焊接缺陷 1. 裂缝:crack (焊缝/弧坑/热影响区裂纹:weldmetal/crater/heat-affectedZone(HAZ)crack ) 2. 焊瘤:overlap 3. 冷隔:coldlap 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 塌陷:excessivepenetration 16. 凹坑:pit/dent 17. 过度打磨:excessivegrinding 18. 焊疤:scar 19. 飞溅:spatter

20.焊缝成行不好:poorprofile 21.焊角不足:lackofweldleg 附录attachment 焊接工艺方法 1.熔焊:fusionwelding压焊:pressurewelding钎焊:brazingwelding 2.焊缝倾角:weldslope,inclinationofweldaxis. 3.焊缝转角:weldrotation,angleofrotation 4.平焊 5.立焊 6. 7. 8. 9. 10. 11. 12. 13. 14.I 15.Y 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.堆焊 29.衬垫焊:weldingwithbacking. 30.焊剂垫焊:weldingwithfluxbacking 31.电弧点焊:arcspotwelding. 32.套环:ferrule试板testpiece随机检查randomcheck 33.单面/双面串联点焊:direct/indirectserialspotswelding. 34.机械性能试验mechanicalpropertiestest 35.简历curriculumvitae 36.分类category 37.风险评估riskassessment 38.第三方notifiedbody 39.基准modules

制药行业术语中英文对照

术语表 Acceptance Criteria–接受标准:接受测试结果的数字限度、范围或其他合适的量度标准。Active Pharmaceutical Ingredient(API)(or Drug Substance)-活性要用成分(原料药)旨在用于药品制造中的任何一种物质或物质的混合物,而且在用于制药时,成为药品的一种活性成分。此种物质在疾病的诊断,治疗,症状缓解,处理或疾病的预防中有药理活性或其他直接作用,或者能影响机体的功能和结构。 API Starting Material–原料药的起始物料:用在原料药生产中的,以主要结构单元被并入该原料药的原料、中间体或原料药。原料药的起始物料可能是在市场上有售,能够根据合同或商业协议从一个或多个供应商处购得,或者自己生产。原料药的起始物料通常有特定的化学特性和结构。 Batch(or Lot)-批:有一个或一系列工艺过程生产的一定数量的物料,因此在规定的限度内是均一的。在连续生产中,一批可能对应与生产的某以特定部分。其批量可规定为一个固定数量,或在固定时间间隔内生产的数量。 Batch Number(or Lot Number)-批号用于标识一批的一个数字、字母和/或符号的唯一组合,从中可确定生产和销售的历史。 Bioburden–生物负载:可能存在与原料、原料药的起始物料、中间体或原料药中的微生物的水平和种类(例如,治病的或不治病的)。生物负载不应当当作污染,除非含量超标,或者测得治病生物。 Calibration–校验:证明某个仪器或装置在一适当的量程范围内测得的结果与一参照物,或可追溯的标准相比在规定限度内。 Computer System–计算机系统:设计安装用于执行某一项或一组功能的一组硬件元件和关联的软件。 Computerized System–计算机化系统与计算机系统整合的一个工艺或操作。Contamination–污染:在生产、取样、包装或重新包装、贮存或运输过程中,具化学或微生物性质的杂质或外来物质进入或沾染原料、中间体或原料药。 Contract Manufacturer–协议制造商:代表原制造商进行部分制造的制造商。 Critical–决定性的:用来描述为了确保原料药符合规格标准,必须控制在预定范围内的工艺步骤、工艺条件、测试要求或其他有关参数或项目。 Cross-Contamination–交叉污染:一种物料或产品对另一种物料或产品的污染。 Deviation–偏差:对批准的指令或规定的标准的偏离。 Drug(Medicinal)Product–药品:经最后包装准备销售的制剂(参见Q1A) Drug Substance–药物见原料药 Expiry Date(or Expiration Date)-有效期:原料药容器/标签上注明的日期,在此规定时间内,该原料药在规定条件下贮存时,仍符合规格标准,超过这以期限则不应当使用。 Impurity–杂质:存在与中间体或原料药中,任何不希望得到的成分。 Impurity Profile–杂质概况:对存在于一种原料药中的已知和未知杂质的描述。 In-Process Control(or Process Control)-中间控制:生产过程中为监测,在必要时调节工艺和/或保证中间体或原料药符合其规格而进行的检查。 Intermediate–中间体:原料药工艺步骤中生产的、必须经过进一步分子变化或精制才能成为原料药的一种物料。中间体可以分离或不分离。 Manufacture–制造:物料的接收、原料药的生产、包装、重新包装、贴签、重新贴签、质量控制、放行、贮存和分发以及相关控制的所有操作。 Material–物料:原料(起始物料,试剂,溶剂),工艺辅助用品,中间体,原料药和包装及贴签材料的统称。

电影专业术语 中英对照

电影专业术语中英文对照 A Above-the-line 线上费用 A-B roll A-B卷 AC 交流电 Academy ratio 学院标准画框比 Adaptation 改编 ADR editor ADR 剪辑师 Aligator clamp=gaffer grip 固定灯具的弹簧夹,又称鳄鱼夹 Ambient Sounds 环境音 Amp 安培 Amplification 信号放大 Amplitude 振幅 Analog 模拟 Anamorphic lens 变形镜头 Aperture 光圈 Answer Print 校正拷贝 Arc 摄像机的弧度运动 Art director 艺术指导 Aspect ratio 画框比 Atmosphere sound 气氛音 Attack 起音 Audio board 调音台 Audio mixer 混音器,混音师 Automatic dialogue replacement 自动对白补录 Automatic focus 自动对焦 Automatic gain control 自动增益控制 Automatic iris 自动光圈(少用) Axis of action 表演轴线 B Back light 轮廓光 Background light=Scenery light 场景光 Balance 平衡 Balanced 平衡电缆 Barndoor 遮扉(灯具上的黑色金属活动板,遮光用的) Barney 隔音套 Base 片基(用来附着感光乳剂的胶片基底) Base plate 底座(固定灯的) Baselight level 基本亮度 Batch capturing 批次采集 Below-the-line 线下费用 Bidirectional 双向麦克风 Bit depth 位元深度(在数字声音中每次取样的数目,通常是8,12,16)

工程专业术语中英文对照

工程专业术语中英文对照

CDB工程专业术语中英文对照(二) 添加时间:2013-4-24 节流截止放空阀 2011-08-10 16:50:46| 分类:English | 标签:|字号大中小订阅 六、仪表及自动控制 通用描述 COMMON DESCRIPTION 设备名称Equipment Name 缩写 ABB. 分散控制系统Distributed Control System DCS 安全仪表系统Safety Instrumentation System SIS 紧急切断系统Emergency Shutdown system ESD 火气系统Fire and Gas system F&G 监视控制和数据采集系统 Supervisory Control and Data Acquisition SCADA 可编程逻辑控制器Programmed Logic Controller PLC 远程终端单元Remote Terminal Unit RTU 站控系统Station Control System SCS 中央控制室Central Control Room CCR 操作间Operation room 机柜间Equipment room/ Cabinet room 大屏显示系统Large Screen Display system LSD 流量类仪表 FLOW INSTRUMENT 设备名称Equipment Name 孔板Orifice Plate 文丘里流量计Venturi Flowmeter 均速管流量计Averaging Pitot Tube 阀式孔板节流装置 Orifice Plate in quick change fitting 涡轮流量计Turbine Flowmeter

焊接缺陷和检验术语

焊接缺陷和检验术语 一、焊接缺陷 1、焊接缺陷焊接过程中在焊接接头中产生的金属不连续、不致密或连接不良的现象。 2.未焊透焊接时接头根部未完全熔透的现象,对对接焊缝也指焊缝深度未达到设计要求的现象。 3.未熔合熔焊时,焊道与母材之间或焊道与焊道之间,未完全熔化结合的部分,电阻点焊指母材与母材之间未完全熔化结合的部分。 4.夹渣焊后残留在焊缝中的焊渣。 5.夹杂物由于焊接冶金反应产生的,焊后残留在焊缝金属中的微观非金属杂质(如氧化物、硫化物等)。 6.夹钨钨极惰性气体保护焊时由钨极进入到焊缝中的钨粒。7.气孔焊接时,熔池中的气泡在凝固时未能逸出而残留下来所形成的空穴。气孔可分为密集气孔、条虫状气孔和针状气孔等。 8.咬边由于焊接参数选择不当,或操作方法不正确,沿焊趾的母材部位产生的沟槽或凹陷。 9.焊瘤焊接过程中,熔化金属流淌到焊缝之外未熔化的母材上所形成的金属瘤。 10.白点在焊缝金属拉断面上,出现的如鱼目状的一种白色圆形斑点。

11.烧穿焊接过程中,熔化金属自坡口背面流出,形成穿孔的缺陷。 12.凹坑焊后在焊缝表面或焊缝背面形成的低于母材表面的局部低洼部分。 13.未焊满由于填充金属不足,在焊缝表面形成的连续或断续的沟槽。 14.下塌单面熔化焊时,由于焊接工艺不当,造成焊缝金属过量透过背面,而使焊缝正面塌陷,背面凸起的现象。二、焊接裂纹 1.焊接裂纹在焊接应力及其他致脆因素共同作用下,焊接接头中局部地区的金属原子结合力遭到破坏而形成的新界面所产生的缝隙。它具有尖锐的缺口和大的长宽比的特征。2.热裂纹焊接过程中,焊缝和热影响区金属冷却到固相线附近的高温区产生的焊接裂纹。 3.弧坑裂纹在弧坑中产生的热裂纹。 4.冷裂纹焊接接头冷却到较低温度下(对于钢来说在MS温度以下)时产生的焊接裂纹。 5.延迟裂纹钢的焊接接头跨却到室温后并在一定时间(几小时、几天、甚至十几天)才出现的焊接冷裂纹。 6.焊根裂纹沿应力集中的焊缝根部所形成的焊接冷裂纹。7.焊趾裂纹沿应力集中的焊趾处所形成的焊接冷裂纹。8.焊道下裂纹在靠近堆焊焊道的热影响区内所形成的焊接

高分子专业术语中英文对照表

高分子专业术语中英文对照表

加工processing 反应性加工reactive processing 等离子体加工plasma processing 加工性processability 熔体流动指数melt [flow] index 门尼粘度Mooney index 塑化plasticizing 增塑作用plasticization 内增塑作用internal plasticization 外增塑作用external plasticization 增塑溶胶plastisol 增强reinforcing 增容作用compatibilization 相容性compatibility 相溶性intermiscibility 生物相容性biocompatibility 血液相容性blood compatibility 组织相容性tissue compatibility 混炼milling, mixing 素炼mastication 塑炼plastication 过炼dead milled 橡胶配合rubber compounding 共混blend 捏和kneading 冷轧cold rolling 压延性calenderability 压延calendering 埋置embedding 压片preforming 模塑molding 模压成型compression molding 压缩成型compression forming 冲压模塑impact moulding, shock moulding 叠模压塑stack moulding 复合成型composite molding 注射成型injection molding 注塑压缩成型injection compression molding 射流注塑jet molding 无流道冷料注塑runnerless injection molding 共注塑coinjection molding 气辅注塑gas aided injection molding 注塑焊接injection welding 传递成型transfer molding

相关主题
相关文档 最新文档